Xserve

 Service Source
Xserve
Xserve, Xserve (Slot Load), and Xserve (Cluster Node)
Updated: 7 May 2003
© 2003 Apple Computer, Inc. All rights reserved.

 Service Source
Take Apart
Xserve

General Information
Overview
Xserve is a server designed to mount into a rack; Apple recommends that you remove the
Xserve from the rack before replacing or installing all parts except hard drives. You can
replace hard drives while the server is operating and still in the rack.
There are three versions of the Xserve server. To identify the versions, check the front
panel. The original Xserve includes a tray-load optical drive on the far right side; Xserve
(Slot Load) includes a slot-load optical drive. Xserve (Cluster Node) has no optical drive
and just one hard drive.
Note: For the most part, the procedures in this chapter apply to all versions of the server.
When different procedures are required, the version is specified in the topic heading.
General Information Xserve Take Apart - 1

Mounting in a Rack
For information on mounting Xserve in a rack, see the Xserve User’s Guide.
Tools
Many take-apart procedures do not require tools. You may, however, find a medium-sized
flatblade and Phillips screwdriver useful, as indicated at the beginning of some
procedures. If the server is locked, you will also need the server’s Allen wrench key.
Server Identifier Light/Button

The identifier light on the server’s front panel turns on when internal sensors or a systems
administrator detects a problem with the server. (The light can also be turned on by
pressing the identifier button.) This indicator will help you locate which server in a rack
needs servicing. In addition, you can use the identifier button on the Xserve (Slot Load)
and Xserve (Cluster Node) to initiate several firmware commands to the system. See
“Entering Firmware Boot Commands From the Front Panel” in the Troubleshooting
chapter.
Note: A duplicate identifier light/button is on the server’s back panel.
Before Opening the Server
Serial Number
Be sure to write down the server’s serial number before opening it. If the server’s software
must be set up after service is complete, the serial number will be required for login.
Unlocking the Server

If the server is in the locked position (the yellow security LED on the front panel is on), use
the Allen key that came with the server to unlock it.
Important: When the lock on the server’s front panel is locked, the software ignores the
optical drive, keyboard and mouse, and other peripherals connected to the USB and
FireWire ports on the server.
Shutting Down
You must shut down the server before replacing or installing all parts except the hard
drives. Before shutting down, be sure to alert users that the server will be unavailable for a
period of time.
Warning: After shutting down the server, you must wait a few minutes before servicing it
to allow internal components to cool.
2 - Xserve Take Apart General Information

Electrostatic Discharge (ESD) Precautions
Follow these steps to avoid damage from ESD before working inside the server.
1. Shut down the server.
2. If the cable management arm is not in use, unplug all external cables except the
power cord.
3. Touch the server’s metal case to discharge static electricity.
4. Unplug the power cord.
5. Slide the server open, remove it from the rack, and place it on a flat surface, preferably
covered by an ESD mat.
6. Put on an ESD wrist strap.
7. To avoid static electricity building back up in your body, do not walk around the room
until after you have finished working and closed the server.
Top Cover
The top cover is attached to the rack where the server is mounted. If you are replacing the
top cover, you must remove it both from the server and from the rack. For detailed
information on how the top cover is mounted in the rack, see the User’s Guide.
General Information Xserve Take Apart - 3

Hard Drive
The original Xserve and Xserve (Slot Load) include four hard drive bays at the front of the
server; Xserve (Cluster Node) includes just one drive bay. Drives come as modules
attached to carriers; they are removed from or installed in the server as a unit.
Note: Blank drive carriers, which may fill some of the hard drive bays, follow the same
take-apart procedure as hard drives. If you are replacing a blank carrier with a drive
module, instruct the server’s administrator to keep the blank for possible future use. Blank
carriers must be installed in all empty bays to maintain proper airflow through the server.
Tools
No tools are required for this procedure.
Preliminary Steps
Before you begin, make sure the drives are in the unlocked position. No other preliminary
steps are required. You can replace or install hard drives while the server is running; you
do not need to shut down or open the server first.
Note: There are two LED indicators on the front of each drive.
• The upper LED shows drive status: a green light indicates the drive is good; a yellow
or red light indicates the drive should be replaced.
• The lower LED shows drive activity: when the light is blinking, the system is reading
from or writing to the drive. To avoid losing data, never remove a drive when the lower
LED is blinking.
WARNING: Drives must be in the unlocked position before you attempt to remove a drive.
If the drives are locked, pulling on the drive to remove it could damage the drive handle.
Part Location
4 - Xserve Take Apart Hard Drive

Procedure
1. Make sure the drive being replaced is not in use by any application and is not being
shared by the server. (See the Mac OS X Server documentation for information about
shared drives.)
2. Unmount the drive (by using the command-line tools or by dragging the disk icon to
the Trash).
3. Press the handle on the front of the drive module so that the handle pops out.
4. Wait for the upper LED on the drive to go out. Then grasp the drive handle, and pull
the drive module out of the server.
Hard Drive Xserve Take Apart - 5

Opening the Server
The server slides open from the front of the rack. The server’s top cover remains in place
in the rack; the bottom housing (containing all internal components) should be placed on a
sturdy, flat surface.
Tools
No tools are required for this procedure. You may, however, find a Phillips screwdriver
useful in releasing the thumb screws in step 1 below.
Preliminary Steps
Before you begin this procedure, write down the server’s serial number located on the
back panel. If it is necessary to set up the server’s software after service is complete, the
serial number will be required for login.
6 - Xserve Take Apart Opening the Server

Procedure
1. Release the two thumb screws at the front of the server.
Note: The thumbscrews are captive and do not separate from the bottom housing.
2. Grasp the thumbscrews and slide the bottom housing forward part way to expose the
two chassis levers.
3. While depressing both levers, pull the bottom housing all the way forward and remove
it from the rack. Place the bottom housing on a sturdy, flat surface and ESD mat.
Opening the Server Xserve Take Apart - 7

DIMMs
Xserve has four memory slots. For the original Xserve, DIMMs must be PC2100 double-
data-rate (DDR) SDRAM (also known as DDR-266 DIMMs). For the Xserve (Slot Load)
and Xserve (Cluster Node), DIMMs must be PC2700 DDR SDRAM (also known as DDR-
333 DIMMs). The DIMMs from older Macintosh computers are not compatible with Xserve.
Tools
Preliminary Steps
Before you begin, open the server and place the bottom housing on a sturdy, flat surface.
Part Location
8 - Xserve Take Apart DIMMs

Procedure
1. Push down the ejectors on the DIMM slot.
2. Holding the DIMM by both top corners, lift it straight up out of the server.
Warning: When removing or installing the DIMM, handle it only by the edges. Do not
touch its connectors. Lift the DIMM straight up from the connector to remove it, and insert
it straight down into the connector to install it. Do not rock the DIMM from side to side.
Replacement Note: The DIMM is designed to fit into the slot only one way. Be sure to
align the notch in the DIMM with the small rib inside the slot.
DIMMs Xserve Take Apart - 9

PCI or AGP Card
In the original Xserve and Xserve (Slot Load), there are three slots available for PCI
expansion cards. Two slots are on a riser card located at the back left corner of the logic
board; an additional slot is on a riser card at the back right corner of the logic board. A PCI
card that is 7 inches long can be installed in either riser card; a PCI card that is 12 inches
long can be installed only in the dual-slot riser. In addition, an AGP card can be installed in
the single-slot riser. The Xserve (Cluster Node) includes just two slots for PCI cards on the
dual riser card.
Dual-Slot Riser Card

• Accommodates long cards (12") or short cards (7")
• Standard config comes with PCI video card installed; other cards are CTO options.
• Takes 3.3V, 64-bit/66-MHz or 32-bit/33-MHz cards. If one 33-MHz card is installed, all
cards run at 33-MHz
• Compatible with PCI only
Single-Slot Riser Card

• Accommodates short cards (7") only
• Standard config comes with no card installed; a PCI Gigabit Ethernet card and an AGP
video card are available as CTO options for this slot.
• Takes 3.3V, 32-bit/66-MHz cards
• AGP/PCI riser compatible with PCI cards; AGP/AGP riser compatible with AGP cards
Note: Power consumption for all expansion slots, combined, should not exceed 45 W.
Tools
No tools are required for this procedure. You may, however, find a flatblade screwdriver
useful in releasing the thumb screw in step 1 below.
Preliminary Steps
Warning: When removing or installing a PCI or AGP card, handle it only by the edges. Do
not touch its connectors or any of the components on the card. Lift the card straight out
from the connector to remove it, and insert it straight into the connector to install it. Do not
rock the card from side to side and don’t force the card into the slot. Once the replacement
card is installed, pull on it gently to check that it is properly connected.
10 - Xserve Take Apart PCI or AGP Card

Part Location
Card in Single-Slot Riser
Card in Dual-Slot Riser
Procedure for Card in Dual-Slot Riser

1. Release the thumb screw that secures the card fence to the back of the server.
2. If there are latches on either side of the riser, lift them slightly to release the riser from
the logic board.
3. Pull the riser a short distance to the side to disconnect it, and then tilt the riser and
attached card(s) up so that the card ports clear the enclosure. Remove the riser and
card(s) from the server.
PCI or AGP Card Xserve Take Apart - 11

4. Disconnect the card(s) from the riser.
Procedure for Card in Single-Slot Riser

1. Release the thumb screw that secures the card fence to the back of the server.
12 - Xserve Take Apart PCI or AGP Card

2. Pull the clip on the riser forward to release the riser from the logic board connector.
3. Disconnect the riser from the logic board and remove the riser and card from the
server.
4. Disconnect the card from the riser.
PCI or AGP Card Xserve Take Apart - 13

Optical Drive, Xserve
Tools
The following tools are required for this procedure:
• Flatblade screwdriver
• Phillips screwdriver
If you are removing the drive faceplate, you will also need a jeweler’s (#00) Phillips
screwdriver.
Preliminary Steps
Part Location
14 - Xserve Take Apart Optical Drive, Xserve

Procedure
1. Disconnect the optical drive cable from the optical drive.
2. Press in on the drive’s side bracket to release the drive from the chassis.
3. Lift up the bracket side of the drive and remove the drive from the server.
Optical Drive, Xserve Xserve Take Apart - 15

Note: If you are replacing the optical drive faceplate, do the following:
4. Open the optical drive tray by inserting a straightened paperclip into the manual eject
hole on the front of the drive.
5. Turn the drive over so the bottom of the drive faces up. Using a small (#00) Phillips
screwdriver, remove the two screws that secure the faceplate.
6. Using a small flat-blade screwdriver, release the latch on the far right end of the
faceplate.
7. Remove the faceplate from the drive.

