11-Rubber & Plastics

MALAYSIAN STANDARDS
SECTORIAL CATALOGUE
2007
No. 11
RUBBER & PLASTICS INDUSTRIES
Department of Standards Malaysia

Ministry of Science, Technology & Innovation
Level 1 & 2, Block C4, Complex C
Federal Government Administrative Centre
62502 Putrajaya, MALAYSIA
Tel : 603-8885 8000

Fax : 603-8888 5060
E-Mail : info@standardsmalaysia.gov.my
http://www.standardsmalaysia.gov.my
INTRODUCTION
The Department of Standards Malaysia (Standards Malaysia) is the national standardisation and
accreditation body.
The main function of the Department is to foster and promote standards, standardisation and
accreditation as a means of advancing the national economy, promoting industrial efficiency and
development, benefiting the health and safety of the public, protecting the consumers, facilitating
domestic and international trade and furthering international cooperation in relation to standards and
standardisation.
Malaysian Standards are developed through consensus by committees which comprise of balanced
representation of producers, users, consumers and others with relevant interests, as may be appropriate
to the subject in hand. These standards where appropriate are adoption of international standards.
Approval of a standard as a Malaysian Standard is governed by the Standards of Malaysia Act 1996
(Act 549). Malaysian Standards are reviewed periodically. The use of Malaysian Standard is voluntary
except in so far as they are made mandatory by regulatory authorities by means of regulations, local
by-laws or any other similar ways.
The Department of Standards Malaysia appoints SIRIM Berhad as the agent to develop Malaysian
Standards.
The Industry Standards Committees (ISCs) established by SIRIM Berhad are responsible for the
development of Malaysian Standards in their respective areas, as follows:
ISC A - Food and Agriculture

ISC B - Chemicals and Materials
ISC C - Consumer Products, Personal Safety and Services
ISC D - Building and Civil Engineering
ISC E - Electrotechnical
ISC F - Mechanical Engineering
ISC G - Information Technology, Communications and Multimedia
ISC H - Petroleum and Gas
ISC J - Plastics and Plastics Products
ISC K - Packaging and Distribution
ISC L - Road Vehicles
ISC M - Fire Safety and Prevention
ISC N - Rubber and Rubber Products
ISC W - Occupational Health and Safety
NC Y - Quality Management and Quality Assurance
NC Z - Environmental Standards
More than 100 standards development committees involving more than 1500 individuals, have been
established under the ISCs.
(ii)
Malaysian Standards Sectorial Catalogue 2007
This sectorial catalogue lists as at September 2007, Malaysian Standards that have been established
on product specifications, codes of practice, terminologies, guides and method of test on selected
sectors.
New standards, revisions, amendments, addenda, errata and reconfirmed standards as well as
standards that have been withdrawn are published bi-monthly in the SIRIM Berhad’s newsletter
Standards and Quality News.
An online system is available for searching and online purchasing. Payment can be made by credit
card. The system is called the MS Online System and can be accessed at http://www.msonline.gov.my.
The MS Online system contains over 4,000 Malaysian standards on all sectors.
List of Sectorial Catalogue 2007
1. Quality Management System, Environmental Management System & Safety and Health Protection
2. Health Care Technology, Metrology and Measurement. Testing
3. Mechanical and Fluid System and Components. Manufacturing Engineering, Energy and Heat
Transfer Engineering
4. Electrical Engineering & Electronics
5. Telecommunication, Information Technology. Office Equipment
6. Road Vehicles Engineering, Material Handling Equipment, Packaging & Distribution of Goods.
7. Textile and Leather Technology and Clothing Industry
8. Agriculture and Food Technology
9. Chemical Technology, Mining and Minerals, Petroleum and related technology & Metallurgy
10. Wood Technology, Glass & Ceramics Industries, Paper Technology and Paints & Colour Industries
11. Rubber & Plastics Industries
12. Constructions Materials & Building. Civil Engineering. Housekeeping. Entertainment. Sports.
ABBREVIATIONS
MS : Malaysian Standard
MS ISO : Malaysian Standard which is identical to International Organization for

Standardization (ISO) Standard. The numbering of the standard is identical to that
of the ISO Standard except for the prefix.
MS ISO/IEC : Malaysian Standard which is identical to the Joint ISO and IEC Standard. The
numbering of the standard is identical to that of the ISO/IEC Standard except for
the prefix.
MS.....(P) : Provisional Standard
Malaysian Standard which is adopted/adapted from international, regional or foreign national standard
without undergoing standards development committee deliberations due to its urgent need, as iden-
tified by the Department of Standards Malaysia. Provisional Standards are identified by a letter “P”
following the MS number.
(iii)
SUBJECT STRUCTURE ACCORDING TO
INTERNATIONAL CLASSIFICATION OF STANDARDS
01. Generalities. Terminologies. Standardization 61. Clothing Industry.
03. Sociology. Services. Company Organization 65. Agriculture.

and Management. Administration. Transport.
67. Food Technology.
07. Mathematics. Natural Sciences.
71. Chemical Technology.
11. Health Care Technology.
73. Mining and Minerals.
13. Environment. Health Protection. Safety
75. Petroleum and Related Technologies.
17. Metrology and Measurement. Physical
Phenomena 77. Metallurgy.
19. Testing. 79. Wood Technology.
21. Mechanical Systems and Components for 81. Glass and Ceramics Industries.
General Use.
83. Rubber and Plastics Industries.
23. Fluid Systems and Components for General
Use. 85. Paper Technology.
25. Manufacturing Engineering. 87. Paint and Colour Industries.
27. Energy and Heat Transfer Engineering. 91. Construction Materials and Building.
31. Electronics. 93. Civil Engineering.
33. Telecommunications. Audio and Video 95. Military Engineering.

Engineering.
97. Domestics and Commercial Equipment.
35. Information Technology. Office Machines. Entertainment. Sports.
37. Image Technology.
39. Precision Mechanics. Jewellery.
43. Road Vehicles Engineering.
45. Railway Engineering.
47. Shipbuilding and Marine Structures.
49. Aircraft and Space Vehicle Engineering.
53. Materials Handling Equipment.
55. Packaging and Distribution of Goods.
59. Textile and Leather Technology.
(iv)
CONTENTS
Page
Introduction ------------------------------------------------------------------------------------------------------------------------ (ii)
Malaysian Standards Sectorial Catalogue ----------------------------------------------------------------------------- (iii)
Abbreviation ----------------------------------------------------------------------------------------------------------------------- (iii)
Subject Structure by ICS ----------------------------------------------------------------------------------------------------- (iv)
RUBBER & PLASTICS INDUSTRIES
Manufacturing processes in the rubber and plastics industries ------------------------------------------ 1

Raw materials for rubber and plastics in general ------------------------------------------------------------ 1
Latex and raw rubber ----------------------------------------------------------------------------------------------- 1
Rubber compounding ingredients ------------------------------------------------------------------------------- 3
Auxiliary materials and additives for plastics ----------------------------------------------------------------- 3
Rubber ------------------------------------------------------------------------------------------------------------------ 3
Plastics ----------------------------------------------------------------------------------------------------------------- 8
Plastics in general --------------------------------------------------------------------------------------------------- 9
Thermosetting materials ------------------------------------------------------------------------------------------- 15
Thermoplastic materials -------------------------------------------------------------------------------------------- 16
Cellular materials ---------------------------------------------------------------------------------------------------- 18
Reinforced Plastic --------------------------------------------------------------------------------------------------- 19
Rubber and plastic products -------------------------------------------------------------------------------------- 20
Rubber and plastics products in general ---------------------------------------------------------------------- 20
Films and sheets ----------------------------------------------------------------------------------------------------- 22
Plastics pipes, fittings and valves ------------------------------------------------------------------------------- 28
Hoses ------------------------------------------------------------------------------------------------------------------ 26
Seals -------------------------------------------------------------------------------------------------------------------- 27
Other rubber and plastic products ------------------------------------------------------------------------------- 27
Tyres -------------------------------------------------------------------------------------------------------------------- 28
Road vehicle tyres --------------------------------------------------------------------------------------------------- 29
Adhesives -------------------------------------------------------------------------------------------------------------- 30
Equipment for rubber and plastics industries ---------------------------------------------------------------- 31
Numerical Listing ---------------------------------------------------------------------------------------------------- 32

Index -------------------------------------------------------------------------------------------------------------------- 36
Order Form ------------------------------------------------------------------------------------------------------------ 42
(v)
83. RUBBER AND PLASTICS INDUSTRIES
MS 281 : Part 5 : 1998
83.020 Manufacturing processes in the Specification for natural rubber latex concentrate : Part 5 :
Determination of mechanical stability (Third revision).
rubber and plastics industries
This Malaysian Standard specifies a method for the determination
of the mechanical stability of natural rubber latex concentrate.
Price RM10
MS 1010 : 1986
Specification for rigid polyvinyl chloride and related plastic MS 281 : Part 6 : 1998
pipe and fitting compounds. Specification for natural rubber latex concentrate (Includ-
Price RM30 ing raw natural rubber) : Part 6 : Determination of coagulum
content (Third revision).
This Malaysian Standard specifies a method for the determination
83.040.01 Raw materials for rubber and of the coagulum content (sieve residue) of the natural rubber latex
plastics in general concentrate.
Price RM10
MS 506 : 1977 (2004) MS 281 : Part 10 : 1999

Specification for ammonia (anhydrous and aqueous). Natural rubber latex concentrate : Part 10 : Determination of
Covers grade of materials used as anti-coagulant for fresh natural volatile fatty acid number (Third revision).
latex, and as a long term preservative for natural rubber latex Specifies a method for the determination of the volatile fatty acid
concentrates. number of natural rubber latex concentrate. This standard is
technically equivalent to ISO 506 : 1992 except that kneading is
Price RM20
carried out using a glass rod and beaker whilst in the ISO standard,
kneading is carried out using a mortar and pestle and the end point
83.040.10 Latex and raw rubber for titration is defined whereas it is not stated in the ISO standard.
It supersedes MS 281 : Part 10 : 1992.
Price RM10
MS 281 : Part 1 : 1999 MS 281 : Part 11 : 1999

Natural rubber latex concentrate : Part 1 : Methods of sampling Specification for natural rubber latex concentrate : Part 11 :
(Third revision) Determination of KOH number (Third revision).
Specifies procedures for the sampling of natural rubber latex Specifies a method for the determination of the KOH number of
concentrate. It is suitable for the sampling of latex concentrates that natural rubber latex concentrate. This standard is technically
is contained in drums, crates, bags and tanks. This standard is equivalent to ISO 127 : 1995 and it supersedes MS 281 : Part 11 :
technically equivalent to ISO 123 : 1985 except for the inclusion of 1992.
the closed-head type drum in the manual process of homogenising Price RM10
latex concentrate. It supersedes MS 281 : Part 1 : 1992.
Price RM10 MS 281 : Part 12 : 2001
Natural rubber latex concentrate - Determination of boric
acid content (Third revision)
Best Seller This Malaysian Standard specifies a procedure for the determination
of boric acid in natural rubber latex concentrate. The procedure is
not necessarily suitable for latices from natural sources other than
Hevea brasiliensis or for latices of synthetic rubber, compounded
latex, vulcanized latex or artificial dispersions of rubber. This
MS 281 : Part 2 : 1998 standard supersedes MS 281 : Part 12 : 1992.
Specification for natural rubber latex concentrate. Part 2: Price RM10
Determination of total solid content (Third revision).
This Malaysian Standard specifies a method for the determination MS 281 : Part 14 : 2001
of the total solids content of natural rubber latex concentrate. Rubber, raw natural, and rubber latex, natural -
Price RM10 Determination of nitrogen content (Third revision)
This Malaysian Standard specifies a macro-method and a semi-
MS 281 : Part 3 : 1998 micro method for the determination of nitrogen in raw natural rubber
Specification for natural rubber latex concentrate : Part 3 : and in natural rubber latex using variants of the Kjeldahl process.
Determination of dry rubber content (Third revision). This standard supersedes MS 281: Part 14: 1993.
This Malaysian Standard specifies a method for the determination of Price RM20
the dry rubber content of natural rubber latex concentrate.
Price RM10
MS 281 : Part 4 : 1999

Natural rubber latex concentrate : Part 4 : Determination of
alkalinity (Third revision)
Specifies a method for the determination of the alkalinity of natural
rubber latex concentrate. This standard is technically equivalent to
ISO 125 : 1995 and its supersedes MS 281: Part 4 : 1992.
Price RM10
1
MS 281: Part 15: 1992 under diffuse daylight illumination against a matt white background
Specification for natural rubber latex concentrate: Part 15: and comparison slide containing standard calibrated colour glasses
determination of viscosity (Second revision) are used.
This Malaysian Standard specifies a method for the determination Price RM10
of the viscosity of natural rubber latex concentrate.
Price RM10 MS 1359 : Part 6 : 1994
Test methods for technically specified raw natural rubber
MS 281 : Part 16 : 1999 : Part 6 : Determination of rapid plasticity and plasticity re-
Natural rubber latex concentrate : Part 16 : Determination of tention index.
ph (Third revision) This Malaysian Standard specifies a method for the determination
Specifies a method for the determination of the pH of natural rubber of initial rapid plasticity and plasticity retention index of rubber. The
latex concentrate. This standard is technically equivalent to ISO oxidation behaviour of raw natural rubber may have an important
976: 1996 and it supersedes MS 281: Part 16: 1992. bearing on processing behaviour and end product performance
Price RM10 and the plastic retention index test afford a convenient means of
characterising rubber in certain aspects.
MS 297: 1981 Price RM10
Specification for raw natural rubber (First revision)
Specifies minimum quality requirements for various grades. Tests in MS 1359 : Part 7 : 1995
accordance with MS 298. Test methods for technically specified raw natural rubber
Price RM10 : Part 7 : Determination of mooney accelerated storage
hardening test (MASHT).
MS 298 : 1985 This Malaysian Standard specifies a method of measuring the storage
Methods of sampling and test for raw natural rubber (First hardening raw natural rubber using the Mooney shearing disc
revision). viscometer. In this test, accelerated storage-hardening is achieved
Test methods are provided for the determination of dirt, volatile by storing rubber portions over phosphorus pentoxide in a vacuum
matter, nitrogen, ash, rapid plasticity and plasticity retention, index, at 60°C ± 1°C for 48 ± 0.1h. The resultant increase in viscosity (Dv)
colour, Mooney viscosity, accelerated and storage hardening test represents the accelerated storage-hardening.
(ASHT), acetone extract, vulcanisation characteristics (MOD) and Price RM10
curing characteristics with the oscillating disk curement.
Price RM50 MS 1359 : Part 8 : 1995
Test methods for technically specified raw natural rubber
MS 317 : 1986 : Part 8 : Determination of wallace accelerated storage
Specification for evaporated preserved natural rubber hardening test (WASHT).
latices (First revision). This Malaysian Standard specifies a method of measuring the
Covers requirements for NR latex, type HA evaporated; NR latex, accelerated storage hardening of raw natural rubber suing the
type KHS evaporated; NR latex, type KLS evaporated. wallace plastimeter. The test involves measurement of the plasticity
Price RM10 of standard pellets before and after a short period of storage under
conditions which accelerate the storage hardening reaction.
MS 466 : 1987 Price RM10
Methods of sampling and testing field latex (First revision).
Test methods applicable to fluid field latex preserved with any of MS 1392 : 1998
the following (or suitable combinations): ammonia; potassium Test method for the analysis of extractable proteins in
hydroxide; sodium sulphate; formaldehyde; and boric acid. natural rubber products.
Price RM20 This Malaysian Standard provides an analytical test method for
determining the quantity of total extractable proteins in natural rubber
MS 1157 : Part 41 : 1999 (NR) products. The test comprises essentially four parts namely:
Methods of test for vulcanized rubber : Part 41 : a) sample preparation,
Determination of temperature rise and resistance to fatigue b) protein extraction,
in compression flexometer testing c) protein precipitation and,
Specifies the compression flexometer test for the determination of d) colourimetric assay.
the temperature rise and resistance to fatigue of vulcanized rubbers. The protein content is then determined by using Lowry microassay.
The flexometer specified is known as the Goodrich flexometer, but This standard is intended to supersede the Provisional Malaysian
any other apparatus giving equivalent performance may be used. Standard MS 1392 : 1996(P).
Price RM20 Price RM10 Amendment 1 : 2001
MS 1359 : Part 4 : 1994 MS 1541 : 2002

Test methods for technically specified raw natural rubber Rubber latex, natural, concentrate - Determination of sludge
: Part 4 : Determination of mooney viscosity. content
This Malaysian Standard specifies a method for the determination This Malaysian Standard specifies a method for the determination
of Mooney Viscosity of rubber using a shearing-disc Mooney of the sludge content of natural rubber latex concentrate. The
Viscometer. The torque necessary to rotate the disc in a cylindrical method is not necessarily suitable for latices from natural sources
chamber filled with rubber under specified conditions is determined other than Heavea brasiliensis. It is not suitable for compounded
and the number proportional to this torque is taken as the viscosity latex or vulcanized latex.
of the rubber. Price RM10
Price RM10
MS 1542 : 2002
MS 1359 : Part 5 : 1994 Rubber, raw natural - Determination of dirt content
Test methods for technically specified raw natural rubber This Malaysian Standard specifies a method for the determination
: Part 5 : Determination of colour. of the dirt content of raw natural rubber. It is not applicable to dirt
This Malaysian Standard specifies a method for the determination present as surface contamination. This standard supersedes MS
of Lovibond Colour index of rubber. Colour matching is carried out 1359 : Part 3 : 1994. Price RM20
2
MS 1549 : 2002 monomer by gas chromatography in homopolymer and copolymer
Test method for determination of residual powder on power free resins of vinly chloride, as well as materials and articles made from
rubber medical gloves resins.
This Malaysian Standard is designed to determine the amount of Price RM10
residual power (or filter-retained mass) found on gloves described
as non powdered, powder free, powderless, no powder, or other words
to that effect. The test method covers the determination of average 83.040.30 Auxiliary materials and additives for
powder or filter-retained mass found on a sample of medical gloves.
Price RM10 plastics
_____________________________________________
MS 1550 : 2002
Test method for determination of residual powder on powdered MS 511 : 1977
rubber medical gloves Specification for zinc oxide for use in rubber.
This Malaysian Standard is designed to determine the amount of Covers zinc oxide intended for use as activator, pigment, accelerator
residual power (or filter-retained mass) found on powdered gloves. and reinforcing materials in rubber compounds. Two grades as
The test method covers the determination of the amount of residual specified : Grade A (non-straining) and Grade B (general purpose).
powder and non-powder solids found on medical gloves. The mass Price RM60
found for powdered gloves is assumed to be a combination of water-
insoluble residue remaining after the manufacturing process, former
release agents and donning powder. 83.060 Rubber
Price RM10
MS ISO 36 : 2002
Rubber, vulcanized or thermoplastic - Determination of adhesion MS 463 : 1994
to textile fabric Specification for rubber (Hevea brasiliensis L.) seed for
This Malaysian Standard specifies a method of test for measuring commercial planting (First revision).
the force required to separate, by stripping; two plies of fabric bonded This Malaysian Standard prescribes the quality requirements for
with rubber, or a rubber layer and a fabric ply bonded together. The rubber (Hevea brasiliensis) seeds for commercial plantings.
method is applicable when the ply surfaces are approximately plane Price RM20
or when they are in the form of a cylinder having an internal diameter
greater than approximately 50 mm. The method is not applicable
when the ply surfaces contain sharp bends, angles or other gross
irregularities which cannot be excluded when cutting out test pieces.
Price RM10
MS ISO 296 : 2001

Natural rubber latex concentrate - Centrifuged or creamed,
ammonia-preserved types - Specification
This Malaysian Standard gives specifications for natural rubber latex
concentrate types which are preserved wholly or in part with ammonia
which have been produced by centrifuging or creaming. This standard
supersedes MS 296 : 1990.
Price RM10
MS ISO 498 : 2002

Natural rubber latex concentrate - Preparation of dry films
This Malaysian Standard specifies a method for preparing dry,
homogeneous films, substantially free of air bubbles, from natural
rubber latex concentrate. The procedure is not necessarily suitable
for latices from natural sources other than Hevea brasiliensis or for
compounded latex, vulcanized latex or artificial dispersions of rubber MS 671 : Part 1 : 2002
or synthetic rubber latices. Specification for elastomeric bridge bearing : Part 1 : Material
Price RM10 testing, manufacture and installation of bearing (Second
revision)
MS ISO 6502 : 2002 This Malaysian Standard specifies requirements for the material,
Rubber - Guide to the use of curemeters manufacture, testing and installation of elastomeric bride bearing. It
This Malaysian Standard provides guidance on the determination of also specifies methods of test and describes procedures for the
vulcanization characteristics of rubber compounds by means of preparation of test pieces from finishes bearing. This standard does
curemeters. not contain aspects relating to design of bearing. This standard
Price RM30 supersedes MS 671 : Part 1 : 1991.
Price RM20
83.040.20 Rubber compounding ingredients MS 1157 : Part 16 : 1992

