Service Training

Self-study Programme 359

1.4l TSI Engine with Dual-charging

Design and Function

1
 The 1.4l TSI* engine is the world’s first petrol engine with direct petrol injection and dual-charging. Volkswagen is
thus laying another milestone in engine development.

* The term “TSI” is a protected abbreviation of Volkswagen.

S359_002

On the following pages, we will introduce you to the design and function of the new 1.4l TSI engine with dual-
charging.

NEW Important
Note

The self-study programme shows the design and For current testing, adjustment and repair
function of new developments. instructions,
The contents will not be updated. refer to the relevant service literature.

2
Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Engine mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Poly-V-belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Timing chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Cylinder block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cylinder head and valve train . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Dual-charging with supercharger and turbocharger . . . . . . . . . . . . . . . . . 11
Crankcase breather and ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Oil system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Dual-circuit cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Demand-regulated fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Engine Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
CAN networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Engine Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Actuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Functional Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Test Yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

3
 Introduction

Special Technical Features

The special concept behind this engine is, above all,
the combination of direct petrol injection, dual-
charging and downsizing.

- Volkswagen used direct petrol injection for the first

time in the Lupo FSI model year 2001.
- In dual-charging, the engine is charged by a
mechanical compressor and/or a turbocharger.

- Downsizing is replacing a large-capacity engine

with a powerplant with smaller displacement and/
or fewer cylinders. This reduces the internal friction
and this the fuel consumption without the power or
torque being reduced.
S359_003

Thanks to this concept, it has greater performance

than engines with the same output and also consumes
less fuel. It therefore meets customer demands for
economic FSI engines with a high level of dynamism.

Technical features
● Two output versions delivering 103kW and 125kW ● Plastic intake manifold
● Bosch Motronic MED 9.5.10 ● Continuous inlet camshaft timing adjustment
● Homogenous mode (Lambda 1) ● Grey cast iron cylinder block
● Double injection catalytic converter heating ● Steel crankshaft
● Turbocharger with waste gate ● Duo-centric oil pump
● Additional mechanical supercharger ● Dual-circuit cooling system
● Intercooler ● Fuel system regulated according to requirements
● Maintenance-free timing chain ● High-pressure fuel pump with a delivery pressure
● Engine cover with vacuum tank for the intake of up to 150 bar
manifold flap control

4
Technical data
Torque and power diagram
1.4l/103kW TSI engine 1.4l/125kW TSI engine
Nm kW Nm kW

rpm rpm

Torque [Nm] S359_093 Torque [Nm]

S359_094

Power [kW] Power [kW]

Technical data
Engine code BMY BLG
Type 4-cylinder in-line engine 4-cylinder in-line engine
Displacement 1390 1390
Bore 76.5 76.5
Stroke 75.6 75.6
Valves per cylinder 4 4
Compression ratio 10:1 10:1
Maximum output 103 kW at 6,000 rpm 125 kW at 6,000 rpm
Maximum torque 220 Nm at 1,500 – 4,000 rpm 240 Nm at 1,750 – 4,500 rpm
Engine management Bosch Motronic MED 9.5.10 Bosch Motronic MED 9.5.10
Fuel Super unleaded RON 95 Super Plus at RON 98
(Super unleaded at RON 95 with slightly
higher consumption and torque
reduction in the low rev ranges)
Exhaust gas treatment Main catalytic converter, Main catalytic converter,
Lambda control Lambda control
Emissions standard EU 4 EU 4

The different output and torque levels are achieved using software. The engine mechanics are the same
in both engines.

5
 Engine mechanics

Poly-V-belt drive
The 1.4l TSI engine has two poly-V-belts.

- The ancillary component drive belt is a six-groove poly-V-belt. It drives the coolant pump, the alternator and the
air-conditioning compressor from the camshaft pulley.
- The supercharger drive belt is a five-groove poly-V-belt. It drives the compressor via the magnetic clutch pulley
when the magnetic clutch is engaged.

A tensioning pulley ensures that the ancillary component and supercharger belts are correctly tensioned. The
tensioning pulley after the crankshaft pulley also ensures that the poly-V-belt runs correctly around the crankshaft
pulley and coolant pump pulley.

Supercharger Ancillary components

drive belt drive belt

Belt tensioner
Compressor belt
pulley

Alternator
belt pulley
Tensioning
pulley
Tensioning pulley

Coolant pump pulley

Pulley for supercharger magnetic
clutch N421
Air-conditioning
compressor
S359_004 belt pulley

Camshaft belt
pulley

6
Chain drive
Both the camshafts and also the oil pump are driven by the crankshaft via a maintenance-free timing chain.

Camshaft drive Oil pump drive

The toothed chain drive has been optimised due to the The oil pump is driven by a toothed chain with 8 mm
greater loading. The toothed chain has hardened pins pitch for improved sound.
and heavy-duty link plates that have been adapted to It is tensioned by a spring-loaded chain tensioner.
the chain forces.
The toothed chain is tensioned by a hydraulic chain
tensioner.

Sprocket for Outlet camshaft

inlet camshaft with vane sprocket
adjuster

Sprocket for Slide rail

camshaft drive

Tensioning rail Sprocket for driving

camshafts and oil pump

Hydraulic Spring-loaded
chain tensioner chain tensioner

Oil pump drive Oil pump sprocket

toothed chain

S359_005

Camshaft timing adjustment

A load- and engine speed-dependent vane adjuster The camshaft adjustment allows:
is used for the continuous inlet camshaft adjustment.
The adjustment range is a maximum 40° crank angle. - Very good internal exhaust gas recirculation and
- improved torque band.

7
 Engine Mechanics

Cylinder block
The cylinder block on the 1.4l TSI engine is made from grey cast iron with lamellar graphite. This guarantees
sufficient operating safety at the high combustion pressures of the TSI engine. Due to the high strength of a cylinder
block made from grey cast iron with lamellar graphite compared with one made from diecast aluminium,
the camshaft may be removed.

Cylinder lining

Outer wall

S359_006

As with the 1.4l/66kW and 1.6l/85kW FSI engines, the cylinder block has a so-called open-deck design. This means
that there are no webs between the outer wall and the cylinder lining.

This has two advantages:

- No air bubbles can form in this area which would lead to ventilation and cooling problems particularly with the
dual-circuit cooling system,
- When the cylinder head is bolted to the cylinder block, the cylinder liner deformation caused by the decoupling
of the cylinder liner and cylinder block is less and more even than with a closed-deck design with webs. This
results in lower oil consumption as the piston rings compensate this deformation better.

You will find further information on the 1.4l/66kW and 1.6l/85kW FSI engines in self-study programmes
296 “The 1.4l and 1.6l. FSI engine with timing chain” and 334 “The fuel system in
FSI engines”.

8
Crankshaft drive
The crankshaft drive consists of the crankshaft, the connecting, the bearing shell, the piston and the piston pin.
Several modifications have been made to the crankshaft drive as the forces occurring on the 1.4l TSI engine are
considerably higher than with the previous FSI engines.

Piston

Piston pin
Coated piston
skirt

Connecting rod

Camshaft

S359_007

Piston

The pistons are made from diecast aluminium. The friction of the piston package has been reduced
A combustion chamber recess with a deflector has by a graphite coating on the piston skirt and a greater
been worked into the piston base. This leads to a skirt-to-wall clearance of 55 µm.
strong swirling of the intake air and thus to a very
good mixture formation.
The outlet side of the piston is cooled with a piston The piston pin diameter has been increased from 17 to
cooling system. The jets open at 2.0 bar. 19 mm due to the high ignition pressure.

Camshaft Connecting rod

The forged crankshaft is made from steel and is stiffer The connecting rods are fracture-split. Therefore only
than the cast crankshaft on the the same two components fit together, they are cheap
1.4l/66kW FSI engine. to produce and good positive engagement is formed.
Above all, this reduces the noises from the engine.

9
 Engine Mechanics

Cylinder head and valve train

The cylinder head is the same as on the 1.4l/66kW FSI Cylinder head
engine except for a few modifications.

Several changes have been made to the valve train

due to the greater loads and exhaust gas
temperatures.

● Due to the higher loads, the outlet valves are

reinforced on the valve seats and the valve springs
are heat-treated.
● Due to the higher exhaust gas temperatures, the
outlet valves are filled with sodium for better heat
transfer. This reduces the temperature at the outlet
valves by approx. 100°C.
Outlet valve Inlet valve S359_008

Camshaft case

The camshafts, which are mounted on three bearings, High-pressure Camshaft case
are inserted into the camshaft case. Their axial play is fuel pump

limited by the cover and the camshaft case.