Replacement Note: Before installing the replacement drive, you must transfer the side
bracket and the guide screws from the original drive to the replacement drive.
8. Remove the two screws that secure the side bracket to the original drive.
9. Remove the bracket and transfer it to the replacement drive, using the two screws
from the original drive to secure the bracket.
10. Remove the two guide screws from the side of the original drive and install them on
the replacement drive.
Optical Drive, Xserve Xserve Take Apart - 17

11. Align the corner of the replacement drive with the two guides in the chassis and press
the drive down until you hear it snap into place.
12. Reconnect the optical drive cable to the drive.

Optical Drive,
Xserve (Slot Load)
Tools
The only tool required for this procedure is a jeweler’s Phillips (#0) screwdriver.
Preliminary Steps
Part Location
Optical Drive, Xserve (Slot Load) Xserve Take Apart - 19

Procedure
1. Disconnect the optical drive cable.
2. Rotate the optical drive clip clockwise to release it.
3. Placing your thumbs on the tab on either side of the drive, carefully slide the drive
back from the front bezel.
Important: When removing or replacing the optical drive, be careful not to put
pressure on the top of the drive or the top of the front bezel that covers the optical
drive slot.
4. LIft the drive out of the server.
20 - Xserve Take Apart Optical Drive, Xserve (Slot Load)

Replacement Note: Before installing the replacement drive, you must transfer the side
brackets and the screws from the original drive to the replacement drive.
5. Remove the mounting screw for the left bracket and transfer the bracket to the new
drive, using the same screw to secure it.
6. Remove the three mounting screws for the right bracket and transfer the bracket to the
new drive, again using the same screws to secure it.
Optical Drive, Xserve (Slot Load) Xserve Take Apart - 21

Optical Drive Cable
Tools
Preliminary Steps
Part Location
22 - Xserve Take Apart Optical Drive Cable

Procedure
1. Disconnect the optical drive cable from the optical drive.
2. Disconnect the cable from the drive interconnect board and remove the cable from the
server.
Optical Drive Cable Xserve Take Apart - 23

Heatsink, Xserve
Note: This procedure applies to the original Xserve only. The heatsink for Xserve (Slot
Load) and Xserve (Cluster Node) is part of the processor and should not be removed
separately.
Tools
The only tool required for removing the heatsink is a Phillips screwdriver.
Preliminary Steps
Part Location
24 - Xserve Take Apart Heatsink, Xserve

Procedure
1. Release the latch on the heatsink duct from its slot, slide the cover away from the
blower, and lift the end of the duct as shown. Remove the duct from the server.
2. Release the three captive screws that secure the heatsink.
3. Lift the heatsink straight up and remove it from the server.
Heatsink, Xserve Xserve Take Apart - 25

WARNING: Whenever you remove the heatsink, before reinstalling it, you must replace
the thermal grease on the MPU. To replace the grease, do the following:
• Using the alcohol pad included with the replacement part or kit, clean off any used
thermal grease from the MPU and the bottom of the heatsink.
• Using the thermal grease included with the replacement part or kit, apply one dot of
fresh grease to the middle of the MPU (or both MPUs if the server is a dual processor).
• Spread the grease evenly across the MPU(s) to a thickness of approximately 1 mm.
• Carefully align the posts on the heatsink with the holes in the processor card, and
lower the heatsink straight down onto the processor.
• To ensure the grease spreads evenly over the processor, lightly tighten the screws in
the order indicated below.
• Again tighten the screws in the order indicated to affix the heatsink securely to the
processor.
• Replace the heatsink duct on the heatsink.
26 - Xserve Take Apart Heatsink, Xserve

Processor, Xserve
Tools
Preliminary Steps
Before you begin, do the following:
• Open the server and place the bottom housing on a sturdy, flat surface.
• Remove the heatsink.
Part Location
Processor, Xserve Xserve Take Apart - 27

Procedure
1. Lift the processor straight up to disconnect it from the logic board.
2. Remove the processor from the server.
28 - Xserve Take Apart Processor, Xserve

Processor, Xserve (Slot Load)
and Xserve (Cluster Node)
Tools
The following tools are required for this procedure
• installation guides (included with the processor service part)
Preliminary Steps
Part Location
Processor, Xserve (Slot Load) and Xserve (Cluster Node) Xserve Take Apart - 29
Procedure
1. Using a Phillips screwdriver, remove the three screws that mount the heatsink and
processor to the logic board.
2. Carefully lift the heatsink and processor straight up and out of the server.
Note: The heatsink is part of the processor; do not attempt to remove the heatsink from
the processor.
30 - Xserve Take Apart Processor, Xserve (Slot Load) and Xserve (Cluster Node)
Replacement Procedure
1. Insert the threaded end of one of the processor installation guides into the logic board
standoff on the right side of the processor connector. Twist the guide until it screws
into place.
2. Insert the second processor installation guide into the standoff on the left side of the
processor connector and twist until the guide screws into place.
3. Carefully align the screw holes on the replacement heatsink and processor with the
two guides, and lower the unit straight down over the guides until it touches the logic
board.
4. To secure the processor to the logic board, press down gently on the top of the
heatsink cover in the area directly over the processor's connector.
32 - Xserve Take Apart Processor, Xserve (Slot Load) and Xserve (Cluster Node)
5. Remove the two installation guides.
6. Replace the three mounting screws and secure the processor and heatsink to the
logic board.
Blowers
Tools
Preliminary Steps
Part Location
34 - Xserve Take Apart Blowers

Procedure
1. Disconnect the blower cable from the drive interconnect board.
2. Lift the blower straight up off its mounting pegs and remove it from the server.
Blowers Xserve Take Apart - 35

ATA Controller Board
Tools
Preliminary Steps
• If the unit is an original Xserve, remove the heatsink duct from the heatsink.
Note: There is no heatsink duct on the Xserve (Slot Load) and Xserve (Cluster Node).
Part Location
36 - Xserve Take Apart ATA Controller Board

Procedure
1. Disconnect the blower cable nearest the ATA controller board.
2. Press in on both ends of the clip securing the right side of the ATA controller board and
remove the clip from the server. Repeat for the clip on the left side of the board.
3. Lift the ATA controller board straight up to disconnect it from the drive interconnect and
logic boards and remove the board from the server.
Note: When replacing the ATA controller board, align it over the two pairs of connectors on
the drive interconnect and logic boards, making sure the “MLB” arrow printed on it points
toward the logic board, and press down.
ATA Controller Board Xserve Take Apart - 37

Note: When replacing the ATA controller board clips, orient them so that the long end of
each clip points away from the middle of the server. Place the inside edge of the clip into
the small notch and then snap down the outer edge of the clip.
38 - Xserve Take Apart ATA Controller Board

Locking Mechanism Rod,
Xserve
Tools
Preliminary Steps
Part Location
Locking Mechanism Rod, Xserve Xserve Take Apart - 39

Procedure
1. Pull back the latch to release the ribbed end of the locking mechanism rod.
2. Release the two clips on the sides of the front panel board, and pull the board back
slightly from the front of the server.
3. Tilt up the ribbed end of the locking mechanism rod and remove the rod from the
server.
40 - Xserve Take Apart Locking Mechanism Rod, Xserve

Note: When replacing the locking mechanism rod, make sure the first rib in the nylon roller
engages with the first slot in the plate below it.
Locking Mechanism Rod, Xserve Xserve Take Apart - 41

