WRING HARNESS - Troubleshooting

WRING

HARNESS

8-21 NBWUB

TROUBLESHOOTING
The most important point in troubleshooting is to determine Probable Causes. Once the probable causes are determined, parts to be checked can be limited to those associated with such probable causes. Therefore, unnecessary checks can be eliminated. The determination of the probable causes must be based on a theory and be supported by facts and must not be based on intuition only.

TROUBLESHOOTING STEPS
If an attempt is made to solve a problem without going through correct steps for troubleshooting, the problem symptoms could become more complicated, resulting in failure to determine the causes correctly and making incorrect repairs-The four steps below should be followed in troubleshooting. , Observation Symptoms of Problem Observe the symptom other problems. carefully. Check if there are also

II
3 3

Determination

of Probable

CSUSeS

In determining the probable causes, it is necessary to check the wiring diagram to understand the circuit as a system. Knowledge of switches, relays and other parts is necessary for accurate determination. The causes of similar problems in the past must be taken into account.

Checking of with Probable Determination

Parts Associated Causes and of Faultv Parts.

Troubleshooting is carried out by making step by step checks until the true cause is found. Always go through the procedures considering what check is to be made where for the best results.

Repair

and Confirmation

After the problems are corrected, be sure to check that the system operates correctly. Also check that new problems have not been caused by the repair.

INFORMATION FOR DIAGNOSIS This manual contains the cable diagrams as well as the individual circuit drawings, operational explanations, and troubleshooting hints for each component required to facilitate the task of troubleshooting. The information is compiled in the following manner: (I) Cable diagrams show the connector positions, etc., on the actual vehicle as well as the harness path. (2) Circuit drawings show the configuration of the circuit with all switches in their normal positions. (3) Operational explanations include circuit drawings of voltage flow when the switch is operated and how the component operates in reaction. (4) Troubleshooting hints include numerous examples of problems which might occur, traced backward in a common-sense manner to the origin of the trouble. Problems whose origins may not be found in this manner are pursued through the various system circuits. Remarks Components of ECI, ETACS. ECS. etc. with ECU do not include 3 and 4 above. For this information, refer to a manual which includes details of these components.

1 TSB Revision

8-22

WRING HARNESS - Troubleshootina INSPECTION

1. Visual and aural checks Check relay operation, blower motor rotation, light illumination, etc. visually or aurally. The flow of current is invisible but can be checked by the operation of the parts,

2.

Simple checks For example, if 3 headlight does not come on and a faulty fuse or poor grounding is suspected, replace the fuse with a new one or ground the light to the body by a jumper wire to deter mine which part is responsible for the problem.

3.

0 C " 50

Checking with instruments Use and appropriate instrument in an adequate range and read the indication correctly. You must have sufficient knowledge and experience to handle instruments correctly.

[@

Changeover

knob

INSPECTION lNSTRUMENTS
In inspection, make use of the following instruments. 1. Test lamps A test lamp consists of a 12 V bulb and lead wires. used to check voltages or shortcircuits.

It is

2.

Self-power test light A self-power test light consists of bulb, battery and lead wires connected in series. It is used to check continuity or grounding.

WRING HARNESS - Troubleshooting

8-23

3. Jumper wire A jumper wire is used to close an open circuit. Never use one to connect a power supply directly to a load.

4.

Black lead wire

Voltmeter A voltmeter is used to measure the circuit voltage. Normally, the positive (red lead) probe is applied to the point of voltage measurement and the negative (black lead) probe to the body ground.

5. Ohmmeter An ohmmeter is used to check continuity or measure resistance of a switch or coil. If the measuring range has been changed, the zero point must be adjusted before measurement.

Normal OFF

oDen (NO) me ON

CHECKING SWITCHES
In a circuit diagram, a switch is represented by a symbol and in the idle state. 1. Normal open or normal close switch Switches are classified into those which make the circuit open and those which make the circuit closed when off.
flows

---oh ax
hrrent does not flow Current
I

Normal close (NC) tYPe OFF ON

Current flows

---oo--I
CAX
Current does not flov
16so**, /

evision

a-24

WIRING HARNESS - Troubleshooting

2. SWITCH CONNECTION This figure illustrates a complex switch. The switch plates indicated by solid lines move in the direction of the arrow when operated. The continuity between terminals at each position is as indicated in the table below.

NOTE
O-O denotes continuity between terminals.

ltEEii
1 4 2 3 5 6
16W008

I
Coil Iron piece

Cover Spring Iron core Contact

CHECKING RELAYS
1. When current flows through the coil of a relay, its core is magnetized to attract the iron piece, closing (ON) the contact at the tip of the iron piece. When the coil current is turned off, the iron piece is made to return to its original position by a spring, opening the contact (OFF).

Ed z. e

1660231

k.&. Relay

2.

By using a relay, a heavy current can by turned on and off by a switch of small capacity. For example, in the circuit shown here, when the switch is turned on (closed), current flows to the coil of the relay. Then, its contact is turned on (closed) and the light comes on. The current flowing at this time to the switch is the relay coil current only and is very small.

&E Em

I
I

16BO232

Normal ooen IN01 tvoe 1 Deeneroized staae 1 Enernized stage

1 ED:
IX
Current does not

3. The relays may be classified into the normal open type and the normal close type by their contact construction. NOTE
The deenergized state means that no current is flowing g-

1 : 4

through current

the coil and the energized is flowing through the coil.

state

means

that

g:. BP:=

Current flows

1660233

prevision

WIRING HARNESS - Troubleshootinn

Normal close (NC) type Deenergized stage ( Energized stage

1 : ED=
4

IX
Current flows Current do& not flow 166023.

When a normal close type relay as illustrated here is checked, there should be continuity between terminals (I) and (2) and between terminals 3 and 4 when the relay is deenergized, and the continuity should be lost between terminals 3 and 4 when the battery voltage is applied to the terminals 1 and 2. A relay can be checked in this manner and it cannot be determined if a relay is okay or faulty by checking its state only when it is deenergized (or energized).

CHECKING FUSES
A blade type fuse has test taps provided to allow checking of the fuse itself without removing it from the fuse block. The fuse is okay if the test light comes on when its one lead is connected to the test taps (one at a time) and the other lead is grounded. (Change the ignition switch position adequately so that the fuse circuit becomes live.)
1600236

State of fuse blown

due to overcurrent

CAUTIONS IN EVENT OF BLOWN FUSE

When a fuse is blown, there are two probable causes as follows: One is that it is blown due to flow of current exceeding its rating. The other is that it is blown due to repeated on/off current flowing through it. Which of the two causes is responsible can be easily determined by visual check as described below. (I) Fuse blown due to current exceeding rating The illustration shown the state of a fuse blown due to this cause. In this case, do not replace the fuse with a new one hastily since a current heavy enough to blow the fuse has flowed through it. First, check the circuit for shorting and check for abnormal electric parts. Only after the correction of such shorting or parts, fuse of the same capacity should be used as a replacement. Never use a fuse of lager capacity than the one that has blown. If such a fuse is used, electric parts or wirings could be damaged before the fuse blows in the event an overcurrent occurs again.

166023,

State of fuse blown

due to thermal

fatigue

(2) Fuse blown due to repeated current on/off The illustration shown the state of a fuse blown due to repeated current on/off. Normally, this type. of problem occurs after fairly long period of use and hence is less frequent than the above type. In this case, you may simply replace with a new fuse of the same capacity.

1660236

TSB Revision

WIRING HARNESS - Troubleshooting CHECKING CABLES AND WIRES

1. Check connections for looseness, rust and stains. 2. Check terminals and wires for corrosion by battery electrolyte, etc. 3. Check terminals and wires for open circuit or impending open circuit. 4. Check wire insulation and coating for damage, cracks and degrading. 5. Check conductive parts of terminals for contact with other metallic parts (vehicle body and other parts). 6. Check grounding parts to verify that there is complete continuity between attaching bolt(s) and vehicle body. 7. Check for incorrect wiring. 8. Check that wirings are so clamped as to prevent contact with sharp corners of the vehicle body, etc. or hot parts (exhaust manifold, pipe, etc.). 9. Check that wirings are clamped firmly to secure enough clearance from the fan pulley, fan belt and other rotating or moving parts. 10. Check that the wirings between the fixed parts such as the vehicle body and the vibrating parts such as the engine are made with adequate allowance for vibrations.

