Hydraulic Tubes and Pipes

H
GENERAL
INFORMATION
SAE 6000 PSI
TUBES & PIPES
HYDRAULIC PIPES
10-40 BAR
Product
Page
Introduction
187
AISI 316 L Stainless Steel Tube
188
E 355N Hydraulic Tube (St52.4)
189
E 235N Hydraulic Tube (St37.4)
190
Hydraulic Tubes With Blue Passivation
192
Pipe to ANSI B36.19 1/2 4
194
Pipe to ANSI B36.19 5 24
195
Oil Flow Capacity and Pressure Loss
196
Multicore Tubes:
SAE 50 BAR
SAE 3000 PSI
General Information
198
Installation and Assembly, Order Example
200
Maximum Working Pressure, Materials
201
Metric Size Tubes
202
Imperial Size Tubes, Tools and Accessories
203
SAE 6000 PSI
DIN 350-400 BAR

SCHEDULE SERIE
SAE 3000 PSI
SCHEDULE SERIE
SAE 6000 PSI
SCHEDULE SERIE
DIN 350-400 BAR
TUBES & PIPES
GS-PRODUCTS
Introduction
187
GS-Hydro maintains a large stock of carbon and stainless steel pipes & tubes to be utilised in hydraulic and other piping
systems:
TUBES & PIPES
TUBES & PIPES
Manufacturing Tolerances
Technical Terms of Delivery
Material Specification
DIN 2391-1
EN 10305-4
DIN 2391-2/C
EN 10305-4
Stainless Steel (mm)
Stainless Steel (sch)
ASTM A269/A213 (A.W.)
AST A312
ASTM A269
ASTM A530
tubes due to quality (precision in dimension and shape) and
from the marking GS Piping.
cleanliness reasons (no scale) As a comparison hot rolled
In order to ensure quality and traceability GS-Hydro can
tubes will always have some scale both inside and out due
deliver the pipes and tubes with either EN-10204.3.1.B
to the manufacturing process; by cold forming there will
or EN-10204.3.1.C certificates (in accordance with EU
not be any scale inside the tube after the manufacturing.
standard EN 10204 (DIN 50049)). The required certificate,
All precision steel pipes are supplied with trace numbers.
if any, has to be specified by the purchaser.
Stainless steel pipes & tubes

to ASTM A269 / A213 (A.W.) O.D. x W.T. Grade TP
in AISI316L seamless quality from 6 mm to 80 mm O.D.
316L can be supplied with EN - 10204.3.1.B certificate
(=Outer Diameter). Larger O.D. tubes are supplied upon
upon request. The tubes are supplied at a standard length
special order. Seamless cold drawn stainless steel tube
of 6 m. All tubes are supplied plugged with plastic caps.
Tubes up to an O.D. of 75 mm can be supplied electric
tube according to DIN 2391C(EN 10305-4) O.D. x W.T.
zinc plated + yellow passivated or blue passivated (Cr VI-
DIN 1630ST52.4(E 355 N). High tensile strength tube
free alternative) for additional corrosion protection. As all
means higher permissible working pressures and reduced
original GS-Hydto tubes are marked with trace numbers
wall thickness, leading to reduced overall weight. GS-Hydro
the tubes can be supplied with certificates in accordance to
also stocks DIN 2391C(EN 10305-4) O.D. x W.T. DIN
EN 10204.3.1.B, if requested. Cerfitication according to EN
1630ST37.4(E 235 N).
10204.3.1.C is also available upon request. The tubes are
Tubes are supplied in an annealed condition and are
supplied at a standard length of 6 m up to 97 mm. Larger
suitable for cold bending and flaring. External phosphating
O.D. tubes are supplied in random lengths from 4 to 7 m. All
gives corrosion protection and a good base for a paint finish.
tubes are supplied plugged with plastic caps.
MACHINES
GS-Hydro stocks cold drawn seamless high tensile hydraulic
TECHNICAL
INFORMATION
Carbon steel pipes & tubes
OTHER
COMPONENTS
ADAPTORS
GS-Hydro maintains a large stock of stainless steel tubes
SAE J514 JIC

FLARE FITTINGS
Original GS-Hydro high pressure piping can be recognised
HOSES &
HOSE COUPLINGS
GS-Hydro recommends the use of cold drawn pipes &
BITE TYPE
FITTINGS
VALVES
Manufacturing Tolerances
DIN 1630
CLAMPS
Carbon Steel
Material Specification
GS-PRODUCTS
TUBES & PIPES

Seamless Colddrawn Stainless Steel Tube - AISI 316 L
TUBES & PIPES
188
All working pressures are based on Det Norske Veritas Rules for Classification of Ships Newbuilding Part 4, Chapter 1,
Section 6 and Mobile Offshore Units Drilling Plant (Drill) Part 6, Chapter 5, Section 6.
Allowable stress is based on the lowest of the following criteria:
Yield
Delta t =
1,6

CLAMPS
O.D x W.T
ID Code
W. P. bar
*1
B.P. bar
*2
kg/m
Delta t =

NOK/m
6 x 1.0
33010610
525
2120
0.07
123,-
8 x 1.0
33010810
379
1514
0.17
171,-
VALVES
8 x 1.5
33010815
602
2446
0.24
198,-
10 x 1.0
33011010
297
1178
0.22
174,-
10 x 1.5
33011015
465
1871
0.31
244,-
10 x 2.0
33011020
650
2650
0.40
340,-
12 x 1.0
33011210
244
964
0.27
207,-
12 x 1.5
33011215
379
1514
0.39
251,-
12 x 2.0
33011220
525
2120
0.49
340,-
BITE TYPE
FITTINGS
12 x 2.5
33011225
682
2789
0.59
15 x 1.5
33011515
297
1178
0.50
333,-
16 x 1.5
33011615
277
1097
0.54
318,-
16 x 2.0
33011620
379
1514
0.69
393,-
16 x 2.5
33011625
487
1963
0.83
457,-
18 x 1.5
33011815
244
964
0.61
381,-
SAE J514 JIC

FLARE FITTINGS
18 x 2.0
33011820
333
1325
0.79
416,-
20 x 2.0
33012020
297
1178
0.89
425,-
20 x 2.5
33012025
379
1514
1.08
510,-
20 x 3.0
33012030
465
1871
1.26
558,-
22 x 1.5
33012215
197
776
0.76
398,476,-
HOSES &
HOSE COUPLINGS
22 x 2.0
33012220
268
1060
0.99
25 x 1.5
33012515
172
677
0.87
25 x 2.0
33012520
233
922
1.13
498,-
25 x 2.5
33012525
297
1178
1.39
568,-
25 x 3.0
33012530
362
1445
1.63
679,-
25 x 4.0
33012540
501
2019
2.07
728,-
28 x 2.0
33012820
207
815
1.28
595,-
28 x 2.5
33012825
263
1039
1.57
28 x 3.0
33012830
320
1272
1.85
ADAPTORS
30 x 2.0
33013020
192
757
1.38
790,-
30 x 2.5
33013025
244
964
1.70
713,-
30 x 3.0
33013030
297
1178
2.00
783,-
30 x 4.0
33013040
408
1631
2.56
1170,-
35 x 2.0
33013520
164
642
1.63
764,-
35 x 2.5
33013525
207
815
2.00
848,-
OTHER
COMPONENTS
35 x 3.0
33013530
251
994
2.37
975,-
38 x 2.5
33013825
190
746
2.19
1016,-
38 x 3.0
33013830
230
909
2.59
1037,-
38 x 4.0
33013840
314
1247
3.35
1272,1967,-
38 x 5.0
33013850
402
1606
4.07
42 x 2.0
33014220
135
530
1.97
42 x 2.5
33014225
171
671
2.43
1061,-
42 x 3.0
33014230
207
815
2.89
1229,-
42 x 4.0
33014240
282
1116
3.75
1695,-
MACHINES
50 x 3.0
33015030
172
677
3.48
1391,-
50 x 5.0
33015050
297
1178
5.55
1993,-
50 x 6.0
33015060
362
1445
6.50
2131,-
60 x 3.0
33016030
142
588
4.22
1713,-
TECHNICAL
INFORMATION
60 x 5.0
33016050
244
964
6.78
2460,-
66 x 8.5
33016685
392
1567
12.05
3975,-
80 x 10.0
33018010
379
1514
17.21
5473,-
x = Price on request
Tensile