Locking Mechanism Rod,
Xserve (Slot Load) and
Xserve (Cluster Node)
Tools
Preliminary Steps
Part Location
42 - Xserve Take Apart Locking Mechanism Rod, Xserve (Slot Load) and Xserve (Cluster Node)
Procedure
1. Pull back the latch to release the gear end of the locking mechanism rod.
2. Tilt up the gear end of the rod and remove the rod from the server.
3. If you are replacing the plastic gear on the end of the rod, slide the gear off the rod.
1. To install the gear, slide it onto the notched end of the locking rod, aligning the narrow
end of the gear with the end of the rod.
Note: Make sure the rib inside the gear engages with the notch in the rod.
Locking Mechanism Rod, Xserve (Slot Load) and Xserve (Cluster Node) Xserve Take Apart - 43
2. To install the locking rod, insert the end of the rod with the key hole into the port on the
front bezel.
Note: Make sure the small circle on the front of the rod aligns with the “unlocked”
symbol on the front bezel.
3. Pull back the latch that secures the rod, and gently press the rod down until it clicks
into place.
44 - Xserve Take Apart Locking Mechanism Rod, Xserve (Slot Load) and Xserve (Cluster Node)
Front Bezel, Xserve (Slot Load)
Tools
The only tool required for this procedure is a Phillips screwdriver.
Preliminary Steps
Note: Although the illustrations for this procedure are based on Xserve (Slot Load), the
procedure is the same for Xserve (Cluster Node).
Part Location
Front Bezel, Xserve (Slot Load) and Xserve (Cluster Node) Xserve Take Apart - 45
Procedure
1. Using a Phillips screwdriver, remove the screws that attach the two front bezel
brackets to the server, and remove the brackets.
2. Remove the screw that attaches the top of the bezel to the server.
3. Gently pull the front bezel forward and remove it from the server.
Important: When removing or replacing the bezel, be careful not to put pressure on
the top of the bezel over the optical drive slot.
46 - Xserve Take Apart Front Bezel, Xserve (Slot Load) and Xserve (Cluster Node)
1. Transfer the system identifier and power buttons from the original front bezel to the
replacement bezel.
2. Remove the bottom row of light pipes from the light pipe assembly and insert them
into the bottom row of light pipe holes in the replacement bezel.
3. Replace the front bezel on the server, matching ports/projections with openings.
4. Replace the screw that secures the top of the bezel to the server.
5. Replace the two bezel brackets and their mounting screws.
Front Bezel, Xserve (Slot Load) and Xserve (Cluster Node) Xserve Take Apart - 47
Front Buttons,
Note: This procedure explains how to remove the power and system ID buttons from the
front bezel.
Tools
Preliminary Steps
• Remove the front bezel.
Part Location
48 - Xserve Take Apart Front Buttons, Xserve (Slot Load) and Xserve (Cluster Node)
Procedure
1. Holding the power button by the plastic tab, lift straight up and remove the button from
the front bezel.
2. Repeat for the system ID button.
Note: Take care in handling the buttons. The face of each button is loosely attached
to the button LEDs and can easily separate.
Replacement Note: Position the replacement buttons in the front bezel as illustrated.
Front Buttons, Xserve (Slot Load) and Xserve (Cluster Node) Xserve Take Apart - 49
Front Panel Board, Xserve
Tools
Preliminary Steps
• Remove the locking mechanism.
Part Location
50 - Xserve Take Apart Front Panel Board, Xserve

Procedure
1. Disconnect the FireWire and front panel board cables from the board.
2. Lift the board out of the server.
Front Panel Board, Xserve Xserve Take Apart - 51

Front Panel Board,
Tools
Preliminary Steps
• Remove the locking mechanism.
Part Location
52 - Xserve Take Apart Front Panel Board, Xserve (Slot Load) and Xserve (Cluster Node)
Procedure
1. Disconnect the FireWire and front panel board cables from the board.
2. Remove the two screws that mount the front panel board to the chassis.
3. Slide the board back and remove it from the server.
Important: When replacing the front panel board, make sure the board slides under the
black plastic cover of the light pipe.
Front Panel Board, Xserve (Slot Load) and Xserve (Cluster Node) Xserve Take Apart - 53
Light Pipe, Xserve
Tools
Preliminary Steps
Part Location
54 - Xserve Take Apart Light Pipe, Xserve

Procedure
1. Release the two clips on the sides of the front panel board, and pull the board back
approximately 1.5 inches from the front of the server.
2. Remove the light pipe from the server.
Replacement Note: When repositioning the light pipe against the inside front of the bezel,
make sure the projections on the light pipe fit into the holes in the bezel. Then slide the
panel board forward until it fits against the light pipe. Note: You may need to lift the light
pipe slightly while sliding the front panel board, so that it doesn’t catch the edge of the light
pipe.
Light Pipe, Xserve Xserve Take Apart - 55

Light Pipe, Xserve (Slot Load)
Tools
The following tools are required for this procedure:
• flat-blade screwdriver
Preliminary Steps
Part Location
56 - Xserve Take Apart Light Pipe, Xserve (Slot Load) and Xserve (Cluster Node)
Procedure
1. Using a flat-blade screwdriver, ease first one side and then the other side of the light
pipe assembly from its opening in the front of the enclosure.
2. Remove the light pipe assembly from the server.
1. Remove the bottom row of light pipes from the light pipe assembly and insert them
into the bottom row of light pipe holes in the front bezel.
Light Pipe, Xserve (Slot Load) and Xserve (Cluster Node) Xserve Take Apart - 57
2. Insert the rest of the light pipe assembly into its opening in the front of the enclosure.
3. Replace the front bezel on the server, matching ports/projections with openings.
4. Replace the screw that secures the top of the bezel to the server.
5. Replace the two bezel brackets and their mounting screws.
58 - Xserve Take Apart Light Pipe, Xserve (Slot Load) and Xserve (Cluster Node)
Front Panel Board Cable
Tools
Preliminary Steps
Part Location
Front Panel Board Cable Xserve Take Apart - 59

Procedure
1. Disconnect the front panel board cable from the front panel board.
2. Disconnect the front panel board cable from the drive interconnect board and remove
the cable from the server.
60 - Xserve Take Apart Front Panel Board Cable

FireWire Cable
Tools
Preliminary Steps
Part Location
FireWire Cable Xserve Take Apart - 61

Procedure
1. Disconnect the FireWire cable from the front panel board.
2. Disconnect the FireWire cable from the drive interconnect board and remove the cable
from the server.
62 - Xserve Take Apart FireWire Cable

Drive Interconnect Board
Tools
useful in releasing the thumb screws in step 2 below.
Preliminary Steps
Before you begin, open the server and remove the following:
• hard drives (blank drive carriers can remain in place)
• blowers
• ATA controller board
Part Location
Drive Interconnect Board Xserve Take Apart - 63

Procedure
1. Disconnect the following cables from the drive interconnect board
• optical drive cable
• power supply cable
• locking switch cable
• front panel board cable
• FireWire cable
2. Release the three thumb screws that secure the drive interconnect board to the
chassis.
3. Lift the board slightly to clear the two mounting pegs near both ends of the board.
4. Pull the board back, tilt it up so that the connectors clear the chassis, and remove the
board from the server.
64 - Xserve Take Apart Drive Interconnect Board

Replacement Note: When installing the drive interconnect board, make sure the board
engages with the two mounting pegs (#1 in the illustration below) and the three brackets
(#2) on the chassis. Then press the board firmly toward the front of the server, and tighten
the three thumbscrews (#3) that secure the board to the chassis.
Drive Interconnect Board Xserve Take Apart - 65

Power Supply
Tools
Preliminary Steps
• If the unit is an original Xserve, remove the heatsink duct from the heatsink.
Note: There is no heatsink duct on the Xserve (Slot Load) and Xserve (Cluster Node).
Part Location
66 - Xserve Take Apart Power Supply

Procedure
1. Release the locking latch on the power supply cable connector and disconnect the
cable from the drive interconnect board.
2. Release the thumbscrew that secures the power supply to the chassis.
Note: The thumbscrew is captive; you cannot remove it.
3. Grasp the metal flange of the power supply’s connector (on the left side) and lift up to
disconnect the power supply from the logic board.
Note: You may need to loosen the left side of the power supply and then lift at
another point near the front to disengage it. Do not lift the small lip that contains the
thumbscrew.
4. Holding the power supply in both hands, remove it from the server.
Power Supply Xserve Take Apart - 67

Battery
Tools
No tools are required for this procedure. You may, however, find a flatblade screwdriver
useful in prying up the battery in step 1 below.
Preliminary Steps
Part Location
68 - Xserve Take Apart Battery

Procedure
1. Pry up the battery from its holder.
Note: You may first need to spread the two tabs on the holder slightly apart to
release the battery.
2. Remove the battery from the server.
Note: When replacing the battery, make sure the positive (+) end of the battery aligns with
the + symbol on the battery holder.
Battery Xserve Take Apart - 69

Logic Board
Tools
useful in releasing the thumb screw in step 1 below.
Preliminary Steps
Before you begin, open the server and remove the following.
• DIMMs
• PCI cards
• processor
• ATA controller board
• power supply
Note: The replacement logic board does not include the processor, memory DIMMs, or
expansion cards. You must transfer these modules from the original board to the new one.
Part Location
70 - Xserve Take Apart Logic Board

Procedure
1. Release the thumb screw that secures the logic board to the chassis.
2. Move the logic board forward and up slightly to release it from the four mounting pegs.
3. Tilt up the end of the logic board nearest the blowers so that the board ports clear the
chassis.
4. Remove the board from the server.
Replacement Note: Before installing the replacement logic board, check the heatsink
thermal pad on the underside of the board. If the pad is covered with a protective film,
remove it. (The protective film is a very thin layer on top of the thermal pad. Be careful to
remove only the film, not the pad.)
Logic Board Xserve Take Apart - 71

Important: When replacing the logic board, make sure the board’s connectors fit through
the appropriate openings in the server’s back panel. Take special care to fit the clear
plastic system identifier button through its opening. (The system identifier button is located
low on the back panel, to the left of center.)
After installing a replacement logic board, be sure to transfer any PCI cards, risers, and
DIMMs to the new board. You must also remove the battery insulator tab from the battery
holder on the new board.
Note: Replacing the logic board in the server changes its Ethernet ID number. The new
number is printed on an Ethernet ID label packaged with the replacement logic board.
After installing the new logic board, cover the Ethernet ID number on the server’s serial
number with the new ID label.
72 - Xserve Take Apart Logic Board

 Service Source
Troubleshooting
Xserve

General Information
What’s New
Rack-Mounted Server
Xserve is designed to be mounted in a rack. Once the server is installed in the rack, you
can slide it open from the front to exchange or add parts.
For more information, see “Opening the Server” in the Take Apart chapter.
Server Identifier Light/Button

