SLC Wiring Manual

Intelligent Control Panel
SLC
Wiring Manual
Document 51309 10/12/2011 Rev:

P/N 51309:P1
ECN 11-788
P1
Fire Alarm System Limitations

While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance!
An automatic fire alarm systemtypically made up of smoke detectors, heat detectors, manual pull stations, audible warning devices, and a fire alarm control panel with remote notification capabilitycan provide early warning of a developing fire. Such a system, however, does not assure protection against property damage or loss of life resulting from a fire. The Manufacturer recommends that smoke and/or heat detectors be located throughout a protected premise following the recommendations of the National Fire Protection Association Standard 72 (NFPA 72), manufacturer's recommendations, State and local codes, and the recommendations contained in the Guides for Proper Use of System Smoke Detectors, which are made available at no charge to all installing dealers. These documents can be found at http://www.systemsensor.com/html/applicat.html. A study by the Federal Emergency Management Agency (an agency of the United States government) indicated that smoke detectors may not go off in as many as 35% of all fires. While fire alarm systems are designed to provide early warning against fire, they do not guarantee warning or protection against fire. A fire alarm system may not provide timely or adequate warning, or simply may not function, for a variety of reasons: Smoke detectors may not sense fire where smoke cannot reach the detectors such as in chimneys, in or behind walls, on roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level or floor of a building. A second-floor detector, for example, may not sense a firstfloor or basement fire. Particles of combustion or smoke from a developing fire may not reach the sensing chambers of smoke detectors because: Barriers such as closed or partially closed doors, walls, or chimneys may inhibit particle or smoke flow. Smoke particles may become cold, stratify, and not reach the ceiling or upper walls where detectors are located. Smoke particles may be blown away from detectors by air outlets. Smoke particles may be drawn into air returns before reaching the detector. Heat detectors do not sense particles of combustion and alarm only when heat on their sensors increases at a predetermined rate or reaches a predetermined level. Rate-of-rise heat detectors may be subject to reduced sensitivity over time. For this reason, the rate-of-rise feature of each detector should be tested at least once per year by a qualified fire protection specialist. Heat detectors are designed to protect property, not life. IMPORTANT! Smoke detectors must be installed in the same room as the control panel and in rooms used by the system for the connection of alarm transmission wiring, communications, signaling, and/or power. If detectors are not so located, a developing fire may damage the alarm system, crippling its ability to report a fire. Audible warning devices such as bells may not alert people if these devices are located on the other side of closed or partly open doors or are located on another floor of a building. Any warning device may fail to alert people with a disability or those who have recently consumed drugs, alcohol or medication. Please note that: Strobes can, under certain circumstances, cause seizures in people with conditions such as epilepsy. Studies have shown that certain people, even when they hear a fire alarm signal, do not respond or comprehend the meaning of the signal. It is the property owner's responsibility to conduct fire drills and other training exercise to make people aware of fire alarm signals and instruct them on the proper reaction to alarm signals. In rare instances, the sounding of a warning device can cause temporary or permanent hearing loss.
A fire alarm system will not operate without any electrical power. If AC power fails, the system will operate from standby batteries only for a specified time and only if the batteries have been properly maintained and replaced regularly. Equipment used in the system may not be technically compatible with the control panel. It is essential to use only equipment listed for service with your control panel. Telephone lines needed to transmit alarm signals from a premise to a central monitoring station may be out of service or temporarily disabled. For added protection against telephone line failure, backup radio transmission systems are recommended. The most common cause of fire alarm malfunction is inadequate maintenance. To keep the entire fire alarm system in excellent working order, ongoing maintenance is required per the manufacturer's recommendations, and UL and NFPA standards. At a minimum, the requirements of NFPA 72 shall be followed. Environments with large amounts of dust, dirt or high air velocity require more frequent maintenance. A maintenance agreement should be arranged through the local manufacturer's representative. Maintenance should be scheduled monthly or as required by National and/or local fire codes and should be performed by authorized professional fire alarm installers only. Adequate written records of all inspections should be kept.
Limit-C1-2-2007
The amount of smoke present may be insufficient to alarm smoke detectors. Smoke detectors are designed to alarm at various levels of smoke density. If such density levels are not created by a developing fire at the location of detectors, the detectors will not go into alarm. Smoke detectors, even when working properly, have sensing limitations. Detectors that have photoelectronic sensing chambers tend to detect smoldering fires better than flaming fires, which have little visible smoke. Detectors that have ionizing-type sensing chambers tend to detect fast-flaming fires better than smoldering fires. Because fires develop in different ways and are often unpredictable in their growth, neither type of detector is necessarily best and a given type of detector may not provide adequate warning of a fire. Smoke detectors cannot be expected to provide adequate warning of fires caused by arson, children playing with matches (especially in bedrooms), smoking in bed, and violent explosions (caused by escaping gas, improper storage of flammable materials, etc.).
FireLite SLC Wiring Manual P/N 51309:P1 10/12/2011
Installation Precautions
Adherence to the following will aid in problem-free installation with long-term reliability:
WARNING - Several different sources of power can be connected to the fire alarm control panel. Disconnect all sources of power before servicing. Control unit and associated equipment may be damaged by removing and/or inserting cards, modules, or interconnecting cables while the unit is energized. Do not attempt to install, service, or operate this unit until manuals are read and understood. CAUTION - System Re-acceptance Test after Software Changes: To ensure proper system operation, this product must be tested in accordance with NFPA 72 after any programming operation or change in site-specific software. Reacceptance testing is required after any change, addition or deletion of system components, or after any modification, repair or adjustment to system hardware or wiring. All components, circuits, system operations, or software functions known to be affected by a change must be 100% tested. In addition, to ensure that other operations are not inadvertently affected, at least 10% of initiating devices that are not directly affected by the change, up to a maximum of 50 devices, must also be tested and proper system operation verified. This system meets