1.

Fundamental Concepts & Definition

1. Explain dependent properties and thermodynamic equilibrium. 2. Show that the negative absolute temperature scale is impossible 3. Explain macroscopic and microscopic point of view. 4. Explain briefly the followings:
i) System boundary & surrounding .

ii) Open cycle & closed cycle.

iii) Quasi-Static Process.

5. (i)Explain quasi-static process with p-V diagram. (ii)Explain thermodynamic equilibrium. 6. Show that the thermodynamic temperature scale is independent of working substance. 7. Explain thermodynamic temperature scale. 8. Explain quasi-static process with p-V diagram 9. Explain point function and path function. 10. Write down Vander wall's equation of state. How does it differ from ideal gas equation?

2. First-Law of Thermodynamics
1. Write steady flow energy equation and reduce the same for Turbine, Nozzle,Automobile radiator and throttling device. Clearly sWe the asmn#oris made in each cam. 2. Explain Enthalpy of reaction. 3. What are the requirements of a steady flow process ? 4. Derive the General energy equation for steady flow system and simplify when following systems. (i)Centrifugal water pump (iii) Steam nozzle (ii) Reciprocating air compressor applied for the

(iv) Steam turbine

(v) Gas turbine

5. A turbine, operating under steady flow conditions, receives 4500 Kg. of steam per hour. The steam enters the turbine at a velocity of 2800 m/min, an elevation of 5.5 m and a specific enthalpy

of 2800 KJ/Kg. It leaves the turbine at a velocity of 5600 m/min, an elevation of 1.5 in and a specific enthalpy of 2300 KJ/Kg. Heat losses from the turbine to the surroundings amount to 16,000 KJ/hr. Determine the power output of the turbine. 6. For isothermal flow and non-flow steady processes, Prove that, Jpdv = - Jvdp .Also state the assumptions made. 7. Discuss perpetual motion machines of the first and second kind. 8. What are the limitations of the first law of Thermodynamics. 9. An air standard dual cycle has a compression ratio of 16 bar, and compression begins at 1 bar, 500C. The maximum pressure is 70 bar. The heat transferred to air at a constant pressure is equal to that at constant volume.Calculate:(1) The pressure and temperature at the cardinal points of the cycle. (2) The cycle efficiency. (3) The m.e.p.of the cycle. Take:- Cv=0.718 Kj/Kg K Cp=1.005 Kj/Kg K R=0.278 Kj/Kg K 10. Define & explain the first law of thermodynamics for a closed system undergoing a (i) cyclic process & (ii) non-cyclic process . 11. Explain Phase change processes for pure substance with the help of PT and PV diagrams 12. An air receiver of volume 6 m3 contains air at 16 bar and 40.50C. A valve is opened and some air is allowed to blow out to atmosphere. The pressure of the air in the receiver drops rapidly to 13 bar when the valve is then closed. Calculate the mass of air which has left the receiver. 13. For unsteady flow, derive the energy equation for filling process by Control Volume analysis. 14. Define the specific heat and explain the specific heat at constant volume & constant pressure process. 15. Derive the steady flow energy equation for a single stream entering and leaving a control volume and explain various terms in it. 16. 12 kg of a fluid per minute goes through a reversible steady flow process. The properties of fluid at the inlet are p1 = 1.4 bar, 1 = 25 kg/m3, V1 = 120 m/s & u1 = 920 kJ/kg and at the exit are p2 = 5.6 bar, 2 = 5 kg/m3, V2 = 180 m/s and u2 = 720

kJ/kg. During the passage, the fluid rejects 60 kJ/s and raises through 60m. Determine i) the change in enthalpy ii) work done during the process. 17. Define first law of thermodynamics. Also define internal energy of the system and show that the internal energy is a property of the system. 18. An air receiver of volume 6 m3 contains air at 15 bar and 40.50C. A valve is opened and some air is allowed to blow out to atmosphere. The pressure of the air in the receiver drops rapidly to 12 bar when the valve is then closed. Calculate the mass of air which has left the receiver. 19. Analyze the general equation of the first law of thermodynamics applied to open system.

20. Show that the work transferred by steady flow process is given by Wsf=-fvd p 21. A steam at 6.85 bar and 205C enters in an insulated nozzle with velocity of 50 m/sec. It leaves
at a pressure of 1.35 bar and a velocity of 510 m/sec. Determine the final enthalpy steam.

22. Explain flow work, shaft work and paddle-wheel work transfer.
23. Steam enters a nozzle at a pressure of 7 bar and 20 C and leaves at a pressure of 2 bar. The initial velocity of steam at the entrance is 50m/s and exit velocity from the nozzle is 750 m/s. The mass flow rate through the nozzle is 1500 kg/h. The heat loss from the nozzle is, 12000 kJ/h. Determine the final enthalpy of the steam and nozzle area if the specific volume is 1.25 m3/kg. Take initial enthalpy 2850kJ/kg.