The identifier light on the server’s front panel turns on when internal sensors or a systems
administrator detects a problem with the server. (The light can also be turned on by
pressing the identifier button.) This indicator will help you locate which server in a rack
needs servicing. In addition, you can use the identifier button to initiate several firmware
commands to the system. See “Entering Firmware Boot Commands From the Front Panel”
in this chapter.
Note: A duplicate identifier light/button is on the server’s back panel.
Hot-Pluggable ATA Drives

The original Xserve and Xserve (Slot-Load) include four hard drive bays at the front of the
server; the original Xserve supports hot-pluggable Apple ATA/100 drive modules and the
Xserve (Slot Load) supports ATA/133 drive modules. The Xserve (Cluster Node) includes
just one Apple ATA/133 drive module.
In the original Xserve and Xserve (Slot Load) drive bays are numbered 1–4, beginning
with the far left bay. The bay in which a drive is installed determines its master/slave
position, thereby eliminating the need for jumpers or special drive configuration. The drive
installed in bay 1 is the master drive and should have the operating system installed on it.
In all three models, you can replace or install hard drives while the server is running; you
do not need to shut down or open the server first. A status light on the front of each drive
indicates when it is safe to remove the drive without losing data. For more information, see
“Hard Drive” in the Take Apart chapter.
General Information Xserve Troubleshooting - 1

Diagnostics
Four types of diagnostics are available for Xserve:
• status lights
• remote monitoring
• Apple Hardware Test
• Apple Service Diagnostic
For more information, see “Diagnostic Tools” below.
DDR Memory
The server’s logic board includes four memory slots, which accept double data rate (DDR)
SDRAM DIMMs. Memory can be expanded to a maximum of 2 gigabytes.
DIMMs used in the original Xserve must fit these specifications:

• PC2100 DDR SDRAM, also known as DDR-266
• 2.5 volt
• 64-bit wide, 184-pin module
• unbuffered (do not use registered or buffered DRAM)
• maximum height of 1.3 inches
DIMMs used in Xserve (Slot Load) and Xserve (Cluster Node) must fit these
specifications:
• PC2700 DDR SDRAM, also known as DDR-333
• 2.5 volt
• 64-bit wide, 184-pin module
• 16 memory devices maximum
• unbuffered (do not use registered or buffered DRAM)
• maximum height of 1.25 inches
Important: DIMMs from older Macintosh computers are not compatible with Xserve. Do
not use older DIMMs even if they fit into the DIMM slots.
Ports
The standard configuration of the original Xserve includes the following ports on the back
panel: one or two gigabit Ethernet ports, two FireWire 400 ports, two USB ports, a serial
port that supports RS-232 or RS-422 connection, and a VGA monitor port. There is also
one FireWire 400 port on the front of the server.
The standard configuration of Xserve (Slot Load) includes the following ports on the back
panel: one or two gigabit Ethernet ports, two FireWire 800 ports, two USB ports, a serial
port that supports RS-232 connection, and a VGA monitor port. There is also one FireWire
400 port on the front of the server.
The standard configuration of Xserve (Cluster Node) includes the following ports on the
back panel: one gigabit Ethernet port, two FireWire 800 ports, two USB ports, and a serial
2 - Xserve Troubleshooting General Information

port that supports RS-232 connection. There is also one FireWire 400 port on the front of
the server.
System administrators or service providers can connect a laptop computer or terminal to

the serial port and then use command-line tools to change settings on the server. The
connection requires a serial cable with these specifications:
• DB9 connector
• 8-bit
• no parity
• 1 stop bit
• 9600 kbps
Note: For a diagram of the ports location, see “External Views” in the Views chapter.
PCI and AGP Cards

In the original Xserve and Xserve (Slot Load), there are three slots available for PCI
expansion cards. Two slots are on a riser card located at the back left corner of the logic
board; an additional slot is on a riser card at the back right corner of the logic board. A PCI
card that is 7 inches long can be installed in either riser card; a PCI card that is 12 inches
long can be installed only in the dual-slot riser. In addition, an AGP card can be installed in
the single-slot riser. The Xserve (Cluster Node) includes just two slots for PCI cards on the
dual riser card.
The standard configuration for the original Xserve and Xserve (Slot Load) comes with a
VGA video card installed in the bottom slot of the dual-slot riser and a gigabit Ethernet
card installed in the single-slot AGP/PCI riser. In addition, a high-end AGP video card is
available as a CTO option for these models; it replaces the gigabit Ethernet PCI card in the
single-slot riser position and requires installing an AGP/AGP riser card that is bundled with
the video card. The Apple Fibre Channel PCI card, which allows connection to Xserve
RAID, is also available as a CTO option for Xserve and Xserve (Slot Load); it must be
installed in the top slot of the dual-slot riser.
Note: Combined power consumption for all expansion slots within one unit should not
exceed 45 W.

Block Diagram
Processor Module
L3 Cache PowerPC G4
Microprocessor
Main Logic Board
DIMM Slots Ethernet

Ethernet Port
PHY
U2
memory Firewire Firewire Port 1
controller PHY
U2PCI
and Firewire Port 2
Memory
bus bridge
Controller Firewire Firewire Port 3
and PCI PHY
Network Card Slot Bus Bridge
Boot PCI Slots

ROM
PCI
Bridge
PCI
Bridge
ATA ATA
Interface Interface
USB Port 1
USB Port 2
KeyLargo
Apple Drive Module I/O Device Serial Port
Connectors and Disk
Controller
Internal Optical
EIDE PMU99
Drive Connector
Bus Power
Controller

Resetting the PMU on the Logic Board
The PMU (Power Management Unit) is a microcontroller chip that controls all power
functions for the server. The PMU is a computer within a computer. Its function is to:
• tell the server to turn on, turn off, sleep, wake, idle, etc.
• manage system resets from various commands.
• maintain parameter RAM (PRAM).
• manage the real-time clock.
Important: Be very careful when handling the logic board. The PMU is very sensitive and
touching the circuitry on the logic board can cause the PMU to crash. If the PMU crashes
and is not reset, the battery life goes from about five years to about two days.
Note: For the location of the PMU reset button, see “Logic Board Diagram” in the Views
chapter.
Many system problems can be resolved by resetting the PMU chip. When you have a
server that fails to power up, follow this procedure before replacing any modules:
1. Disconnect the power cord and check the battery in the battery holder. The battery
should read 3.3 to 3.7 volts. If the battery is bad, replace it, wait ten seconds, and then
proceed to step 2. If the battery is good, go directly to step 2.
2. Press the PMU reset button once and then proceed to step 3. Do not press the PMU
reset button a second time because it could crash the PMU chip.
3. Wait ten seconds before connecting the power cord and powering on the server. If the
server powers on, go to step 4. If the server does not power on, there is something
else wrong with it; refer to the “System” section of “Symptom Charts” in this chapter.
4. Run Apple Hardware Test to verify the system.
Note: The above procedure resets the server’s PRAM. After resetting the PMU, be sure to
reset the time, date, and other system parameter settings.

Power Supply Verification
To power on, the server’s logic board requires a “trickle” power of +5V. If the system fails to
power on, first reset the PMU. Then follow the procedure outlined below to determine
whether the problem is related to the power supply.
Note: To verify the power supply, you need a volt meter. When connecting the volt meter
leads to specific pins, make sure the power supply remains securely plugged into its
connector on the logic board.
The following figure shows the pins and voltage on the server’s power supply connector,
as viewed from above when it is connected to the logic board.
Pin 1 +12VDC +12VDC Pin 13
Pin 2 GND GND Pin 14
Pin 3 +12VDC GND Pin 15
Pin 7 +3.3VDC GND Pin 19
Pin 10 -12VDC GND Pin 22
Pin 11 Power On GND Pin 23
Pin 12 +5VSB GND Pin 24
1. Plug a known-good power cord into the server. Do not turn on the server.
2. Connect the black lead of the volt meter to pin 14 of the power supply connector;
connect the red lead of the volt meter to pin 1. The volt meter should measure
approximately +12V.
If you do not get a reading of +12V, recheck the volt meter connections and measure
the voltage again. If voltage is still not present, replace the power supply.
If you do measure +12V on pin 1, the power supply is likely OK. Go to the next step
for further verification.
3. Start up the server by pressing the power button on the front panel.
If the server starts up normally, the power supply is OK. If the server does not start
up normally, go to the next step.

4. Check to see if the power supply fan is spinning.
If it is not, replace the power supply. If it is spinning, go to the next step.
connect the red lead to pin 9. The volt meter should measure approximately +3.3V.
If you do not get a reading of +3.3V, recheck the volt meter connections and measure
If you do measure +3.3V on pin 9, the power supply is likely OK. Go to the next step
for further verification.
connect the red lead to pin 4. The volt meter should measure approximately +5V.
If you do measure +5V on pin 4, the power supply is likely OK. Go to the next step for
further verification.
connect the red lead to pin 3. The volt meter should measure approximately +12V.
If you do measure +12V on pin 3, the power supply is OK and the testing is complete.
You have verified that the power supply is not the cause of the “no apparent power”
symptom.
RAM and Processor Verification: Power-On Self Test

A power-on self test in the server’s ROM automatically runs whenever the server is started
up after being fully shut down (the test does not run if the server is only restarted). If the
test detects a problem, you will not see a normal sequence of system activity lights on the
front panel during startup. Instead, the lights will flash in the following ways:
• 2 Flashes: No RAM is installed or detected.
• 3 Flashes: Incompatible RAM types are installed.
• 4 Flashes: No RAM banks passed memory testing.
• 5 Flashes: No good boot images are detected in the boot ROM (and/or there is a bad
sys config block).
• 6 Flashes: The processor is not usable.

