Service Manual: DSC-H5

DSC-H5
SERVICE MANUAL
Ver. 1.1 2006. 06
Revision History How to use Acrobat Reader LEVEL
Internal memory ON BOARD
US Model Canadian Model AEP Model UK Model E Model Australian Model Chinese Model Brazilian Model Hong Kong Model Korea Model Tourist Model Japanese Model
Link
SPECIFICATIONS SERVICE NOTE DISASSEMBLY BLOCK DIAGRAMS FRAME SCHEMATIC DIAGRAM SCHEMATIC DIAGRAMS PRINTED WIRING BOARDS REPAIR PARTS LIST
Precaution on Replacing the SY-150 board

Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note : Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.
DIGITAL STILL CAMERA
DSC-H5_L2
9-852-117-31
Sony EMCS Co.
2006F1600-1 2006.06 Published by Kohda TEC
These specifications are extracted from Users Guide/ Troubleshooting of DSC-H5 (2-673-176-11 (1)).
SPECIFICATIONS
Camera
[System]
Image device 7.20 mm (1/2.5 type) color CCD, Primary color filter Total pixel number of camera Approx. 7 410 000 pixels Effective pixel number of camera Approx. 7 201 000 pixels Lens Carl Zeiss Vario-Tessar 12 zoom lens f = 6.0 72.0 mm (36 432 mm when converted to a 35 mm still camera) F2.8 3.7
[Input and Output connectors]

A/V OUT jack (Monaural) Minijack Video: 1 Vp-p, 75 , unbalanced, sync negative Audio: 327 mV (at a 47 k load) Output impedance 2.2 k USB jack mini-B
Dimensions
113.283.094.0 mm (4 1/2 inches 3 3/8 inches 3 3/4 inches) (W/H/D, excluding protrusions) Approx. 554 g (1 lb 3.5 oz) (including two batterries, shoulder strap, adaptor ring, lens hood, lens cap, etc.) Electret condenser microphone Dynamic speaker Compatible
Mass
Microphone Speaker Exif Print
USB communication Hi-Speed USB (USB 2.0 compliant)
[LCD screen]
LCD panel 7.5 cm (3.0 type) TFT drive Total number of dots 230 400 (960240) dots
PRINT Image Matching III Compatible PictBridge Compatible
Exposure control Automatic exposure, Shutter speed priority, Aperture priority, Manual exposure, Scene Selection (7 modes) White balance Automatic, Daylight, Cloudy, Fluorescent, Incandescent, Flash, One push
BC-CS2A/CS2B Ni-MH battery charger

Power requirements AC 100 to 240 V, 50/60 Hz, 3W Output voltage AA: DC 1.4V 400 mA 2 AAA: DC 1.4 V 160 mA 2
[Finder]
Panel 0.5 cm (0.2 type) color Total number of dots Approx. 200 000 dots equivalent
File format (DCF compliant) Still images: Exif Ver. 2.21 JPEG compliant, DPOF compatible Movies: MPEG1 compliant (Monaural) Recording media Internal Memory (30 MB) Memory Stick Duo Flash Flash range (ISO set to Auto): approx. 0.3 m to 9.0 m (11 7/ 8 inches to 29 feet 6 3/8 inches) (W)/approx. 0.9 m to 6.8 m (35 1/2 inches to 22 feet 3 3/ 4 inches) (T) Electric viewfinder (color)
[Power, general]
Power HR 15/51:HR6 (size AA) Nickel-Metal Hydride batteries (2), 2.4 V LR6 (size AA) alkaline batteries (2), 3 V ZR6 (size AA) Oxy Nickel Primary Battery (2), 3 V AC-LS5K AC Adaptor 4.2 V Power consumption (during shooting with the LCD screen) 1.4 W Operating temperature 0 to 40C (32 to 104F) Storage temperature 20 to +60C (4 to +140F)
Operating temperature 0 to +40C (+32 to +104F) Storage temperature 20 to +60C (4 to +140F) Dimensions Approx. 713091 mm (2 7/81 3/163 5/8 inches) (W/H/D) Approx. 90 g (3 oz)
Mass
Design and specifications are subject to change without notice.
Viewfinder
DSC-H5_L2
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
2. 3.
4.
5. 6.
: LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PISES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPMENTS PUBLIS PAR SONY.
CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
DSC-H5_L2
TABLE OF CONTENTS 1. SERVICE NOTE
1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY 1-1 1-2. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY 1-2 1-3. PRECAUTION ON REPLACING THE SY-150 BOARD 1-3 1-4. VIDEO OUT DEFAULT DATA CHECK 1-3 1-5. INITIAL LANGUAGE DATA CHECK 1-3
2.
DISASSEMBLY
2-1. DISASSEMBLY 2-3
3.
3-1. 3-2. 3-3. 3-4.
BLOCK DIAGRAMS
OVERALL BLOCK DIAGRAM (1/2) 3-1 OVERALL BLOCK DIAGRAM (2/2) 3-2 POWER BLOCK DIAGRAM (1/2) 3-3 POWER BLOCK DIAGRAM (2/2) 3-4
4.
4-1. 4-2. 4-3. 4-4.
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

FRAME SCHEMATIC DIAGRAM 4-1 SCHEMATIC DIAGRAMS 4-5 PRINTED WIRING BOARDS 4-25 MOUNTED PARTS LOCATION 4-32
5.
REPAIR PARTS LIST
5-1. EXPLODED VIEWS 5-3 5-2. ELECTRICAL PARTS LIST 5-10
DSC-H5_L2
1. SERVICE NOTE
1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY
Self-diagnosis display C: ss: ss The contents which can be handled by customer, are displayed. E: ss: ss The contents which can be handled by engineer, are displayed.
Display Code C:32:ss Countermeasure Turn the power off and on again. Cause Trouble with hardware. Caution Display During Error SYSTEM ERROR FORMAT ERROR MEMORY STICK ERROR INTERNAL MEMORY ERROR
Format the Memory Stick or internal Memory Stick or internal memory is memory. unformatted. C:13:ss Insert a new Memory Stick. Turn the power off and on again. E:61:ss E:62:ss E:91:ss E:92:ss Checking of lens drive circuit. Inspect angular velocity sensor peripheral circuits. Checking of flash unit or replacement of flash unit. (Note) Insert a batteries correctly. Memory Stick is broken. Trouble with internal mamory. When failed in the focus zoom initialization. Steady shot function does not work well. Abnormality when flash is being charged. Batteries are pack is not inserted correctly.
Note : After repair, be sure to execute the Initialize of the setup screen.
DSC-H5_L2 1-1
1-2. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY

The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.) Note: 1 When replacing the SY-150 board, erase the data in internal memory of the board before replacement. Note: 2 When replacing the SY-150 board or the IC202 on the SY-150 board, execute formatting and initialize the internal memory after replacement.
Method for copying the data in internal memory

Copy
Copies all images in the internal memory to a Memory Stick Duo.
OK Cancel
See the following procedure. Cancels the copying.
1 Insert a Memory Stick Duo having 32 MB or larger capacity. 2 Select [OK] with v on the control button, then press z. The message All data in internal memory will be copied Ready? appears. 3 Select [OK] with v, then press z. Copying starts.
Copying 102_COPY
Use a fully charged Nickel-Metal Hydride battery or the AC Adaptor (not supplied). If you attempt to copy image files using a batteries with little remaining charge, the batteries may run out, causing copying to fail or possibly corrupting the data. You cannot copy individual images. The original images in the internal memory are retained even after copying. To delete the contents of the internal memory, remove the Memory Stick Duo after copying, then execute the [Format] command in (Internal Memory Tool). You cannot select a folder copied on a Memory Stick Duo. Even if you copy data, a (Print order) mark is not copied.
Method for formatting the internal memory

This item does not appear when a Memory Stick Duo is inserted in the camera. The default settings are marked with .
Format
Formats the internal memory.
Note that formatting irrevocably erases all data in the internal memory, including even protected images.
OK Cancel
See the following procedure. Cancels the formatting.
1 Select [OK] with v on the control button, then press z. The message All data in internal memory will be erased Ready? appears. 2 Select [OK] with v, then press z. The format is complete.
PROCESS AFTER FIXING FLASH ERROR

When FLASH error (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed automatically to disabling charge and flash setting. After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.
Method for Initializing the Flash Error Code

Initialize
Initializes the setting to the default setting.
OK Cancel
See the following procedure. Cancels the resetting.
1 Select [OK] with v on the control button, then press z. The message Initialize all settings Ready? appears. 2 Select [OK] with v, then press z. The settings are reset to the default setting.
Make sure that the power is not disconnected during resetting.
DSC-H5_L2 1-2
1-3. PRECAUTION ON REPLACING THE SY-150 BOARD
Ver. 1.1 2006. 06
The Repair Board has already been adjusted. Re-initialization or EVR data copy from the set before repair is not required. Perform VIDEO OUT Default Data Check and Initial Language Data Check mentioned below, and also the adjustment items necessary after SY Board replacement.
1-4. VIDEO OUT DEFAULT DATA CHECK

When you replace to the repairing board, the written data of repairing board also might be changed to original setteing because of broadcast system (NTSC/PAL). When the data has changed because of board replaceing etc., check the default data of VIDEO OUT if destination code is right. If not, rewrite to the right value. VIDEO OUT Default Data Page 4F Address 8D Data NTSC 00 PAL 01
Writing Method: 1) Select page: 00, address: 01, and set data: 01. 2) Select page: 4F, address: 8D, and set data: 00 (NTSC) or data: 01 (PAL). 3) Select page: 40, address: 38, and set data: 00. 4) Click [Save] on the SEUS screen. 5) Select page: 80, address: 34, and check that the data is 00. 6) Select page: 80, address: 30, and check that the data is 00. 7) Select page: 00, address: 01, and set data: 00.
1-5. INITIAL LANGUAGE DATA CHECK

If the SY-150 board was replaced, initial language setting may be changed. Accordingly, change the following data so as to set same initial language as that of the set distributing in each region. Initial language: Language displayed at the next starting if the setting of Setup menu was reset. It is different from the language setting selectable with the menu. Initial Language Data Page Address Data 00 01 04 4F 8C 06 08 0B 0D Language English Japanese Spanish Portugal Simplified Chinese Russian Korean z z z z z z z GP1 GP2 z GP3 z GP4 z
Note: GP1 is fixed to Japanese. GP2 is fixed to English. GP3 is either English, Spanish, or Russian. GP4 is either English, Spanish, Portugal, Simplified Chinese, or Korean. Writing Method: 1) Select page: 00, address: 01 and set data: 01. 2) Select page: 4F, address: 8C, and set the Initial Language Data. 3) Select page: 40, address: 38, and set data: 00. 4) Click [Save] on the SEUS screen. 5) Select page: 80, address: 34, and check that the data is 00. 6) Select page: 80, address: 30, and check that the data is 00. 7) Select page: 00, address: 01, and set data: 00. 8) Turn off the camera. 9) Turn on the camera. Execute Initialize of Setup screen. 10) Check the language displayed when the camera starts.
DSC-H5_L2 1-3E
2. DISASSEMBLY
Link
DISASSEMBLY HELP
COMMON NOTE FOR DISASSEMBLY
DSC-H5_L2
2. DISASSEMBLY
2. DISASSEMBLY
NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. When remove a connector, don't pull at wire of connector. Be in danger of the snapping of a wire.
When installing a connector, don't press down at wire of connector. Be in danger of the snapping of a wire.
Cut and remove the part of gilt which comes off at the point. (Take care that there are some pieces of gilt left inside)
DISCHARGING OF THE FLASHLIGHT POWER SUPPLY CAPACITOR

