Introduction to the Synchronous Digital Hierarchy (SDH)

The History of Digital Transmission

70s - introduction of PCM into Telecom networks 32 PCM streams are Synchronously Multiplexed to 2.048 Mbit/s (E1) Multiplexing to higher rates via PDH 1985 Bellcore proposes SONET 1988 SDH standard introduced.

PDH: Plesiochronous Digital Hierarchy

Multiplex levels:
2.048 Mbit/s 8.448 Mbit/s 34.368 Mbit/s 139.264 Mbit/s

Uses Positive justification to adapt frequency differences Overheads: CRC Defects: LOS, LOF, AIS

Plesiochronous Multiplexing

Before SDH transmission networks were based on the PDH hierarchy. Plesiochronous means nearly synchronous. 2 Mbit/s service signals are multiplexed to 140 Mbit/s for transmission over optical fiber or radio. Multiplexing of 2 Mbit/s to 140 Mbit/s requires two intermediate multiplexing stages of 8 Mbit/s and 34 Mbit/s. Multiplexing of 2 Mbit/s to 140 Mbit/s requires multiplex equipment known as 2, 3 and 4 DME. Alarm and performance management requires separate equipment in PDH.

PDH vs. SDH Hierarchy

PDH transmission rates: SDH is designed to unify all transmission rates into a single Mapping hierarchy
Japan North America Europe

397.2 M bit/s x4 97.728 M bit/s x3 32.084 M bit/s x5 6.312 M bit/s x4 274.176 M bit/s x6 44.738 M bit/s x7 6.312 Mbit/s x4 x 4 1.544 M bit/s 2.048 M bit/s 139.264Mbit/s x 4 34.368 Mbit/s x 4 8.448 M bit/s

PDH Multiplexing

PDH Multiplexing of 2 Mbit/s to 140 Mbit/s requires 22 PDH multiplexers:

16 x 2DME 4 x 3DME 1 x 4DME

Also a total of 106 cables required.

2 Mb it/s 8 Mbi t/s 3 4 Mb it/s 140 Mbi t/s 1 2 D M E

3 D M E 4 D M E 3 D M E

64

2 D M E

PDH Add/Drop

If a small number of 2 Mbit/s streams passing through a site need to be dropped then in PDH this requires large amount of equipment to multiplex down to 2Mbit/s.

What is SDH?

The basis of Synchronous Digital Hierarchy (SDH) is synchronous multiplexing - data from multiple tributary sources is byte interleaved. In SDH the multiplexed channels are in fixed locations relative to the framing byte. Demultiplexing is achieved by gating out the required bytes from the digital stream. This allows a single channel to be dropped from the data stream without demultiplexing intermediate rates as is required in PDH.

SDH Rates

SDH is a transport hierarchy based on multiples of 155.52 Mbit/s The basic unit of SDH is STM-1:
STM-1 STM-4 STM-16 STM-64 = = = = 155.52 Mbit/s 622.08 Mbit/s 2588.32 Mbit/s 9953.28 Mbit/s

Each rate is an exact multiple of the lower rate therefore the hierarchy is synchronous.

SDH Hierarchy

SDH defines a multiplexing hierarchy that allows all existing PDH rates to be transported synchronously. The following diagram shows these multiplexing paths:
x1 STM-N xN x3 AUG AU-4 VC-4 x3 x1 TUG-3 TU-3 VC-3 44736 kb/s (DS3) 34368 kb/s HOP 139264 kb/s C-4

AU-3

VC-3 x7 x7 TUG-2 x3
TU-12

C-3

x1 TU-2 VC-2 C-2 6312 kb /s (DS2) LOP 204 8 kb/s

TU-11

VC-12

C12

x4 VC-11 C-11

154 4 kb/s (DS1)

Example: Multiplex path for the E1

xN STM-N AUG AU-4 VC-4

x3 TUG-3

x7 TUG-2

x3 TU-12 VC-12 C-12

Section overhead Pointer processor HO path overhead Pointer processor LO path overhead

Transport of PDH payloads

SDH is essentially a transport mechanism for carrying a large number of PDH payloads. A mechanism is required to map PDH rates into the STM frame. This function is performed by the container (C). A PDH channel must be synchronised before it can be mapped into a container. The synchroniser adapts the rate of an incoming PDH signal to SDH rate.

