Predetermined Motion Time Systems (PMTS)

Predetermined Motion Time
Systems (PMTS)
CHAPTER 10
Predetermined Motion Time Systems
 Predetermined motion time system (PMTS) is a work
measurement technique whereby times established for basic human
motions are used to build up the time for a job at a defined level of
performance.
 PMTS also called predetermined time system (PTS), is a database

of basic motion elements and their associated normal time values,
together with a set of procedures for applying the data to analyze
manual tasks and establish standard times for the tasks.
 The PMTS database is most readily conceptualized as a set of tables

listing time values that correspond to the basic motion elements, the
lowest level in our hierarchy of manual work activity
 They include motions such as reach, grasp, move, and release.

The Predetermined Motion Time
Systems Concept
· The concept is similar to constructing a building. A
building is composed of elements-Doors, walls, beams,
bricks, plumbing. The structure is the sum of the elements.
· Likewise, a job is also considered to consist of elements, the
total of which is the sum of the elements.
· In formal words, the assumption is that each job element is
independent and additive; that is, each element does not
affect what happens before or after it - independence and
additivity.
What are Predetermined Motion
Time Systems?
· A collection of basic motion times.
· Technique for obtaining a standard time by:

· analyzing and subdividing a task into elemental
motions
· assigning pre-set standard times for motions and
summing these to obtain a standard time for the
whole task.
Popular Predetermined Motion Time
Systems
· Methods -Time Measurement
· Work-Factor
· Predetermined Time Standards Systems –

Meyers
· MOST
Methods Time Measurement
(MTM)
· MTM is a procedure which analyzes any manual operation
or method into the basic motions required to perform it,
and assigns to each motion a predetermined time standard
which is determined by the nature of the motion and the
conditions under which it is made.
· MTM gives values for the fundamental motions of:
reach, move, turn, grasp, position, disengage, and release.

Methods Time Measurement
(MTM)
· Most predetermined motion time systems use time measurement
units (TMU) instead of seconds for measuring time. One TMU is
defined to be 0.00001 hours, or 0.036 seconds. These smaller units
allow for more accurate calculations without the use of decimals. 1 hr
= 100,000 TMU
· MTM studies provided the following kinds of information
· Developing effective work methods prior to production
· Improving existing methods to increase production and decrease labor cost
per unit
· Establishing time standards as basis for wages and incentive plans
· Developing time formulas or standard data for future use
· Guiding product design for most efficient manufacture
· Developing effective tool designs for most efficient manufacture

Advantages of PMTS systems
PMT systems offer a number of advantages over stop-watch time
study. With PMT systems one time is indicated for a given
motion, irrespective of where such a motion is performed.
 A PMT system, which avoids both rating and direct observation,

can lead to more reliability in setting standard times.
 PMT systems are not too difficult to apply and can be less time
consuming than other methods.
 PMT systems are particularly useful for very short repetitive time
cycles such as assembly work in the electronics industry.
PMTS Levels and Generations
Chronologically, first-level PMT systems were the first to be
developed, and then second - and higher - level systems were
subsequently constructed based on the first-level systems.
Because of this chronological development of the systems, the

level of the system usually corresponds to the generation of the
system.
First-level PMT systems are called first generation systems, and

the subsequent systems are second and third generations.
For example, MTM-1 is first generation MTM-2 is second

generation and is based on MTM-1. MTM-3 is a third generation
MTM system.
Characteristics of PMT system levels
Work Systems and the Methods, Measurement, and

Management of Work
by Mikell P. Groover, ISBN 0-13-140650-7.
©2007 Pearson Education, Inc., Upper Saddle River, NJ.
All rights reserved.
MTM-1
 In our hierarchy of work activity, MTM-1 operates at the basic
motion element level, as illustrated in Figure 14.1.
 Most of the MTM-1 basic motions involve hand and arm
movements, although elements are also provided for eye, leg,
foot, and body actions.
 Time units in MTM are called TMUs (time measurement units).
 MTM was developed by studying motion pictures of work activity,

and the time units for MTM were originally defined as the time
per frame of motion picture film, and defined as
 1 TMU = 0.00001 hr = 0.0006 min = 0.036 sec
 100,000 TMUs in 1 hour,
 1667 TMUs in 1 min, and
 27.8 TMUs in 1 sec.
 Table 14.3 defines the MTM-1 motion elements, and Table 14.4
presents a tabulation of their time values.
Figure 14.1 The position of MTM motion elements in our work hierarchy.
Management of Work
Management of Work
Management of Work
Management of Work
Management of Work
Other MTM Systems
Other members of the MTM family satisfy various user

needs.
MTM-2 – Second-level PMTS in which basic motion
elements are combined into motion aggregates
 GET – combines Reach and Grasp

 PUT – combines Move and Position
MTM-3 – Third-level PMTS which has four motion categories
1. Handle
2. Transport
3. Step and foot motions
4. Bend and arise
Management of Work
Maynard Operation Sequence
Technique (MOST)
The Maynard Operation Sequence Technique
(MOST) is a high-level predetermined motion time
system (PMTS) that is based on MTM.
MOST is a work measurement technique that
concentrates on the movement of objects. It is used
to analyze work and to determine the normal time
that it would take to perform a particular process
/operation.
The basic version of MOST which is now referred to
as Basic MOST.
Maynard Operation Sequence Technique
(MOST)
More specifically, MOST is used to:
1. Break down the operation/process into smaller steps/units