Roller tappet

The high-pressure fuel pump is bolted to the camshaft

case. It is driven by a double cam on the inlet
camshaft. Due to the higher injection pressures and
the fuel quantities to be delivered compared with
previous FSI engines, the pump stroke has been
increased from 5 to 5.7 mm. The friction is reduced by
a roller tappet between the high-pressure fuel pump
and camshaft and halves the drive moment of the
high-pressure fuel pump.
S359_097
Inlet camshaft Pump cam

The seal between the camshaft case and

cylinder head is formed with a liquid
gasket. Please note the repair instructions in
ELSA.

10
Dual-charging with supercharger and turbocharger
Current charged engines mostly use turbochargers. The 1.4l TSI engine is the first to use a combination of
supercharger and turbocharger. That means the engine is charged by a supercharger in addition to the
turbocharger depending on the torque requirements.

Supercharger
The supercharger is a mechanical charger that is
activated by a magnetic clutch.

Advantages:

- Faster build up of boost pressure

- High torque at low revs
- Only activated when required
- No external lubrication and cooling necessary

Disadvantages:

- Requires drive power from engine

- Boost pressure is produced at any engine speed
S359_009
and is then regulated with part of the generated Mechanical
power being lost again supercharger

Turbocharger Turbocharger

The turbocharger is constantly powered by the

exhaust gas.

Advantages:

- Very good efficiency due to use of exhaust gas

energy

Disadvantages:

- In a small engine, the boost pressure produced in

the low rev ranges is not sufficient to generate high
torque
- High thermal loading

S359_092

11
 Engine Mechanics

Schematic diagram of all supercharging components

The schematic diagram shows the basic set-up of the “dual-supercharging” system and the path of the fresh intake
air.

Regulating flap Mechanical Intake manifold pressure sender G71 with

control unit J808 supercharger intake air temperature sender G42

Supercharger Fresh air

drive belt

Intake manifold
pressure sender
(supercharger) G583 Air filter
with intake air
Intake manifold
temperature sender
G520 Throttle valve
module J338

Magnetic clutch Charge air pressure sender

G31 with intake air
temperature sender G299

Intercooler
Ancillary
components drive Charge pressure
belt control solenoid valve N75
Exhaust manifold

Catalytic
converter

Pressure
canister
Exhaust
gas

Turbocharger air Turbocharger Waste gate flap S359_010

recirculation valve N249

Air is drawn in through the air filter. The air flows from the turbocharger via the intercooler
The position of the regulating flap is defined in the and the throttle valve module into the intake manifold.
regulating flap control unit determining whether the
air flows via the supercharger and/or straight to the
turbocharger.

12
Working ranges of the supercharging components
The diagram shows the working ranges of the mechanical supercharger and the turbocharger. Depending on the
torque requirements, the engine control unit determines whether the required boost pressure is generated and, if
yes, how. The turbocharger works during the all of the coloured areas. The exhaust gas power is not sufficient in the
lower rev ranges to produce the required boost pressure on its own, however.

Constant boost range of supercharger

From a minimum torque requirement and up to an engine speed of 2,400 rpm, the supercharger is
constantly activated. The supercharger boost pressure is controlled via the regulating flap control unit.

Requirement-dependent boost range of supercharger

Up to a maximum engine speed of 3,500 rpm, the supercharger is activated when necessary. This is, for
example, necessary when the car is driven at a constant speed in this range and then accelerates quickly.
Due to the slow response of the turbocharger, acceleration would be delayed (turbo lag). Therefore the
supercharger is activated and the required boost pressure is reached as quickly as possible.

Exclusive turbocharger boost range

In the green area, the turbocharger manages to produce the necessary boost pressure on its own. The
boost pressure is controlled by the charge pressure control solenoid valve.
Torque [Nm]

Engine speed [rpm]

S359_011

13
 Engine Mechanics

Implementation of working ranges

Depending on the load and rev range, the engine control unit calculates how the required quantity of fresh air
should reach the cylinder to create the required torque. It determines whether the turbocharger can produce the
boost pressure on its own or whether the compressor needs to be activated.

Naturally aspirated mode at low load

Regulating flap
control unit J808
The regulating flap is fully open in naturally aspirated
mode. The intake air flows via the regulating flap
control unit to the turbocharger. The turbocharger is
already driven by the exhaust gas, but the exhaust
gas energy is so low that it only produces a small
Throttle valve
boost pressure.
module J338
The throttle valve is opened depending how far the
driver presses the accelerator and there is a vacuum
in the intake manifold.

Turbocharger S359_015

Supercharger and turbocharger operation at higher

loads and engine speeds up to 2,400 rpm Supercharger

Intake manifold pressure Regulating flap

In this range, the regulating flap is closed or partly sender (supercharger) control unit J808
opened to regulate the boost pressure. The G583
supercharger is activated via a magnetic clutch and is
driven by the supercharger drive belt. The
supercharger draws in air and compresses it. The
compressed fresh air is pumped by the supercharger
to the turbocharger. There the compressed air is
Throttle valve
compressed even more.
module J338
The boost pressure of the supercharger is measured
by the intake manifold pressure sender G583 and Charge air pressure
regulated by the regulating flap control unit. The sender G31
overall boost pressure is measured by the charge air
pressure sender G31.
The throttle valve is completely open. A pressure of up
to 2.5 bar (absolute) is built up in the intake manifold.
Magnetic
clutch
Turbocharger S359_016

14
Turbocharger and supercharger operation at high
loads and revs between 2,400 and 3,500 rpm Supercharger Regulating flap
control unit J808
In this range, the boost pressure is produced at, for
example, constant speed, by the turbocharger alone.
If the car now accelerates quickly, the turbocharger
would be too slow to generate the boost pressure fast
enough. There would be turbo lag. To avoid this, the
engine control unit activates the supercharger briefly Throttle valve
module J338
and adjusts the regulating flap control unit according
to the required boost pressure. It helps the
turbocharger produce the necessary boost pressure.

Magnetic
clutch
Turbocharger S359_017

Turbocharger operation Supercharger Regulating flap

control unit J808

From an engine speed of approx. 3,500 rpm, the

turbocharger can produce the required boost
pressure on its own at any load point.
The regulating flap is fully open and the intake air
flows straight to the turbocharger. The exhaust gas Throttle valve
energy is now sufficient in all conditions to produce module J338
the boost pressure with the turbocharger.
Charge air pressure
The throttle valve is completely open. A pressure of up sender G31
to 2.0 bar (absolute) is built up in the intake manifold.
The boost pressure of the turbocharger is measured
with the charge air pressure sender G31 and
regulated by the charge pressure control valve.
Magnetic Charge pressure
clutch control solenoid
valve N75
S359_033
Turbocharger

15
 Engine Mechanics

Supercharger
Pulley for magnetic
Supercharger drive clutch for supercharger
Supercharger Coolant pump
The supercharger is activated as required and is drive belt pulley

driven by the coolant pump via an auxiliary drive.

The auxiliary drive is activated with a maintenance-
free magnetic clutch on the coolant pump module.
Due to the ratio of the crankshaft belt pulley to the
supercharger belt pulley as well as a internal
supercharger gear ratio, the supercharger turns at
five times the crankshaft speed. The maximum speed
of the supercharger is 17,500 rpm.

Supercharger

Compressor belt Camshaft belt

pulley Tensioning pulley
pulley

S359_014

The supercharger may not be opened.

The chamber containing the speed step
gear and the synchronous gear is filled
with oil. It is filled for life.

Rotors S359_037

Synchronous gear Speed step gear

Mechanical supercharger Rotors

The mechanical supercharger is bolted to the cylinder

block on the intake manifold side after the air filter.
Due to the shape of its two compressor rotors, it is also
called a twin-screw supercharger.
The boost pressure is controlled via a regulating flap
control unit. The maximum boost pressure that the
supercharger produces is about 1.75 bar (absolute).

Pressure side Suction side

S359_023

16
How it works:

Supercharger function
Pressure side Suction side
The two supercharger rotors have been designed so
Rotors Mechanical
that, when they rotate, the space on the intake side supercharger
becomes larger. The fresh air is drawn in and
transferred to the pressure side of the supercharger
by the rotors.
On the pressure side, the chamber between the two
supercharger rotors becomes smaller again. The air is
pushed towards the turbocharger.