SDH and non-synchronous signals

At the PDH/SDH boundary Bit stuffing is performed when the PDH signal is mapped into its container.
Bit stuffing

PDH

SDH

SDH virtual Containers

Once a container has been created, path overhead byte are added to create a virtual container. Path overheads contain alarm, performance and other management information. A path through an SDH network exists from the point where a PDH signal is put into a container to where the signal is recovered from the container. The path overheads travel with the container over the path.

Mapping Virtual Containers

C-4 container being mapped into an STM frame via a VC-4 virtual container
Container-4

VC-4 POH

Container-4

VC-4

AU-4 PTR

VC-4

AU-4

AU-4 PTR

VC-4

AUG

SOH Logical association Physical association

AUG

AUG

STM-N

T1517990-95

NOTE Unshaded areas are phase aligned. Phase alignment between the unshaded and shaded areas is defined by the pointer (PTR) and is indicated by the arrow.

2 Mbit/s PCM30 frame structure

The SDH frame rate is inherited from PCM. As with PCM, the SDH has 8 bits per time slot. As with PCM, the SDH frame rate in 125 us per frame. The following diagram shows the PCM30 frame:

125 us

TS0 TS1

TS15 TS16 TS17

TS30 TS31 TS0

Basic SDH frame structure

STM-N frame structure is shown in the Figure below. The three main areas of the STM-N frame are indicated:
SOH; Administrative Unit pointer(s); Information payload.
270 N columns (bytes) 9N 261 N

Section overhead SOH Administrative unit pointer(s) STM-N payload Section overhead SOH 9 rows

3 4 5

9
T15180 00-9 5

Different clock rates in SDH

SDH will still work if there are two different clocks in the network and the network becomes asynchronous. Pointers are used adjust for the new frequency.

Pointer processing ocurrs here

STM -N NE #1

S TM -N N E #2

STM -N

f +f

Administrative Units in the STM-N

The VC-4 is mapped into an STM frame via the administrative group (AU). The VC-4 associated with each AU-4 does not have a fixed phase with respect to the STM-N frame. The location of the first byte of the VC-n is indicated by the AU-n pointer.
N 2 7 0 b yt e s
N 9

N 2 6 1 b yt e s

S T M -N

RS OH

A U -n P T R s
J1 B3

V C -4 -X c

M SO H

C2 G 1 F2 H4 F3 K3 N1 1 X- 1

F ix e d st u f f

C - 4 -X c

X 260 X 2 6 1 b y te s

T 1 5 18 2 3 0 - 95

P TR

P o in t e r

Tributary Units in a VC-4

The VC-4 can carry a container -4 (C-4). The C4 carries a 140 Mbit/s PDH signal. The VC-4 forms what is known as an high order path. If lower speed PDH signals need to be transported these are mapped into a tributary unit (TU). The TUs are then multiplexed into a VC-4. The VC-n associated with each TU-n does not have a fixed phase relationship with respect to the start of the VC4. The TU-n pointer is in a fixed location in the VC-4 and the location of the first byte of the VC-n is indicated by the TUn pointer.

Tributary Units in a VC-4

86 Columns TUG-2 TU-1 PTRs

.. ..

TUG-2 TUG-3 (7 TUG-2) POH

TU-2 PTR

Fixed stuff

Fixed stuff

POH ..... ...

POH

VC-2

VC-1

..

..