2. Analyze the motions in each step/unit by using a standard
MOST method sequence

3. Assign indices to the parameters constituting the method
sequence for each task
4. Sum up the indices to arrive at a time value for each
step/unit
5. Sum up the time values for all the steps/units to arrive at
the ‘normal time’ required to perform that
MOST in the Work Pyramid
Figure 14.2 The position of the Basic MOST activity sequence model
in our work hierarchy
Basic MOST
 The focus of Basic MOST is on work activity involve the movement
of objects. The majority of industrial manual work does involve
moving objects (e.g., parts, tools) from one location to another in
the workplace.
 Basic MOST uses motion aggregates (collections of basic motion
elements) that are concerned with moving things. The motion
aggregates are called activity sequence models in Basic MOST.
 There are three activity sequence models in Basic MOST, each of
which consists of a standard sequence of actions:
 General move. This sequence model is used when an object is moved

freely through space from one location to the next (e.g., picking
something up from the floor and placing it on a table).
 Controlled move. This sequence model is used when an object is moved
while it remains in contact with a surface (e.g., sliding the object along
the surface) or the object is attached to some other object during its
movement (e.g., moving a lever on a machine).
 Tool use. This sequence model applies to the use of a hand tool (e.g., a
hammer or screwdriver).
 The actions in an activity sequence model, called sequence model parameters
in Basic MOST, are similar to basic motion elements in MTM. Let us examine
the three sequence models and indicate the standard sequence of model
parameters for each.
General Move. The General Move sequence is applicable when an object is

moved through the air from one location to another. There are four parameters
(actions) in the General Move, symbolized by letters of the alphabet:
 A — Action distance, usually horizontal. This parameter is used to describe
movements of the fingers, hands, or feet (e.g., walking). The movement can be
per formed either loaded or unloaded.
 B — Body motion, usually vertical. This parameter defines vertical body
motions and actions (e.g., sitting, standing up).
 G — Gain control. This parameter is used for any manual actions involving the
fingers, hands, or feet to gain physical control of one or more objects. ft is
closely related to the grasp motion element in MTM (e.g., grasp the object).
 P — Placement. The placement parameter is used to describe the action
involved to lay aside, position, orient, or align an object after it has been moved
to the new location (e.g., position the object).
 These parameters occur in the following standard sequence in the
General Move:
 where the first three parameters (A B G) represent basic motions to get

an object, the next three parameters (A B P) represent motions to put
or move the object to a new location, and the final parameter (A)
applies to any motions at the end of the sequence, such as return to
original position.
 To complete the activity sequence model, each parameter is assigned a
numerical value in the form of a subscript or index number that
represents the time to accomplish that action.
 The value of the index number depends on the type of action, its
motion content, and the conditions under which it is performed. Table
14.6 lists the parameters and possible circumstances for the action,
together with the corresponding values of the index numbers.
 When the index values have been entered for all parameters, the time
for the sequence model is determined by summing the index values
and multiplying by 10 to obtain the total TMUs. The procedure is
illustrated in the following example.
Example: General Move
 Develop the activity sequence model and determine the normal time
for the following work activity: A worker walks 5 steps, picks up a small
part from the floor, returns to his original position, and places the part
on his worktable.
 Solution: Referring to Table 14.6, the indexed activity sequence model for this
work activity would be the following:
A10 B6 G1 A10 B0 P1 A0
 where A10 = walk 5 steps, B6 = bend and arise, G1 = control of small part, A10 =
walk back to original position, B0 = no body motion, P1 = lay aside part on table,
and A0 = no motion. The sum of the index values is 28. Multiplying by 10, we
have 280 TMUs (about 10 sec).

Predetermined Motion Time Systems (PMTS)

Uploaded by

Copyright:

Available Formats

Predetermined Motion Time Systems (PMTS)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Predetermined Motion Time Systems (PMTS)

Uploaded by

Copyright:

Available Formats

Predetermined Motion Time

 PMTS also called predetermined time system (PTS), is a database

 The PMTS database is most readily conceptualized as a set of tables

 They include motions such as reach, grasp, move, and release.

· Technique for obtaining a standard time by:

· Methods -Time Measurement

· Predetermined Time Standards Systems –

reach, move, turn, grasp, position, disengage, and release.

· Improving existing methods to increase production and decrease labor cost

· Developing time formulas or standard data for future use

· Guiding product design for most efficient manufacture

· Developing effective tool designs for most efficient manufacture

 A PMT system, which avoids both rating and direct observation,

Because of this chronological development of the systems, the

First-level PMT systems are called first generation systems, and

For example, MTM-1 is first generation MTM-2 is second

Work Systems and the Methods, Measurement, and

 MTM was developed by studying motion pictures of work activity,

Other members of the MTM family satisfy various user

 GET – combines Reach and Grasp

MTM-3 – Third-level PMTS which has four motion categories

1. Break down the operation/process into smaller steps/units

MOST method sequence

 General move. This sequence model is used when an object is moved

General Move. The General Move sequence is applicable when an object is

 where the first three parameters (A B G) represent basic motions to get

Example: General Move

You might also like