From
Regulating flap air filter
control unit J808
S359_019

To turbocharger

Supercharger boost pressure regulation

Pressure side Suction side
Intake manifold pressure
The boost pressure is regulated by the position of the sender (supercharger)
regulating flap. When the regulating flap is closed, G583 with Mechanical
the supercharger produces the maximum boost intake air temperature supercharger
sender G520
pressure at this engine speed. The compressed fresh
air is pumped to the turbocharger. If the boost
pressure is too high, the regulating flap is opened
slightly. Now part of the intake air is sent to the
turbocharger and the rest via the partly opened
regulating flap to the intake side of the supercharger.
The boost pressure is reduced. On the intake side, the
air is drawn in again and compressed. This relieves
supercharger and the required drive power for the From
Regulating flap air filter
supercharger is reduced. The boost pressure is
control unit J808
measured by the intake manifold pressure sender S359_013
(supercharger) G583.
To turbocharger

17
 Engine Mechanics

Noise insulation of supercharger

Due to the arrangement of the supercharger in the direction of the passenger cell, the remaining noises can be
heard by the occupants. Several measures have been taken to reduce the noise level.

To keep the mechanical noise from the supercharger To reduce the noises upon intake and compression ...
low ...
- both sides (fill and discharge side) of the
- the gearing has been modified, e.g. meshing angle supercharger have been sound-proofed,
and twisting play, - the supercharger has been encapsulated and the
- the supercharger shafts have been stiffened and housing parts also lined with insulating foam.
- the supercharger case has been reinforced with
special ribs.

Sound-proofing on fill Housing

side

Insulating foam

Insulating foam Sound-proofing on

discharge side

Housing Supercharger Supercharger

S359_104 drive belt

Supercharger Magnetic clutch

During fast acceleration, the supercharger When the magnetic clutch is switched off,
can “whine” at rev ranges between three leaf springs pull the friction plate back
2,000 – 3,000 rpm. This is the normal to the starting position.
turbine-like operating noise of a Due to the high forces, a normal “clicking”
supercharger. of the magnetic clutch can occur. This can
occur up to an engine speed of 3,400 rpm.

18
Turbocharger system components
Turbocharger module Turbocharger
module
The turbocharger forms a module with the exhaust Turbocharger air Oil connection
manifold. recirculation valve
Both are made from highly heat-resistant cast steel
due to the exhaust gas temperatures.
The turbocharger has been incorporated in the
cooling system to protect the shaft bearings from high
temperatures. A circulating pump ensures that the
turbocharger does not overheat for up to 15 minutes
after the engine has been turned off. This prevents
steam bubbles forming in the cooling system.
The shaft bearings are connected to the oil system for
lubrication.
Furthermore the electrical recirculation valve for the
turbocharger and a pressure canister for boost
pressure limitation with the waste gate are part of the
turbocharger module. Pressure canister for boost Coolant connection
pressure limitation

Waste gate
S359_020

Exhaust manifold Turbocharger Exhaust manifold

Up to now in petrol engines, the mixture was enriched

early due to the high exhaust gas temperatures.
The exhaust manifold on the 1.4l TSI engine is
designed for exhaust gas temperatures up to
1,050 °C. As a result, the engine can be run with a
high boost pressure and with Lambda 1 in almost all
map ranges.

S359_021

19
 Engine Mechanics

Intercooler
The TSI engine uses an intercooler. This means that the charge air flows through a cooler and releases its heat via
the aluminium fins. These are cooled by the surrounding air.

Regulating flap Turbocharger From turbocharger Intercooler

control unit J808

Throttle valve
module J338

From supercharger
or from the
regulating flap
control unit

To throttle valve
module S359_024

Once the intake air has passed the turbocharger, it is very hot. It is heated to up to 200°C mainly by the
compression process, but also by the high temperature of the turbocharger.
As a result, the air has a lower density and less oxygen will reach the cylinder. Cooling the air to just above the
ambient temperature, will increase the density and more oxygen is fed to the cylinders.
Furthermore the knocking tendency and the production of nitrogen oxide are reduced.

20
Crankcase breather and ventilation
Crankcase breather
The crankcase breather allows the crankcase to be rinsed out and thus reduces the formation of water in the oil.
The breather is in the form of a hose from the air filter to the camshaft housing.

Crankcase ventilation
Unlike conventional naturally-aspirated engines, the crankcase ventilation system for a charged engine is more
complex. While there is a constant vacuum in the intake manifold of a naturally aspirated engine, it is up to 2.5 bar
(absolute) in the TSI engine.

Oil separation Oil separator To the check valve for the

crankcase breather
The gases are drawn out of the crankcase by the
vacuum.
In the labyrinth and in the cyclone oil separator, the
oil is separated from the gases and drips back into the
oil sump. Gases

Gases are sent to the intake air as follows Oil return S359_025

The gases flow from the timing chain case to the check
valve for the crankcase ventilation. To intake manifold
Depending on whether the pressure is lower in the with throttle

intake manifold or in front of the regulating flap From valve body To intake manifold
control unit, the return valve will open and allow the
gases to pass through. In the intake manifold or in
front of the regulating flap control unit, the gases mix
with the intake air and
are fed to the combustion chamber.
A throttle in the connecting hose to the intake
manifold limits the throughput when the vacuum
pressure becomes too high in the intake manifold. A
pressure regulating valve is therefore no longer
necessary.
Check valve for S359_086
crankcase breather

21
 Engine Mechanics

Oil supply
Oil filter Turbocharger
Oil circuit
The oil circuit differs from the one used in the
1.6l/85kW FSI engine because of the turbocharger
and the piston cooling system.

Colour legend

Oil pickup

Oil send

Piston cooling
Oil return nozzles

Regulated Oil return

duo-centric oil pump
S359_026
Oil pickup

Oil pump drive

The duo-centric oil pump is bolted to the bottom of the Crankshaft sprocket Steel spring for
cylinder block and is driven by the crankshaft via a chain tensioner

maintenance-free toothed chain.

Due to the exhaust gas turbocharger and the piston
cooling system, a greater oil delivery volume is
required. This has been achieved with a greater
transmission ratio from the crankshaft sprocket to the
oil pump sprocket.
The chain is tensioned by a steel spring on the chain
tensioner.

Toothed chain

S359_027

Oil pump sprocket

22
Regulated duo-centric oil pump
The regulated duo-centric oil pump has been taken from the current FSI engines. The oil pressure of 3.5 bar is
regulated with the oil delivery quantity over almost the whole rev range.
This has the following advantages:

- the drive power of the oil pump is reduced by up to 30%,

- the oil quality is not affected so much as less oil is circulated,
- the oil foaming in the oil pump is minimised because the oil pressure is the same across the whole rev range.

Oil pressure below 3.5 bar Discharge side Fill side

Outer rotor
The control spring presses the control ring against the
oil pressure (yellow arrows). The outer rotor also turns
with the control ring and thus enlarges the space To the
oil circuit Inner rotor
between the inner and outer rotor. As a result, more
oil is transported from the fill to the discharge side
and pushed into the oil circuit. The oil pressure also
increases with the oil quantity.

Control ring
Control spring S359_028

From the oil sump

Oil pressure above 3.5 bar Discharge side Fill side

Outer rotor
The oil pressure (yellow arrows) presses the control
ring against the control spring. The outer rotor is also
rotated in the direction of the arrows and the space To the
oil circuit Inner rotor
between the inner and outer rotor becomes smaller.
As a result, less oil is transported from the fill
to the discharge side and pushed into the oil
circuit. The oil pressure also decreases with the oil
quantity.

Control ring
Control spring S359_029

From the oil sump

23
 Engine Mechanics

Dual-circuit cooling system

The cooling system development is to a great extent the same as that used with the 1.6l/85kW FSI engine in the
Golf. It is a dual-circuit cooling system with separate coolant flow and different temperatures due to the cylinder
block and cylinder head.
In the cylinder head, the coolant is sent from the outlet to inlet side. An even temperature level is thus reached in the
cylinder head. This method is called crossflow cooling.

Reservoir Throttle Heat exchange for heating system

Coolant pump
Thermostat 1 from
cylinder head
(opens at 80° C)

Auxiliary heating
Coolant
distributor housing
Cylinder block
coolant circuit
Thermostat 2 from
cylinder head
(opens at 95° C)
Cylinder head
coolant circuit
Oil cooler

Turbocharger
Throttle

Coolant
circulation pump V50 Radiator S359_030

Compared with the 1.6l/85kW FSI engine the following has changed:

- due to a greater transmission ratio, the delivery - a coolant circulation pump V50 has been added,
quantity of the coolant pump has been increased - coolant flows through the turbocharger,
and sufficient heating power obtained at idle, - the exhaust gas recirculation valve is not required.
- thermostat 1 in the coolant distributor housing is a
two-stage type,

24
Dual-circuit cooling system
Thermostat 2 Cylinder head
The cooling system is divided into two circuits in the cooling circuit
engine. Around a third of the coolant in the engine
flows to the cylinders and two thirds to the combustion
chambers in the cylinder head.

The dual-circuit cooling system has the following

advantages:
- The cylinder block warms up faster because the
coolant remains in the cylinder block until 95°C is
reached. Thermostat 1

- Less friction in the crankshaft drive due to the

higher temperature level in the cylinder block.
- Better cooling of the combustion chambers due to
the lower temperature level of 80°C in the cylinder Cylinder block S359_031
head. This achieves better filling with a lower cooling circuit
knocking tendency.