Methods of test for vulcanized rubber : Part 16 : Resistance to
ozone cracking - static strain test.
MS 1013 : 1986 This Part of the standard specifies a method for the determination of
Method of test for residual vinyl chloride monomer (Gas resistance of vulcanized or thermoplastic rubbers to cracking when
Chromatographic Method). exposed, under static tensile strain, to air containing a definite
Specifies a method for the determination of residual vinyl chloride concentration of ozone and at a definite temperature in circumstances
that exclude the effects of direct light.
Price RM20
3
MS 1157 : Part 18 : 1992 MS 1157 : Part 31 : 1992
Methods of test for vulcanized rubber : Part 18 : Determination Methods of test for vulcanized rubber : Part 31 : Determination
of modulus in shear-quadruple shear method. of adhesion to wire cord.
This standard specifies methods for the determination of the modulus This standard specifies two methods for determining the adhesion
in shear or the strength of bonds of rubber to metal or other rigid strength of vulcanized rubber to wire cord which is embedded in the
plates, using rubber bonded between four parallel plates. Method A rubber. These methods are applicable primarily to test pieces
describes the determination of the modulus in shear. Method B prepared in the laboratory under standard conditions, such as may
describes the determination of the strength of the bonds. be used for the development and control of materials and processes
Price RM10 used in the manufacture of products reinforced with wire cord.
Price RM20
MS 1157 : Part 19 : 1992
Methods of test for vulcanized rubber : Part 19 : Determination MS 1157 : Part 34 : 1991
of adhesion to rigid plates in shear-quadruple shear method. Methods of test for vulcanized rubber : Part 34 : Determination
This standard specifies a method for the determination of the strength of ageing characteristics by measurement of stress at a given
of bonds of rubber to metal or other rigid plates where the rubber is elongation.
assembled between four parallel rigid plates. The method is applicable This Malaysian Standard describes three methods for the purpose
primarily to test pieces prepared in the laboratory under standard of determining the ageing characteristics of the vulcanized rubber.
conditions such as may be used to provide date for the development Price RM10
and control of rubber compounds and methods of manufacture of
bonded shear units. MS 1157 : Part 35 : 1991
Price RM10 Methods of test for vulcanized rubber : Part 35 : Determination
of tension fatigue.
MS 1157 : Part 22 : 1991 This Malaysian Standard describes a method for the determination
Methods of test for vulcanized rubber : Part 22 : Determina tion of the resistance of vulcanized rubbers to fatigue under repeated
of density. tensile deformations, the test piece size and frequency of cycling
This Malaysian Standard specifies two methods of test for the being such that there is little or no temperature rise. Under these
determination of the density of solid vulcanized rubber. Such conditions, failure results from the growth of a crack that ultimately
determinations are of importance in the control of the quality of a severs the test piece.
rubber compound and in the calculation of the mass of rubber required Price RM20
to produce a given volume of vulcanized rubber.
Price RM10 MS 1157 : Part 38 : 1991
Methods of test for vulcanized rubber : Part 38 : Determination
MS 1157 : Part 24 : 1991 of adhesion to metal-two-plate method.
Methods of test for vulcanized rubber : Part 24 : Antistatic and This Malaysian Standard specifies a method for determining the
conductive products - Determination of electrical resistance. adhesion strength of rubber-to-metal bands where the rubber part
This Malaysian Standard specifies a method of test to determine the is assembled between two parallel metal plates. The method is
electrical resistance of antistatic and conductive articles and products applicable primarily to test pieces prepared in the laboratory under
manufactured wholly or in part, from rubber whose electrical standard conditions, such as may be used to provide data for the
resistance measured between defined points, when new does not development of rubber compounds and control of methods of
exceed 1 x 108 and whose conductivity is derived from the addition manufacture.
of carbon black and/or other appropriate substances to the bulk of Price RM10
the material.
Price RM20 MS 1157 : Part 39 : 1991
Methods of test for vulcanized rubber : Part 39 : Preparation of
MS 1157 : Part 27 : 1993 samples and test pieces for chemical test.
Methods of test for vulcanized rubber : Part 27 : Determination This Part of the standard specifies a method of preparing samples
of rebound resilience. from vulcanized rubber for use in chemical test.
This Malaysian Standard describes two methods for determining the Price RM10
rebound resilience of rubber the hardness of which, at the test
temperature, lies between 30 IRHD and 85 IRHD. Method A uses MS 1157 : Part 40/1 : 1999
the Dunlop tripsometer whereas method B uses the Luke pendulum. Methods of test for vulcanized rubber : Part 40/1 : Determination
Results obtained using method A cannot be compared with results of abrasion resistance using a rotating cylindrical drum device
obtained using method B. In cases of dispute, method B shall be the Specifies a method for the determination of the resistance of rubber
referee test method. to abrasion by means of a rotating cylindrical drum device. The
Price RM30 method involves determination of the volume loss of a rubber test
piece through abrasive action by rubbing over a specified grade of
MS 1157 : Part 29 : 1992 abrasive cloth. This standard is technically equivalent to ISO 4649 :
Methods of test for vulcanized rubber : Part 29 : Determination 1985 except for the time sequence for the mixing procedure.
of static adhesion to textile cord-H-pull test. Price RM20
This standard specifies a method for the determination of the static
adhesion of textile tyre cord to vulcanized rubber. It is applicable to
cords made from natural or man-made fibres. This method may be
applied, if desired, to similar cords for use in other rubber products,
but it is limited to cords of linear density not exceeding 800 mg/m
(tex).
Price RM20
4
MS 1157 : Part 40/2 : 1999 MS 1449 : Part 6 : 1999
Methods of test for vulcanized rubber : Part 40/2 : Determination Rubber - Determination of metal content by atomic absorption
of abrasion resistance using abrasive wheel spectrometry : Part 6 : Determination of magnesium content
Specifies a method for the determination of the resistance of rubber Specifies an atomic absorption spectrometric method for the
to abrasion by means of an abrasive wheel. This method is restricted determination of the magnesium content of rubbers.
to rubbers with a hardness in the range of 55 IRHD to 95 IRHD. Price RM20
Price RM10
MS 1523 : 2001
MS 1157 : Part 41 : 1999 Rubber - Temperatures, humidities and times for conditioning
Methods of test for vulcanized rubber : Part 41 : Determination and testing
of temperature rise and resistance to fatigue in compression This Malaysian Standard specifies the temperature, humidity and
flexometer testing. time conditions used for the conditioning and testing of all types of
Specifies the compression flexometer test for the determination of rubber test piece. Special conditions applicable to a particular test
the temperature rise and resistance to fatigue of vulcanized rubbers. or material or simulating a particular climatic environment are not
Price RM20 included, nor are special requirements for testing whole products. It
also specifies the requirements for the time-interval to be observed
MS 1292 : 1992 between forming and testing of rubber test pieces and products. Such
Specification for rubber seals-water stops for sealing joints in requirements are necessary to obtain reproducible test results and
concrete - Specification of materials. to minimize disagreement between customer and supplier. This
This Malaysian Standard specifies requirements for materials used standard supersedes MS 1157 : Part 13 : 1995.
in vulcanized, solid rubber water stops for sealing joints in concrete Price RM10
into which they are wholly or partly embedded.
Price RM10 MS 1524 : 2001
Rubber - Determination of solvent extract
MS 1449 : Part 1 : 1999 This Malaysian Standard specifies two methods for the quantitative
Rubber - Determination of metal content by atomic absorption determination of extractable material from raw rubbers, both natural
spectrometry : Part 1 : Determination of zinc content and synthetic, and their unvulcanized and vulcanized compounds.
Specifies an atomic absorption spectrometric method for the Method B is a rapid extraction method, while method A is for use in
determination of the zinc content of rubbers. This standard is cases of dispute.
technically equivalent to ISO 6101-1991 except that the dissolution Price RM20
after ashing is carried out using concentrated nitric acid instead of
concentrated hydrochloric acid and treatment for silicates is not MS 1546 : 2002
included. Price RM20 Rubber - Determination of crystallization effects by hardness
measurements
MS 1449 : Part 3 : 1999 This Malaysian Standard specifies a test based on hardness
Rubber - Determination of metal content by atomic absorption measurements for determining the progressive stiffening of rubber
spectrometry : Part 3 : Determination of copper content with time, caused by crystallization. It is limited to materials having
Specifies an atomic absorption spectrometric method for the an initial hardness at test temperature of 10 IRHD to 85 IRHD.
determination of the copper content of rubbers. This standard is Price RM20
technically equivalent to ISO 6101-3 : 1997 except that the dissolution
after ashing is carried out with concentrated nitric acid instead of
MS 1547 : 2002
concentrated hydrochloric acid and treatment for silicates is not
Rubber latex - Determination of density between 5°C and 40°C
included. It supersedes MS 281 : Part 7 : 1993.
This Malaysian Standard specifies a method for the determination of
Price RM20
the density of natural rubber latex concentrate between the
temperatures of 5°C and 40°C. The standard is intended for use
MS 1449 : Part 4 : 1999
when density determinations are used to calculate the mass of a
Rubber - Determination of metal content by atomic absorption
measured volume of latex in locations where it is not practical to
spectrometry : Part 4 : Determination of manganese content
weigh directly or to control the temperature of the laboratory.
Specifies an atomic absorption spectrometric method for the
Price RM10
determination of the manganese content of rubbers. This standard
is technically equivalent to ISO 6101-4 : 1997 except that the
dissolution after ashing is carried out using concentrated nitric acid MS 1548 : 2002
instead of concentrated hydrochloric acid and treatment for is not Rubbers, raw - Determination of volatile-matter content
included. It supersedes MS 281 Part 8 : 1993. This Malaysian Standard specifies two methods, a hot-mill method
Price RM20 and an oven method, for the determination of moisture and other
volatile-matter content in raw rubbers. This standard supersedes
MS 1449 : Part 5 : 1999 MS 1359 : Part 2 : 1994.
Rubber - Determination of metal content by atomic absorption Price RM10
spectrometry : Part 5 : Determination of iron content
Specifies an atomic absorption spectrometric method for the MS 1568 : Part 7 : 2002
determination of the iron content of rubbers. This standard is Rubber – Determination of metal content by atomic absorption
technically equivalent to ISO 6101-5 : 1990 except that the dissolution spectrometry: Part 7: Determination of calcium content
after ashing is carried out with concentrated nitric acid instead of This part of Malaysian Standard specifies an atomic absorption
concentrated hydrochloric acid and the treatment for silicates is not spectrometric method for the determination of the calcium content of
included. It supersedes MS 281 : Part 9 : 1993. rubbers.
Price RM20 Price RM20
5
MS ISO 34-2 : 1999 MS ISO 287 : 1999
Rubber, vulcanized or thermoplastic – Determination of tear Paper and board – Determination of moisture content – oven –
strength - Part 2 : Small (delft) test pieces drying method
Specifies a method for the determination of the tear strength of small Specifies an oven-drying method for the determination of the moisture
test pieces (Delft test pieces) of vulcanized or thermoplastic rubber. content of paper and board at the time of sampling. The method is
This standard is identical with ISO 34-2 : 1996. applicable to all paper and board, including corrugated fibreboard
Price RM20 and solid fibreboard, provided that the paper or board does not contain
any substance, other than water, that will escape at the temperature
MS ISO 37 : 1998 specified for the test. This standard is identical with ISO 287 - 1985
Rubber vulcanised or thermoplastic – Determination of tensile and it supersedes MS 126 : 1973.
stress-strain properties Price RM10
This Malaysian Standard is identical with ISO 37 : 1994. This standard
describes a method for the determination of the tensile stress-strain MS ISO 289-1 : 1998
properties of vulcanized and thermoplastic rubbers. Properties which Rubber, unvulcanized –Determinations using a shearing – disc
may be determined are the tensile strength, the elongation at break, viscometer – Part 1 : Determination of Mooney viscosity.
the stress at a given stress means of specifying or determining the This Malaysian Standards specifies a method of use of a shearing
yield point are also given. This standard shall replace MS 1157 : Part disc viscometer for measuring the Mooney viscosity of
3 : 1989, Method of test for vulcanized rubber Part 3 : Determination uncompounded or compounded rubbers.
of tensile stress-strain properties. Price RM20
Price RM20
MS ISO 289-2 : 1998
MS ISO 48 : 2002 Rubber, unvulcanized –Determinations using a shearing – disc
Rubber, vulcanized or thermoplastic - Determination of hardness viscometer – Part 2: Determination of pre-vulcanization
(hardness between 10 IRHD and 100 IRHD) characteristics.
This Malaysian Standard specifies four methods for the determination This Malaysian Standards specifies a method for determination the
of the hardness of vulcanized or thermoplastic rubbers on flat pre-vulcanization characteristics of compounded rubber. The pre-
surfaces: vulcanisation characteristics determined by this method provide a
Method N Normal test means of estimating how long compounded rubber can be maintained
Method H High-hardness test at high temperatures and remain processable.
Method L Low-hardness test Price RM10
Method M Microtest
and four methods for the determination of apparent hardness of MS ISO 780 : 2001
curved surfaces using methods, N, H, L and M, respectively: Methods Packaging - Pictorial marking for handling goods
CN, CH, CL and CM. This standard supersedes MS 1157 : Part A1 : This Malaysian Standard specifies a set of symbols conventionally
1995. used for marking of transport packages in their physical distribution
Price RM30 chain to convey handling instructions. The symbols should be used
only when necessary. This Malaysian Standard is applicable to
MS ISO 132 : 2002 packages containing any kind of goods, but does not include
Rubber, vulcanized or thermoplastic - Determination of flex instructions specific to the handling of dangerous goods. This standard
cracking and crack growth (De Mattia) supersedes MS 984 : 1985
This Malaysian Standard specifies a method of test intended for use Price RM20
in comparing the resistance of rubbers to the formation and growth
of cracks, when subjected to repeated flexing on the De Mattia type MS ISO 813 : 1999
machine. For determination of crack growth, an artificial cut is made Rubber, vulcanized or thermoplastic – Determination of adhesion
in the test piece to initiate cut growth. This standard supersedes MS to a rigid substrate – 90 ° peel method
1157 : Part 10 : 1993. Specifies a method for the determination of the adhesive strength of
Price RM20 a vulcanized or thermoplastic rubber bonded to a rigid substrate,
using a test piece comprising a strip of rubber bonded to a single
MS ISO 188 : 2001 plate of rigid material. The method is applicable primarily to test pieces
Rubber, vulcanized or thermoplastic - Accelerated ageing and prepared in the laboratory under standard conditions, such as may
heat resistance tests be used to provide data for the choice of rubber compounds or
This Malaysian Standard specifies accelerated ageing or heat adhesive systems, the development of such materials and the control
resistance tests on vulcanized or thermoplastic rubbers. The methods of manufacturing processes. This method is not suitable for high-
are: Method A: air-oven method using a cell-type oven or cabinet hardness rubbers. This standard identical with ISO 813 : 1997 and it
oven with low air speed and a ventilation of 3 to 10 changes per supersedes MS 1157 : Part 37 : 1991.
hour; Method B: air-oven method using a cabinet oven with forced Price RM20
air circulation by means of a fan and a ventilation of 3 to 10 changes
per hour; and Method C: oxygen pressure method at 2, 1 Mpa and MS ISO 815 : 1998
70°C. This standard supersedes MS 1157 : Part 4 : 1989. Rubber, vulcanised or thermoplastic-Determination of
Price RM20 compression set at ambient, elevated or low temperatures
This Malaysian Standard specifies methods for determination of
MS ISO 247 : 2001 compression set characteristics of vulcanised and thermoplastic
Rubber : Determination of ash rubber at ambient , elevated or low temperatures. The methods are
This Malaysian Standard specifies two methods for the determination intended to measured the ability of rubber of hardness within the
of ash from raw rubbers, compounded rubbers and vulcanizates. range 10 IRHD to 95 IRHD to retain their elastic properties at specified
The methods are applicable to raw, compounded or vulcanized temperature after prolonged compression at constant strain (where
rubbers of the M,N,O,R and U families. This standard supersedes possible 25%) under one of the alternative sets of condition described.
MS 1359 : Part 1 : 1994. For rubber of hardness greater than 80 IRHD, a lower compression
Price RM10 strain is used: 15% for a normal hardness from 80 IRHD to 89 IRHD
and 10% for a nominal hardness from 90 IRHD to 95 IRHD.
Price RM20
6
MS ISO 1431-2 : 1999 MS ISO 2782 : 1999
Rubber, vulcanized or thermoplastic – Resistance to ozone Rubber, vulcanized or thermoplastic - Determination of
cracking - Part 2 : Dynamic strain test permeability to gases.
Specifies a method intended for use in estimating the resistance of Describes two procedures for measuring the permeability of rubber
vulcanized or thermoplastic rubbers to cracking when exposed, under to gases under steady-state conditions. One uses a horizontal
dynamic tensile strain, to air containing a definite concentration of measuring device for measurements at constant pressure and the
ozone and at a definite temperature in circumstances that exclude other uses a vertical measuring device for measurements at constant
the effects of direct light. This standard is identical with ISO 1431-2 : volume or constant pressure. The results obtained by these
1994. procedures may be extrapolated to thicknesses of material different
Price RM20 from that of the test piece providing the rubber is homogeneous and
isotropic. This standard is identical with ISO 2782 : 1995 and it
MS ISO 1432 : 2000 supersedes MS 1157 : Part 15: 1993.
Rubber, vulcanized or thermoplastic – Determination of low Price RM20
temperature stiffening (Gehman test)
Specifies a static procedure, known as the Gehman test, for MS ISO 2921 : 2001
determining the relative stiffness characteristics of vulcanized or Rubber, vulcanized - Determination of low-temperature
thermoplastic rubbers over a temperature to approximately – characteristics - Temperature-retraction procedure (TR test)
150°C. This standard is identical with ISO 1432 : 1988. This Malaysian Standard specifies a method for the determination of
Price RM10 the temperature-retraction characteristics of extended vulcanized
rubber.
MS ISO 1433 : 2000 Price RM10
Rubber, vulcanized - Preferred gradations of properties
Lays down preferred numerical values for the gradation of various MS ISO 3383 : 1998
physical properties of solid vulcanized rubber determined in Rubber-General directions for achieving elevated or subnormal
accordance with standard methods of test. The standard is identical temperatures for test purposes.
with ISO 1433: 1995. Malaysian Standard specifies general requirements for achieving
Price RM20 elevated or subnormal temperatures in the testing of rubber and other
elastometric materials. It specifies general principles of the
MS ISO 1817 : 2002 construction and operating of temperature controlled chambers for
Rubber, vulcanized - Determination of the effect of liquids conditioning and/or testing . For some tests-for example ageing tests-
This Malaysian Standard describes methods of evaluating the special procedures, conditions or equipment which differ from those
resistance of vulcanized thermoset or thermoplastic rubbers to the specified in this Malaysian Standard may be required . In such cases,
action of liquids by measurement of properties of the rubbers before the requirements should be included in the method of test and
and after immersion in test liquids. The liquids concerned include supersede the requirements of this Malaysian Standard.
current service liquids, such as petroleum derivatives, organic Price RM10
solvents and chemical reagents as well as reference test liquids.
This standard supersedes MS 1157 : Part 20 : 1991. MS ISO 3384 : 2002
Price RM30 Rubber, vulcanized or thermoplastic - Determination of stress
relaxation in compression at ambient and at elevated
MS ISO 1853 : 2002 temperatures
Conducting and dissipative rubbers, vulcanized or thermoplastic This Malaysian Standard specifies two methods for determining the
- Measurement of resistivity decrease in counter force exerted by a test piece of vulcanized or
This Malaysian Standard specifies the requirements for the laboratory thermoplastic rubber which has been compressed to a constant
testing of the volume resistivity of specially prepared test pieces of deformation and maintained thus at a predetermined test temperature.
vulcanized or thermoplastic rubber compounds rendered conducting Two forms of test piece are permitted: cylindrical test pieces and
or dissipative by the inclusion of carbon black or ionizable materials. rings. Different shapes and sizes of test piece give different results,
Antistatic properties may also be conferred on rubber materials by and comparison of results should be limited to test pieces of similar
the incorporation of ionizable materials into the rubber mix. The test size and shape. This standard supersedes MS 1157 : Part 32 : 1991.
is suitable for materials with a resistivity of less than 1010 Wm. Price RM20
Price RM20
MS ISO 3865 : 1999
MS ISO 2285 : 1999 Rubber, vulcanized or thermoplastic – Methods of test for
Rubber, vulcanized or thermoplastic – Determination of tension staining in contact with organic material
set at normal and high temperatures Specifies three methods for estimating the staining of organic finishes
Specifies a method for determining the tension set characteristics of 9in the following called ‘organic material’) by vulcanized or
vulcanized or thermoplastic rubbers. The test is intended to measure thermoplastic rubber:- method A: contact and migration stain;-
the ability of rubbers of hardness within the range 30 to 94 method B: extraction stain;- method C: penetration stain; as defined
International Rubber Hardness Degrees (IRHD) to retain their elastic in clause 3. This standard is identical with ISO 3865 : 1997.
properties after extension, at a standard temperature to a specified Price RM20
strain which is maintained for a specified time at the same or at a
specified higher temperature and then released at the standard MS ISO 4648 : 1998
temperature. This standard is identical with ISO 2285 : 1988 and it Rubber, vulcanised or thermoplastic – determination of
supersedes MS 1157 : Part 2 : 1989. dimensions of test pieces and product for test purposes.
Price RM10 Malaysian Standard specifies 4 methods for the measurement of the
dimensions of solid vulcanised or thermoplastic rubber test pieces
MS ISO 2393 : 2000 or products for test purposes, three contact methods, designated
Rubber test mixes - Preparation, mixing and vulcanization - A,B and C and one non-contact method designated D. The method
Equipment and procedures to be used is selected according to the magnitude of the dimension
Specifies the equipment and procedures for the preparation, mixing to be measured and to be desired accuracy.
and vulcanization of test mixes, as specified in the rubber evaluation
procedures. This standard is identical with ISO 2393 : 1994.
Price RM20
7
Method A – for dimension less than 30mm MS ISO 11346 : 1999
Method B - for dimension less than 30mm and up to and including Rubber, vulcanized or thermoplastic – Estimation of life-time
100mm and maximum temperature of use from an arrhenius plot
Method C – for dimension over 100 mm Describes the principles and procedures for estimating the life-time
Method D – non-contact procedure for all dimensions and maximum temperature of use of vulcanized or thermoplastic
Price RM10 rubbers, using an Arrhenius plot. This method is suitable for different
tests on rubber, but for tests under stress or deformation (creep,
MS ISO 4661-1 : 1998 relaxation, etc.) physical (viscoelastic) changes of material cannot
Rubber, vulcanised or thermoplastic – Preparation of samples easily be separated from any chemical change. Then the Arrhenius
of samples and test pieces- Part 1 : Physical tests. equation is no longer the only possible model, and the Willams,
This Malaysian Standard specifies methods of preparing test pieces Landel, Ferry (WLF) equation may be more suitable to represent the
from vulcanised and thermoplastic rubber for use in physical tests change in the material as a function of time. This standard is identical
on rubber specified in other Malaysia Standards. with ISO 11346 : 1997.
MS ISO 4665 : 2002

Rubber, vulcanized and thermoplastic - Resistance to weathering 83.080 Plastics
This Malaysian Standard specifies methods for the exposure of rubber
materials to natural or artificial weathering and methods for the
determination of changes in colour, appearance and physical
properties resulting from exposure. MS 1440 : 1998
Price RM20 Glossary of terms for plastics
This Malaysian Standard defines terms used in plastic industry. The
MS ISO 6471 : 2000 terms are listed alphabetically.
Rubber, vulcanized – Determination of crystallization effects Price RM150
under compression
Specifies a method for the determination of the tendency of vulcanized MS 1501 : 2000
rubbers to crystallization, by measurement of the recovery of Method of test for measuring shrinkage from mould dimensions
compressed test pieces. This standard is identical with ISO 6471 : of moulded plastics
1994. Intended to measure batch to batch uniformity in initial shrinkage
Price RM20 from mould to moulded dimensions of eiher thermoplastic or
thermosetting materials when moulded by compression, injection or
MS ISO 7619 : 2000 transfer under specified conditions. This test method does not provide
Rubber – Determination of indentation hardness by means of for the measurement of shrinkages that may occur as moulded
pocket hardness meters materials age, after the first 48 hours out of the mould.
Specifies a method for the determination of the indentation hardness Price RM30
of rubber by means of pocket hardness meters
of two types: a) the Shore-type durometer; b) a meter calibrated in MS ISO 489 : 1998
IRHD. This standard is identical with ISO 7619 : 1997 and it Plastics – Determination of the refractive index of transparent
supersedes MS 1157 : Part 17 : 1993. plastics
Price RM20 This standard specifies two methods of test for determining the
refractive index of transparent plastics, namely
MS ISO 8013 : 2005 Method A : Refractometric method for measuring the refractive index
Rubber, vulcanized – Determination of creep in compression or of transparent cast, moulded or sheet materials by means of a
shear refractometer,
This standard specifies a method for the determination of creep in Method B : Immersion method for determining the refractive index
rubber continuously subject to compressive or to shear forces. The of powdered or granulated transparent materials by means of a
standard cannot be used for intermittent deformation of rubber. microscope and making use of the Becke line phenomenon.
MS ISO 8789 : 2005 MS ISO 844 : 1998

Rubber hoses and hose assemblies for liquefied petroleum gas Cellular plastics – Compression test for rigid materials
in motor vehicle – Specification This standard specifies a method of test for determining the
This Malaysian Standard specifies the requirements for rubber hoses compressive strength and corresponding relative deformation or the
and hose assemblies, up to a maximum bore of 20 mm, for use in compressive stress at 10 % relative deformation of rigid cellular
motor vehicles with liquefied petroleum gas (LPG) installations. The plastics.
hoses are designed for use up to a maximum pressure 2,5 MPa (25 Price RM20
o o
bar) and a working temperature between - 40 C and + 80 C.
Price RM90 MS ISO 877 : 2001
Plastics - Methods of exposure to direct weathering, to
MS ISO 9026 : 1998 weathering using glass-filtered daylight, and to intensified
Raw rubber or unvulcanized compounds – Determination of weathering by daylight using Fresnel mirrors
green strength This Malaysian Standard specifies methods of exposing plastics to
This Malaysian Standards specifies a method for the determination solar radiation, either by direct exposure to natural weathering
of green strength of raw rubber or unvulcanized–rubber compounds (Method A), to indirect solar radiation by modification of its spectral
using a tensile stress –strain test, the test pieces being prepared distribution with glass to simulate ageing of plastics behind building
following standard test condition, or cut from calendered sheets. or automotive window glass (Method B), or to solar radiation intensi-
Price RM20 fied by the use of Fresnel mirrors to achieve acceleration of the
weathering processes (Method C). The purpose is to assess changes
produced after specified stages of such exposures.
Price RM30
8
MS 1371 : 1995
Methods of test for environmental stress - cracking of ethylene
plastics.
83.080.01 Plastics in general This Malaysian Standard specifies methods for the determination of
the susceptibility of ethylene plastics to environmental stress -
cracking when subjected to certain condition. Under certain conditions
MS 1271 : 1992 of stress and in the presence of environments such as soaps, wetting
Method of test for plastics : Determination of hardness : Shore agents, oils or detergent, ethylene plastics may exhibit mechanical
hardness. failure by cracking.
This Malaysian Standard specifies a method for the determination of Price RM20
the indentation hardness of plastics by means of durometers of two
types durometer type A is used for softer materials and durometer MS 1406 : 1996
type D used for harder materials (see the note in clause 7.2 of the Code of practice for system of tolerances for the dimension of
standard). The method permits measurement either of the initial plastics moulding.
indentation or of the indentation after a specified period of time, or This code of practice recommends a system of tolerances for
both. dimensions of plastics mouldings produced from thermoplastics and
Price RM10 thermosetting moulding materials by compression moulding, transfer
moulding or injection moulding.
MS 1272 : Part 1 : 1993 Price RM20
Method of test for plastics : Determination of hardness : Part 1
: Ball indentation method. MS 1421 : 2005
This Part of the standard specifies a method for determining the Test method for haze and luminous transmittance of transparent
hardness of plastics and ebonite by means of a loaded ball indenter. plastics (First revision)
The ball indentation hardness determined by this method may provide This Malaysian Standard covers the evaluation of specific light-
data for research and development, quality control and acceptance transmitting and wide-angle-light-scattering properties of planner
or rejection under specifications. sections of materials such as essentially transparent plastic. Two
Price RM10 procedures are provided for the measurement of luminous
transmittance and haze.
MS 1272 : Part 2 : 1992 Price RM40
Method of test for plastics : Determination of hardness : Part 1
: Rockwell hardness. MS 1441 : 1998
This Part of standard specifies a method for determining the Method of test for seal strength of flexible barrier materials.
indentation hardness of plastics by means of the Rockwell hardness This test method covers the measurement of the seal strength of
tester using the Rockwell M, L and R hardness scales. flexible barrier materials.
MS 1274 : 1992 MS 1442 : 1998