The charging elect capacitor 320uF (330V) is charged up to the maximum 300 V potential. There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the DSC-H5 is simply turned off. Therefore, the remaining voltage must be discharged as described below.
Discharging the Capacitor

Short circuits between the positive and the negative terminals of charged capacitor with the short jig about 10 seconds.
Short jig (1k/1W)
Preparing the Short Jig

To preparing the short jig. a small clip is attached to each end of a resistor of 1 kW /1 W (1-215-869-11) Wrap insulating tape fully around the leads of the resistor to prevent electrical shock.
ST-142 board
1 k/1 W
Capacitor
Wrap insulating tape.
ST-142
DSC-H5_L2 2-1
2. DISASSEMBLY
The following flow chart shows the disassembly procedure.
2. DISASSEMBLY
2-1. DISASSEMBLY
SW 1 47
8 7 1
5 2
SW 71 4
3 4
3 1
1 Three screws (M1.7x4) 2 Three screws (M1.7x4) 3 Cabinet (rear) section
1 Two claws 2 Flexible board (from the LCD unit) 3 Flexible board
4 Two claws, two dowels 5 Claw, two dowels 6 Two tapping screws (M1.7x3.5) 7 SW-478 flexible board 8 SW-471 board
(from the light guide plate (3.0) block)
Note: Be very careful not to

damage the flexible board.
7 8 1
A (See page 2-4)

-15 0
5 2 4 6
SY
B (See page 2-4)

0
3
2 1 Fuse replacement caution label 3 2 Flexible board (from the lens section) 3 Tape CD retainer (420) 1 Two claws 2 Two tapping screws (M1.7x3.5) 3 LCD frame 4 CD-621 flexible board 5 AF-105 flexible board 6 Flexible board (from the lens section) 7 Control switch block 8 Flexible flat cable (ST-003) 9 From the microphone q; Tapping screw (M1.7x5) qa Main section qa
SY
15
59 66
3 HELP 01 2 1 1 q; q;
7 8 6
SY-150
DSC-H5_L2 2-3
2. DISASSEMBLY
4 1 2 3 3 6
Refer to page 2-1 "DISCHARGING OF THE FLASHLIGHT POWER SUPPLY CAPACITOR, when discharging the capacitor.
7 8
4 5 9
HELP 04
HELP 07
HELP 05
HELP 06
HELP 08
1 Turn the flexible board. 2 Tapping screw (M1.7x5) 3 Lens section
1 Two tapping screws (M1.7x4) 2 Control switch block
1 Tapping screw (M1.7x4) 2 Microphone holder 3 Microphone cushion (B) 4 Microphone 5 Microphone cushion 6 Tapping screw (M1.7x4) 7 AF-105 flexible board 8 Tapping screw (M1.7x4) 9 AF holder
1 Claw 2 Three harnesses (HA-001) (Red, White, Blue) 3 Open the ST cover in the direction of the arrow. 4 ST section
3 1 5 5 4 HELP 03 6 3 3 2 1 6 2
SY
-1
50
HELP 02 2
SY
0 15
4
SM05 3
7 8 1 Flexible flat cable (MS-030) 2 Two tapping screws (M1.7x4) 3 MS-305 board 1 Two claws 2 Flexible board (from the LCD module) 3 EVF section 1 Battery connector 2 From the loudspeaker 3 JK-306 flexible board 4 Two tapping screws (M1.7x4) 5 Flexible flat cable (MS-030) 6 SW-478 flexible board 7 CK-161 flexible board 8 SY-150 board 4 Battery connector 5 Three claws 6 Battery terminal board
DSC-H5_L2 2-4E
HELP
Disassembling and assembling procedures that require attention are described here.
HELP 01
When attaching the fuse replacement caution label to the SY-150 board, cover the harness of the loudspeaker with the fuse replacement caution label.
Fuse replacement caution label
Harnesses of the loudspeaker
HELP 02
When installing the loudspeaker, route the harnesses of the loudspeaker as shown in the figure.
Harnesses of the loudspeaker Loudspeaker (1.0cm)
Bend the harnesses of the loudspeaker at the route of the connector.
HELP 03
When installing the battery terminal board, route the harnesses of the battery terminal board as shown in the figure. The harnesses in the area A must be kept below surface B.
Battery terminal board surface B Harnesses of the battery terminal board
The harnesses in the area C must be kept within the D lines. Bend the harness at portion E so that the harness runs along line F.
Harnesses of the battery terminal board C E F
DSC-H5_L2
HELP
HELP 04
HELP 05
When installing the ST section, route the Harness (HA-004) (Blue) ,Harness (HA-004)(White), and Harness (HA-004) (Red) as shown in the figure.
When installing the ST section, route the Harness (HA-004) (Blue) ,Harness (HA-004)(White), and Harness (HA-004) (Red) as shown in the figure.
Route the harnesses with the ST cover closed.
ST section
Harness (HA-004) (Blue) , Harness (HA-004)(White), Harness (HA-004) (Red) ST section
Harness (HA-004) (Blue)
Harness (HA-004) (White) Harness (HA-004) (Red)
HELP 06 4 1 Harness (H-004) (Red) 5 9 2 Harness (H-004) (White) 3 Harness (H-004) (Blue) 4 Flash unit, ST-144 board q; 5 Apply the soldering in three points. 6 ST-142 board 7 Apply the soldering in three points. 8 ST cover 9 Two claws 2White 3Blue 1Red 8 q; Tapping screw (M1.7x4)
Solder each harness according to the color ( Red, White, Blue) as shown in the figure.
6
Solder each harness according to the color ( Red, White, Blue) as shown in the figure.
ST-144 board
ST-142 board
Blue Red White

7
Blue White
Red
DSC-H5_L2
HELP
HELP 07
Install the microphone tilted as shown in the figure below.
Microphone holder Microphone cushion (B)
Microphone holder Microphone cushion (B) Microphone Microphone cushion
Microphone Microphone cushion
HELP 08
When removing the lens ring, remove the screw and strap sheet metal (R) first. Slide the cap lever in the direction of arrow A while taking care that the cap lever is not caught on the notch of the lens ring. Remove the lens ring by turning it in the direction of arrow B.
Cap lever
1 Tapping screw (M1.7x4) 2 Strap sheet metal (R)
Cap lever Lens ring

A
3 Lens ring
Notch of the lens ring
DSC-H5_L2
HELP
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/2) OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM (2/2)
DSC-H5_L2
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2)
LENS UNIT
IRIS SHUTER
Ver. 1.1 2006. 06
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CD-621 FLEXIBLE BOARD MS-030 FLEXIBLE FLAT CABLE
K5,G4,H4,L5 H2,H1,J1,J2 M5,J4,K4,M6 K2,K1 AC4,AE4 AE5,AC5 AB6,AF6 CN301 4,3,5, 7,2,8 6 4,3,5,7,2,8 CN302 MEMORY STICK Duo CONNECTOR
CD-617 BOARD
SY-150 BOARD (1/2)

22 | 35 MS D0-MS D3, MS BS, MS CLK XMS IN 6 CN706
IC002
CCD IMAGER 15 1 1-14
V1 V2 V3A,B V4 V5A,B V6 V7 V8 V9 V10 VST, VHLD
CA AD0 - CA AD13 X101

12MHz XTAL OSC
4,3,5, 7,2,8
IC001
BUFFER
CCD OUT 20 20 6
S/H A/D CONV.
(3/8)
EXTAL A6
(2/8)
VSUB 1 1 RANDOM TRIGGER 4 CN001 4 CN301 21
27,28 19-17 H1A,B H2A,B RG
24 23
CP301
TIMING GENERATOR 47 45 46 CLK TGO E1 H5 J5 CA HD, CA FD
CSUB
Q001 VSUB 36
IC101 (1/2)
CAMERA DSP
D21,D22,D20,B22,A22,A23 B23,E20,E21,B24,A24,A25 B25,C25,C26,B26,E10,A10 D10,E11,B10,A11,B11,E12 D11,D12,F12,B12,A12,E13 D13,D14 D17,D18,D16,B18,A19 B19,E16,D19,E19,E17 B20,A20 D8,D7,E8 E7,D6,D5 E6,B4
MS-305 BOARD
CN001 2
26-39
12,10,8,6,14
D0-D31
(4/8)
26-39
12,10,8,6,14
2 CN301 1 | 5 7 | 20 40, 41
39
XCS_FE
U22
IC203
A0-A11 256Mbit SDRAM CN707 20 LCD D0-D7 | 13 11 10 12 22 23 24
Q301 VSUB_CONT_POST VSUB 42 XSAN_RST_OUT VSUB_CONT_PRE T4 R23
CK-161 BOARD
CN001 LCD D0-D7 12 | 19 21 22 20 10 9 8 LCD D0-D7 LCD9001 3.0 INCH COLOR LCD PANEL
M
SHUTTER MOTOR
1 4
F2 E2 D2 B1 F3 F4 D6 E6 B7 C6
SAN1 SO,SCK
IRIS MOTOR
IRIS A IRIS XA IRIS B IRIS XB
(1/8)
IC401
(1/2)
IRIS DRIVE SHUTTER DRIVE
F5 E5 D3 F1 G1 E4 D5 A6 B6 C5
DIR2A BRK2A DIR2B BRK2B
DIR2A BRK2A DIR2B BRK2B MSHUT DIR MSHUT EN FC DIR A FC DIR B FC EN ZM DIR A ZM BRK A FC SENS ZM SENS 1ST ZM SENS 2ND
E9 B8 N4 P6 P4 R2 R25 R5 L2 N5 L4 N6 N2 U4 U5 V4 V5 W4 J25 D9
LCD HD LCD VD LCD CK
U2 SAN1 SO, SCK R6 AF4 XSAN RST OUT
SAN1 SO, SCK
M
FOCUS MOTOR
8 5
SHUTTER + SHUTTERFOCUS A FOCUS XA FOCUS B FOCUS XB
MSHUT DIR MSHUT EN
M
ZOOM MOTOR
9 16
FOCUS MOTOR DRIVE
FC DIR A FC DIR B FC EN
XMS IN
CN703 15 | 12 LCD D0-D7 10 | 7 LCD HD LCD VD 18 17 LCD CK 19 SAN1 SO, SCK XSAN RST OUT Y26 XCS_AUDIO E4 F3 E3 E6 6 4 20
M
FOCUS RESET SENSOR ZOOM RESET SENSOR 1ST ZOOM RESET SENSOR 2ND ZOOM DC FG
36 39
ZOOM + ZOOM -
B4 B5
ZOOM MOTOR DRIVE
A2 B2
ZM DIR A ZM BRK A
ZM DC FG 1A ZM DC FG 1B LENS TEMP
LCD9002 COLOR EVF UNIT
22
FC SENS
24
ZM SENS 1ST B4 ZM SENS 2ND ZM DC FG 1A ZM DC FG 1B LENS TEMP CN401 L26 A01-A21 A01-A16 D0-D15 AB13,AA13,AE13,AF13,AF12 AE12,AA12,AC12,AC11,AB12 AE11,AF11,AE10,AB11,AC10 AB10 AF21,AF20,AE20,AB18,AB19 AC19,AB16,AE19,AF19,AF18 AE18,AA15,AC18,AC17,AB15 AE17,AF17,AE16,AB14,AC16 AC15 SAN27M CK0 XBONOBO CPU RESET XCS BONOBO V OUT A4 AF9 AC25 Y23 H26 U25 U23 XAV JACK IN VIDEO AMP ON C1 AUOUT SPEAKER AMP A5 A2 CN601 K26 E5 AU OUT AMP D1 C2 CN651 PITCH + PITCH PITCH HALL+ PITCH HALLYAW+ YAWD0-D15 B1 D1 XSAN RST OUT B5 A2
with in BACK LIGHT
25 32 31 18
(4/8)
(4/8)
IC201
BURST FLASH MEMORY
IC202
ONE NAND FLASH MEMORY
(5/8)
SAN1 SO, SCK AUIN
IC602
CN602 MIC AMP B6 2 1 2
MIC SIG SP+ SP-
LENS TEMP SENSOR
MIC
MIC9001
ACTIVE LENS ACTUATOR PITCH 11 10 7 6 12 13 3 2
SP9001 SPEAKER
A7
(6/8)
H2 J4 B10 D10 J9 J7
D0-D15
H
YAW
IC504
STEADY SHOT CONTROL
A01-A21
3,2 AC1 AD1 USB VBUS USB DPP, USB DMM 9 8
CN001 (USB)
YAW HALL+ YAW HALLCN501
A3 A6 A5
SAN 27M CLK0 XBONOBO CPU RESET XCS BONOBO
6 1 AU LINE OUT J001 A/V OUT 1 4
SE501
(6/8)
PITCH SENSOR
SE502
B4 2 PITCH AD B5 G5 B6 YAW AD
SAN0 SO, SI, SCK
IC506
PITCH/YAW SENSOR AMP 6 14 19
KEY BONO XMS IN
TO OVERALL BLOCK DIAGRAM (2/2)
1
SAN1 SO, SCK
(5/8)
3
YAW SENSOR
12
18
J5
USB V BUS
(PAGE 3-2)
IC601
VIDEO AMP
V LINE OUT 2
V LINE OUT
Q503 BUFFER
C_RESET
D5 D6
JK-306 FLEXIBLE BOARD
DSC-H5_L2 3-1
Ver. 1.1 2006. 06
3-2. OVERALL BLOCK DIAGRAM (2/2)

