Chapter 6

Sheet-metal forming
Subjects of interest Introduction/objectives Deformation geometry Forming equipments Shearing and blanking Bending Stretch forming Deep drawing Forming limit criteria Defects in formed parts
Suranaree University of Technology
Tapany Udomphol

Jan-Mar 2007

Objectives

Methods of sheet metal processes such as stretching, shearing, blanking, bending, deep drawing, redrawing are introduced. Variables in sheet forming process will be discussed together with formability and test methods. Defects occurring during the forming process will be emphasised. The solutions to such defect problems will also be given.

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Introduction

Sheet metal forming is a process that materials undergo permanent deformation by cold forming to produce a variety of complex three dimensional shapes. The process is carried out in the plane of sheet by tensile forces with high ratio of surface area to thickness. Friction conditions at the tool-metal interface are very important and controlled by press conditions, lubrication, tool material and surface condition, and strip surface condition. High rate of production and formability is determined by its mechanical properties.

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Classification of sheet metal parts (based on contour)

1) Singly curved parts

(a) Singly curve (b) Stretch flange

2) Contoured flanged parts, i.e., parts with stretch flanges and shrink flanges. 3) Curved sections. 4) Deep-recessed parts, i.e., cups and boxes with either vertical or sloping walls. 5) Shallow-recessed parts, i.e., dishshaped, beaded, embossed and corrugated parts.

(c) Shrink flange

(d) Curved section

(e) Deep drawn cup

(f) Beaded section

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Classification of sheet metal forming (based on operations)

Blanking

Stretching

Deep drawing

Coining

Stamping

Ironing

Folding

Bending

Roll forming of sheet Tapany Udomphol

Wiping down a flange

Suranaree University of Technology

Jan-Mar 2007

Stress state in deformation processes

The geometry of the workpiece can be essentially three dimensional (i.e., rod or bar stock) or two dimensional (i.e., thin sheets). The state of stress is described by three principal stresses, which act along axes perpendicular to principal planes. The principal stresses are by convention called 1, 2 and 3 where 1> 2 > 3

3 2

Principal stresses on an element in a three-dimensional stress state

Suranaree University of Technology

Hydrostatic stress state is when

1 = 2 = 3
Tapany Udomphol

Jan-Mar 2007

a) Uniaxial

Shear stresses provide driving force for plastic deformation.

b) Biaxial

Hydrostatic stresses cannot contribute to shape change but involve in failure processes

c) Hydrostatic

Tensile crack growth or void formation Compressive hinder crack, close void.

d) Triaxial Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Stress system in (a) sheet processes and (b) bulk processes.

In sheet deformation processes (i.e., sheet metal forming, vacuum forming, blow moulding), the workpiece is subjected to two dimensional biaxial stresses. (also depending on geometry)
Suranaree University of Technology

In bulk deformation processes (i.e. forging, rolling and extrusion), the workpiece is subjected to triaxial stresses, which are normally compressive.
Tapany Udomphol

Jan-Mar 2007

Deformation geometry
Plane stress
Principal stresses 1 and 2 are set up together with their associated strain in the x-y plane. The sheet is free to contact (not constrained) in the 3 (z) direction. There is strain in this direction but no stress, thus 3 = 0., resulting in biaxial stress system. Since the stress are effectively confined to one plane, this stress system is known as plane stress.
Plane stress condition

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Plane strain
Deformation (strain) often occurs in only two dimensions (parallel to 1 and 2). 3 is finite, preventing deformation (strain) in the z direction (constrained), which is known as plane strain. Example: the extrusion of a thin sheet where material in the centre is constrained in the z direction.
Plane strain condition
Suranaree University of Technology
Tapany Udomphol

Jan-Mar 2007

Forming equipments
Forming equipments include

1) Forming presses 2) Dies 3) Tools

www.ptu.tu-darmstadt.de/.../ictmp/img00011.gif

Equipments in sheet metal forming process

Suranaree University of Technology
Tapany Udomphol

Jan-Mar 2007

Forming machines
Using mechanical or hydraulic presses. 1) Mechanical presses - energy stored in a flywheel is transferred to the movable slide on the down stroke of the press. - quick - acting , short stroke. 2) Hydraulic presses - slower - acting, longer stroke.