2,7
Aisi 316 Tube: Yield = 276 MPa, Tensile = 530

MPa, Allowable stress 172 MPa. Yield and
tensile based on material certificate from GSHydro.
T = t0 + b + tolerances
b = 0.1333t0
_ 10% of wall thickness
Tolerances are +
t0 =
P x D
2 x Delta t + P
P= Pressure Mpa
D= Diameter mm (outer dia.)
*1: Bending and production tolerances included.
*2: Burst pressure based on Tensile value.
Not included tolerance of wall thickness.
Seamless Cold drawn Stainless Steel

Tube To ASTM 269 TP 316L / DIN 2391 - C
(EN 10305-4) supplied with EN - 10204.3.1.B
Certificate.
Standard lengths 6m.
All tubes are plugged with plastic caps.
GS-PRODUCTS
Hydraulic Tube E 355N (St. 52.4) NBK To DIN 2391C / 2445 (EN 10305-4)
All working pressures are based on Det Norske Veritas Rules for Classification of Ships Newbuilding Part 4,
Chapter 1, Section 6, and Mobile Offshore Units Drilling Plant (Drill) Part 6, Chapter 5, Section 6.
Allowable stress, Delta t, is based on the lowest of the following criteria:
Tensile

2,7
kg/m
NOK/m
14 x 2.0
31011420
411
473
1777
0.59
81,-
15 x 1.5
31011515
259
297
1184
0.50
74,-
15 x 2.0
31011520
381
438
1640
0.61
90,-
16 x 1.5
31011615
242
277
1103
0.54
75,-
16 x 2.0
31011620
355
408
1522
0.69
93,-
16 x 2.5
31011625
475
547
1974
0.83
110,-
18 x 1.5
31011815
214
244
969
0.61
80,-
18 x 2.0
31011820
313
358
1333
0.79
100,-
20 x 2.0
31012020
279
319
1184
0.89
104,-
20 x 2.5
31012025
371
426
1523
1.08
125,146,-
20 x 3.0
31012030
467
537
1881
1.25
22 x 1.5
31012215
173
197
780
0.76
86,-
22 x 2.0
31012220
252
288
1066
0.99
111,-
25 x 2.0
31012520
220
251
927
1.13
129,-
25 x 2.5
31012525
291
333
1184
1.39
155,-
25 x 3.0
31012530
365
418
1454
1.63
200,-
28 x 2.0
31012820
195
223
820
1.28
140,-
28 x 3.0
31012830
322
369
1279
1.85
197,-
30 x 2.0
31013020
182
207
761
1.38
149,-
30 x 3.0
31013030
299
343
1184
2.00
211,-
30 x 4.0
31013040
424
487
1640
2.56
268,-
35 x 2.0
31013520
155
176
646
1.63
172,-
35 x 3.0
31013530
254
290
999
2.37
246,-
38 x 3.0
31013830
233
266
914
2.59
269,-
38 x 4.0
31013840
327
375
1254
3.35
344,-
42 x 2.0
31014220
128
146
533
1.97
42 x 3.0
31014230
209
239
820
2.89
297,382,-
42 x 4.0
31014240
293
336
1122
3.75
46 x 8.5
31014685
601
695
2244
7.84
50 x 5.0
31015050
315
361
1184
5.55
516,-
56 x 8.5
31015685
516
595
1908
9.96
1033,-
60 x 5.0
31016050
259
297
969
6.78
638,-
65 x 8.0
31016580
407
468
1496
11.25
66 x 8.5
31016685
429
494
1576
12.05
1228,1175,-
72 x 7.0
31017270
313
358
1148
11.22
75 x 5.0
31017550
205
234
761
8.63
811,-
80 x 10.0
31018010
418
481
1523
17.21
1798,-
90 x 5.0
31019050
169
193
627
10.48
1003,-
97 x 12.0
31019712
416
478
1505
25.15
2738,-
115 x 15.0
310111515
444
511
1599
36.95
3894,-
130 x 15.0
310113015
388
445
1390
42.54
4630,-
150 x 15.0
310115015
332
380
1184
49.94
190 x 20.0
310119020
353
405
1254
83.84
250 x 25.0
310125025
335
384
1184
138.71
VALVES
*3
BITE TYPE
FITTINGS
B.P. bar
*2
SAE J514 JIC

FLARE FITTINGS
W.P. bar
*1
HOSES &
HOSE COUPLINGS
ID Code
ADAPTORS
The Tubes are phosphated and oiled

inside and outside, and supplied with
EN - 10204.3.1.B Certificate.
Standard lengths 6m up to 97 x 12mm.
From 115 x 15mm to 250 x 25mm the
tubes are supplied in random lengths
from 4 to 7m.
All tubes are plugged with plastic
caps.
O.D x W.T
P= Pressure Mpa
OTHER
COMPONENTS
* 1: Bending, corrosion and production tolerances included.

* 2: Corrosion and production tolerances included.
* 3: Burst pressure based on Tensile value.
CLAMPS
E 355N: Yield = 355 MPa, Tensile = 533 MPa, Allowable stress 197 MPa. Yield and tensile based on
material certificate from GS-Hydro.
T = t0 + b + c + tolerances, b = 0,1333t0, c = 0,3 mm for hydraulic
Tolerances are +
P x D
t0 =
2 x Delta t + P
MACHINES
Delta t =

TECHNICAL
INFORMATION
Yield
Delta t =
1,8

189
TUBES & PIPES
TUBES & PIPES
GS-PRODUCTS
TUBES & PIPES

Hydraulic Tube E 235N (St. 37.4) NBK to DIN 2391C / 2445 (EN 10305-4)
TUBES & PIPES
190
All working pressures are based on Det Norske Veritas Rules for Classification of Ships Newbuilding Part 4,
Chapter 1, Section 6, and Mobile Offshore Units Drilling Plant (Drill) Part 6, Chapter 5, Section 6.
Yield
Delta t =
1,8

Delta t =

Tensile

2,7
CLAMPS
E 235N: Yield = 235 MPa, Tensile = 390 MPa, Allowable stress 130 MPa. Yield and tensile based on
material certificate from GS-Hydro.
_ 10% of wallthickness
Tolerances are +
t0 =
P x D
2 x Delta t + P
VALVES
*1: Bending, corrosion and production tolerances included.