PTR Pointer 3 VC-12s or 4 VC-11s in 1 TUG-2

T1518100-95

Tributary units 2 Mbit/s are mapped asynchronously into a VC-12. VC-12s are distributed over four frames known as a VC multiframe. The figure shows this over a period of 500 s. V5 byte:

V5 RR R RR RR R

32 bytes
RR R RR RR R J2 C1 C2 O O O O R R

32 bytes
R RR RR RR R N2 C1 C2 O O O O R R

140 bytes

32 bytes
R RR RR RR R K4 C 1 C2 R R R R R S 1 S2 D D D D D D D

31 bytes
R RR RR RR R
T1523020-96

D R O S C

Data bit Fix ed stuff bit Overhead bit Justification opportunity bit Justification c ontrol bit

BIP-2 1 2

REI 3

RFI 4

Signal Label 6 7

RDI 8

STM Section Overheads

9 Bytes

Nine rows of nine bytes at the front of the SDH frame form the section overhead. The first three rows are the regenerator section overhead. The last six rows are the multiplex section overhead.

A1 A1 A1 A2 A2 A2 J0 B1 D1 9 rows B2 B2 B2 K1 D4 D7 D10 D5 D8 D11 K2 D6 D9 D12 MSOH E1 E1 D2 F1 D3 RSOH

S1 Z1 Z1 Z2 Z2 M1 E2 E2

VC-4 path overheads

The first column of the VC-4 is the VC-4 path overhead. The overheads have been modified in the latest release of G.707

Old VC-4 POH

J1 B3 C2 G1 9 rows F2 H4 Z3 Z4 Z5

new VC-4 POH

J1 B3 C2 G1 9 rows F2 H4 F3 K3 N1

VC-12 overhead
old VC-12 OH
VC-12

new VC-12 OH
VC-12 V5 125 us 35 by tes 125 us 35 by tes

The first byte of the VC-12 is the VC-12 path overhead. The VC-12 frame is spread over four frames to form a VC-12 multiframe. Each of the four frames in the multiframe contains an overhead byte. The overheads have been modified in the latest release of G.707

V5

J2 125 us 35 by tes

J2 125 us 35 by tes

Z6 125 us 35 by tes

N2 125 us 35 by tes

Z7 125 us 35 by tes

K4 125 us 35 by tes

V5 Byte

The bits in the V5 byte are allocated as follows:

BIP-2 1 2

REI 3

RFI 4 5

Signal Label 6 7

RDI 8

Framing bytes (A1 & A2)

The framing byte locate the beginning of the STM frame

Byte A1 A2

comments First framing byte A1:11110110 Second framing byte A2:00101000

Synchronisation status marker byte (S1).

The synchronisation status marker byte contains information about the quality of the embedded timing
Byte S1 comments Synchronistion status marker byte S1 Byte: bit 5 -8 0000 Quality unknown 0010 Traceable to PRC G.811 0100 Traceable to Transit G.812 1000 Traceable to Local G.812 1011 Derived from SETS 1111 Don't use for Synchronisation. Other bytes are reserved.

Bit interleaved parity (B1, B2, B3)

The BIP is calculated over the previous frame/multiframe

BIP Bits & Bytes Coverage B1 parity - Entire frame B2 parity: Mux OH + AU-4

Regen OH 9 rows AU-4 9 rows

Regen OH AU-4

Mux OH

Mux OH

9 column s

261 co lumns

9 columns

26 1 columns

B3 parity - Virtual Container

AU-4 Regen OH
VC-4

V5 bits 1 & 2: TU-12 frame

AU-4 Regen OH 9 rows
Path TU-1 2 poin ter VC-4 Path OH

VC-4 Payload

9 rows
Path

VC-4 Payload

T U-12 Mux OH
OH

Mux OH

OH

Payload

9 column s

261 co lumns

9 columns

26 1 columns

Bit interleaved parity (B1, B2, B3)

Byte B1 B2 #1,2,3

B3

V5

comments Bit interleaved parity - 8 bits for entire previous frame before scrambling. Three bytes of a 24 bit multiplex section bit interleaved parity - Calculated over the previous STM-1 frame excluding the first three rows of the SOH before scrambling. Bit interleaved parity - 8 bits for entire previous frame before scrambling. The BIP is calculated over the previous VC-4. VC-12 path bit interleaved parity - 2 bits for previous frame The BIP is calculated over the previous VC-12 frame including VC-12 path overheads but excludes V1, V2, V3.