Shearing machine (mechanical)

Hydraulic deep drawing press

Suranaree University of Technology
Tapany Udomphol

Jan-Mar 2007

Actions of presses
(according to number of slides, which can be operated independently of each other.)

1) Single - action press - one slide - vertical direction 2) Double - action press - two slides - the second action is used to operated the hold-down, which prevents wrinkling in deep drawing. 3) Triple - action press - two actions above the die, one action below the die.

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Example:

Press brake single action

A single action press with a very long narrow bed. Used to form long, straight bends in pieces such as channels and corrugated sheets.

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Tooling
Basic tools used with a metalworking press are the punch and the die.

Punch A convex tool for making holes by shearing , or making surface or displacing metal with a hammer. Die A concave die, which is the female part as opposed to punch which is the male part.

Punches and dies

Die materials: High alloy steels heat treated for the punches and dies.
Tapany Udomphol

Punch and die in stamping

Suranaree University of Technology

Jan-Mar 2007

Compound dies
Several operations can be performed on the same piece in one stroke of the press. Combined processes and create a complex product in one shot. Used in metal stamping processes of thin sheets.

www.lyons.com

Compound die

www.deltatooling.co.jp/

Transfer dies
Transfer dies are also called compounding type dies. The part is moved from station to station within the press for each operation.
Transfer die
Suranaree University of Technology
Tapany Udomphol

Jan-Mar 2007

www.bgprecision.com

Schematic diagram of a die set

A die set is composed of

pilot

1) Punch holder which holds punch plate connected with blanking and piecing punches for cutting the metal sheet. 2) Die block consists of die holder and die plate which was designed to give the desired shape of the product. 3) Pilot is used to align metal sheet at the correct position before blanking at each step. 4) Striper plate used for a) alignment of punch and die blocks b) navigate the punch into the die using harden striper inserts and c) remove the cut piece from the punch.
Suranaree University of Technology
Tapany Udomphol

Jan-Mar 2007

Forming method
There are a great variety of sheet metal forming methods, mainly using shear and tensile forces in the operation.

Progressive forming Rubber hydroforming Bending and contouring Spinning processes Explosive forming

Shearing and blanking Stretch forming Deep drawing

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Progressive forming
Punches and dies are designed so that successive stages in the forming of the part are carried out in the same die on each stroke of the press. Progressive dies are also known as multi-stage dies. Example: progressive blanking and piercing of flat washer.
Punch

washers

Stripper plate Die

The strip is fed from left to right. The first punch is to make the hole of the washer. The washer is then blanked from the strip.

Strip Suranaree University of Technology

washer

The punch A is piercing the hole for the next washer.

Tapany Udomphol

Jan-Mar 2007

Progressive die
Metal sheet used in blanking process
www.hillengr.com

www.bestechtool.com

Progressive die

Optimise the material usage. Determining factors are 1) volume of production 2) the complexity of the shape
Suranaree University of Technology
Tapany Udomphol

Jan-Mar 2007

Rubber hydroforming
Using a pad of rubber or polyurethane as a die. A metal blank is placed over the form block, which is fastened to the bed of a single - action hydraulic press. During forming the rubber (placed in the retainer box on the upper platen of the press) transmits a nearly uniform hydrostatic pressure against the sheet. Pressure ~ 10 MPa, and where higher local pressure can be obtained by using auxiliary tooling.
Guerin process

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Hydroforming
www.egr.msu.edu

Upper fluid chamber

Lower fluid chamber fluid

Draw blank material

Stamp hydroforming machine setup with a fluid supplied from one side of the draw blank

A drawing of hydroforming setup with fluid supplied from to both sides of the materials.

Used for sheet forming of aluminium alloys and reinforced thermoplastics.

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Bending and contouring

Bendmachine

Wiper rolls

Form block

(a) Three-roll bender: sometimes does not provide uniform deformation in thin-gauge sheet due to the midpoint of the span localisation of the strain. Often need the forth roll. (b) Wiper-type bender: The contour is formed by successive hammer blows on the sheet, which is clamped at one end against the form block. Wiper rolls must be pressed against the block with a uniform pressure supplied by a hydraulic cylinder. (c) Wrap forming: The sheet is compressed against a form block, and at the same time a longitudinal stress is applied to prevent buckling and wrinkling. Ex: coiling of a spring around a mandrel.