24. A fluid undergoes a reversible adiabatic compression from 1 MPa and 0.3 m3 to
0.05 m3 according to the law pvl transfer and work transfer.
.3

constant. Determine the change in enthalpy,entropy, heat

25. Explain PVT behavior of pure substances with the help of PT and PV diagrams. 26. A centrifugal air :compressor delivers 12 kg of air per minute. The inlet and
conditions of air are: C1=12 m/sec, pi =1 bar, v,=0.5 m3/kg and C2=90 m/sec, P2 =8 bar, v2=0.14 m3lkg. The increase in enthalpy of air passing through the compressor is 150kJ/kg and heat loss to the surroundings is 700 kJ/min.Find: (1) Motor power required to drive the compressor. (2) Ratio of inlet to outlet pipe diameter. Assume that inlet & discharge lines are at the same level.

outlet

3. Second law of thermodynamics

1. State and prove carrot's theorem. 2. A heat engine is operated between 700 C and 30 C. It drives a heat pump which works between 100 C and 30 C. Efficiency and COP of the heat engine and the heat pump are half of that of

corresponding Carnot values. Calculate amount of heat rejected by heat pump' at 100 C when 100 kJ is absorbed by heat engine at700C.

3.10 kg/s of chilled water enters a tall building with velocity of 50 m/s at an elevation of 30 m from ground. The water leaves the system with velocity of 10 m/s at an elevation of 60 m/s. The temperature of water entering in and leaving out are 7 C and 12 C respectively. The rate of work done by pump in the line is 35 kW. Calculate rate of heat removed by water. 4. What are the limitations of Carrot cycle ? Give comparison of Carrot and 5. Write comparison of First and Second law of thermodynamics. 6. Two Carrot engines work in series between the source and sink temperatures of 550 K and 350 K. If both engines develop equal power determine the intermediate temperature. 7. Explain reversible and irreversible process. Give some examples. 8. Prove that no engine working in cycle between, the two reservoirs can be more efficient than a reversible engine working between the same reservoirs. 9. Write the different statements of Second law of thermodynamics & prove their equivalence with neat figures. 10. In a water cooled compressor 0.4 kg/sec of air is compressed. A shaft input of 48 kW is required to run the compressor. Heat lost to the cooling water is 30% of input and 10% of the input is lost in bearings and other frictional effects. Air enters the compressor at 1 bar and 230C. Neglecting the changes in KE & PE, determine the exit air temperature. Take Cp = 1kJ/kg0C air. 11. Show that heat transfer through a finite temperature difference is irreversible. 12. Explain reversible and irreversible process with suitable examples. Write causes of irreversibility. 04 13. State the limitation of the first law of thermodynamics. How the second law of Rankine cycle.

thermodynamics has helped make them clear? Discuss perpetual motion machines of the first and second kind. 14. In a water cooled compressor 0.5 kg of air is compressed/sec. A shaft input of 60 kW is required to run the compressor. Heat lost to the cooling water is 30% of input and 10% of the input is lost in bearings and other frictional effects. Air enters the compressor at 1 bar and 200C.

Neglecting the changes in KE & PE, determine the exit air temperature. Take Cp = 1 kJ/kg 0C for air.
15. There are two ways of increasing the efficiency of a Carnot heat engine:

i) Lowering the temperature T2 of the low temperature reservoir by T, while keeping the temperature T1 of the high temperature reservoir a constant. ii) Increasing the temperature T1 by T, while keeping the temperature T2 a constant. Which is more effective? Prove your answer. 16. A reversible refrigerator operates between 35 C and -12 C. If the heat rejected to 35 C reservoir is 1.3 kW, determine the rate at which to heat is leaking into the refrigerator.
17. Prove the equivalence of Clausius and Kelvin statements.

18. Three carnot Engines Ei,E2,E3 operate between temperatures 1000 K and
calculations for the intermediate temperatures if the work ratio of 4:3:2.

300 K. Make produced by the engines are in the of carnot

19. State and prove camot theorem for heat engine. Also write the statements theorem in the context of refrigerator or heat pump. 20. A heat pump operates between two identical systems; both being at temperature T, to start with. Due to operation of pump, one of the systems gets cooled down to temperature T2.Show that for this operation of pump, the minimum work required by the heat pump is T2 Wmin=C T-+T2-2T,I Where C is the specific heat of the two identical systems
z

21. Prove that all reversible engines working between the two constant temperature reservoirs have the same efficiency. 22. Carnet cycle is not practical. Justify. 23. A heat engine receives 999 kW of heat at constant temperature of 286 C. The rejected at 6 C. The possible heat rejected are (a) (b) 850 kW 490kWand heat is

(c) 400 kW. 24. To get maximum work from two. finite bodies at temperature TI and T2, derive the relevant equation. 25. Gas enters a nozzle at 15 bar and 1500 K with a velocity of 30 m/s. The pressure at the exit of nozzle is 5 bar. If the nozzle efficiency is 90%, calculate the actual exit velocity. Neglect changes in PE and heat exchange between nozzle and surrounding. Take Cp=1.005 kJ/kgK.