*2: Corrosion and production tolerances included.
*3: Burst pressure based on Tensile value.
O.D x W.T
ID Code
W.P. bar
BITE TYPE
FITTINGS
*1
B.P. bar
*2
*3
P= Pressure Mpa
kg/m
NOK/m
4 x 1.0
32010410
397
459
2600
0.05
59,-
6 x 1.0
32010610
252
289
1560
0.07
40,42,-
6 x 1.5
32010615
475
552
2600
0.17
6 x 2.0
32010620
736
867
3900
0.19
8 x 1.0
32010810
184
211
1114
0.17
45,-
SAE J514 JIC

FLARE FITTINGS
8 x 1.5
32010815
341
393
1800
0.24
47,-
8 x 2.0
32010820
515
600
2600
0.30
62,-
8 x 2.5
32010825
712
838
3545
0.34
50,-
10 x 1.0
32011010
145
166
867
0.22
47,-
10 x 1.5
32011015
265
305
1376
0.31
47,-
10 x 2.0
32011020
397
459
1950
0.40
62,-
HOSES &
HOSE COUPLINGS
10 x 2.5
32011025
540
630
2600
0.46
12 x 1.5
32011215
218
249
1114
0.39
50,-
12 x 2.0
32011220
322
371
1560
0.49
12 x 2.5
32011225
435
504
2053
0.59
65,-
14 x 1.5
32011415
184
211
936
0.46
14 x 2.0
32011420
271
312
1300
0.59
15 x 1.5
32011515
171
196
867
0.50
65,-
15 x 2.0
32011520
252
289
1200
0.64
80,-
ADAPTORS
16 x 1.5
32011615
160
183
807
0.54
16 x 2.0
32011620
234
269
1114
0.69
16 x 2.5
32011625
313
361
1444
0.83
16 x 3.0
32011630
397
459
1800
0.96
18 x 1.5
32011815
141
161
709
0.61
18 x 2.0
32011820
206
236
975
0.79
OTHER
COMPONENTS
20 x 2.0
32012020
184
211
867
0.89
20 x 2.5
32012025
245
281
1114
1.08
20 x 3.0
32012030
308
355
1376
1.26
20 x 4.0
32012040
443
514
1950
1.58
22 x 1.5
32012215
114
130
571
0.76
22 x 2.0
32012220
166
190
780
0.99
22 x 2.5
32012225
221
253
1000
1.09
25 x 2.0
32012520
145
166
678
1.13
MACHINES
25 x 2.5
32012525
192
220
867
1.39
25 x 3.0
32012530
241
276
1064
1.63
25 x 4.0
32012540
343
395
1486
2.07
TECHNICAL
INFORMATION
Definitions of tube/pipe:

All tubes are specified with outside dia. in millimeters or inches.

All pipes are specified with normal dia.
For example a 2 N.D. pipe will measure 60.3 mm O.D. on pipe,
and the wall thickness has to be specified.
The Tubes are phosphated and oiled

inside and outside, and supplied with
EN - 10204.3.1.B Certificate. Standard
lengths 6m. All tubes are plugged with
plastic caps.
All working pressures are based on Det Norske Veritas Rules for Classification of Ships Newbuilding Part 4, Chapter 1,
Section 6, and Mobile Offshore Units Drilling Plant (Drill) Part 6, Chapter 5, Section 6.
Yield
Tensile
Delta t =
Delta t =

1,8
2,7

E 235N: Yield = 235 MPa, Tensile = 390 MPa, Allowable stress 130 MPa. Yield and tensile based on material certificate
from GS-Hydro.
Tolerances are +
P x D
2 x Delta t + P
* 1: Bending, corrosion and production tolerances included.

* 2: Corrosion and production tolerances included.
* 3: Burst pressure based on Tensile value.
W.P. bar
*1
B.P. bar
*2
kg/m
*3
NOK/m
28 x 2.0
32012820
129
147
600
1.28
28 x 2.5
32012825
170
195
765
1.57
28 x 3.0
32012830
213
244
936
1.85
30 x 2.0
32013020
120
137
557
1.38
30 x 3.0
32013030
197
226
867
2.00
30 x 4.0
32013040
279
321
1200
2.56
35 x 2.0
32013520
102
116
473
1.63
35 x 3.0
32013530
167
191
731
2.37
38 x 2.5
32013825
123
141
549
2.19
38 x 3.0
32013830
153
175
669
2.59
38 x 4.0
32013840
216
247
918
3.35
38 x 5.0
32013850
281
323
1182
4.07
38 x 6.0
32013860
349
403
1463
4.74
42 x 2.0
32014220
85
96
390
1.97
42 x 3.0
32014230
138
158
600
2.89
42 x 4.0
32014240
194
222
821
3.75
50 x 3.0
32015030
115
131
498
3.48
336,-
60 x 3.0
32016030
95
108
411
4.22
403,-
75 x 3.0
32017530
76
86
325
5.32
511,-
90 x 3.5
32019035
75
85
316
7.47
757,-
115 x 4.0
320111540
68+
77
281
10.98
1186,-
140 x 4.5
320114045
63
72
260
15.04
1787,-
165 x 5.0
320116550
60
68
244
19.73
2389,-
220 x 6.0
320122060
54
62
219
31.66
4435,-
273 x 6.0
320127360
44
49
175
39.41
Design working pressure in psi x 1000
6.4.4. Det Norske Veritas requirement

for maximum woeking pressure
GS-PRODUCTS
MACHINES
Required burst pressure of 4 times maximum allowable working pressure may be

reduced according to the curve in Fig. 6.1,
when the working pressures are above 207
bars ( 3000 psi )
SAE J514 JIC

FLARE FITTINGS
ID Code
HOSES &
HOSE COUPLINGS
O.D x W.T
ADAPTORS
NOTE: When cold bending a pipe or

tube, the yield and tensility increases
and the elongation decreases. Therefore a cold bent pipe can take more
pressure than a straight pipe.
Unfortunately the calculation code
does not take this into consideration,
it bases this on the reduction in wallthickness due to cold bending.
OTHER
COMPONENTS
The Tubes are phosphated and oiled inside and outside, and supplied with EN - 10204.3.1.B Certificate.
Standard lengths 6m. All tubes are plugged with plastic caps.
BITE TYPE
FITTINGS
VALVES
P= Pressure Mpa
Fig. 6.1
Design working pressure in bar
TECHNICAL
INFORMATION
t0 =
191
TUBES & PIPES
CLAMPS
TUBES & PIPES
GS-PRODUCTS
TUBES & PIPES

Hydraulic Tubes with Blue Passivation Surface
TUBES & PIPES
192
The Tubes are supplied with EN-10204.3.1.B Material Certificate.

Standard lengths 6m.
All tubes are plugged with plastic caps.
For protection against corrosion the tubes are covered inside and outside with
Wendolit K 728 accordint to DIN 50017.
CLAMPS
El.Zinc plated w/blue passivation surface (CR-VI-Free)
O.D x W.T
ID Code
6 x 1.0
6 x 1.5
W.P. bar
B.P. bar
VALVES
BITE TYPE
FITTINGS
kg/m
NOK/m
1300
0.07
61,-
1950
0.17
62,-
330
975
0.17
65,-
342
528
1463
0.24
65,-
32021010
146
257
780
0.22
67,-
10 x 1.5
32021015
267
406
1170
0.31
68,-
12 x 1.5
32021215
218
330
975
0.39
71,-
12 x 2.0
32021220
321
459
1300
0.49
87,-
50 x 3.0
32025030
115
148
418
3.48
415,-
60 x 3.0
32026030
95
123
340
4.22
530,-
75 x 3.0
32027530
76
97
312
5.32
580,-
*1
*2
*3
32020610
252
458
32020615
477
755
8 x 1.0
32020810
184
8 x 1.5
32020815
10 x 1.0
SAE J514 JIC