HANDLING ON-VEHICLE BAlTERY

When checking or servicing does not require power from the on vehicle battery, be sure to disconnect the cable from the battery (-) terminal. This is to prevent problems that could be caused by shorting of the circuit. Disconnect the (-) terminal first and reconnect it last. Caution 1. Before connecting or disconnecting the negative cable, be sure to turn off the ignition switch and the lighting switch. (lf this is not done, there is the possibility of semiconductor parts being damaged.) 2. After completion of the work steps [when the batterys negative (-1 terminal is connected], warm up the engine and allow it to idle for approximately five minutes under the conditions described below, in order to stabilize engine control conditions, and then check to be sure that the idling is satisfactory. For 3.OL Engine models: lf the engine rpm is high, switch OFF the ignition switch, and then, after switching it ON again, let the engine idle for 2 or 3 minutes. This will cause the engine rpm to decrease about 100 rpm, so repeat this procedure until the prescribed idling speed is reached. Engine coolant temperature: 8595C (185203F) Lights, accessories: OFF Transmission: neutral position (Automatic transmission models: N or P). Steering wheel: neutral (center) position

1 TSB Revision

WIRING HARNESS - Troubleshooting TROUBiiSHOOTlNG

Power supply

8-27

FLEX3

Motor

A circuit consists of the power supply, switch, relay, load, ground, etc. There are various methods to check a circuit including an overall check, voltage check, shortcircuit check and continuity check. Each of these methods is briefly described in the following. 1. VOLTAGE CHECK (I) Ground one lead wire of the test light. If a voltmeter is used instead of the test light, ground the grounding side lead wire. (2) Connect the other lead wire of the test light to the power side terminal of the connector 0. The test light should come on or the voltmeter should indicate a voltage. (3) Then, connect the test light or voltmeter to the connector 0. The test light should not come on, or the voltmeter should indicate no voltage. When the switch is turned on in this state, the test light should come on, or the voltmeter should indicate a voltage, with the motor starting to run. (4) The circuit illustrated here is normal but if there is any problem such as the motor failing to run, check voltages beginning at the connector nearest to the motor unit the faulty part is identified.

2.
Power supply

CHECKING FOR A SHORT-CIRCUIT Because the fuse has blown, it is probable that there is a shot-t-circuited circuit. Follow the procedures below to narrow down the short-circuit location.

illumination light 3
16AOSC

kEE NEXT PAGE/

evision I

8-28
Power supply

WIRING

HARNESS

- Troubleshooting
FROM I / Switch ON the (The test light illuminates but the illumination light does not.1 \ PREVIOUS PAGE

CONTINUED

Disconnect

the load

Illumination iii T

light
16AO6~

NO

Power supply Test light

Fuse block (Remove the fuse.)

Switch ON l ~ -

Disconnect

the load

Short-circuit location illumination light

t T

1610504

I
Self power test light (or ohmmeter) Switch

3.

CHECKING CONTINUITY (1) When the switch is in the OFF position, the self power test light should come on or the ohmmeter should read 0 LI only when the terminals 2 and 3 are interconnected. (2) When the switch is in the ON position, the self power test light should come on or the ohmmeter should read 0 R only when the terminals 1 and 4 are interconnected.

I TSB

Revision

WJRJNG HARNESS - How to Read Wiring Diagrams

8-29

HOW TO READ WIRING DIAGRAMS

HOW TO READ CONFIGURATION DIAGRAMS
(1) Connector symbols A wiring diagram shows the installed condition of each connector in a schematic style. The connectors are shown and classified as follows, depending on their locations and are marked by connector symbols. In case connectors of the same shape (same number of wires) are centralized, their colors are indicated for identification. Example: A-52 T (Black) ;~;;~I;;~;,, Connectors unrque number (serial number)

-PET

A, B : Engine compartment C : Instrument panel D : Interior and frame

;Main

fusible

link oil

4WD indicator switch A-05 Automatic transmission temperature switch t wiring diagram

and ihe circuit diagram.

Indicates color of the A-52 connector.

I I st5 nevwon I

~~

--

8-30

WIRING

HARNESS

- How to Read Wiring Diagrams

(2) Identification of connectors differing according to different vehicle specifications Without wiring harness connectors, the inter-device or-wiring harness connectors which van/ in shape or position on different vehicle specifications are given the specificationdependent connector identification symbol (lower case alphabet) after a serial number. For detailed information on this specification-dependent symbol, refer to Item (8) under HOW TO READ CIRCUIT DIAGRAMS. (3) Indication of standard mounting positions of harnesses The standard mounting positions of harnesses are shown with the mark * in wiring harness configuration diagrams. (4) Indication of ground point The position of ground points are shown in wiring harness configuration diagrams. For detailed information on the ground portion, refer to ELECTRICAL SYSTEM PARTS LOCATION (Grounding).

Refer to item (3)

Ground symbol -A

t4
Refer to item (4) ITSB Revision

WIRING HARNESS - How to Read Wiring Diagrams HOW TO READ CIRCUIT DIAGRAMS

831

The circuit diagrams are functionally separated. (1) indication of circuit connected to another circuit When the circuit in a circuit diagram connected to another circuit in a different diagram the page number of that different diagram is indicated so that it can be referred to. (2) Indication of device connections The circuit diagram shows whether a device harness connection is one with an attached cable or is a direct connection type. (3) Indication of connectors in circuit diagrams A connector in a circuit diagram is shown in a frame and is assigned a connector symbol. This symbol corresponds to the symbol in a wiring harness configuration diagram so that the connector location can be known easilv. An intermediate connector has its female side oniv shown as a rule. However both of the male and female sides are shown when they differ in wiringcolor.

Refer to Item (2) If a frame showing a connector touches the symbol of a device, it indicates that the device harness connection is a direct connection type.

B-36

I
H 1

22-RL 1-8-39

I B I u

i2-RL 18

I ----------------____ ----______ --

On a circuit connected Indicates that this connector is a B-39

to another

the circuit is connected and pages on which diagrams of such another circuit

TSB Revision

8-32

WIRING

HARNESS

- How to Read Wiring Diagrams

(4) indication of fuses, fusible links and centralized relays The fuses and fusible links ina circuit diagram are indicated by a wave symbol (-1 and a double wave symbol (-), respectively. At a centralized junction, the fuses are given fuse numbers and centralized relays are given connector symbols. Example of centralized junction symbol: A-01 X -L_T Centralized junction Connectors unique Connector symbol indication symbol number (serial number)

(5) Indication of ground point The ground point in a circuit diagram is marked by a ground symbol, making it possible for to a wiring harness configuration diagram and to ELECTRICAL SYSTEM PARTS (Grounding). (6) indication of wires In a circuit diagram, the wire diameter and wire color are shown for each wire. If there wires of the same color in a connector, their wire color indication symbols should be such *I and *2 for identification.
Refer to Item (4). On connectors like this one aiven a centralized junction identificaiion symbol (X), refer to CENTRALIZED JUNCTION for connector shaoe. etc.

you to refer LOCATION are several symbols as

I
I
rr

--:*:on

switch

Dome light

A-16X

------------_I-~ ----------------e-39

BRL l ,
l!LEiE

,rw0*~

l2 z
Refer to Item (6) The connector B-39 has two wires identical color (RL). so they are given identification symbols l l and 2 in order to distinguish
them.

in

1 TSB Revision

.-

WIRING HARNESS - How to Read Wiring Diagrams

8-33

(7) indication of shielded cables A shielded cable used, for example, in an electronic control circuit for prevention of malfunctions that may otherwise ------ caused by radio interference be is indicated by a solid line sandwiched between dashed lines (-=I. (8) Indication of specification-dependent connectors With regard to harness connectors, the inter-device and harness connectors which vary in shape or position on different vehicle specifications, such as those with rear wipers and turbocharger and those without turbocharger, are given a specificationdependent connector identification symbol (lower case alphabet) following the connector symbol. Example: A-Ola T Specification - dependent connector identification a : Vehicles with auto-cruise control b : Vehicles without auto-cruise control c : Vehicles with a power window d : Vehicles without a power window symbol

(9) Shapes of connectors The connector shapes are indicated by simplified symbolic marks. female connectors, refer to HOW TO DENTIP/ CONNECTORS.

For distinction

between

male and

Refer to Item (8) The b at the end of the connector symbol is a specification-dependent connector identification symbol and indicates that the connector is used for vehicles without auto-cruise control.

TSB Revision

8-34

WIRING HARNESS - How to Read Wiring Diagrams IDENTIFYING CONNECTORS

Position of guide to prevent improper connection I In circuit diagrams, the connectors are indicated by symbolic marks which show the number of their wires and whether they are male or female connectors. (I) Number of connector wires The number of divisions in the connector diagram indicates the number of wires. A cross in a division, however, indicates- the position of a guide to prevent improper connection. The connector shown here, therefore, is a g-wire connector. (2) Identification of male and female connectors Connectors drawn with double outer lines are male, and those with single outer lines are female.

g-wire

connector

1680219

Male terminal

Female terminal

On-vehicle B

connector

Connector in wiring diagram

(3) Connector direction The connector marks show on-vehicle viewed from the direction shown here.

connectors

as

1 @~~co,or I
I / code
Guide to prevent

(4) Identification of connector terminals The color codes of a -pair of connectors (male and female), if viewed at their joining surfaces, will appear symmetrical as illustrated here. When the connectors are connected, their joining surfaces are put together in the way a book is closed so the terminals of identical codes are connected together. NOTE The color codes of male and female connectors are not always identical. (5) Identification of sealed connectors Identification of round, sealed connectors (water-proof pin terminal connectors) used in radiator fan motor circuits, turbo circuits, etc. is accomplished by the same method as described above.

connection

improper

Dgs indicate male.