26. Prove that the COP of a reversible refrigerator operating between two given temperatures is the maximum. 27. A household refrigerator is maintained at a temperature 2C. Every time door is opened, warm material is placed inside, introducing an average of 420 KJ, but making only a small change in the temperature of the refrigerator. The door is opened 20 times a day and the refrigerator operates at 15% of the ideal COP. The cost of work is 1.50 per kWh. What is the monthly bill for this refrigerator? The atmosphere is at 30C. 28. Why the second law is called a directional law of nature. 29. A heat engine is supplied with 420KJ/cycle of heat at a constant fixed temperature of 327C and heat rejection takes place at 27C.here are no other heat transfers. The following
results were reported.

1.210KJ/cycle heat is rejected 2. 105 K.J/cycle heat is rejected 3. 315 KJ/cycle heat is rejected. Compute the cyclic integral of dQ/T. From these classify which of the results report a reversible cycle or irreversible cycle or impossible cycle. 30. Why the second law is called the law of degradation of energy? 31. An engineer claims to have developed an engine which develops 3.4 kW while consuming 0.44 Kg of fuel of calorific value 41870 kJ / kg in one hour. The maximum and minimum temperatures recorded in the cycle are 1400 C & 350 C respectively. Is the claim of the engineer genuine?

4. Entropy
1. Derive inequality of clausius. 2. 2 kg. of ice at -10 C is exposed to atmosphere at 37 C. The ice melts and comes into thermal equilibrium with atmosphere. Calculate entropy change of the universe. Take Cp of ice = 2 kJ/kg K and latent heat of fusion for ice = 335 kJ/kg. 3. What are the characteristics of Entropy ? Prove that entropy is a property of 4. Derive an expression for the change in entropy of the universe 5. 2 Kg of water at 94 C are mixed with 3 Kg of water at 10 C in an isolated change of entropy due to mixing process. 6. State and prove Clausius theorem. 7. State and explain the Clausius inequality and prove it. system. Calculate the a system.

8. Prove that entropy is a point function and hence a thermodynamic property.

9. 5 kg of water at 30C is mixed with 1 kg of ice at 0C.The process of mixing

is adiabatic and the system is open to atmo sphere. Make calculations for the temperature of mixture and the change of entropy for the spontaneous mixing process. Take specific heat of water= 4.187 kJ/kg k and latent heat of ice=335 kJ/kg.

10. 2 kg of water 94C is mixed with 4 kg of water at 15C in an isolated system

Calculate the changes in entropy due to the mixing process 11.Explain principle of increase of entropy. 12. Show that the internal energy is a property of the system.

5. Availability and Irreversibility

1. Derive the expression for available energy from a finite energy source (heat capacity temperature T when atmosphere temperature is T
o.

,Cp) at

2. Show that due to friction kinetic energy is converted into internal energy and this irreversible.

conversion is

3. Show that there is decrease in available energy when heat is transferred through infinte difference.

temperature

brought in 4. A copper block having heat capacity of 150 kJ/K and temperature of 100 C is contact with an aluminium block having heat capacity 200 kJ/K and temperature of 50 C adiabatically. Calculate irreversibility of the process. Ambient temperature is 37 C. State how these two blocks can be brought into thermal equilibrium reversibly. 5.Explain the concept of decrease in Available energy when heat is transferred through a finite temperature difference with the aid of Temperature - Entropy diagram. 6. Derive an expression for availability of non-flow process. 7. A system at 500 K receives 7200 KJ/min from a source at 1000 K. The temperature of atmosphere is 3000K. Assuming that the temperature of system and source remain constant during heat transfer, find out, (i)The decrease, in Available energy after heat transfer (ii)The entropy produced during heat transfer. 8. Deduce the expression for available energy from a finite energy source at temperature T when

the environmental temperature is To.

9. Calculate the decrease in available energy when 25 Kg of water at 95OC mix with 35 Kg of

water at 35OC, the pressure being taken as constant and the temperature of the surrounding being 15OC. (Cp of water =4.2 KJ/Kg K ) 10. Define available and unavailable energy. Derive an expression for availability of a non-flow

process. 11. A lump of 800 kg of steel at 1250 K is to be cooled to 500 K.If it is desired to use the steel as source of energy, calculate the available and unavailable energies. Take specific heat of steel as 0.5 kJ/kgK and ambient temperature 300 K. 12. What is irreversibility? State various types of irreversibility and explain them.

6. General Thermodynamic Relationships

1. What is the importance of general Thermodynamic relation ? Define co-efficient of volume expansion and isothermal compressibility. 2. State and derive the Maxwells relations 3. Derive the equation

Tds = CV

k 1 dp + C P dv V

4. What is the importance of thermodynamic relations ? Define Helmholtz and Gibbs free energy.
5. Explain thermodynamic equilibrium. 6. Explain the Joule-Kelvin effect with various diagrams. 7. Derive Clapeyron equation and state its practical utility.

7. Properties of Gases and Mixtures

1. What is Joule-Thomson coefficient? Explain and show that it is zero for an

ideal gas.
2. Define the Perfect and real gases. 3. Explain the Daltons law of Partial Pressure & Partial Volume.