Method of test for plastics : Determination of temperature of Methods of test for the assessment of carbon black dispersion
deflection under load. in polyethylene using a microscope.
This standard specifies two methods for the determination of These methods describe procedures for assessing the uniformity of
temperature of deflection under load (bending stress) of plastics: the dispersion of carbon black in a compound, Extrusion or moulded
- Method A using a nominal surface stress of 1.80 MPa; article.
- Method B using a nominal surface stress of 0.45 MPa. Price RM10
Price RM20
MS 1465 : Part 1 : 1999
MS 1345 : 1993 Method of test for determination of plastics resistivity : Part 1 :
Method of test for plastics – Determination of tensile creep. Surface resistivity
This standard specifies a method for the determination of tensile Specifies a method for determining the electrical surface resistivity
creep of rigid plastic materials in the form of test specimens such as of plastics from the current flowing between two electrodes mounted
those employed for the determination of tensile properties, moulded on the surface of the material when a voltage is applied between
directly or cut from sheets. them. Procedures with various types of apparatus are described. All
Price RM20 procedures enable the operator to determine surface resistivity when
residual charge is negligible. One procedure, using a circuit shown
MS 1349 : 1994 in Figure 5, facilitates the determination of significant residual charge.
Method of test for plastics – Determination of flexural properties The method is suitable for materials with a range of surface resistivity
of rigid plastics. levels of 108 W or greater. The range of applicability may be extended
This Malaysian Standard specifies a method for the determination of by the used of appropriate electrode systems and measuring devices.
flexural properties of rigid non-reinforced and fibre-reinforced plastic Price RM20
materials, in the form of rectangular bars of standard on non-standard
dimensions, moulded directly or cut from sheets or other shapes. It
applies only to a simple, freely supported beam, loaded at mid-span.
Price RM20
9
MS 1465 : Part 2 : 1999 MS 1476 : 1999
Method of test for determination of plastics resistivity : Part 2 : Method of test for determining the carbon dioxide loss of plastics
Volume resistivity beverage containers
Specifies a method for determining the electrical volume resistivity Specifies a method for determining the carbon dioxide (CO2) loss
of plastics from the current flowing through the material when a voltage from plastics beverage containers after a specified period of storage
is applied to the opposite faces of a sheet of the material. The method time. Factors contributing to this pressure loss are volume expansion
is unsuitable when the volume resistivity is below 107 W cm. Lower and the gas transport characteristics of the package including
values should be measured by the method given in BS 2044. permeation and leakage.
MS 1466 : 1999 MS 1808 : 2005

Method of test for linear thermal expansion of solid materials Test method for indentation hardness of rigid plastics by means
by thermomechanical analysis of a Barcol Impressor
Specifies a method for the determination of linear thermal expansion This Malaysian Standard covers the determination of indentation
of solid materials using thermomechanical analysis techniques. This hardness of both reinforced and non-reinforced rigid plastics using a
test method is applicable to solid materials that exhibit sufficient rigidity Barcol Impressor, Model No. 934-1 and Model No. 935.
over the test temperature range such that the sensing probe does Price RM40
not produce indentation of the specimen and is applicable to the
temperature range from – 120°C to 600°C. The temperature MS ISO 60 : 2004
range may extended depending upon the instrumentation and Plastics – Determination of apparent density of material that
calibration materials used. can be poured from a specified funnel
Price RM20 This standard specifies a method of determining the apparent density,
i.e. the mass per unit of volume of loose material (powdered or
MS 1467 : 1999 granular material) that can be poured from a funnel of specified
Method of test for determination of 2 % secant modulus for design. Price RM10
polyethylene films
Specifies a method for calculating the 2 % secant modulus for MS ISO 62 : 2001
polyethylene film less than 1.0 mm in thickness. This standard will Plastics - Determination of water absorption
facilitate modulus comparisons of similar materials by standardising This Standard describes procedures for determining the amount of
the method for deriving the points on the stress-strain curve from water absorbed by plastic specimens of defined dimensions, when
which the calculations are performed. immersed in water or when subjected to humid air under controlled
Price RM10 conditions. The “through-the-thickness” moisture diffusion coefficient
can be determined for single-phase material by assuming Fickian
MS 1468 : 1999 diffusion behaviour with constant moisture absorption properties
Method of test for determining the 24-hour gas (air) space through the thickness of the test specimen.
acetaldehyde content of freshly blown polyethylene Price RM20
terephthalate (pet) bottles
Specifies a method for determining the 24 h gas-space acetaldehyde MS ISO 75-1 : 1999
(AA) content of freshly blown polyethylene terephthalate (PET) Plastics – Determination of temperature of deflection under load
bottles. The test method, containing internal or external standard - Part 1 : General test method
calibration, is applicable to all PET bottles. Specifies methods for the determination of the temperature of
Price RM20 deflection under load (bending stress under three-point loading) of
different types of material. The methods specified are suitable for
MS 1469 : 1999 assessing the behaviour of the different types of material at elevated
Specification for plastic lenses for automotive lamps temperature under load at a specified rate of temperature increase.
Prescribes the specifications for the plastic lenses for automotive This standard is identical with ISO 75-1 : 1993.
lamps. It does not specify the complete lamps. Price RM10
Price RM10
MS ISO 75-2 : 1999
Plastics – Determination of temperature of deflection under load
MS 1470 : 1999
- Part 2 : Plastics and ebonite
Specification for PVC floor mats for motor vehicles
Specifies three methods for the determination of the temperature of
Prescribes the specifications for floor mats made of PVC intended
deflection under load (bending stress) of plastics and ebonite:
for use in motor vehicles.
- method A, using a nominal surface stress of 1.80 MPa;
Price RM10
- method B, using a nominal surface stress of 0.45 MPa;
- method C, using a nominal surface stress of 8.00 MPa.
MS 1473 : 1999
This standard is identical with ISO 75-2 : 1993.
Method of test for measuring the dynamic mechanical properties
Price RM10
of plastics using three point bending
Specifies the use of dynamic mechanical instrumentation for gathering
MS ISO 75-3 : 1999
and reporting the viscoelastic properties of thermoplastic and
Plastics – Determination of temperature of deflection under load
thermosetting resins and composite systems in the form of rectangular
- Part 3 : High-strength thermosetting laminates and long-fibre-
bars moulded directly or cut from sheets, plates, or moulded shapes.
reinforced plastics
The data generated, using three-point bending techniques, may be
Specifies a method for the determination of the temperature of
used to identify the thermomechanical properties of plastics material
deflection under load (bending stress) of high-strength thermosetting
or composition using a variety of dynamic mechanical instruments.
laminates and compression-moulded long-fibre-reinforced plastics.
The standard is valid for a wide range of frequencies, typically from
The test load used is not a fixed load, as in part 2 of this International
0.01 Hz to 100 Hz.
Standard, but a function (1/10) of the ultimate or specified load. This
Price RM10 allows the method to be applied to materials with a wide range of
strengths and bending moduli. This standard is identical with ISO
75-3 : 1993.
Price RM10
10
MS ISO 175 : 2001 MS ISO 291 : 2000
Plastics - Methods of test for the determination of the effects of Plastics - Standard atmospheres for conditioning and testing
immersion in liquid chemicals Sets out specifications relating to the conditioning and testing of all
This Malaysian Standard specifies a method of exposing test plastics and all types of test specimens at constant atmospheric
specimens of plastic materials, free from all external restraint, to liquid conditions which correspond to the average atmospheric conditions
chemicals, and methods for determining the changes in properties in laboratories. This standard supersedes MS 1346 : 1993.
resulting from such immersion. This standard supersedes MS 1341 Price RM20
: 1993.
Plastics - Determination of thermal stability of poly (vinyl
MS ISO 176 : 2001 chloride), related chlorine-containing homopolymers and
Plastics - Determination of loss of plasticizers - Activated carbon copolymers and their compounds - Discoloration method
method. This Malaysian Standard specifies two methods for the determination
This Malaysian Standard specifies two empirical methods for the of the thermal stability of products and compounds based on vinyl
quantitative determination of the loss of mass from a plastic material chloride homopolymers and copolymers (referred to simply as PVC
under defined conditions of time and temperature, in the presence of in the following text) by the extent of the discoloration that occurs
activated carbon. when they are exposed, in the form of sheet, to elevated temperatures.
Price RM10 - Method A : Oil-bath method
- Method B : Oven
Plastics - Determination of migration of plasticizers
This Malaysian Standard specifies a method for the determination of MS ISO 489 : 1998
the tendency of plasticizers to migrate from plastics in which they Plastics – Determination of the refractive index of transparent
are contained into other materials or other plastics when they are plastics
brought into close contact. This standard specifies two methods of test for determining the
Price RM10 refractive index of transparent plastics, namely
Method A : Refractometric method for measuring the refractive index
MS ISO 178 : 2004 of transparent cast, moulded or sheet materials by means of a
Plastics – Determination of flexural properties refractometer, Method B : Immersion method for determining the
This Malaysian standard specifies a method for determining the refractive index of powdered or granulated transparent materials by
flexural properties of rigid and semi-rigid plastics under defined means of a microscope and making use of the Becke line
conditions. A standard test specimen is defined, but parameters are phenomenon.
included for alternative specimen sizes for use where appropriate. A Price RM10
range of test speeds in included.
Price RM30 MS ISO 527 : Part 1 : 1994
Plastics – Determination of tensile properties: Part 1: General
MS ISO 179-1 : 2002 principles.
Plastics - Determination of Charpy impact properties - Part 1 : This Malaysian Standard specifies the test general principles for
Non-instrumented impact test determining the tensile properties of plastics and plastic composites
This Malaysian Standard specifies a method for determining the under defined conditions. Several different types of test specimen
Charpy impact strength of plastics under defined conditions. A are defined to suit different types of material which are detailed in
number of different types of specimen and test configurations are subsequent parts of this Malaysian Standard.
defined. Different test parameters are specified according to the Price RM20
type of material, the type of test specimen and the type of notch.
Price RM30 MS ISO 527 : Part 2 : 1994
Plastics – Determination of tensile properties: Part 2 : Test
MS ISO 179-2 : 2002 conditions for moulding and extrusion plastics.
Plastics - Determination of Charpy impact properties - Part 2 : This Malaysian Standard specifies the test conditions for determining
Instrumented impact test the tensile properties of moulding and extrusion plastics, based upon
This Malaysian Standard specifies a method for determining Charpy the general principles.
impact properties of plastics from force-deflection diagrams. Different Price RM10
types of rod-shaped test specimen and test configuration, as well as
test parameters depending on the type of material, the type of test MS ISO 604 : 2003
specimen and the type of notch are defined in part 1 of ISO 179. Plastics – Determination of compressive properties
Dynamic effects such as load-cell/striker resonance, test specimen This Malaysian Standard specifies a method for determining the
resonance and initial-contact/inertia peaks are described (see Figure compressive properties of plastics under defined conditions. A
1, curve b, and Annex A). standard test specimen is defined but its length may be adjusted to
Price RM30 prevent buckling under load from affecting the results. A range of
test speeds is included. The method applies to the following range of
MS ISO 180 : 2002 materials:
Plastics - Determination of Izod impact - rigid and semi-rigid [1] thermoplastic moulding and extrusion
This Malaysian Standard specifies a method for determining the Izod materials, including compounds filled and reinforced by e.g.
impact strength of plastics under defined conditions. A number of short fibres, small rods, plates or granules in addition to
different types of specimen and test configurations are defined. unfilled types; rigid and semi-rigid thermoplastic sheet;
Different test parameters are specified according to the type of - rigid and semi-rigid thermoses moulding materials, including
material, the type of test specimen and the type of notch. The method filled and reinforced compounds; rigid and semi-rigid
is used to investigate the behaviour of specified types of specimen thermoses sheet;
under the impact conditions defined and for estimating the brittleness - thermotropic liquid-crystal polymers.
or toughness of specimens within the limitations inherent in the test Price RM30
conditions. This standard supersedes MS 1270 : 1992.
Price RM20
11
MS ISO 844 : 1998 MS ISO 1043-3 : 2004
Cellular plastics – Compression test for rigid materials Plastics – Symbols and abbreviated terms : Part 3 : Plasticizers
This standard specifies a method of test for determining the (First revision)
compressive strength and corresponding relative deformation or the
This Malaysian Standard gives uniform symbols for components of
compressive stress at 10 % relative deformation of rigid cellular
terms relating to plasticizers to form abbreviated terms. It includes,
plastics.
in general, only those abbreviated terms that have come into
Price RM20
established use. The purpose of this Malaysian Standard is to prevent
the occurrence of more than symbol for a given plasticizers.
MS ISO 868 : 2004
Price RM20
Plastics and ebonite – Determination of indentation hardness
by means of a durometer (Shore hardness)
MS ISO 1043-4 : 2004
This standard specifies a method for the determination of the indention
Plastics – Symbols and abbreviated terms – Part 4 : Flame
hardness of plastics and ebonite by means of durometers of two
retardants
types: type A is used for softer materials and type D for harder
This Malaysian Standard provides uniforms symbols for flame
materials. The method permits measurement either of the initial
retardants added to plastics materials. The symbols are written with
indentation or of the identation after a specified period of time, or
the abbreviated term ”FR” and one or more succeeding code numbers
both.
are given in clause 5.
Price RM20
Price RM10
MS ISO 899-1 : 1999
MS ISO 1183 : 1995
Plastics – Determination of creep behaviour - Part 1 : Tensile
Plastics - Methods for determining the density and relative
creep
density of non-cellular plastics.
Specifies a method for determining the tensile creep of plastics in
This standard specifies four methods for the determination of the
the form of standard test specimens under specified conditions such
density and relative density of non-cellular plastics in the from of
as those of pretreatment, and humidity. This standard is identical
sheet, film, tube, moulded objects, and moulding powders, granules
with ISO 899-1 : 1993.
and pellets. The methods including immersion, pyknometer, titration
Price RM20
and density gradient column method.
Price RM20
MS ISO 899-2 : 1999
Plastics – Determination of creep behaviour - Part 2 : Flexural
MS ISO 1210 : 1995
creep by three-point loading
Plastics - Determination of the burning behaviour of horizontal
Specifies a method for determining the flexural creep of plastics in
and vertical specimens in contact with a small flame ignition
the form of standard test specimens under specified conditions such
source.
as those of pretreatment, temperature and humidity. It applies only
This standard specifies a small scale laboratory screening procedure
to a simple freely supported beam loaded at mid-span (three-point-
for comparing the relative burning behaviour of vertically or
loading test). This standard is identical with ISO 899-2 : 1993.
horizontally oriented platic specimens exposed to a small-flame
Price RM20
ignition source. This method of test determines the afterflame/
afterglow times and damaged length of specimens.
Plastics – Determination of the brittleness temperature by impact
This Malaysian Standard is identical with ISO 974:2000. This MS ISO/R 1326 : 1995
Malaysian Standard specifies a method for the determination of the Plastics - Determination of flammability and burning rate of
temperature at which plastics that are not rigid at normal ambient plastics in the form of film.
temperature exhibit brittle failure under specified impact conditions. This standard describes a method for determining the relative
The method utilises a statistical technique to quantify the brittleness flammability and the burning rate of plastics in the form of sheets or
failure temperature. It establishes the temperature at which there is films of thickness between 1.5 mm and 0.05 mm. This method
a 50 % chance of failure in either unnotched or notched specimens. provides a means of comparing the flammability of plastics in sheet
Price RM20 or film form.
Price RM10
MS ISO 1043-1 : 2004
Plastics – Symbols and abbreviated terms : Part 1 : Basic MS ISO 1628-1 : 2004
polymers and their special characteristics (First revision) Plastics – Determination of the viscosity of polymers in dilute
This Malaysian Standard gives uniform abbreviated terms for plastics solution using capillary viscosmeters – Part 1: General principles
and symbols for components of these terms. It includes only those This standard defines the general conditions for the determination of
abbreviated terms that have come into established use, and its aim the reduced viscosity, intrinsic viscosity and K-Value of organic
is both to prevent the occurrence of more than one symbol for a polymers in dilute solution. It defines the standard parameters that
given plastics term, and to prevent the interpretation of more than are applied to viscosity measurement, and can be used to develop
one meaning for a given symbol. standards for measuring the viscosities in solution of individual types
Price RM20 of polymer. It can also be used to measure and report the viscosities
of polymers in solution for which no separate standards exist.
MS ISO 1043-2: 2004 Price RM30
Plastics - Symbols and abbreviated terms: Part 2 : Fillers and
reinforcing materials (First revision) MS ISO 1628-2 : 2004
This Malaysian Standard provides uniform symbols for terms referring Plastics – Determination of the viscosity of polymers in dilute
to fillers and reinforcing materials. It includes only those symbols solution using capillary viscosmeters – Part 2: Poly(vinyl
that have come into established use, and its aim is both to prevent chloride) resins
the occurrence of more than one symbol for a given filler or reinforcing This standard specifies conditions for the determination of the reduced
materials, and to prevent the interpretation of a given symbol in more viscosity (also known as viscosity number) and K-value of PVC resins.
than one way. It is applicable to resins in powder form which consist
Price RM10
12
of homo-polymers of the monomer vinyl chloride and copolymers, MS ISO 3167 : 2003
terpolymers, etc., of vinyl chloride with one or more other monomers, Plastics – Multipurpose test specimens
but where vinyl chloride is the main constituent. The resins may This Malaysian Standard specifies requirements relating to
contain small amount of unpolymerised substances (e.g. emulsifying multipurpose test specimens for plastic moulding materials intended
or suspending agents, catalyst residues, etc.) and other substances for processing by injection or direct compression moulding.
added during the course of the polymerisation Specimens of types A and B are tensile test specimens from which,
Price RM20 with simple machining, specimens for a variety of other tests can be
taken (see Annex A). Because they have such wide utility, these
MS ISO 1675 : 1995 tensile specimens are referred to in this International Standard as
Plastics - Liquid resins - Determination for density and relative multipurpose test specimens. This standard supersedes MS ISO
density by pyknometer method. 3167: 2000.
This standard specifies a method for the determination of the density Price RM20
of liquid resins using a pyknometer of known volume.
Plastics - Determination of changes in colour and variations in
MS ISO 1798 : 1998 properties after exposure to daylight under glass, natural
Flexible cellular polymeric materials-Determination of tensile weathering or laboratory light sources (First revision)
strength and elongation break. Describes procedures used to determine changes in colour and other
This Malaysian Standard specifies a method for determining the appearance properties, and variations in mechanical or other
strength and deformation properties of flexible cellular materials when properties, of plastics that have been exposed to daylight behind
a test piece is extended at a constant rate until it breaks. glass, natural weathering or light from a laboratory source. The
Price RM10 procedure used to analyse data depends on whether the test used
to characterize the materials being exposed is destructive or non-
MS ISO 2039-1 : 2004 destructive. The exposures are conducted under conditions described
Plastics – Determination of hardness – Part 1: Ball indention in specific exposure standards. This standard supersedes MS ISO
method 4582 : 1995
This standard specifies a method for the determining the hardness Price RM30
of plastics and ebonite by means of a loaded ball indenter.
Price RM20 MS ISO 4589-1 : 2000
Plastics – Determination of burning behaviour by oxygen index
MS ISO 2555 : 1995 – Part 1 : Guidance
Plastics - Resins in the liquid state or as emulsions or Constitutes s guidance document for the OI test. It provides
dispersions - Determination of apparent viscosity by the information to guide the reader in the use of the test procedures
Brookfield test method. described in parts 2 and 3. This standard is identical with ISO 4589-
This standard specifies a method of determining an apparent viscosity, 1 : 1996. Price RM20
by the Brookfield test method, of resins in a liquid or similar state,
using one of the types of rotational viscometer described in this MS ISO 4607 : 1995
standard. Plastics – Method of exposure to natural weathering.
Price RM20 This standard describes procedures for exposing plastics to natural
weathering in order to assess changes produced after specified
MS ISO 2578 : 1995 stages of such exposure.
Plastics - Determination of time temperature limits after Price RM20
prolonged exposure to heat.
This standard specifies the principles and procedures for evaluating MS ISO 4892-1 : 1998
the thermal endurance properties of plastics exposed to elevated Plastics - Methods of exposure to laboratory light sources : Part
temperature for long periods. 1 : General Guidance.
Price RM30 This Malaysian Standard provides information and general guidance
relevant to the selection and operation of the methods of exposure
MS ISO 2818 : 1995 described in detail in subsequent parts.
Plastics Preparation of test specimens by machining. Price RM20
This standard establishes the general principles and procedures to
be followed when machining and notching test specimens from MS ISO 4892-2 : 1998
compression-moulded and injection-moulded plastics, extruded Plastics-Methods of exposure to laboratory light sources –Part
sheets, plates and partially finished or wholly finished products. 2 : Xenon-arc sources.
Price RM20 This Malaysian Standard specifies method for exposing specimens
to xenon-arc light sources.
Plastics – Determination of melting behaviour (melting
temperature or melting range) of semi-crystalline polymers by MS ISO 4892-3 : 1998
capillary tube and polarizing-microscope methods (First Plastics-Methods of exposure to laboratory light sources –Part
revision) 3 : Fluorescent UV lamps.
This standard specifies two methods for evaluating the melting This Malaysian Standard specifies method for exposing specimens
behaviour of semi-crystalline polymers. Method A: Capillary tube. to different types of fluorescent UV lamp.
This method is based on the changes in shape of the polymer. It is Price RM20
applicable to all semi-crystalline polymers and their compounds.
Method B: Polarizing microscope. This method is based on changes MS ISO 4892-4 : 1998
in the optical properties of the. It is applicable to polymers containing Plastics-Methods of exposure to laboratory light sources –Part
a birefringent crystalline phase. 4 : Open flame carbon-arc lamps.
Price RM20 This Malaysian Standard specifies method for exposing specimens
to open flame carbon-arc lamps.
Price RM20
13
MS ISO 6252 : 1999 identical with ISO 11357-1 : 1997.
Plastics – Determination of environmental stress cracking (esc) Price RM20
– Constant-tensile-stress method
Specifies methods for the determination of environmental stress MS ISO 11357-2 : 2003 Plastics – Differential scanning
cracking (ESC) of plastics when they are subjected to a constant calorimetry (DSC) – Part 2: Determination of glass transition
tensile force in the presence of chemical agents. It is applicable to temperature
test specimens prepared by moulding and/or machining and can be This Malaysian Standard specifies a method for the determination of
used both for the assessment of ESC of plastics materials exposed the characteristic glass transition temperatures of amorphous and
to different environments, and for the determination of ESC of different semi-crystalline plastics.
plastics materials exposed to a specific environment. This standard Price RM20
is identical with ISO 6252 : 1992.
Price RM20 MS ISO 11357-3 : 2003
Plastics – Differential scanning calorimetry (DSC) – Part 3:
MS ISO 6427 : 1997 Determination of temperature and enthalpy of melting and
Plastics – Determination of matter extractable by organic crystallization.
solvents (Conventional method) This Malaysian Standard specifies a method for the determination of
This standard specifies method for the determination of components the temperature and enthalpy of melting and crystallization of
in plastic that can be extracted by hot organics liquids near their crystalline or semi-crystalline plastics.
boiling points. The extractable components can be monomers, Price RM20
polymers, plasticizers, stabilizers, etc. The kind and percentage of
extractable matter influence the properties of plastics. MS ISO 11357-5 : 2004
Price RM20 Plastics – Differential scanning calorimetry (DSC) – Part 5 :
Determination of characteristic reaction-curve temperatures and
MS ISO 6603-1 : 2003 times, enthalpy of reaction and degree of conversion
Plastics – Determination of puncture impact behaviour of rigid This standard specifies a method for the determination of reaction
plastics – Part 1: Non-instrumented impact testing temperatures and times, enthalpies of reaction and degrees of
This Malaysian Standard specifies methods for the determination of conversion using differential scanning calorimetry (DSC). The method
puncture-impact properties of rigid plastics in the form of flat test applies to monomers, prepolymers in the solid or liquid state. The
specimens, such as discs or square pieces, under defined conditions. material may contain fillers and/or initiators in the solid or liquid state
Specimens may be moulded directly, cut from sheets or taken from Price RM20
finished products. Different types of test specimens and test conditions
are defined. MS ISO 11357-6 : 2004
Price RM30 Plastics – Differential scanning calorimetry (DSC) – Part 6 :
Determination of oxidation induction time
MS ISO 6603-2 : 2003 This standard specifies a method for the determination of the
Plastics - Determination of puncture impact behaviour of rigid oxidation-induction time (OIT) of polymeric materials by differential
plastics – Part 2: Instrumented impact testing scanning calorimetry (DSC). It is applicable to polyolefin resins that
This Malaysian Standard specifies methods for the determination of are in a fully stabilised/compounded form, either as raw materials or
puncture-impact properties of rigid plastics in the form of flat test as finished products. It may be applicable to other plastics.
specimens, using instruments for measuring force and deflection. It Price RM20
is applicable if a force-deflection or force-time diagram, recorded at
a nominally constant striker velocity, is necessary for detailed MS ISO 11357-7 : 2004
characterization of the impact behaviour. Plastics – Differential scanning calorimetry (DSC) – Part 7 :
Price RM30 Determination of crystallization kinetics
This standard specifies two methods, isothermal and non-isothermal,
MS ISO 7111 : 1998 for studying the crystallization kinetics of partially crystalline polymers
Plastics- Thermogravity of polymers – Temperature scanning using differential scanning calorimetry (DSC). It is only applicable to
method. melted polymers.
This Malaysian Standard defines the general conditions for making Price RM20
thermogravimetric measurements on polymers.
Price RM10 MS ISO 13468-1 : 2004
Plastics – Determination of the total luminous transmittance of
MS ISO 8256 : 1999 transparent materials – Part 1: Single-beam instrument
Plastics – Determination of tensile-impact strength This standard covers the determination of the total luminious
Specifies two methods for the determination of the energy required transmittance, in the visible region of the spectrum, of planar
to rupture test specimens of plastics under a specified tensile-impact transparent and substantially colourless plastics, using a single-beam
velocity. The tests can be described as tensile tests at comparatively photometer with a specified CIE standard light source and
high rates of straining. Different parameters are specified depending photodetector. This standard cannot be used for plastics which contain
on the type of test specimen (see 6.1 and figure 3). This standard is flluorecent materials. This standard is applicable to transparent
identical with ISO 8256 : 1990. moulding materials, films and sheets not exceeding 10 mm in
Price RM30 thickness.
Price RM20
MS ISO 11357-1 : 1999
Plastics – Differential scanning calorimetry (DSC) – Part 1 : MS ISO 13468-2 : 2004
General principles Plastics – Determination of the total luminous transmittance of
Specifies a method for the thermal analysis of polymers such as transparent materials – Part 2: Double-beam instrument
thermoplastics and thermosetting plastics, including moulding This standard covers the determination of the total luminous
materials and composite materials, using differential scanning trasmittance, in the visible region of the spectrum, of planar
calorimetry (DSC). Various determinations can be made on polymers transparent and substantially collourless plastics, using a double-
by using differential scanning calorimetry. These determinations are
dealt with in parts 2 to 7 of this standard. This standard is
14
beam scanning spectro-photometer. This standard cannot be used The average molecular mass and the molecular mass distribution
for plastics whuch contain fluorescent materials. This standard is are calculated using a universal calibration curve instead of the
applicable to transparent moulding materials, films and sheets not conventional calibration curve.
exceeding 10 mm in thickness. Price RM20
Price RM20
MS ISO 16014-3 : 2004
MS ISO 13586 : 2003 Plastics – Determination of average molecular mass and
Plastics – Determination of fracture toughness (GIC KIC) – Linear molecular mass distribution of polymers using size-exclusion
elastics fracture mechanics (LEFM) approach chromatography – Part 3: Low-temperature method
This Malaysian Standard is identical with ISO 13586:2000. This This standard specifies a method for determining the average
Malaysian Standard specifies the principles for determining the molecular mass and the molecular mass distribution of polymers by
fracture toughness plastics in the crack-opening mode (mode I) under size-exclusion chromatography (SEC) using an organic eluent at a
defined conditions. Two test methods with cracked specimens are temperature lower than 60 °C. The average molecular mass and the
defined, namely three-point-bending tests and compact-specimen molecular mass distribution are calculated from a calibration curve
tensile tests in order to suit different types of equipment available or constructed using polymer standards.
different types of materials. Price RM20
Price RM30
MS ISO 16014-4 : 2004
MS ISO 14782 : 2004 Plastics – Determination of average molecular mass and
Plastics – Determination of haze for transparent materials molecular mass distribution of polymers using size-exclusion
This standard specifies a method for the measurement of haze, an chromatography – Part 4: High-temperature method
optical property resulting from wide-angle scattering of light, in This standard specifies a method for determining the average
transparent and substantially colourless plastics. This method is molecular mass and the molecular mass distribution of polymers by
applicable to the measurement of haze values of less than 40 %. size-exclusion chromatography (SEC) using an organic eluent at a
Price RM20 temperature between 60 °C and 180 °C. The average molecular mass
and the molecular mass distribution are calculated from a calibration
MS ISO 15512 : 2004 curve constructed using polymer standards.
Plastics – Determination of water content Price RM20
This standard specifies methods for the determination of the water
content of plastics in the form of granules and finished articles.The MS ISO 17281 : 2004
methods are suitable for the determination of water content as low Plastics – Determination of fracture toughness (GIC and KIC) at
as the following levels: Method A (0.1 % or better); Method B (0.01 % moderately high loading rates (1 m/s)
or better; and Method C (0.01 % or better. Water content is an This standard provides guidelines for determining the fracture
important parameter for processing materials, and should remain toughness of plastics in the crack-opening mode (Mode I) by a linear
below the level specified in the approprite material standard. elastic fracture mechanics (LEMF) approach, at load-point
Price RM20 displacement rates up to 1 m/s.
Price RM30
MS ISO 15850 : 2004
Plastics – Determination of tension- Tension fatigue crack 83.080.10 Thermosetting materials
propagation – Linear elastic fracture mechanics (LEFM)
approach
This standard specifies a method for measuring the propagation of a MS 1336 : 1993
crack in a notched specimen subjected to a cyclic tensile load varying Method of test for plastics-compression moulding test
between a constant positive minimum and a constant positive specimens of thermosetting materials.
maximum value. The test results include the crack length as a function This standard specifies the general principles and the procedures to
of the load cycles and the crack length increase rate as a function of be followed for the preparation of test specimens from thermosetting
the stress intensity factor and energy release rate at the crack tip. compounds moulded under heat and pressure and for the
The possible occurrence of discontinuities in crack propagation is establishment of comparable test reports from different testing
detected and reported. organizations. It is applicable only to thermosetting materials based
Price RM30 upon phenolics, aminoplastics, melamine phenolics, expoxides and
unsaturated polyesters.
MS ISO 16014-1 : 2004 Price RM20
Plastics – Determination of average molecular mass and
molecular mass distribution of polymers using size-exclusion MS 1345 : 1993
chromatography – Part 1: General principles Method of test for plastics - Determination of tensile creep.
This standard specifies a general method for determining the average This standard specifies a method for the determination of tensile
molecular mass and the molecular mass distribution of polymers using creep of rigid plastic materials in the form of test specimens such as
size-exclusion chromatography (SEC). The average molecular mass those employed for the determination of tensile properties, moulded
and the molecular mass distribution are calculated from a calibration directly or cut from sheets.
curve constructed using polymer standards. Price RM20
Price RM30
MS 1349 : 1994
MS ISO 16014-2 : 2004 Method of test for plastics - Determination of flexural properties
Plastics – Determination of average molecular mass and of rigid plastics.
molecular mass distribution of polymers using size-exclusion This Malaysian Standard specifies a method for the determination of
chromatography – Part 2: Universal calibration method flexural properties of rigid non-reinforced and fibre-reinforced plastic
This standard specifies a method for determining the average materials, in the form of rectangular bars of standard on non-standard
molecular mass and the molecular mass distribution of polymers using dimensions, moulded directly or cut from sheets or other shapes. It
size-exclusion chromatography (SEC). applies only to a simple, freely supported beam, loaded at mid-span.
Price RM20
15
MS 1813 : 2005 MS 1334 : 1993
Standard test methods for ignition loss of cured reinforced Method of test for plastics-compression moulding test
resins specimens of thermoplastics materials.
This Malaysian Standard covers the determination of the ignition loss This standard specifies the general principles and the procedures to
of cured reinforced resins. The ignition loss can be considered to be be followed with thermoplastics in the preparation of compression-
the resin content within the limitation of 4.2. The values stated in SI moulded test specimens may be machined or stamped.
units are to regarded as the standard. Price RM20
Price RM40
MS 1343 : Part 1 : 1993
Method of test for plastics-amorphous thermoplastics -
83.080.20 Thermoplastic materials Preparation of test specimens with a specified maximum
reversion : Part 1 : Bars.
This Part of standard specifies procedures for the preparation of test
specimens of amorphous thermoplastic materials in the form of bars
MS 1012 : 2003 with a specified level of uniaxial molecular orientation which is
Specification for poly(vinyl chloride) (PVC) resins (First revision) characterized by determination of the maximum reversion. It is not
This Malaysian Standard specifies the requirements for poly(vinyl applicable to fibre reinforced thermoplastics or cellular plastics.
chloride) homopolymer resins produced by suspension Price RM10
polymerisation. These resins have a nominal specific gravity of 1.4
and theoretical chlorine content of 56.8 %. This Malaysian Standard MS 1343 : Part 2 : 1993
supersedes MS 1012:1986. Method of test for plastics-amorphous thermoplastics -
Price RM20 Preparation of test specimens with a specified maximum
reversion : Part 2 : Plates.
MS 1013 : 1986 This Part of standard specifies procedures for the preparation of test
Method of test for residual vinyl chloride monomer (Gas specimens with predominantly monoaxial orientation in the form of
Chromatographic Method). rectangular plates, made from rigid amorphous thermoplastic material.
Specifies a method for the determination of residual vinyl chloride Cellular plastic materials and fibre-containing plastic materials are
monomer by gas chromatography in homopolymer and copolymer excluded.
resins of vinyl chloride, as well as materials and articles made from Price RM20
resins.
Price RM10 MS 1371 : 1995
Methods of test for environmental stress – cracking of ethylene
MS 1267 : 1992 plastics.
Method of test for plastics : Determination of the Melt Flow Index This Malaysian Standard specifies methods for the determination of
of thermoplastics. the susceptibility of ethylene plastics to environmental stress –
The determination of the melt flow index MFI according to this cracking when subjected to certain condition. Under certain
standard is used for assessing the fluidity of thermoplastics under conditions of stress and in the presence of environments such as
specified conditions of pressure and temperature. The fluidity of high soaps, welting agents, oils or detergent, ethylene plastics may exibit
polymers is dependent on the rate of shear. mechanical failure by cracking.
MS 1269 : 1992 MS ISO 294-1 : 2002