NFPA requirements for operation at 0-49 C/32-120 F and at a relative humidity 93% 2% RH (noncondensing) at 32C 2C (90F 3F). However, the useful life of the system's standby batteries and the electronic components may be adversely affected by extreme temperature ranges and humidity. Therefore, it is recommended that this system and its peripherals be installed in an environment with a normal room temperature of 15-27 C/60-80 F. Verify that wire sizes are adequate for all initiating and indicating device loops. Most devices cannot tolerate more than a 10% I.R. drop from the specified device voltage. Like all solid state electronic devices, this system may operate erratically or can be damaged when subjected to lightning induced transients. Although no system is completely immune from lightning transients and interference, proper grounding will reduce susceptibility. Overhead or outside aerial wiring is not recommended, due to an increased susceptibility to nearby lightning strikes. Consult with the Technical Services Department if any problems are anticipated or encountered. Disconnect AC power and batteries prior to removing or inserting circuit boards. Failure to do so can damage circuits. Remove all electronic assemblies prior to any drilling, filing, reaming, or punching of the enclosure. When possible, make all cable entries from the sides or rear. Before making modifications, verify that they will not interfere with battery, transformer, or printed circuit board location. Do not tighten screw terminals more than 9 in-lbs. Overtightening may damage threads, resulting in reduced terminal contact pressure and difficulty with screw terminal removal. This system contains static-sensitive components. Always ground yourself with a proper wrist strap before handling any circuits so that static charges are removed from the body. Use static suppressive packaging to protect electronic assemblies removed from the unit. Follow the instructions in the installation, operating, and programming manuals. These instructions must be followed to avoid damage to the control panel and associated equipment. FACP operation and reliability depend upon proper installation.
Precau-D1-9-2005
FCC Warning
WARNING: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications. It has been tested and found to comply with the limits for class A computing devices pursuant to Subpart B of Part 15 of FCC Rules, which is designed to provide reasonable protection against such interference when devices are operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user will be required to correct the interference at his or her own expense. Canadian Requirements This digital apparatus does not exceed the Class A limits for radiation noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le present appareil numerique n'emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la classe A prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada.
LiteSpeed is a trademark; and FireLite Alarms is a registered trademark of Honeywell International Inc. Microsoft and Windows are registered trademarks of the Microsoft Corporation. 2011 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited.
Software Downloads
In order to supply the latest features and functionality in fire alarm and life safety technology to our customers, we make frequent upgrades to the embedded software in our products. To ensure that you are installing and programming the latest features, we strongly recommend that you download the most current version of software for each product prior to commissioning any system. Contact Technical Support with any questions about software and the appropriate version for a specific application.
Documentation Feedback
Your feedback helps us keep our documentation up-to-date and accurate. If you have any comments or suggestions about our online Help or printed manuals, you can email us. Please include the following information: Product name and version number (if applicable) Printed manual or online Help Topic Title (for online Help) Page number (for printed manual) Brief description of content you think should be improved or corrected Your suggestion for how to correct/improve documentation Send email messages to: FireSystems.TechPubs@honeywell.com Please note this email address is for documentation feedback only. If you have any technical issues, please contact Technical Services.
Table of Contents
Section 1: Introduction............................................................................................................. 8
1.1: Scope..............................................................................................................................................................8 1.1.1: Reference Documentation ...................................................................................................................9 1.2: Overview......................................................................................................................................................10 1.3: Polling Protocols .........................................................................................................................................10 1.3.1: Available Protocols............................................................................................................................10 1.3.2: Protocol Use ......................................................................................................................................10 1.4: Devices ........................................................................................................................................................11 1.4.1: Isolator Module..................................................................................................................................11 1.4.2: Monitor Modules ...............................................................................................................................11 1.4.3: Control Modules ................................................................................................................................11 1.4.4: Relay Modules...................................................................................................................................11 1.4.5: Multiple Input/Output Modules.........................................................................................................11 1.4.6: Intelligent Detectors ..........................................................................................................................11 1.4.7: Manual Pull Station ...........................................................................................................................12 1.4.8: 300 Series Addressable Devices........................................................................................................12 1.5: SLC Capacity...............................................................................................................................................12 1.6: SLC Performance.........................................................................................................................................13 1.7: Surge Suppression........................................................................................................................................13 1.8: LED Operation.............................................................................................................................................13
Section 2: Wiring Requirements............................................................................................ 14

