Project Report
Project Report
CERTIFICATE
This is to certify that the following students of BE(ECE) 8th semester have completed the work on project entitled LASER COMMUNICATION SYSTEM. 1. VARUN RAJ DHIMAN(UE85104) 2. VIJAY PAL(UE85105) 3. VIVEK NEGI(UE85106)
In partial fulfillment of the degree of BE (Electronics and Communication Engineering) by Panjab University, session 2011-12. This record of work carried under the guidance and supervision of the undersigned.
ACKNOWLEDGEMENT
To bring something into existence is truly the work of ALMIGHTY. We thank GOD ALMIGHTY for making this venture a success.
We express our wholehearted thanks to the Management of the college, Ms. Renu Vig ,Director, Mr. Arvind Rajput ,Co-ordinator ECE for providing us an opportunity to do our studies in this esteemed institution. We are extremely grateful to our project incharge Ms. Preeti Gupta for motivating and mentoring us in our project. She has been the guiding light and source of inspiration throughout the project. Besides
providing us with technical assistance she has also been a moral support and motivating figure during difficult times.
At the outset we wish to place on record our sincere thanks to all the staff members of the department of Electronics and Communication Engineering who guided us throughout the entire course.
Vijaypal(UE85105)
Vivek Negi(UE85106)
ABSTRACT
Laser communications systems are wireless connections through the atmosphere. They work similarly to fiber optic links, except the beam is transmitted through free space. While the transmitter and receiver must require line-of-sight conditions, they have the benefit of eliminating the need for broadcast rights and buried cables. Laser communications systems can be easily deployed since they are inexpensive, small, low power and do not require any radio interference studies. The carrier used for the transmission signal is typically generated by a laser diode. This project implements a Laser Communication System, with a laser light as a carrier signal. The project is divided into transmitting and receiving sections. At the transmitter an audio signal is applied to the condenser microphone. The signal is modulated with a laser as a carrier and transmitted through open space. At the receiver a phototransistor detects the signal and demodulation of the received signal is carried out. The demodulated signal is then fed to a loudspeaker where the input audio signal could be heard. The present project involves the study of wireless, open channel communication system using laser as a carrier for audio signals. Using this circuit we can transmit amplified audio signals wirelessly upto a few 20-50 meters. Instead of RF signals, light from a laser torch is used as the carrier in the circuit. The report discusses the construction and working of the project. The various components used in the project are described in brief. The report further discusses the advantages, limitations and applications of the Laser Communication System modelled in this project and other potential areas where Laser Communication System could be implemented.
TABLE OF CONTENTS
1. Introduction.. 9 2. Block Diagram10 3. Block Diagram Explanation ......11
3.1. 3.2. 3.3. 3.4. 3.5. Condenser Microphone.11 Transmitting Section.11 Laser Torch.12 Receiving Section...12 Loud Speaker .....12
4. Circuit Diagram13
4.1. 4.2. Transmitter..13 Receiver13
5. Component Study.....14
5.1. 5.2. 5.3. 5.4. 5.5. 5.6. Operational Amplifier..15 VR (potentiometer/resistance variac/trimmer)..16 Capacitor.16 Battery (9 VOLT)...17 Laser Torch.18 Microphone.19 Integrated Circuit (IC)....19 Phototransistors...19
9. Components Required.26
9.1. 9.2. Transmitter.26 Receiver..........27
10. Advantages.........28 11. Limitations..29 12. Problems Faced .........30 13. Applications.....31 14. Snapshots of Project32 15. Conclusion........34
References
LIST OF FIGURES
1. 2. 3. 4. 5. 6. 7. 8. Transmitter 13 Receiver....14 Symbol of op-amp....... 15 Potentiometer.. 16 Ceramic Capacitor. 16 9V Battery... 17 Laser Torch.. 18 Phototransistor Symbol.... 19
LIST OF TABLES
1. INTRODUCTION
Laser as a communication medium can provide a good substitute for the present day communication systems as the problem of interference faced in case of electromagnetic waves is not there and high deal of secrecy is available. Laser communications offers a viable alternative to RF communications for inter satellite links and other applications where high-performance links are a necessity. High data rate, small antenna size, narrow beam divergence, and a narrow field of view are characteristics of laser communications that offer a number of potential advantages for system design. The present paper involves the study of wireless, open channel communication system using laser a carrier for voice signals. Using this circuit we can communicate with your own neighbours wirelessly. Instead of RF signals, light from a laser torch is used as the carrier in the circuit. The laser torch can transmit light up to a distance of about 500 meters. The phototransistor of the receiver must be accurately oriented towards the laser beam from the torch. If there is any obstruction in the path of laser beam, no sounds will be heard from the receiver. The most important advantage of laser communication is that it allows very fast communication service between two or more devices than other modes of communications. It can provide speed more than 1GBps. So it is much better then LAN or wireless LAN.