Method of test for plastics : Determination of vicat softening Plastics - Injection moulding of test specimens of thermoplastics
temperature of thermoplastics. materials - Part 1 : General principles, and moulding of
This Malaysian Standard specifies two methods for the determination multipurpose and bar test specimens
of the Vicat softening temperature of thermoplastic materials: This Malaysian Standard specifies the general principles to be
Price RM10 followed when injection moulding test specimens of thermoplastic
materials and gives details of mould designs for preparing two types
MS 1303 : Part 1 : 1993 of specimen for use in acquiring reference data, i.e. multipurpose
Specification for thermoplastics road marking materials : Part 1 test specimens as specified in ISO 3167 and 80 mm x 10 mm x 10
: Requirements. mm x 4 mm bars. It provides a basis for establishing reproducible
This Malaysian Standard specifies requirements for white and yellow moulding conditions.
reflectorized thermoplastic road marking materials that are applied Price RM30
to the road surface in a molten state by mechanical means.
Price RM30 MS ISO 294-2 : 2002
Plastics - Injection moulding of test specimens of thermoplastics
materials - Part 2 : Small tensile bars
This Malaysian Standard specifies a four-cavity mould, the type C
ISO mould, for the injection moulding of small tensile bars measuring
> 60 mm x 10 mm x 3 mm (the type 4 test specimen in ISO 8256 :
1990).
Price RM10
MS ISO 294-3 : 2002

Plastics - Injection moulding of test specimens of thermoplastics
materials - Part 3 : Small plates
This Malaysian Standard specifies two two-cavity moulds, the type
D1 and D2 ISO moulds, for the injection moulding of small plates
measuring 60 mm x 60 mm with a preferred thickness of 1 mm (type
D1) or 2 mm (type D2) which can be used for a variety of tests (see
Annex A). The moulds may additionally be fitted with inserts for
16
studying the effects of weld lines on the mechanical properties (see volatile aromatic hydrocarbon in polystyrene. It is applicable both to
Annex B). styrene homopolymers and to butadiene modified polystyrene.
MS ISO 294-5 : 2004 MS ISO 2580 : Part 1 : 1994

Plastics – Injection moulding of test specimens of thermoplastic Plastics - Acrylonitrile/Butadiene/Styrene (ABS) moulding and
materials – Part 5: Preparation of standard specimens for extrusion materials : Part 1 : Designation
investigating anisotropy This Malaysian Standard establishes a system of designation for
This standard specifies a two-cavity mould (designated the type F arcylonitrile/butadiene/styrene (ABS) thermoplastic materials, which
ISO mould) for the injection moulding of 80 mm x 90 mm plates with may be used as the basis for specification.
a preferred thickness of 3 mm. Suitable test specimens [MS ISO Price RM10
527-2 type 1BA tensile test specimens or type 1 (80 mm x 10 mm)
bars] are then machined or die-cut from the plates and used to obtain MS ISO 2580-2 : 1999
information on the anisotropy of the thermoplastic parts. Plastics – Acrylonitrile/butadiene/styrene (ABS) moulding and
Price RM20 extrusion materials - Part 2 : Preparation of test specimens and
determination of properties
MS ISO 527 : Part 1 : 1994 Specifies the methods of preparation of test specimens and the test
Plastics - Determination of tensile properties : Part 1 : General methods to be used in determining the properties of ABS moulding
principles. and extrusion materials. Requirements for handling test material and
This Malaysian Standard specifies the test general principles for for conditioning both the test material before moulding and the
determining the tensile properties of plastics and plastic composites specimens before testing are given here. This standard is identical
under defined conditions. Several different types of test specimen with ISO 2580-2 : 1994.
are defined to suit different types of material which are detailed in Price RM20
subsequent parts of this Malaysian Standard.
Price RM20 MS ISO 2897-1 : 2001
Plastics - Impact-resistant polystyrene (PS-l) moulding and
MS ISO 527 : Part 2 : 1994 extrusion materials - Part 1 : Designation system and basis for
Plastics - Determination of tensile properties : Part 2 : Test specifications.
conditions for moulding and extrusion plastics. This part of MS ISO 2897 establishes a system of designation for
This Malaysian Standard specifies the test conditions for determining impact-resistant polystyrene (PS-l) thermoplastic materials, which
the tensile properties of moulding and extrusion plastics, based upon maybe used as the basis for specifications.
the general principles. Price RM10
Price RM10
MS ISO 2897-2 : 1999
MS ISO 1158 : 2002 Plastics – Impact-resistant polystyrene (PS-I) moulding and
Plastics – Vinyl chloride homopolymers and copolymers – extrusion materials - Part 2 : Preparation of test specimens and
Determination of chlorine content determination of properties
WARNING – All precautions shall be taken, particularly those Specifies the methods of preparation of test specimens and the test
mentioned in the text of the present Malaysian Standard, to methods to be used in determining the properties of PS-I moulding
protect operators from risk presented by both methods. and extrusion materials. Requirements for handling test material and
This Malaysian Standard specifies two methods for the determination for conditioning both the test material before moulding and the
of the chlorine content of homopolymers and copolymers of vinyl specimens before testing are given here. This standard is identical
chloride, free from plasticizers or additives, namely: with ISO 2897-2 : 1994.
- method A (combustion in a bomb); and Price RM20
- method B (combustion in a flask).
Price RM20 MS ISO 2898-1 : 2001
Plastics - Plasticized poly (vinyl chloride) (PVC-P) moulding and
MS ISO 1873 : Part 1 : 1994 extrusion materials - Part 1 : Designation system and basis for
Plastics - Polypropylene (PP) and propylene-copolymer specifications
thermoplastics : Part 1 : Designation. This part of MS ISO 2898 establishes a system of designation for
This Malaysian Standard establishes a system of designation for plasticized thermoplastic material which may be used as the basis
propylene (PP) thermoplastic materials, which may be used as the for specifications.
basis for specifications. Price RM10
Price RM10
MS ISO 2898-2 : 1999
MS ISO 1873 : Part 2 : 1994 Plastics – Plasticized poly(vinyl chloride) (PVC-P) moulding and
Plastics - Polypropylene (PP) and propylene-copolymers extrusion materials - Part 2 : Preparation of test specimens and
thermoplastics : Part 2 : Preparation of test specimens and determination of properties
determination of properties. Specifies the methods of preparation of test specimens and the test
This Malaysian Standard specifies procedures for moulding test methods to be used in determining the properties of PVC-P moulding
specimens of polypropylene materials under specified moulding and extrusion materials. Requirements for handling test material and
conditions and methods for measuring their properties. for conditioning both the test material before moulding and the
Price RM10 specimens before testing are given here.
Price RM20
MS ISO 2561 : 1998
Plastic –Determination of residual styrene monomer in MS ISO 4589-2 : 2000
polystyrene by gas chomatography. Plastics – Determination of burning behaviour by oxygen index
This Malaysian Standard specifies a method for the determination of – Part 2 : Ambient-temperature test
the residual styrene monomer in polystyrene by gas chromatography; Specifies methods for determining the minimum concentration of
it may be used also the simultaneous determination of other oxygen, in admixture with nitrogen, that will support combustion of
small vertical test specimens under specified test
17
conditions. The results are defined as oxygen index values. This test pieces prepared in the laboratory under standard conditions,
standard is identical with ISO 4589-2 : 1996. such as may be used to provide data for the development of rubber
Price RM30 compounds and control of methods of manufacture.
Price RM10
MS ISO 4610 : 2004
Plastics – Vinyl chloride homopolymer and copolymer resins – MS 1332 : 1993
Sieve analysis using air-jet sieve apparatus Methods of test for flexible cellular materials-slabs-bonded and
This standard specifies a method for the determination of the retention molded urethane foams.
and particle size distribution of preferably free-flowing vinyl chloride These methods apply to slab, bonded, and molded flexible cellular
homopolymer and copolymer resins prepared by the “suspension”, products known as urethane foams which may be generally defined
“bulk” and “emulsion” polymerisation processes. Control of these as an expanded cellular product produced by the interaction of active
characteristics can help to ensure consistency of supply and hydrogen compounds.
predictable processing behaviour. This standard may involve hazardous materials, operations, and
Price RM20 equipment.
Price RM50
MS ISO 4613-2 : 1999
Plastics – Ethylene/vinyl acetate (e/vac) moulding and extrusion MS 1528 : Part 1 : 2001
materials - Part 2 : Preparation of test specimens and Methods of test for rigid cellular plastics materials : Part 1 :
determination of properties Methods 1 to 5
Specifies the methods of preparation of test specimens and the test This Malaysian Standard describes five methods of test applicable
methods to be used in determining the properties of E/VAC moulding to rigid cellular products for determining:
and extrusion materials. Requirements for handling test material and a) the dimensions; b) the apparent density; c) the compression;
for conditioning both the test material before moulding and the d) the cross-breaking strength; and e) the dimensional stability of
specimens before testing are given here. This standard is identical cellular plastics such as polystyrene and polyurethane.
with ISO 4613-2 : 1995. Price RM30
Price RM10
MS 1809 : 2005
MS ISO 7391-1 : 2001 Test methods for flexible cellular materials – Slab, bonded and
Plastics - Polycarbonate (PC) moulding and extrusion materials moulded urethane foams
- Part 1 : Designation system and basis for specifications. These Malaysian Standard apply to slab, bonded and molded flexible
This part of MS ISO 7391 establishes a system of designation for cellular products known as urethane foams. Urethane foam may be
polycarbonate thermoplastic material, which may be used as the basis generally defined as an expanded cellular product produced by the
for specifications. interaction of active hydrogen compounds, water and isocynates.
MS ISO 7391-2 : 1999 MS 1871 : 2005

Plastics – Polycarbonate (PC) moulding and extrusion materials Flexible cellular polymeric materials – Determination of
- Part 2 : Preparation of test specimens and determination of compression set
properties This Malaysian Standard applies three methods for determining the
Specifies the methods of preparation of test specimens and the test compression set of flexible cellular materials. At present , this standard
methods to be used in determining the properties of polycarbonate applies only to latex and polyurethane foams of thickness greater
moulding and extrusion materials. Requirements for handling test than 2 mm. Methods for other materials will be added as required.
material and for conditioning both the test material before moulding Price RM20
and the specimens before testing are given here. This standard is
identical with ISO 7391-2 : 1996. MS 1872 : 2005
Price RM20 Flexible cellular polymeric materials – Determination of
compression set under humid conditions
MS ISO 8985 : 2000 This Malaysian Standard specifies a method for determining the
Plastics – Ethylene/vinyl acetate copolymer (EVAC) compression set of flexible cellular materials under humid conditions.
thermoplastics – Determination of vinyl acetate content This method consists of maintaining the test pieces under specified
Specifies two categories of method for the determination of the vinyl conditions of time, temperature, humidity and constant compressive
acetate (VAC) content of ethylene/vinyl acetate (EVAC) copolymers, strain and determining the effect on the thickness of the test piece
for use in the designation of such copolymers in accordance with after a specified recovery period.
ISO 4613-1 : 1997. One category is referred to as ‘reference methods’, Price RM10
the other as ‘test methods’. This standard is identical with ISO 8985
: 1998.
Price RM30
83.100 Cellular materials
MS 1157 : Part 38 : 2005