Xserve (Slot Load and Cluster Node): Entering Firmware Boot
Commands From the Front Panel
You can use the system identifier button on the Xserve (Slot Load) and Xserve (Cluster
Node) server’s front panel to initiate a limited number of firmware commands to the
system without connecting a keyboard or monitor to the server. The commands are listed
below; you enter each command with a combination of the system identifier button and a
specific light on the front panel.
Follow these steps to initiate a command from the front panel.
1. With the power off, hold in the system identifier button while you press the power
button.
2. Continue holding in the system identifier button until the top row of blue lights blinks
sequentially.
3. Release the system identifier button. The rightmost light in the bottom row turns on.
Press the button to light the next light in the bottom row, moving from right to left.
Press the button again to change lights.
The lights in the bottom row indicate (from right to left):

• Light 1 (far right): Start up from the system disc (also ejects any disc in the optical
drive)
• Light 2: Start up from a network server (NetBoot)
• Light 3: Start up from the internal drive (leftmost drive if more than one)
• Light 4: Bypass the current startup disk and start up from any other available startup
disk
• Light 5: Begin target disk mode (all drives, including the optical drive, will show up)
• Light 6: Restore the system’s default settings (reset NVRAM)
• Light 7: Enter Open Firmware (via the serial port if no monitor and keyboard are
connected)
4. When the light for the action you want is on, hold in the system identifier button for at
least 2 seconds, until all lights in the top row are on.
5. Release the button.
Diagnostic Tools
Xserve includes built-in sensors that detect and report on hard drives, internal temper-
ature, blower status or failure, and power status or failure. You can monitor the server’s
operation via these sensors and four diagnostic tools: indicator lights on the front of the
server, remote monitoring software, Apple Hardware Test, or Apple Service Diagnostic.

Status Lights
The server’s status lights are shown in the figure and table below. While the illustration is
based on the original Xserve, the callouts for the status lights are accurate for all models.
Ethernet Card Link Light

[not available on
Xserve (Cluster Node)]
System Identifier System

Button/Light Activity Lights
Enclosure Lock
Power Button /Light
Built-In Drive Module Status Light

Ethernet Drive Module Activity Light
Link Light
Table 1: Status Lights
Indicator Color Description
Power White On and OK
Security lock Yellow Lock is engaged
System identifier Yellow Indicates a hardware error in the server or

that someone has toggled it on; check the
server monitoring application for more
information
Ethernet Green Link

(lower LED is No light No connection
built-in; upper LED
is network card)
System activity Blue Two rows of eight LEDs; in server with one
processor, rows of lights work in tandem; in
dual-processor server, rows operate
independently for each processor
Drive module Green Powered and running

(upper LED) Yellow Warning condition; replace drive
Red Problem or failure; replace drive
Drive module No light Drive can be removed

(lower LED) Blinking blue Disk activity; do not remove drive

Remote Monitoring
Server Monitor is an application installed with Xserve system software that helps you
monitor the following information about the server:
• installed operating system
• drive status and activity
• power supply operation
• enclosure and processor temperature
• blower operation
• security
• network operation
You can also use Server Monitor to get logs of activity and Apple System Profiler reports
on remote servers.
Apple Hardware Test

Apple Hardware Test is a diagnostic tool for detecting problems with Apple internal
hardware components such as logic board, memory, video RAM, and drives. The test
does not check externally connected hardware components such as USB or FireWire
devices; it also does not check non-Apple devices such as third-party PCI cards.
If Apple Hardware Test detects a problem with a computer, it displays an error code, which
is defined in the product's Error Code List. Consult the list for appropriate repair
procedures associated with the code.

All Error Code Lists are included in the Service Diagnostics Matrix, Knowledge Base
article 112125. You can also access this matrix by clicking the Service Diagnostics rollover
link under any of the product areas on the Service Source home page.
Apple Service Diagnostic

Apple Service Diagnostic replaces MacTest Pro for Xserve. It tests memory, logic board
and components, hard drives, Ethernet cards, and video cards, and complements both
Apple Hardware Test and Server Monitor. In addition, it offers the following advantages:
• many choices for selecting tests
• a looping function where tests can be run once, a specified number of times, or a
specified length of time. The looping function is valuable for detecting intermittent
problems that take a long time to generate a failure.
• detailed information about errors
Apple Service Diagnostic can be dowloaded from the Disc Images rollover link on the
Service Source home page.

Symptom Charts
How to Use the Symptom Charts

The Symptom Charts included in this chapter will help you diagnose specific symptoms
related to the product. Because cures are listed on the charts in the order of most likely
solution, try the cures in the order presented. Verify whether or not the product continues
to exhibit the symptom. If the symptom persists, try the next cure.
Note: If a cure instructs you to replace a module, reinstall the original module before you
proceed to the next cure.
Startup
System is completely dead (no blower movement and power LED is not lit)
1. Verify that the system ID button on the back of the logic board aligns with the
opening in the chassis back panel. If it does not, realign the logic board.
2. Verify the power outlet is good.
3. Reseat the ATA controller board.
4. Replace the power cord.
5. Disconnect external devices, including the monitor, and start up the server.
6. Remove internal PCI and AGP cards and start up the server.
7. Verify that the power supply is properly connected to the logic board and drive
interconnect board.
8. Verify the front panel board cable is properly connected at both ends.
9. Reseat the front panel board.
10. Verify all cable connections to the drive interconnect board.
11. Replace the power supply.
12. Replace the ATA controller board.
13. Replace the front panel board cable.
14. Replace the front panel board.
15. Replace the drive interconnect board.
12 - Xserve Troubleshooting Startup Symptom Charts

16. Replace the logic board. Note: When installing the new logic board, make sure the
ports and ID button on the back of the board align with the openings in the chassis.
Memory error message appears on the screen

1. Reseat the DIMMs.
2. Verify that the correct SDRAM DIMMs are installed.
3. Run Apple Hardware Test. If the test finds bad memory, replace the DIMMs one at a
time and test until all bad DIMMs are replaced with known-good modules.
Flashing question mark appears on the screen

1. Reseat the drive module in the first drive bay.
2. Start up from the system restore CD and check to see if the hard drive shows up on
the desktop. If it does, go to step 3. If it does not, go to step 5.
3. Run Disk Utility. Update the driver and restart the server.
4. Reinstall system software using the system restore CD that came with the server.
5. Replace the drive module in the first drive bay.
Server begins to power up, the blowers and hard drive are spinning, the
power LED is lit, but there are no activity lights or video
2. Reset the logic board. Refer to “Resetting the PMU on the Logic Board” in this
chapter.
3. Reseat the processor module.

4. Verify all PCI and AGP cards are seated properly.
5. Replace the processor module.
Server begins to power up, but won’t boot, and top row of activity LEDs
continue to light in sequence left to right and then right to left
chapter.
3. Xserve (Slot Load and Cluster Node): Remove the front bezel and make sure the front
system IDbutton is not stuck. Reseat the button if necessary.
Startup Symptom Charts Xserve Troubleshooting - 13

4. Reseat the front panel board and cable connectors.
5. Replace the front panel board.
System shuts down intermittently

2. Make sure the power cord is plugged in firmly.
3. Check that the power source is turned on and the correct voltage is present.
4. Make sure the air vents are clear.
5. Replace the power cord.
6. Check that the blower cables are connected and the blowers are operational.
7. Check that the heatsink is properly attached to the processor.
chapter.
System shuts down almost immediately after startup

chapter.

14 - Xserve Troubleshooting Startup Symptom Charts

Error Lights
Note: Error lights flash before system software loads.
Server activity lights flash two times at startup

Two flashes mean that no RAM is installed or detected.
1. If no DIMM is present, install a known-good DIMM in the top slot and try again.
2. Reseat the DIMMs.
Server activity lights flash three times at startup

Three flashes mean that incompatible RAM types may be installed. Verify that the correct
SDRAM DIMMs are installed.
Server activity lights flash four times at startup

Four flashes mean that no RAM banks passed memory testing.
Server activity lights flash five or six times at startup

Five or six flashes mean that the ROM is probably bad and cannot be fixed.
Error Lights Symptom Charts Xserve Troubleshooting - 15

Video
Screen is black, but activity lights flash at startup, drive operates, blowers are
running, and power LED is lit
2. Reseat the ATA controller board.
3. Check video card connections and connector pins.
4. Test with a known-good monitor. Replace the monitor, if necessary.
5. Remove all third-party devices.
6. Reseat the video card.
7. Clear parameter RAM. Hold down Command-Option-P-R during startup.
chapter.
9. Replace the video card.
Screen is black, power LED is lit, blowers spin, activity lights do not flash, and
drives do not operate
chapter.