Clamp Clamp

Tension

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Bending and contouring machines

www.rollfab.com.au www.macri.it

Pipe bending machine

www.diydata.com

www.lathes.co.uk

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Spinning processes
Deep parts of circular symmetry such as tank heads, television cones.

Materials: aluminium and alloys, high strength - low alloy steels, copper, brass and alloys, stainless steel,

(a) Manual spinning

(b) Shear spinning

The metal blank is clamped against a form block, which is rotated at high speed. The blank is progressively formed against the block, by a manual tool or by means of small-diameter work rolls.
Note: (a) no change in thickness but diameter, (b) diameter equals to blank diameter but thicknessTapany Udomphol stays the same. Jan-Mar

Suranaree University of Technology

2007

Explosive forming
Produce large parts with a relatively low production lot size. The sheet metal blank is placed over a die cavity and an explosive charge is detonated in medium (water) at an appropriate standoff distance from the blank at a very high velocity. The shockwave propagating from the explosion serves as a friction-less punch

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Shearing and blanking

Shearing The separation of metal by the movement of two blades operated based on shearing forces. A narrow strip of metal is severely plastically deformed to the point where it fractures at the surfaces in contact with the blades.
(a) Proper clearance Ragged surface

The fracture then propagates inward to provide complete separation. Clearance (normally 2-10% thickness) clean fracture surface. ragged fracture surface. greater distortion, greater energy required to separate metal.
Thickness
Tapany Udomphol

(b) Insufficient clearance blurr

Proper Insufficient Excessive

(c) Excessive clearance Suranaree University of Technology

clearance
Jan-Mar 2007

Maximum punch force

No friction condition. The force required to shear a metal sheet ~ length cut, sheet thickness, shearing strength. The maximum punch force to produce shearing is given by

Pmax 0.7 u hL
where u h L The shearing force = the ultimate tensile strength = sheet thickness = total length of the sheared edge by making the edges of the cutting tool at an inclined angle

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Blanking : The shearing of

close contours, when the metal inside the contour is the desired part.

Punching or piercing :
The shearing of the material when the metal inside the contour is discarded.

Notching : The punch

removes material from the edge or corner of a strip or blank or part.

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

www.americanmachinist.com/

Parting : The simultaneous

cutting along at least two lines which balance each other from the standpoint of side thrust on the parting tool.

Slitting : Cutting or
shearing along single lines to cut strips from a sheet or to cut along lines of a given length or contour in a sheet or workpiece.

Trimming : Operation of
cutting scrap off a partially or fully shaped part to an established trim line.
Suranaree University of Technology
Tapany Udomphol

Jan-Mar 2007

Shaving : A secondary
shearing or cutting operation in which the surface of a previously cut edge is finished or smoothed by removing a minimal amount of stock.

Ironing : A continuous
thinning process and often accompanies deep drawing, i.e., thinning of the wall of a cylindrical cup by passing it though an ironing die.

Fine blanking : Very

smooth and square edges are produced in small parts such as gears, cams, and levers.
Suranaree University of Technology
Tapany Udomphol

Jan-Mar 2007

Bending
A process by which a straight length is transformed into a curved length. produce channels, drums, tanks.

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Bending
The bend radius R = the radius of curvature on the concave, or inside surface of the bend. Fibres on the outer surface are strained more than fibres on the inner surface are contracted. Fibres at the mid thickness is stretched.

Decrease in thickness (radius direction) at the bend to preserve the constancy of volume. R thickness on bending
Tapany Udomphol

Suranaree University of Technology

Jan-Mar 2007

Condition: - No change in thickness - The neutral axis will remain at the centre fibre. - Circumferential stretch on the top surface ea = shrink on the bottom surface, eb R strain

R bend radius h thickness

1 e a = eb = (2 R / h ) + 1

Eq.1

The minimum bend radius

For a given bending operation, the smallest bend radius can be made without cracking on the outer tensile surface. Normally expressed in multiples of sheet thickness.