2.1: Wire Sizing ..................................................................................................................................................14 2.1.1: CLIP (Classic Loop Interface Protocol) Mode..................................................................................14 2.1.2: LiteSpeed Mode.................................................................................................................................14 2.2: Measuring Resistance & Length..................................................................................................................15 2.2.1: Two-Wire SLC - Style 4 (Class B)....................................................................................................15 2.2.2: Four-Wire SLC Style 6 & 7 (Class A) ..............................................................................................16 2.3: Shield Wire Termination..............................................................................................................................17 2.4: Control Panel Terminal Blocks....................................................................................................................18 2.4.1: MS-9200 ............................................................................................................................................18 2.4.2: MS-9600, MS-9600LS, & MS-9600UDLS.......................................................................................18 2.4.3: MS-9200UDLS (Software Version 3.0)............................................................................................19 2.4.4: MS-9200UD & MS-9200UDLS (Versions 1 and 2) .........................................................................19 2.4.5: MS-9050UD ......................................................................................................................................20
Section 3: SLC Circuits without Isolators ............................................................................ 21

3.1: Overview......................................................................................................................................................21 3.2: NFPA Style 4 SLC .......................................................................................................................................21 3.3: NFPA Style 6 SLC .......................................................................................................................................22
Section 4: SLC Circuits with Isolators .................................................................................. 23

4.1: Fault Isolator Devices ..................................................................................................................................23 4.1.1: Isolating an SLC Branch....................................................................................................................23 4.1.2: Wiring an Isolator Module ................................................................................................................23 4.2: NFPA Style 4 SLC Using Isolator Modules ................................................................................................24 4.3: NFPA Style 6 SLC Using Isolator Modules ................................................................................................25 4.4: NFPA Style 7 SLC Using Isolator Modules ................................................................................................26
Section 5: Monitor Modules ................................................................................................... 27