NumberS?ions indicates number

of wires

WIRING HARNESS - How to Read Wiring Diagrams SYMBOLIC MARKS

Various
Battery
l

8-35

equipment

is indicated
Body ground

symbolically
Single hub

in circuit diagrams
Resistor

as shown

below.
Diode
Capacitor 1

El Fuse Kso Equipment ground ariai

b resik&r Zener dii

Fusible link

Motor

Speaker

Coil

Transistor

WRE COLOR CODES

Wire colors are identified
Example: 1.25 - GB

by the following

color codes.
Zode 1 B 1 1
1

(
~G

Wire color Black Brown Green Grav Blue Light green

I Code / I ! LI 0 / I

Wire color Light blue Orange Pink Red I

L
G:

Br Gr

1 / I

F
(1) (2)

B:

1.25: Wire size (mm) F: Flexible wire T: Twisted wire

~
L kl

1 1

Yellow White I

1 w

No code indicates 0.5 mm LOO08 in?). Cable color code in patantheses indicates 0.3 mm2 LOO05 in.).

NOTE If a cable has two colors the first of the two color code characters indicates the basic color (color of the cable coating) and the second indicates the marking color.

TSB

Revision

8-36
<2.6L Engine>

WIRING HARNESS - Overall Wiring Diagram

OVERALL WIRING DIAGRAM

Frame wirin8 i harness : harness

Roof wiring Center aanel wirina harness

harness

Back door wiring /

I wiring 4WD indicator Remark This diagram shows the main wining harness wiring harness

harness

<3.OL Engine> P-door vehicles

Roof wiring ymess

Frame wiring i /

harness Back door wiring harness te \ \/ hamess

A
Front wiring Center pane wiring h*harness A \ \ Battery cable (+) // \

Transmission

wiring

harness

Door wiring

harness

(L.H.)

4WD indicatdr Remark This diagram -

wiring

harness

.~

shows the main wiring

harnesses.

: TSB Revision

WIRING ~3.01 Engine> 4-door vehicles

HARNESS

- Overall Wiring Diagram

8-37

Licence Roof wiring harness (Vehicle? not equipped with a sunroof) I

plate

Roof wiring harness (Vehicles with a sunroof)

Back door wiring

harness I

Control

wiring

hames

amess Rear door wiring ion wiring wiring harness harness (L.H.)

wiring

harness

Engine control wiri 4WD Indicator

lSW16SO

harness

Remarks (I) This diagram shows the main wiring harnesses. (2) The dotted line (....) is applicable to models equipped with the dual air conditioner system.

TSB Revision

WRING HARNESS - Engine Compartment

c2.6L Engine>

ENGINE COMPARTMENT <2.6L Engine>

A-02 A-03

A-52 t-0; Main fusible link A.03}4WD indicator switch $$} Back-up light switch A-06 Pulse generator A-07 4WD indicator wiring harness and transmission wirina harness combination A-08 Air conditioner solenoid valve A-09 Front wiper motor i:jy] Starter A-12 Engine coolant temperature gauge unit A-l 3 Checker A-14 Brake fluid level sensor A-l 5 Front wiring harness and fusible link combination

A-51 A-26 Condenser fan motor relay A-27 Headlight washer motor A-28 Front combination fight (L.H.1 i$}Light control relay A-31 Dedicated fuse (Upper beam indicator circuit) A32 Headlight (L.H.) A-33 Condenser fan motor A-541

A-l 6 Front wiring harness and 4WD indicator wiring harness combination A-17 Front wiring harness and fusible link combination iI:i)Sub fusible link A-26 Carburetor assembly A-21 Control wiring harness and air conditioner wiringharness combination A-22 Front wiring harness and control winno harness combination A-23 Devi& box A-24 Auto choke relay A-25 Front wiring harness and air conditioner wiring tiamess combination

1 TSB Revision

WIRING HARNESS - Engine Compartment <2.6L Engine>

839

A-38 ig Ignition coil A-41 I A-42 Magnetic clutch Alternator E.2 A45 Engine coolant temperature A-48 Engine coolant temperature circuit) A-47 Oil pressure gauge unit flt$ Oxygen sensor Asr,} Low pressure switch

A37

A-35

A-51 A-52 AS3 A-54

Headlight (R.H.) Front wiring harness and air conditioner Front combination light (R.H.) Front washer motor

wiring

harness

sensor switch

(FBC circuit) (Air conditioner

Remarks (1) The mark * shows the reference mounting position of wiring harness. (2) For information concerning the ground points (example: 0). refer to P.8-12.

1 TSB Revision

840

WIRING HARNESS - Engine Compartment

<3.OL Engine>
By3
B-:0 B-T2 %: B-115 0-;17

ENGINE COMPARTMENT <3.OL Engine>

B-04 \ E-03 B-02 I

Pc z-v E3-06 -r\

B-07 \

B-09 \ B-l,\ \ i-s\-,

1 B-1? 1 I I

\\\

\I

B-01 \

Front wiring harness and battery cable (+) combination Ei}Altemator B-04 Noise condenser LC filter El B-07 Idle speed control motor B-08 Throttle position sensor B-09 Distributor signal generator B-10 Front wiring harness and engine control wirino harness combination B-11 Power transtitor B-12 Engine coolant temperature,switch B-,3 (Overdrive control system crrcult) B-,4 14WD indicator switch B-15 EGR temperature sensor <California> B-16 I nition coil B-17 8 D-OFF solenoid