Example: a 3T bend radius means the metal can be bend

without cracking though a radius equal to three times the sheet thickness T.
Suranaree University of Technology
Tapany Udomphol

Jan-Mar 2007

Effect of b/h ratio on ductility

Stress state is biaxial (2/1 ratio) Width / thickness b/h ratio

b/h

biaxiality

Strain, ductility

Cracks occur near the centre of the sheet

Effect of b/h on biaxiality and bend ductility

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Springback
Dimensional change of the formed part after releasing the pressure of the forming tool due to the changes in strain produced by elastic recovery. Yield stress Elastic modulus

Plastic strain Spring back Springback is encountered in all forming operations, but most easily occurs in bending.
Suranaree University of Technology
Tapany Udomphol

Jan-Mar 2007

For aluminium alloys and austenitic stainless steels in a number of cold-rolled tempers, approximate springback in bending can be expressed by

Ro Ro Ro = 4 +1 3 Rf Eh Eh
Where Ro Rf and Ro < Rf

Eq.2

= the radius of curvature before release of load = the radius of curvature after release of lead

Solutions: compensating the springback by bending to a

smaller radius of curvature than is desired (overbending). By trialand-error. The force Pb required to bend a length L about a radius R may be estimated from 2

Pb =
Suranaree University of Technology

2(R + h / 2 )

o Lh

tan

Eq.3

2
Jan-Mar 2007

Tapany Udomphol

Tube bending
Bending of tube and structural material for industry, architecture, medical, refinery. Heat induction and hot slap bending require the heating of pipe, tube or structural shapes. Heat Induction bending is typically a higher cost bending process and is primarily used in large diameter material.

www.precision-tube-bending.com Suranaree University of Technology

Tapany Udomphol

Tube bending

Jan-Mar 2007

www.dynabil.com

Stretch forming
Forming by using tensile forces to stretch the material over a tool or form block. used most extensively in the aircraft industry to produce parts of large radius of curvature. (normally for uniform cross section). required materials with appreciable ductility. Springback is largely eliminated because the stress gradient is relatively uniform.
Stretch forming feasible for aluminium, stainless steel, titanium.

Suranaree University of Technology

Tapany Udomphol

www.ducommunaero.com Jan-Mar 2007

Stretch forming equipment

Ram

Ram

Using a hydraulic driven ram (normally vertical). Sheet is gripped by two jaws at its edges. Form block is slowly raised by the ram to deform sheet above its yield point. The sheet is strained plastically to the required final shape.

Examples: large thin panel, most complex automotive

stamping involve a stretching component.
Suranaree University of Technology Jan-Mar 2007

Tapany Udomphol

Diffuse necking

(a limit to forming)

In biaxial tension, the necking which occurs in uniaxial tension is inhibited if 2/1 > 1/2, and the materials then develops diffuse necking. (not visible) The limit of uniform deformation in strip loading occurs at a strain equals to the strain-hardening exponent n. = n
u

Localised necking
Plastic instability of a thin sheet will occur in the form of a narrow localised neck. followed by fracture of the sheet. Normal strain along X2 must be zero.

~ 55o for an isotropic

material in pure tension

u = 2n
Jan-Mar 2007

Localised necking in a strip in tension

Suranaree University of Technology
Tapany Udomphol

Deep drawing
The metalworking process used for shaping flat sheets into cup-shaped articles. Examples: bathtubs, shell cases, automobile panels.
Deep drawing of a cylindrical cup

Pressing the metal blank of appropriate size into a shaped die with a punch.

Before drawing

After drawing

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Punch

It is best done with double-action press. Using a blank holder or a holddown ring

Holddown ring

Complex interaction between metal and die depending on geometry. No precise mathematical description can be used to represent the processes in simple terms.

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Flange

A cup is subjected to three different types of deformation.

As the metal being drawn,

Triaxial

Cup wall Punch region

Change in radius
Biaxial

Increase in cup wall

Biaxial

Thickness profile of drawn cup

Stresses and deformation in a section from a drawn cup

Clearance between the punch and the die > 10-20% thickness.

Metal in the punch region is thinned down

biaxial tensile stress.