SY-150 BOARD (2/2)
ST-003 FLEXIBLE FLAT CABLE
1 | 3 1 | 3
ST-142 BOARD
ST-144 BOARD
ST UNREG T101 D102 (RECT) XE H 15
(3/8)
IC101 (2/2)
SYSTEM CONTROL
R22 V23 AB22
STRB CHG XSTRB FULL STRB CHG CONT
7 6 5
7 6 5
10 9 6
HIGH VOLTAGE CHAGER
1 2
C105
L001 TRIGGER COIL FLASH UNIT
IC101
IGBT DRIVE 7
Q101 FLASH DRIVE XE L D001
R4
STRB ON
STRB ON
4 CN101
Q702 D1.2V STRB CONT
CN701
TO OVERALL BLOCK DIAGRAM (1/2)
SAN0 SO, SI, SCK KEY BONO

USB VBUS XMS IN
(1/8)
(PAGE 3-1)
AA25
STRB PLUNGER ON
A1
IC401 (2/2)
STRB PLUNGER DRIVE
CN705 B3 8 7
AF-105 FLEXIBLE BOARD

STRB PLUNGER 3 4 4 3
RY201 PLUNGER
V22 AC23
XSTRB POPUP XLENS COVER SENSE
5 1 XAF LED
XSTRB_POPUP
1 6 CN201
S201 (FLASH POP UP)
S001 (LENS COVER OPEN)
4 BT9001
BATTERY TERMINAL
D001 (AF LED)
PL-045 BOARD
1 2 3 4
UNREG REG GND F001
ST UNREG
CN001
SAN0 SO C5 SAN0 SI C6 XSAN0 SCK B6
SAN0 SO, SI, SCK
SAN0 SO SAN0 SI XSAN0 SCK AB5 AA5 Y5 XCS DD BATT SENS W23 K25 RSTA XDD RST OUT XPWR OFF Y4 R26 AA23
N21 P23
XAE LOCK SW XSHUTTER SW
CN704 9 6
S103 SHUTTER
CONTROL SWITCH BLOCK

S105
(8/8)
XCS DD A6 BATT SENS D4
IC001
UNREG F002
L22 L25 AB23 W22 G25
MODE DIAL 0 MODE DIAL 1 JOG A JOG B
14 12 11 10
MODE DIAL
DC/DC CONVERTER XDD RST OUT A7 REAL TIME CLOCK

XPWR OFF
B7
JOG DIAL S106,101,102 EXEC
KEY AD2 8
FINDER, FOCUS, BRK S108

XPLAY SW
1 XPWR LED A8
X001 32.768KHz OSC I OSC O
PLAY D102 (POWER) S104
A9 B8
VL 3V
BT001 LITHIUM BATTERY (SECONDARY)
EVER SRAM D 3.2V CAM 3.2V A 3.2V MS VCC CAM 2.9V PANEL 2.9V D 1.8V M 5V ST 5V D 1.2V CAM 15V CAM -7.5V
D23
XPWR ON
POWER S107
KEY BONO
STEADY SHOT
C7 C9
XPWR ON USB VBUS
B10 XMS IN
KEY AD0 K23 KEY AD1
CN702 8 26
S401 S406 DOWN, RIGHT, UP, LEFT, SET, DUST S407 S410
D7
XPLAY SW
BL H BL L A4 XAF LED E4 L23
27
ZOOM W, ZOOM T, MENU, DISP
LED9001 LCD BACK LIGHT 6 5 2 1
XACCESS LED
1 30 31 32 33 BL H BL L
33 4 3 2 1 CN401
D401 (ACCESS)
CN402
SW-478 FLEXIBLE BOARD
SW-471 BOARD
DSC-H5_L2 3-2
3-3. POWER BLOCK DIAGRAM (1/2)

SY-150 BOARD (1/2)
BT9001
BATTERY TERMINAL
ST-003 FLEXIBLE FLAT CABLE

ST UNREG ST UNREG
ST-142 BOARD
T101 1 | 3 7 6 5 8 CN101
15
1 2
UNREG
F001
1 | 3 7 6 5 8
D102(RECT)
XE H
FLASH UNIT
STRB CHG 3 REG GND 4 CN001 XSTRB FULL STRB CHG CONT
L101
10 9 6
IC101
HIGH VOLTAGE CHAGER IGBT DRIVE
1 2
C105
ST 5V
CN701
F002
ST-144 BOARD
MS VCC
UNREG
ST UNREG
(5/8) (8/8)
AU 3.0V PWR1-1 A1 PWR1-2 B1 PWR1-3 C2 VO1-1 F1 VO1-2 F2 VFB1 H2 MS PWR IN MS PWR LDO3IN 2.9V REG LDO3
K25 Y4 R26 AA23 T25
AU 3.0V ST 5V CAM 3.2V D 3.2V A 3.2V L601
MS-305 BOARD
CN302 MEMORY STICK Duo CONNECTOR 9 CN301 MS VCC 10 10 CN706
R002
IC001
DC/DC CONVERTER REAL TIME CLOCK J1 UNREG1-1,2 K1 EVER SRAM
D001
ST 5V CAM 3.2V D 3.2V L001 L011 A 3.2V
IC602
MIC AMP SPEAKER AMP AU OUT AMP
H1
LDO1
3.1V REG.
G1
(5/8)
4 1
VL 3V
MS-030 FLEXIBLE FLAT CABLE
B8 RTC BAT
A8 OSC I
MS VCC
G2
IC603
3
AU 3.0V
3V REG
R22 V23 AB22
X001 32.768KHz
B2
(3/8)
A9 OSC O
CAM 2.9V
A2
CAM 2.9V
IC101
CAMERA DSP SYSTEM CONTROL
BATT SENS XDD RST OUT XPWR OFF MS PWR ON
D4 DTG1 A7 XRESET B7 XPWR OFF MS PWR ON D3
LDO2IN 1.8V REG LDO2
PANEL 2.9V
B3
D 1.8V
A3
UNREG2
XCS DD SAN0 SO SAN0 SI XSAN0 SCK
W23 AB5 AA5 Y5
XCS DD C5 SAN0 SO C6 SAN0 SI B6 XSAN0 SCK

A6
J6 K6
PWR56 OUT J7 K7 LX5-1 LX5-2 LX5-3 LX5-4

J9 J10 K9 K10
L006 CAM 15V D003 (RECT) Q004 SWITCHING & RECT CAM -7.5V
D102 (POWER)
D23
XPWR LED
VFB5 H9
D 3.2V 4 D 3.2V A 3.2V AU 3.0V VI 3.2V D 1.2V 13 D 1.8V SD 1.8V
TO POWER BLOCK DIAGRAM (2/2)
GT6 H6 VFB6 H7
L009 M 5V
(PAGE 3-4)
PWR2
D10
L003 LX2 C10 VFB2 D8

C7 XPWRON1
F003
MODE DIAL
A 3.2V
D 1.2V ST UNREG L005
S104 POWER S108 PLAY XPLAY SW

1 CN704
XPWR ON
XPWR ON
3
XPLAY SW
LX3
D7 XPWRON2
E10
BL H D002 (RECT) BL L
BL H
L201
VO3 E9
(4/8) (4/8)
LV3 RS3
F9 F8
BL L
IC203
256Mbit SDRAM
IC202
ONE NAND FLASH MEMORY
D 3.2V
L008 Q001 SWITCHING BG4 G9
Q003 SWITCH M 5V ST 5V ST 5V PANEL 8.5V ON
(4/8)

D3.2V 3
D 1.8V
IC201
BURST FLASH MEMORY
A4
TG4
F10
VFB4 F7 PSG4 G8
XAF LED
Q002 RECT
MT 5V ON PANEL 2.9V
D001 (AF LED)
XAF LED
4 CN705
PORTB C4 PORTA B4
PANEL 8.5V ON MT 5V ON CAM 3.2V VI 3.2V D601 L602
(5/8)
IC601
VIDEO AMP
D 3.2V A 3.2V, AU 3.0V, VI 3.2V, D 1.8V, D 1.2V
DSC-H5_L2 3-3
Ver. 1.1 2006. 06
3-4. POWER BLOCK DIAGRAM (2/2)
SY-150 BOARD (2/2)

CAM 3.2V D 3.2V A 3.2V CAM 2.9V ST 5V
4 1
L303 L302
FB308
HDVDD TG 3V DRVDD FE 3V TCVDD RGVDD
(2/8)
(2/8)
L304
CP301
S/H A/D CONV. TIMING GENERATOR
CD-621 FLEXIBLE BOARD
CD-617 BOARD
IC001
BUFFER
IC301
3
3.3V REG
FB302 FB301
CAM 15V CAM -7.5V
L301
CAM 15V CD CAM -7.5V CD CN301

22 18 22 18
IC002
CCD IMAGER CN001
D 3.2V
D 3.2V
(1/8)
A 3.2V M 5V
21
FC RST VCC
IC401
IRIS DRIVE SHUTTER DRIVE FOCUS MOTOR DRIVE ZOOM MOTOR DRIVE PLUNGER DRIVE
27 28
FOCUS RESET SENSOR
LENS UNIT
ZM RST VCC
ZOOM RESET SENSOR
ZM FG VCC
33
(6/8)
L503
C542 D501 (RECT)
ZOOM DC FG
CN401 PANEL 8.5V