Methods of test for vulcanized rubber : Part 38 : Determination
of adhesion to metal – Two-plate method
This Malaysian Standard specifies a method for determining the
adhesion strength of rubber-to-metal bonds where the rubber part is
assembled between two parallel metal plates, using the adhesion
system under investigation. The method is applicable primarily to
18
MS ISO 1209-2 : 1997
Cellular plastics, rigid - Flexural tests - Part 2 : Determination of 83.140 Rubber and plastics products
flexural properties.
This standard specifies a method of test for determining the flexural
strength and the apparent flexural modulus of the elasticity of rigid MS 672 : 1999
cellular plastics. Specification of rubber seals in water supply, drainage and
Price RM10 sewerage pipelines (first revision)
Specifies requirements for rubber seals to be used in pipeline systems
MS ISO 1926 : 1997 which convey aqueous liquids at temperatures of less than 50°C.
Cellular Plastics - Determination of tensile properties of rigid The standard also specifies requirement for seals which incorporate
materials. root growth inhibitor and which are only intended for the conveyance
This standard specifies a method of determining the behaviour of of sewage or storm water. The standard does not specify the physical
rigid cellular plastics materials when they are subjected to a tensile dimensions or hardness requirements. This standard supersedes MS
stress. This standard applies primary to cellular materials having a 672 : 1980.
compression resistance sufficient to permit suitable gripping of the Price RM40
test pieces. In case it is impossible to grip the test piece, modify the
method in accordance with the variation described in Clause 8. MS 679 : 1999
Price RM10 Specification for latex foam rubber mattresses for domestic and
general use (First revision)
Prescribes the requirements and methods of test for mattresses made
of a latex foam rubber interior covered in a suitable ticking or proofed
83.120 Reinforced Plastic sheet and intended for domestic and general use. This Malaysian
Standard does not include mattresses with interiors made from
shredded latex foam rubber. This standard supersedes MS 679 :
MS 1337 : 1993 1980.
Method of test for plastics-preparation of glass fibre reinforced, Price RM20
resin bonded, low-pressure laminated plates or panels for test
purposes. MS 773 : 1999
This standard specifies the procedure for the preparation of test plates Specification for flexible rubber tubing and hose for use in LPG
or panels by bonding glass cloth or mats with low-pressure vapour phase and LPG/air installations (First revision)
thermosetting resins. In this standard the term ’low-pressure Specifies performance and dimensional requirements for rubber
thermosetting resins’ relates to resins which cure at or above room tubing, hose and complete assemblies for use in LPG vapour phase
temperature either without loss of reaction products or which are not and LPG/air installations in environments up to a maximum ambient
significantly altered by loss of reaction products during cure and which temperature of 60°C. NOTE 1. Tubing and hoses specified in this
can be processed with a pressure up to 3.5 MPa. standard should not be used for gas cutting and allied processes
Price RM20 using oxygen.
NOTE 2. The abbreviation “LPG” (liquefied petroleum gas) as used
MS 1418 : 1997 in this standard refers to butane and propane. This standard
Specification for glass fibre - reinforced plastics underground supersedes MS 773 : 1982.
storage tanks for petroleum products, alcohols and alcohols- Price RM30
gasoline mixtures.
These requirements cover spherical or horizontal cylindrical, MS 976 : 2004
atmospheric-type tanks of glass-fibre-reinforced plastics that are WC seats (plastics) – Specification (First revision)
intended for the underground storage of the petroleum-based Specifies materials, design, workmanship, dimensions and
flammable and combustible liquids, alcohols and combustible liquids, performance test requirements including impact resistance and rigidity
alcohols, alcohols-blended fuels. of the seat and cover. Interchangeability and installation including
Price RM20 reference to seat fastening bolts are considered.
Price RM20
MS 1811 : 2005
Test method for short-beam strength of polymer matrix MS 1151 : Part 1 : 2005
composite materials and their laminates. Plastics – Film and sheeting – Determination of tear resistance
This Malaysian Standard determines the short-beam strength of high- – Part 1 : Trouser tear method (First revision)
modules fiber-reinforced composites materials. The specimen is a This Malaysian Standard specifies a method of determining the tear
short beam machined from a curved or a flat laminate up to 6,00 mm resistance of plastic film or sheet less than 1 mm thick, in the form of
[0.25 in.] thick. The beam is loaded in three-point bending. standard trouser-shaped test specimens, tested under defined
Price RM50 conditions of pre-treatment, temperature, humidity and speed of
testing.
MS 1812 : 2005 Price RM10
Test methods for constituent content of composite materials
This Malaysian Standard determine the constituent content of MS 1504 : 2000
composite materials by one of two approaches. Method 1 physically Method of test for determination of thickness for flexible plastics
removes the matrix by digestion or ignition by one of seven laminates
procedures, leaving the reinforcement essentially unaffected and thus Specifies a method for the determination of thickness of flexible
allowing calculation of reinforcement or matrix content (by weight or plastics laminates by mechanical scanning method. This method is
volume) as well as percent void volume. Method II applicable only to not suitable for use with embossed flexible plastics laminates.
laminate materials of known fiber areal weight, calculates Price RM10
reinforcement or matrix content (by weight or volume) based on the
measured thickness of the laminate. Method II is not applicable to MS 1856 : 2005
the measurement of void volume. Test method for environmental stress crack resistance (ESCR)
Price RM50 of plastics tighthead drums not exceeding 60 gal (227 l) in rated
capacity
19
This Malaysian Standard provides an indication of the environmental MS 868 : 1999
stress crack resistance of plastic tighthead drums as a summation of Specification for natural rubber inner tubes for motorised
the effects of container design, resin, manufacturing conditions, field vehicles (first revision)
performance and other factors. Applies to inner tubes (natural rubber) for pneumatic tyres used on
Price RM40 scooters, motorcycles, passenger cars, light trucks, trucks, buses
and trailers. This standard supersedes MS 868 : 1986.
MS 1857 : 2005 Price RM20
Test method for environmental stress crack resistance (ESCR)
of threaded plastics closures MS 974 : 2002
This Malaysian Standard determines the susceptibility of threaded Specification for rubber swimming fins (First revision)
plastic closures to failure due to environmental stress cracking (ESC) This Malaysian Standard is applicable to rubber swimming fins used
Price RM40 on surface and underwater swimming for leisure purposes by free
divers, body surfers and swimmers. This standard supersedes MS
MS 1858 : 2005 974 : 1985.
Rigid plastics containers – Method for determination of Price RM10
drainability
This standard specifies a method for determination on the drainability MS 978 : 1985
of plastic bottles and jars with a nominal capacity up to 5 l and of Specification for plastics waste pipe and fittings.
plastics canisters/jerricans with a nominal volume up to 20 l. Covers plastic materials as stated:
Price RM10 (a) acrylonitrile-butadiene-styrene (ABS)
(b) modified unplasticised polyvinyl chloride (MUPVC) (c)
MS ISO 10508 : 2004 polypropylene (PP) (d) polyethylene (PE) intended to convey normal
Thermoplastics pipes and fittings for hot an cold water systems domestic effluent.
This standard specifies the performance requirements for hot and Price RM40
cold water pressure systems which use plastics pipes and plastics
or metal fittings. MS 979 : Part 1 : 1985
Price RM30 Specification for unplasticizes sewerage pipes and fittings : Part
1 : Pipes of diameter 100 millimeter and 155 millimeter.
MS ISO 11424 : 2002 Specifies material, colour, dimensions and testing of products for the
Rubber hoses and tubing for air and vacuum systems for conveyance of normal domestic effluents and surface water. Applies
internal-combustion engines - Specification to product laid under gardens, fields, driveway, yards and roads other
This Malaysian Standard specifies requirements for vulcanized-rubber than main roads.
hoses and tubing for use in the various air and vacuum systems Price RM40
found on internal-combustion engines.
Price RM20 MS 979 : Part 2 : 1985
Specification for unplasticized PVC underground sewerage
MS ISO 11425 : 2004 pipes and fittings : Part 2 : Pipes of diameter 200 millimetres
Rubber hoses and hose assemblies for automotive power- and above.
steering systems – Specification As in Part 1 of this standard but for diameters ranging from 200mm
Price RM20 to 630mm.
Price RM30
83.140.01 Rubber and plastics products in MS 1082 : 1994

Specification for elastomeric teats for feeding bottles (First
general
revision).
This Malaysian Standard specifies requirements for materials, design,
performance, packaging and marking for elastomeric teats for babies
MS 671 : Part 2 : 1992
feeding bottles which are not cleft lip or cleft of this Malaysian Standard
Specification for bridge bearing : Part 2 : Code of practice for
specifies requirements for materials, design, performance, packaging
design and installation of elastomeric bridge bearing.
palate teats. This standard includes test methods and
This Part of the Malaysian Standard gives recommendations for the
recommendations for use and care feed teats. This standard shall
design, performance and installation of elastomeric bridge bearings.
supersede MS 1082,’Specification for rubber teats for feeding bottles’.
It should be read in conjunction with MS 671 : Part 1 : The
Price RM20
recommendations given in this part are appropriate only when the
materials and workmanship comply with Part 1.
MS 1106 : 1988
Price RM20
Specification for heavy duty polyethylene sacks.
Specifies requirements for the properties of low density film used in
MS 773 : 1999
the manufacture of heavy duty low density polyethylene sacks of the
Specification for flexible rubber tubing and for use in LPG
pillow type, i.e. open top sacks.
vapour phase and LPG/air installations (First revision).
Price RM20
Specifies performance and dimensional requirements for rubber
tubing, hose and complete assemblies for use in LPG vapour phase
MS 1156 : 1989
and LPG/air installations in environments up to a maximum ambient
Specification for babies pacifiers.
temperature of 60°C.
Specifies requirements for materials, construction, design,
NOTE 1. Tubing and hoses specified in this standard should not be
performance, packaging and marking for babies pacifiers. The
used for gas cutting and allied processes using oxygen.
pacifiers, made of rubber and/or plastics materials may be constructed
NOTE 2. The abbreviation “LPG” (liquefied petroleum gas) as used
as a one-piece construction, or as an assembly of separate
in this standard refers to butane and propane. This standard
component parts.
Price RM20
Price RM30
20
MS 1268 : 1992 mass) of plastic film. Also described in this method in the means for
Specification for high-resilience polyurethane foam. calculating nominal yield, given values for nominal density and
This specification covers the minimum physical properties and other nominal thickness. This is need since, in material specification, limits
requirements for flexible high-resilience polyurethane foam. for yield are normally stated in terms of percent deviation of actual
- Method A using a load of 10 N yield for nominal yield.
- Method B using a load of 50 N Price RM10
The methods specified are applicable only to thermoplastics, for which
they give a measure of the temperature at which the thermoplastics MS 1556 : 2002
start to soften rapidly. Specification for plastics tableware
Price RM10 This Malaysian Standard specifies the requirements for plastics
tableware comprising plastics plates, cups, bowls and cutlery. It
MS 1312 : 1993 includes decorated tableware.
Methods of test for determination of volatile nitrosamines in Price RM20
rubber teats for feeding bottles and babies pacifiers -
Dichloromethane extraction method. MS 1557 : 2002
This Malaysian Standard describes a method suitable for the above Specification for plastics lockable containers for household
determination. The dichloromethane extraction method given herein wares
is a development of a technique referred to in legislation in the United This Malaysian Standard specifies the requirements for plastics
States. lockable containers for household wares of round and square shape
Price RM10 formed by injection moulding.
Price RM20
MS 1339 : 1993
Method of test for plastics - Film and sheeting-determination of MS 1558 : 2002
thickness by mechanical scanning. Specification for plastics food containers with lids
This standard specifies a method for the determination of thickness This Malaysian Standard specifies the requirements for plastics food
of a sample of plastic film or sheeting by mechanical scanning. This containers with lids with the capacity of 3.0 L or less. The containers
method is not suitable for use with embossed film and sheeting. may have lids with lock, screw or interlock.
MS 1344 : 1993 MS 1560 : 2002

Method of test for plastics - Determination of the gas Specification for measuring cups, spoons and litre measure for
transmission rate of films and thin sheets under atmospheric domestic purposes
pressure - Manometric method. This Malaysian Standard specifies the requirements for metric cup
This standard specifies a method for the determination of the gas measures, measuring spoons, fractional cup measures and litre
transmission rate of plastic films and thin sheets. The limits of the measures.
values which can be measured are from 1 to 20000 cm3/m2. The Price RM20
method can be used for measurements made either with air or with
other test gases. MS 1582 : 2003
Price RM20 Method of test for environmental stress-crack resistance of blow-
moulded polyethylene containers
MS 1385 : 1996 This Malaysian Standard measures the environmental stress-crack
Marine fenders - Specification for rubber materials. resistance of containers, which is the summation of the influence of
This Malaysian Standard specifies requirements for vulcanized rubber container design, resin, blow-moulding conditions, post treatment,
used in marine fenders for ports. General requirements for rubber or other factors that can affect this property. Three procedures are
materials stipulated include the hardness properties, tensile strength provided as follows: a) Procedure A, Stress-crack resistance of
and elongation at break, accelerated ageing, compression set, water containers commercial liquids. This procedure is particularly useful
absorption, ozone resistance, tear strength and abrasion resistance. for determining the effect of container design on stress-crack
Other requirements in particular the functional tests shall be the resistance of a proposed commercial package containing a proprietary
subject of agreement between interested parties. liquid product. b) Procedure B, Stress-crack resistance of a specific
Price RM20 container to polyoxyethylated nonylphenol, a stress-cracking agent.
This procedure is particularly useful for determining the effect of resin
MS 1400 : 1996 on the stress-crack resistance of the container. c) Procedure C,
Method of test for rubber threads. Controlled elevated pressure stress-crack resistance of a specific
This Malaysian Standard specifies methods of test for determining container to polyoxyethylated nonylphenol, a stress-cracking agent.
certain physical and mechanical properties of rubber threads. Price RM20
Price RM20
MS 1593 : 2003
MS 1405 : 1996 Method of test for environmental stress crack resistance of
Coding system for plastics products plastic injection moulded open head pails
This Malaysian Standard specifies standard coding system for plastics This test method provides procedures for an indication of the
products. The purpose of this standard is to provide a system for environmental stress crack resistance of plastic injection moulded
uniform marking of products which have been fabricated (excluding open head pails, covers, and components as a summation of the
additives, silk screening, metal-blading) from polymeric materials. effects of container design. resin, manufacturing conditions, field
This marking system is to provide assistance in identification of performance, and other factors. These procedures are not designed
plastics products for marking subsequent decisions as to handling, to test the ability of the cover gasketing material or closure to retain
disposal or recycling. the test reagent. Loss or leakage of the reagent through these
Price RM10 openings does not constitute container failure. However. this may
indicate an internal pressure loss that might affect test results.
MS 1424 : 1997 Price RM20
Method of test for package yield of plastic film.
This test method covers the determination of yield (area per unit
21
MS 1594 : 2003
Method of test for column crush properties of blown 83.140.10 Films and sheets
thermoplastic containers.
This Malaysian Standard specifies a method for the determination of _____________________________________________
mechanical properties of blown thermoplastic containers when loaded
under columnar crush conditions at a constant rate of compressive
deflection. Any container. whether blown commercially or in the MS 602 : 1979
laboratory, may be used as the test specimen. Specification for flexible, unsupported thick PVC sheeting.
Price RM20 For 6 types of sheeting ranging from 0.25mm to 1mm. Covers
definitions, stiffness, colour fastness, colour bleeding, adhesion of
MS 1733 : 2004 print, ply adhesion, retention of embossed surfaces, blocking, strength
Plastics - Guidelines on packaging in plastics containers and dimension requirements. Test methods appended.
This Malaysian Standard provides guidelines on packaging in Price RM30
containers made of plastics materials.
Price RM20 MS 681 : 1980
Specification for PVC film.
MS 1734 : 2004 Provides four standard types of film : Type 1, Type 2, Type 1F and
Plastics - Film and sheeting - Determination of oxygen gas Type 2F. Gives requirements for visual examination, pinholes,
transmission rate using a coulometric sensor thickness, colour bleeding, adhesion of print, ply adhesion, retention
This Malaysian Standard prescribes method for determination of the of embossed surface, blocking, ageing, colour fastness and
steady-state rate of transmission of oxygen gas through plastics in flammability. Sampling and test methods appended.
the form of film, sheeting, laminates, coextrusions, or plastics-coated Price RM30
papers or fabrics. The method is used to determine:
a) oxygen gas transmission rate (O2GTR); MS 1105 : 1988
b) the permeance of the film to oxygen gas (PO2); and Method of test for impact resistance of polyethylene film by the
c) oxygen permeability coefficient (PO 2 ); in the case of free-falling dart method.
homogenous materials. Covers the determination of the energy that causes polyethylene
Price RM20 film to fail under specified conditions of impact of a free falling dart.
This energy is expressed in terms of the weight (Mass) of the missile
MS 1735 : 2004 falling from a specified height which would result in 50% failure of
Plastics - Blow-moulded thermoplastic containers - specimen tested.
Determination of drop impact resistance Price RM20
This test method provides measures of the drop impact resistance
of blow-moulded thermoplastic containers as a summation of the MS 1150 : 1989
effects of material, manufacturing conditions, container design, and Method of test for determination of coefficients of friction of
perhaps other factors. plastics film.
Price RM20 Describes a procedure for determining the static and kinetic
coefficients of friction of a plastic film when sliding over itself at specific
MS 1769 : 2004 test conditions.
Portable cooler boxes – Specification Price RM10
This standard specifies the requirements for portable cooler boxes
whose main body is principally made of plastics, with the addition of MS 1151 : 1989
heat-insulating material, used for recreation such as outdoor activities, Method of test for tear resistance of plastics film and sheeting
etc. generally to keep contents of the portable cooler boxes cool. (Trouser tear method).
Price RM10 Specifies a method of test for tear resistance of plastics film on sheet
less than 1mm thick, in the form of standard trouser-shaped test
MS 1770 : 2004 specimens, tested under defined conditions of pretreatment,
Plastics films – Guidelines on the use for stretch wrapping temperature, humidity and speed of testing.
This Malaysian Standard provides general guidance on the use of Price RM10
plastics films for stretch wrapping of individual and unit loads
packages. MS 1151 : Part 2 : 1992
Price RM20 Method of test for tear resistance of plastics film and sheeting :
Part 2 : Elmendort method.
MS 1771 : 2004 This Malaysian Standard is the second part of the MOT for tear
Plastics films – Guidelines on the use for shrink wrapping resistance of plastics film and sheeting MS 1151. This Part of
This standard provides general guidance on the use of plastics films Malaysian Standard specifies a method of determining the force
for shrink wrapping of individual and unit load packages. required to propagate a tear through a specified distance and from a
Price RM20 specified slit, cut in a test specimen of thin flexible plastic sheeting or
film, under specified conditions of loading. Materials that can be tested
MS ISO 6427 : 1997 according to this method include flexible polyvinyl chloride (PVC)
Plastics - Determination of matter extractable by organic and polyolefin films.
solvents (Conventional method). Price RM20
This standard specifies method for the determination of components
in plastic that can be extracted by hot organics liquids near their
boiling points. The extractable components can be monomers,
polymers, plasticizers, stabilizers, etc. The kind and percentage of
extractable matter influence the properties of plastics.
Price RM20
22
MS 1420 : 1997 MS 1509 : 2000
Method of test for wetting tension of plastic film and sheeting. Method of test for film hardness of an organic coating by pencil
This Malaysian Standard specifies a method for determining the test
wetting tension of surfaces for plastics film and sheeting in contacts Specifies a procedure for rapid, inexpensive determination of the
with drops of specific test solution. film hardness of an organic coating on a substrate in terms of drawing
Price RM10 leads or pencil leads of known hardness.
Price RM10
MS 1422 : 1997
Method of test for unstrained linear thermal shrinkage of plastics MS 1559 : 2002
film and sheeting. Method of test for permeability of thermoplastic containers to
This test method covers the determination of the degree unstrainded packaged reagents or proprietary products
linear thermal shrinkage at given specimen temperature of plastic This test method covers procedures for determining the permeability
films and sheeting of 0.76 mm thickness or less. This test method of thermoplastic containers to packaged reagents or proprietary
does not cover shrinkage from loss of solvent in some materials. products under specified conditions of exposure. The exposures used
Price RM10 are intended to simulate the normal and elevated temperature–
storage condition that might be encountered in end–use application.
MS 1423 : 1997 Price RM20
Method of test for blocking of plastics film - Parallel plate method.
This test method yields quantitative information regarding the degree MS 1772 : Part 1 : 2004
of blocking (unwanted adhesion) existing between layers of plastics Flexible packaging material – Determination of residual solvents
film. It is not intended to measure susceptibility to blocking. by static headspace gas chromatography: Part 1: Absolute
Price RM20 methods
This standard describes methods for the quantitative determination
MS 1424 : 1997 of residual solvents in flexible packaging by static headspace
Method of test for package yield of plastic film. chromatography. The chemical identities of the residual solvents to
This test method covers the determination of yield (area per unit be determined by this method must be known before commencing
mass)of plastic film. Also described in this method in the means for the analysis. During the analysis there may be interferences from
calculating nominal yield, given values for nominal density and possible products of thermal decomposition. Residues from thermal
nominal thickness. This is need since, in material specification, limits decomposition products are not within the scope of this standard.
for yield are normally stated in terms of percent deviation of actual Additional peaks due to these products shall not be considered for
yield for nominal yield. evaluation of residual solvents. This method is applicable to flexible
Price RM10 packaging materials that may consist of mono- or multiplayer plastic
film, paper or board, foil or combination thereof. The method does
MS 1477 : 1999 not apply to residual solvents with amounts lower than 0.5 mg/m3.
Specification for polyethylene film and sheeting Price RM20
Specifies the classification of polyethylene film and sheeting up to
and including 300 mm (0.3 mm) in thickness. The film or sheeting MS 1772 : Part 2 : 2004
may contain additives for the improvement of the surface properties, Flexible packaging material – Determination of residual solvents
pigments or stabilisers. by static headspace gas chromatography: Part 2: Industrial
Price RM20 methods
This standard describes rapid methods as commonly used in quality
MS 1478 : 1999 control for example for monitoring the level of residual solvent used
Specification for low-density polyethylene films for general use in the production of flexible packaging by static headspace
and packaging applications chromatography. The procedure described involves one single
Specifies unpigmented, unsupported tubular, low-density injection of the headspace which implies an incomplete extraction of
polyethylene films (hereafter referred to as film or films) from resins the solvent. The values obtained may be lower than the absolute
having densities ranging from 910.0 kg/m3 to and including 925.0 kg/ content. During the analysis there may be interferences from possible
m3 (0.910 g/cm3 to and including 0.925 g/cm3), as measured on products of thermal decomposition. Residues from thermal
moulded plaques. decomposition products are not within the scope of this standard.
Price RM20 Additional peaks due to these products shall not be considered for
evaluation of residual solvents
MS 1479 : 1999 Price RM20
Specification for polyethylene sheeting for construction,
industrial and agricultural applications MS 1805 : 2005
Specifies polyethylene sheeting, 250 mm or less in thickness, Test method for resistance of plastics films to extraction by
intended for construction, industrial and agricultural applications. chemicals
Price RM20 This Malaysian Standard covers the measurement of the weight loss
of film after immersion in chemicals.
MS 1505 : 2005 Price RM40
Test method for comparison of bond strength or ply adhesion
of similar laminates made from flexible materials (First revision) MS 1806 : 2005
This Malaysian Standard covers a procedure for comparing the bond Test method for puncture-propagation tear resistance of plastics
strength or ply adhesion of similar laminates made from flexible film and thin sheeting
materials such as cellulose, paper, plastic film and foil. This includes This Malaysian Standard covers the determination of the dynamic
laminates made by various processes : adhesive laminates, extrusion tear resistance of plastic film and thin sheeting subjected to end-use
coatings, extrusion laminates and coextrusion. snagging-type hazards.
23
MS 1807 : 2005 fibre reinforced plastic composites, based upon the general principles
Test method for shrink tension and orientation release stress given in part 1. Unidirectionally reinforced materials are covered by
of plastics film and thin sheeting part 5.
This Malaysian Standard covers the determination of the shrink Price RM20
tension and related characteristics that is shrink force and orientation
release stress, of heat-shrinkable plastic film and sheeting of less MS ISO 527-5 : 2001
than 1,0 mm (0.04 in.) thickness. Two procedures are described that Plastics - Determination of tensile properties - Part 5 : Test
permit the measurement of shrink forces at predetermined conditions for unidirectional fibre-reinforced plastic composites
temperature. This part of MS ISO 527 specifies the test conditions for the
Price RM40 determination of the tensile properties of unidirectional fibre-reinforced
plastic composites, based upon the general principles given in part 1.
MS 1896 : 2005 Price RM20
Test method for evaluating load containment performance of
stretch wrap films by vibration testing MS ISO 2528 : 2000
This Malaysian Standard is used to evaluate and compare the ability Sheet materials - Determination of water vapour transmission
of stretch-wrap films to contain unitized loads during shipping. rate - Gravimetric (dish) method
Price RM40 Specifies a method for the determination of the water vapour
transmission rate (often erroneously called “permeability” of sheet
MS 1897 : 2005
materials. This method is not generally recommended for use if the
Test method for evaluating abrasion resistance of stretch wrap
transmission rate is expected to be less than 1 g/m2.d) or for materials
films by vibration testing
thicker than 3 mm.
This Malaysian Standard compares the abrasion resistance of similar
Price RM20
types of stretch wrap films.
Price RM40
MS ISO 8570 : 2004
MS 1898 : 2005 Plastics – Film and sheeting – Determination of cold-crack
Test method for protrusion puncture resistance of stretch wrap temperature
film This standard specifies a method for assessing the brittleness of
This Malaysian Standard determines the resistance of a stretch wrap plastic film and sheeting at low temperature. The assessment is given
film to the penetration of a probe at a standard low rate, a single test in the form of a conventional cold- crack temperature which serves
velocity. Performed at standard conditions, the test method imparts as a guidelines for comparing the low-temperature behaviour of
a biaxial stress that is representative of the type of a stress plastics film and sheeting.
encountered in many product end-use applications. Price RM20
Price RM40
MS 1899 : 2005
Test methods for hot seal strength (hot tack) of thermoplastic
polymers and blends comprising the sealing surfaces of flexible
webs
This Malaysian Standard cover laboratory measurement of the
strength of heatseals formed between thermoplastic surfaces of
flexible webs, immediately after a seal has been made and before it
cools to ambient temperature.
Price RM40
MS 2000 : 2005
Test method for water vapour transmission rate through plastics
film and sheeting using a modulated infrared sensor
This Malaysian Standard covers a procedure for determining the
rate of water vapor transmission through flexible barrier materials.
Price RM50
MS 2001 : 2005
Test method for peel cling of stretch wrap film
This Malaysian standard measures cling between two layers of film,
in both a stretched and unstretched conditions.
Price RM50
MS ISO 527-3 : 2001

Plastics - Determination of tensile properties - Part 3 : Test
conditions for films and sheets
This part of MS ISO 527 specifies the conditions for determining the
tensile properties of plastic films or sheets less than 1 mm thick,
based upon the general principles given in part 1. This standard
supersedes MS 1152 : 1989
Price RM10
MS ISO 527-4 : 2001