B-01

uF
B-62

~~~B-36 Headli ht washer B-37 Auto c7 oke relay

B-5i 1 550 B-4

B-18 Pulse generator B-19 Oxygen sensor B-20 4WD indicator wiring harness and transmission wiring harness combination B-21 Back-up light switch (Vehicles with a manual transmission) 4WD indicator wiring harness and automatic transmission wiring harness combination (Vehicles with an automatic transmission) B-22 Front wiper motor B-23 Control wiring harness and fusible B-24 I link B-25 Checker 526 Brake fluid level sensor

B-27 Diode B-28 Front washer motor B-29 Control wiring harness and 4WD indicator wiring harness oombination B-30 Front wiring harness and 4WD indicator wiring harness combination B-31 Pu e control solenoid valve B-32 EG# control solenoid valve B-33 Magnetic clutch B-34 Actuator B-35 Front wiring harness and air conditioner wirino harness c;&bikati;n---.-= ..-...--motor

WIRING HARNESS - Engine Compartment <3.OL Engine>

841

B-19 B-18 t B-20

B-21 /B-22 B;23 3;25

-B-38

-B-39 BS91 f33yjlnjector B-82 Headlight (R.H.1 B-83 Fmnt combination light (R.H.) B-84 Front wiring harness and air conditioner wiring harness combination Eg} Low pressure switch B-87 Fmnt wiring harness and control B-88 I wiring harness combination B-89 Power steering oil pressure switch B-70 Air flow s(enso? i:$}Sub fusiblme link B-73 Condense r fan motor (Dual air conditioner) B-74 Sub condenser fan motor (Dual air conditioner) mounting position of

Dedicated fuse (Upper beam indicator circuit) B-39 Front combination light (L.H.) i$} Light control relay B42 Headlight (L.H.) B-43 Condenser fan motor or air conditioner wiring harness and air conditioner wiring harness combination E 646 Hom 8-47 / 848 Condenser

B-38

649 55:

Injector

B-52 Engine coolant temperature gauge unit B-53 Engine coolant temperature switch (Overdrive control system circuit) coolant temperature sensor B-54 Engine 1 (MPI circuit) 865 Engine coolant temperature switch (Air conditioner circuit) Bemarks B-56 Oil pressure gauge unit (1) The mark * shows the reference

iz,} Sta tier

fan motor relay 1 TSB Revision ?\ \L,

wiring harness.
For information concerning 0). refer to P.814. i the ground points (example

._

-i

WIRING HARNESS - instrument Panel

8-42

INSTRUMENT PANEL
c-91 c-02 C-03 c-04 C-05 C-06 C-07 C-08 GO9

031 C-02 C-03 C-04 C9:

Defog erswitch Back 8 oor lock switch Key reminder and seat belt warning buzzer I Combination meter

Voltage meter C-17 Heater control C-18 %$er switch C-19 Air conditioner c-u) C-21 C-22 C-23 C-24 C-25

E13

knob illumination switch illumination

C-97 Diode C-08 Hazard switch C-09 Rear wiper and washer switch ~~~}Oil pressure gauge C-l 2 fihTbination gauge illumination C-l 3 Combination gauge wiring harness and front wiring harness combination C-14 Combination gauge illumination light Remarks For information refer to P.813,

$jht ower switch (Air conditioner circuit) Heater relay Air conditioner wiring harness and front wiring harness combination Air conditioner relay A Dedicated fuse (Air conditioner rim tit\ circuit) Air conditioner relay B
. --, .,

-E$}Thermostat C-28 Self-diagnosis check connector C-29 Front wrring harness and roof wiring harness combination C-30 Automatic free-wheeling hub indicator control unit C-31 Front wiring harness and control wiring harness combination ~ C-32 Defogger timer unit c-33 OPOFF relay Intermittent rear wiper relay Ei )Fmnt wiring harness and door C-36 wiring harness (R.H.) combination c-37 MPI control relay C-38 Auto-cruise control unit

concerning 15.

the ground

points

(examplem). I

TSR

Rtavisinn

WRING HARNESS - instrument

G12 c-14

Panel

8-43

28 /

C-38

c-85

c-84

SW650

Feed back carburetor control unit or MPI control unit C-42 Fuel pump drive tem+nal G43 Blower motor resistor G44 Front speaker (R.H.) C-45 Air conditioner switch G46 Clock C-47 Heater control panel illumination G48 g:tray illumination light C-49 Spare terminal C&C) p5: Cigarette lighter rllumrnation CS2}Qgarette lighter $$}Radio G55 Shift position illumination light

light

Inhibitor switch OD-OFF switch Door lock control relay Door lock power relay Parking brake switch Seat belt switch Front wiring harness and center panel wiring harness combination zz}Column switch C-65 Column switch (Auto-cruise system circuit) g; p$~m~y-ctch C-68 Stop light switch/Brake C-59 Clutch switch switch

C66 C-57 C-58 G59 C-60 C-61 G62

C-73 C-74 C-75 C-76 C-77 C-78 C-79 C80 Cal C82 C83 C-84 G85

wiring harness and door harness (L.H.) combination Turn-signal flasher unit Power window relay Intermittent wiper relay Hazard flasher unit Headlight washer motor relay Seat belt warning timer Front speaker (L.H.) Dimmer cantml switch Dedicated fuse (Central locking system circuit) Dedicated fuse (Sunroof circuit) Front wiring harness and roof wiring harness combination (Sunroof circuit) Dedicated fuse (Dual air conditioner circuit) Front wiring harness and air

conditioner wiring harness

combination circuit) (Dual air conditioner

TSB Revision

-~~-

e-Ef

8-44

WIRING HARNESS - Interior

and Frame <4-door

Vehicles>

INTERIOR AND FRAME <4-door Vehicles >

ET :I Yr-g;: g.giiEf~ EL--

D-01 D-02 D-03 D-04 E-0;

Power window motor Power window sub switch Door lock actuator Dome light Door swatch (R.H.)

Dq7}Rear speaker (R.H.) D-08 Defogger (-) D-09 Defogger (t) D-l 0 Rear wiper motor D-l 1 Back door wiring harness and license plate light wiring harness combination D-12 Back door wiring harness and defogger cable (+) combination D-13 Rear washer motor D-14 Rear side marker Ught (R.H.) D-15 Frame wiring harness and back door wiring harness D-1 6)combination D-17 Rear combination light (R.H.) ~~~}License plate light (R.H.) k$y}License plate light (L.H.) D-22 Back door lock actuator D-23 Rear side marker light (L.H.) D-24 Fuel pump (MPI) D-25 Rear combination light (L.H.) D-26 Fuel gauge unit Egi Front wiring harness and frame wrring combination D-29 I E$}Rear speaker (L.H.) D-42 Sunroof switch D-43 Sunroof control relay D-44 Front wiring harness and rear door wiring harness D-45 1(R.H.) combination D-46 Power window sub switch D-47 Power window motor D-48 Door lock actuator D-49 Dome light (rear) D-!?O Door switch-(rear R.H.) DSl Frame wirins harness and side wiiing harness (R.H.1 combination
I

harness

E:sg}Door switch (L.H.) D-34 Door lock actuator D-35 Power window control relay D-36 Power window main switch D-37 Power window motor D-38 Sunroof power relay D-39 Dome light <Vehicles with the sunroof> D-40 Sunroof motor D-41 Roof wiring harness and sunroof wiring harness combination
I TSRRmh&m

_;

WRING HARNESS - Interior and Frame CCdoor Vehicles>

8-45

D-17

D-63

1 D-61 1 D-62 D-60

D-54

D-53 \ D-25 \D-22 D-23

36w343

;:g D-29

D-52 Rear evaporator assembly D-53 Frame wiring harness and side wiring harness (L.H.1 combination D-54 Frame wiring harness and rear washer wirin harness combination <Vehicles with the %ual air conditioneo D-55 Rear washer motor <Vehicles with the dual air conditioneo D-56 & conditioner relay D (Dual air conditioner circuit) D-57 Air conditioner relay E (Dual air conditioner circuit1 D-58 Frame wiring harness and air conditioner wiring harness combination D-59 Door switch (rear L.H.)

D-60 Door lock actuator D-61 Blower switch (Dual air conditioner circuit) D-62 Power window motor D-63 Power window sub switch D-641Front wirina harness and rear door wiring harness D-65 [(L.H.) com&ation

Remark The mark * shows the reference wiring harness.

mounting

position of

TSB Revision

846

WIRING HARNESS - Interior

and Frame <Z-door

Vehicles>

INTERIOR AND FRAME <2-door Vehicles>

Power window motor Power window sub switch Door lock actuator Dome light Door swatch (R.H.1 Rear speaker (R.H.) Defogger (-1 Defogger (+) Rear wiper motor Back door wiring harness and license plate light wiring harness combination D-12 Back door wiring harness and defogger cable (+) combination D-13 Rear washer motor D-14 Rear side marker light (R.H.) D-15 Frame wiring harness and back door wiring harness D-l 61 combination D-17 Rear combination light (R.H.) ki,}License plate light (R.H.) ksy}License plate light (L.H.)

D-01 D-02 D-03 D-04 fg po7) D-08 D-09 D-10 D-l 1