5.1: Descriptions .................................................................................................................................................27 5.1.1: Addressable Monitor Modules ..........................................................................................................27 5.1.2: Zone Interface Modules.....................................................................................................................29 5.1.3: Dual Monitor Module........................................................................................................................31 5.1.4: Mini Monitor Module........................................................................................................................31
Table of Contents
5.2: Installation....................................................................................................................................................31 5.2.1: Setting an SLC address for a Single Point Module ...........................................................................32 5.2.2: Setting an SLC address for a Multi-Point Module ............................................................................33 5.3: MMF-300 Wiring Diagrams ........................................................................................................................34 5.3.1: Wiring a NFPA Style B IDC with an MMF-300...............................................................................34 5.3.2: Wiring a NFPA Style D IDC with an MMF-300 ..............................................................................35 5.3.3: MMF-300 Wiring for Emergency Alarm System Applications ........................................................36 5.4: MMF-300-10 Wiring Diagrams...................................................................................................................37 5.4.1: Wiring a NFPA Style B IDC with an MMF-300-10 .........................................................................37 5.4.2: Wiring a NFPA Style D IDC with an MMF-300-10 .........................................................................38 5.5: MDF-300 Wiring Diagrams.........................................................................................................................39 5.5.1: Wiring a NFPA Style B IDC with an MDF-300 ...............................................................................39 5.6: MMF-302 Wiring Diagrams ........................................................................................................................40 5.6.1: Wiring a NFPA Style B IDC with an MMF-302...............................................................................40 5.6.2: Wiring a NFPA Style D IDC with an MMF-302 ..............................................................................41 5.7: MMF-302-6 Wiring Diagrams.....................................................................................................................42 5.7.1: Wiring a NFPA Style B IDC with an MMF-302-6 ...........................................................................42 5.7.2: Wiring a NFPA Style D IDC with an MMF-302-6 ...........................................................................43
Section 6: Control Modules ................................................................................................... 44

6.1: Description ...................................................................................................................................................44 6.2: CMF-300 Installation...................................................................................................................................44 6.2.1: Setting an SLC address for a CMF-300 Module ...............................................................................44 6.2.2: Wiring a Notification Appliance Circuit (NAC) with a CMF-300....................................................44 6.3: Wiring a CMF-300 Module .........................................................................................................................45 6.3.1: Wiring a Style Y NAC (Two-Wire) with Addressable Control Modules .........................................45 6.3.2: Wiring a Style Z NAC (Four-Wire) with Addressable Control Modules .........................................46 6.4: CMF-300-6 Installation ...............................................................................................................................46 6.4.1: Cabinet Installation ............................................................................................................................46 6.4.2: Setting an SLC address for an CMF-300-6 Module ..........................................................................46 6.4.3: Setting NACs as Style Y or Style Z...................................................................................................47 6.4.4: Disabling Unused Module Addresses................................................................................................47 6.4.5: Short Circuit Protection .....................................................................................................................47 6.4.6: Features Not Supported .....................................................................................................................48 6.4.7: Circuit Board Information .................................................................................................................48 6.5: Wiring a CMF-300-6 Module ......................................................................................................................49 6.5.1: Wiring a Style Y NAC (Two-Wire) .................................................................................................49 6.5.2: Wiring a Style Z NAC (Four-Wire)...................................................................................................50
Section 7: Relay Modules ...................................................................................................... 51

7.1: Description ...................................................................................................................................................51 7.2: CRF-300 Installation & Wiring ...................................................................................................................51 7.2.1: Setting an SLC address for a CRF-300 Module ................................................................................51 7.2.2: Wiring a CRF-300 Module (Form-C Relay) ....................................................................................51 7.3: CRF-300-6 Circuit Board Information .......................................................................................................52 7.4: CRF-300-6 Installation & Wiring ................................................................................................................52 7.4.1: Cabinet Installation ............................................................................................................................52 7.4.2: Setting an SLC address for a CRF-300-6 Module.............................................................................53 7.4.3: Disabling Unused Module Addresses................................................................................................53 7.4.4: Wiring a CRF-300-6 Module (Form-C Relay) ..................................................................................53
Section 8: Multiple Input/Output Modules............................................................................ 54

8.1: Description ...................................................................................................................................................54 8.2: CDRM-300 Installation & Wiring ...............................................................................................................54 8.2.1: Setting an SLC address for a CDRM-300 Module ............................................................................54 8.2.2: Wiring a CDRM-300 Module (Form-C Relay) ................................................................................55
Table of Contents
Section 9: Intelligent Detector Bases.................................................................................... 56

9.1: Description...................................................................................................................................................56 9.2: Installation and Wiring ................................................................................................................................56 9.2.1: Setting the Detector Address .............................................................................................................56 9.2.2: Wiring a Detector Base......................................................................................................................57 9.2.3: Wiring an Isolator Base .....................................................................................................................58 9.2.4: Wiring a Relay Base ..........................................................................................................................58 9.2.5: Wiring a Sounder Base ......................................................................................................................59
Section 10: Addressable Manual Pull Station ...................................................................... 60