Orderwire (E1 & E2)

The E byte carry the orderwire channels. The relief byte is used for ring protection

E1 Regenerator section orderwire E2 Multiplex section orderwire

DCC channels (D1 to D3 and D4 to D12)

The DCC channels are used Element Management Software to pass management information between sites.

Byte D1 to D3

comments Regenerator section data communications channel (DCC) The D1 to D3 bytes are a 192 kbit/s DCC channel. Multiplex section data communications channel The D4 to D12 bytes are a 576 kbit/s DCC channel.

D4 to D12

User channels (F1, F2, F3 & N2)

The user channels appear at a front panel connector for use by the network operator.
Byte F1 User channel comments 64 kbit/s user channel. The FLX150/600 supports either G.703 co-directional or contradirectional interface. This user channel can be passed through at a regenerator. VC-4 path user channel VC-4 path user channel Network operator byte -

F2 Z3 (F3) Z6 (N2)

Section/Path trace bytes (J0, J1, J2)

The section/path trace supports a string assigned to a path, this verifies continued connection to the intended transmitter

Byte J0

comments Regenerator section trace use is not defined in ITU-T. Trace value can be entered for section id between national boundaries. ITU-T: High order path access point identifier. Path trace byte

J1 J2

Remote error indication

MS REI (M1) Indicates the count of the interleaved bit blocks (1 to N) that have detected an error.

Byte M1

comments Multiplex section remote error indication (MS REI)

High order path management

Signal label (C2)

Byte C2 com m en ts Signal label: This byte indicates the composition of the VC-4 .

Path Status
Byte G1 comments Path status byte. This byte is sent from the receiver back to the originator.

Multiframe Pointer
Byte H4 comments VC-4 multiframe pointer. Indicates the multiframe position indicator for the VC-12

Low order path management

The VC-12 path overhead signals are held in the V5 byte.

Byte V5 bit 3 V5 bit 4 V5 bit 5-7 V5 bit 8 Comments Remote error indication (REI): set to one if one or more error is detected at receiver in the BIP-2. Standard implementation on FLX and FLM Remote failure indication (RFI). Set to one if a failure is declared . VC-12 signal label. VC-12 path remote defect indication (RDI) Set to 1 if an AIS or a signal failure condition is received.

SDH layers

The following diagram shows 2Mbit/s multiplexed to STM1. The transmission path passes through five layers in this connection.
SDH
Low er O rder Pat h Lay er

PDH LPA
Cr os s Connec tion

LPT

LPC HPA

Higher O rder Pat h Lay er

Cross Connec tion

HPT

H PC
M ultiple xer S ection Lay er

M SA M ST

Regenerator S ection Lay er P hys ica l M edia Lay er

RSA R ST

S PI

PPI

Termination points

Within a layer each path ends at a termination point A path in SDH can be visualised as a pipe, In the diagram the 140Mbit/s path passes unaltered through the multiplex section0
hi gh or de r p ath M ux se ctio n 1 40 Mb it/s A DM A DM 14 0 M bi t/s

S TM-1 ring

A DM

A DM

140 Mbit/ s in S ection O H in Se ction O H out

140 M bit/s out

Layers - Example

V C - 12 P at h r e m a in s u n in te r r u p te d b e tw e e n te r m in a tio n p o in ts
M u x s e ct io n M u x se ct io n E1 AD M M ux s e ct io n R egen s e c tio n R egen s e c tio n E1