O-22 Back door lock actuator D-23 Rear side marker liaht (L.H.1 D-24 Fuel pump (MPI) and frame wiring kzy}Rear speaker (L.H.) harness

Remark c;zs;k

* shows the reference

mounting

position

of wiring

I TSE

Ravisian

WRING HARNESS - Starting Circuit

8-47

1 STARTING CIRCUIT
<Vehicles with a Manual Transmission>

Ignition switch

pin Battery

fusible

Sub fusible link

Starter

Remark (1) Lines and connectors indicated by the * symbol are applicable to the 2.6-liter models. (2) The broken line (----) is applicable to the 3X-liter models only. (3) For information concerning the ground points (example: 0). refer to PI?-12, 14. Wiring color code B: Black Br: Brown LI: Light blue 0: Orange G: Green P: Pink L: Blue Y: Yellow

1 TSB Revision

8-48

WRING HARNESS - Starting Circuit

<Vehicles with an Automatic

Transmission>

Id
0-72

Sub fusible (IGN. SW)

link

ignition

switch

5-wm5-w

0.85-R

1-1 I

fsmw I
I

B-71 Main fusible

Inhibitor switch

Starter
37W666

Remark For information concerning refer to P.&l 4. Wiring color code B: Black Br: Brown LI: Light blue 0: Orange

the ground

points (example:

q ),
L: Blue Y: Yellow

G: Green P: Pink

WRING

HARNESS

- Ignition Circuit

8-49

2 IGNITION CIRCUIT
<26L Engine>

Ignition switch /T-Y

C-66

To !eed back rzzzi~ camuretor control unit [Refer to P.8-621

Capacitor

Ignition

coil

q am

(g 88
67W67-2

Remark For information concerning refer to P.&l 2. Wiring color code B: Black Br: Brown LI: Light blue 0: Orange

the ground

points (example:

II),

G: Green P: Pink

Gr: Gray R: Red

L: Blue Y: Yellow

Lg: Light green

W: White

[ TSB Revision

8-50
<3.OL Engine>

WIRING

HARNESS

- Ignition

Circuit

Ignition

switch

OFF

C-66 Main. fuslote

To multipurpose

fuse e3-BW

To combination meter PTACHO) [Refer to P.8-821

lB+
&
B
I Distributor

e -~ ;
c I

Power transistor

a H 0
F%ilEl B MJ

Ignition coil

q
Remark For information concerning the ground point (example: q ), refer to P.8-14. Fr$cFlor code Br: Brown G: Green ;;:,:y LI: Light blue 0: Orange P: Pink

Capacitor @ m

LC filter I!3 s,we*s

L: Blue Y: Yellow

Lg: Light green W: White

WIRING

HARNESS

Charging

Circuit

8-51
Ignition switch

3 CHARGING CIRCUIT

IG

?k Alternator

To light 22

Z-BW --

.. Multi-

WB c3.OL Engine onlv>

RL I w I I I .
I I I I I I I I

I
Choke relay Combination meter *

Auto choke relay l-+-l

Remark (1) The broken line (----) and connectors indicated by the * sympol are applicable to the 2.~liter models (2) z;,cha[n lme (- - -) IS applicable to 3.0-liter models (3) For information concerning 0). refer to P.8-12, 14. the ground points (example:

37w71a

Wiring color code B: Black Br: Brown LI: tight blue 0: Orange

G: Green
P: Pink

$,y

L: Blue
Y: Yellow

1 TSB Revision

8-52

WIRING

HARNESS

- Feed Back Carburetor

Circuit

4 FEED BACK CARBURETOR CIRCUIT

Main fusible !4

M 15-w

Sub fusible

link

Ignition

switch

I
S:
A-19 [

OFF CC
C-66

To alternator [Refer to P.&51 .I * A-24

o*85-w To multi-purpose fuse 4

I cu

2BRE 2IRL )
2-BW

Feed back solenoid valve

Slow cut solenoid valve

hrottle positior snsor

.G YR
.GY
(I) For ~~en.$io.oyceming the ground points (example:

Carburetor

assembly

PI F- e symbols

0, @ etc. indicate that the wiring is connected (using the same numerical symbol) to the facing page. (In other words, Q) on the right page is connected to @ On the left page.)

1 TSB Revision

WIRING

HARNESS

- Feed Back Carburetor Circuit

8-53

lgnitior I coil

q
*&2-BW

tics c *~

2 P

z
4, To vacuum solenoid valve [Refer to P.8104.1

El

A-3

Feed back carburetor control unit

I I I 4

1 Vacuum

switch

1 Device box

control solenoid

sensor sensor

1 TSB Revision

8-54

WIRING HARNESS - Layout of Components

(F.B.C.)

LAYOUT OF COMPONENTS
Items

(F.B.C.)
Symbol Items Symbol I I D A 1 -1 E F

I Auto choke relay I Engine coolant temperature I I Feed back solenoid

1 Oxygen sensor valve

I
sensor I I I

J
B G K

I Secondary

air control solenoid valve

I Slow-cut solenoid valve Throttle opener control solenoid valve (for the air conditioner) position sensor

1 Engine speed sensor (Ignition coil) Feed back carburetor control unit

I c I Throttle
1 H

1 Vacuum switch

/ TSB Revision

WIRING HARNESS - Layout of Components (F.B.C.)

8-55

Throttle posiiion sensor TTPS)

SFUl

) TSB Revision

8-56 5 M.P.I. CIRCUIT

Main fusible link

WIRING HARNESS - M.P.I. Circuit

1 [Refer to P.8-47.48.1 83

Combination meter

Air flow s*nsor

1 TSB Revision

WIRING HARNESS - Overdrive Control System Circuit

Inhibitor I

switch I

Engine coolant teFp?rature

Diode

II-i&

OD-OFF relay

B-27

-iarm-rm

RL

To back-up light [Refer to P.8-88.1

011 (p &

YR (Lg)

I 1 7

I I

OD-OFF switch @jig

Automatic transmission oil temperature switch InC

OD-OFF solenoid

37w683

Wiring color code B: Black Br: Brown LI: Light blue 0: Orange

G: Green P: Pink

L: Blue Y: Yellow

Lg: tight green W: White

1 TSB Revision

8-62

WIRING

HARNESS

- Auto-Cruise

Control System Circuit

7 AUTO-CRUISE

CONTROL SYSTEM ClRClJlT

Sub fusible link

ignition

switch

IN

ACC

Stoplightswitch, brake switch

To inhibitor switch [Refer to P8-48.1 (AJTj To starter relay (M/T) [Refer to P.847.1

I
z 1
To over drive relay [Refer to P&60.]

0.85-G To hazard switch [Refer to P.S.72.1 e

Remarks (1) For details on the ground point (No. q in the illustration). refer to P.&14. (2) In the illustration, the numbered wiring on the right hand paae corresponds to the numberina on the left hand hand page corresponds Wire color code B: Black Br: Brown LI: Light blue 0: Orange to @ on the left

1.85-RL

To turn si nal flasher [Refer to 8 .8-72.1

unit

G: Green P: Pink

g;:,t;y

L: Blue Y: Yellow

Lg: Light green W: White

WIRING HARNESS - Auto-Cruise Control System Circuit

8-63

(Reed switch) Self-diagnosis check

BY B

To automatic free-wheeling hub indicator control unit [Refer to P.8-85.1

BLBgGY l-l

l 1

) TSB Revision

8-64

WIRING HARNESS - Headlight Circuit

8 HEADLIGHT CIRCUIT
Engine>
D^a&^-, /yl$n fusible , Sub fusible link

Ignition

switch

- . . , , I .. u
A-18

I m

I I

B
*I * Combination meter I r I

Aa,
Dedicated fuse

2-Bqlm

A-51

Light control relay

-1

nnlnn
(L.H.) Headlight (R.H.)
37W660

Lighting switch

Dimmer switch

Passing switch-

Remark For information

concerning

the ground

points

(example:

81, refer to P.812.

14.

WIRING HARNESS ,: Headlight Circuit

8-65

<3.OL Engine>
pkin fusible

Ignition

switch

l-w

2-Wn3-W u
B-71 2-Bq,lfJij g l,p2-B

2-B4,10
0
IRI 83 B-38 Dedicated fuse l1.25-y

II
I

2-L

I2-L

m rii.
w geTeination

c multi-oumose mc fuse r-.C

w To

2-Bc#,~

4b

-_

Light control relay

Lighting switch

DirXrtTher Passin! switch Column switch

Headlight

,,,a,

pizcrlor LI: Light blue

code Br: Brown 0: Orange G: Green P: Pink $gY L: Blue Y: Yellow

1 TSB Revision

-;n__-*,

--

__I

~~

I: 8-66
WIRING HARNESS
Tail Light, Position Ucense slate tigti Light. Rear Side Marker and Back-Up tight circuit Light,

-~

<2.6L Engine>
Sub fusible link

OFF cc

To radio (Refer to PB-90.1

GW SL

[Refer to P.8-70.1

I-

I
-t
I

.co (GW) a e .o
ii:%
A-16

f
A-07

Back-up switch

light

Wiring color code 8: Black Br: Brown LI: Light blue 0: Orange

G: Green P: Pink

Gr: Gray R: Red

L: Blue Y: Yellow

Lg: Light green W: White

WRING HARNESS-

Tail tight

Position tight, Rear Side Marker tight, ticense Plate tight and Back-UpUght circuit

8-67

Column

switch Liaht control relav

F-GW nGW F-B 1 IB u

D-11

License plate light

CZI m

gg

(GWL-JGW) ;L IRG)
D-29

El RG
,c4c

Tail light

combination

Rear side marker light (L.H.) D-23

srwesz

( TSB Revision

-= ffi.i.

:pp

q:u

_ P

,~~

,._

8-68
<3.OL Engine>

WIRING HARNESS

Tail tight, Position ticense plate tight

Light, Rear and Back-Up

Side Marker Light ~ircuti

Light,

Sub fusible

link Ignition switch

OFF cc

To radio [Refer to PB-92.1

GW
G a cz T 24 % I I

To turn-signal flasher unit [Refer to P.6-72.1

0.85RL
T I I I ID\ D-@ GWh

1
) It
l

B-63

-66

Position
r--r

light
B-211

Inhibitor switch

Ba&p

light

Wiring color code B: Black Br: Brown LI: Light blue 0: Orange

G: Green P: Pink

L: Blue Y: Yellow

Lg: Light green V$ White