Coolant distributor housing with two-stage thermostat

Due to the high coolant delivery quantity, there is a

high system pressure in the cooling system at high
revs. The two-stage thermostat 1 also opens at the
Thermostat 1
exact temperature in these conditions.
If a single-stage thermostat was used, a large
thermostat plate would have to be opened against the
high pressure. Due to the counteracting forces, the
thermostat would only open at high temperature,
however.
The two-stage thermostat only opens a small
thermostat plate at first when the opening
temperature is reached. The counterforces are lower
due to the smaller surface and the thermostat opens
at the exact temperature. After a specific path, the
small thermostat plate moves a larger plate and the
maximum possible cross-section is opened.
Thermostat plate
stage 1 Thermostat plate
stage 2

Stage 1 S359_032

Stage 2

25
 Engine Mechanics

Demand-regulated fuel system

The demand-regulated fuel system has been taken from the 1.6l/85kW FSI engine.
It has the advantage that both the electrical fuel pump and the high-pressure fuel pump only deliver the amount of
fuel required by the engine at that moment. This reduces electrical and mechanical drive power of the fuel pumps
and fuel is saved.

As the engine control unit checks the control of the electrical fuel pump, the fuel pressure sender for low
pressure is not required.
In each driving cycle, the delivery amount of the electrical fuel pump is throttled once until a certain
pressure can no longer be maintained in the high-pressure fuel system. The engine control unit now
compares the PWM signal (pulse-width modulation) to control the electrical fuel pump with the PWM
signal stored in the engine control unit. The signal is adjusted in the engine control unit if there are
deviations.

Low-pressure fuel system High-pressure fuel system

Door contact switch for Onboard supply control unit J519,

fuel pump supply voltage supply for
fuel pump supply

Engine control unit J623 Fuel pressure sender G247

Battery

Leakage line Pressure limiting valve

(opens at 172.5 bar)
Fuel pump
control unit J538
Fuel distributor
Return Throttle

Fuel filter with

pressure limitation valve

Fuel pressure
regulating valve N276 S359_081

High-pressure
fuel pump

Fuel pump G6 Fuel tank Injectors for cylinders 1-4

N30 - N33

Pressure free 0.5 to 6.5 bar 50 to 150 bar

26
Exhaust system
The exhaust gases are treated by a three-way catalytic converter. To ensure quick warm-up of the catalytic
converter despite the heat loss via the turbocharger, the connecting pipe between the turbocharger and the
catalytic converter has air-gap insulation.
The Lambda probe in front of the catalytic converter is a step-type Lambda probe. It is mounted in the inlet funnel
of the three-way catalytic converter, which is located near the engine. Due to this arrangement, it is exposed evenly
to the exhaust gas from all cylinders. At the same time, a fast start of the Lambda regulation is reached.

Resonator

Connecting pipe
with
air-gap insulation
Rear silencer

Turbocharger with
exhaust manifold

Exhaust pipe

Exhaust pipe with flexible

decoupling element

Step-type Lambda
probe in front of
catalytic converter G39
Step-type Lambda probe with
after catalytic converter Lambda probe heater
G130 with Lambda probe Three-way
catalytic converter Z19
heater after catalytic
S359_035
converter Z29

External exhaust gas return not needed

The external exhaust gas return has been omitted on The mapped range with external exhaust gas return
the TSI engines. Due to the charging components, the would be very small and the fuel savings in the overall
proportion in which the engine works as a purely consumption due to the dethrottling of the further
naturally aspirated engine is low. This is, however, opened throttle valve would be small.
necessary to draw the exhaust gases.

27
 Engine management

System overview
Sensors

Intake manifold pressure sender G71 with intake air

temperature sender G42
Intake manifold pressure sender (supercharger)G583
with intake air temperature sender G520
Charge air pressure sender (turbocharger) G31 with
intake air temperature sender G299

Engine speed sender G28

Hall sender G40

Throttle valve module J338

Diagnostic
Angle sender for throttle valve drive G187, G188
connection
Regulating flap control unit J808
Regulating flap potentiometer G584

Accelerator position sender G79 and G185

Clutch position sender G476

Brake pedal position sender G100

Communications line
Fuel pressure sender G247

CAN drive
Knock sensor G61

Coolant temperature sender G62

Radiator outlet coolant temperature sender G83

Intake manifold flap potentiometer G336

Lambda probe G39

Onboard
supply control unit J519
Lambda probe after catalytic converterG130 Data bus diagnostic
interface J533
Brake servo pressure sensor G294

Sensor for current measurement G582

Winter driving program button E598*

Additional input signals

* Only used in 1.4l/125kW TSI engine

28
 Control elements

Fuel pump control unit J538

Engine control unit J623 Fuel pump G6
with sender for
ambient pressure Injectors for cylinders 1 - 4 N30-33

Ignition coil 1 - 4 with output stage

N70, N127, N291, N292

Throttle valve module J338

Throttle valve drive G186

Regulating flap control unit J808

Regulating flap position control motor V380

Motronic current supply relay J271

Fuel pressure regulating valve N276

Active charcoal filter system solenoid valve N80

Intake manifold flap air flow control valve N316

Control unit with
display in dash panel Magnetic clutch for supercharger N421
insert J285

Lambda probe heater Z19

Lambda probe heater after catalytic converter Z29

Inlet camshaft timing adjustment valve N205

Charge air pressure gauge

Exhaust emissions warning

Electronic power control

Turbocharger air recirculation valve N249

fault lamp K132

Charge pressure control solenoid valve N75

lamp K83

Additional coolant pump relay J496

Coolant circulation pump V50
G30

Additional output signals

S359_036

29
 Engine Management

CAN networking
The diagram below shows the control units with which the engine control unit J623 communicates via the CAN
data bus and exchanges data.
For example, the control unit in dash panel insert J285 receives the current boost pressure from the engine control
unit J623 via the CAN data bus. The information is used to display the boost pressure.

G419

J623 J431 J104 J743*

T16

J500 J587*

Drive CAN data

G85 bus
J234
J334 Convenience CAN
J285 data bus
E221
J533 LIN data bus

J527
J255

J519 S359_083

E221 Operating unit in steering wheel J500 Power steering control unit
(multifunction steering wheel) J519 Onboard supply control unit
G85 Steering angle sender J527 Steering column electronics control unit
G419 ESP sensor unit J533 Data bus diagnostic interface
J104 ABS control unit J587* Selector lever sensors control unit
J234 Airbag control unit J623 Engine control unit
J255 Climatronic control unit J743* Mechatronic unit for direct shift gearbox
J285 Control unit with display in dash panel insert T16 Diagnosis connector
J334 Immobilizer control unit
J431 Control unit for headlight range control * only with direct shift gearbox

30
Engine control unit J623
The engine control unit is installed in the centre of the
plenum chamber. The engine management system is
the
Bosch Motronic MED 9.5.10.
The additional functions compared with the
1.6l/85kW FSI engine include the boost pressure
regulation, a winter driving program, the circulating
pump control and the starter Lambda probe control.
The operating modes are homogeneous mode and
the double-injection catalytic converter heating mode.

Engine control unit J623 S359_038

Exhaust gas-related faults are indicated by To protect the clutch, the engine speed is
the exhaust emissions warning lamp K83 limited to approx. 4,000 rpm when
and functional errors in the system by the the car is stationary.
electronic power control fault lamp K132.

Boost pressure regulation

One new function in the engine management system
is boost pressure regulation. 2.4

The diagram shows the boost pressure of the charging 2.0

Pressure ratio [bar]

components at full load.

1.8
As the speed increases, the boost pressure of the
1.6
turbocharger and the supercharger can be reduced.
As a result, less drive power is required from the 1.4

engine. 1.2
Furthermore the supercharger supplies a large
amount of air at low revs. Subsequently a high flow of 2000 3000 4000 5000 6000

exhaust gases is available that is supplied to the Engine speed [rpm]

S359_109
turbocharger turbine. It can therefore generate the Compressor boost pressure
necessary boost pressure in the low rev ranges unlike
pure turbocharged engines. The turbocharger is in Turbocharger boost pressure
principle “pushed” by the supercharger.
Boost pressure of the turbocharger and
supercharger together
Boost pressure of turbocharger in engine with
simple turbocharging

31
 Engine Management

Sensors
Intake manifold pressure sender G71 with intake air temperature sender G42

This combined sender is screwed into the plastic

intake manifold. It measures the pressure and the
temperature in the intake manifold.

Signal use

The engine control unit calculates the air mass drawn

in from the signals and engine speed.