2. BLOCK DIAGRAM
LOUD SPEAKER
RECIEVING SECTION
10
It is also called a capacitor or electrostatic microphone. Condenser means capacitor, which stores energy in the form of an electric field. Condenser microphones require power from a battery or external source. Condenser also tends to be more sensitive and responsive than dynamic, making them well suited to capturing subtle nuances in a sound. The diaphragm vibrates when struck by sound waves, changing the distance between the two plates and therefore changing the capacitance. Specifically when the plates are closer together capacitance increases and a charge current occurs and this current will be used to trigger the transmitting section.
The transmitter section comprises condenser microphone, transistor amplifier BC548 followed by an op-amp stage built around IC1. The gain of the op-amp can be controlled with the help of 1-mega ohm pot meter VR1. The AF output from IC1 is coupled to the base of transistor Bd139, which in turn, modulates the laser beam. The transmitter uses 9V power supply. however, the 3-volt laser torch ( after the removal of its battery) can be directly connected to the circuit--with the body of the torch connected to the emitter of BD139 and the spring-loaded lead protruding from inside the torch to circuit ground.
11
Here we use the light rays coming from laser torch as the medium for transmission. Laser had potential for the transfer of data at extremely high rates, specific advancements were needed in component performance and systems engineering, particularly for space-qualified hardware. Free space laser communications systems are wireless connections through the atmosphere. They work similar to fibre optic cable systems except the beam is transmitted through open space. The laser systems operate in the near infrared region of the spectrum. The laser light across the link is at a wavelength of between 780 - 920 nm. Two parallel beams are used, one for transmission and one for reception.
The receiver circuit uses an NPN phototransistor as the light sensor that is followed by a two stage transistor preamplifier and LM386-based audio power amplifier. The receiver doesn't need any complicated alignment. We kept the phototransistor oriented towards the remote transmitter's laser point and adjust the volume control for a clear sound.
A loudspeaker (or "speaker") is an electro acoustic transducer that converts an electrical signal into sound. The speaker moves in accordance with the variations of an electrical signal and causes sound waves to propagate through a medium such as air or water.
12
4. CIRCUIT DIAGRAM
4.1 TRANSMITTER
13
4.2 RECEIVER
5. COMPONENT STUDY
14
The potentiometer is a resistor of variable resistance. It has three terminals; a fixed resistance is found between two of the terminals and the third terminal slides along the fixed resistor. Often, it is used to control the volume in an audio amplifier.
5.3 CAPACITOR:
The capacitor plays a crucial role in electronics -- it stores electrons for when they're needed most. Capacitors consist of two conducting plates placed near each other. Inside the capacitor, the terminals connect to two metal plates separated by a dielectric. The dielectric can be air, paper, plastic or anything else that does not conduct electricity and keeps the plates from touching each other..
16
They can store electric charge for later discharge. Direct current through a capacitor will charge the capacitor for a short time, and then stop flowing. Alternating current, because of the changing electric fields it generates, can flow across a capacitor.
Inside the battery itself, a chemical reaction produces the electrons. The speed of electron production by this chemical reaction (the battery's internal resistance) controls how many electrons can flow between the terminals. Electrons flow from the battery into a wire, and must travel from the negative to the positive terminal for the chemical reaction to take place. That is why a battery can sit on a shelf for a year and still have 17
plenty of power unless electrons are flowing from the negative to the positive terminal, the chemical reaction does not take place. Once you connect a wire, the reaction starts.