1 TSB Revision

WIRING HARNESS

Tail tight, Pasition license plate tight

light Rear Side Marker snd Sack-Up tight cir~ti

Light,

8-69

Column

switch

c-33

I I

A
(3 l-l D-11 D-21 U-H.)

License elate iight

El !zl

Tail light Back-up light Back-up light Tail light 1 ! WTaiI light

Rear combination #!z.,

ReeLI %zl
Rear combination $!E.,

Remarks (1) The broken lines are applicable to models equipped with an automatic transmission. (2) For information concerning the ground points (example: refer to P.&14. (3) R e symbols 0, Q etc. indicate that the wiring is connected (usrng the same numerical symbol) to the facing page. (In other words, @ on the right page is connected to @ on the left page.)

.
37W881

1 TSB Revision

8-70

WIRING

HARNESS

- Turn-Signal

and Hazard Light Circuit

10 TURN-SIGNAL
t2.6L Engine>

AND HAZARD LIGHT CIRCUIT

ignition

switch

Light control

relay

To radio [Refer to P.8-92.1

Turn-signal

and

km-s&y&end Front combination light 1R.H.)

car nbination combination

I-----

meter

WRING HARNESS - Turn-Signal and Hazard Light Circuit

M 0 en

Haz?rd Turn-signal I switch unit I r

Hazard switch I

-73

-76

-IA .
0

c-64

I I 1

-1

l
0

(BY) ! , , ,

Rear Combination light (R.H.)

light Dimmer switch control

Rear combination light (L.H.)

GL

GLIB
D-2 Remarks ~ . ,-. I I) For lntormatlon concernin tne ground (example: 0). refer to P. # -12. (2) The symbols 0, Q, etc. indicate that connected (uslng the same numerical facing page. (In other words, 0 on the right page h c. +&.n lnft non,3 \ points tbe wiring is symbol) to tht is connected tl

~r$jc$lor LI: Light blue

code

Br: Brown 0: Orange

G: Green P: Pink

1: Blue Y: Yellow

Lg: Light green W: White

/ TSB Revision

<3.OL Engine>
B-72 Sub fusible link

5-w 3-R I
Main fusible link CL

5-w-5-w u

0.85-R 1-1 I

3-w

EEEI

aw

ignition

swKch

I!Y

Light control relay Multi-purpose fuse

To radio [Refer to P.8-92.1

-GW

B-63

-04

I I bb

Al 1

Turn-signal and hazard light Front combination light (L.H.)

Turn-signal I. and I.--- d,. nazam agnr Front combination light (R.H.)

Combination ._ I I I w m

meter I I 0 I si

WIRING

HARNESS

- Turn-Signal

and Hazard Light Circuit

Hazard switch I I Turn-signal switch I

*I

rZ I

I I

II Illll

I I I

WR-

Turn-signal and hazard light

Rear Combination light (R.H.)

B _

Rear combination light (L.H.)

nemarks (1) For information concerning the ground points (example: J refer to P.8-14. (2) The symbo P- 0, Q, etc. indicate thatthe wiring is s connected (usrng the same numerical symbol) to the facing page. (In other words, 0 on the right page is connected to @ on the left page.) ~in&olor LI: Light blue code Br: Brown 0: Orange G: Green P: Pink ggy L: Blue Y: Yellow
37W686

/ TSB Revision

WIRING HARNESS - Stop Light Circuit

11 STOP LIGHT CIRCUIT

<2.6L Engine>

Multi-purpose

fuse 1

C-08

------jh

1 I

0.85-G ~I@*-" I

Hazard switch

L
0.85-WG
the ground points (example: G: Green P: Pink

Tumsignal switch

Stop light Rear combination light (L.H.)

Stop light Rear combination light (R.H.)

Remark For information refer to PS-12,

concerning 14.

Q).

Wiring color code B: Black Br: Brown 11: Light blue 0: Orange

L: Blue Y: Yellow

WIRING HARNESS - Stop Light Circuit

a-75

<3.OL Engine>

*1 +2

Sub fusible

link

B-88

3-w-3-w l-l
C-88b E yi Multi-purpose fuse QQ G88a

(I

I IT

I17
C-08

-0.85-G Efl1p-B
I

Hazard switch

/0.85-WG

I r
Tumsignal switch

II

;;0.85-WG I IWR I 11.11

ml ml
I I

,I

I LJ.

Stoplight Rear combination light (L.H.)

Stop light Rear combination light (R.H.)

37W676

1 TSB Revision

8-76

WRING HARNESS - Instrument

Panel

hminatipn

Circuit

12 INSTRUMENT
<2.6L Engine>

PANEL ILLUMINATION

CIRCUIT
Sub fusible link

fusible

link

Optical fiber

GW

I I

II

Lighting switch -46 Cigarette liohter ilGmination Heater control 13 Clock illumination illumination light

Ashtray illumination liaht

G Lsl!!l
I C-06 Dimmzl combination illi lmination light meter light ,&I

r
I

To radio [Refer to P.8-90.1

II

Rear Fwf;gJer illumination

switch

-g& ight& &

f-g-J

_ qg$

57W677

Remarks (1) The broken lines are applicable to models equipped with an automatic transmission. (2) For information concerning the ground points (example: 0). refer to P.8-12, 14.

I I St5 newton

WIRING HARNESS - Instrument Panel Illumination Circuit

8-77

<3.OL Engine>

fusible

fink

Optical

fiber

I IAL

contml knob illumination light

Heater control

knob

io to P.8-92.1 Lb

Din Irnx Combination meter illumination light light illumination light light illumination light

switch

Wiring LI: tight

color code

B: Black
blue

Br: Brown
0: Orange

L: Blue Y: Yellow

WIRING HARNESS - Dome Light Circuit

13 DOME LIGHT CIRCUIT

<tdoor Vehicles>

PI t-4 1
To light control $f?er Combination meter to P.8-54, 65

Dome light

(L.H.)

(R.H.)
37W7!24

Door switch Remarks (1) The broken line (----) and fusible link indicated %ssymbol are appkcable to M-liter models. 2.tNiter (2) Tim;d;Fn line (- - - - -) is applicable to 3.0-liter Tim;d;k? by the

(3) Chain lines (---(-;-) and lines indicated by the Q symbol are applicable to models equipped with the sun ;yoyboI roof. .--.. (4) For information concerning the ground points (example: a). refer to P.572. 14. Wiring color code Br: Brown B: Black LI: Light blue 0: Orange G: Green P: Pink

WRING HARNESS - Dome Light Circuit

al-door

Vehicles>
Main R El

13-R

B-m 3-Rn3-R I

1.25-GB

To hazard flasher unit [Refer to P.S-70, 72.1

B
RGn
D-32 Front door switch (R.H.)

El
RG

E: switch

Front dome light (models not equipped with

Front dome light (models equipped with the sunroof)

D-49

To sunroof switch [Refer to P.8113.]

37W662

/ TSB

Revision

8-80 14 METER CIRCUIT

WRING

HARNESS

- Meter Circuit

ignition
-

switch

Battery

Main fusible link

I

Sub fusible link

Multi-purpose 5

fuse

To seat belt warning timer [Refer to P.6-64.1 To seat belt warning buzzer [Refer to P.6-64.1 Toalternator [Referto P.851.1 3 dimmer, passitig. Nitch and light control !lay [Refer to P.6-64.1

To door L^switch-,n 1 rD^T^n n

Combination

meter

WIRING HARNESS - Meter Circuit

8-81

Wiring color code 0: Black Br: Brown LI: Light blue 0: Orange L: Blue Y: Yellow Eli Oil pressure gauge unit

G: Green P: Pink

El
4WD indicator El ,r,\
I I -1 , t dl , _ IT , ,.OF0)

switch

A-14

Parkh;g brake

ypgy 1
BI IB

Fuel gauge unit

&

Engine coolant temperature gauge unit I3

Combinati on gauge

, l!h!z!J
C-l 4

iii

For information concerning the ground points (example: ) refer to PS-12. (2) The symbo $* 0, Q, etc. indicate that the wiring s is connected (usina the same numerical svmboll to the facing page(In other words, @) on the right page is connected to 0 on the left page.)

8-82
<3.OL Engine>

WIRING

HARNESS

- Meter Circuit

Sub fusible

link

El33

nw

Ignition

switch

B-68

3-R m3-R u Al
To light control relay [Refer to P&65.]

3 CA &!I
N B-71

OFF ACC

Multi-purpose

fuse

To turn-signal switch [Refer to P.872.1 To seat belt warning timer [Refer to P.8-641 buzzer [Refer to P. To alternator [Refer to P.8-51 o dimmer. oassina witch and-light co>tl clay [Refer to P.8-65.1 To dome liaht [Refer to P&78.1 To door switch [Refer to P.878.17

C III II
II I I I I

1111

I I

I,
Urii

Ill I I I
iii

II I 1
ii

II II
I

I I II
Ii

I
I

,1 I T)c ,I .lLzP, D I I ,a,-@ I I I ILYIC@

) IWL/B

I I VI *kh

1 TSB Revision

WlRlNG

HARNESS

- Meter Circuit

8-83

g$y Oil pressure gauge unit

L: Blue Y: Yellow

Lg: Light green W: White G: Green P: Pink

Wiring color code B: Black Br: Brown 0: Orange LI: Light blue

El
switch IFI

Engine coolant temperature gauge unit

Ei

M.P.I%&unit

1
Combination gauge

Remarks (1) For information concerning the ground points 1). refer to P.8-14. i 0, Q, etc. indicate that the wiring lected (using the same numerical symbol) Facing page. I (In otht x words,-@ on the right page is connec :ted to @ on the left page.1

TSB Revision

8-84

WIRING HARNESS - Buzzer Circuit

15 BUZZER CIRCUIT
Sub fusible link Ignition switch

To light control relay d [Refer to P.6-64. 65.1

3-R

12 - R

To hazard flasher unit 1.25-GB [Refer to P.670. 72.1 4

Key reminder switch

