Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 46 views

    2d Truss

    Uploaded by

    bapu28
    This document provides instructions for using ANSYS to analyze a 2D truss structure. It describes the steps to define the geometry of the truss using keypoints and lines, apply material properties and mesh the model, apply loads and constraints, then solve the system to determine the nodal deflections, reaction forces and stresses in the truss members.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PPTX, PDF, TXT or read online from Scribd

    2d Truss

    Uploaded by

    bapu28
    46 views19 pages
    This document provides instructions for using ANSYS to analyze a 2D truss structure. It describes the steps to define the geometry of the truss using keypoints and lines, apply material properties and mesh the model, apply loads and constraints, then solve the system to determine the nodal deflections, reaction forces and stresses in the truss members.

    Original Description:

    about how 2 design 2d truss in ansys

    Original Title

    2d truss

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PPTX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for using ANSYS to analyze a 2D truss structure. It describes the steps to define the geometry of the truss using keypoints and lines, apply material properties and mesh the model, apply loads and constraints, then solve the system to determine the nodal deflections, reaction forces and stresses in the truss members.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PPTX, PDF, TXT or read online from Scribd
    Download as pptx, pdf, or txt
    46 views19 pages

    2d Truss

    Uploaded by

    bapu28
    This document provides instructions for using ANSYS to analyze a 2D truss structure. It describes the steps to define the geometry of the truss using keypoints and lines, apply material properties and mesh the model, apply loads and constraints, then solve the system to determine the nodal deflections, reaction forces and stresses in the truss members.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PPTX, PDF, TXT or read online from Scribd
    Download as pptx, pdf, or txt
    of 19

    STRUCTURAL DESIGN & ANALYSIS

    Two Dimensional Truss

    Determine the nodal deflections, reaction forces, and stress for the truss system shown below (E = 200GPa, A =3250mm2).

    Preprocessing: Defining the 1. Give the Simplified Version a Title (such as 'Bridge Truss Tutorial'). Problem

    In the Utility menu bar select File > Change Title:

    2. Enter Keypoints

    KEY POINTS 1 2 3 4 5 6 7 0 1800 3600 5400 7200 9000 10800

    X 0 3118 0 3118 0 3118 0

    Units

    Note the units of measure (ie mm) were not specified. It is the responsibility of the user to ensure that a consistent set of units are used for the problem; thus making any conversions where necessary.

    3. Form Lines
    In the main menu select: Preprocessor > Modeling > Create > Lines > Lines > In Active Coord

    The following window will then appear:

    When you're done, click on 'OK' in the 'Lines in Active Coord' window, minimize the 'Lines' menu and the 'Create' menu. Your ANSYS Graphics window should look similar to the following figure.

    4. Define the Type of Element


    From the Preprocessor Menu, select: Element Type > Add/Edit/Delete : : :

    5. Define Geometric Properties


    In the Preprocessor menu: select Real Constants > Add/Edit/Delete

    6. Element Material Properties


    In the 'Preprocessor' menu select: Material Props > Material Models

    7. Mesh Size
    

    In the Preprocessor menu select: Meshing > Size Cntrls > ManualSize > Lines > All Lines

    8. Mesh
    In the 'Preprocessor' menu select : Meshing > Mesh > Lines and click 'Pick All' in the 'Mesh Lines' Your model should now appear as shown in the following window

    Solution Phase: Assigning Loads and Solving


    

    1. Define Analysis Type 2. Apply Constraints

    3. Apply Loads

    4. Solving the System

    Postprocessing: Viewing the Results


    

    Reaction Forces

    Deformation

    Deflection

    Axial Stress

    You might also like