4
IC507
6
8.5V REG
9 SW D502 (RECT) 1
PANEL 8.5V 0N
1
TO POWER BLOCK DIAGRAM (1/2)
ST UNREG Q504 ST 5V M 5V ON
6 8
VBAT PS
(6/8)
VOUT 2
5V
IC501
DC/DC CONV.
(6/8)
EN
IC506
PITCH/YAW SENSOR AMP 2.9V
3
SE501, 502
PITCH/YAW SENSOR
(PAGE 3-3)
(6/8)
A 3.2V
4
IC503
2.9V REG
1
CN707
L703
CK-161 BOARD
27 26
PDD VSSG VDD2
5 6 28
L705
LCD9001 3.0 INCH COLOR LCD PANEL
ST 5V
ST 5V
L704
VDD1 CN001
29
DISCHARGE D 3.2V
6
D401 D 3.2V
28 ACCESS LED
BL H BL L CN702
B9
30 31 32 33
BL H BL L
4 3 2 1 CN401
6 5 2 1
CN402
LED9001 LCD BACK LIGHT
(6/8)
D3.2V ST 5V
4 1
(6/8)
IC505
3
IC504
1.5V STEADY SHOT CONTROL
SW-471 BOARD
1.5V REG
PANEL 8.5V 0N M 5V ON PANEL 2.9V L701

4 1
(7/8)
IC701
3
2.5V
22
2.5V REG 5.0V L702

1
LCD9002 COLOR EVF UNIT
ST 5V
LED 5V CN703
11
EVF BACK LIGHT
DSC-H5_L2 3-4E
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM
MS-305 BOARD (SIDE B) CD-617 BOARD (A SIDE) CD-617 BOARD (B SIDE)
39 1 39 38

S001 (LENS COVER OPEN)
2 1 3
CN001
1 2 10 1
IC002
S201 (FLASH POP UP)

2 1
RY201 (PLUNGER)
12
MS-030 FLEXIBLE FLAT CABLE

CN301
39 1
CN201
6 1
PL-045 BOARD (SIDE A)

BT9001 BATTERY TERMINAL
PL-045 BOARD (SIDE B)
4 6
3 1
MS-305 BOARD (SIDE A)
D001 AF LED
10
SW-471 BOARD (SIDE B)
MIC9001 MICROPHONE
LCD9002
LEVEL3 SY-150 BOARD (SIDE B)

21
COLOR EVF UNIT
LEVEL3 SY-150 BOARD (SIDE A)

CN705
CN302 MEMORY STICK Duo CONNECTOR
CN001
4 1
38
CN301
CN706
F003
F002
F001
CN704
CN602
22
CN703
10 1 39 1
14
CONTROL SWITCH BLOCK ST-003 FLEXIBLE FLAT CABLE
12
12 1

1 33 32 33 1
CN651
CN702
14
CN701
33 32
33
2 2 1
CN401
38 39
CN601
1 2
CN707
28 29
14
ST-142 BOARD (SIDE A)

FLASH UNIT
CN401
CN501
12
SW-471 BOARD (SIDE A)

1 29 LND006
LND004 LND005
J001 A/V OUT JACK LCD9001
J001
4 2
LND003
SP9001 SPEAKER
LND002 LND001
3 1
ST-144 BOARD
1
3.0 INCH COLOR LCD MONITOR
CN001 USB CONNECTOR
CN001
2 5 1
LND101 14
LED9001
31 30
CN001
1 2
LND103
LND102
CN402
CK-161 FLEXIBLE BOARD

BACKLIGHT
JK-306 FLEXIBLE BOARD LENS BLOCK
C105
ST-142 BOARD (SIDE B)

1 2
DSC-H5_L2 4-1
FRAME SCHEMATIC DIAGRAM
CN101
4-2. SCHEMATIC DIAGRAMS

Link
CD-617 BOARD (CCD IMAGER) SW-471 BOARD
(LCD BACK LIGHT, FUNCTION SWITCH)

(MODE/JOG DIAL, FUNCTION SW)

(AF LED, LENS COVER SW)
CK-161 BOARD (LCD PANEL) ST-142 BOARD (FLASH DRIVE) ST-144 BOARD (FLASH) MS-305 BOARD (MEMORY STICK) PL-045 BOARD (PLUNGER)
JK-306 FLEXIBLE BOARD (AV/USB JACK) CD-621 FLEXIBLE BOARD (SY-CD RELAY) SW-478 FLEXIBLE BOARD (SY-SW RELAY) MS-030 FLEXIBLE FLAT CABLE (SY-MS RELAY) ST-003 FLEXIBLE FLAT CABLE (SY-ST RELAY)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
DSC-H5_L2

THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)
(For schematic diagrams) All capacitors are in F unless otherwise noted. pF : Link V or less are not indicated except for electrolytics F. 50 and tantalums. Chip resistors are 1/10 W unless otherwise noted. k=1000 , M=1000 k. Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520 Kinds of capacitor Temperature characteristics External dimensions (mm) Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. Parts with * differ according to the model/destination. Refer to the mount table for each function. All variable and adjustable resistors have characteristic curve B, unless otherwise noted. Signal name XEDIT EDIT PB/XREC PB/REC 2: non flammable resistor 5: fusible resistor C: panel designation A: B+ Line B: B Line J : IN/OUT direction of (+,) B LINE. C: adjustment for repair. (Measuring conditions voltage) Voltages are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values. (VOM of DC 10 M input impedance is used) Voltage values change depending upon input impedance of VOM used.) 1. Connection
Pattern box
Pattern box PTB-450 J-6082-200-A or Small pattern box PTB-1450 J-6082-557-A
Color bar chart

For PTB-450: J-6020-250-A For PTB-1450: J-6082-559-A
L = 1 m (PTB-450) L = 40 cm (PTB-1450) Pattern box L Front of the lens Camera
2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain.
Yellow
H
Cyan Green
White Magenta
A B
A=B
Fig. a (Video output terminal output waveform)
Red Blue
B A Electronic beam scanning frame CRT picture frame
Fig.b (Picture on monitor TV)
Precautions for Replacement of imager

If the imager has been replaced, carry out all the adjustments for the camera section. As the imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light. When indicating parts by reference number, please include the board name.
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note : Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.
DSC-H5_L2 4-3
1 CD-617 BOARD
CCD IMAGER
XX MARK:NO MOUNT
3
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
10
CN001
39P V4 V10 VST V3B V1 39 38 37 CL007
14 13 12 11 10 36
VHLD
VST H1A
V5B
V5A
V3B
V3A
V10
V9
V8
V7
V6
V4
V2
35 34 33 32 CCD IMAGER
V3A V6 V2 V8 VHLD V7 V5B V9
IC002
GND VDD H1B H2B RG
IC002 ICX629BQF-13
CSUB
30 29 28
GND
GND
SUB
N.C.
15 16 17 18 19 20 21 22 23 24 25 26 27 28 27
R9.1 P0 R12.7 P0 R7.7 P0 R2.1 P0 R1.1 P0
C
TO CD-621 FLEXIBLE BOARD
V5A REG_GND REG_GND REG_GND CAM_15V_CD REG_GND CCD_OUT REG_GND
26 25 24 23 22 21 20 19 18 R9.1 P0 R001 0
IC001
BUFFER
C005 0.1u 16V
(PAGE 4-12)
C002 0.1u
IN VCC GND OUT IDRV IC001 CXA3691EN-T9
ISF
R5.0 P0 R12.7 P0 R4.3 P0
R010 100K
C004 0.1u 16V
CAM_-7.5V_CD REG_GND REG_GND REG_GND RG REG_GND H1A REG_GND
17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 2 R002 0 0 3 1 R8.8 P0 Q001 DTC144EMT2L VSUB R003 270k R004 1M C001 XX
R007 150k C008 XX C009 0.1u
R011 0
R9.1 P0
C003 XX R009 XX
H1B REG_GND H2B REG_GND H2A REG_GND RAMDOM_TRIGGER REG_GND
CSUB VSUB
DSC-H5_L2 4-5
C006 0.1u 16V B
R-7.5 P0 R2.1 P0 R1.1 P0

C007 0.1u 16V B
R9.1 P-0.2 R9.5 P0
H2A
Note: IC002 is not included in this COMPLETE of CD-617 board.
CCD_OUT
31
VL
V1
R-6.0 P0 R-0.7 P0 R-0.7 P0 R-0.7 CL008 P0 R-0.7 P0 R-0.7 CL002 P0 R-0.7 CL003 P0 R-0.7 P0 R-0.7 P0 R-0.7 CL001 P0 R-7.2 P0 R-6.0 P0 R-5.4 P0 R-6.0 CL006 P0
9 8 7 6 5 4 3 2 1
CD-617
1 SW-471 BOARD A
10
LCD BACK LIGHT, FUNCTION SWITCH

XX MARK:NO MOUNT
RB402 2200x4 33 32 31 30 29 28 27 26 25 24 23 22 1 S404 UP 2 S410 MENU 1 RB401 2200x4 D402 MAZW068H0LS0 2 R405 5600 1005 R401 330 1 D401 SML-310LTT86 (ACCESS) 4 5 S407 ZOOM T S409 ZOOM W
CN401
33P XACCESS_LED REG_GND REG_GND
NO 2 3 6
1 4 5
NO 2 3 6
NC REG_GND D_3.2V KEY_AD1 KEY_AD0 REG_GND NC NC
C
TO SW-478 FLEXIBLE BOARD
NC NC NC NC REG_GND REG_GND NC REG_GND
21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 6 5 4 3 2 1 CN402 BL_H BL_H NC NC BL_L BL_L LCD BACK LIGHT 6P LED9001 LND401 STATIC_GND D403 MA2S111-(K8).SO
(PAGE 4-12)
REG_GND NC NC REG_GND NC NC REG_GND NC
S406 LEFT 1 2 1 2
R403 5600 S405 SET 1 2 1 3 S401 RIGHT 4
S408 DISP 2
R404 27k
4 R402 27k
NC NC BL_H BL_H BL_L BL_L
1 S402 DUST 3 1 2
S403 DOWN
DSC-H5_L2 4-6
SW-471
1
LCD PANEL
XX MARK:NO MOUNT
29P
CK-161 FLEXIBLE BOARD A