Metal in the cup wall is subjected to a circumference strain, or hoop and a radial tensile strain. Metal at the flange is bent and straightened as well as subjected to a tensile stress at the same time.
Suranaree University of Technology
Tapany Udomphol

Jan-Mar 2007

Redrawing
Use successive drawing operations by reducing a cup or drawn part to a smaller diameter and increased height known as redrawing. Examples: slender cups such as cartridge case and closedend tubes. 1) Direct or regular redrawing : smaller diameter is produced by means of a hold-down ring. The metal must be bent at the punch and unbent at the die radii see Fig (a). Tapered die allows lower punch load, Fig (b). 2) Reverse or indirect redrawing : the cup is turned inside out the outside surface becomes the inside surface, Fig (c). Better control of wrinkling and no geometrical limitations to the use of a holddown ring.

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Punch force vs. punch stroke

Punch force = Fdeformation + Ffrictional + (Fironing)

Fdeformation Ffrictional Fironing

- varies with length of travel - mainly from hold down pressure - after the cup has reached the maximum thickness.

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Drawability (deep drawing)

Drawability is a ratio of the initial blank diameter (Do) to the diameter of the cup drawn from the blank ~ punch diameter (DP) Limiting draw ratio (LDR)

Do LDR D p
Where

e max

Eq.4

is an efficiency term accounting for frictional losses.

Normally the average maximum reduction in deep drawing is ~ 50%.

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Practical considerations affecting drawability

Die radius should be about 10 x sheet thickness. Punch radius a sharp radius leads to local thinning and tearing. Clearance between punch and die should be about 2040% > sheet thickness. Hold-down pressure about 2% of average o and u. Lubrication of die side - to reduce friction in drawing. Material properties - low yield stress, high work hardening rates, high values of strain ratio of width to thickness R. Since the forming load is carried by the side wall of the cup, failure therefore occurs at the thinnest part. In practice the materials always fails either at (a) the shoulder of the die and (b) the shoulder of the punch.
Suranaree University of Technology
Tapany Udomphol

Jan-Mar 2007

Practical considerations for round and rectangular shells

Different pressures (tension, compression, friction, bending) force the material into shape, perhaps with multiple successive operations.

www.drawform.com

Round shell

Different flow patterns at sides and corners. Corners require similar flow as round shells while sides need simple bending. The corner radii control the maximum draw depth. Centre to center distance of corners 6 x corner radius Bottom radius corner radius
Suranaree University of Technology
Tapany Udomphol

Rectangular shell
Jan-Mar 2007

To improve drawability
To avoid failures in the thin parts (at the punch or flange), metal in that part need to be strengthened, or weaken the metal in other parts (to correct the weakest link). If sufficient friction is generated between punch and workpiece, more of the forming load is carried by the thicker parts. Concerning about crystallographic texture (slip system), degree of anisotropy or strain ratio R.
The dependence of limiting draw ratio on R and work hardening rate, n
Suranaree University of Technology
Tapany Udomphol

Jan-Mar 2007

The plastic strain ratio R measures the normal anisotropy, which denotes high resistance to thinning in the thickness direction.
ln(w / ln(wow)/ w) R = ln(h / h) ln(ho / h) R=
o o

Eq.5

Where wo and w are the initial and final width ho and h are the initial and final thickness. But it is difficult to measure thickness on thin sheets, therefore we have

ln(wo / w) R= ln( wL / wo Lo )

Eq.6

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Example: A tension test on a special deep-drawing steel

showed a 30% elongation in length and a 16% decrease in width. What limiting draw ratio would be expected for the steel?

L Lo = 0.30 Lo w wo = 0.16 wo

L = 1.30 Lo w = 1 0.16 = 0.84 wo

R=

ln( wo / w) ln(1 / 0.84) ln 1.190 = = = 1.98 ln((w / wo )( L / Lo )) ln(0.84 1.30) ln 1.092

From Fig. 20-16 Dieter page 673, the limiting draw ratio ~ 2.7
Suranaree University of Technology Jan-Mar 2007

Tapany Udomphol

Forming limit criteria

Tensile test only provides ductility, work hardening, but it is in a uniaxial tension with frictionless, which cannot truly represent material behaviours obtained from unequal biaxial stretching occurring in sheet metal forming. Sheet metal formability tests are designed to measure the ductility of a materials under condition similar to those found in sheet metal forming.