10.1: Description.................................................................................................................................................60 10.2: Installation .................................................................................................................................................60 10.2.1: Setting an SLC address....................................................................................................................60 10.2.2: Wiring a Manual Pull Station ..........................................................................................................60
Appendix A: Power Considerations...................................................................................... 61

A.1: Supplying Power to 24 VDC Detectors and NACs ....................................................................................61 A.1.1: Resistance and Size...........................................................................................................................61 A.2: Supervising 24 VDC Power........................................................................................................................62
Appendix B: Surge Suppression........................................................................................... 64

B.1: Introduction .................................................................................................................................................64 B.2: Installation...................................................................................................................................................64 B.2.1: Wiring Diagram for MS-9200 ..........................................................................................................65 B.2.2: Wiring Diagram for MS-9600, MS-9600LS, MS-9600UDLS, MS-9200UD, MS-9200UDLS, and MS-9050UD ................................................................................................................................................66
Appendix C: Terminal Conversion Charts for New & Legacy Devices.............................. 67

C.1: CRF-300......................................................................................................................................................67 C.2: CMF-300 and MMF-302 ............................................................................................................................68 C.3: MMF-300 ....................................................................................................................................................69 C.4: MDF-300.....................................................................................................................................................70
Appendix D: Intelligent Detector Base Layouts for Legacy Devices ................................. 71

D.1: B350LP or B501 Detector Base..................................................................................................................71 D.2: B224BI Isolator Base.................................................................................................................................72 D.3: B224RB Relay Base ...................................................................................................................................72 D.4: B501BH(-2) and B501BHT(-2) Sounder Bases .........................................................................................73
Appendix E: Canadian Versions of SLC Devices ................................................................ 74 Index........................................................................................................................................ 76
Section 1: Introduction
1.1 Scope
This document describes the operation, installation and wiring of various Signaling Line Circuit (SLC) devices when used with the Fire-Lite MS-9200/MS-9200E, MS-9600/MS-9600E, MS9600LS/MS-9600LSC/MS-9600LSE, MS-9600UDLS/MS-9600UDLSE, MS-9200UD/MS9200UDE, MS-9200UDLS/MS-9200UDLSE/MS-9200UDLSC, and MS-9050UD/MS9050UDC/MS-9050UDE control panels. It also provides basic information that applies to FireLite SLC loops in general, such as the branch resistance measurements.
NOTE: Any reference in this manual to the MS-9200, MS-9200UD, MS-9200UDLS, MS-9600, MS-9600LS, MS-9600UDLS, or MS-9050UD includes the MS-9200E, MS-9200UDE, MS-9200UDLSE, MS-9200UDLSC, MS-9600E, MS-9600LSE, MS-9600LSC, MS-9600UDLSE, MS-9050UDC, or MS-9050UDE respectively unless otherwise specified.
Additional information about the specific control panel and the modules and detectors referenced in this document can be found in the respective installation manual as listed in Table 1.1, Reference Documentation, on page 10. Currently, there are two styles of modules available, legacy version and newer version. The obvious difference between the two styles is the orientation of the rotary dials. Refer to the diagram below for an example of each.
CMF-300 Legacy Version Module (Vertical Rotary Dial)
CMF-300 Newer Version Module (Horizontal Rotary Dial)
NOTE: Only the MMF-300, MMF-302, CRF-300, CMF-300, and MDF-300 modules are available as newer type modules. Both the legacy and newer versions share the same part numbers. The newer version modules will be phased in, replacing the legacy version. This manual contains information and wiring diagrams for the newer version of the modules. Refer to Terminal Conversion Charts for New & Legacy Devices on page 67 for additional information.
Scope
Introduction
Currently, there are two styles of detector bases available, legacy version and newer version. The obvious difference between the two styles is the orientation of the screw terminals. Refer to Section 9 and Appendix D for an illustration of each.
NOTE: Only the B501 Detector Base, B210LP Detector Base (replacement base for B350LP), B224RB Relay Base, and B224BI Isolator Base are available as newer type bases. Both the legacy and newer versions share the same part numbers. The newer version bases will be phased in, replacing the legacy version. This manual contains information and wiring diagrams for the newer version of the bases. Refer to Intelligent Detector Base Layouts for Legacy Devices on page 71 for additional information.
1.1.1 Reference Documentation