FLARE FITTINGS
El.Zinc plated w/blue passivation surface (CR-VI-Free)
O.D x W.T
ID Code
15 x 1.5
15 x 2.0
W.P. bar
B.P. bar
kg/m
NOK/m
HOSES &
HOSE COUPLINGS
ADAPTORS
OTHER
COMPONENTS
MACHINES
TECHNICAL
INFORMATION
*1
*2
*3
31021515
260
297
1184
0.50
90,-
31021520
380
438
1640
0.64
108,-
16 x 1.5
31021615
243
277
1103
0.54
93,-
16 x 2.0
31021620
354
408
1522
0.69
111,-
16 x 2.5
31021625
475
547
1974
0.83
135,-
18 x 1.5
31021815
214
244
969
0.61
99,-
18 x 2.0
31021820
312
358
1333
0.79
122,-
20 x 2.0
31022020
278
319
1184
0.89
125,-
20 x 2.5
31022025
371
425
1523
1.08
149,-
20 x 3.0
31022030
467
538
1881
1.26
171,-
22 x 1.5
31022215
173
198
780
0.76
113,-
22 x 2.0
31022220
251
288
1061
0.99
135,-
25 x 2.0
31022520
220
251
927
1.13
158,-
25 x 2.5
31022525
291
333
1184
1.39
185,-
25 x 3.0
31022530
365
418
1454
1.63
210,-
28 x 2.0
31022820
195
223
820
1.28
172,-
28 x 3.0
31022830
323
370
1279
1.85
233,-
30 x 2.0
31023020
181
207
761
1.38
199,-
30 x 3.0
31023030
299
343
1184
2.00
269,-
30 x 4.0
31023040
423
487
1640
2.56
313,-
35 x 2.0
31023520
154
176
646
1.63
243,-
35 x 3.0
31023530
254
290
999
2.37
271,-
38 x 3.0
31023830
232
266
914
2.59
339,-
38 x 4.0
31023840
327
375
1254
3.35
439,-
42 x 3.0
31024230
209
239
820
2.89
377,-
42 x 4.0
31024240
293
336
1122
3.75
500,-
50 x 5.0
31025050
316
361
1184
5.55
703,-
50 x 6.0
31025060
390
448
1454
6.50
810,-
60 x 5.0
31026050
260
297
969
6.18
870,-
60 x 6.0
31026060
319
366
1077
7.97
870,-
75 x 5.0
31027550
205
234
761
8.63
922,-
Hydraulic tube DIN 2391 C/DIN 2445 (EN 10305-4) St. 37.4.
The tubes are phosphated and annealed
Note: Permissable stress E 235N 157 MPa
O.D x W.T
Static
Dynamic
kg/m
4 x 1.0
707
555
0.05
6 x 1.0
471
394
0.07
6 x 1.5
707
555
0.17
6 x 2.0
942
697
0.19
8 x 1.0
353
305
0.17
8 x 1.5
530
436
0.24
8 x 2.0
707
692
0.30
8 x 2.5
883
663
0.34
10 x 1.0
283
249
0.22
10 x 1.5
424
359
0.31
10 x 2.0
565
419
0.40
10 x 2.5
707
555
0.48
12 x 1.5
353
305
0.39
12 x 2.0
471
394
0.49
12 x 2.5
589
477
0.59
14 x 1.5
303
266
0.48
14 x 2.0
404
344
0.59
15 x 1.5
283
249
0.50
O.D x W.T
Static
Dynamic
kg/m
500
404
0.39
Maximum working pressure for E 355N and E 235N

tube according to:
- static
DIN 2413/I straight tube only
- dynamic DIN 2431/III straight tube only
GS-PRODUCTS
193
VALVES
Note: Corrosion allowance not included.

Wall thickness tolerance 10% included.
Bending allowance not included.
Hydraulic tube DIN 2391 C/DIN 2445 ST. 52.4
The tubes are phosphated and annealed.
Note: Permissable stress St. 52.4. = 222 MPa
12 x 2.0
666
522
0.49
16 x 2.0
353
305
0.69
14 x 2.0
571
456
0.59
16 x 2.5
442
372
0.83
15 x 1.5
400
330
0.50
16 x 3.0
530
436
0.96
15 x 2.0
533
429
0.64
18 x 1.5
236
211
0.61
16 x 1.5
375
311
0.64
18 x 2.0
314
272
0.79
16 x 2.0
500
404
0.69
20 x 2.0
283
249
0.89
16 x 2.5
624
493
0.83
20 x 2.5
353
305
1.08
18 x 1.5
333
279
0.61
20 x 3.0
424
359
1.26
18 x 2.0
444
364
0.79
20 x 4.0
565
461
1.58
20 x 2.0
400
330
0.89
22 x 1.5
193
175
0.76
20 x 2.5
500
404
1.08
22 x 2.0
257
228
0.99
20 x 3.0
599
476
1.26
272
231
0.76
22 x 2.5
321
280
1.09
22 x 1.5
24 x 2.0
223
196
1.13
22 x 2.0
363
303
0.99
25 x 2.5
283
249
1.39
25 x 2.0
320
269
1.13
25 x 3.0
339
294
1.63
25 x 2.5
400
330
1.39
25 x 4.0
452
380
2.07
25 x 3.0
480
390
1.63
28 x 2.0
202
182
1.28
28 x 2.0
285
242
1.28
28 x 2.5
252
225
1.57
28 x 3.0
428
352
1.85
28 x 3.0
303
266
1.85
30 x 2.0
266
226
1.38
30 x 2.0
188
171
1.38
30 x 3.0
400
330
2.00
30 x 3.0
283
249
2.00
30 x 4.0
533
429
2.56
30 x 4.0
377
324
2.56
35 x 2.0
228
196
1.38
35 x 2.0
161
148
1.38
35 x 3.0
343
286
2.37
35 x 3.0
242
216
2.37
38 x 3.0
315
265
2.59
38 x 2.5
189
169
2.19
38 x 4.0
421
346
3.35
38 x 3.0
223
200
2.59
42 x 2.0
190
164
1.97
38 x 4.0
297
261
3.35
42 x 3.0
285
242
2.89
38 x 5.0
372
320
4.07
42 x 4.0
381
316
3.75
38 x 6.0
446
376
4.74
50 x 5.0
400
330
5.55
42 x 2.0
135
124
1.97
56 x 8.5
607
481
9.96
42 x 3.0
202
182
2.89
60 x 5.0
333
279
6.78
42 x 4.0
269
228
3.75
65 x 8.0
498
399
11.25
50 x 3.0
170
155
3.48
66 x 8.5
515
415
12.05
60 x 3.0
141
130
4.22
75 x 5.0
266
226
8.63
75 x 3.0
113
105
5.32
80 x 10.0
500
404
17.21
90 x 3.5
110
102
7.47
90 x 5.0
222
190
10.48
115 x 4.0
98
92
10.98
97 x 12.0
494
401
25.15
140 x 4.5
91
85
15.04
115 x 15.0
521
420
36.95
165 x 5.0
85
80
19.73
130 x 15.0
461
376
42.54
220 x 6.0
77
72
31.66
150 x 15.0
400
330
49.94
NOTE: All tubes are supplied with material certificate to EN - 10204.3.1.B
SAE J514 JIC

FLARE FITTINGS
0.64
HOSES &
HOSE COUPLINGS
0.64
235
ADAPTORS
324
266
OTHER
COMPONENTS
377
16 x 1.5
MACHINES
15 x 2.0
12 x 1.5
BITE TYPE
FITTINGS
Working Pressure bar
TECHNICAL
INFORMATION
Working Pressure bar
TUBES & PIPES
Working pressure to DIN 2413 Parts 1 and 3. Only for straight tube and landbased
CLAMPS
TUBES & PIPES
GS-PRODUCTS
TUBES & PIPES

Pipe to ANSI B36.19 ASTM - A - 312 - TP - 316 L
TUBES & PIPES
All working pressures are based on ANSI B31.3 304.1/3B. Allowable stress is based on the lowest of the following criteria:
194
Delta t =