Plastics - Determination of tensile properties - Part 4 : Test
conditions for isotropic and orthotropic fibre-reinforced plastic
composites
This part of MS ISO 527 specifies the test conditions for the
determination of the tensile properties of isotropic and orthotropic
24
whether or not intended for human consumption, (domestic systems)
83.140.30 Plastics pipes, fittings and valves and for heating systems, under design pressures and temperatures
appropriate to the class of application.
Price RM20
MS 978 : 1985
Specification for plastics waste pipe and fittings. MS 1736 : Part 5 : 2004
Covers plastic materials as stated: Plastics piping systems for hot and cold water installations -
(a) acrylonitrile-butadiene-styrene (ABS) Crosslinked polyethylene (PE-X) : Part 5 : Fitness for purposes
(b) modified unplasticised polyvinyl chloride (MUPVC) of the system
(c) polypropylene (PP) This standard specifies the characteristics of the fitness for purpose
(d) polyethylene (PE) intended to convey normal domestic of crosslinked polyethylene (PE-X) piping systems, intended to be
effluent. used for hot and cold water installations within buildings for the
Price RM40 conveyance of water whether or not intended for human consumption
(domestic systems) and for heating systems, under design pressures
MS 979 : Part 1 : 1985 and temperatures according to the class of application.
Specification for unplasticized PVC underground sewerage Price RM20
pipes and fittings : Part 1 : Pipes of diameter 100 millimeter and
155 millimeter. MS 1736 : Part 7 : 2004
Specifies material, colour, dimensions and testing of products for the Plastics piping systems for hot and cold water installations -
conveyance of normal domestic effluents and surface water. Applies Crosslinked polyethylene (PE-X): Part 7: Guidance for the
to product laid under gardens, fields, driveway, yards and roads other assessment of conformity
than main roads. This Technical Specification gives guidance for the assessment of
Price RM40 conformity to be included in the manufacturer’s quality plan as part
of his quality system.
MS 979 : Part 2 : 1985 Price RM50
Specification for unplasticized PVC underground sewerage
pipes and fittings : Part 2 : Pipes of diameter 200 millimetres MS 1737 : 2004
and above. Plastics piping systems- Guidance for the installation inside
As in Part 1 of this standard but for diameters ranging from 200 mm buildings of pressure piping systems for hot and cold water
to 630 mm. intended for human consumption.
Price RM30 This standard recommends practices to be followed in the application
and installation of thermoplastics pipes and associated fittings.
MS 1010 : 1986 Price RM30
Specification for rigid polyvinyl chloride and related plastic pipe
and fittings compounds. MS 1738 : 2004
This Malaysian Standard specifies the physical requirements and Plastics piping systems - Injection-moulded thermoplastics
test methods for the rigid vinyl chloride compounds for pipes and fittings, valves and ancillary equipment - Determination of the
fittings. The compounding ingredients may consist of lubricants, long-term hydrostatic strength of thermoplastics materials for
stabilizers, (vinyl chloride), resin modifiers, pigments and inorganic injection moulding of piping components.
fillers. This standard specifies method for preparing tubular test pieces for
Price RM30 testing thermoplastics materials used for injection moulding, to
evaluate the long term resistance to constant internal water pressure
MS 1736 : Part 1 : 2004 at constant temperature and to check the hydrostatic strength of the
Plastics piping systems for hot and cold water installations – material.
Crosslinked polyethylene (PE-X): Part 1: General Price RM10
This Malaysian Standard specifies the general aspects of crosslinked
polyethylene (PE-X) piping systems intended to be used for hot and MS 1739 : 2004
cold water installations within buildings for the conveyance of water, Plastics piping systems - Thermoplastics pipes and fittings for
whether or not intended for human consumption (domestic systems), hot and cold water - Test method for the resistance of mounted
and for heating systems, under design pressures and temperatures assemblies to temperature cycling
according to the class of application. This Malaysian Standard specifies a method for testing the resistance
Price RM20 to temperature cycling of joints for piping systems with rigid or flexible
thermoplastics pipes. It is applicable to thermoplastics piping systems
MS 1736 : Part 2 : 2004 intended to be used in hot and cold water pressure applications.
Plastics piping systems for hot and cold water Installations - Price RM10
Crosslinked polyethylene (PE-X) : Part 2 : Pipes
This Malaysian Standard specifies the Characteristics of pipes made
from crosslinked polyethylene (PE-X) for piping systems intended to
be used for hot and cold water installations within buildings for the
conveyance of water, whether or not intended for human consumption
(domestic systems), and for heating systems, under design pressures
and temperatures appropriate to the class of application.
Price RM20
MS 1736 : Part 3 : 2004

Plastics piping systems for hot and cold water installations -
Crosslinked polyehtylene (PE-X) : Part 3 : Fittings
This standard specifies the characteristics of fittings for crosslinked
polyethylene (PE-X) piping systems intended to be used for hot and
cold water installations within buildings for the conveyance of water
25
MS 1740 : 2004 MS ISO 15876-7 : 2004
Thermoplastics piping systems - End-load bearing mechanical Plastics piping systems for hot and cold water installation -
joints between pressure pipes and fittings - Test method for Polybutylene (PB)- Part 7: Guidance for the assessment of
resistance to pull out under constant longitudinal force conformity
This Malaysian Standard specifies a method for checking the ability This technical Specification gives guidance for the assessment of
of assembled end-load bearing mechanical joints (excluding fusion- conformity to be included in the manufacturer’s quality plan as part
welded joints) between fittings and pressure pipes to withstand a of his quality system.
longitudinal tensile force. Price RM30
Price RM10
MS 1741 : 2004
Plastics piping systems - Mechanical joints between fittings and 83.140.40 Hoses
polyolefin pressure pipes - Test method for leaktightness under
internal pressure of assemblies subjected to bending
This standard specifies a method for checking the leaktighness under MS 773 : 1999
internal hydrostatic pressure of assembled mechanical joints Specification for flexible rubber tubing and hose (including
(excluding fusion-welded joints) between fittings and polyolefins connections where fitted and safety recommendations) for use
pressure pipes while subjected to bending. in LPG vapour phase and LPG/air installations.
Price RM10 Covers performance and dimensional requirements and safe
operations for flexible tubing used in installations not exceeding 17.5
MS 1761 : 2004 bar. Excludes tubings for gas cutting and welding applications. Tests
Plastics pipes and fittings – Determination of the opacity include resistance to KinKing crushing ageing and burst to substances
This Malaysian Standard specifies a method for determining the such as ozone and pentane.
opacity of plastics pipes and fittings. Price RM30
Price RM10
MS 1070 : 2002
MS ISO 15876-1 : 2004 Specification for rubber radiator hoses for automotive internal
Plastics piping systems for hot and cold water installations- combustion engine (first revision)
Polybutylene (PB)- Part 1 : General This standard specifies the requirements of rubber hoses for use in
This Part of prEN ISO 15876 specifies the general aspects of the cooling system of automotive internal combustion engines.
polybutylene (PB) piping systems intended to used for hot and cold Note: The hoses shall be used in positions where they are not likely
water installations within buildings for the conveyance of water to be subjected to outside surface contamination by fuel and
whether or not intended for human consumption (domestic systems) lubricating oils. This standard supersedes MS 1070: 1987.
and for heating systems, under design pressures and temperatures Price RM20
according to the class of application .
Price RM20 MS 1545 : 2002
Rubber hoses for agricultural spraying
MS ISO 15876-2 : 2004 This Malaysian Standard specifies requirements for three types of
Plastics piping systems for hot and cold water installations - flexible rubber hose for pressure spraying of agropharmaceutical and/
Polybutylene (PB) - Part 2 : Pipes or fertilizer products within a temperature range of -10 °C to + 60 °C.
This Part prEN ISO 15876 specifies the characteristics of pipes made Price RM10
of polybutylene (PB) for piping systems intended to be used for hot
and cold water installations within buildings for the conveyance of MS ISO 1403 : 2002
water whether or not intended for human consumption (domestic Rubber hoses, textile-reinforced, for general-purpose water
systems), and for heating systems, under design pressure and applications - Specification
temperatures appropriate to the class of application. This Malaysian Standard specifies the requirements for three types
Price RM30 of general-purpose textile-reinforced rubber water hose with an
operating range of -25°C to + 70°C, and a maximum working pressure
MS ISO 15876-3 : 2004 of up to 2,5 MPa.
Plastics piping systems for hot and cold water installations - Price RM10
Polybutylene (PB) - Part 3 : Fittings
This Part of prEN ISO 15876 specifies the characteristics of fittings MS ISO 3821 : 2002
for polypropylene (PB) piping systems intended to be used for hot Gas welding equipment - Rubber hoses for welding, cutting and
and cold water installations within buildings for the conveyance of allied processes
water, whether or not intended for human consumption (domestic This Malaysian Standard specifies requirements for rubber hoses
systems) and for heating systems under design pressure and (including twin hoses) for welding, cutting and allied processes. The
temperature according to the class of application. term “allied processes” means, in particular, heating, brazing and
Price RM30 metallization.
Price RM20
MS ISO 15876-5 : 2004
Plastics piping systems for hot and cold water installations -
Polybutylene (PB)- Part 5 : Fitness for purpose of the system
This Part of prEN ISO 15876 specifies the characteristic of the fitness
for purpose of polybutylene (PB) piping systems, intended to be used
for hot and cold water installations within buildings for the conveyance
of water, whether or not intended for human consumption, (domestic
systems) and for heating systems, under design pressures and
temperatures according to the class of application.
Price RM20
26
MS ISO 4642 : 2004 MS 1068 : 2002
Rubber products – Hoses, non-collapsible, for fire-fighting Specification for rubber floor mats for vehicles (First revision)
service This Malaysian Standard applies to floor mats made of rubber
Price RM10 intended for use in motor vehicles and electric vehicles. This standard
Price RM10
83.140.50 Seals
MS 1155 : 2003
Single-use medical examination gloves – Specification
MS 672 : 1999 This Malaysian Standard specifies requirements for packaged sterile,
Specification of rubber seals in water supply, drainage and or bulked non-sterile, rubber gloves intended for use in medical
sewerage pipelines (first revision) examinations and diagnostic or therapeutic procedures to protect
Specifies requirements for rubber seals to be used in pipeline systems the patient and the user from cross-contamination. It also covers
which convey aqueous liquids at temperatures of less than 50°C. rubber gloves intended for use in handling contaminated medical
The standard also specifies requirement for seals which incorporate materials and gloves with smooth surfaces or with textured surfaces
root growth inhibitor and which are only intended for the conveyance over part or all of the glove. This standard is intended as a reference
of sewage or storm water. The standard does not specify the physical for the performance and safety of rubber examination gloves. The
dimensions or hardness requirements. This standard supersedes safe and proper usage of examination gloves and sterilisation
MS 672 : 1980. procedures with subsequent handling, packaging and storage
Price RM40 procedures are outside the scope of this standard.
Price RM20
MS 1225 : Part 1 : 2004

Plastics - Polyethylene (PE) tanks for cold water storage - Part
1 : Capacity up to 600 gal (First revision)
This Malaysian Standard specifies requirements for materials,
physical properties and performance of polyethylene tank up to 600
gal capacity, used for cold water storage.
Price RM30
83.140.99 Other rubber and plastics products MS 1225 : Part 2 : 2006

Polyethylene (PE) tanks for cold water storage – Part 2 : Capacity
more than 600 gal (First revision)
MS 676 : 2001 This Malaysian Standard specifies requirements for materials,
Specification for plastics buckets (First revision) physical properties and performance of polyethylene tank more than
This Malaysian Standard specifies the requirements for plastic 600 Imperial Gallons (2730 L) capacity, used for cold water storage.
buckets of all shapes (including lids, if any) formed by injection Price RM30
moulding process. This standard supersedes MS 676 : 1980.
Price RM10 MS 1291 : 2003
Single-use sterile rubber surgical gloves – Specification
MS 679 : 1999 This Malaysian Standard specifies requirements for packaged sterile
Specification for latex foam rubber mattresses for domestic and rubber gloves intended for use in surgical procedures to protect the
general use (First revision). patient and the user from cross-contamination. It is applicable to
Prescribes the requirements and methods of test for mattresses made single-use gloves that are worn once and the discarded. It does not
of a latex foam rubber interior covered in a suitable ticking or proofed apply to examination or procedure gloves. It covers gloves with
sheet and intended for domestic and general use. This Malaysian smooth surfaces and gloves with textured surfaces over part or all of
Standard does not include mattresses with interiors made from the glove. This standard is intended as a reference for the
shredded latex foam rubber. This standard supersedes MS 679 : performance and safety of rubber surgical gloves. The safe and proper
1980. usage of surgical gloves and sterilisation procedures with subsequent
NOTE: Developed by Malaysian Rubber Board (SWO). handling, packaging and storage procedures are outside the scope
Price RM20 of this Malaysian Standard.
Price RM20
MS 735 : 1996
Specification for plastics feeding bottles (First revision). MS 1407 : Part 1 : 1996
This Malaysian Standard is the first revision of MS 735 : 1981. This Specification for plastics containers: Part 1 : Screw thread
revision prescribes requirements and method of test for plastics finishes for plastics containers.
feeding bottles. Amongst the requirements specified in this standard This Malaysian Standard specifies plastics used as receptable of
are materials, design, performance, packaging and marking. The standards design for the transport of standards design for the transport
major amendments incorporated in this revision are the requirements of goods for packaging of liquids, powder and pellets.
for heavy metals in the plastics components parts of the feeding Price RM30
bottles and minimum scale marks for the bottles. This standard shall
supersede MS 735 : 1981. MS 1407 : Part 2 : 1996
Price RM20 Specification for plastics containers: Part 2 : Capacity, mass
and tolerances on dimensions for plastics containers having
MS 973 : 2002 capacity of less than 5 liters.
Specification for rubber bands (First revision) This part of the Malaysian Standard specifies tolerances on capacities,
This Malaysian Standard covers rubber bands for general purposes mass and dimensions for plastics containers having capacity of less
and does not cover sealing rings used for sealing purpose, or than 5 liters.
transmission belts, used for transmitting mechanical power Price RM30
continuously. This standard supersedes MS 973 : 1985.
Price RM10
27
MS 1407 : Part 3 : 2001 trunnion or BG – Lifting device and/or wide comb lifting devices
Specification for plastics containers : Part 3 : Container over 5 – Dimensions and design
L up to and including 60 L capacity This Malaysian Standard specifies dimensions and design
This part of this Malaysian Standard specifies tolerances on requirements of mobile waste containers with four wheels, with flat
dimensions and performance requirements for free standing blow lid(s) and capacity from 750 L to 1 700 L to be used by wide trunnion
moulded containers with capacities over 5 L up to and including 60L. or BG–lifting device and/or wide comb lifting device.
MS 1407 : Part 4 : 2001 MS 1564 : Part 5 : 2002

Specification for plastics containers : Part 4 : Drums over 70 L Specifications for mobile waste containers: Part 5: Performance
up to including 250 L capacity requirements and test methods
This part of this Malaysian Standard specifies the capacity, mass This Malaysian Standard prescribes the test methods and the
and tolerances on dimensions for blow moulded drums having requirements for mobile waste containers specified in MS 1564:
capacity over 70 L up to and including 250 L. Part 1 to MS 1564: Part 4. This standard is applicable to plastics
Price RM20 and metal mobile waste containers with capacities from 80 L to
1,700 L.
MS 1502 : 2000 Price RM20
Specification for disposable polystyrene cutlery
Specifies material and performance requirements for disposable MS 1564 : Part 6 : 2002
polystyrene cutlery which are intended for use in contact with food Specifications for mobile waste containers: Part 6: Safety and
and drinks up to a maximum service temperature of 100 °C. health requirements
Price RM30 This Malaysian Standard provides the most essential safety and
health requirements for plastics and metal mobile waste containers,
MS 1510 : 2000 not including hazardous wastes containers.
Specification for polystyrene cushioning foams Price RM10
Specifies expandable polystyrene foam used as package cushioning
material. It does not cover polystyrene foam in chip or granular form.
Price RM20 83.160 Tyres
MS 1521 : 2001
Specification for polyolefin woven open-mouth sacks
MS 150 : 1999
This Malaysian Standard specifies requirements for the materials,
Standard practice for determination of bead unseating
dimensions and performance of open-mouth sacks manufactured
resistance of a tubeless passenger car tyre (First revision)
from plain weave fabrics produced from polyolefin tape yarns.
Covers the determination of force required to completely dislodge
Price RM20
the bead of an inflated tubeless passenger car tyre from its rim as
indicated by a loss of inflation pressure or a sudden drop in bead
MS 1530 : 2001
unseating force as exerted by a bead unseating block.
Specification for plastics washing basins
Price RM10
This Malaysian Standard specifies the requirements for plastic
washing basins for domestic use.
MS 224 : 2005
Price RM10
Retreaded pneumatic rubber tyres for passenger cars and
commercial vehicles – Specification (Second revision)
MS 1564 : Part 1 : 2003
This Malaysian Standard specifies requirements for retreading of
Mobile waste containers: Part 1: Containers with two wheels
pneumatic highway tyres including passenger car tyres and tyres
with a capacity from 80 L to 1 390 L for comb lifting devices –
for multi-purpose passenger vehicles, trucks, buses, trailers and
Dimensions and design
other commercial vehicles used on the public road.
Price RM30
Price RM20
MS 1564 : Part 2 : 2003
Mobile waste containers: Part 2: Containers with four wheels
with a capacity 500 L to 1 200 L with flat lid(s), for trunnion and/
or comb lifting devices – Dimensions and design
Price RM30
MS 1564 : Part 3 : 2002

with a capacity from 770 L to 1 300 L with dome lid(s), for trunnion
and/or comb lifting devices – Dimensions and design
This Malaysian Standard specifies dimensions and design
requirements of mobile waste containers with four wheels, with dome
lid(s) and capacity from 770 L to 1 300 L to be used by trunnion and/
or comb lifting device.
Price RM30
MS 1564 : Part 4 : 2002

with a capacity from 750 L to 1 700 L with flat lid/(s), for wide
Best Seller
28
MS 868 : 1999 - Method A, using a trouser test piece; - Method B, using an angle
Specification for natural rubber inner tubes for motorised test piece, with or without a nick of specified depth; and- Method C,
vehicles (first revision) using a crescent test piece with a nick. This standard supersedes
Applies to inner tubes (natural rubber) for pneumatic tyres used on MS 1157: Part 6: 1994.
scooters, motorcycles, passenger cars, light trucks, trucks, buses Price RM20
and trailers. This standard supersedes MS 868 : 1986.
Rubber and lattices – Nomenclature
MS 1443 : 1998 Price RM10
Standard test apparatus for using a nominal 1707 mm diameter
laboratory test roadwheel in testing tyres. MS ISO 4570-1 : 2002
This practice describes the requirements for a 1707 mm diameter Tyre valve threads - Part l : Threads 5V1, 5V2, 6V1 and 8V1
laboratory roadwheel for durability testing of tyres under controlled This Malaysian Standard specifies limit dimensions and tolerances
operating environmental conditions. for tyre valve threads 5V1, 5V2, 6V1 and 8V1.
MS 1444 : 1998 MS ISO 4570-2 : 2002

Standard test method for energy absorbed by a tyre when Tyre valve threads - Part ll : Threads 9V1, 10V2, 12V1 and 13V1
deformed by a slow moving plunger. This Malaysian Standard specifies limit dimensions and tolerances
This standard covers the determination of tyre plunger energy for tyre valve threads 9V1, 10V2, 12V1 and 13V1.
required to completely penetrate the tread area of an inflated tyre as Price RM10
indicate by a rapture, loss of inflation pressure, sudden drop in plunger
force or bottom –out. The test requires utilisation of a laboratory testing MS ISO 4570-3 : 2002
machine equipped with a slow-moving plunger which has a Tyre valve threads - Part 3 : Threads 8V2, 10V1, 11V1, 13V2,
hemispherical end. 15V1, 16V1, 17V1, 17V2, 17V3, 19V1, 20V1
Price RM10 This Malaysian Standard specifies limit dimensions and tolerances
for tyre valve threads 8V2, 10V1, 11V1, 13V2, 15V1, 16V1, 17V1,
MS 1478 : 1999 17V2, 17V3, 19V1 and 20V1.
Specification for low-density polyethylene films for general use Price RM20
and packaging applications
Specifies unpigmented, unsupported tubular, low-density MS ISO 6762 : 2002
polyethylene films (hereafter referred to as film or films) from resins Tyre valves - ISO core chamber No. 2
having densities ranging from 910.0 kg/m3 to and including 925.0 kg/ This Malaysian Standard specifies the interchangeability dimensions
m3 (0.910 g/cm3 to and including 0.925 g/cm3), as measured on of an ISO core chamber No. 2 (large bore), and applies principally to
moulded plaques. This specification is applicable to homopolymer core chambers of valves used on tyres for agricultural machines,
polyethylene, but is not restricted to it. earth-moving machines and civil aircraft.
MS 1479 : 1999 MS ISO 9413 : 2002

Specification for polyethylene sheeting for construction, Tyre valves - Dimensions and designation
industrial and agricultural applications This Malaysian Standard defines the essential dimensions and the
Specifies polyethylene sheeting, 250 mm or less in thickness, designation of tube valves and tubeless valves.
intended for construction, industrial and agricultural applications. Price RM80
Price RM20
MS 1565 : 2002 83.160.10 Road vehicle tyres

Motorcycle tyre dimensions and rims (Inch code – Designated
series)
This Malaysian Standard sets out the designations in use and the
MS 148 : Part 1 : 1973
dimensions for inch code designated series of motorcycle tyres. This
Specification for tyre and wheel data : Part 1 : Pneumatic rubber
Malaysian Standard applies to motorcycle tyres used on highway
tyres.
and off the road service with a speed rating of not exceeding 240
Applies to pneumatic rubber tyres for passenger cars and gives
km/h and fitted on rims with normal diameters corresponding to the
recommended tyre size with loads and inflation pressure schedules.
codes 14, 15, 16, 17, 18, 19, 21 and 23 inches.
Requirements for marking and test procedures included.
Price RM20
Price RM30
MS 1566 : 2002
Definitions of common terms used in the tyres industry – Solid
tyres
This Malaysian Standard describes the definitions of common terms
relating to solid tyres, as used in the tyres industry. This Malaysian
Standard does not include pneumatic tyres which are within the scope
of “MS 1439: 1998 – Definitions of common terms used in the tyre
industry – Pneumatic tyres”.
Price RM10
MS 1567 : Part 1 : 2002

Rubber, vulcanised or thermoplastic – Determination of tear
strength – Part 1: Trouser, angle and crescent test pieces
This part of MS 1567 specifies three test methods for the
determination of the tear strength of vulcanised rubber, namely
29
MS 876 : 1984
Specification for pressure sensitive polyvinyl chloride adhesive
Best Sellers tapes for electrical insulation.
Covers tapes with specific electrical properties for holding, binding
MS 149 : 1992 for insulating purposes. Requirements include working temperature,
Specification for new pneumatic passenger car tyres (First appearance, colour, dimensions and range of physical and electrical
revision). properties
This Malaysian Standard specifies definitions, designations testing Price RM30
and minimum safety requirements for new pneumatic rubber tyres
for use on passenger cars. MS 908 : 1984
Price RM20 Specification for synthetic resin adhesives (Phenolic and
aminoplastic) for plywood.
MS 1097 : 2005 Describes technical requirements and test methods to determine
Rubber tread compound for hot (conventional) retreading of moisture content, pH value, mycological test and resistance to water
passenger car and commercial vehicle tyres – Specification for adhesives with or without hardeners. Applies to all the three forms
(First revision) of liquid, powder or film.
This Malaysian Standard specifies the minimum requirements for Price RM20
rubber tread compound for retreading of pneumatic tyres for use of
passenger cars and commercial vehicles. MS 1295 : 1992
Price RM10 Specification for adhesives for use with ceramic tiles and
mosaics.
MS 1208 : 2005 This Malaysian Standard specifies the minimum requirements for
Precured tread for retreading tyres – Specification (First adhesives used for fixing tiles to ensure that they are suitable for
revision) their proposed application. The adhesives specifies in this Malaysian
This Malaysian Standard specifies the minimum requirements for Standard are classified into five types by their chemical composition
procured tread for retreading tyres. and physical form and into three classes based on their resistance
Price RM10 to water.
Price RM30
MS 1348 : 2005
Cushion gum used in procured retreading of tyres – MS 1563 : 2002
Specification (First revision) Specification on adhesive for bonding decorative thermoset
This Malaysian Standard specifies the requirements for cushion gum laminates (contact adhesives)
used in procured process of retreading tyres. This Malaysian Standard applies to sprayable adhesives and
Price RM10 brushable adhesives (including those for application by scraper)
intended for the bonding, on the contact bond principle, of decorative
MS 1394 : 1996 thermoset laminated sheets to materials such as timber, metal, and
Specification for new pneumatic tyres for highway vehicles reconstituted boards.
other than passenger cars. Price RM30
This Malaysian Standard specifies requirements such as endurance,
strength, high speed performance and marking for pneumatic tyre MS 1810 : 2005
other than that of passenger car which is to use gazetted roads. It Test method for determining strength of adhesively bonded rigid
also includes tyre for motorcycle. plastic lap-shear joints in shear by tension loading
Price RM20 This Malaysian Standard is intended to complement Test Method D
1002 and extend its application to single-lap shear adhesive joints of
rigid plastic adherends. The test method is useful for generating
comparative shear strength data for joints made from a number of
plastics. It can also provide a means by which several plastic surface
MS 1439 : 1998 treatments can be compared.
Definition of common terms used in the tyre industry-Pneumatic Price RM40
tyres
This Malaysian Standard gives definition of common terms relating MS ISO 13007-1 : 2005
to pneumatic tyres as used in the tyre industry. Ceramic tiles - Grouts and adhesives – Part 1 : Terms, definitions
Price RM20 and specifications for adhesives
This standard is applicable to ceramic tile adhesives for internal and
MS ISO 4000-1 : 2002 external tile installations on walls and floors. This standard also
Passenger car tyres and rims - Part 1 : Tyres (metric series) establishes the terminology, concerning the products, working
This Malaysian Standard specifies the designation, dimensions and methods, application properties, etc. , for ceramic tile adhesives. It
load ratings of the metric series of tyres primarily intended for also specifies the values of performance requirements for all ceramic
passenger cars. tile adhesives [cementitious (C), dispersion (D) and reaction resin ®
Price RM30 adhesives ]
Price RM20
83.180 Adhesives
MS 562 : 1978 (2002)