Front door switch (L.H.)

-04

switch Key reminder and seat belt warning buzzer

Seat belt warning timer

Remarks (I) Broken lines and lines indicated by the x( symbol are aonlicable to the 2.6liter models. (2) The chain line f- - - - -) is applicable to 30litermodels. (3) For information concerning the ground points (example: gJ), refer to P.B-12. 14. Wiring color code Br: Brown B: Black LI: Light blue 0: Orange G: Green P: Pink L: Blue Y: Yellow

RLL B ED RB

Lg: Light green W: White

I TSB Revision

WRING HARNESS - Automatic Free-Wheeling Hub Indicator System Circuit 8-85

16 AUTOMATIC CIRCUIT
Main fusible link

FREE-WHEELING HUB INDICATOR SYSTEM

Sub fusible linktgnluon swwn

0.85-R
11 -1 A-181 - i -1 J

3-w

1 1

[Refer to PB-102,

103.1

d I Liz d

Automatic free-wheeling indicator control unit

hub
37W723

Remarks (1) Lines and connectors indicated by the a symbol are applicable to the 2.8liter models. concerning the ground points (example: 0). refer to P.S-12, 14. (2) For information Wiring color code B: Black Br: Brown LI: Light blue 0: Orange G: Green P: Pink L: Blue Y: Yellow Lg: Light green W: White

1 TSB Revision

17 WIPER AND WASHER CIRCUIT

<2.6L

Light control relay

Intermittent

wiper

control

relay

Remarks (1) For information concernin the ground points (example: ii 1, refer 7 to P.8-12, P (2) The symbols Q, Q etc. indicate that the wiring IS connected (using the same numerical symbol) to the facing page. (In other words, @ on the right page is connected to @ on the left page.) Wiring cotor code 8: Black Br: Brown LI: Light blue 0: Orange G: Green P: Pink $:8%y TSR
Ravkinn

Headlight -washer motor

L Bl L.
L: Blue Y: Yellow Lg: Li ht green W: W 1 ite
I

Headlight washer motor relay

WIRING

HARNESS

- Wiper and Washer Circuit

8-87

Column switchFront wiper switch

-1
Rear wiper and washer switch

switch

ON OFF INT
I mI I

Lc-63

F-?/q-i
I I
k-64

-09

I I I I

D-l 0 AS4

Intermittent wiper relay

rear

F-washer motor

Front wiper motor

Rear washer motor

L----l-

Rear wiper motor

TSB Revision

8-88

WIRING

HARNESS

- Wiper

and

Washer

Circuit

<3.OL Engine>

L. I Hii3
Ignition switch

Light control relay

lemarks 1) The dotted line (....) is applicable to models equipped with the dual air conditioner system. 2) For information concernin the ground points (example: ii ), refer EL to P.814. 3) The symbols Q, Q. etc. indicate c: that the wiring IS connected (using the same numerical symbol) to the facing page. (In other words, 1 on the right 1 page is connecte 9 to @ on the left page.) Niring color code 3: Black Br: Brown _I: Light blue 0: Orange G: Green P: Pink ;;:Ptry L: Blue Y: Yellow

Headlight washer motor

Lg: Light green W: White

Headlight washer motor relay

I TSB Revision

-.=

WIRING HARNESS - Wiper and Washer Circuit

8-89

---

Column

swit_ch -1 switch
1

Front wiper 1 Headlight 1 washer I switch

I

I I IFront wasier

I I :A
flFFim=

.I

Rear wiper and washer switch

ON OFF
INT

HI

@L 0.85-L

2-B

Intermittent wiper relay

rear

Frontwasher motor

Front wiper motor

motor

Rear wiper motor K

TSB Revision

WIRING HARNESS --Radio

/ Cassette Deck Circuit

Sub fusible link

lanition

switch

To light control relay [Refer to P&66.]

2-R

+-d

Z-RN 2-R

?i lA

To cigarette lighter [Refer to P.&94.1

It-r

To dimmer control swtch [Refer to P.6-76.1

DIN Cable

Tape player

Radio

1 TSR Revision

WIRING

HARNESS

Radio

/ Cassette

(R.H.)

,
Deck

Circuit

8-91

t Front speaker
(L.H.)

El El
Rear speaker El El

37W706

(qTm&?nformation concerning the ground points (example: (*) $f), refer to P.&l 2. e symbols 0, Q, etc. indicate that the wiring is connected (using the same numerical symbol) to the facing page. (In other words, @ on the right page is connected to @) on the left page.) Wiring color code B: Black Br: Brown LI: Light blue 0: Orange G: Green P: Pink L: Blue Y: Yellow Lg: Light green W: White

1 TSB Revision

8-92
C3.01 Engine>

WRING HARNESS - Radio / Cassette Deck Circuit

L. m
Sub fu$ble link

If-l

Ignition -

switch

To light control relay [Refer to P&68.]

. ._-.

.-

_.,

To Clock [Refer to P.894.1

To dimmer control [Refer to P.877.1

switch By

II

DIN Cable

l--l

Tape player

[ T$B Revision

WIRING HARNESS - Radio / Cassette Deck Circuit

8-93

* BR B
Front speaker

(L.H.)

El El
Rear speaker (2door vehicles) El El

YL F YR

YL YR

YL m GrL( ( u
D-53

(L.H.)

q El
Rear speaker &door vehicles) El El

D-28 p*fl
371705

(R.H.)

Remarks (1) For information concerning the ground points (example: refer to P.8-14. (2) w e symbols (i), Q, etc. indicate that the wiring is connected (using the same numerical symbol) to the facing page. (In other words, 0 on the right page is connected to @ on the left page.) y$cclor LI: tight blue code Br: Brown 0: Orange G: Green P: Pink g;:,pJ L: Blue Y: Yellow $f gf;eween

1 TSB Revision

8-94

WIRING

HARNESS

Ciaarette

Liahter

/ Clock

Circuit

19 ClGARElTE

LIGHTER / CLOCK CIRCUIT

L. , m
Ignition switch

;I;;
5-w 3:R
Main fusible link

Sub fusible

link

5-w r5-biZ

-1 Pi, 3-E

3-i' r-----------

an

AI

i,

, -~ 1

..-- - -71

iieGt0 To radio [Refer to P.590.

--.. _.-.relay

- *,,. ,
4 1 Z-R 12-R

P.8-66. 68.1

I 1

92.1
c L-K 1

To hazard flasher unit [Refer to PI?-70, 72.1

To dome light [Refer to P.8.78.)

lgarette lighter jmination fight

To heater control illumination light [Refer to P.8-76. 77.1

~~%broken line I----) and lines indicated bv * svmbol are aoolicable to 2.61iter .

[Refer to P.8-80. 82.1

niodels:

(2) The chain line (- - - - -) is applicable 3.~liter models. 13) For information concerning the ground (example: 0). refer to P.812. 14. Wiring color code Br: Brown B: Black LI: Light blue 0: Orange G: Green P: Pink

to points [Refer to P.&76.1

37W720

$:P:zy

L: Yellow y: Blue

g;

$y$-

1 TSB Revision

WIRING

HARNESS

- Defogger Circuit

8-95

20 DEFOGGER CIRCUIT
Sub fusible link

. 8. IilcEl
Ignition switch

z;n

fusible

Fusible link

To alternator [Refer to P.8-51 .I To light control relay ~ [Refer to P.8-66. 68.1

Z-RW
I

Defogger

+lEl

El

2-B

2-BR

m
D-l 2

2F-Bn3-B
D-l 5

:, :, a
d

%I

%I

(BYI

1 I

I I

Dimmer control switch uerogger umer unn

R I rZ cl -tlEE3- w LR I Remarks (1) The broken line (----) and lines indicated by the * symbol are applicable to 2.6liter (2) The chain line (- - - - -) is applicable to 3.0-liter models. (3) For information concerning the ground points (example: q ), refer to P.8-12. 14. Wiring color code B: Black Br: Brown LI: Light blue 0: Orange G: Green P: Pink $,,raY L: Blue Y: Yellow models.

Lg: Light green W: White

TSB Revision

8-96

WIRING

HARNESS

- Power Window

Circuit

21 POWER WINDOW
<bdoor Vehicles>

CIRCUIT

w l33

B.

.~

Ignition

switch

td

Sub fusible

link

~~

flasher unit [Refer to P.870. UP r-=-=-l DOWN * UP DOWN

72.1

1.25-B eo

@ 6 a9 0 03 I I I I

l.XF-S

1.25F-G/ 12-GL
c-71 D I. * 033 0

2-GLpo

Power window main switch

Remarks (1) For information

concerning the ground points (example:~). refer to P.812, 14. etc. indicate that the wiring is connected (using the same n-umerical on the right page is connected to @) on the left page.)

symbol)

to the facing page.

/ TSB Revision

WRING HARNESS - Power Window Circuit

8-97

R BD
Power window motor (L.H.)

Power window power relay

RI. BLI EI3

g:

(RL) Z-LR
Power window control relay

O41.25-B 1.25-GL 1.25-R 1.25-G @,r 1.25-L

1.25-RL 1.25 Power window motor (R.H.) 0 2-RL.-a F-G ?-LB. a T-L Z-GL. a --R CT5 Ai71 1

?-1,25-GL )+- 1.25-RW * 1.25-RL ;* 2-L 4 2-B ;- 2-RL a4 2-GL

-.

Power window sub switch (R.H.)

37wo5

Wiring color code B: Black Br: Brown LI: Light blue 0: Orange

G: Green P: Pink TSB Revision

Y: Yellow

L: Blue

Lg: Light green W: White .-

I.

8-98
:4-door Vehicles>

WIRING HARNESS - Power

Window

Circuit

ignition Sub fusible link

switch

txl

B G IRU~ lRLl1 v RIB/ LlGLlRY UP& -DOWN

Front power main switch UP-

window DOWN

1.25-RL J.Z5F-R >.25F-G 1.25F-R-2-RL 1,25F-G 2-GL 2-RL 2-GL3

l--p%-&
L B ED
emarks I) For details on the ground point (No.uin the illustration). refer-to P.&14. !) In the illustration. the numbered wiring on the right hand page corresponds to ( @ on the right hand page corresponds to @ on the left hand page. etc.1 the numbering on the leti hand page.