5.5LASER TORCH
For this project we have removed the laser assembly from a small laser pointer. The power supply circuit is the green board attached to the brass laser head. We carry similar laser pointers in our catalog that are easily disassembled for this project. The power supply circuit came conveniently marked with a plus and a minus next to two holes in the board. We solder the black negative lead from the battery clip to the hole marked minus. We solder one of the coil leads to the hole marked plus. We solder the red positive lead of the battery clip to the other lead from the coil.
5.6 MICROPHONE
Sound is an amazing thing. All of the different sounds that we hear are caused by minute pressure differences in the air around us. What's amazing about it is that the air transmits those pressure changes so well, and so accurately, over relatively long distances. It was a metal diaphragm attached to a needle, and this needle scratched a pattern onto a piece of metal foil. The pressure differences in the air that occurred when you spoke toward the diaphragm moved the diaphragm, which moved the needle, which was recorded on the foil. When you later ran the needle back over the foil, the vibrations scratched on the foil would then move the diaphragm and recreate the sound. The fact that this purely mechanical system works shows how much energy the vibrations in the 18
air can have! All modern microphones are trying to accomplish the same thing as the original, but do it electronically rather than mechanically. A microphone wants to take varying pressure waves in the air and convert them into varying electrical signals. There are five different technologies commonly used to accomplish this conversion. We use condenser mic in our project.
5.8 PHOTOTRANSISTORS
The standard symbol of a phototransistor, which can be regarded as a conventional transistor housed in a case that enables its semiconductor junctions to be exposed to external light. The device is normally used with its base open circuit, in either of the configurations shown in fig. 5.10.2, and functions as follows.
Fig. 5.6Phototransistor symbol. .In practice, the collector and emitter current of the transistor are virtually identical and, since the base is open circuit, the device is not subjected to significant negative feedback. Consequently, the alternative fig. 5.10.2(b) circuit, in which R1 is connected to Q1 emitter, gives a virtually identical performance to that of fig. The sensitivity of a 19
phototransistor is typically one hundred times greater than that of a photodiode, but is useful maximum operating frequency (a few hundred kilohertz) is proportionally lower than that of a photodiode by using only its base and collector terminals and ignoring the emitter, as shown in fig. Phototransistors are solid-state light detectors with internal gain that are used to provide analog or digital signals. They detect visible, ultraviolet and near-infrared light from a variety of sources and are more sensitive than photodiodes, semiconductor devices that require a pre-amplifier. Phototransistors feed a photocurrent output into the base of a small signal transistor. For each illumination level, the area of the exposed collectorbase junction and the DC current gain of the transistor define the output.
The base current from the incident photons is amplified by the gain of the transistor, resulting in current gains that range from hundreds to several thousands. Response time is a function of the capacitance of the collector-base junction and the value of the load resistance. Photodarlingtons, a common type of phototransistor, have two stages of gain and can provide net gains greater than 100,000. Because of their ease of use, low cost and compatibility with transistor-transistor logic (TTL), phototransistors are often used in applications where more than several hundred nanowatts (nW) of optical power are available. Selecting phototransistors requires an analysis of performance specifications. Collector current is the total amount of current that flows into the collector terminal. Collector dark current is the amount of collector current for which there is no optical input. Typically, both collector current and collector dark current are measured in milliamps (mA). Peak wavelength, the wavelength at which phototransistors are most responsive, is measured in nanometers (nm). Rise time, the time that elapses when a pulse waveform increases from 10% to 90% of its maximum value, is expressed in nanoseconds (ns). Collector-emitter breakdown voltage is the voltage at which phototransistors conduct a specified (nondestructive) current when biased in the normal direction without optical or electrical inputs to the base. Power dissipation, a measure of total power consumption, is measured in milliwatts (mW).