Effects of signal failure

If the signal fails, the throttle valve position and the

Intake manifold pressure sender G71 S359_047
temperature of the intake air temperature sender with intake air temperature sender
G299 is used as a replacement signal. G42
The turbocharger is only operated with regulation. If
other sensors fail, the supercharger can be switched
off.

Intake manifold pressure sender (supercharger)

G583 with intake air temperature sender G520

This combined sender is screwed to the intake

manifold behind the supercharger or behind the
regulating flap control unit. It measures the pressure
and temperature of the intake air in this area.

Signal use

Using the signals, the supercharger boost pressure is

regulated via the regulating flap control unit. At the
same time, the signal of the intake air temperature
sender is used to protect components against high
temperatures. Above a temperature of 130°C, the Intake manifold pressure sender G583 with S359_049
supercharger power is throttled. intake air temperature sender G520

Effects of signal failure

If the combined sender fails, regulation of the turbocharger is only operated with regulation. The
supercharger boost pressure is no longer possible. engine power is reduced in the lower rev ranges.
Supercharger operation is no longer allowed and the

32
Charge air pressure sender G31 with intake air temperature sender 2 G299
This combined sender is screwed into the intake
manifold just in front of the throttle valve module. It
measures the pressure and temperature in this area.

Signal use

The signal from the charge air pressure sender is used

by the engine control unit to control the boost
pressure of the turbocharger via the charge pressure
control solenoid valve.
The signal from the intake air temperature sender is
Charge air pressure sender G31 with S359_062
used to calculate a correction value for the boost intake air temperature sender 2 G299
pressure. The temperature influence on the density of
the charge air is taken into consideration. Effects of signal failure

If the sender fails, the turbocharger is only operated

with regulation. If other sensors fail, the supercharger
can also be switched off.

Ambient pressure sender

The sender is installed in the engine control unit and Engine control unit with
measures the ambient pressure. ambient pressure sender

Signal use

The ambient air pressure is required as a correction

value for boost pressure regulation as the density of
the air falls as the altitude rises.

Effects of signal failure

S359_039
If the sender for ambient pressure fails, the
turbocharger is only operated with regulation. Higher
emissions values and a loss in power can occur here.

33
 Engine Management

Engine speed sender G28

The engine speed sender is mounted on the cylinder
block. It scans a sender wheel in the crankshaft
sealing flange. Using these signals, the engine control
unit calculates the engine speed and the position of
the crankshaft in relation to the camshaft using the
Hall sender G40.

Signal use

The calculated injection time, the injection duration

and the ignition timing are determined with the signal.
It is also used to adjust the camshaft.
Engine speed sender G28 S359_089

Effects of signal failure

If the sender fails, the engine will no longer run and

can also not be started.

Hall sender G40

The Hall sender is on the flywheel side of the camshaft

case above the inlet camshaft. It scans four teeth cast
on the inlet camshaft.

Signal use

Together with the engine speed sender, it is used to

recognise the ignition TDC of the first cylinder and the
position of the inlet camshaft. The signals are used to
determine the injection time, the ignition time and for
adjusting the camshaft.
Hall sender G40 S359_057

Effects of signal failure

The engine continues to run if the sender fails. camshaft is held in the “late position”. A loss in torque
However, it cannot be started again. The camshaft results.
adjustment is switched off and the inlet

34
Throttle valve module J338 with
angle sender for throttle valve drive G187 and G188
The throttle valve module with the angle sender for
throttle valve drive is in the intake duct in front of the
intake manifold.

Signal use

Using the signals from the angle sender, the engine

control unit recognises the position of the throttle
valve and can control it accordingly. For safety
reasons, there are two senders whose values are
compared with each other.

Throttle valve module J338 with S359_050

angle sender for throttle
Effects of signal failure valve drive G187 and G188

If a sender fails, system components like the cruise switched off and the engine speed limited to
control system will be switched off. 1,500 rpm.
If both senders fail, the throttle valve drive will be

Regulating flap control unit J808

Regulating flap potentiometer G584
The regulating flap potentiometer is in the regulating
flap control unit. The regulating flap control unit is
installed in the intake duct after the air filter.

Signal use

The engine control unit recognises the position of the

regulating flap potentiometer. The engine control unit
can then position the regulating flap in any position
required.
S359_052
Regulating flap control unit J808 with
regulating flap potentiometer G584

Effects of signal failure

If the signal fails, the regulating flap remains

constantly open and the supercharger is no longer
activated.

35
 Engine Management

Accelerator position sender G79 and G185

The two accelerator position senders are part of the Metal plate
accelerator module and work as contact-free as
inductive pickups. The accelerator position is
recognised using the signals from the accelerator Accelerator pedal
position sender.

Signal use

The engine control unit uses the signals to calculate

the torque required by the driver. For safety reasons,
S359_082
there are two senders whose values are compared
with each other as with the throttle valve module.
Accelerator position sender
G79 and G185

Effects of signal failure

If one or both senders fail, the convenience functions

(e.g. cruise control, engine braking control) will be
switched off.

Failure of one sender Failure of both senders

If one sender fails, the system initially switches to idle. If both senders fail, the engine will only run with an
If the second sender is recognised in the idle position increased idle speed (maximum 1,500 rpm) and will
within a certain test time, driving will be possible no longer respond to the accelerator pedal.
again.
At the required full load, the engine speed is only
increased slowly.

36
Clutch position sender G476
The clutch position sender is clipped to the sender
cylinder. It indicates that the clutch pedal has been
pressed.

Signal use

When clutch is pressed ...

- the cruise control is switched off.

- the injection quantity is reduced briefly so that
engine judder is prevented when you change
gear.
- the supercharger magnetic clutch can be activated
when the car is stationary. This ensures that the
boost pressure is reached very quickly when the car
pulls away.
Clutch pedal with S359_084
clutch position sender

Design
Clutch Mounting Push rod
sender cylinder
The sender cylinder is fastened to the mounting using
a bayonet connection.
When the clutch pedal is pressed, the push rod
pushes the piston in the sender cylinder.

Effects of signal failure

If the clutch position sender fails, the cruise control

system will not work and there could be engine judder
when you change gear. Clutch
position sender

Piston with Pedal travel

permanent magnet
S359_085

37
 Engine Management

Brake pedal position sender G100

The brake pedal position sender is screwed to the
main brake cylinder. It recognises whether the brake
pedal is being pressed.

Signal use

The brake lights are operated via the onboard supply

control unit.
S359_067
Furthermore the engine control unit prevents the car
accelerating if the brake and accelerator pedals are
pressed at the same time. The injection quantity is Brake pedal position sender G100
reduced or the ignition time and the throttle valve are
adjusted. Effects of signal failure

If the signal of one of the two senders fails, the

injection quantity is reduced and the engine has less
power.
Furthermore the control cruise is switched off.

Electrical circuit:

- The voltage for the brake pedal position sender

G100 is supplied via the voltage supply relay, J519
J681
terminal 15 J681.
- The earth connection is via the body earth point.
- The two signal lines go to the engine control unit
J623. The signal also goes to the onboard supply S S S
control unit J519 from one cable. This operates the
G100
brake lights. A

J623

Voltage supply S359_096

Earth connection
Input signal

A Battery
S Fuse

38
How it works:

When the brake pedal is pressed, the pressure rod in the brake master cylinder moves the piston with magnetic
ring (permanent magnet). Two Hall senders have been fitted in the brake pedal position sender for safety reasons.

In the following explanation, only Hall sender 1 with its signal patterns is described for reasons of simplification. The
signals from sender 2 are in the opposite direction.

Piston with magnetic

Brake pedal not pressed:
ring in front of Hall
senders
When the brake pedal is not pressed, the piston with
the magnet ring is in the rest position.
The evaluation electronics of the brake pedal position
sender issue a signal voltage of 0 - 2 Volt to the
engine control unit and the onboard supply control
unit.
This indicates that the brake pedal has not been
pressed. Brake pedal Evaluation
position sender electronics
Hall sender 1 Hall sender 2

S359_068

Piston with magnetic

Brake pedal pressed: ring over the Hall
senders
When the brake pedal is pressed, the piston is pushed
over the Hall sender.
When the magnetic ring of the piston crosses the
switching point of the Hall sender, the evaluation
electronics issues a signal voltage, which is up to
2 volt below the onboard supply voltage, to the
engine control unit.
This indicates that the brake pedal has been pressed. Hall sender
Hall sender 1 Hall sender 2
signal increases signal decreases
S359_069

39
 Engine Management

Fuel pressure sender G247

The sender is on the lower part of the intake manifold
on the flywheel side and is screwed into the plastic
fuel distribution pipe.
It measures the fuel pressure in the high-pressure fuel
system and sends the signal to the engine control unit.