Yield 2
3
Delta t =

Tensile

3
ASTM A 312 TP 316 Pipe: Yield = 234 MPa, Tensile = 515 MPa, Allowable stress Delta t 156 MPa. Yield and tensile
based on material certificate from GS-Hydro.
_ 12,5% of wall thickness
b = 0.1333t0
Tolerances are +
CLAMPS
t0 =
P x D
2 x Delta t
W.P. bar
P= Pressure Mpa
B.P. bar
VALVES
Nom. pipe size

NPS x SCH Size
O.D x W.T
ID Code
*1
*2
*3
1/2 SCH 10
21.34 x 2.11
33012134211
238
270
1/2 SCH 40
21.34 x 2.77
33012134277
313
1/2 SCH 80
21.34 x 3.73
33012134373
1/2 SCH 160
21.34 x 4.78
1/2 SCH xxs
BITE TYPE
FITTINGS
SAE J514 JIC
FLARE FITTINGS
HOSES &
HOSE COUPLINGS
ADAPTORS
OTHER
COMPONENTS
kg/m
NOK/m
1018
1.02
354
1337
1.29
421
477
1800
1.65
33012134478
540
611
2307
1.98
21.34 x 7.47
33012134747
843
956
3605
2.55
3/4 SCH 10
26.67 x 2.11
33012667211
191
216
815
1.30
3/4 SCH 40
26.67 x 2.81
33012667281
254
288
1085
1.71
3/4 SCH 80
26.67 x 3.91
33012667391
353
400
1510
2.33
3/4 SCH 160
26.67 x 5.56
33012667556
502
569
2147
2.94
3/4 SCH xxs
26.67 x 7.82
33012667277
706
800
3020
3.64
1 SCH 10
33.40 x 2.77
33013340277
200
226
854
2.13
1 SCH 40
33.40 x 3.38
33013340338
244
276
1042
2.54
1 SCH 80
33.40 x 4.55
33013340455
328
372
1403
3.29
1 SCH 160
33.40 x 6.35
33013340635
458
519
1958
4.30
1 SCH xxs
33.40 x 9.09
33013340909
656
743
2803
5.45
1 1/4 SCH 10
42.16 x 2.77
33014216277
158
179
677
2.73
1 1/4 SCH 40
42.16 x 3.56
33014216356
203
231
870
3.44
1 1/4 SCH 80
42.16 x 4.85
33014216485
277
314
1185
4.53
1 1/4 SCH 160
42.16 x 6.35
33014216635
363
411
1551
5.69
1 1/4 SCH xxs
42.16 x 9.70
33014216970
554
628
2370
7.76
1 1/2 SCH 10
48.26 x 2.77
33014826277
138
157
591
3.16
1 1/2 SCH 40
48.26 x 3.68
33014826368
184
208
785
4.11
1 1/2 SCH 80
48.26 x 5.08
33014826508
254
287
1084
5.49
1 1/2 SCH 160
48.26 x 7.14
33014826714
356
404
1524
7.35
1 1/2 SCH xxs
48.26 x 10.16
330148261016
507
575
2168
9.55
2 SCH 10
60.30 x 2.77
33016030277
111
125
473
3.99
2 SCH 40
60.30 x 3.91
33016030391
156
177
668
5.52
2 SCH 80
60.30 x 5.54
33016030554
221
251
946
7.60
2 SCH 160
60.30 x 8.74
33016030874
349
396
1493
11.28
2 SCH xxs
60.30 x 11.07
330160301107
442
501
1891
13.44
2 1/2 SCH 5
73.00 x 2.11
33017303211
70
79
298
3.76
2 1/2 SCH 10
73.00 x 3.05
33017303305
101
114
430
5.37
2 1/2 SCH 40
73.00 x5.16
33017303516
170
193
728
8.80
2 1/2 SCH 80
73.00 x7.01
33017303701
231
262
989
11.64
2 1/2 SCH 160
73.00 x 9.53
33017303953
314
356
1345
15.15
2 1/2 SCH xxs
73.00 x 14.02
330173031402
463
524
1978
20.50
3 SCH 5
88.90 x 2.11
33018890211
57
65
244
4.59
3 SCH 10
88.90 x 3.05
33018890305
83
94
353
6.45
3 SCH 40
88.90 x 5.49
33018890549
149
169
636
11.46
MACHINES
3 SCH 80
88.90 x 7.67
33018890767
208
236
889
15.51
3 SCH 160
88.90 x 11.13
330188901113
302
342
1290
21.67
3 SCH xxs
88.90 x 15.24
330188901524
413
468
1766
27.68
4 SCH 5
114.30 x 2.11
330111430211
44
50
190
5.93
4 SCH 10
114.30 x 3.05
330111430305
64
73
275
8.50
4 SCH 40
114.30 x 6.07
330111430607
128
145
547
16.32
TECHNICAL
INFORMATION
4 SCH 80
114.30 x 8.56
330111430856
180
204
771
22.67
4 SCH 160
114.30 x 13.49
3301114301349
284
322
1216
34.05
4 SCH xxs
114.30 x 17.12
3301114301712
361
409
1543
41.03
*1: Bending and production

tolerances included.
Bending factor b is taken
from DNV rules.
*2: Production tolerances
included
*3: Burst pressure based
on Tensile value.
Not included tolerance of
wall thickness.
GS-PRODUCTS
Pipe to ANSI B36.19 ASTM - A - 312 - TP - 316

All working pressures are based on ANSI B31.3 304.1/3B. Allowable stress is based on the lowest of the following
criteria:
Tensile
Yield 2
Delta t =

Delta t =
3
3

195
kg/m
NOK/m
5 SCH 10
141.30 x 3.40
330114130340
58
66
248
11.56
5 SCH 40
141.30 x 6.55
330114130655
112
127
477
22.10
5 SCH 80
141.30 x 9.53
330114130953
162
184
695
31.40
5 SCH 160
141.30 x 15.88
3301141301588
271
307
1158
49.11
5 SCH xxs
141.30 x 19.05
3301141301905
325
368
1389
57.43
6 SCH 5
168.30 x 2.77
330116830277
40
45
170
11.47
6 SCH 10
168.30 x 3.40
330116830340
47
55
208
14.04
6 SCH 40
168.30 x 7.11
330116830711
102
115
435
28.69
6 SCH 80
168.30 x 10.97
3301168301097
157
178
671
43.21
6 SCH 120
168.30 x 14.27
3301168301427
204
231
873
54.10
6 SCH 160
168.30 x 18.26
3301168301826
261
296
1118
67.56
6 SCH xxs
168.30 x 21.95
3301168302195
314
356
1343
79.22
8 SCH 10
219.10 x 3.76
330121910376
41
47
177
19.97
8 SCH 40
219.10 x 8.18
330121910818
90
102
385
43.20
8 SCH 80
219.10 x 12.70
3301219101270
140
158
597
66.02
8 SCH 120
219.10 x 18.26
3301219101826
201
228
858
90.30
8 SCH 160
219.10 x 23.01
3301219102301
253
287
1082
111.30
8 SCH xxs
219.10 x 22.00
3301219102200
242
274
1034
107.00
10 SCH 40
273.00 x 9.27
330127300927
82
93
350
60.40
10 SCH 80
273.00 x 15.06
3301273001506
133
151
568
95.90
10 SCH 160
273.00 x 28.58
3301273002858
252
286
1078
171.90
10 SCH xxs
273.00 x 25.40
3301273002540
224
254
958
101.90
12 SCH STD
323.90 x 9.53
330132390953
71
80
303
73.90
12 SCH 40
323.90 x 10.31
3301323901031
77
87
328
79.70
12 SCH 80
323.90 x 17.45
3301323901745
130
147
555
131.90
12 SCH 160
323.90 x 33.32
3301323903332
248
281
1060
238.80
14 SCH STD
355.60 x 9.53
330135560953
81.30
14 SCH 40
355.60 x 11.13
3301355601113
94.50
14 SCH 80
355.60 x 19.05
3301355601905
158.10
14 SCH 160
355.60 x 35.71
3301355603571
281.70
16 SCH STD
406.40 x 9.53
330140640963
93.30
16 SCH 40
406.40 x 12.70
3301406401270
123.30
16 SCH 80
406.40 x 21.41
3301406402141
203.30
16 SCH 160
406.40 x 40.46
3301406404046
365.10
18 SCH STD
457.40 x 9.53
330145740953
105.20
18 SCH 40
457.40 x 14.27
3301457401427
155.80
18 SCH 80
457.40 x 23.80
3301457402380
254.20
18 SCH 160
457.40 x 45.24
3301457404524
459.40
20 SCH STD
508.00 x 9.53
330150800953
117.10
20 SCH 40
508.00 x 15.06
3301508001506
183.10
20 SCH 80
508.00 x 26.19
3301508002619
311.20
20 SCH 160
508.00 x 49.99
3301508004999
564.10
24 SCH STD
609.00 x 9.53
330160900953
140.90
24 SCH 40
609.00 x 17.45
3301609001745
254.60
24 SCH 80
609.00 x 30.94
3301609003094
441.00
24 SCH 160
609.00 x 59.51
3301609005951
806.50
VALVES
*3
BITE TYPE
FITTINGS
B.P. bar
*2
SAE J514 JIC