20
6. CIRCUIT DESCRIPTION
There are two sections: the transmitter board and the receiver board, both powered by a separate 9V battery or a fixed voltage power supply, depending on our needs. The transmitter board has an electret microphone module at one end, and the laser diode at the other end. The electronics modulates the intensity of the laser beam according to the output of the microphone. The laser diode has an inbuilt collimating lens, and is simply a module that connects to the transmitter board. The receiver uses a photodiode as the receiving element, and the onboard amplifier powers a small 4-36 ohm speaker. This board is therefore a high gain amplifier with a basic audio output stage. This design uses a higher power (and visible) laser beam, the range is improved, and alignment is easier and not all that critical, especially over a few 20-50 meters. The quality of sound transmitted by the link is good. Clearly, this project is ideal for setting up a speech channel between two areas, say adjacent houses or offices on opposite sides of the street. For duplex (two way) communication, we'll need two laser 'channels. An important feature of transmission by laser beam is privacy. Because a laser beam is intentionally narrow, it's virtually impossible for someone to tap into the link without us knowing. If someone intercepts the beam, the link is broken, signaling the interception. Fibre-optic cables also have high security, as it's very difficult to splice into the cable without breaking the link. Where the transmission distance is no more than meter of so, a LED (or two for increased power) can be substituted for the laser diode. For instance, where the link is being used for educational purposes, such as demonstrating fibre-optic coupling, or the concept of communication over a light beam. The security of the transmission is much lower as LEDs transmit light in all directions. Now to a describe how it all works. We'll start with the transmitter.
6.1
TRANSMITTER
A laser diode needs a certain value of current, called the threshold current, before it emits laser light. A further increase in this current produces a greater light output. The relationship between output power and current in a laser diode is very linear, once the 21
current is above the threshold, giving a low distortion when the beam is amplitude modulated. For example, the 65Onm 5mW laser diode used in this project has a typical threshold current of 3OmA and produces its full output when the current is raised by approximately 1OmA above the threshold to 4OmA. Further increasing the current will greatly reduce the life of the laser diode, and exceeding the absolute maximum of 8OmA will destroy it instantly. Laser diodes are very fragile and will not survive electrostatic discharges and momentary surges! However, if used within specifications, the typical life of one of these lasers is around 20,000 hours. In the transmitter circuit (Fig.1) the laser diode is supplied via an adjustable constant-current source. Note that the metal housing for the laser diode and the lens also acts as a heat sink. The laser diode should not be powered without the metal housing in place. The increasing the voltage at VR1 reduces the laser current. The setting of VR1 determines the quiescent brightness of the laser beam, and therefore the overall sensitivity of the system. The electric microphone is powered through R1 and is coupled to the non inverting input of 1C1 a via capacitor. This input is held at a fixed DC voltage to give a DC output to bias.
6.2
RECEIVER
The transmitted signal is picked up by the photo detector diode in the receiver (shown in Fig.2). The output voltage of this diode is amplified by the common emitter amplifier around T4. This amplifier has a gain of 20 or so, and connects via VR2 to IC2, an LM386 basic power amplifier IC with a gain internally set to 20.This IC can drive a speaker with a resistance as low as four ohms, and 35OmW when the circuit is powered
from a 9V supply. Increasing the supply voltage will increase the output power marginally. Incidentally, the photodiode used for this project has a special clear package, so it responds to visible light, and not just infrared.
22
6.3 MICROPHONE
Sound is an amazing thing. All of the different sounds that we hear are caused by minute pressure differences in the air around us. What's amazing about it is that the air transmits those pressure changes so well, and so accurately, over relatively long distances. It was a metal diaphragm attached to a needle, and this needle scratched a pattern onto a piece of metal foil. The pressure differences in the air that occurred when we spoke toward the diaphragm moved the diaphragm, which moved the needle, which was recorded on the foil. When we later ran the needle back over the foil, the vibrations scratched on the foil would then move the diaphragm and recreate the sound. The fact that this purely mechanical system works shows how much energy the vibrations in the air can have! All modern microphones are trying to accomplish the same thing as the original, but do it electronically rather than mechanically. A microphone wants to take varying pressure waves in the air and convert them into varying electrical signals. There are five different technologies commonly used to accomplish this conversion: 6.3.1 Condenser microphones - A condenser microphone is essentially a capacitor, with one plate of the capacitor moving in response to sound waves. The movement changes the capacitance of the capacitor, and these changes are amplified to create a measurable signal. Condenser microphones usually need a small battery to provide a voltage across the capacitor.