Signal use

The engine control unit evaluates the signals and

regulates the pressure in the fuel distribution pipe
using the fuel pressure regulating valve.
Fuel pressure sender G247 S359_090

Effects of signal failure

If the fuel pressure sender fails, the fuel pressure the existing fuel pressure. This reduces the engine
regulating valve is switched off, the electrical fuel torque drastically.
pump is triggered fully and the engine is run with

Knock sensor G61

The knock sensor is screwed to the cylinder block
below the supercharger. The signals from the knock
sensor are used to detect knocking combustion in
specific cylinders.

Signal use

When engine knock is recognised in the

corresponding cylinder, the ignition angle is adjusted
until there is no more knocking.

Knock sensor G61 S359_080

Effects of signal failure

If the knock sensor fails, the ignition angle of all This leads to an increase in fuel consumption and the
cylinders is set to a fixed value in the “late” direction. power and torque fall.

40
Coolant temperature sender G62
The coolant temperature sender is on the coolant
distributor. It measures the coolant temperature and
forwards it to the engine control unit.

Signal use

The coolant temperature is used to calculate the

injection quantity, the injection timing and to control
the handling functions.

Coolant temperature sender G62 S359_091

Effects of signal failure

If the signal fails, a temperature is calculated by the

engine control unit according to the engine map and
used for the individual functions.

Radiator outlet coolant temperature sender G83

The coolant temperature sender G83 is in the hose on
the radiator outlet and measures the temperature of
the coolant leaving the radiator there.

Signal use

The radiator fan is controlled by comparing both

signals from the coolant temperature sender G62 and
coolant temperature sender G83.

Radiator outlet coolant S359_088

temperature sender G83
Effects of signal failure

If the signal from the coolant temperature sender G83

fails, the temperature from the coolant temperature
sender G62 is used as a substitute value.

41
 Engine Management

Lambda probe G39 with Lambda probe G39 with

Lambda probe heating Z19
Lambda probe heating Z19
A step-type Lambda probe is used in front of the
catalytic converter. This is possible because you can
drive with Lambda 1 in almost all engine modes. It is
screwed into the exhaust pipe in front of the catalytic
converter close to the engine. It is used to determine
the residual oxygen content in the exhaust in front of
the catalytic converter.
The Lambda probe heating ensures that the Lambda
probe reaches its operating temperature very quickly.

S359_063
Signal use Effects of signal failure

Using the signal voltage, the engine control unit If the signal fails, there will be no Lambda control, but
recognises whether the engine is running with a rich pre-control of the injection quantity, the Lambda
or lean air/fuel mixture. adjustment will be blocked and the activated charcoal
filter system will switch to emergency mode.

Lambda probe after catalytic converter G130

with Lambda probe heating Z29
This Lambda probe is also a step-type Lambda
probe.
The Lambda probe heating ensures that the Lambda
probe reaches its operating temperature very quickly.

Signal use

The Lambda probe after the catalytic converter is

used to check the catalytic converter function.

Lambda probe G130 with S359_064

Lambda probe heating Z29
Effects of signal failure

If the signal fails, the catalytic converter function will

no longer be monitored.

42
Intake manifold flap potentiometer G336
It is mounted on the lower part of the intake manifold Intake manifold flap potentiometer G336
and is connected to the shaft for the intake manifold
flaps. It recognises the position of the intake manifold
flaps.
Signal use

The position is important because the intake manifold

flap control has an effect on the air flow in the
combustion chamber and the supplied air mass. The
position of the intake manifold is therefore related to
the exhaust gas and needs to be checked by the self-
diagnosis system.

Effects of signal failure S359_061

If the signal from the potentiometer fails, the system the corresponding ignition angle is set. There is a loss
can no longer recognise whether the intake manifold in power and torque and the fuel consumption also
flaps are open or closed. A middle setting of the rises.
intake manifold flap is used as a substitute value and

Brake servo pressure sensor G294

It is located in the hose between the intake manifold Brake servo
and the brake servo and measures the pressure in the pressure sensor G294
brake servo.

Signal use

Using the voltage signal from the pressure sensor, the

engine control unit recognises whether the vacuum is
sufficient for the brake servo to work. If the vacuum
pressure is too low, the air-conditioning system will be
switched off. This closes the throttle valve slightly and
the vacuum pressure rises again.

S359_099

Effects of signal failure

If the signal fails, the system switches to a map-related

pressure value with which the corresponding function
is calculated.

43
 Engine Management

Sensor for current measurement G582

Sensor for current measurement G582
The sensor for current measurement is located on the
left of the engine compartment in the E-box. It
recognises the current path upon activation of the
supercharger magnetic clutch.

Signal use

Using the power consumption, the engine control unit

regulates the PWM signal, with which the magnetic
clutch is operated and closes it gently.

S359_070
Effects of signal failure

If the signal fails, the current path is no longer If the sensor for current measurement fails completely,
recognised and the magnetic clutch is engaged with the supercharger can no longer be activated.
more of a jolt.

Electrical circuit J271

- The voltage for the magnetic clutch for

supercharger N421 is supplied via the current
supply relay J271 and the sensor for current
measurement G582.

- The magnetic clutch is controlled by the engine G582 N421

control unit J623 via the ground connection with a
PWM signal.
J623
- In the sensor, a voltage measurement on a low-
S359_058
ohm resistor is used to determine the current path,
which is then sent to the engine control unit. The Voltage supply
magnet clutch is operated depending on the signal. Input signal
Output signal
- If the magnetic clutch is no longer triggered, the
magnetic field in the coil will collapse and a high
induction voltage results. To protect the engine
control unit against damage, this induction voltage
is sent to the sensor for current measurement. The
sensor contains a diode that conducts when a
specific voltage difference between both sides is
reached. This reduces the voltage peaks.

44
Winter driving program button E598
The winter driving program button is clipped into the
centre console in front of the gearstick. The winter
driving program is intended for driving on slippery
surfaces.
It is only used with the 1.4l/125kW TSI engine.

The winter driving program remains active

until the button is pressed again or the
ignition has been switched off for longer
than 5 seconds. This ensures that the winter
driving program is also active if the engine S359_073
is stalled and is started again straightaway.

S359_074

Winter driving program button E598

Signal use Effects of signal failure

When pressed, a comfort-oriented engine map and a If the button fails, only the normal driving program
flatter accelerator characteristic curve is activated. will be available.
This limits the torque provided according to the gear
and engine speed. It is therefore easier to pull away
on slippery surfaces (wet, ice, snow, mud etc.).
On cars with direct shift gearbox, the winter driving
program can be activated in the D and R positions.

45
 Engine Management

Actuators
Motronic current supply relay J271
The Motronic current supply relay is located on the
left of the engine compartment in the E-box.

Task

Using the current supply relay, certain functions can

also be used and work in run-on mode after the
engine has been turned off (ignition OFF).
In this operating mode, the pressure senders are
compared and the ignition coils or radiator fan are
operated.

Motronic current supply S359_071

relay J271

Effects upon failure

If the relay fails, the corresponding sensors and is turned off and can also no longer be started.
actuators are no longer triggered. The engine

Ignition coils 1 - 4 with

output stage N70, N127, N291, N292
The ignition coils with output stages are located in the
centre of the cylinder head.

Task

The ignition coils with output stages have the task of

igniting the fuel-air mixture at the right time.
The ignition angle is controlled individually for each
cylinder.

Ignition coils output stages S359_054

N70, N127, N291, N292
Effects upon failure

If an ignition coil fails, the injection for the

corresponding cylinder will be deactivated. This is
possible with a maximum of one cylinder.

46
Throttle valve module J338 with
throttle valve drive G186
The throttle valve module with the throttle valve drive
is in the intake duct in front of the intake manifold.

Task

The throttle valve drive is an electric motor that is

operated by the engine control unit. It operates the
throttle valve via a small gear mechanism. The
adjustment range is continuous from the idle to the full
load setting.

Throttle valve module J338 with S359_108

throttle valve drive G186
Effects upon failure

If the throttle valve drive fails, the throttle valve will convenience functions (e.g. cruise control) are
move to the emergency mode position. Only the switched off.
emergency mode properties are available and the

Regulating flap control unit J808 with

regulating flap position control motor V380
The regulating flap control unit with the regulating
flap position control motor is located in the intake duct
behind the air filter.

Task

The control motor is controlled by the engine control

unit and operates the control flap continuously.
Depending on the regulating flap position more or
less compressed air flows back to the mechanical
supercharger. This regulates the boost pressure after
the supercharger.

Regulating flap control unit J808 with S359_107

regulating flap position control motor
Effects upon failure V380

If the control motor fails, the regulating flap will move No more boost pressure is built up by the
to the emergency mode position (fully open). At the supercharger.
same time, the supercharger may not be activated.