Video is distorted
1. Make sure that the video card driver and firmware are updated to the most recent
versions.
2. Refer to the adjustments section of the service manual or owner’s manual for the
monitor. Adjust monitor as necessary.
3. Third-party monitors: Try a known-good monitor.
4. Reseat the video card.
5. Replace the video card.
16 - Xserve Troubleshooting Video Symptom Charts

Hard Drive
Flashing question mark appears on the screen

1. Reseat the drive module in the first drive bay.
2. Start up from the system restore CD and check to see if the hard drive shows up on
the desktop. If it does, go to step 3. If it does not, go to step 5.
3. Run Disk Utility. Update the driver and restart the server.
4. Reinstall system software using the system restore CD that came with the server.
5. Replace the drive module in the first drive bay.
Hard Drive Symptom Charts Xserve Troubleshooting - 17

Internal Optical Drive
Optical drive icon does not appear on the desktop

1. If the server is locked, unlock it.
2. Check to see if the optical drive is listed in Apple System Profiler. If it is, go to step 3. If
it is not, go to step 9.
3. Verify the correct type of disc is being used. Try using a known-good disc.
4. Try cleaning the disc. (It may not mount if it is dirty or scratched.)
5. If there is a disc stuck in the drive, eject it by restarting the server while holding down
the mouse button.
6. Turn off all third-party extensions.
7. Verify the firmware is the most recent version for that drive. Check Software
Downloads for any current update.
8. Reinstall system software.
9. Reseat the optical drive cable at both connectors.
10. Replace the optical drive cable.
11. Replace the optical drive.
12. Replace the logic board only if other devices on the bus do not work. Note: When
installing the new logic board, make sure the ports and ID button on the back of the
board align with the openings in the chassis.
Optical drive does not accept CD or DVD disc

2. Verify the disc is not warped.

3. Verify the disc is not the wrong size. Refer to article 58641 “Macintosh: Using
Nonstandard Discs in CD-ROM or DVD-ROM Drives.”
Original Xserve: Drive tray won’t open

2. Try using a known-good disc.
18 - Xserve Troubleshooting Hard Drive Symptom Charts

Xserve (Slot Load): Disc will not eject
2. Verify the disc is not in use.
3. Drag the disc icon to the trash or select it and press Command-E.
4. Restart the server while holding down the mouse button.
5. Verify that the bezel over the slot is not bent. If it is, gently bend it back into position.
USB Devices
At startup, cursor does not move with the Apple mouse
2. Verify that mouse and keyboard connections are secure.
3. If the mouse is connected to the keyboard, connect the mouse to one of the USB ports
on the back panel instead. If the mouse works, replace the keyboard.
4. Replace the mouse.
5. If the mouse is connected to one of the USB ports on the back panel, switch to the
other USB port. If the mouse operates correctly, replace the logic board. (You can also
use Apple System Profiler to verify USB ports.) Note: When installing the new logic
board, make sure the ports and ID button on the back of the board align with the
openings in the chassis.
No response to any key on keyboard

2. Verify that keyboard and mouse connections are secure.
3. Remove all USB devices, except the keyboard and mouse. If the keyboard operates
correctly, troubleshoot the other USB devices.
4. Switch the keyboard to a different USB port. If the keyboard operates correctly,
replace the logic board. (You can also use Apple System Profiler to verify USB ports.)
5. Relaunch Finder.
6. Start up from the system installation CD or system restore CD that came with the
server. If the keyboard operates, reinstall system software.
7. Replace the keyboard.
USB Devices Symptom Charts Xserve Troubleshooting - 19

FireWire Devices
FireWire device connected to port on back panel: No external FireWire device
icon appears on the desktop
2. Verify that the FireWire device is turned on and the FireWire cable is securely
connected to the device and the server.
3. If the device requires external power, make sure it is plugged in.
4. Check that the FireWire device is listed in Apple System Profiler. If it is, go to step 5. If
5. Check the FireWire device documentation to see if additional drivers are required. If
so, make sure the drivers are installed.
6. Check for broken pins, dust, dirt, or wear on both FireWire cable connectors, the
device FireWire port, and the server FireWire port.
7. Reconnect the FireWire device to another FireWire port on the server. If the server
has a bad FireWire port, replace the logic board.
8. Replace the FireWire cable.
9. Replace the FireWire device.
FireWire device connected to port on front panel: No external FireWire

device icon appears on the desktop
2. Verify that the FireWire device is turned on and the FireWire cable is securely
connected to the device and the server.
3. If the device requires external power, make sure it is plugged in.
4. Check that the FireWire device is listed in Apple System Profiler. If it is, go to step 5. If
5. Check the FireWire device documentation to see if additional drivers are required. If
so, make sure the drivers are installed.
6. Check for broken pins, dust, dirt, or wear on both FireWire cable connectors, the
device FireWire port, and the server FireWire port.
7. Reconnect the FireWire device to one of the two FireWire ports on the back panel. If
the front FireWire port is bad, reseat the FireWire cable on the front panel board and
the interconnect board. Replace front panel board. Replace internal FireWire cable.
8. Replace the FireWire cable.
9. Replace the FireWire device.
20 - Xserve Troubleshooting FireWire Devices Symptom Charts

Network Problems
Server cannot be seen on network

1. Open the Network system preference and select the Ethernet option. Verify that you
can now see devices on the network.
2. Boot the server from the Net-install CD. Go to another computer on the same subnet
and start Server Assistant. If the server can be seen, the server hardware should be
functioning correctly. Check the software configuration on the server, or reinstall and
reconfigure the server.
3. Try a known-good Ethernet cable.
4. Clear parameter RAM. Hold down Command-Option-P-R during startup.
5. Try connecting to a known-good Ethernet port at the wall or external hub.
6. Verify that other users are experiencing the same problem. If so, contact the network
administrator.
7. If connected to an Ethernet card, reseat the card.
8. If connected to an Ethernet card, replace the card.
Network Problems Symptom Charts Xserve Troubleshooting - 21

Miscellaneous
ID buttons/lights on the back and front of the server are always on, even
though Server Monitor reports no problems
Make sure the ports and ID button on the back of the logic board align correctly with the
openings in the chassis.
Original Xserve: Security light on the front of the server is always on, even
though the server is unlocked. Or service light turns on and off, even though
Server Monitor does not report any problems.
Make sure the metal locking switch at the front of the server is not bent downward. If it is,
bend it back to its original position, as shown below.
22 - Xserve Troubleshooting Miscellaneous Symptom Charts

 Service Source
Views
Xserve

Internal Views, Xserve
Exploded View
Battery
922-4028
Logic Board
661-2660
Dual-Slot Riser Card Gigabit Ethernet Card
922-5140 661-2677
Video Card, PCI AGP/PCI Single-Slot Riser Card
661-2679 922-5166
AGP/AGP Single-Slot Riser Card
922-5250
DIMM Slots (4) Power Supply

256 MB DDR 661-2664
DIMM
661-2658 1 GHz Uni Processor
512 MB DDR 661-2661
DIMM
661-2659
Drive
Blowers Interconnect
922-5268 Board
922-5167
FireWire Cable
922-5152
CD Drive
661-2663
Optical Drive Cable
922-5151
922-5144
Front Panel Board Front Panel Board Cable
922-5141 922-5153
60 GB Hard Drive Module
661-2654
661-2655
Internal Views, Xserve Xserve Views - 1

Logic Board
Serial USB System FireWire Ethernet

Port Ports Identifier Ports Port
Button
Dual-Slot Riser
Connector
Single-
Slot
Riser
PMU Connector
Reset
Button
Reset
Button
Interrupt
Button
DIMM Power
Slots Supply
Connector
Processor Connector
Bridge Board Connectors
2 - Xserve Views Internal Views, Xserve

External Views, Xserve
Front Panel
Ethernet Card CD Drive

Link Light Open Button
FireWire Port
System Identifier System

Button/Light Activity Lights
Enclosure Lock
Power Button /Light
CD Drive
Apple Drive Modules Bays (4)
Securing Built-In Drive Module Status Light

Thumbscrews (2) Ethernet Drive Module Activity Light
Link Light
Back Panel
System Identifier Button/Light
Gigabit Ethernet Port(s) PCI Card

Expansion Slots (3)
Power Socket
FireWire Ports (2) Monitor Port
USB Ports (2) Serial Console Port
External Views, Xserve Xserve Views - 3

Internal Views,
Xserve (Slot Load)
Exploded View
Battery
922-4028
Logic Board
661-2741
Dual-Slot Riser Card Gigabit Ethernet Card
922-5847 661-2832
Video Card, PCI AGP/PCI Single-Slot Riser Card
661-2679 922-5166
AGP/AGP Single-Slot Riser Card
922-5250
DIMM Slots (4) Power Supply

256 MB DDR 661-2835
DIMM 1.33 GHz Uni Processor
661-2726 661-2833
512 MB DDR 1.33 GHz Multiprocessor
DIMM 661-2834
661-2727
Drive
922-5816 Board
922-5814
FireWire Cable
922-5152
CD Drive
661-2743
Front Bezel 661-2813
922-5822
Optical Drive Cable
922-5151
922-5817
922-5813 922-5815
661-2830
661-2829
4 - Xserve Views Internal Views, Xserve (Slot Load)

Logic Board
Serial USB FireWire System Ethernet

Port Ports Ports Identifier Port
Button
Dual-Slot Riser Single-

Connector Slot
Riser
Connector
PMU
Reset
Button
Reset
Button
Interrupt
Button
Power
DIMM Supply
Slots Connector
Processor Connector
Internal Views, Xserve (Slot Load) Xserve Views - 5

External Views,
Xserve (Slot Load)
Front Panel
System Activity Lights Slot-Load

Ethernet Card Link Light Optical Drive
FireWire 400 Port
Enclosure Lock and Status Light
Apple Drive
Module
(4 Bays)
Power Button /Light Drive Module
Status Light
Securing Thumbscrews (2)
Built-in Ethernet Link Light Drive Module Activity Light
Back Panel
System Identifier
Button/Light
Gigabit Ethernet PCI Card

Port(s) Expansion
Slots (3)
Power
Socket
FireWire 800
Ports (2)
USB Ports (2) VGA Monitor

Serial Console Port
Port
6 - Xserve Views External Views, Xserve (Slot Load)

Internal Views,
Exploded View
Battery
922-4028
Logic Board
Dual-Slot Riser Card 661-2741
922-5847
DIMM Slots (4)