1 TSB Revision

WIRING

HARNESS

Power

Window

Circuit

8-99

Power window -

control

relay FFnt power y;dpw motor

(N-1
o,=Z-LR

amAD

LFa

Front power window sub switch (R.H.1

Rear pqwy wfnoow

l-3

4.25-RL

I
Rear power window sub switch (L.H.)

@,2-RL @.2-GL

ear power vvv;c&w sub Wiring color code 8: Black LI: Light blue Gr: Gray R: Red

Br: Brown 0: Orange L: Blue Y: yellow

G: Green P: Pink 8; #;ewen

37W666

TSB Revision

22 CENTRAL LOCKING SYSTEM CIRCUIT

Door lock control unit

0 Q 0 @I 0 @I

Door lock power relay

11

l 2 r3

1 TSB

Revision

WIRING

HARNESS

- Central Locking System Circuit

8-101

Front door lock actuator (L.H.) I I , (R.H.) ,

D-63~
,I l 2

D63d

C36c

C-36d

~ U-H.)
Rear door lock actuator <-door

(R.H.) vehicles>

37W664

/$m??details on the round point (No. q in the illustration), refer to P.812. 14. (2) In the illustration, t3, e numbered wiring on the right hand page corresponds to the numbering (0 on the right hand page correspon s to @ on the left hand page, etc.) Wire color code B: Black LI: Light blue Br: Brown 0: Orange G: Green P: Pink L: Blue Y: Yellow

on the left hand page.

!&$y

$j; $f$egreen

TSB Revision

8-102

WIRING

HARNESS

- Heater Circuit

23 HEATER CIRCUIT
<2.6L Engine>

. B. EEEI
lanition switch

Blower

Remark For information refer to P.812.

concerning 14.

L L. LA LI LI m
switch

Blower motor resistor w LI LR El3 I.. a),

Heater relay
37W713

the ground points (example:

Wiring color code 8: Black Br: Brown LI: Light blue 0: Orange

G: Green P: Pink

L: Blue Y: Yellow

1 TSB Revision

VVIRING HARNESS - Heater Circuit

<3.OL Engine>

8-103

C-4

k? Ml L
OFF
L

Blower

switch

3lower mot0 resistor La LI R ED L.

L I.. LR La I l5EEl

M
Revision

Blower motor

Heater rel

37w71s

TSB

8-104

WIRING HARNESS - Single Air Conditioner

Circuit

24 SINGLE AIR CONDITIONER

<2.6L Engine>

CIRCUIT
Ignition switch

IT

3-LK 1-Q

Multi-purpose fuse

To turn si nal flasher unit [Refer to B .8-70.1 I -I To ciaareit<a 1i%ii; to P.894.1 I I I I

0.85WB

A-l

~~
Blower switch

Blower motor resistor

Heater

relay

V&irin~cclor Li: Light blue

code Br: Brown 0: Orange

G: Green P: Pink
T-CR
Rnnirinn

L: Blue Y: Yellow

Lg: Light green W: White

WIRING HARNESS - Single Air Conditioner Circuit

8-105

Ak;;tditioner
- . . --.

Air conditioner Thermistor

relay B
I

Air w onditioner
,

relay A

Id

II& ,C -27

fxn

I -24

23

*I B. B. l 2 xl
A-52

I
l%zi

*20.B5-BWn0.85-F I I

Ada

Vacuum

solenoid

0.85-WB

I1

5 z d li

:
A-46

Engine coolant temperature switch COndenser blower motor Lonoenser orower motor relay

tT
378702

Magnetic clutch (compressor)

I3

(Rlym%%formation concerning the ground points (example: (1) 0). refer to P.612. (2) The symbols 0, Q, etc. indicate that the wiring is connected (usrng the same numerical symbol) to the facing page. (In other words, @ on the right page is connected to @ on the left page.)

1 TSB Revision

8-106
<3.OL Engine>

WIRING HARNESS - Single Air Conditioner

Circuit

OFF

To turn signal flasher [Refer to P.%72.1

unit

0.85-B

I I!Lr!d-LlJ!-

Blower motor

I Blower switch

L L. LR Eml-8LI

Blower mote: resistor

Heater relay

Wiring color code B: Black Br: Brown LI: Light blue 0: Orange

;i ,i,

L: Blue Y: Yellow

Lg: Light green W: White

1 TSB Revision

WIRING

HARNESS

Single

Air Conditioner

Circuit

8-107

Thermistor

@(3-LR

@-0.85-B 040.85-LW @>,0.85-WB

!
r
Condenser blower motor Condenser blower motor relay

-RW

c-40
M.P.I. control

Magnetic clutch (compressor)

37W708

Remarks (1) For information concerning the ground points (example: (1) 0). refer to P.8-14. 0 The symbols 0, @I, etc. indicate that the wiring is connected (uslng the same numerical symbol) to the facing page. (In other words, @ on the right page is connected to 0 on the left page.)

TSB Revision

~~

7.

~.

8-108

WIRING HARNESS - Dual Air Conditioner

Circuit

25 DUAL AIR CONDITIONER

CIRCUIT
r;l Ignition Iawl switch

Battery

ktbe

Main

q fill q l1
To turn si nal flasher [Refer to B .8-72.1 unit

H
M2 Ml

L OFF
Front blower -P switch Front blower resistor motor
l 1

l z

87w709

wa)

Wiring color code B: Black Br: Brown LI: Light blue 0: Orange

G: Green P: Pink

L: Blue Y: Yellow

1 TSB Revision

WIRING HARNESS - Dual Air Conditioner Circuit

8-109

-0.85-B &O.SS-LW

040.85-WB 0.85-BY ;BW

--Cl

c-40 BW

M.P.I. I .,

Magnetic clutch (compressor)

Condenserblower motor relay

te%~~~<~&witch fii@

@marks (I) For information concerning the ground points (example: II). refer to P.814. (2) The symbols 0, 0. etc. indicate that the wiringis connected (using the same numerical symbol) to the facing paQe. (In other words I on the ri ht page is connecte 9 to @ on t1 e left page.)

j TSf3 Revision

8-110

WIRING

HARNESS

- Back Door Lock Circuit

Magnetic valve -Rear blower motor Rear blower resis tor motor

A ,ir conditioner I

relay E I

D-57

Rear blower

switc h
37w703 13131

Condenser fan motor

~nb~oy~yse

D-56 Remark In the illustration, the numbered wiring on this page corresponds to the numbering on the previous page. (5 on this page corresponds to @ on the fir conditioner preoious iwe. etc.) relay D Wire color code B: Black Br: Brown G: Green L: Blue Lg: Li ht green Gr: Gray 3 LI: Light blue 0: Orange P: Pm Y: Yellow W: White R: Red -1

1 TSB

Rnvicinn

WIRING

HARNESS

- Back Door Lock Circuit

8-111

26 BACK DOOR LOCK CIRCUIT

Sub fusible link

1.25F-G 1.25F-R

,1.25-G 1.25-R
D-16 7: z: . .

+ 4

To heater relay [Refer to P.&l 02, 103.1

c3.OL Engine>.

4door pfq+q

vehicles& z,:

Q.6L c::

Engine>

M
b Back door lock actuator

37w712

Rennarks (1) Broken lines and line indicated

by the il symbol are applicable to the 2.6liter models. (2) The chain line (- - - - -) is applicable to 3.~liter models. concerning the ground points (example: 0). refer to (3) For information P.812, 14.

Wire color code B: Black Br: Brown

G: Green 4 P: Pm W: White

Gr: Gray
bl; Light blue

L: Blue
0: Orange Y: Yellow

Lg: U htgreen

1 TSB Revision

-.

-.--

WIRING

HARNESS

- Horn

Circuit

27 HORN CIRCUIT

LV Y m
Ignition switch

OFF

Multi-purpose fuse

To wiper motor [Refer to P.&W,

88.1

Column

switch Horn tEvcPEPw

37WO98

Remarks (1) Lines indicated by the * symbol are applicable to the P.&liter models. (2) For information concerning the ground points (example: 8). refer to P.812. 14. Wiring color code B: Black Br: Brown LI: Light blue 0: Orange G: Green P: Pink I TSB Revision L: Blue Y: Yellow

Lg: Li ht green W: W%te

WRING HARNESS - Sunroof Circuit

28 SUNROOF CIRCUIT
Ignition --?. Battery B-72 wl+y-J ml Main fusible link q switch

OFF ACC
C-66

I
-

A c!l
%~ultipurpose

2-LW

Sunroof power relay (B&k)

Dedicated fuse

-------(R)

1.25-G 1.25-B
Sunroof motor D-40 rfb

Remarks For details concerning to P.&14.

I the ground point (example: 0). refer Sunroof switch

I
37W687

Wiring color code B: Black Br: Brown LI: Light blue 0: Orange

G: Green P: Pink

g;:$Y

L: Blue Y: Yellow

Lg: Light green W: White

[ TSB Revision

8-114
Multi-purpose Fuse

WIRING HARNESS - Horn Circuit

CENTRALIZED JUNCTION

r control unit, OD-OFF relay, Power

Fuse block

37W716

37w715

1 TSB Revision

WIRING HARNESS - Centralized

Main Fusible Link
Circuit Main circuit Housing color Rated capacity Blue 100

Junction

8-115

Lighting circuit Green 40

Feed back carburetor control circuitiM.P.1. control circuit Pink 30

Sub Fusible

Link
Air conditioner circuit Stop light, door lock and heater circuit Red 0.85 (.0013) 34 150 Ignition circuit Red 0.85 (.0013) 34 150

i Cable color Fusible link size mm2 (in21 Permissible continuous current Fusing current A

Red 0.85 1.0013) 34 150

Dedicated

Fusible

Link
Defogger cirtcuit

I
15 15 20 20

Power window

Cable color Fusible link size mm2 (in.2) Permissible continuous current Fusing current A

Red 0.85 (.0013) 34 150

Dedicated

Fuse
Items I Rated capacity A I

Upper beam indicator circuit Central locking system circuit Sunroof circuit 2.6L Engine Front air conditioner Rear air conditioner circuit circuit (Dual type) 3.OL Engine

1 TSB Revision