LCD9001 (LCD UNIT)
CN001 GND GND VCC1 VCC2 4.2VADJ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008 LND009 LND010 LND011 LND012 LND013 LND014 LND015 LND016 LND017 LND018 LND019 LND020 LND021 LND022 LND023 LND024 LND025 LND026 LND027 LND028 LND029 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 GND GND VCC1 VCC2 4.2VADJ VBRT COMAC
31 P
VBRT COMAC COMDC(H) COMDC(L) VD HD DCK TO SY-150 BOARD(7/8) CN707
COMDC(H) COMDC(L) VD HD DCK D7 D6 D5 D4 D3 D2 D1 D0 XCS SI SCLK RESET POFF VSSG PVDD GND COM N.C. N.C. 3.0 INCH COLOR LCD PANEL
D7 D6 D5 D4 D3 D2 D1 D0 XCS
(PAGE 4-20 of LEVEL 3)
SI SCLK RESET POFF VSSG PVDD GND COM
DSC-H5_L2 4-7
CK-161
Refer to page 4-3 for mark 0.
2 ST-142 BOARD
FLASH DRIVE
XX MARK:NO MOUNT
CN101 12P ST_UNREG ST_UNREG ST_UNREG 1 2 3 4 5 6 7 8 9 10 11 12
4
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
10
T101 CONVERTER TRANSFORMER
L101 4.7uH C101 22u 6.3V C102 22u 6.3V C106 22u 6.3V CL101
5 2 1
3 D102 CRF02(TE85R) 4
LND101 1 XE_H
TO ST-003 FLEXIBLE FLAT CABLE
STRB_ON STRB_CHG_CONT XSTRB_FULL STRB_CHG ST_5V REG_GND REG_GND REG_GND REG_GND
(PAGE 4-13)
C105 320u 330V
Note: C105 is not included in this COMPLETE of ST-142 board.
C
HGND VBATT N.C
R2.4/P2.6 17 16 15 14 13
TO ST-144 BOARD
(PAGE 4-9)
N.C
R2.4/P2.6
SW SW VCC F_ON
IC101 TPS65552RGTR
D101 MAZS068008SO
N.C
N.C
R102 XX
C103 1u B
G_IGBT
I_PEAK
5.0
PGND CHG XFULL
10 11 12
R2.4/P2.6
N.C
IC101
HIGH VOLTAGE CHARGE, IGBT DRIVE
PGND
0 3.2
LND102 2 REG_GND
Q101 GT8G133 (T2LSONY.Q) FLASH DRIVE 283 LND103 3 XE_L 1 2 0 R103 4.7M C104 XX R104 33 3 4 5 6 7 8
DSC-H5_L2 4-8
ST-142
1 ST-144 BOARD A
FLASH
XX MARK:NO MOUNT
1 PL-045 BOARD A
PLUNGER
XX MARK:NO MOUNT
CN201
Note: RY201 is not included in this COMPLETE of PL-045 board.
6P 1 2 3 4 5 6
LND001 XE_H 1
LND005 XE_+
D202 1SS355TE-17
D203 MAZW068H0LS0 2 RY201 (PLUNGER)
REG_GND TO AF-105 FLEXIBLE BOARD REG_GND STRB_PLUNGER STRB_PLUNGER REG_GND XSTRB_POPUP
C201 1u
R001 1M
B
TO ST-142 BOARD
C002 0.047u 250V
L001 TRIGGER COIL 1 3 LND004 TRIGGER FLASH UNIT
(PAGE 4-11)
S201 (FLASH POP UP)
(PAGE 4-8)
LND002 XE_L 2
C003 0.01u 250V
LND006 XE_D001 RR255L-400TE25 R002 100k
C
LND003 REG_GND 3
1 MS-305 BOARD A
MEMORY STICK
XX MARK:NO MOUNT
CN301 12P REG_GND MS_BS MS_D1 1 2 3 4 5 6 FB304 MS_D3 MS_SCLK REG_GND MS_VCC REG_GND 7 8 9 10 11 12 C301 22u 6.3V C302 0.1u B R304 82 FB306 0uH 7 0 8 9 10 MS_D3 R302 1k R303 82 FB305 FB301 FB302 FB303 0 0uH 0uH 0uH 1 2 3 4 5 6
10P REG_GND MS_BS MS_D1 MS_D0 MS_D2 XMS_IN CN302 MEMORY STICK Duo CONNECTOR
TO MS-030 FLEXIBLE FLAT CABLE
MS_D0 MS_D2 XMS_IN
(PAGE 4-13)
MS_SCLK MS_VCC REG_GND
REG_GND
LND302
STATIC_GND
DSC-H5_L2 4-9
ST-144/MS-305/PL-045
CONTROL SWITCH BLOCK A

MODE/JOG DIAL, FUNCTION SW
XX MARK:NO MOUNT
(MODE DIAL) S101 FOCUS 2 1 S102 BRK 2 1 3 R104 2k R105 2k R106 2k R107 2k 5 4 3 2 1 8 6 7 13 12 11 10 9 R117 2k R118 2k R115 2k R116 2k R109 2k R111 2k R112 2k S107 S106 FINDER 2 4 1 3 2 1 STEADY SHOT
R101 4900
R110 2k R108 10k R103 2200
R114 2k
R102 9300
S103 SHUTTER S105 3 4 1 2 S104 POWER 3 1 JOG DIAL
D
S108 PLAY 1 3 D102 2 4 POWER
E
LND101 LND102 LND103 LND104 LND105 LND106 LND107 LND108 LND109 LND110 LND111 LND112 LND113 LND114
CONTROL SWITCH BLOCK is replaced as a block. So that this PRINTED WIRING BOARD is omitted.
XSHUTTER_SW
MODE_DIAL1
XPLAY_SW
14P
10
11
12
13
TO SY-150 BOARD(7/8) CN704
DSC-H5_L2 4-10
14
MODE_DIAL0
XPWR_LED
KEY_BONO
XPWR_ON
REG_GND
KEY_AD2
XAE_LOCK_SW
D_3.2V
A_3.2V
JOG_B
JOG_A
MODE DIAL
Ver. 1.1 2006. 06
AF-105 FLEXIBLE BOARD A

AF LED,LENS COVER SW
XX MARK:NO MOUNT
S001 (LENS COVER OPEN) 10P 1 2 3 TO SY-150 BOARD (7/8) CN705 4 5 6 7 8 9 10 XLENS_COVER_SENSE LND002 REG_GND LND003 D_3.2V LND004 XAF_LED LND005 XSTRB_POPUP LND006 REG_GND LND007 STRB_PLUNGER LND008 STRB_PLUNGER LND009 REG_GND LND010 REG_GND LND016 LND015 LND014 LND013 LND012 LND011 LND001 1 2 3 D001 DOR5073 (AF LED) 6 5 4
Note: D001 (AF LED) is not supplied, but this is included in AF-105 flexible board complete.
6P XSTRB_POPUP REG_GND STRB_PLUNGER STRB_PLUNGER REG_GND REG_GND 1 2 3 4 5 6 TO PL-045 BOARD CN201
(PAGE 4-9)
1
AV/USB JACK
XX MARK:NO MOUNT
14P
JK-306 FLEXIBLE BOARD A
LND001 XAV_JACK_IN V_LINE_OUT AU_LINE_OUT GND 1 LND002 2 LND003 3 LND004 4 LND005 5 LND006 VCC GND DD+ GND GND NC 6 LND007 7 LND008 8 LND009 9 LND010 10 LND011 11 LND012 12 LND013 13 LND014 STATIC_GND 14 STATIC_GND 1 VCC 2 D3 D+ 4 ID 5 GND CN001 5P NC
3 1 2 4
J001 A/V OUT
TO SY-150 BOARD (5/8) CN651
(USB)
LND015 STATIC_GND
DSC-H5_L2 4-11
AF-105/JK-306
1
SY-CD RELAY
XX MARK:NO MOUNT
39P
1
SY-SW RELAY
XX MARK:NO MOUNT
33P
CD-621 FLEXIBLE BOARD A

A
39P V4 V10 VST V3B 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 V4
33P BL_L BL_L 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 BL_L BL_L BL_H BL_H NC NC NC REG_GND NC NC REG_GND NC NC REG_GND REG_GND NC REG_GND REG_GND NC NC NC NC NC NC REG_GND KEY_AD0 KEY_AD1 D_3.2V REG_GND NC REG_GND REG_GND XACCESS_LED TO SW-471 BOARD CN401
V10
BL_H
VST
BL_H
V3B V1 V3A
NC
V1 V3A V6 V2 V8 VHLD V7 V5B
NC NC
V6
REG_GND
V2
NC
V8
NC
VHLD
REG_GND
V7
NC
V5B V9 V5A REG_GND REG_GND REG_GND CAM_15V_CD REG_GND CCD_OUT REG_GND CAM_-7.5V_CD
NC
V9 V5A REG_GND REG_GND TO SY-150 BOARD(2/8) CN301 REG_GND CAM_15V_CD REG_GND CCD_OUT REG_GND CAM_-7.5V_CD REG_GND REG_GND REG_GND RG REG_GND H1A
C
NC REG_GND REG_GND NC REG_GND REG_GND NC NC
TO CD-617 BOARD CN001
(PAGE 4-6)
(PAGE 4-5)
NC NC
REG_GND
NC
REG_GND
REG_GND
REG_GND
KEY_AD0
RG
KEY_AD1
REG_GND
D_3.2V
H1A REG_GND H1B

REG_GND
REG_GND H1B REG_GND H2B REG_GND H2A REG_GND RANDOM_TRIGGER
REG_GND NC
REG_GND
REG_GND
H2B
XACCESS_LED
REG_GND H2A REG_GND RANDOM_TRIGGER REG_GND CSUB VSUB
REG_GND CSUB VSUB
DSC-H5_L2 4-12
CD-621/SW-478
1
SY-MS RELAY
1
SY-ST RELAY
XX MARK:NO MOUNT
12P
MS-030 FLEXIBLE FLAT CABLE A

XX MARK:NO MOUNT
12P REG_GND MS_BS MS_D1 MS_D0 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12 12P REG_GND MS_BS MS_D1 MS_D0 MS_D2 XMS_IN MS_D3 MS_SCLK REG_GND MS_VCC REG_GND REG_GND TO MS-305 BOARD CN301
ST-003 FLEXIBLE FLAT CABLE A
12P REG_GND REG_GND REG_GND REG_GND 12 11 10 9 8 7 6 5 4 3 2 1 12 11 10 9 8 7 6 5 4 3 2 1 REG_GND REG_GND REG_GND REG_GND ST_5V STRB_CHG XSTRB_FULL STRB_CHG_CONT STRB_ON ST_UNREG ST_UNREG ST_UNREG TO ST-142 BOARD CN101
MS_D2 XMS_IN MS_D3 MS_SCLK REG_GND MS_VCC REG_GND REG_GND
ST_5V STRB_CHG XSTRB_FULL STRB_CHG_CONT STRB_ON ST_UNREG ST_UNREG ST_UNREG
(PAGE 4-9)
(PAGE 4-8)
MS-030 FLEXIBLE FLAT CABLE is replaced as a block. So that this PRINTED WIRING BOARD is omitted.
ST-003 FLEXIBLE FLAT CABLE is replaced as a block. So that this PRINTED WIRING BOARD is omitted.
Schematic diagram of the SY-150 board and CH-199 board are not shown. Pages from 4-14 to 4-22 are not shown.
DSC-H5_L2 4-13
MS-030/ST-003
4-3. PRINTED WIRING BOARDS

Link
CD-617 BOARD SW-471 BOARD ST-142 BOARD ST-144 BOARD MS-305 BOARD PL-045 BOARD AF-105 FLEXIBLE BOARD JK-306 FLEXIBLE BOARD CD-621 FLEXIBLE BOARD SW-478 FLEXIBLE BOARD CK-161 FLEXIBLE BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
DSC-H5_L2

THIS NOTE IS COMMON FOR WIRING BOARDS (In addition to this, the necessary note is printed in each block)
(For printed wiring boards) : Uses unleaded solder. : Pattern from the side which enables seeing. (The other layers patterns are not indicated) Through hole is omitted. There are a few cases that the part printed on diagram isnt mounted in this model. C: panel designation
Chip parts. Transistor

C
6 5 4 4 5 6 5
4 4
Diode
3
1 23
1 2 3 3 2 1 1 2 3 3 2 1 1 2 2 1 3 4
2 1
1 2 2 3
1 2 4 4
1 6 54 3 3 4
5 4 3 3 4 5 2
4 5
3 2 4
1 1 2 4 3
3 1
DSC-H5_L2 4-23