FLARE FITTINGS
W.P. bar
*1
HOSES &
HOSE COUPLINGS
ID Code
ADAPTORS
O.D x W.T
OTHER
COMPONENTS
Nom. pipe size

NPS x SCH Size
P= Pressure Mpa
MACHINES
*1: Bending and production

tolerances included.
*2: Production tolerances
included
*3: Burst pressure based
on Tensile value.
Not included tolerance of
wall thickness.
P x D
2 x Delta t
TECHNICAL
INFORMATION
t0 =
CLAMPS
ASTM A 312 TP 316 Pipe: Yield = 234 MPa, Tensile = 515 MPa. Allowable stress Delta t 156 MPa.
Yield and tensile based on material certificate from GS-Hydro.
_ 12.5% of wall thickness
b = 0.1333t0
Tolerances are +
TUBES & PIPES
TUBES & PIPES
GS-PRODUCTS
TUBES & PIPES

TUBES & PIPES
196
CLAMPS
VALVES
O.D x W.T
Oil flow capacity of tubing l/min
Pressure loss in tube bar/m
BITE TYPE
FITTINGS
SAE J514 JIC
FLARE FITTINGS
HOSES &
HOSE COUPLINGS
ADAPTORS
OTHER
COMPONENTS
MACHINES
TECHNICAL
INFORMATION
4,5 m/s
7,2 m/s
4,5 m/s
7,2 m/s
6 x 1.0
3.4
5.4
1.9
4.1
6 x 1.5
1.9
3.0
2.8
5.9
8 x 1.0
7.5
12.1
1.1
2.3
8 x 1.5
5.2
8.4
1.4
3.0
8 x 2.0
5.4
3.4
1.9
4.1
8 x 2.5
1.9
3.0
2.8
5.9
10 x 1.0
13.5
21.5
0.7
1.6
10 x 1.5
10.3
16.5
0.9
1.9
10 x 2.0
7.5
12.1
1.1
2.3
10 x 2.5
5.2
8.4
1.4
3.0
12 x 1.5
17.0
27.3
0.6
1.3
12 x 2.0
13.5
21.5
0.7
1.6
12 x 2.5
10.3
16.5
0.9
1.9
14 x 1.5
25.5
40.8
0.5
1.0
14 x 2.0
21.0
33.7
0.5
1.2
15 x 1.5
30.3
48.0
0.4
0.9
15 x 2.0
25.5
40.8
0.5
1.0
16 x 1.5
36.0
57.0
0.4
0.8
16 x 2.0
30.0
49.0
0.4
0.9
16 x 2.5
26.0
41.0
0.5
1.0
16 x 3.0
21.0
34.0
0.5
1.2
18 x 1.5
47.0
76.0
0.3
0.7
18 x 2.0
41.0
66.0
0.3
0.7
20 x 2.0
54.0
86.0
0.3
0.7
20 x 2.5
47.0
76.0
0.3
0.7
20 x 3.0
41.0
66.0
0.3
0.7
20 x 4.0
30.0
49.0
0.4
0.9
22 x 1.5
76.0
122.0
0.2
0.5
22 x 2.0
68.0
109.0
0.2
0.5
22 x 2.5
61.0
99.0
0.3
0.6
25 x 2.0
93.0
149.0
0.2
0.4
25 x 2.5
84.0
135.0
0.2
0.5
25 x 3.0
76.0
122.0
0.2
0.5
25 x 4.0
61.0
98.0
0.3
0.6
28 x 2.0
121.0
194.0
0.2
0.4
28 x 2.5
112.0
178.0
0.2
0.4
28 x 3.0
102.0
163.0
0.2
0.4
30 x 2.0
142.0
227.0
0.1
0.3
30 x 3.0
121.0
194.0
0.1
0.4
30 x 4.0
102.0
163.0
0.1
0.4
203.0
324.0
0.1
0.3
35 x 3.0
177.0
283.0
0.1
0.3
38 x 2.5
230.0
367.0
0.1
0.2
38 x 3.0
215.0
343.0
0.1
0.3
38 x 4.0
190.0
303.0
0.1
0.3
38 x 5.0
165.0
264.0
0.1
0.3
35 x 2.0
1,8 m/s
81.0
1,8 m/s
0.024
Continue next page
GS-PRODUCTS
BITE TYPE
FITTINGS
VALVES
CLAMPS
197
TUBES & PIPES
TUBES & PIPES
7,2 m/s
305
485
0.018
0.09
0.20
42 x 3.0
273
435
0.10
0.20
42 x 4.0
248
388
0.10
0.20
46 x 8.5
179
286
0.06
0.14
408
652
0.07
0.17
50 x 5.0
337
540
0.08
0.19
56 x 8.5
321
513
0.09
0.19
60 x 3.0
615
983
0.06
0.13
60 x 5.0
527
843
0.06
0.14
65 x 8.0
596
810
0.06
0.14
66 x 8.5
506
810
0.06
0.14
1004
1606
0.04
0.09
75 x 5.0
890
1453
0.03
0.10
80 x 10.0
759
1215
0.05
0.11
1453
2324
0.03
0.07
90 x 5.0
1349
2159
0.03
0.08
97 x 12.0
1124
1798
0.04
0.09
2414
3863
0.02
0.05
115 x 15.0
1524
3438
0.03
0.07
130 x 15.0
2109
3374
0.03
0.06
3619
5790
0.02
0.04
3037
4859
0.02
0.05
5060
8106
4800
7700
9122
14597
8500
13500
14980
24000
50 x 3.0
75 x 3.0
90 x 3.5
115 x 4.0
140 x 4.5
163
402
581
966
1448
150 x 15.0
165 x 5.0
2027
190 x 20.0
220 x 6.0
3469
250 x 25.0
273 x 6.0
5990
0.012
0.012
0.008
0.006
0.004
0.004
0.002
0.002
0.002
0.01
0.03
0.01
0.03
0.01
0.02
0.01
0.02
0.01
0.02
All calculation are based on Cold Drawn Tube DIN 2391 C/DIN 2445(EN 10305-4), viscosity 37 sct. specific gravities
0.860. If you desire to use different velocities than those stated above, use the following formula to determine the required
pipe size.
TUBE I.D = 4.61
HOSES &
HOSE COUPLINGS
4,5 m/s
121
42 x 2.0
ADAPTORS
1,8 m/s
OTHER
COMPONENTS
7,2 m/s
SAE J514 JIC