Glossary of terms used in the adhesives industry.
Makes provisions for uniformity in the definitions of terms used in
the local adhesives industry and practice.
Price RM50
30
MS ISO 13007-2 : 2005
Ceramic tiles - Grouts and adhesives – Part 2 : Test methods
for adhesives
This standard specifies methods for determining characteristics for
adhesives used in the installation of ceramic tiles. The following test
methods are described :
- determination of open time (4.1), determination of slip (4.2),
determination of shear adhesion strength (4.3), determination of
tensile adhesion strength (4.4), determination of transverse
deformation (4.5), determination of chemical resistance (4.6)
Price RM50
MS ISO 15605 : 2003

Adhesives - Sampling
This Malaysian Standard specifies methods for sampling adhesives
and related products, in order to obtain uniform samples of convenient
size which are adequately representative of the product being
sampled.
Price RM20
83.200 Equipment for rubber and plastics

industries
_____________________________________________
MS ISO 13802 : 2004

Plastics – Verification of pendulum impact-testing machines –
Charpy, izod and tensile impact-testing
This standard specifies methods for the verification of pendulum
impact-testing machines used for the Charphy impact test, Izod impact
test and tensile test described in MS ISO 179-1, MS ISO 180 and
MS ISO 8256, respectively. The test machines covered by this
standard are of the pendulum type. The impact energy absorbed in
impating a test specimen is taken as being equal to the difference
between the potential energy of the pendulum and the energy
remaining in the pendulum after impacting the specimen. The impact
energy is corrected for friction and air-resistance losses.
Price RM50
31
NUMERICAL LISTING
Standards Number Price (RM) Page Standards Number Price (RM) Page
MS 148 : Part 1 : 1973 30 29 MS 1151 : Part 2 : 1992 20 22

MS 149 : 1992 20 30 MS 1155 : 2003 20 27
MS 150 : 1999 10 28 MS 1156 : 1989 20 20
MS 224 : 2005 20 28 MS 1157 : Part 16 : 1992 20 3
MS 281 : Part 1 : 1999 10 1 MS 1157 : Part 18 : 1992 10 4
MS 281 : Part 2 : 1998 10 1 MS 1157 : Part 19 : 1992 10 4
MS 281 : Part 3 : 1998 10 1 MS 1157 : Part 22 : 1991 10 4
MS 281 : Part 4 : 1999 10 1 MS 1157 : Part 24 : 1991 20 4
MS 281 : Part 5 : 1998 10 1 MS 1157 : Part 27 : 1993 30 4
MS 281 : Part 6 : 1998 10 1 MS 1157 : Part 29 : 1992 20 4
MS 281 : Part 10 : 1999 10 1 MS 1157 : Part 31 : 1992 20 4
MS 281 : Part 11 : 1999 10 1 MS 1157 : Part 34 : 1991 10 4
MS 281 : Part 12 : 2001 10 1 MS 1157 : Part 35 : 1991 20 4
MS 281 : Part 14 : 2001 20 1 MS 1157 : Part 38 : 2005 10 4, 18
MS 281 : Part 15 : 1992 10 2 MS 1157 : Part 39 : 1991 10 4
MS 281 : Part 16 : 1999 10 2 MS 1157 : Part 40/1 : 1999 20 5
MS 297 : 1981 10 2 MS 1157 : Part 40/2 : 1999 10 5
MS 298 : 1985 50 2 MS 1157 : Part 41 : 1999 20 2, 5
MS 317 : 1986 10 2 MS 1208 : 2005 10 30
MS 463 : 1994 20 3 MS 1225 : Part 1 : 2004 30 27
MS 466 : 1987 20 2 MS 1225 : Part 2 : 2006 30 27
MS 506 : 1977 (2004) 20 1 MS 1267 : 1992 10 16
MS 511 : 1977 60 3 MS 1268 : 1992 10 21
MS 562 : 1978 (2002) 50 30 MS 1269 : 1992 10 16
MS 602 : 1979 30 22 MS 1271 : 1992 10 9
MS 671 : Part 1 : 2002 20 3 MS 1272 : Part 1 : 1993 10 9
MS 671 : Part 2 : 1992 20 20 MS 1272 : Part 2 : 1992 20 9
MS 672 : 1999 40 19, 27 MS 1274 : 1992 20 9
MS 676 : 2001 10 27 MS 1291 : 2003 20 27
MS 679 : 1999 20 19, 27 MS 1292 : 1992 10 5
MS 681 : 1980 30 22 MS 1295 : 1992 30 30
MS 735 : 1996 20 27 MS 1303 : Part 1 : 1993 30 16
MS 773 : 1999 30 19, 20,26, MS 1312 : 1993 10 21
MS 868 : 1999 20 20, 29 MS 1332 : 1993 50 18
MS 876 : 1984 30 30 MS 1334 : 1993 20 16
MS 908 : 1984 20 30 MS 1336 : 1993 20 15
MS 973 : 2002 10 27 MS 1337 : 1993 20 19
MS 974 : 2002 10 20 MS 1339 : 1993 10 21
MS 976 : 2004 20 19 MS 1343 : Part 1 : 1993 10 16
MS 978 : 1985 40 20, 25 MS 1343 : Part 2 : 1993 20 16
MS 979 : Part 1 : 1985 40 20, 25 MS 1344 : 1993 20 21
MS 979 : Part 2 : 1985 30 20, 25 MS 1345 : 1993 20 9, 15
MS 1010 : 1986 30 1,25 MS 1348 : 2005 10 30
MS 1012 : 2003 20 16 MS 1349 : 1994 20 9, 15
MS 1013 : 1986 10 3 , 16 MS 1359 : Part 4 : 1994 10 2
MS 1068 : 2002 10 27 MS 1359 : Part 5 : 1994 10 2
MS 1070 : 2002 20 26 MS 1359 : Part 6 : 1994 10 2
MS 1082 : 1994 20 20 MS 1359 : Part 7 : 1995 10 2
MS 1097 : 2005 10 30 MS 1359 : Part 8 : 1995 10 2
MS 1105 : 1988 20 22 MS 1371 : 1995 20 9, 16
MS 1106 : 1988 20 20 MS 1385 : 1996 20 21
MS 1151 : 1989 10 22 MS 1392 : 1998 10 2
MS 1151 : Part 1 : 2005 10 19 MS 1394 : 1996 20 30
MS 1400 : 1996 20 21
MS 1405 : 1996 10 21
32
NUMERICAL LISTING
MS 1558 : 2002 10 21
MS 1406 : 1996 20 9 MS 1559 : 2002 20 23
MS 1407 : Part 1 : 1996 30 27 MS 1560 : 2002 20 21
MS 1407 : Part 2 : 1996 30 27 MS 1563 : 2002 30 30
MS 1407 : Part 3 : 2001 30 28 MS 1564 : Part 1 : 2003 30 28
MS 1407 : Part 4 : 2001 20 28 MS 1564 : Part 2 : 2003 30 28
MS 1418 : 1997 20 19 MS 1564 : Part 3 : 2002 30 28
MS 1420 : 1997 10 23 MS 1564 : Part 4 : 2002 30 28
MS 1421 : 2005 40 9 MS 1564 : Part 5 : 2002 20 28
MS 1422 : 1997 10 23 MS 1564 : Part 6 : 2002 10 28
MS 1423 : 1997 20 23 MS 1565 : 2002 20 29
MS 1424 : 1997 10 21, 23 MS 1566 : 2002 10 29
MS 1439 : 1998 20 30 MS 1567 : Part 1 : 2002 20 29
MS 1440 : 1998 150 8 MS 1568 : Part 7 : 2002 20 5
MS 1441 : 1998 10 9 MS 1582 : 2003 20 21
MS 1442 : 1998 10 9 MS 1593 : 2003 20 21
MS 1443 : 1998 10 29 MS 1594 : 2003 20 22
MS 1444 : 1998 10 29 MS 1733 : 2004 40 22
MS 1449 : Part 1 : 1999 20 5 MS 1734 : 2004 20 22
MS 1449 : Part 3 : 1999 20 5 MS 1735 : 2004 20 22
MS 1449 : Part 4 : 1999 20 5 MS 1736 : Part 1 : 2004 20 25
MS 1449 : Part 5 : 1999 20 5 MS 1736 : Part 2 : 2004 20 25
MS 1449 : Part 6 : 1999 20 5 MS 1736 : Part 3 : 2004 20 25
MS 1465 : Part 1 : 1999 20 9 MS 1736 : Part 5 : 2004 20 25
MS 1465 : Part 2 : 1999 20 10 MS 1736 : Part 7 : 2004 50 25
MS 1466 : 1999 20 10 MS 1737 : 2004 30 25
MS 1467 : 1999 10 10 MS 1738 : 2004 10 25
MS 1468 : 1999 20 10 MS 1739 : 2004 10 25
MS 1469 : 1999 10 10 MS 1740 : 2004 10 26
MS 1470 : 1999 10 10 MS 1741 : 2004 10 26
MS 1473 : 1999 10 10 MS 1761 : 2004 10 26
MS 1476 : 1999 20 10 MS 1769 : 2004 10 22
MS 1477 : 1999 20 23 MS 1770 : 2004 20 22
MS 1478 : 1999 20 23,29 MS 1771 : 2004 20 22
MS 1479 : 1999 20 23,29 MS 1772 : Part 1 : 2004 20 23
MS 1501 : 2000 30 8 MS 1772 : Part 2 : 2004 20 23
MS 1502 : 2000 30 28 MS 1805 : 2005 40 23
MS 1504 : 2000 10 19 MS 1806 : 2005 50 23
MS 1505 : 2005 40 23 MS 1807 : 2005 40 23
MS 1509 : 2000 10 23 MS 1808 : 2005 40 10
MS 1510 : 2000 20 28 MS 1809 : 2005 40 18
MS 1521 : 2001 20 28 MS 1810 : 2005 40 30
MS 1523 : 2001 10 5 MS 1811 : 2005 50 19
MS 1524 : 2001 20 5 MS 1812 : 2005 50 19
MS 1528 : Part 1 : 2001 30 18 MS 1813 : 2005 40 16
MS 1530 : 2001 10 28 MS 1856 : 2005 40 19
MS 1541 : 2002 10 2 MS 1857 : 2005 40 20
MS 1542 : 2002 20 2 MS 1858 : 2005 10 20
MS 1545 : 2002 10 26 MS 1871 : 2005 20 18
MS 1546 : 2002 20 5 MS 1872 : 2005 10 18
MS 1547 : 2002 10 5 MS 1896 : 2005 40 24
MS 1548 : 2002 10 5 MS 1897 : 2005 40 24
MS 1549 : 2002 10 3 MS 1898 : 2005 40 24
MS 1550 : 2002 10 3 MS 1899 : 2005 40 24
MS 1556 : 2002 20 21 MS 2000 : 2005 50 24
MS 1557 : 2002 20 21 MS 2001 : 2005 50 24
33
NUMERICAL LISTING
MS ISO
MS ISO 1209-2 : 1997 10 19
MS ISO 1210 : 1995 20 12
MS ISO 34-2 : 1999 20 6
MS ISO/TR 1326 : 1995 10 12
MS ISO 36 : 2002 10 3
MS ISO 1403 : 2002 10 26
MS ISO 37 : 1998 20 6
MS ISO 1431-2 : 1999 20 7
MS ISO 48 : 2002 30 6
MS ISO 1432 : 2000 10 7
MS ISO 60 : 2004 10 10
MS ISO 1433 : 2000 20 7
MS ISO 62 : 2001 20 10
MS ISO 1628-1 : 2004 30 12
MS ISO 75-1 : 1999 10 10
MS ISO 1628-2 : 2004 20 12
MS ISO 75-2 : 1999 10 10
MS ISO 1629 : 2004 10 29
MS ISO 75-3 : 1999 10 10
MS ISO 1675 : 1995 10 13
MS ISO 132 : 2002 20 6
MS ISO 1798 : 1998 10 13
MS ISO 175 : 2001 30 11
MS ISO 1817 : 2002 30 7
MS ISO 176 : 2001 10 11
MS ISO 1853 : 2002 20 7
MS ISO 177 : 2001 10 11
MS ISO 1873 : Part 1 : 1994 10 17
MS ISO 178 : 2004 30 11
MS ISO 1873 : Part 2 : 1994 10 17
MS ISO 179-1 : 2002 30 11
MS ISO 1926 : 1997 10 19
MS ISO 179-2 : 2002 30 11
MS ISO 2039-1 : 2004 20 13
MS ISO 180 : 2002 20 11
MS ISO 2285 : 1999 10 7
MS ISO 188 : 2001 20 6
MS ISO 2393 : 2000 20 7
MS ISO 247 : 2001 10 6
MS ISO 2528 : 2000 20 24
MS ISO 287 : 1999 10 6
MS ISO 2555 : 1995 20 13
MS ISO 289-1 : 1998 20 6
MS ISO 2561 : 1998 10 17
MS ISO 289-2 : 1998 10 6
MS ISO 2578 : 1995 30 13
MS ISO 291 : 2000 20 11
MS ISO 2580 : Part 1 : 1994 10 17
MS ISO 294-1 : 2002 30 16
MS ISO 2580 : Part 2 : 1999 20 17
MS ISO 294-2 : 2002 10 16
MS ISO 2782 : 1999 20 7
MS ISO 294-3 : 2002 20 16
MS ISO 2818 : 1995 20 13
MS ISO 294-5 : 2004 20 17
MS ISO 2897-1 : 2001 10 17
MS ISO 296 : 2001 10 3
MS ISO 2897-2 : 1999 20 17
MS ISO 305 : 2001 10 11, 8
MS ISO 2898-1 : 2001 10 17
MS ISO 489 : 1998 10 8, 11
MS ISO 2898-2 : 1999 20 17
MS ISO 498 : 2002 10 3
MS ISO 2921 : 2001 10 7
MS ISO 527 : Part 1 : 1994 20 11,17
MS ISO 3146 : 2004 20 13
MS ISO 527 : Part 2 : 1994 10 11,17
MS ISO 3167 : 2003 20 13
MS ISO 527 : Part 3 : 2001 10 24
MS ISO 3821 : 2002 20 26
MS ISO 527 : Part 4 : 2001 20 24
MS ISO 3383 : 1998 10 7
MS ISO 527 : Part 5 : 2001 20 24
MS ISO 3384 : 2002 20 7
MS ISO 604 : 2003 30 11
MS ISO 3865 : 1999 20 7
MS ISO 780 : 2001 20 6
MS ISO 4000-1 : 2002 30 30
MS ISO 813 : 1999 20 6
MS ISO 4570-1 : 2002 10 29
MS ISO 815 : 1998 20 6
MS ISO 4570-2 : 2002 10 29
MS ISO 844 : 1998 20 8, 12
MS ISO 4570-3 : 2002 20 29
MS ISO 868 : 2004 20 12
MS ISO 4582 : 2001 30 13
MS ISO 877 : 2001 30 8
MS ISO 4589-1 : 2000 20 13
MS ISO 899-1 : 1999 20 12
MS ISO 4589-2 : 2000 30 17
MS ISO 899-2 : 1999 20 12
MS ISO 4607 : 1995 20 13
MS ISO 974 : 2003 20 12
MS ISO 4610 : 2004 20 18
MS ISO 1043-1 : 2004 20 12
MS ISO 4613-2 : 1999 10 18
MS ISO 1043-2 : 2004 10 12
MS ISO 4642 : 2004 10 27
MS ISO 1043-3 : 2004 20 12
MS ISO 4648 : 1998 10 7
MS ISO 1043-4 : 2004 10 12
MS ISO 4661-1 : 1998 10 8
MS ISO 1158 : 2002 20 17
MS ISO 4665 : 2002 20 8
MS ISO 1183 : 1995 20 12
MS ISO 4892-1 : 1998 20 13
MS ISO 1209-1 : 1997 10 19
MS ISO 4892-2 : 1998 20 13
34
NUMERICAL LISTING
Standards Number Price (RM) Page
MS ISO 4892-3 : 1998 20 13

MS ISO 4892-4 : 1998 20 13
MS ISO 6252 : 1999 20 14
MS ISO 6427 : 1997 20 14,22
MS ISO 6471 : 2000 20 8
MS ISO 6502 : 2002 30 3
MS ISO 6603-1 : 2003 30 14
MS ISO 6603-2 : 2003 30 14
MS ISO 6762 : 2002 10 29
MS ISO 7111 : 1998 10 14
MS ISO 7391-1 : 2001 20 18
MS ISO 7391-2 : 1999 20 18
MS ISO 7619 : 2000 20 8
MS ISO 8013 : 2005 140 8
MS ISO 8256 : 1999 30 14
MS ISO 8570 : 2004 20 24
MS ISO 8789 : 2005 90 8
MS ISO 8985 : 2000 30 18
MS ISO 9026 : 1998 20 8
MS ISO 9413 : 2002 80 29
MS ISO 10508 : 2004 30 20
MS ISO 11346 : 1999 10 8
MS ISO 11357-1 : 1999 20 14
MS ISO 11357-2 : 2003 20 14
MS ISO 11357-3 : 2003 20 14
MS ISO 11357-5 : 2004 20 14
MS ISO 11357-6 : 2004 20 14
MS ISO 11357-7 : 2004 20 14
MS ISO 11424 : 2002 20 20
MS ISO 11425 : 2004 20 20
MS ISO 13007-1 : 2005 20 30
MS ISO 13007-2 : 2005 50 31
MS ISO 13468-1 : 2004 20 14
MS ISO 13468-2 : 2004 20 14
MS ISO 13586 : 2003 30 15
MS ISO 13802 : 2004 50 31
MS ISO 14782 : 2004 20 15
MS ISO 15512 : 2004 20 15
MS ISO 15605 : 2003 20 31
MS ISO 15850 : 2004 30 15
MS ISO 15876-1 : 2004 20 26
MS ISO 15876-2 : 2004 30 26
MS ISO 15876-3 : 2004 30 26
MS ISO 15876-5 : 2004 20 26
MS ISO 15876-7 : 2004 30 26
MS ISO 16014-1 : 2004 30 15
MS ISO 16014-2 : 2004 20 15
MS ISO 16014-3 : 2004 20 15
MS ISO 16014-4 : 2004 20 15
MS ISO 17281 : 2004 30 15
35
INDEX
Subject - MS Number - Page Subject - MS Number - Page
A Flexible packaging material

Adhesives - Part 1 : Absolute methods (MS 1772:Pt.1),23
- Bonding decorative thermoset laminates (MS 1563),30 - Part 2 : Industrial methods (MS 1772:Pt.2),23
- For ceramic tiles and mosaics (MS 1295),30 Floor mats - Rubber, For vehicles (MS 1068),27
- Glossary (MS 562),30
- Phenolic & aminoplastic, for plywood (MS 908),30
- Pressure sensitive PVC, Electrical purpose (MS 876),30 G
- Sampling (MS ISO 15605),31
Ammonia, Anhydrous & aqueous (MS 506),1 Gas
Automotive lamps – Plastic lenses (MS 1469),10 - Chromatography - Residual vinyl chloride monomer
(MS 1013),3, 16
B
Bearings
- Materials of elastomeric bridge bearings (MS 671:Pt.1),3
H
- Design & installation, Code of practice (MS 671:Pt.2),20
Hose
Buckets (Containers) – Plastics (MS 676),27
- Air and vacuum systems (MS ISO 11424),20
- Gas welding equipment (MS ISO 3821),26
C
Cellular plastics L
- Tensile properties (MS ISO 1926),19
- Bending test (MS ISO 1209-1),19 Latex - Test methods (MS 466),2
- Flexural properties (MS ISO 1209-2),19
- Rigid materials (MS ISO 844), 8, 12
Cold water storage M
- Feed expansion cisterns (MS 1225:Pt. 1),27
- 600 gal capacity (MS 1225:Pt.2),27 Marine fenders - Rubber materials (MS 1385),21
Cushion Gum (MS 1348),30 Mattresses, Latex foam rubber
Ceramic tiles - For domestic & general use (MS 679),19, 27
- Grouts and adhesives Measuring equipment, domestic purposes
- Terms and definitions (MS ISO 13007-1), 30 - Cup, spoon and litre measure (MS 1560),21
- Test methods Mobile waste containers
- Adhesives (MS ISO 13007-2),31 - Part 1 : Two wheels, 80 L – 390 L (MS 1564:Part 1),28
- Part 2 : Four wheels, 500 L – 1200 L (MS 1564:Part 2),28
D - Part 3 : Four wheels,
Disposable polystyrene cutlery (MS 1502),28 - 770 L – 1300 L, dome lids, trunnion and/or comb lifting
(MS 1564:Part 3),28
- Part 4 : Four wheels,
F - 750 L – 1700 L, flat lids, Wide trunnion and/or BG
(MS 1564:Part 4),28
Feeding bottles (Babies) – Plastics (MS 735),27
Films (Materials) – PVC (MS 681),22 - Part 5 : test method and performance requirements
Film hardness, organic coating (MS 1509),23 (MS 1564:Part 5),28
Flexible cellular materials - Part 6 : safety and health requirement (MS 1564:Part 6),28
- Slabs, bonded, molded urethane foams (MS 1332),18 Motor vehicle
- Flexible cellular materials (MS ISO 1798),13 - PVC floor mat (MS 1470),10
- Flexible cellular materials (MS 1809),18 - Rubber floor mat (MS 1068),27
Flexible plastics laminates Motorcycles
- Determination of thickness (MS 1504),19 - Tyre dimensions and rims, Inch code (MS 1565),29
- Bond strength (MS 1505),23
36
Index
N - Low-temperature method (MS ISO 16014-3),15