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007

Erichsen cupping test

Simple and easy. symmetrical and equal biaxial stretching. Allow effects of tool-workpiece interaction and lubrication on formability to be studied. The sheet metal specimen is hydraulically punched with a 20 mm diameter steel ball at a constant load of 1000 kg. The distance d is measured in millimetres and known as Erichsen number.
Results of cupping test on steel sheets.
Suranaree University of Technology Jan-Mar 2007

Tapany Udomphol

The forming limit diagram

The sheet is marked with a close packed array of circles using chemical etching or photo printing techniques. The blank is then stretched over a punch, resulting in stretching of circles into ellipses. The major and minor axes of an ellipse represent the two principal strain directions in the stamping. The percentage changes in these strains are compared in the diagram. Comparison is done in a given thickness of the sheet.
Suranaree University of Technology -40

Grid analysis (a) before (b) after deformation of sheet. Major strain 1(%)
120 100

Failure
80

2 1

60 40 20

2
Safe

AK steel

-20

Minor strain 2(%)

20

40

60

80

100

Forming limit diagram

Tapany Udomphol

Jan-Mar 2007

Example: A grid of 2.5 mm circles is electroetched on a blank of

sheet steel. After forming into a complex shape the circle in the region of critical strain is distorted into and ellipse with major diameter 4.5 mm and minor diameter 2.0 mm. How close is the part to failing in this critical region?
Major strain 1(%)

Major strain

120

100

4.5 2.5 e1 = 100 = 80% 2.5

Minor strain

Failure A Safe B AK steel

80

2 1

60 40 20

2.0 2.5 e2 = 100 = 20% 2.5

-40

-20

Minor strain 2(%)

20

40

60

80

100

Forming limit diagram

The coordinates indicate that the part is in imminent danger of failure.

Suranaree University of Technology
Tapany Udomphol

Jan-Mar 2007

Defects in formed parts

www.bgprecision.com

Springback problem

Edge conditions for blanking. Local necking or thinning or buckling and wrinkling in regions of compressive stress. Springback tolerance problems. Cracks near the punch region in deep drawing minimised by increasing punch radius, lowering punch load.
Tapany Udomphol

Crack near punch region

Suranaree University of Technology

Jan-Mar 2007

 Radial cracks in the flanges and edge of the cup due to not sufficient ductility to withstand large circumferential shrinking. Wrinkling of the flanges or the edges of the cup resulting from buckling of the sheet (due to circumferential compressive stresses) solved by using sufficient hold-down pressure to suppress the buckling. Surface blemishes due to large surface area. EX: orange peeling especially in large grain sized metals because each grain tends to deform independently use finer grained metals. Mechanical fibering has little effect on formability. Crystallographic fibering or preferred orientation may have a large effect. Ex: when bend line is parallel to the rolling direction, or earing in deep drawn cup due to anisotropic properties.
Earing in drawn can
aluminium.matter.org.uk Suranaree University of Technology
Tapany Udomphol

Jan-Mar 2007

 Stretcher strains or worms (flamelike patterns of depressions). Associated with yield point elongation. The metal in the stretcher strains has been strained an amount = B, while the remaining received essentially zero strain. The elongation of the part is given by some intermediate strain A.
Stretcher strain in low-carbon steel.

A B

The number of stretcher strains increase during deformation. The strain will increase until the when the entire part is covered it has a strain equal to B. Solution: give the steel sheet a small cold reduction (usually 0.5-2% reduction in thickness). Ex: temper-rolling, skin-rolling to eliminate yield point.
Tapany Udomphol

Relation of stretcher strain to stress strain curve.

Suranaree University of Technology

Jan-Mar 2007

References

Dieter, G.E., Mechanical metallurgy, 1988, SI metric edition, McGraw-Hill, ISBN 0-07-100406-8. Edwards, L. and Endean, M., Manufacturing with materials, 1990, Butterworth Heinemann, ISBN 0-7506-2754-9.

Suranaree University of Technology

Tapany Udomphol

Jan-Mar 2007