CD-617 (4 layers), SW-471 (4 layers) : Uses unleaded solder.
CD-617 BOARD(SIDE A)
CD-617 BOARD(SIDE B)
Note:IC002 is not included in this COMPLETE of CD-617 board
A
28 15
C005
C002
R010
C003
R011
IC002
C008
R001
B
1 14
2 1
C007
IC001
R007 C009
R009
C004
R003 R004 C001
1-869-215CL002 CL003
CL001
R002
CN001
38 39 2
1 3
C006
11
1-869-215-
11
Q001
CL007 CL008 CL006
SW-471 BOARD(SIDE A)
A
2 5 1 4 6 3
SW-471 BOARD(SIDE B)
4 2 1 3 1 3
R404
R405
1-869 -214SW-471
D403 D402 1
2 3
ZOOM T
1
RB402 1
7
S404 UP
1 1 2 2 1 2
S403 DOWN
R402 R403
CN402
S409 ZOOM W
>EP GW<
S406 LEFT
2 4
S402 DUST
3 1
2 1
LND401
S407
S408 DISP
S401 RIGHT
2 4
S410 MENU
K S405 SET
D401
(ACCESS)
R401
RB401
1 2
CN401
32 33
C
1-869-214-
1-869-214-
11
DSC-H5_L2 4-25
CD-617/SW-471
ST-142 (2 layers), ST-144 (1 layer), MS-305 (4 layers)
: Uses unleaded solder.
ST-142 BOARD(SIDE A)
L101
ST-142 BOARD(SIDE B)
3 2
A
LND101 LND103 LND102
C101
C102
T101
C103 CL101
1 4 R103
Q101
R104 5 4
8 9
1 17
16 13
C106 R102 A K
12
IC101
D102
1 C105
D101 C104
B
ST-142 1-869-218-
12
CN101
1-869-218-
11
LND302
ST-144 BOARD
D001
LND002 LND001 R001
ST144 >PI<
MS-305 BOARD(SIDE A)
11
R304
R002
FB305 FB301 FB302 FB303 R302 FB304 FB306
MEMORY STICK Duo CONNECTOR

10
LND006
L001
12
LND004
1-869-225-
11
C302
LND005
1-869-216-
11
DSC-H5_L2 4-26
+ P
CN302
C301
R303
C002
C003 LND003
ST142-
>EP GW<
1-869-218-
11
MS-305 BOARD(SIDE B)
CN301
12 1
MS-305 >EP 1-869-216GW<
1-869-21611
ST-142/ST-144/MS-305
Ver. 1.1 2006. 06

PL-045 (2 layers), AF-105 FLEXIBLE (1 layer), JK-306 FLEXIBLE (1 layer) : Uses unleaded solder.
PL-045 BOARD (SIDE A)
PL-045 BOARD (SIDE B)

1 6
CN201
2 3
S201 1 2 RY201
(FLASH POP UP)

1
(PLUNGER)
D203
C201
PL045
1-869-217-
11
Note: RY201 is not included in this COMPLETE of PL-045 board.

LND011 LND012 LND013 LND014 LND015 LND016
D001 10
AF LED
6 4
LND010 LND009 LND008 LND007 LND006 LND005 LND004 LND003 LND002
(LENS COVER OPEN)

2 1 3 1
AF-105
1-869-223-
>PI<
Note: D001 (AF LED) is not supplied, but this is included in AF-105 flexible board complete.
DSC-H5_L2 4-27
>EP GW<
D202
1-869-217-
11
JK-306 FLEXIBLE BOARD

4 2 J001 3 1 A/V OUT
>PI<
1 CN001 1
S001
2 (USB) 5
14
FX
JK-3061-869-224-
1-869-223-
11
11
PL-045/AF-105/JK-306
CD-621 FLEXIBLE (2 layers), SW-478 FLEXIBLE (1 layer), CK-161 FLEXIBLE (2 layer)
: Uses unleaded solder.

1 1
39
1-869-222- 39 11

33 1
CK-161 FLEXIBLE BOARD

2 1 CN001 30 31
FX
SW-478-
>PI<
1-869-22629
1-869-227LND029 LND028 LND027 LND026 LND025 LND024 LND023 LND022 LND021 LND020 LND019 LND018 LND017 LND016 LND015 LND014 LND013 LND012 LND011 LND010 LND009 LND008 LND007 LND006 LND005 LND004 LND003 LND002 LND001
11
SY
11
1 33
Printed wiring board of the SY-150 board and CH-199 board are not shown. Pages from 4-29 to 4-31 are not shown.
DSC-H5_L2 4-28
CD-621/SW-478/CK-161
4-4. MOUNTED PARTS LOCATION

CD-617 BOARD
* * * * * * * * * * * * * * * C001 C002 C003 C004 C005 C006 C007 C008 C009 CL001 CL002 CL003 CL006 CL007 CL008 B-2 B-1 B-1 B-1 B-1 B-2 B-1 B-2 B-2 B-3 B-3 B-3 B-3 B-3 B-3
no mark : side A * mark : side B ST-142 BOARD

C101 C102 C103 C104 * C105 C106 CL101 A-2 A-2 A-2 B-2 B-3 B-3 A-2
SW-471 BOARD
* CN401 C-5 CN402 B-2 D401 * D402 * D403 B-6 B-6 B-5
* LND401 B-6 * R401 * R402 * R403 R404 R405 B-5 B-5 B-5 A-2 B-2
CN101 B-3 D101 D102 IC101 B-2 B-3 B-3 A-1
* RB401 B-5 RB402 B-2 S401 S402 S403 S404 S405 S406 S407 S408 S409 S410 A-4 C-5 B-5 B-3 B-4 C-4 B-1 B-2 C-1 B-3
L101
* CN001 B-1 * IC001 IC002 * Q001 * * * * * * * * R001 R002 R003 R004 R007 R009 R010 R011 B-1 B-2 B-2 B-2 B-2 B-2 B-2 B-2 B-2 B-2 B-1 LND101 A-1 LND102 A-2 LND103 A-1 Q101 R102 R103 R104 T101 B-1 B-3 B-2 B-2 A-3
Mounted parts location of the SY-150 board is not shown. Page 4-33 is not shown.
DSC-H5_L2 4-32E
CD-617/SW-471/ST-142
NOTE
5. REPAIR PARTS LIST

NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
Link
EXPLODED VIEWS
J I G B
OVERALL SECTION
LCD SECTION
MAIN SECTION
LENS SECTION
H C E
CABINET (FRONT) SECTION
ST SECTION
Link
AF-105 FLEXIBLE BOARD CD-617 BOARD CK-161 FLEXIBLE BOARD JK-306 FLEXIBLE BOARD
ELECTRICAL PARTS LIST

A D G J
ACCESSORIES
C F I
MS-305 BOARD PL-045 BOARD ST-142 BOARD
B E H
ST-144 BOARD SW-471 BOARD SY-150 BOARD
DSC-H5_L2
NOTE: -XX, -X mean standardized parts, so they may have some differences from the original one. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The mechanical parts with no reference number in the exploded views are not supplied. Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. CAPACITORS: uF: F COILS uH: H RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable SEMICONDUCTORS In each case, u: , for example: uA...: A... , uPA... , PA... , uPB... , PB... , uPC... , PC... , uPD..., PD...
When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.
Language that can be selected about SY-150 board
Arabic Dutch Russian Swedish Korean Norwegian Danish Finnish Polish Hungarian Czech Persian
z z z z z z z z z z z
Portugal Simplified Chinese Traditional Chinese
Japanese English French
German Spanish
Italian
Area
GP1
GP2
z J US CND z z AUS Vietnam AEP UK E JE HK CH KR BR
z z
GP3
z z z z z z
GP4
z z
Abbreviation J : Japanese model CND : Canadian model AUS : Australian model JE : Tourist model HK : Hong Kong model CH : Chinese model KR : Korea model BR : Brazilian model
DSC-H5_L2 5-1
Thai
5-1. EXPLODED VIEWS

5-1-1. OVERALL SECTION
ns : not supplied
3 2
SW 1 47
3 4 8 1
ns
LCD section (See page 5-4)
5 3
3 6
Ref. No. 1 2 2 3 3 4 4
Part No. 2-673-346-01 2-673-327-11 2-673-327-21 2-630-005-31 2-655-582-11
Description PLATE, ORNAMENTAL CABINET (UPPER) (SILVER) CABINET (UPPER) (BLACK) SCREW (M2), NEW TRUSTER, P2 (BLACK) SCREW 0+P2 M2 NEWTRU-STAR (SILVER)
Ref. No. 5 5 6 6 7 * 8
Part No. 2-673-247-01 2-673-247-11 2-673-303-01 2-673-303-11 2-673-345-01
Description LID, DC (SILVER) LID, DC (BLACK) LID, JK (SILVER) LID, JK (BLACK) WINDOW (420), LCD
X-2108-909-1 CABINET (REAR) ASSY (420) (SILVER) X-2109-111-1 CABINET (REAR) ASSY (420D) (BLACK)
2-685-484-01 CUSHION (REAR)
DSC-H5_L2 5-3

5-1-2. LCD SECTION
Cabinet (front) section (See page 5-7)
55 51 56 52
0 -15 SY
52 53 58
Lens section (See page 5-6)
60
Main section (See page 5-5)
54 57
LED9001
59
LCD9001
Ref. No. 51 52 * 53 * 54 55 * 56
Part No. 2-666-551-21 3-078-890-01 2-694-714-01 2-673-339-03 A-1176-922-A
Description SCREW, TAPPING, P2 SCREW, TAPPING TAPE CD RETAINER (420) LABEL, FUSE REPLACEMENT CAUTION SW-471 BOARD, COMPLETE
Ref. No.
Part No.
Description FRAME (420), LCD HOLDER (R), LCD HOLDER (L), LCD SCREW, TAPPING, P2 ACX541AKA-1
* 57 2-673-342-01 * 58 2-673-344-01 * 59 2-673-343-01 60 2-666-551-21 LCD9001 8-753-256-97
2-678-099-01 SHEET, SW MUFFLE
LED9001 1-479-403-11 BLOCK, LIGHT GUIDE PLATE (3.0)
DSC-H5_L2 5-4

5-1-3. MAIN SECTION
ns : not supplied
111
LCD9002
113 112
BT9001
102
MS
-30
114
110
106
BT001 ns
109 115
107 105 108
116
-1 SY
50
102
103
SP9001
101
ns
102
104
: BT001 (Lithium battery) SY-150 board on the mount position. (See page 4-29)
Ref. No. * 101 102 * 103 104 105 106 106 106 106 107 * 108 109 109 Part No. 2-684-446-01 3-080-204-11 2-672-564-01 A-1176-978-A A-1176-915-A A-1176-925-A A-1176-926-A A-1176-927-A A-1176-928-A 1-869-227-11 Description SPACER, SP SCREW, TAPPING, P2 SHEET (JK), RADIATION CK-161 FLEXIBLE BOARD, COMPLETE JK-306 FLEXIBLE BOARD, COMPLETE SY-150 BOARD, COMPLETE (SERVICE) (GP1) SY-150 BOARD, COMPLETE (SERVICE) (GP2) SY-150 BOARD, COMPLETE (SERVICE) (GP3) SY-150 BOARD, COMPLETE (SERVICE) (GP4) SW-478 FLEXIBLE BOARD Ref. No. * 110 * 111 112 113 114 * 115 * 116 0 BT001 * BT9001 * BT9001 Part No. 2-677-004-01 2-673-337-01 X-2108-913-1 A-1176-924-A 1-831-557-11 2-694-712-01 2-694-713-01 1-756-539-21 1-780-338-11 1-780-338-21 Description SHEET (INR), RADIATION RETAINER, MODULE ASSY, VF MS-305 BOARD, COMPLETE FLEXIBLE FLAT CABLE (MS-030) USB PROTECTION SHEET USB GASKET BATTERY, LITHIUM SECONDARY TERMINAL BOARD, BATTERY (SILVER) TERMINAL BOARD, BATTERY (BLACK)
2-673-306-01 PLATE, JK GROUND X-2108-910-1 HOLDER ASSY, BATTERY (SILVER) X-2109-112-1 HOLDER (420D), BATTERY (BLACK)
LCD9002 1-802-033-11 LCD MODULE SP9001 1-826-403-21 LOUDSPEAKER (1.0CM)
CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
DSC-H5_L2 5-5