256 MB DDR Power Supply
DIMM 661-2835
661-2726
512 MB DDR
1.33 GHz Multiprocessor
DIMM
661-2834
661-2727
Drive
922-5816 Board
922-5898
FireWire Cable
922-5152
Front Bezel
922-5903

922-5817

922-5813 922-5815

661-2830
Internal Views, Xserve (Cluster Node) Xserve Views - 7

Logic Board
Serial USB FireWire System Ethernet

Port Ports Ports Identifier Port
Button
Dual-Slot Riser Single-

Connector Slot
Riser
Connector
PMU
Reset
Button
Reset
Button
Interrupt
Button
Power
DIMM Supply
Slots Connector
Processor Connector
8 - Xserve Views Internal Views, Xserve (Cluster Node)

External Views,
Front Panel
System Activity Lights
Built-in Ethernet Link Light
FireWire 400 Port
Enclosure Lock and Status Light
Power Button /Light

Securing Thumbscrews (2) Drive Module
Status Light
Drive Module Activity Light
Back Panel
System Identifier
Button/Light
Gigabit Ethernet PCI Card

Port Expansion
Slots (2)
Power
Socket
FireWire 800
Ports (2)
USB Ports (2)

Serial Console
Port
External Views, Xserve (Cluster Node) Xserve Views - 9

 Service Source
Verification of Basic Services

Xserve

How to Start Up From CD
Starting up Xserve from a CD-ROM disc is useful when you need to:
• install the server's operating system
• install a software component
• isolate hardware versus software issues
Preliminary Steps
To start up the server from a CD, you must have physical access to it. You cannot do this
remotely. If you need to start up Xserve using a connected keyboard, you must connect
both a keyboard and monitor before beginning.
Procedure
1. Make sure Xserve is turned off.
2. Turn on Xserve. Quickly eject the CD tray. Insert the Installation CD, and close the CD
tray. Try to perform these steps as quickly as possible.
3. Turn off Xserve.
4. Turn on Xserve again.
5. Press and hold the 'Service ID' button on the front panel of the server until it begins to
start up from the CD. This may take more than 5 seconds.
6. If these steps have worked, Xserve should start up from the CD, and the Installer
Setup assistant should open. Follow the remaining steps only if the server did not start
up in Step 5.
7. Turn off Xserve, and connect a keyboard and monitor to the server.
8. Turn on Xserve while holding down the 'C' key on the keyboard. Xserve should start
up with the CD and the Installer Setup assistant should open.
How to Start Up From CD Xserve Verification of Basic Services - 2

How to Verify the Server's IP
and Hardware (MAC) Address
Verifying the server’s IP and hardware address is useful as a first step in remote software
installation or to verify Xserve hardware and basic network connectivity.
Preliminary Steps
Make sure that the server you want to remotely install software on is started up from the
Installation CD.
Procedure
Option A (Server Assistant)

1. Open Server Assistant from Admin system.
2. Select the "Install Mac OS X Server SW" option. The "remote installation" screen
should appear with a list of all Xserve servers in the subnet.
3. Select the target Xserve from the list. Important: You will need the first 8 characters of
the server's serial number in order to authenticate from this screen.
Option B (Terminal)
1. Open the Terminal application (Applications/Utilities).
2. Type: cd/System/Library/ServerSetup
3. Press Return.
4. Type: ./sa_srchr 224.0.0.1
5. Press Return. The target Xserve's IP address, hardware (MAC) address, and DNS
name (if applicable) should appear.
3 - Xserve Verification of Basic Services How to Verify the Server's IP and Hardware (MAC) Address
How to Discover Xserve on
Your Network
Follow the steps outlined below to remotely administer Xserve.
Note: This procedure verifies basic connectivity to Xserve, which can help isolate
hardware versus software issues.
Preliminary Steps
Make sure that you are doing these steps on an Admin computer with Mac OS X 10.1.5
Server or Mac OS X 10.1.5 remote admin utilities. You must be logged in to that computer
with an Admin account. Also, make sure that the server you want to remotely discover is
started up from the Installer CD.
Procedure
Option A
If you already know your Xserve's IP address you can quickly verify network connectivity
by using the following command from a remote admin system using the Terminal
application:
ping 17.XXX.XXX.XXX (the X characters represent numerical IP addresses)
Or
ping <yourserver.yourdomainname.yourdomainextension>
Your domain extension will resemble something like: .com, .edu, .org
Option B
If you wish to automatically discover your Xserve using the Server Assistant, follow these
steps:
1. Open Server Assistant from a remote admin computer.
2. Select the "Install Mac OS X Server Software" option. The "Remote installation"
screen appears. All Xserve computers on the same TCP/IP subnet appear in a list
format.
3. Select the appropriate Xserve.
How to Discover Xserve on Your Network Xserve Verification of Basic Services - 4

Note: To continue, the first 8 characters of the Xserve serial number are required to
authenticate. The password is case-sensitive. If you encounter difficulty using this
password please see technical document 61644: "Xserve: Initial Password Is Case
Sensitive".
Option C
As an alternative to using Server Assistant, the following procedure may be performed
using the Terminal application.
1. Open the Terminal application on the Admin computer.
2. Type: cd/System/Library/ServerSetup
3. Press Return.
4. Type: ./sa_srchr 224.0.0.1
5. Press Return.
6. Verify that Xserve shows its correct IP address, hardware (MAC) address, and DNS
name (if applicable).
5 - Xserve Verification of Basic Services How to Discover Xserve on Your Network

How to Check for Local Hard
Drive Issues
Follow the steps outlined below if you suspect issues with Xserve's hard disk, and you
have physical access to the server.
Preliminary Steps
In order to follow these steps, you must have physical access to Xserve. You cannot
perform this procedure remotely. A keyboard and monitor must be connected to the server
before you begin. If you wish to check the startup disk (or volume), you must start up
Xserve from its Installation CD first, then open Disk Utility from the first Installation screen.
Procedure
1. Log in to Xserve using the connected keyboard and monitor.
2. Open Disk First Aid, which is located in /Applications/Utilities.
3. Select the volume you wish to examine.
Note: You cannot select the startup volume unless you started up the server from
the Installation CD.
4. Click Verify to check the disk.
5. If there were any issues found by Disk First Aid, answer 'y' to any prompts presented.
6. Repeat steps 4 and 5 until no issues are reported. If Disk First Aid reports the same
error(s) after repeating the process, you should reformat the hard disk.
Warning: Reformatting or reinitializing the hard disk erases all information stored on it.
Make sure you have a backup of all files you may have created and any preinstalled
software that came with Xserve.
How to Check for Local Hard Drive Issues Xserve Verification of Basic Services - 6
How to Remotely Check for
Hard Drive Issues
Follow the steps outlined below if you suspect issues with Xserve's hard disk, and you do
not have physical access to the server.
Preliminary Steps
You must have the server's IP address and Admin (or root) password before performing
this procedure. Xserve's default password is the first 8 characters of its serial number.
Procedure
1. Log in to Xserve.
2. Type: mount
3. Press Return. A list of volumes that are available to the file system appears. Look for
the volume that is at the root level "/". This is the server's startup volume, or
"/dev/rdisk0s10".
4. Type: fsck_hsf -n <insert startup volume path>
For example: fsck_hsf -n /dev/rdisk0s10
5. Press Return. A file system check is performed. This is basically the equivalent of
using Disk First Aid.
6. If "fsck" finds any issues, type 'y' to continue.
7. Repeat steps 4 through 6 until "fsck" finds no errors. If "fsck" reports the same error(s)
after repeating the process, you should reformat the hard disk.
software that came with Xserve
7 - Xserve Verification of Basic Services How to Remotely Check for Hard Drive Issues
How to Erase (Reformat) a Local
Xserve Hard Drive
Follow the steps outlined below if you wish to reformat Xserve's hard disk and you have
physical access to the server.
Preliminary Steps
In order to follow these steps, you must have physical access to Xserve. You cannot
perform this procedure remotely. A keyboard and monitor must be connected to the server
before you begin.
Procedure
1. Start up Xserve from the Installation CD first and open Disk Utility from the first
Installation screen.
2. Click the Erase tab from the Disk Utility screen.
3. Select appropriate options from this screen and click OK to begin reformatting the
hard disk.
How to Erase (Reformat) a Local Xserve Hard Drive Xserve Verification of Basic Services - 8
How to Remotely Erase
(Reformat) a Hard Drive
Follow the steps outlined below if you wish to reformat Xserve's hard disk, and you do not
have physical access to the server.
Preliminary Steps
You must have the server's IP address and Admin (or root) password before performing
this procedure. Xserve's default password is the first 8 characters of its serial number.
Procedure
1. Log in to Xserve.
2. Type: mount
3. Press Return. A list of volumes that are available to the file system appears. Look for
the volume that is at the root level "/". This is the server's startup volume, or "/dev/
rdisk0s10". Note: You cannot reformat the startup volume.
4. Type: umount <insert volume name>
For example: umount Scratch
5. Press Return. This makes the volume unavailable to the file system, or "unmounts" it,
which is required prior to reformatting it.
6. Type: newfs_hfs -v <insert volume name> <insert BSD device name>
For example: newfs_hfs -v Scratch /dev/disk0s11
7. Press Return. The disk is reformatted.
8. Type: shutdown -r now
9. Press Return. Xserver restarts.
9 - Xserve Verification of Basic Services How to Remotely Erase (Reformat) a Hard Drive
How to Verify Xserve Is
Accepting Connections
There are several methods for determining if Xserve has successfully started up and is
providing basic services. Using a terminal connection to accomplish this task provides the
most flexibility.
Note: You will not be able to perform this procedure if the Xserve is not fully started up.
Preliminary Steps
You must have the IP address and an Admin (or root) password of the server you wish to
start up before performing this procedure.
Procedure
1. At the Admin computer, type the following command:
ssh <admin>@<Xserve IP address>
2. You should be presented with a password prompt. At this prompt, type the admin
password. The Xserve's default password is the first 8 characters of the Xserve's
serial number, and is case sensitive.
3. The following should appear if you have logged in correctly:
Welcome To Darwin!
:~] admin%
4. To determine if any additional drives are available to the file system, at the command
prompt type: df
5. To verify more information about the Xserve's volumes, including which volume the
Xserve was actually started up from, open Apple System Profiler from the Terminal
application by typing: AppleSystemProfiler | grep boot
You may also run Apple System Profiler with no options for a complete report of the
Xserve system configuration information.
How to Verify Xserve Is Accepting Connections Xserve Verification of Basic Services - 10