- High-temperature method (MS ISO 16014-4),15
Natural rubber latex concentrate - Barcol Hardness Impressor (MS 1808),10
- Alkalinity (MS 281:Pt.4),1 - Beverage containers (MS 1476),10
- Boric acid content (MS 281:Pt.12),1 - Bond strength (MS 1505),23
- Coagulum content (MS 281:Pt.6),1 - Brittleness temperature (MS ISO 974),12
- Centrifuged or creamed, ammonia-preserved types - Burning behavior by oxygen index (MS ISO 4589-1),13
(MS ISO 296),3 - Burning behavior – Ambient – Temperature test
- Dry films (MS ISO 498),3 (MS ISO 4589-2),17
- Dry rubber content (MS 281:Pt.3),1 - Coding system (MS 1405),21
- KOH number (MS 281:Pt.11),1 - Compressive properties (MS ISO 604),11
- Mechanical stability (MS 281:Pt.5),1 - Composite materials (MS 1812),19
- pH (MS 281:Pt.16),2 - Short-beam strength (MS 1811),19
- Sampling (MS 281:Pt.1),1 - Containers
- Total nitrogen (MS 281:Pt.14),1 - Packaging (MS 1733),22
- Total solid content (MS 281:Pt.2),1 - Blow-moulded thermoplastic (MS 1735),22
- Viscosity (MS 281:Pt.15),2 - Density & relative density of non-cellular plastics
- Volatile fatty acid number (MS 281:Pt.10),1 (MS ISO 1183),12
Natural rubber – Inner tubes for motor vehicles (MS 868),20, 29 - Deflection under load
Natural rubber products – Extractable proteins (MS 1392),2 - General test method (MS ISO 75-1),10
- Plastics and ebonite (MS ISO 75-2),10
- Determination of,
O - Haze (MS ISO 14782),15
- Water content (MS ISO 15512),15
Open-mouth sacks, polyolefin woven (MS 1521),28 - Hardness
- Part 1 : Ball identification method
(MS ISO 2039-1),13
P - Determination
- Burning behaviour of horizontal & vertical
Pacifiers (Babies) (MS 1156), 20 (MS ISO 1210),12
Packaging, Code of practice - Flammability & burning rate (MS ISO/TR 1326),12
- Pictorial marking (MS ISO 780),6 - Time temperature limits (MS ISO 2578),13
Paper, Method for the determination - Melting behaviour (MS ISO 3146),13
- Moisture content determination (MS ISO 287),6 - Changes in colour & variations in properties
Pipe fittings (MS ISO 4582),13
- Plastic waste pipe & fittings (MS 978),20, 25 - Differential scanning calorimetry (MS ISO 11357-1),14
- Unplasticised PVC sewerage pipe & fittings - Glass transition temperature
(MS 979:Pt. 1),20, 25 (MS ISO 11357-2),14
- Unplasticised PVC, Underground sewerage pipe & fittings -Temperature and enthalpy of melting and
(MS 979:Pt. 2),20, 25 crystallization (MS ISO 11357-3),14
Plastics - Reaction-curve temperature and times
- Acrylonitrile/butadiene/styrene (MS ISO 11357-5),14
- Designation (MS ISO 2580:Pt.1),17 - Oxidation induction time (MS ISO 11357-6),14
- Preparation of test specimens (MS ISO 2580:Pt.2),17 - Crystallization kinetics (MS ISO 11357-7),14
- Adhesive bonds (MS 1810),30 - Ethylene, environmental stress (MS 1371),9, 16
- Amorphous thermoplastic - Ethylene/vinyl acetate (E/VAC)
- Test specimens - Preparation of test specimens & properties
- Bars (MS 1343:Pt.1),16 (MS ISO 4613-2),18
- Plates (MS 1343:Pt.2),16 - Ethylene/vinyl acetate copolymer (EVAC) thermoplastics
- Average molecular mass - Determination of vinyl acetate content
- General principles (MS ISO 16014-1),15 (MS ISO 8985),18
- Universal calibration method (MS ISO 16014-2),15 - Environmental stress cracking (MS ISO 6252),14
37
Index
- Film - Non-instrumented (MS ISO 6603-1),14

- Parallel plate method (MS 1423),23 - Instrumented (MS ISO 6603-2),14
- Package yield (MS 1424),21, 23 - Puncture propagation (MS 1806),23
- Film and sheeting - Preparation of glass fibre reinforced (MS 1337),19
- Cold-crack temperature (MS ISO 8570),24 - Rigid cellular plastics materials (MS 1528:Pt.1),18
- Force required (MS 1151:Pt.2),22 - Resins in liquid or emulsion or dispersions (MS ISO 2555),13
- Tear resistance (MS 1151-1),19 - Tensile-impact strength (MS ISO 8256),14
- Mechanical scanning (MS 1339),21 - Tensile creep (MS ISO 899-1),12
- Wetting tension (MS 1420),23 - Three point bending (MS 1473),10
- Test for haze (MS 1421),9 - Transparent plastics
- Unrestrained linear thermal shrinkage (MS 1422),23 - Single-beam instrument (MS ISO 13468-1),14
- Transmission of oxygen gas (MS 1734),22 - Double-beam instrument (MS ISO 13468-2),14
- Fracture toughness (MS ISO 17281),15 - Soluble matter
- LEFM method (MS ISO 13586),15 - General principles (MS ISO 1628-1),12
- Tension fatigue crack (MS ISO 15850),15 - Symbols
- Flexural creep by three-point loading (MS ISO 899-2),12 - Basic polymer (MS ISO 1043:Pt. 1),12
- Glossary (MS 1440),8 - Fillers and reinforcing materials (MS ISO 1043:Pt. 2),12
- Flexural properties (MS ISO 178),11 - Pasticizer (MS ISO 1043:Pt. 3),12
- Shore (MS 1271),9 - Flame retardants (MS ISO 1043:Pt. 4),12
- Ball indentation (MS 1272:Pt.1),9 - Shrink tension (MS 1807),23
- Rockwell (MS 1272:Pt.2),9 - Thermoplastics materials
- Gas transmission rate (MS 1344),21 - Compression moulding (MS 1334),16
- Guidelines for the standardization of methods-Viscosity - Injection moulding (MS ISO 294-1),16
(MS ISO 1628/1),12 - Small tensile bars (MS ISO 294-2),16
- Glass fibre reinforced (MS 1418),19 - Small plates (MS ISO 294-3),16
- Hardness - Investigating anisotropy (MS ISO 294-5),17
- Plasticized poly (vinyl chloride) PVC-P - Thermosetting materials, Compression moulding
- Designation systems & basis for specifications (MS 1336),15
(MS ISO 2898-1),17 - Tensile creep (MS 1345),9, 15
- Preparation of test specimens & determination of - Thermal stability, discoloration methods (MS ISO 305),11, 8
properties (MS ISO 2898-2),17 - Vinyl chloride homoplymers and copolymer
- Polycarbonate (PC) moulding - Clorine content (MS ISO 1158),17
- Test specimens & determination of properties - WC seats (MS 976),19
(MS ISO 7391-2),18 Plastics container, specification
- Designation system (MS ISO 7391-1),18 - Capacity, mass and tolerances or dimensions
- High-strength thermosetting laminates (MS ISO 75-3),10 (MS 1407:Pt. 2),27
- Ignition loss of cured reinforced resins (MS 1813),16 - Screw thread (MS 1407:Pt. 1),27
- Impact-resistant polystyrene (PS-I) - Container capacity, 5 L to 60 L (MS 1407:Pt.3),28
- Designation systems & basis for specifications - Drums, 70 L - 250 L capacity (MS 1407:Pt.4),28
(MS ISO 2897-1),17 - Drainability (bottles and jars) (MS 1858),20
- Preparation of test specimens & determination of Plastics, Charpy impact properties
properties (MS ISO 2897-2),17 - Non-instrumented impact test (MS ISO 179-1),11
- Liquid resins-Density & relative density (MS ISO 1675),13 - Instrumented impact test (MS ISO 179-2),11
- Method of exposure to natural weathering Plastics, Determination of tensile properties
(MS ISO 4607),13 - General principles (MS ISO 527:Pt. 1), 11, 17
- Measuring shrinkage (MS 1501),8 - Test conditions for moulding and extrusion plastics
- Multipurpose test (MS ISO 3167),13 (MS ISO 527:Pt. 2), 11,17
- Matter extractable (MS ISO 6427),14, 22 Plastics – Flexible cellular materials (MS 1809),18
- Open – Flame carbon-Arc lamps (MS ISO 4892-4),13 Plastics film
- Preparation of test specimens by machining - Extraction by chemicals (MS 1805),23
(MS ISO 2818),13 - Puncture propagation (MS 1806),23
- Puncture impact, rigid plastics - Shrink tension (MS 1807),23
Plastics food containers, lids (MS 1558),21
38
Index
Plastics, Liquid chemicals

- Guidance for the assessment of conformity
- Effects of immersion (MS ISO 175),11
(MS 1736:Part 7),25
Plastics, Laboratory light sources
- Thermoplastic pipes, installation (MS 1737),25
- General guidance (MS ISO 4892-1),13
- Thermoplastics pipes, temperature cycling
- Xenon-arc sources (MS ISO 4892-2),13
(MS 1739),25
- Fluorescent UV lamps (MS ISO 4892-3),13
Plastics, polyethylene tank
- Open – Flame carbon - arc lamps (MS ISO 4892-4),13
- Cold water storage (MS 1225:Part 1),27
Plastics washing basins, domestic use (MS 1530),28
Plastic piping system
Plastics lockable containers, household wares (MS 1557),21
- Tubular test pieces (MS 1738),25
Plastics, Plasticizers
- Test method for leaktightness (MS 1740),26
- Activated carbon method, loss (MS ISO 176),11
Plastics tableware (MS 1556),21
- Determination of migration (MS ISO 177),11
Plastics, water absorption (MS ISO 62),10
Plastics, Tensile properties
Pneumatic passengers car tyres (MS 149),30
- Films and sheets (MS ISO 527-3),24
Pneumatic tyres (MS 148:Pt. 1),29
- Isotropic and orthotropic fiber-reinforced composites
- Retreads, For motor vehicles (MS 224),28
(MS ISO 527-4),24
- Pneumatic tyres (MS 1439),30
- Undirectional fibre-reinforced composites
Polyethylene
(MS ISO 527-5),24
- Carbon black dispersion (MS 1442),9
Plastic lenses – Automotive lamps (MS 1469),10
Polyethylene container
Plastics resistivity- Volume (MS 1465:Pt 2),10
- Environmental stress-crack- blow-moulded (MS 1582),21
- Surface (MS 1465:Pt 1),9
Polyethylene film – Low density (MS 1478),23, 29
Plastics moulding - Code of practice for system of tolerances for
Polyethylene Sheeting-Construction, industrial & agricultural
dimension (MS 1406),9
applications (MS 1479),23, 29
Plastic, Method of test
Polyethylene film
- Abrasion resistance (MS 1897),24
- Determination of 2% secant modulus (MS 1467),10
- Changes in colour & appearance (MS ISO 4582),13
- Free falling dart method (MS 1105),22
- Determination of flexural properties of rigid plastics
Polyethylene Film & Sheeting (MS 1477),23
(MS 1349), 9, 15
Polyethylene tanks – 600 gal (MS 1225:Pt.2),27
- Environmental stress crack (MS 1593),21
Polyethylene terephthalate (PET) bottles
- Exposure to solar radiation (MS ISO 877),8
- 24-hour gas (air) space acetaldehyde content
- Hot seal strength (MS 1899),24
(MS 1468),10
- Izod impact strength (MS ISO 180),11
Polypropylene and propylene - copolymer thermoplastics
- Load containment (MS 1896),24
- Designation (MS ISO 1873:Pt. 1),17
- Peel cling (MS 2001),24
- Preparation of test specimens (MS ISO 1873:Pt. 2),17
- Protrusion puncture (MS 1898),24
Polymers - Cable insulation & sheaths, Test methods
- Standard atmospheres (MS ISO 291),11
- Thermogravimetric measurements (MS ISO 7111),14
- Temperature of deflection under load (MS 1274),9 Polymeric materials
- Water vapor transmission rate (MS 2000),24 - Compression set (MS 1871), 18
Plastics piping system, hot and cold water - Humid conditions (MS 1872), 18
- Polybutylene Polystrene – Residual styrene monometer (MS ISO 2561),17
- Fittings (MS ISO 15876-3),26 Polystyrene cushioning foams (MS 1510),28
- Fitness for purpose of the system Polyurethane foam, high-resilience (MS 1268),21
(MS ISO 15876-5),26 Precured tread (MS 1208),30
- General (MS ISO 15876-1),26 PVC
- Guidance for the assessment of conformity - Film (MS 681),22
(MS ISO 15876-7),26 - Rigid PVC (MS 1010),1, 25
- Pipes (MS ISO 15876-2),26 - Resin (MS 1012),16
Crosslinked polyethylene (PE-X) - Floor mats – motor vehicles (MS 1470),10
- General (MS 1736:Part 1),25
- Pipes (MS 1736:Part 2),25 R
- Fittings (MS 1736:Part 3),25
- Fitness for purpose of the system Radiator hose - Rubber, For automobile (MS 1070),26
(MS 1736:Part 5),25 Raw rubber – Green strength (MS ISO 9026),8
39
Index
Raw natural rubber, test methods for technically specified - Test methods (MS ISO 3383),7
- Colour (MS 1359:Pt. 5),2 - Hardness test (MS ISO 815),6
- Dirt content (MS 1542),2 - Pocket hardness meters (MS ISO 7619),8
- Mooney viscosity (MS 1359:Pt. 4),2 - Vulcanized, thermoplastic, ageing and heat resistance
- Rapid plasticity and plasticity retention (MS 1359:Pt. 6),2 (MS ISO 188),6
- Volatile matter (MS 1548),5 - Vulcanized, temperature-retraction characteristics
- Mooney Accelerated Storage Hardening (MASHT) (MS ISO 2921),7
(MS 1359:Pt. 7),2 Rubber hose
- Wallace Accelerated Storage Hardening (WASHT) - Agricultural spraying (MS 1545),26
(MS 1359:Pt. 8),2 - Non-collapsible (MS ISO 4642),27
Residual vinyl chloride monomer (MS 1013 ),3,16 Rubber hoses and hose assemblies
Retread tyres - Pneumatic, For motor vehicles (MS 224),28 - Automotive power-steering systems (MS ISO
Rubber 11425),20
- Achieving elevated or subnormal temperature Rubber latices
(MS ISO 3383),7 - Natural, Evaporated preserved (MS 317),2
- Atomic absorption spectrometry - Nomenclature (MS ISO 1629),29
- Copper content (MS 1449:Pt 3),5 Rubber latex concentrate
- Iron content (MS 1449:Pt 5),5 - Alkalinity (MS 281:Pt.4),1
- Zinc content (MS 1449:Pt 1),5 - Boric acid content (MS 281:Pt.12),2
- Method-Manganese content (MS 1449:Pt 4),5 - Coagulum content (MS 281:Pt.6),1
- Magnesium content (MS 1449:Pt 6),5 - Dry rubber content (MS 281:Pt.3),1
- Metal content - KOH number (MS 281:Pt.11),2
- Determination of calcium content - Mechanical stability (MS 281:Pt.5),1
(MS 1568:Pt.7),5 - pH (MS 281:Pt.16),2
- Bands (MS 973),27 - Sampling (MS 281:Pt.1),1
- Curemeters (MS ISO 6502),3 - Sludge content (MS 1541),2
- Crystallization (MS 1546),5 - Total solid content (MS 281:Pt.2),1
- Determination of ash (MS ISO 247),6 - Temperatures of 5 – 40 degrees celcius (MS 1547),5
- Elastomeric teats (MS 1082),20 - Total nitrogen content (MS 281:Pt.14),1
- Flexible tubing & hose, For LPG installation - Volatile fatty acid number (MS 281:Pt.10),1
(MS 773),19, 20, 26 - Viscosity (MS 281:Pt.15),2
- Gloves Rubber test mixes – Equipment & procedures
- For medical examination & diagnostic (MS 1155),27 (MS ISO 2393),7
- Surgical (MS 1291),27 Rubber threads - Test methods (MS 1400),21
- Residual powder Rubber tread, Compund (MS 1097),30
- Power free (MS 1549),3 Rubber tyre – Determination of tyre plunger energy (MS
- Powdered rubber (MS 1550),3 1444),29
- Hoses - Radiator, for automobiles (MS 1070),26 Rubber, Unvulcanized
- Measurement of resistivity (MS ISO 1853),7 - Mooney viscosity (MS ISO 289-1),6
- Raw natural (MS 297),2 - Pre-vulcanization characteristics (MS ISO 289-2),6
- Raw natural, Sampling (MS 298),2
- Rubber teat-Volatile nitrosamines (MS 1312),21
- Rubber thread - For retreating automobile tyre S
(MS 1097),30
- Rubber seals – Water supply, drainage & sewerage Sacks - Polyethylene, Heavy-duty (MS 1106),20
pipelines (MS 672),19, 27 Safety
- Rubber, vulcanized, methods of test (MS ISO 3865),7 Seal, Strength – Flexible barrier (MS 1441),9
- Resistance to weathering (MS ISO 4665),8 Sealing rings - Rubber, For water supply & drainage pipeline
- Seeds, for commercial planting (MS 463),3 (Withdrawn) (MS 672),19, 27
- Seals-water stops, materials (MS 1292),5 Seasonings see also Condiments
- Solvent extract (MS 1524),5 Seeds
- Swimming fins (MS 974),20 - Rubber, For commercial planting (MS 463),3
- Physical tests (MS ISO 4661-1),8
40
Index
- Determination of tear strength

Sheet materials - Trouser, angle and crescent test pieces
- PVC, Thick (MS 602),22 (MS 1567:Pt.1),29
- Water vapour transmission rate, Gravimetric method - Small (delft) test pieces (MS ISO 34-2),6
(MS ISO 2528),24 - Estimation of life-time & maximum temperature
Solid materials – Determination of linear thermal expansion (MS ISO 11346),8
(MS 1466),10 - Low temperature stiffening (Gehman test)
Surgical rubber gloves, single use (MS 1291),27 (MS ISO 1432),7
- Measurements (MS ISO 4648),7
- Tensile stress – Strain properties (MS ISO 37),6
T - Temperature rise (MS 1157:Pt 41),2, 5
- Textile fabrics (MS ISO 36),3
Tear tests - Methods of test
- Plastic films & sheetings (MS 1151-2),22 - Preferred gradations of properties (MS ISO 1433),7
- Tear resistance (MS 1151-1),19 - Staining in contact with organic material
Test method (MS ISO 3865),7
- Plastics tighted drums (MS 1856),19 - Preparation of samples
- Threaded plastics closures (MS 1857),20 - Physical tests (MS ISO 4661-1),8
Textile-reinforced rubber water hose (MS ISO 1403),26 - Chemical test (MS 1157:Pt.39),4
Thermoplastic containers - Time-interval (MS 1523),5
- Blown, column crush properties (MS 1594),22 - Abrasion resistance
- Packaged reagents / proprietary products (MS 1559),23 - Rotating cylindrical drum device (MS 1157:Pt 40/1),5
Thermoplastics pipes - Abrasive wheel (MS 1157:Pt 40/2),5
- Hot and cold water systems (MS ISO 10508),20 - Adhesion to
Thermoplastics rubber - Rigid plates (MS 1157: Pt. 19),4
- Tensile stress-strain properties (MS ISO 37),6 - Wire cord (MS 1157: Pt. 31),4
Thermoplastic road marking materials (MS 1303: Pt. 1),16 - Metal two-plate (MS 1157: Pt. 38),4, 18
Thermoplastic, Method of test for plastics - Rigid substrate – 90 degrees peel method
- Melt flow index (MS 1267),16 (MS ISO 813),6
- Vicat softening temperature (MS 1269),16 - Ageing characteristics (MS 1157:Pt. 34),4
Transparent Plastics – Refractive Index (MS ISO 489),8, 11 - Hardness (MS ISO 48),6
Tubes (Tyres) - Inner tubes for motor vehicles (MS 868),20, 29 - Tension set (MS ISO 2285),7
Tyres (MS 149),30 - Accelerated ageing
- Pneumatic, Retread, For motor vehicles (MS 224),28 - Flex cracking (MS ISO 132),6
- Pneumatic, for highway vehicles (MS 1394),30 - Permeability (MS ISO 2782),7
- Passenger car and rims (MS ISO 4000-1),30 - Resistance to ozone cracking (MS 1157:Pt.16),3
- Tubeless, Test methods (MS 150),28 - Indentation hardness (MS ISO 7619),8
- Solid tyres (MS 1566),29 - Modulus in shear (MS 1157:Pt.18),4
- Valves - Effect of liquids (MS ISO 1817),7
- ISO core chamber No.2 (MS ISO 6762),29 - Density (MS 1157:Pt.22),4
- Dimension and designation (MS ISO 9413),29 - Antistatic & conductive products (MS 1157:Pt.24),4
- Valve threads - Rebound resilience (MS 1157:Pt.27),4
- 5V1, 5V2, 6V1 and 8V1 (MS ISO 4570-1),29 - Static adhesion (MS 1157:Pt.29),4
- 9V1, 10V1, 12V1 and 13V1 (MS ISO 4570-2),29 - Compressed stress relaxation (MS ISO 3384),7
- 8V2, 10V1, 11V1, 13V2, 15V1, 16V1, 17V1, 17V2, - Tension fatigue (MS 1157:Pt.35),4
17V3, 19V1, 20V1 (MS ISO 4570-3),29
V W
Vulcanized rubber Water tanks - 600 gal (MS 1225:Pt.2),27
- Creep tests (MS ISO 8013), 8
- Crystallization effect under compression (MS ISO 6471),8 Z
- Dynamic strain test (MS ISO 1431-2),7 Zinc oxide - For use in rubber (MS 511),3
41
ORDER FORM
The Malaysian Standards listed in this catalogue can be purchased from SIRIM Berhad, Technical Information
and Intellectual Property Services Department and can be ordered by mail, fax or e-mail.
For ordering purposes, please use the order form below.
Name : ____________________________________________
Company Name : _________________________________________
Address & Tel / Fax / E-mail : ________________________________
________________________________________________________
Malaysian Standards Number (MS No.) Unit Price* Quantity Cost (RM)
TOTAL
Postage & Handling Charges ( 10% of total or RM5.00 whichever is more )
GRAND TOTAL
* For oversea order, please contact SIRIM Berhad for prices.
Enclosed is a cheque no. ___________________ dated __________________ amounting
RM ____________ for the above order. ( Cheque is to be made payable to SIRIM Berhad )
____________________________ ___________________
Signed & Company Stamp Date
Send to : SIRIM Berhad, Technical Information & Intellectual Property Services Department,
1, Persiaran Dato’ Menteri, Section 2, 40000 Shah Alam, MALAYSIA
Tel : ++6 03 - 5544 6118 / 6105 / 6112; Fax : ++ 6 03 - 5544 6114 / 5544 6146
E-mail : isd_resource@sirim.my
Attention : Manager

11-Rubber & Plastics

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

11-Rubber & Plastics

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

11-Rubber & Plastics

Uploaded by

Copyright:

Available Formats

MALAYSIAN STANDARDS

RUBBER & PLASTICS INDUSTRIES

Department of Standards Malaysia

Tel : 603-8885 8000

ISC A - Food and Agriculture

List of Sectorial Catalogue 2007

MS ISO : Malaysian Standard which is identical to International Organization for

MS.....(P) : Provisional Standard

01. Generalities. Terminologies. Standardization 61. Clothing Industry.

03. Sociology. Services. Company Organization 65. Agriculture.

19. Testing. 79. Wood Technology.

25. Manufacturing Engineering. 87. Paint and Colour Industries.

31. Electronics. 93. Civil Engineering.

33. Telecommunications. Audio and Video 95. Military Engineering.

37. Image Technology.

39. Precision Mechanics. Jewellery.

43. Road Vehicles Engineering.

45. Railway Engineering.

47. Shipbuilding and Marine Structures.

49. Aircraft and Space Vehicle Engineering.

53. Materials Handling Equipment.

55. Packaging and Distribution of Goods.

59. Textile and Leather Technology.

RUBBER & PLASTICS INDUSTRIES

Manufacturing processes in the rubber and plastics industries ------------------------------------------ 1

Numerical Listing ---------------------------------------------------------------------------------------------------- 32

MS 506 : 1977 (2004) MS 281 : Part 10 : 1999

MS 281 : Part 1 : 1999 MS 281 : Part 11 : 1999

MS 281 : Part 4 : 1999

MS 1359 : Part 4 : 1994 MS 1541 : 2002

MS ISO 296 : 2001

MS ISO 498 : 2002

83.040.20 Rubber compounding ingredients MS 1157 : Part 16 : 1992

MS ISO 4665 : 2002

MS ISO 8789 : 2005 MS ISO 844 : 1998

MS 1274 : 1992 MS 1442 : 1998

MS 1466 : 1999 MS 1808 : 2005

MS 1269 : 1992 MS ISO 294-1 : 2002

MS ISO 294-3 : 2002

MS ISO 294-5 : 2004 MS ISO 2580 : Part 1 : 1994

MS ISO 7391-2 : 1999 MS 1871 : 2005

83.100 Cellular materials

MS 1157 : Part 38 : 2005

83.140.01 Rubber and plastics products in MS 1082 : 1994

MS 1344 : 1993 MS 1560 : 2002

MS ISO 527-3 : 2001

MS ISO 527-4 : 2001

MS 1736 : Part 3 : 2004

MS 1225 : Part 1 : 2004

83.140.99 Other rubber and plastics products MS 1225 : Part 2 : 2006

MS 1407 : Part 4 : 2001 MS 1564 : Part 5 : 2002

MS 1564 : Part 3 : 2002

MS 1564 : Part 4 : 2002

MS 1444 : 1998 MS ISO 4570-2 : 2002

MS 1479 : 1999 MS ISO 9413 : 2002

MS 1565 : 2002 83.160.10 Road vehicle tyres

MS 1567 : Part 1 : 2002

MS 562 : 1978 (2002)

MS ISO 15605 : 2003

Enclosed is a cheque no. _ dated amounting