5-1-4. LENS SECTION
ns : not supplied
161
154
157
158
151 153 155 156

IC002
CD -6 17
152 159 160
ns
ns
Ref. No. 151 * 152 153 * 154 155 156 * 157 Part No. A-1177-128-A 2-672-563-01 2-592-693-01 2-672-565-01 1-788-338-11 Description SERVICE, OPTICS UNIT (B191A) (SERVICE) SHEET (LNS), RADIATION PLATE (T), LIGHT INTERCEPTION SHEET (TB), RADIATION OPTICAL FILTER BLOCK Ref. No. 158 159 160 * 161 IC002 Part No. Description
160
2-592-605-01 RUBBER (TM), SEAL 2-672-562-01 SHEET (CD), RADIATION
1-869-222-11 CD-621 FLEXIBLE BOARD A-1176-923-A CD-617 BOARD, COMPLETE (IC002 is not included in this COMPLETE board.) 2-666-551-21 SCREW, TAPPING, P2 2-689-504-01 SHEET (LNS 2), RADIATION A-1176-035-A CCD BLOCK ASSY (CCD IMAGER) (IC002 is not included in this COMPLETE board of CD-617.)
Be sure to read Precautions upon replacing CCD imager on page 4-3 when changing the CCD imager.
DSC-H5_L2 5-6

5-1-5. CABINET (FRONT) SECTION
ns : not supplied
208
ST section (See page 5-8)
209 212 207 210
211 219 202 213
206 205 214

MIC9001
202 215 216

ns
203
202 218 217 202 202
204
202
201
Ref. No. 201 201 202 203 * 204 205 206 207 207 208 209
Part No. X-2108-907-1 X-2109-110-1 3-080-204-11 2-673-230-01 2-673-328-01 2-673-324-11 2-673-323-11 2-673-325-11 2-673-325-21 X-2108-326-1
Description CABINET (FRONT) ASSY (420) (SILVER) CABINET (FRONT) ASSY (420D) (BLACK) SCREW, TAPPING, P2 SCREW, TRIPOD SHEET METAL (R), STRAP RING, ORNAMENTAL RING, LENS GRIP (SILVER) GRIP (BLACK) RELEASE ASSY (420)
Ref. No. * 210 * 211 212 213 * 214 * 215 * 216 217 * 218 219
Part No. 2-673-305-01 2-673-302-01 1-831-558-11 1-479-699-21 2-673-335-01 2-678-097-01 2-673-334-01 A-1176-913-A 2-689-505-01 2-695-940-01
Description PLATE, GRIP GROUND HOLDER, AF FLEXIBLE FLAT CABLE (ST-003) SWITCH BLOCK, CONTROL CUSHION, MICROPHONE CUSHION (B), MICROPHONE HOLDER, MICROPHONE AF-105 FLEXIBLE BOARD, COMPLETE SHEET (TRIPOD), RADIATION SPACER, RELEASE
2-673-301-11 BUTTON, FB
MIC9001 1-542-618-21 MICROPHONE
DSC-H5_L2 5-7

5-1-6. ST SECTION
ns : not supplied
255 254 256
257 258
264
C105
251
Blue
RY201
Red
263
White
261 260 262
259 253
252
251
PRECAUTION DURING SOLENOID PLUNGER INSTALLATION
7 6
5 4 2 3
1 Close the ST cover. 2 Plunger solenoid
3 Two claws 4 Solenoid retainer
5 PL-045 board 6 Apply the soldering in two points. 7 Tapping screw (M1.7x4)
Ref. No. 251 252 253 254 0 255 256 257 257 258
Part No. 3-080-204-11 A-1176-908-A 2-629-818-01 X-2108-912-1 1-479-553-11 A-1176-914-A 2-673-341-01 2-673-341-11 2-673-326-01
Description SCREW, TAPPING, P2 PL-045 BOARD, COMPLETE RETAINER, SOLENOID BASE ASSY, ST FLASH UNIT ST-144 BOARD, COMPLETE EMBLEM (320), ST (SILVER) EMBLEM (320), ST (BLACK) COVER, ST (SILVER)
Ref. No. 258 259 260 261 * 262 263 * 264 0 C105 RY201
Part No. 2-673-326-11 1-964-411-11 1-964-411-21 1-964-411-31 2-678-098-01 A-1176-909-A 2-678-099-01 1-112-763-11 1-455-038-11
Description COVER, ST (BLACK) HARNESS (HA-004) (Red) HARNESS (HA-004) (White) HARNESS (HA-004) (Blue) SHEET, ST ELECTROSTATIC ST-142 BOARD, COMPLETE SHEET, SW MUFFLE CAP, ELECT 320uF 330V SOLENOID, PLUNGER
DSC-H5_L2 5-8

Checking supplied accessories.
Make sure that the following accessories are supplied with your camcorder.
0 Ni-MH battery charger BC-CS2A/CS2B (1) (US,CND,JE,J model) 1-479-378-11 0 Ni-MH battery charger BC-CS2A/CS2B (1) (AEP,UK,E,AUS,HK model) 1-479-378-21 0 Ni-MH battery charger BC-CS2A/CS2B (1) (KR,CH model) 1-479-378-31
HR6 (size AA) Nickel-Metal Hydride batteries (2) (not supplied)
Adaptor ring (1) 2-629-861-01
Battery case (1) 3-074-757-01
Lens cap (1) X-2055-960-1
0 Power cord (Mains lead) (1) (US,CND model) 1-790-107-51 0 Power cord (Mains lead) (1) (AEP,E model) 1-824-910-31 0 Power cord (Mains lead) (1) (AUS model) 1-827-945-41 0 Power cord (Mains lead) (1) (KR model) 1-823-947-51 0 Power cord (Mains lead) (1) (UK model) 1-827-269-22 0 Power cord (Mains lead) (1) (HK model) 1-783-374-22 0 Power cord (Mains lead) (1) (CH model) 1-782-476-41 0 Power cord (Mains lead) (1) (JE, J model) 1-792-549-31
Lens cap strap (1) 3-979-194-31 USB cable (1) 1-829-868-41 CD-ROM (Cyber-shot application software) (1) (Except BR model) 2-666-673-03
AV cable (1) 1-824-519-11
Shoulder strap (1) 2-629-892-01
2-pin conversion adaptor (1) (JE model) 1-569-007-12
Lens hood (1) 2-629-860-01
2-pin conversion adaptor (1) (E model) 1-569-008-12