23
7. WORKING
In all of the laser communicators on this page, the laser light is amplitude modulated. This simply means that the amount of light the laser emits varies over time. To understand what is going on, it helps to consider how a loudspeaker makes sound. A loudspeaker is a paper cone attached to a coil of wire that sits in a magnetic field from a strong permanent magnet. When an electric current flows in the loudspeaker coil, the coil becomes an electromagnet, and it moves toward or away from the permanent magnet. As it moves, the paper cone pushes on the air around it, compressing the air in front of it, and expanding the air behind it. Waves of compressed and expanded air travel to your ear, and cause your eardrum to move in time to the movements of the paper cone. The laser communicator adds two components to the loudspeaker concept. We take the electrical signal that goes to the loudspeaker, and connect it instead to the laser, so the laser gets brighter and dimmer as the electric current varies. The second component is the receiver, which converts the light back into an electric current. This current varies in time with the first current, because the amount of light that it receives is varying in time. This second electric current is used to move the paper cone of a loudspeaker, just as before. However, now the loudspeaker can be quite a distance away from the original electric current, without any wires connecting the two.
24
Following tools and instruments are used for preparing the project
1. Soldering iron 2. Desoldering pump 3. Multimeter 4. Screw driver 5. Two 9V Batteries 6. Flux 7. Soldering Wire 8. Various circuit components
25
9. COMPONENTS REQUIRED
9.1 TRANSMITTER:
NAME OF THE COMPONENT Resistance (8.2 K) Resistance (1.8 M) Resistance (10 K) Resistance (15 K) Resistance (82 ohm) Variable Resistance (1 M) Capacitor (1 mf) Capacitor (0.1 mf) Capacitor (470 mf) Capacitor (1000 mf) Semiconductor T1 BC548 Semiconductor T2 BD139 Condenser MIC IC UA741 GCB Table 1
QUANTITY 2 1 1 2 1 1 1 1 1 1 1 1 1 1 1
26
9.2 RECEIVER:
Sl.No. 1. 2 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19.
NAME OF THE COMPONENT Resistor (6.8 K) Resistor (4.7M) Resistor (470 K) Resistor (2.2 K) Resistor (1 K) Resistor (10 K) Variable resistor (50 K) Capacitor (0.01 mf) Capacitor(47 pf) Capacitor (0.1 mf) Capacitor (1 mf) Capacitor (100 mf) Capacitor(10mf) Capacitor(470 mf) Semiconductor 2N5777 Semiconductor BC549 LM 386 GC.B 8 ohm Speaker Table 2
QUANTITY 1 1 1 2 1 1 1 1 1 2 1 2 1 1 1 2 1 1 1
27
10. ADVANTAGES
1. Less costly 2. Circuit can be easily constructed 3. High data rate 4. No communication licenses required. 5. The laser transmission is very secure because it has a narrow beam. 6. There are no recurring line costs. 7. Compatibility with copper or fiber interfaces and no bridge or router requirements. 8. Lasers can also transmit through glass, however the physical properties of the glass have to be considered. 9. Narrow beam divergence 10. Laser transmitter and receiver units ensure easy ,straightforward systems alignment and long-term stable , service free operation, especially in inaccessible environments, optical wireless systems offer ideal, economical alternative to expensive leased lines for buildings.
28
11. LIMITATIONS
1. To avoid 50Hz hum noise in the speaker, the phototransistor should be kept away from AC light sources such as bulbs. The reflected sunlight, however, does not cause any problem. 2. Laser communication works only if the transmitter and receiver are in the line of sight.
29
30
13. APPLICATIONS
1. Using this circuit we can communicate with our neighbours wirelessly. 2. It can be used in inaccessible areas. 3. In future it can be commissioned in satellites for communication. 4. It can be used in conference halls.
31
Transmitter
32
Receiver
33
15. CONCLUSION
After the successful working of the project, it can be concluded that this project is suitable for easy communication. There can be further up gradations in the project which could lead to a much better system for communication. One of the possible way is as follows:Instead of the short range laser, high range lasers can be used which range a few hundred meters.
34
REFERENCES
1. [Online] // wikipedia. - www.wikipedia.com. 2. [Online] // circuitstoday. - www.circuitstoday.com. 3. [Online] // electronics schematics. - www.electroschematic.com. 4. [Online] // electronics for you. - www.efy.com. 5. Electronics for you magazine .
35