How to Connect Using Server
Monitor
Follow the steps outlined below any time you need to verify that you can remotely
administer Xserve.
Prelimary Steps
You must have the IP address and an Admin (or root) password of the Xserve you wish to
start up before performing this procedure.
Note: Xserve's default password is the first 8 characters of its serial number.
Procedure
1. From the Admin computer, open Server Monitor (/Applications/Utilities).
2. A list of all Xserve servers that have been previously added by Server Monitor
appears.
3. Locate the Xserve you wish to administer from the list.
4. If the Xserve you wish to administer appears in the list, select it, then click the
appropriate tab at the bottom of Server Monitor.
5. If the Xserve you wish to administer does not appear, then click Add Server. Type the
IP address, login name, and password for the Xserve server. The server should
appear in the list. If it does not appear, you may have network or hardware issues.
6. Use the tabs at the bottom of the Server Monitor window to check status of Xserve's
various systems.
Note: If the logic board has been replaced, see technical document 106924: “Xserve: How
to Remotely Install Mac OS X Server After Logic Board Replacement.”
11 - Xserve Verification of Basic Services How to Connect Using Server Monitor

How to Start up the Server Using
an External Drive
Starting up Xserve from an external drive is useful when you need to run diagnostics or
isolate internal CD-ROM drive issues.
Preliminary Steps
In order to start up the server from an external drive, you must have:
• another FireWire drive or system, such as an external FireWire hard drive, or a
Macintosh computer that is capable of starting up using Target Disk Mode (for
example a PowerBook or iBook)
• a version of Xserve software (Mac OS X Server 10.1.5) capable of starting up Xserve
already installed on the external drive
• a keyboard and display connected to server
• physical access to the server
• a keyboard to locally select a volume
Procedure for Local External Drive

1. Make sure that Xserve is turned off.
2. Connect a FireWire cable between the external FireWire drive or computer and
Xserve.
3. Hold down the 'T' key on the keyboard of the external FireWire-capable computer
while it starts up to put it into FireWire Target Disk Mode.
4. Turn on Xserve while holding down the 'Option' key on Xserve's keyboard. The Startup
Manager appears.
5. Select the appropriate drive you wish to start up from in the Startup Manager window,
and then click the right arrow button.
6. Xserve should start up to the external FireWire drive or computer.
Procedure for Remote External Drive

1. Open the Terminal application on a remote computer.
2. Log in as an Admin user on the Xserve.
How to Start up the Server Using an External Drive Xserve Verification of Basic Services - 12
3. Type: bless -folder /Volumes/<your drive name/System/Library/
CoreServices -setOF
4. Press Return.
5. Type: Reboot
6. Press Return.
7. Xserve should start up from the external FireWire drive or computer.
13 - Xserve Verification of Basic Services How to Start up the Server Using an External Drive
Troubleshooting Authentication
Issues
Symptom
A warning message such as “authenticity of host cannot be established” appears when
you attempt to log in to Xserve remotely.
Solution
Delete and then recreate the authentication keys related to the specific host.
Important:
• Make sure you have the IP address and Admin login information for the appropriate
Xserve.
• Verify the first 8 characters of the serial number that correspond to the appropriate
Xserve.
• Make sure that the administration computer has Mac OS X version 10.1 or later
installed.
When authentication of the RSA host key is invalid, the warning message states which
hosts file, and line number within the file, is invalid. For example:
Offending key in /Users/admin/.ssh/known_hosts2:42
In this example, known_hosts2 has the offending authentication key and the host on line
42 of known_hosts2 is the line that needs to be deleted.
Note: The warning message has some very stern wording; however, there are non-
threatening reasons for authentication keys not matching.
Troubleshooting Authentication Issues Xserve Verification of Basic Services - 14

Error message example:
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@
@ WARNING: POSSIBLE DNS SPOOFING DETECTED! @
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@
The RSA host key for xxxxxx has changed,

and the key for the according IP address 17.xxx.xxx.xx
is unchanged. This could either mean that
DNS SPOOFING is happening or the IP address for the host
and its host key have changed at the same time.
Offending key for IP in /Users/admin/.ssh/known_hosts2:44
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@
@ WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED! @
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@
IT IS POSSIBLE THAT SOMEONE IS DOING SOMETHING NASTY!

Someone could be eavesdropping on you right now (man-in-the-middle attack)!
It is also possible that the RSA host key has just been changed.
The fingerprint for the RSA key sent by the remote host is
xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx.
Please contact your system administrator.
Add correct host key in /Users/admin/.ssh/known_hosts2 to get rid of message.
Offending key in /Users/admin/.ssh/known_hosts2:42
RSA host key for xxxxxxx has changed and you have requested strict checking.
The authenticity of host 'xxxxxx (17.xxx.xxx.xx)' can't be established.
RSA key fingerprint is xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx.
Are you sure you want to continue connecting (yes/no)?
15 - Xserve Verification of Basic Services Troubleshooting Authentication Issues

How to Delete and Recreate Authentication Keys
1. Open TextEdit on the Admin computer.
Located in /Applications/
2. Open the file: ~/.ssh/known_hosts or ~/.ssh/known_hosts2
All fingerprints from previous connections appear.
3. Locate host name or IP address of the server within the text you want to connect to
using ssh.
This is the on the line number mentioned in the warning message.
4. Delete the line containing the host name or IP address.
Press Control-K in TextEdit to delete the entire line including all authentication keys
related to this host.
5. Save the TextEdit file.
6. Quit TextEdit.
7. Open Terminal on the Admin computer.
8. Type the following at the command prompt:
ssh -l root <IP Address>
9. Press Return. A prompt asks to recreate the certificate.
10. Type 'y' at the prompt to recreate the certificate.
A new fingerprint appears and a prompt asks to continue with the connection
process.
Troubleshooting Authentication Issues Xserve Verification of Basic Services - 16

Xserve

Uploaded by

Copyright:

Available Formats

Xserve

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Xserve

Uploaded by

Copyright:

Available Formats

 Service Source

Updated: 7 May 2003

© 2003 Apple Computer, Inc. All rights reserved.

© 2003 Apple Computer, Inc. All rights reserved.

General Information Xserve Take Apart - 1

Server Identifier Light/Button

Note: A duplicate identifier light/button is on the server’s back panel.

Before Opening the Server

Unlocking the Server

2 - Xserve Take Apart General Information

1. Shut down the server.

3. Touch the server’s metal case to discharge static electricity.

4. Unplug the power cord.

6. Put on an ESD wrist strap.

General Information Xserve Take Apart - 3

4 - Xserve Take Apart Hard Drive

Hard Drive Xserve Take Apart - 5

6 - Xserve Take Apart Opening the Server

Opening the Server Xserve Take Apart - 7

8 - Xserve Take Apart DIMMs

DIMMs Xserve Take Apart - 9

Dual-Slot Riser Card

Single-Slot Riser Card

10 - Xserve Take Apart PCI or AGP Card

Card in Dual-Slot Riser

Procedure for Card in Dual-Slot Riser

PCI or AGP Card Xserve Take Apart - 11

Procedure for Card in Single-Slot Riser

12 - Xserve Take Apart PCI or AGP Card

4. Disconnect the card from the riser.

PCI or AGP Card Xserve Take Apart - 13

14 - Xserve Take Apart Optical Drive, Xserve

Optical Drive, Xserve Xserve Take Apart - 15

7. Remove the faceplate from the drive.

16 - Xserve Take Apart Optical Drive, Xserve

Optical Drive, Xserve Xserve Take Apart - 17

12. Reconnect the optical drive cable to the drive.

18 - Xserve Take Apart Optical Drive, Xserve

Optical Drive, Xserve (Slot Load) Xserve Take Apart - 19

2. Rotate the optical drive clip clockwise to release it.

4. LIft the drive out of the server.

20 - Xserve Take Apart Optical Drive, Xserve (Slot Load)

Optical Drive, Xserve (Slot Load) Xserve Take Apart - 21

22 - Xserve Take Apart Optical Drive Cable

Optical Drive Cable Xserve Take Apart - 23

24 - Xserve Take Apart Heatsink, Xserve

2. Release the three captive screws that secure the heatsink.

3. Lift the heatsink straight up and remove it from the server.

Heatsink, Xserve Xserve Take Apart - 25

• Replace the heatsink duct on the heatsink.

26 - Xserve Take Apart Heatsink, Xserve

Processor, Xserve Xserve Take Apart - 27

2. Remove the processor from the server.

28 - Xserve Take Apart Processor, Xserve

34 - Xserve Take Apart Blowers

Blowers Xserve Take Apart - 35

36 - Xserve Take Apart ATA Controller Board

ATA Controller Board Xserve Take Apart - 37

38 - Xserve Take Apart ATA Controller Board