47
 Engine Management

Intake manifold flap air flow control valve N316

The valve is screwed onto the intake duct behind the
regulating valve control unit.

Task

It is controlled by the engine control unit and opens

the path from the vacuum reservoir to the vacuum
control element. The intake manifold flaps are then
operated by the vacuum control element.

Intake manifold flap air flow control valve S359_051

N316
Effects upon failure

If the valve fails, it will not be possible to adjust the to the open position. This worsens the combustion.
intake manifold flaps and the flaps will be moved

Inlet camshaft timing adjustment valve N205

This valve is in the camshaft housing and is
incorporated in the engine oil circuit.

Task

Triggering the valve for the inlet camshaft control

valve distributes the oil in the vane adjuster.
Depending on which oil channel is opened, the inner
rotor is adjusted in the “early” or “late” direction or
kept in its position. As the inner rotor is screwed to the
inlet camshaft, it is also adjusted in the same way.

Inlet camshaft timing adjustment valve N205 S359_059

Effects upon failure

If the valve for camshaft adjustment fails, camshaft the inlet camshaft is held in the “late” position. A loss
adjustment will no longer be possible and in torque results.

48
Charge pressure control solenoid valve N75
The electro-pneumatic charge pressure control valve
is screwed to the return valve for the crankcase
breather.

Task

The solenoid valve is clocked by the engine control

unit and switches the control pressure in the pressure
cell for the turbocharger. This operates the waste gate
flap and diverts part of the exhaust gases past the
turbine to the exhaust system. This regulates the
turbine power and the boost pressure.
Charge pressure S359_055
control solenoid valve N75

Effects upon failure

If the valve fails, boost pressure is applied to the

pressure cell. The boost pressure is thus lower and the
engine power is reduced.

Turbocharger air recirculation valve N249

The electrical turbocharger air recirculation valve is
screwed to the turbocharger housing.

Task

The recirculation valve for turbocharger prevents

noises upon switchover to boost mode and damage to
the compressor wheel of the turbocharger.
Upon switchover to boost mode, the compressor
wheel is still rotating at speed and compressing the
air. The compressed air is pumped to the closed
throttle flap and reflected by it. It flows back to the
Turbocharger air recirculation valve N249 S359_056
turbocharger and meets the compressor wheel. Noise
can result.
To avoid this, the circulation valve is opened and the Effects upon failure
turbine and compressor sides of the turbocharger are
connected. The boost pressure is suddenly reduced If the circulation valve is leaking, the boost pressure is
and backflow is prevented. Furthermore a back reduced and therefore also the engine output.
pressure in the compressor housing is prevented and If the valve can no longer be operated, there will be
the turbocharger speed is not braked so greatly. noise from the turbocharger in boost mode.

49
 Engine Management

Magnetic clutch for supercharger N421

Magnetic clutch for supercharger N421
The maintenance-free magnetic clutch for the
supercharger is part of the coolant pump module. It is
used to activate the supercharger whenever
necessary.
Task

The magnetic clutch is engaged by the engine control

unit when necessary. The magnetic clutch then closes
and forms a positive connection between the coolant
pump pulley and the magnetic clutch pulley for the
supercharger. The supercharger is then driven by the
supercharger belt drive.

Coolant pump module S359_060

On cars with manual gearboxes, the

magnetic clutch is operated with the Effects upon failure
onboard supply voltage up to an engine
speed of 1,000 rpm and above that with a If the magnetic clutch fails, the supercharger can no
PWM signal. longer be operated.
On cars with the direct shift gearbox, the
magnetic clutch is always controlled with a
PWM signal.
If the magnetic clutch is closed, it is Clutch lining
controlled with the onboard supply voltage.
Solenoid Friction plate

Design

The magnetic clutch consists of …

Coolant pump
- a coolant pump pulley with a spring-loaded friction impeller
plate. It is screwed to the coolant pump drive shaft.
- a magnetic clutch pulley mounted on bearings for
the supercharger with a clutch lining.
It is mounted in a two-row deep-groove ball
bearing on the coolant pump housing so it rotates.
- The solenoid is permanently mounted to the
coolant pump housing.

S359_098
Pulley for magnetic Coolant pump
clutch for pulley
supercharger

50
How it works:

Magnetic clutch not engaged Clutch lining

Pulley for magnetic Friction plate

The coolant pump pulley is driven by the crankshaft clutch for supercharger
via the ancillary components drive belt.
As the magnetic clutch is not engaged, the A
compressor belt pulley does not turn. The
supercharger is not driven. Gap “A” is between the
clutch lining and friction plate.

Coolant pump S359_041

pulley

Magnetic clutch engaged Clutch lining

Pulley for magnetic Friction plate

When the supercharger should be activated, a clutch for
voltage is applied to the solenoid. A magnetic field is supercharger
formed. This pulls the friction plate against the clutch
lining and forms a positive connection between the
supercharger magnetic clutch pulley and the coolant
pump pulley.
The mechanical supercharger is driven.
It runs until the power circuit for the solenoid is
interrupted.
The friction plate is then returned by springs on the
coolant pump pulley.
The supercharger pulley then no longer rotates.

S359_042
Solenoid Magnet flux

51
 Engine Management

Fuel pump control unit J538

The control unit is mounted under the rear bench in
the cover for the electrical fuel pump.

Task

The fuel pump control unit receives a signal from the

engine control unit and controls the electrical fuel
pump with a PWM signal (pulse-width modulation). It
regulates the pressure in the low-pressure fuel system
between 0.5 and 5 bar.
The pressure is raised to up to 6.5 bar for warm and
Fuel pump control unit J538 S359_075
cold starts.

Effects of signal failure

If the fuel pump control unit fails, the engine will not
run.

Fuel pump G6
The electrical fuel pump and the fuel filter are
combined in the fuel supply unit.
The fuel supply unit is in the fuel tank.

Task

The electrical fuel pump delivers the fuel in the low-

pressure fuel system to the high-pressure fuel pump. It
Fuel pump G6 S359_076
is controlled with a PWM signal from the fuel pump
control unit.
The electrical fuel pump supplies as much fuel as the Effects upon failure
engine requires.
If the electrical fuel pump fails, the engine will not run.

52
High-pressure injectors N30 - N33
The high-pressure injectors are fitted in the cylinder
head. They inject the fuel into the cylinders at high
pressure.

Task

The injectors need to precisely inject and atomise the

fuel in a very short time.
In the double injection catalytic converter heating
mode, fuel is therefore injected twice. The first time
during the intake stroke and the second time approx.
Injectors N30 - N33 S359_079
50° KW before ignition TDC to warm up the catalytic
converter quickly.
In homogeneous mode, the fuel is injected during the
intake stroke and is distributed evenly around the
whole combustion chamber.

Multi-port injector

The high-pressure injector has 6 fuel outlet bores. The

High-pressure
individual jets are arranged so that the combustion injector
chamber parts do not become wet and air-fuel
mixture is distributed evenly.
The maximum injection pressure is 150 bar to ensure
very good preparation and atomising of the fuel.
S359_105
Even at full load, this ensures that enough fuel is
injected.
6 individual jets

Effects upon failure

A faulty injector is detected by the fault recognition

system and is no longer controlled.

53
 Engine Management

Fuel pressure regulating valve N276

The fuel pressure regulating valve is located on
the side of the high-pressure fuel pump.

Task

It has the task of supplying the required quantity of

fuel at the required fuel pressure in the fuel rail.

Fuel pressure High-pressure S359_053

Effects upon failure regulating valve N276 fuel pump

The regulating valve is open and not powered. This electrical fuel pump. This reduces the engine torque
means that high pressure is not built up and the drastically.
engine is run with the existing fuel pressure from the

Active charcoal filter system solenoid valve N80

The solenoid valve for the active charcoal filter system To Active charcoal filter system
turbocharger solenoid valve N80
is mounted near to the throttle valve module.

Task

The valve is operated at a certain frequency and

ventilates the activated charcoal canister. The fuel
vapours are delivered to the intake duct behind the
throttle valve module or in front of the turbocharger
depending on the pressure conditions. A specific
pressure drop is required to draw the fuel vapours
from the activated charcoal canister. The check valve
ensures that no air is pushed in the direction of the
Check valve To intake manifold From active charcoal
activated charcoal canister. filter system
S359_048

Effects of signal failure

If the power supply is interrupted, the valve remains The tank is not ventilated and there may be a smell of
closed. fuel.

54
Additional coolant pump relay J496
The additional coolant pump relay is on the left under
the dash panel.

Task

The high working currents for the coolant circulation

pump V50 are switched by the relay.

Effects upon failure

If the relay fails, continued coolant circulation will not

Additional coolant pump relay J496 S359_034
be possible and there could be overheating.

