250W High Power Factor Supply For TV: Application Note
250W High Power Factor Supply For TV: Application Note
250W High Power Factor Supply For TV: Application Note
Figure 1.
+135(B+)
+400V
FLY BACK +15
EMI PFC DC-DC CONV
220V FILTER (L4981A) +14
(TEA2261-
TEA5170) -14
+7.5
D95IN236A
AN826/1003 1/6
2/6
10µH COM3
L2
D15 BYT08/200 1
+14V
TR2 OREGA 220pF C32 R49
G5155-01 C38
2200µF 50V 10µF 56K
D9 STTA506M 2
C10 C23
220nF 150µF C33 C39
APPLICATION NOTE
D18 BYT08/400 5
C1 150nF 250V~ 8 2 4 20 3 12 14 +15V
D11 BA157 C35
19 R47
2200µF
1.8K
1,7,10 IC2 C21 25V
100µF
L4981A
TR1 D19 BYW80/200 6
+7.5V
6 11 5 9 17 18 12 C36
R48 R51
C2 220nF 250V~ 2200µF
22K 68K
R14 R7 25V
C16 R18 0.5W
27K 2.7K
C8 39K C19 C9 G5154-02
F1 10µF 1nF 1µF OREGA 7
3AT D7 BA157
1.2nF
3 2 1 T4
C20 47µF BUH515 R44 47K P2
R19 22 C25 1K
R10 R8 C4 C3 2.2nF
12 100K 1nF 470nF
D7 BA157 L1 D7 BA157
COM1 R33 D13 R52
R29 470 BYT11 R40 C37 1K
15 16 11 10 9 14 2.2µH D8 100 3.3K 4.7nF
176-265V~ 9W 1000 COM2
R20 1K B2x85 C3V3
IC1 3 T5 R41 10K 4
R34 BC308 S-BY
TEA2261 C12 R12 C31 470pF
1nF R24
2W 3
1M
T1 SYNC
8 7 6 4,5,12,13 2 1 BC548
1N4148 33K 7 6 5
T2 R55
BC548 2 IC3 R 2
R2 100K R34
C5 R12 C30 TEA5170
1µF 10nF 1µF C42 1
1M 3 1 4 8 150pF
C6 470pF R34 1K TR4
R4 C29
R45 D20
10K C17 220nF
R37 22K 330 1N4148 R54
470pF
R43 6.8K
D5 BA157 240K
R1 1.8K R5 6.8K R38 100
R42 10M
P1 2.2K
C5
10µF C28 4.7nF
D95IN237C
APPLICATION NOTE
3/6
APPLICATION NOTE
SOUND
CON3
+14V
1 OFF
2 10 10
20W 20W ON
-14V
3
+135V
4
SW1
+15V
5
RL 15V RL 135V SBY
+7.5V
6
ON
CON2
3
S-BY
4
D95IN246
On the evaluated board (refer to CON3 in fig.3) As the " stand-by " output values have been set,
the adjusted voltage values are: put the switch in ON position The loads are now
Voltage at out 1 = +16.5V connected and all the circuits of the application
run. The TEA5170 is now supplied and it sends
Voltage at out 3 = -16.5V PWM pulses from the secondary to the primary
Voltage at out 4 = +13.7V side of the converter. T2 is turned on, is T1 is cut-
Voltage at out 1 = +15.7V off, thus enabling the L4981A to start. As the
PFC runs, the voltage at the bulk capacitor C23
Voltage at out 1 = +10V reaches 400V.
TEST RESULTS:
4/6
APPLICATION NOTE
Load Regulation:
Ic
0
0 Vce
Vi IC
TR2 D9
VCE
IL
T3
D95IN292 T4
D95IN259
5/6
APPLICATION NOTE
IL
Ic 0
Vi
Vce 0
0
Vi
IC
TR2 D9
VCE
IL
T3
D95IN292 T4 D95IN259
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is
granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are
subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products
are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
6/6