2-673-175-31 INSTRUCTION (READ THIS FIRST) (NORWEGIAN/DANISH)(AEP) 2-673-176-01 INSTRUCTION (USERS GUIDE) (JAPANESE)(J) 2-673-176-11 INSTRUCTION (USERS GUIDE) (ENGLISH) (US,CND,AEP,UK,E,AUS,HK,JE) 2-673-176-21 INSTRUCTION (USERS GUIDE) (FRENCH/ITALIAN) (CND,AEP) 2-673-176-31 INSTRUCTION (USERS GUIDE) (SPANISH/PORTUGUESE)(AEP,E,JE) 2-673-176-41 INSTRUCTION (USERS GUIDE) (GERMAN/DUTCH)(AEP) 2-673-176-51 INSTRUCTION (USERS GUIDE) (SIMPLIFIED CHINESE/ TRADITIONAL CHINESE)(E,HK,CH,JE) 2-673-176-61 INSTRUCTION (USERS GUIDE) (RUSSIAN)(AEP) 2-673-176-71 INSTRUCTION (USERS GUIDE) (ARABIC/PERSIAN)(E) 2-673-176-81 INSTRUCTION (USERS GUIDE) (KOREAN)(KR,JE) 2-673-176-91 INSTRUCTION (USERS GUIDE) (POLISH/CZECH)(AEP) 2-673-177-11 INSTRUCTION (USERS GUIDE) (HUNGARIAN/SLOVAK) (AEP) 2-673-177-21 INSTRUCTION (USERS GUIDE) (SWEDISH/FINNISH) (AEP) 2-673-177-31 INSTRUCTION (USERS GUIDE) (NORWEGIAN/DANISH) (AEP)
Other accessories
2-673-174-01 INSTRUCTION (READ THIS FIRST) (JAPANESE)(J) 2-673-174-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (US,CND,AEP,UK,E,AUS,HK,JE) 2-673-174-21 INSTRUCTION (READ THIS FIRST) (FRENCH/ITALIAN) (CND,AEP) 2-673-174-31 INSTRUCTION (READ THIS FIRST) (SPANISH/PORTUGUESE)(AEP,E,JE) 2-673-174-41 INSTRUCTION (READ THIS FIRST) (GERMAN/DUTCH) (AEP) 2-673-174-51 INSTRUCTION (READ THIS FIRST) (SIMPLIFIED CHINESE/TRADITIONAL CHINESE) (E,HK,CH,JE) 2-673-174-61 INSTRUCTION (READ THIS FIRST) (RUSSIAN)(AEP) 2-673-174-71 INSTRUCTION (READ THIS FIRST) (ARABIC/PERSIAN)(E) 2-673-174-81 INSTRUCTION (READ THIS FIRST) (KOREAN)(KR,JE) 2-673-174-91 INSTRUCTION (READ THIS FIRST) (CZECH/POLISH) (AEP) 2-673-175-11 INSTRUCTION (READ THIS FIRST) (HUNGARIAN/SLOVAK)(AEP) 2-673-175-21 INSTRUCTION (READ THIS FIRST) (SWEDISH/FINNISH) (AEP)
DSC-H5_L2 5-9
Ver. 1.1 2006. 06
AF-105
5-2. ELECTRICAL PARTS LIST
Ref. No. Part No. Description
CD-617
CK-161
Ref. No. Part No.
JK-306
Description
MS-305
PL-045
A-1176-913-A AF-105 FLEXIBLE BOARD, COMPLETE ****************************** (D001 (AF LED) is not supplied, but this is included in AF-105 flexible board complete.) < DIODE > D001 Not supplied DIODE DOR5073 (AF LED) (D001 (AF LED) is not supplied, but this is included in AF-105 flexible board complete.) < SWITCH > S001 1-762-805-21 SWITCH, PUSH (1 KEY)(LENS COVER OPEN) ************************************************************ A-1176-923-A CD-617 BOARD, COMPLETE ********************** (IC002 is not included in this COMPLETE board.) < CAPACITOR > C002 C004 C005 C006 C007 C009 1-100-566-91 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 10% 25V 16V 16V 16V 16V 25V * CN301 CN302 CN001
A-1176-915-A JK-306 FLEXIBLE BOARD, COMPLETE ******************** < CONNECTOR > 1-794-962-11 CONNECTOR, SQUARE TYPE (USB 5P) < JACK > J001 1-793-620-41 JACK (A/V OUT) ************************************************************ A-1176-924-A MS-305 BOARD, COMPLETE ********************** < CAPACITOR > C301 C302 1-100-786-91 TANTAL. CHIP 1-125-777-11 CERAMIC CHIP < CONNECTOR > 1-816-644-51 FFC/FPC CONNECTOR (LIF) 12P 1-817-827-11 MEMORY STICK DUO CONNECTOR < FERRITE BEAD > FB301 FB302 FB303 FB304 FB305 FB306 1-469-581-21 1-469-581-21 1-469-581-21 1-469-581-21 1-218-990-81 INDUCTOR, FERRITE BEAD (1005) INDUCTOR, FERRITE BEAD (1005) INDUCTOR, FERRITE BEAD (1005) INDUCTOR, FERRITE BEAD (1005) SHORT CHIP 0 (Note1) 0 (Note1) 22uF 0.1uF 20% 10% 6.3V 10V
1-100-566-91 CERAMIC CHIP < CONNECTOR >
* CN001
1-816-057-51 CONNECTOR, FPC (ZIF) 39P 1-218-990-81 SHORT CHIP < RESISTOR > < IC >
IC001 IC002
8-753-230-85 IC CXA3691EN-T9 A-1176-035-A CCD BLOCK ASSY (CCD IMAGER) (IC002 is not included in this COMPLETE of CD-617 board.) < TRANSISTOR >
R302 1-218-953-11 RES-CHIP 1K 5% 1/16W R303 1-218-940-11 RES-CHIP 82 5% 1/16W R304 1-218-940-11 RES-CHIP 82 5% 1/16W ************************************************************ A-1176-908-A PL-045 BOARD, COMPLETE ********************** (RY201 is not included in this COMPLETE board.) < CAPACITOR >
Q001
6-550-119-01 TRANSISTOR < RESISTOR >
DTC144EMT2L
R001 R002 R003 R004 R007
1-218-990-81 1-218-990-81 1-218-982-11 1-218-989-11 1-218-979-11
SHORT CHIP SHORT CHIP RES-CHIP RES-CHIP RES-CHIP
0 0 270K 1M 150K
C201 5% 5% 5% 1/16W 1/16W 1/16W * CN201
1uF
10%
10V
1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P < DIODE >
R010 1-218-977-11 RES-CHIP 100K 5% 1/16W R011 1-218-990-81 SHORT CHIP 0 ************************************************************ A-1176-978-A CK-161 FLEXIBLE BOARD, COMPLETE ****************************** < CONNECTOR > RY201 * CN001 1-817-391-51 CONNECTOR, FPC (ZIF) 31P ************************************************************ D202 D203
8-719-988-61 DIODE 1SS355TE-17 6-500-776-01 DIODE MAZW068H0LS0 < RELAY > 1-455-038-11 SOLENOID, PLUNGER (RY201 is not included in this COMPLETE of PL-045 board.)
Be sure to read Precautions upon replacing CCD imager on page 4-3 when changing the CCD imager.
Note 1: Resistor is mounted to the location where FB305 and FB306 are printed.
DSC-H5_L2 5-10
PL-045
Ref. No. Part No. Description < SWITCH > S201 1-786-179-31 SWITCH, PUSH (1KEY)(FLASH POP UP) ************************************************************ A-1176-909-A ST-142 BOARD, COMPLETE ********************** (C105 is not included in this COMPLETE board.) < CAPACITOR > C101 C102 C103 0 C105 1-100-611-91 1-100-611-91 1-165-908-11 1-112-763-11 CERAMIC CHIP 22uF 20% 6.3V CERAMIC CHIP 22uF 20% 6.3V CERAMIC CHIP 1uF 10% 10V CAP, ELECT 320uF 330V (C105 is not included in this COMPLETE of ST-142 board.) 22uF 20% 6.3V
ST-142
Ref. No. Part No.
ST-144
Description
SW-471
SY-150
< RESISTOR > R001 1-216-121-11 RES-CHIP 1M 5% 1/10W R002 1-216-097-11 RES-CHIP 100K 5% 1/10W ************************************************************ A-1176-922-A SW-471 BOARD, COMPLETE *********************** < CONNECTOR > * CN401 * CN402 1-815-333-51 CONNECTOR, FPC (ZIF) 33P 1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P < DIODE > D401 D402 D403 8-719-064-07 DIODE SML-310LTT86 (ACCESS) 6-500-776-01 DIODE MAZW068H0LS0 8-719-056-23 DIODE MA2S111-(K8).SO < RESISTOR > R401 R402 R403 R404 R405 1-208-671-11 1-218-970-11 1-218-962-11 1-218-970-11 1-218-962-11 METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 330 27K 5.6K 27K 5.6K 0.5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W
C106
* CN101
1-816-644-51 FFC/FPC CONNECTOR (LIF) 12P < DIODE >
D101 0 D102
8-719-056-54 DIODE MAZS068008SO 6-501-096-01 DIODE CRF02 (TE85R) < IC >
< COMPOSITION CIRCUIT BLOCK > RB401 RB402 1-234-376-11 RES, NETWORK 2.2K (1005X4) 1-234-376-11 RES, NETWORK 2.2K (1005X4) < SWITCH > 4.7uH S401 S402 S403 S404 S405 1-786-157-11 1-786-157-31 1-786-157-11 1-786-157-11 1-786-157-11 SWITCH, TACTILE (RIGHT) TACTILE SWITCH (DUST) SWITCH, TACTILE (DOWN) SWITCH, TACTILE (UP) SWITCH, TACTILE (SET)
IC101
6-707-555-01 IC TPS65552RGTR < COIL >
L101
1-456-995-22 INDUCTOR < TRANSISTOR >
Q101
6-550-891-01 TRANSISTOR < RESISTOR >
GT8G133 (T2LSONY.Q)
R103 R104
1-243-975-11 METAL CHIP 1-218-935-11 RES-CHIP
4.7M 33
5% 5%
1/16W 1/16W
< TRANSFORMER > 0 T101 1-443-850-21 DC-DC CONVERTER TRANSFORMER, ************************************************************ A-1176-914-A ST-144 BOARD, COMPLETE ********************** < CAPACITOR > C002 C003 1-100-758-11 CERAMIC CHIP 1-100-761-21 CERAMIC CHIP < DIODE > D001 6-500-811-01 DIODE RR255L-400TE25 < COIL > L001 1-456-193-11 COIL, TRIGGER 0.047uF 0.01uF 10% 10% 250V 250V
S406 1-786-157-11 SWITCH, TACTILE (LEFT) S407 1-786-525-31 TACTILE SWITCH (ZOOM T) S408 1-786-157-11 SWITCH, TACTILE (DISP) S409 1-786-525-31 TACTILE SWITCH (ZOOM W) S410 1-786-157-11 SWITCH, TACTILE (MENU) ************************************************************ SY-150 BOARD, COMPLETE ********************** ************************************************************
Electrical parts list of the SY-150 board is not shown. Pages from 5-12 to 5-15 are not shown.
DSC-H5_L2 5-11E
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]
Toolbar Printing a text

1. Click the Print button . 2. Specify a printer, print range, number of copies, and other options, and then click [OK].
Reversing the screens displayed once

To reverse the previous screens (operation) one by one, click . the To advance the reversed screens (operation) one by one, click the .
Application of printing:
To set a range to be printed within a page, select the graphic and drag on the page to enclose a range to selection tool be printed, and then click the Print button.
Application to the Service Manual:

This function allows you to go and back between circuit diagram and printed circuit board diagram, and accordingly it will be convenient for the voltage check.
Finding a text
1. Click the Find button . 2. Enter a character string to be found into a text box, and click the [Find]. (Specify the find options as necessary)
Moving with link

1. Select either palm tool , zoom tool , text selection tool

To execute find from current page toward the previous pages, select the check box Find Backward and then click the Find.
, or graphic selection tool . 2. Place the pointer in the position in a text where the link exists (such as a button on cover and the table of contents page, or blue characters on the removal flowchart page or drawing page), and the pointer will change to the forefinger form . 3. Then, click the link. (You will go to the link destination.)
Moving with bookmark:

Click an item (text) on the bookmark pallet, and you can move can display the to the link destination. Also, clicking hidden items. (To go back to original state, click ) 3. Open the find dialog box again, and click the [Find Again] and you can find the matched character strings displayed next. (Character strings entered previously are displayed as they are in the text box.)

The parts on the drawing pages (block diagrams, circuit diagrams, printed circuit boards) and parts list pages in a text can be found using this find function. For example, find a Ref. No. of IC on the block diagram, and click the [Find Again] continuously, so that you can move to the Ref. No. of IC on the circuit diagram or printed circuit board diagram successively. Note: The find function may not be applied to the Service Manual depending on the date of issue.
Zooming or rotating the screen display

Zoom in/out Click the triangle button in the zoom control box to select the display magnification. Or, you may click ing in or out. or for zoom-
Switching a page
To move to the first page, click the To move to the last page, click the To move to the next page, click the . . . . Rotate Click rotate tool , and the page then rotates 90 degrees each.
To move to the previous page, click the

The printed circuit board diagram you see now can be changed to the same direction as the set.
Reverse
985211732.pdf
Revision History
Ver. 1.0 1.1 Date 2006.04 2006.06 History Official Release Correction-1 Contents Correction of service note Correction of block diagrams Correction of schematic diagrams Correction of printed wiring boards Correction of electrical parts list S.M. correction: Page 1-3E, 3-1, 3-2, 3-4E, 4-11, 4-27, 5-10 S.M. Rev. issued Yes
DSC-H5_L2

Service Manual: DSC-H5

Uploaded by

Copyright:

Available Formats

Service Manual: DSC-H5

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: DSC-H5

Uploaded by

Copyright:

Available Formats

DSC-H5

Internal memory ON BOARD

Precaution on Replacing the SY-150 board

DIGITAL STILL CAMERA

Sony EMCS Co.

2006F1600-1 2006.06 Published by Kohda TEC

[Input and Output connectors]

Microphone Speaker Exif Print

USB communication Hi-Speed USB (USB 2.0 compliant)

PRINT Image Matching III Compatible PictBridge Compatible

BC-CS2A/CS2B Ni-MH battery charger

Design and specifications are subject to change without notice.

TABLE OF CONTENTS 1. SERVICE NOTE

2-1. DISASSEMBLY 2-3

PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

REPAIR PARTS LIST

5-1. EXPLODED VIEWS 5-3 5-2. ELECTRICAL PARTS LIST 5-10

1-2. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY

Method for copying the data in internal memory

Method for formatting the internal memory

See the following procedure. Cancels the formatting.

PROCESS AFTER FIXING FLASH ERROR

Method for Initializing the Flash Error Code

1-3. PRECAUTION ON REPLACING THE SY-150 BOARD

Ver. 1.1 2006. 06

1-4. VIDEO OUT DEFAULT DATA CHECK

1-5. INITIAL LANGUAGE DATA CHECK

COMMON NOTE FOR DISASSEMBLY

DISCHARGING OF THE FLASHLIGHT POWER SUPPLY CAPACITOR

Discharging the Capacitor

Short jig (1k/1W)

Preparing the Short Jig

Wrap insulating tape.

1 Three screws (M1.7x4) 2 Three screws (M1.7x4) 3 Cabinet (rear) section

(from the light guide plate (3.0) block)

Note: Be very careful not to

A (See page 2-4)

B (See page 2-4)

1 Turn the flexible board. 2 Tapping screw (M1.7x5) 3 Lens section

1 Two tapping screws (M1.7x4) 2 Control switch block

Harnesses of the loudspeaker

Harnesses of the loudspeaker Loudspeaker (1.0cm)

Bend the harnesses of the loudspeaker at the route of the connector.

Route the harnesses with the ST cover closed.

Harness (HA-004) (Blue) , Harness (HA-004)(White), Harness (HA-004) (Red) ST section

Harness (HA-004) (Blue)

Harness (HA-004) (White) Harness (HA-004) (Red)

Blue Red White

Install the microphone tilted as shown in the figure below.

Microphone holder Microphone cushion (B)

Microphone holder Microphone cushion (B) Microphone Microphone cushion

Microphone Microphone cushion

1 Tapping screw (M1.7x4) 2 Strap sheet metal (R)

Cap lever Lens ring

Notch of the lens ring

Ver. 1.1 2006. 06

SY-150 BOARD (1/2)

CA AD0 - CA AD13 X101

S/H A/D CONV.