FLARE FITTINGS
Pressure loss in tube bar/m
4,5 m/s
MACHINES
Oil flow capacity of tubing l/min

1,8 m/s
Flow l/min
Velocity m/s
TECHNICAL
INFORMATION
O.D x W.T
GS-PRODUCTS
TUBES & PIPES

Multicore Tubes
TUBES & PIPES
198
CLAMPS
General Information
GS-Hydros multicore tubes are used for pneumatic and hydraulic remote control,
measuring and monitoring systems. In addition to the multicore tubes, GS-Hydro also
supplies the necessary connection tools and accessories such as heat shrinkable
products, tube joint fittings, tube cutter and bending tools as well as trays, supports
and binding tape for installation.
VALVES
Colored identifying inner sheath

Tube
Filler
BITE TYPE
FITTINGS
PVC Rod
Outer Sheath
The multicore tube consists of one to nine

stainless steel, copper or copper-alloy tubes
SAE J514 JIC

FLARE FITTINGS
laid up spirally inside an extruded outer PVC

sheath. For easy identification and protection
purposes each individual tube is PVC sheathed
in a different color. The extruded outersheath is
HOSES &
HOSE COUPLINGS
made of oil and sea water resistant, weatherproof,
flame-retardant,
corrosion
and
acid
resistant PVC. The multicore tube (outer sheath)

is continuously marked at every one meter
throughout the entire length for easy installation.
Heat shrinkable products provide complete water
ADAPTORS
sealing and abrasion and corrosion protection

under all conditions.
OTHER
COMPONENTS
MACHINES
TECHNICAL
INFORMATION
GS-PRODUCTS
199
Technical Data
Bare tube
Sheathed single tube
Multicore tube
Materials
Stainless steel AISI 304/316/316L

Copper
Copper-Nickel
Length
Standard 100300 m, up to 600 m packed on wooden drum
Tube diameter
615 mm (1/41/2)
Tube wall thickness
0.52.0 mm
No. of tubes per bundle
19 (max. 9core)
Outer sheath
PVC, black color with marking
Individual tube sheath
PVC, color identification
BITE TYPE
FITTINGS
VALVES
Tube type
TUBES & PIPES
Multicore Tubes
CLAMPS
TUBES & PIPES
All tubing products are certified by major classification

SAE J514 JIC
FLARE FITTINGS
agencies including DnV, GL, ABS, LRS and BV etc. The

multicore tubes are extensively tested, including eddy
current, tensile and hardness, hydro and air pressure and
OTHER
COMPONENTS
ADAPTORS
HOSES &
HOSE COUPLINGS
air leak tests.
MACHINES
Schematic Structural Diagram
3CORE
4CORE
5CORE
6CORE
7CORE
8CORE
9CORE
TECHNICAL
INFORMATION
1CORE 2CORE
GS-PRODUCTS
TUBES & PIPES

Multicore Tubes
TUBES & PIPES
200
Installation and Assembly
CLAMPS
The installation of the multicore tubes - the uncoiling from
connector, penetration gland etc. are utilised for
the wooden shipping drum, straightening, running and
connection or termination of the tube. Multicore tubes
cutting is done in the same manner as when installing
can also be welded but the use of bite type fittings is
electrical cables.
recommended.
VALVES
The multicore tubes are uncoiled directly from sturdy
Repeated bending at the same point should be
wooden reels onto ladder, perforated or flat-bar (or eq.)
avoided in order to avoid breakage. Where there is a
trays. Deck and/or bulkhead penetrations are made by
possibility of expansion and/or contraction along the
either coaming or by appropriate penetration fittings.
line, proper provisions should be made for loops and
Suitable fittings such as straight union, male/female
curves along the tube line.
BITE TYPE
FITTINGS
6 Cores
1 Core
Heat-shrinkable boot
2 Cores
Union
SAE J514 JIC

FLARE FITTINGS
4 Cores
Bending radius approx: 8 x outer dia
HOSES &
HOSE COUPLINGS
Order Example
ADAPTORS
10 x 1 / 6 PVC / AISI316
OTHER
COMPONENTS
Core Size
O.D. x Wall Thickness
Number of Cores
Material of Outer Sheath
Material Quality Pipe
MACHINES
TECHNICAL
INFORMATION
GS-PRODUCTS
Multicore Tubes
201
Maximum allowable working pressure

The maximum allowable working pressure (bar) for stainless steel, copper and copper-n ickel multicore tubes are as
TUBES & PIPES
TUBES & PIPES
Seamed Stainless Steel Tube
Seamed Stainless Steel Tube
0.5
0.8
1.0
1.2
1.5
2.0
160
270
350
120
195
250
310
10
95
155
195
240
310
12
125
160
195
250
350
15
125
155
195
270
0.035
0.049
1/4
275
410
3/8
180
264
1/2
140
200
Copper Tube
Cu-Ni (90/10) Tube
0.8
1.0
1.2
O.D.
(in.)
120
150
180
W.T. (in.)
0.035
0.049
1/4
130
180
85
110
130
3/8
85
110
85
100
1/2
85
12
70
85
1.0
1.4
1.5
10
130
190
200
12
160
170
JIS
ASTM
DIN
STS 304
SUS 304
304
1.4301
STS 316
SUS 316
316
1.4401
STA 316L
SUS 316L
316L
1.4404
Copper
C1220
C1220
C12200
SF-Cu
Copper-Nickel (90/10)
C7060
C7060
C70600
CuNi10Fe1Mn
Sheath Material
Name
Material
Rod
PVC
Colored identifying sheath
PVC
Filler
Synthetic rubber
Outer sheath
PVC
Remark
Seawater and oil resistant.
Flame retardant (IEC 60332 flammability test
criteria) or halogem free (LDPE/HDPE)
ADAPTORS
Stainless Steel
KS
OTHER
COMPONENTS
National Standard
Material
MACHINES
Tube Material
TECHNICAL
INFORMATION
Materials
HOSES &
HOSE COUPLINGS
SAE J514 JIC

FLARE FITTINGS
8
10
Wall Thickness (mm)
O.D.
(mm)
BITE TYPE
FITTINGS
O.D.
(mm)
Wall Thickness (in.)
O.D.
(in.)
VALVES
Wall Thickness (mm)
O.D.
(mm)
Wall Thickness (mm)
CLAMPS
follows:
GS-PRODUCTS
TUBES & PIPES