The table below accommodates a list of document sources containing additional information regarding the devices used on a Signaling Line Circuit:
For information on... MS-9200/MS-9200E MS-9600/MS-9600E MS-9200UD/MS-9200UDE MS-9200UDLS/MS-9200UDLSE/MS-9200UDLSC MS-9600LS/MS-9600LS(C/E) & MS-9600UDLS/MS9600UDLSE MS-9050UD/MS-9050UDC/MS-9050UDE Compatible Devices BG-12LX Pull Station MMF-300 Monitor Module MMF-300-10 Monitor Module MMF-301 Mini Monitor Module MMF-302 Monitor Module MMF-302-6 Interface Module MDF-300 Dual Monitor Module CMF-300 Control Module CMF-300-6 Control Module CRF-300 Relay Module CRF-300-6 Relay Module CDRM-300 Multiple Input/Output Module I300 Isolator Module AD350 Multicriteria Detector AD355 Multicriteria Detector SD350 & SD350T Photo Detector SD355 & SD355T Photo Detector CP350 Ionization Detector CP355 Ionization Detector H350 Heat Detector H350R Heat Detector w/ROR H355 Heat Detector (135) H355R Heat Detector w/ROR H355HT Heat Detector (190) D350P Duct Detector D350PL(A) Duct Detector - low flow D350RP Duct Detector w/Relay D350RPL(A) Duct Detector w/Relay - low flow D355PL Duct Detector - low flow Refer to... Instruction Manual Instruction Manual Instruction Manual Instruction Manual Instruction Manual Instruction Manual Device Compatibility Document Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Part Number 51003 51335 51906 52750 52646 52413 15384 I56-3655 I56-1191 / I56-3653 I56-1873 I56-1193 / I56-3654 I56-1192 / I56-3652 I56-1900 I56-0013 / I56-3665 I56-1189 / I56-3650 I56-1874 I56-1190 / I56-3651 I56-1875 I56-3726 I56-1381 F300-17-00 I56-3660 I56-0035 I56-3660 I56-0036 I56-3656 I56-0038 I56-0037 I56-3657 I56-3657 I56-3657 F300-10-00 I56-1975 I56-0047 I56-1974 I56-3255
Introduction
For information on... BEAM355(S) Addressable Beam Detector B210LP Plug-in Detector Base B501 Detector Base B501BH Sounder Detector Base B501BH-2 Sounder Detector Base B501BHT Temporal Sounder Detector Base B501BHT-2 Temporal Sounder Detector Base B200SR Sounder Detector Base B224RB Relay Detector Base B224BI Isolator Detector Base Refer to... Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions
Overview
Part Number I56-2425 I56-3739 I56-0357 / I56-3738 I56-0491 I56-2813 I56-1367 I56-2819 I56-3387 I56-2815 / I56-3737 I56-0725 / I56-3736
Table 1.1 Reference Documentation
1.2 Overview
Communication between the control panel and intelligent addressable monitor and control devices takes place through a Signaling Line Circuit (SLC), which can be wired to meet the requirements of NFPA Style 4, Style 6, or Style 7. At least one secondary surge protector must be used with each SLC wiring pair whenever SLC wiring runs outside the building. For detailed information refer to Surge Suppression on page 64.
1.3 Polling Protocols

The MS-9200UDLS, MS-9600LS, and MS-9600UDLS support LiteSpeed protocol or Classic Loop Interface Protocol (CLIP). The MS-9200/E, MS-9600/E, MS-9200UD/E, and MS-9050UD support Classic Loop Interface Protocol (CLIP) only.
1.3.1 Available Protocols

LiteSpeed is a communication protocol that greatly enhances the speed of communication between analog intelligent devices. Only the MS-9200UDLS, MS-9600LS, and MS-9600UDLS are capable of operating in LiteSpeed mode. This is the default mode of operation for these FACPs. CLIP (Classic Loop Interface Protocol) polls devices in sequential order. All Fire-LiteFireWarden addressable fire alarm control panels can operate in CLIP mode. This is the default mode of operation for all other FACPs.
1.3.2 Protocol Use

