Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 71 views

    Triodeguy Kt88aud

    Uploaded by

    Tudor Gabriel Gavrilescu
    This document provides a circuit diagram and instructions for setting up a parallel push-pull amplifier with KT88 output tubes. It lists all the component values and voltages for the drive and output stages. The instructions specify initially setting the bias potentiometers to the most negative end, then adjusting each to 1.62V after warmup, and finally to 2.01V for a bias current of 65mA. It also recommends metal film and film capacitors from specific manufacturers.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Triodeguy Kt88aud

    Uploaded by

    Tudor Gabriel Gavrilescu
    71 views1 page
    This document provides a circuit diagram and instructions for setting up a parallel push-pull amplifier with KT88 output tubes. It lists all the component values and voltages for the drive and output stages. The instructions specify initially setting the bias potentiometers to the most negative end, then adjusting each to 1.62V after warmup, and finally to 2.01V for a bias current of 65mA. It also recommends metal film and film capacitors from specific manufacturers.

    Original Title

    Triodeguy kt88aud

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides a circuit diagram and instructions for setting up a parallel push-pull amplifier with KT88 output tubes. It lists all the component values and voltages for the drive and output stages. The instructions specify initially setting the bias potentiometers to the most negative end, then adjusting each to 1.62V after warmup, and finally to 2.01V for a bias current of 65mA. It also recommends metal film and film capacitors from specific manufacturers.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    71 views1 page

    Triodeguy Kt88aud

    Uploaded by

    Tudor Gabriel Gavrilescu
    This document provides a circuit diagram and instructions for setting up a parallel push-pull amplifier with KT88 output tubes. It lists all the component values and voltages for the drive and output stages. The instructions specify initially setting the bias potentiometers to the most negative end, then adjusting each to 1.62V after warmup, and finally to 2.01V for a bias current of 65mA. It also recommends metal film and film capacitors from specific manufacturers.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    +650/+655V R7 121k/1W R6 100k/1W 218V RCA XLR G 1 3 + 2 R1 100k R2 511R VT1a 6SL7 R3 2k R4 127k/1W R24 127k/1W NE-2H R21

    100k SW3 R22 511R R23 2k R5 127k/1W R8 1k -255/-260V R11 33.2k/2W R31 33.2k/2W R10 38.3k/2W R9 2k VT2a 6SN7 VT3a 6SN7 C1 0.22u 650V C7 20u/1200V

    +545/+550V C9 20u/630V * Kiwame 2W / 1000V

    445V R12 1k

    VT4 KT88 R36 1k R37 100k/1W

    R40 330R*

    R41 1k

    R45 330R* VT5 KT88

    Bartolluci Model 555 Primary; 300H, 3800ohm P-P

    +212V

    R38 30.9R

    R39 10k

    R44 10k

    R43 30.9R

    BIAS TEST POINTS (2.01V = 65mA) R48 30.9R R46 1k VT6 KT88 R47 100k/1W R56 32.4k VR1 25k R58 100k C3 0.22u 200V VR2 25k R59 100k C4 0.22u 200V -102V Rev. C 6/7/2001 330R* R50 R51 1k R53 30.9R VT7 KT88 330R* R55

    R25 127k/1W C5

    R30 38.3k/2W R29 2k VT2b 6SN7 C2 0.22u 650V

    R49 10k

    R54 10k

    OUT (8ohm SHOWN)

    VT1b 6SL7

    20u/630V R28 1k

    For unbalanced input (RCA) close SW3. R26 100k/1W R27 121k/1W

    R32 1k

    VT3b 6SN7 SET-UP: 1/ Each bias potentiometer should be set initially at the most negative end of the range. After 5 minutes warm-up adjust each bias setting to 1.62V+/-0.01V (50mA). 2/ After 20 minutes warm-up with the amplifier 'right side up' supply voltages should be adjusted to within the values shown Re-adjust after a further hour. 3/ Now adjust each bias setting to 2.01V +/-0.01V for 65mA (or to a value corresponding with the intended bias current.) Note: With new tubes, the bias current can be expected to drift significantly for the first 24-48 hours. 4/ Node voltages are given for diagnostic purposes only and will vary with the individual tubes used. +650/+655V

    RECOMMENDED COMPONENTS: Resistors, Holco metal film; H4 (1/2W, 1%) and H2 (1W, 1%) Roerderstein Metal Film MK8 (2W, 2%) unless stated otherwise. Large capacitors, Solen or AEON film. Small capacitors, Multicap PPFX. Coupling capacitors, VTV "Ultra-Tone". This document & the information herein is the sole property of Richard F. Sears and shall not be used for commercial purposes without the express written permission of Richard F. Sears. (richard@triodeguy.com)

    R57 17.8k C11 5u 200V

    KT88 (TRIODE) - 60W


    PARALLEL PUSH-PULL AMPLIFIER DRIVE & OUTPUT STAGE (Pg 1 of 3) PROGRAM FILES\DATA\KT88_AUD RICHARD F. SEARS 12/3/2000

    You might also like