S T M -1 r in g

A DM

D X C 4 /4

Te rm in a l

ST M - 1
E1

ST M-4

L ow e r O rd e r P a th L a ye r H ig h e r O rd e r P a th L a ye r M u ltip le x S e c tio n L a ye r R eg e ne r ato r S e c tio n L a ye r P hy s ic a l in ter fac e L a ye r

V C - 12 te rm in atio n

V C -1 2 X -c o n ne c t

V C -4 X - c on n ec t

R e ge n

V C -1 2 T e rm in atio n

Alarms and layers

STM Physical Media Layer R eg en er ator Sectio n Layer Mu ltiplexer Sectio n Layer

Each defect indication is associated with a layer

H igher Order Path Layer

E1

Low order path Mux section E1 ADM

Lo wer Order Path Layer

STM-1 ring

ADM

Signalling interactions

Each signal has a consequent action. These are described in the G.782 diagram
P h y s ic a l Se c tio n Re g e n Se c tio n M u ltip le x Se c t io n H ig h e r O rd e r P a t h Lo w e r O rd e r P a t h

SPI

RST

N o te 1

M ST

M SA

HPO M

H UG

H PC

HPT

HPA

LP O M

LU G

LP C

L PT

LP A

LO S "1 " LO F R S- B IP E r ro r ( B 1 ) R e g e n s ig n a l p a s se d "1 " th ro u g h "1 " M S- A I S M S- Ex c Er ro r (B 2 ) A U - A IS "1 "

A IS F EB E F ER F LO S LO F LO M LO P T IM SL M U N EQ

D e te c ti o n G e n e ra ti o n In s e rti o n o f A IS s i g n a l A l a rm In d i c a t o n Si g n a l i F a r e n d b l o c k e rr o r F a r e n d re c e i v e f a i l u r e Lo s s of s ig na l L o s s o f fr a m e L o ss o f m u l t i fra m e L o s s o f p o i n te r T ra c e i d e n ti f i e r m i s m a tc h Si g n a l l a b e l M i s m a tc h Un e q u p p e d si g n a l p e r G 7 0 9 i

M S- B IP E rr o r ( B 2 )

M S- FE R F M S- FE R F "1 " A U - A IS A U - LO P H O P a t h s ig n a l p a s s e d H O V C w it h PO H a n d th r o u g h p a y lo a d "1 " U n u se d H PC O u t p u t / HP- UN EQ

u n s p e c if ie d

H O u n e q u ip p e d

s ig n a l HP- UN EQ H P - TIM H P - SL M H P -B IP E rr o r ( B 3) H P - FE B E H P - FE R F H P - FE R F H P - FE B E TU - A IS H P - LO M / TU -L O P U n u se d LP C O u t p u t / L P -U N EQ p a y lo a d "1 " "1 " TU - A IS "1 "

L O P a t h s ig n a l p a s s e d t h r o u g h L O VC w it h P O H a n d u n s p e c if ie d

L O u n e q u ip p e d

sig n a l LP - U N EQ "1 " LP - TIM LP - SLM L P -B IP Er ro r ( V 5 ) LP - FE B E LP - FE R F LP - FE R F LP - FE B E

SD H M a in t e n a n c e

Sig n a l In t e r a c t io n

G .7 8 2 1 0 N o v e m b e r 1 9 92

SETS: Synchronous Equipment Timing Source

The SETS function controls the selection of the timing source to be used as a reference in the SDH equipment The SETG function is a DPLL function that smoothes the clock and provides holdover on loss of clock.

Select A

Select C

Output clk

STM-N in PDH in Ext ref

Select B

Sys clk SETG

Sync distribution in the SDH network

SDH can be used as a timing transport in a telecommunications network. In this case a SETG (DPLL) is in the clock path at each network element (NE) Timing The PRC is the network recovery providers primary reference clock The G.812 clock is the network providers exchange clock.

PRC

PRC

1 NE

st

1 NE

st

2 NE

nd

2 NE

nd

Timing recovery

N NE

th

N NE

th

G.812 clock

G.812 clock