Multicore Tubes
TUBES & PIPES
202
Technical Data Metric Sizes

Bundle Weight (kg/m)
CLAMPS
O.D. (mm)
x
Core
Stainless Steel
Copper & Copper alloy
Wall Thickness (mm)
Wall Thickness (mm)
Overall diameter
approx.
(mm)
VALVES
BITE TYPE
FITTINGS
SAE J514 JIC
FLARE FITTINGS
HOSES &
HOSE COUPLINGS
ADAPTORS
0.5
0.8
1.0
0.8
1.0
1.2
6x1
0.15
0.18
0.20
0.20
0.22
6x2
0.60
0.67
0.71
0.70
0.74
19
6x3
0.75
0.86
0.92
0.90
0.97
20
6x4
0.82
0.96
1.04
1.10
1.19
23
6x5
0.90
1.08
1.18
1.14
1.25
24
6x6
1.04
1.25
1.37
1.34
1.47
27
6x7
1.15
1.39
1.53
1.40
1.56
27
6x8
1.40
1.68
1.84
1.60
1.78
32
6x9
1.60
1.92
2.01
1.85
2.05
34
8x1
0.20
0.25
0.28
0.27
0.31
0.34
11
8x2
0.73
0.83
0.89
0.87
0.94
0.97
23
8x3
0.85
1.02
1.12
1.07
1.18
1.28
24
8x4
1.00
1.20
1.33
1.29
1.43
1.56
28
8x5
1.30
1.52
1.67
1.59
1.77
1.93
31
8x6
1.50
1.82
2.00
1.94
2.15
2.34
33
8x7
1.63
1.93
2.15
2.08
2.33
2.56
33
8x8
1.90
2.35
2.60
2.52
2.80
3.04
41
8x9
2.10
2.67
2.95
2.88
3.20
3.49
43
10 x 1
0.30
0.34
0.37
0.41
13
10 x 2
1.10
1.18
1.24
1.32
28
10 x 3
1.50
1.60
1.68
1.81
29
10 x 4
1.80
1.97
2.09
2.26
33
10 x 5
2.00
2.20
2.33
2.55
37
10 x 6
2.15
2.40
2.57
2.83
40
10 x 7
2.28
2.52
2.80
3.10
40
10 x 8
2.95
3.20
3.60
3.95
48
10 x 9
3.30
3.80
4.15
4.54
51
12 x 1
0.36
0.41
0.39
0.45
15
12 x 2
1.38
1.42
1.44
1.50
33
12 x 3
1.81
1.96
1.91
2.08
38
12 x 4
2.13
2.37
2.26
2.53
39
12 x 5
2.44
2.70
40
12 x 6
2.70
3.00
48
OTHER
COMPONENTS
PVC Sheathed Tube Weight (kg/m)

O.D. (mm)
x
Core
Stainless Steel
Wall Thickness (mm)
Wall Thickness (mm)
Overall diameter
approx.
(mm)
1.0
1.2
1.5
2.0
1.0
1.2
10 x 1
0.34
0.38
0.43
0.51
0.37
0.41
13
12 x 1
0.41
0.46
0.53
0.63
0.44
0.49
15
15 x 1
0.52
0.58
0.67
0.56
0.63
18
MACHINES
TECHNICAL
INFORMATION
GS-PRODUCTS
Multicore Tubes
203
Technical Data Imperial Sizes

Bundle Weight (kg/m)
Wall Thickness
Overall diameter
approx.
(mm)
0.035
1.0 mm
0.049
1.2 mm
0.035
0.049
1/4 x 1
0.20
0.21
0.24
0.24
0.21
0.26
1/4 x 2
0.75
0.77
0.83
0.81
0.78
0.87
23
1/4 x 3
1.00
1.04
1.12
1.10
1.04
1.18
23
1/4 x 4
1.10
1.15
1.26
1.28
1.16
1.34
24
1/4 x 5
1.20
1.26
1.40
1.36
1.27
1.50
27
1/4 x 6
1.40
1.47
1.64
1.60
1.49
1.76
34
3/8 x 1
0.32
0.34
0.38
0.37
0.34
0.41
13
3/8 x 2
1.14
1.18
1.27
1.25
1.18
1.33
27
3/8 x 3
1.55
1.62
1.75
1.72
1.62
1.84
28
3/8 x 4
1.90
1.98
2.16
2.12
1.99
2.28
33
3/8 x 5
2.15
2.25
2.48
2.43
2.26
2.63
37
3/8 x 6
2.35
2.47
2.74
2.68
2.47
2.86
39
1/2 x 1
0.42
0.48
0.47
0.52
16
1.36
1.49
1.48
1.57
36
1.97
1.94
1.92
2.06
38
1/2 x 4
2.32
2.70
2.65
2.85
43
Tools and Accessories

Tools and accessories include heat shrinkable products, tube joint fittings, tube cutter and bending tools as well as trays,
supports and binding tape.
Accessories
ADAPTORS
Tools
HOSES &
HOSE COUPLINGS
SAE J514 JIC

FLARE FITTINGS
1/2 x 2
1/2 x 3
CLAMPS
Wall Thickness
VALVES
Stainless Steel
BITE TYPE
FITTINGS
O.D. (in.)
x
Core
TUBES & PIPES
TUBES & PIPES
Bending tools
Heat shrinkable products
Tube fittings
Clamps
Binding tape
Multicore tube bending tools
Multicore tube, tray and support
TECHNICAL
INFORMATION
MACHINES
OTHER
COMPONENTS
Tube cutter

Hydraulic Tubes and Pipes

Uploaded by

Copyright:

Available Formats

Hydraulic Tubes and Pipes

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hydraulic Tubes and Pipes

Uploaded by

Copyright:

Available Formats

What types of pipes and tubes are discussed in the document?

What types of pipes and tubes are discussed in the document?

What information is provided about stainless steel and carbon steel pipes/tubes?

What information is provided about stainless steel and carbon steel pipes/tubes?

H

SAE 6000 PSI

TUBES & PIPES

AISI 316 L Stainless Steel Tube

E 355N Hydraulic Tube (St52.4)

E 235N Hydraulic Tube (St37.4)

Hydraulic Tubes With Blue Passivation

Pipe to ANSI B36.19 1/2 4

Pipe to ANSI B36.19 5 24

Oil Flow Capacity and Pressure Loss

Installation and Assembly, Order Example

Maximum Working Pressure, Materials

Metric Size Tubes

Imperial Size Tubes, Tools and Accessories

SAE 6000 PSI

DIN 350-400 BAR

TUBES & PIPES

TUBES & PIPES

TUBES & PIPES

Stainless Steel (mm)

Stainless Steel (sch)

ASTM A269/A213 (A.W.)

tubes due to quality (precision in dimension and shape) and

from the marking GS Piping.

cleanliness reasons (no scale) As a comparison hot rolled

In order to ensure quality and traceability GS-Hydro can

deliver the pipes and tubes with either EN-10204.3.1.B

to the manufacturing process; by cold forming there will

or EN-10204.3.1.C certificates (in accordance with EU

not be any scale inside the tube after the manufacturing.

standard EN 10204 (DIN 50049)). The required certificate,

All precision steel pipes are supplied with trace numbers.

if any, has to be specified by the purchaser.

Stainless steel pipes & tubes

in AISI316L seamless quality from 6 mm to 80 mm O.D.

316L can be supplied with EN - 10204.3.1.B certificate

(=Outer Diameter). Larger O.D. tubes are supplied upon

upon request. The tubes are supplied at a standard length

special order. Seamless cold drawn stainless steel tube

of 6 m. All tubes are supplied plugged with plastic caps.

Tubes up to an O.D. of 75 mm can be supplied electric

tube according to DIN 2391C(EN 10305-4) O.D. x W.T.

zinc plated + yellow passivated or blue passivated (Cr VI-

DIN 1630ST52.4(E 355 N). High tensile strength tube

free alternative) for additional corrosion protection. As all

means higher permissible working pressures and reduced

original GS-Hydto tubes are marked with trace numbers

wall thickness, leading to reduced overall weight. GS-Hydro

the tubes can be supplied with certificates in accordance to

also stocks DIN 2391C(EN 10305-4) O.D. x W.T. DIN

EN 10204.3.1.B, if requested. Cerfitication according to EN

1630ST37.4(E 235 N).

10204.3.1.C is also available upon request. The tubes are

Tubes are supplied in an annealed condition and are

supplied at a standard length of 6 m up to 97 mm. Larger