Coolant circulation pump V50

The coolant circulation pump is on the left-hand side
of the engine compartment near the three-way
catalytic converter. It is connected to the coolant
return from the coolant distributor housing to the
radiator.

Task

After the engine has been turned off, overheating can

occur (steam bubbles) near the turbocharger as the
coolant is still being heated.
To avoid this, the coolant recirculation pump is
Coolant circulation pump V50 S359_095
activated by the engine control unit for a maximum of
15 minutes.
The switch-on conditions for the coolant circulation Effects upon failure
pump result from the following signals:
If the coolant circulation pump fails, continued
- Coolant temperature sender (G62) coolant circulation will no longer be possible and
- Oil level and oil temperature sender (G266) there could be overheating. A faulty pump will not be
recognised by the self-diagnosis system.

55
 Engine Management

Charge air pressure gauge G30

The boost gauge is located in the dash panel insert
underneath the multi-function display.
The signal comes from the engine control unit to the
dash panel insert via the CAN data bus.
There is no coolant temperature gauge. Warnings will
appear in the multi-function display as before.

Task

When boost pressure is required, the boost gauge

Charge air pressure gauge G30 S359_077
shows the relationship between the actual and
maximum boost pressure at the current engine speed.
This type of display should counteract a possible
problem of “boost pressure falling as rpm rises”. The
maximum boost pressure at full load and an engine
speed of 1,500 rpm is around 2.5 bar (absolute) and
at full load and an engine speed of 5,500 rpm
1.8 bar (absolute).

Effects upon failure

If the gauge fails, the boost pressure will no longer be

indicated. Failure has no effect on the system.

56
Boost gauge

Here is an example to explain the gauge.

The supercharging components can produce a maximum boost pressure of 2.5 bar (absolute) at an engine speed
of 1,500 rpm and full load.

Needle position with medium charging

The needle is in the middle.

This means that the engine is running at partial load
and the supercharging components have produced
medium boost pressure at the engine speed of
1,500 rpm.

S359_078

Needle position with maximum charging

The needle is at the end of the gauge.

This means that the supercharging components have
produced the maximum possible boost pressure at an
engine speed of 1,500 rpm.

S359_106

57
 Engine Management

Functional diagram

J681

S S S S S

A S S
S
G G6
E598 K243 L156 N421 V50 G100

J538

J496
G582

N249
N75
31 31
J285 G1
J285

J338

N30 N31 N32 N33 G294 G83 G71 G42 G247 G40
G186 G187 G188 G79 G185

31
S359_043
A Battery G294 Brake servo pressure sensor
E598 Winter driving program button G582 Sensor for current measurement
G Fuel gauge sender J285 Control unit with display in dash panel insert
G1 Fuel gauge J338 Throttle valve module
G6 Fuel pump J496 Additional coolant pump relay
G40 Hall sender J538 Fuel pump control unit
G42 Intake air temperature sender J681 Terminal 15 voltage supply relay
G71 Intake manifold pressure sender K243 Winter program warning lamp
G79 Accelerator position sender L156 Switch illumination bulb
G83 Radiator outlet coolant N30- Injectors for cylinders 1 - 4
temperature sender N33
G100 Brake pedal position sender N75 Charge pressure control solenoid valve
G185 Accelerator position sender 2 N249 Turbocharger air recirculation valve
G186 Throttle valve drive N421 Magnetic clutch for supercharger
G187 Throttle valve drive angle sender S Fuse
G188 Throttle valve drive angle sender V50 Coolant circulation pump
G247 Fuel pressure sender

58
 J519

S S S S S S

A
G476 G39 Z19 G130 Z29 J271 J533

N80 N205 N276 N316

1 2 3

J623

J808 N70 N127 N291 N292

0
G336

G584

V380 G583 G31 G28 G61 G62

P P P P
G520 G299 Q Q Q Q

G28 Engine speed sender N205 Inlet camshaft timing adjustment valve
G31 Charge air pressure sender (turbocharger) N276 Fuel pressure regulating valve
G39 Lambda probe N291 Ignition coil 3 with output stage
G61 Knock sensor N292 Ignition coil 4 with output stage
G62 Coolant temperature sender N316 Intake manifold flap air flow control valve
G130 Lambda probe after catalytic converter P Spark plug connector
G299 Intake air temperature sender Q Spark plugs
G336 Intake manifold flap potentiometer V380 Regulating flap position control motor
G476 Clutch position sender Z19 Lambda probe heater
G520 Intake air temperature sender Z29 Lambda probe heater
G583 Intake manifold pressure sender 1 Cruise control system switch
G584 Regulating flap potentiometer 2 Alternator terminal DFM
J271 Motronic current supply relay 3 Radiator fan level 1
J519 Onboard supply control unit Output signal
J533 Data bus diagnostic interface Input signal
J623 Engine control unit Positive
J808 Regulating flap control unit Earth
N70 Ignition coil 1 with output stage Bi-directional cable
N80 Active charcoal filter system solenoid valve CAN data bus
N127 Ignition coil 2 with output stage

59
 Service

Special tools

Name Tool Application

Locking pin –T10340- The locking bolt locks the crankshaft in the
engine rotation direction.

Please note the repair

instructions in ELSA when
fitting the crankshaft pulley.
S359_045

Guide pins –T10341- The two guide pins hold the supercharger
in the correct position during installation.

S359_044

Engine support –T40075- The engine support allows you to lower

with adapters -/4, -/5, -/6 the engine together with the gearbox.

S359_087

Compressor belt pulley mounting bolt

You need to hold the supercharger shaft with a
spanner when loosening and tightening the
supercharger pulley bolt.

Please note the further information in the

repair guide.

S359_018

60
Inspection window for seals
Inspection windows are provided for some parts Please note that you cannot see whether
of the intake system. You can use these windows the seal is fitted properly.
to check whether the seals are fitted without removing
the parts.

Supercharger Inspection window for

seal between intake manifold
and lower part of intake manifold

S359_100 S359_101
Inspection flap for seal between Regulating flap Inspection window for seal
soundproofing and control unit between intake manifold and
supercharger regulating flap control unit

S359_102 S359_103
Sender for Inspection window for Inspection window for
fuel pressure seal between intake manifold seal between intake manifold
and lower part of intake manifold and intake manifold flange

61
 Test Yourself

Which answers are correct?

One or several of the answers could be correct.

1. What is meant by “downsizing”?

a) Downsizing means the output of an engine with large displacement is decreased thus reducing the fuel
consumption.

b) Downsizing involves reducing the displacement of an engine while keeping the same output, for example.
This reduces the internal friction and cuts fuel consumption.

c) Downsizing involves increasing the displacement, raising the torque and saving fuel.

2. How many poly-V-belts does the TSI engine have?

a) It has just one poly-V-belt for driving the ancillary components.

b) It has two poly-V-belts. One to drive the ancillary components and one to drive the supercharger.

c) It has three poly-V-belts to drive the ancillary components, the supercharger and the oil pump.

3. Above which engine speed is the supercharger no longer activated?

a) 1,500 rpm

b) 2,200 rpm

c) 3,500 rpm

4. The signal from the sensor for current measurement G 582 can be used ....

a) ... to regulate the clocking of the magnetic clutch.

b) ... to regulate the mixture composition.

c) ... to control the regulating flap.

62
5. Which statements about the supercharger magnetic clutch are correct?

a) The magnetic clutch is part of the coolant pump module.

b) The mechanical supercharger is activated using the magnetic clutch as required.

c) The magnetic clutch is maintenance-free.

6. When do the two supercharging components produce boost pressure?

a) The turbocharger produces the boost pressure immediately if the exhaust gas energy is sufficient.

b) The supercharger is only activated when the boost pressure produced by the turbocharger is not sufficient.

c) Both charging components are always activated and produce boost pressure.

7. How is the boost pressure of the charging components regulated?

a) The turbocharger boost pressure is controlled by the charge pressure control solenoid valve.

b) The boost pressure of the supercharging components is controlled via the throttle valve module.

c) The supercharger boost pressure is controlled via the regulating flap control unit.

8. What kind of Lambda probe is used in the 1.4l TSI engine as a pre-catalytic converter probe?

a) A broadband Lambda probe

b) A step-type Lambda probe 8. b

7. a,c
6. a,b
c) A NOx sender
5. a,b,c
4. a
3. c
2. b
1. b
Answers

63
 359

© VOLKSWAGEN AG, Wolfsburg

All rights and rights to make technical alterations reserved.
000.2811.73.20 Technical status 03/2006

Volkswagen AG
Service Training VSQ-1
Brieffach 1995
38436 Wolfsburg

❀ This paper was manufactured from pulp that was bleached without the use of chlorine.

64