Use one of the following options with LiteSpeed/CLIP mode: 1. 2. Program all modules and detectors on an FACP as LiteSpeed. Program all modules and detectors on an FACP as CLIP.
NOTE: FACPs with more than one SLC loop must be programmed for only LiteSpeed or CLIP mode of operation. Communication protocols cannot be split between SLC loops.
When switching between polling protocols, the loop circuit must be powered down for at least 30 seconds to reset the devices.
10
Devices
Introduction
1.4 Devices
1.4.1 Isolator Module
The I300 Isolator Module permits a zone of detectors and modules to be fault isolated from the remainder of the SLC loop, allowing critical components to function in the event of a circuit fault. Isolator modules are required to meet the requirements of an NFPA Style 7 circuit.
1.4.2 Monitor Modules

Addressable modules that allow the control panel to monitor entire circuits of conventional alarm initiating devices, such as manual pull stations, smoke detectors, heat detectors, waterflow and supervisory devices. MMF-300 - Monitors a Style B (Class B) or Style D (Class A) circuit of dry-contact input devises. MMF-300-10 - Monitors ten (10) Style B (Class B) or five (5) Style D (Class A) normally open contact device circuits. MMF-301 - Same as the MMF-300 except offered in a smaller package for mounting with Style B wired devices. This module does not have an LED. MMF-302 - Monitors a single IDC of two-wire smoke detectors. MMF-302-6 - An addressable module that provides an interface between the control panel and six (6) Style B (Class B) or three (3) Style D (Class A) IDCs of two-wire smoke detectors. MDF-300 - Similar to MMF-300, but provides for two independent Style B IDCs.
1.4.3 Control Modules

Through the CMF-300 addressable control module, the control panel can selectively activate a Notification Appliance Circuit (NAC). CMF-300-6 - Similar in operation to the CMF-300, except it can activate six (6) Style Y (Class B) or three (3) Style Z (Class A) NACs.
1.4.4 Relay Modules

The CRF-300 addressable relay module provides the control panel with a dry-contact output for activating a variety of auxiliary devices. CRF-300-6 - Similar in operation to the CRF-300, except it provides six (6) Form-C relays.
1.4.5 Multiple Input/Output Modules

The CDRM-300 addressable multiple input/output module monitors two (2) Style B input devices and provides two (2) independent Form-C relay contacts.
1.4.6 Intelligent Detectors

AD350 - A multicriteria smoke sensor that combines a photoelectric sensing chamber and 135F (57.2C) fixed temperature heat detection. The sensor uses addressable communication to transmit smoke density and other information to the control panel. It adjusts its detection parameters and alarm threshold depending on the ambient conditions it samples in its environment. AD355 - A multicriteria smoke sensor that combines a photoelectric sensing chamber and 135F (57.2C) fixed temperature heat detection. The sensor uses addressable communication to transmit smoke density and other information to the control panel. It adjusts its detection parameters and alarm threshold depending on the ambient conditions it samples in its environment. CP350 - An addressable ionization smoke detector which measures the level of combustion products in its chamber using the ionization principle.
FireLite SLC Wiring Manual P/N 51309:P1 10/12/2011 11
Introduction
SLC Capacity
CP355 - An addressable ionization smoke detector which measures the level of combustion products in its chamber using the ionization principle. D350P - An addressable photoelectric duct detector. The D350RP includes an alarm relay. Air velocity rating is 500 to 4,000 feet per minute. D350PL -An addressable low flow photoelectric duct detector (D350PLA for Canada). The D350RPL includes an alarm relay (D350RPLA for Canada). Low Flow refers to the air velocity rating of 100 to 4,000 feet per minute (0.5 to 20.32 m/sec). D355PL - An addressable non-relay photoelectric low flow smoke detector. Low Flow refers to the air velocity rating of 100 to 4,000 feet per minute (0.5 to 20.32 m/sec). H3501 - An addressable detector using a thermistor sensing circuit for fast response. H350R incorporates a thermal rate of rise of 15F (9.4C)/minute. H3551 - An addressable 135 fixed temperature heat detector using a thermistor sensing circuit for fast response. H355R incorporates a thermal rate of rise of 15 F (9.4 C)/minute. H355HT1 - An addressable 190 fixed temperature heat detector using a thermistor sensing circuit for fast response. SD350 - An addressable photoelectric smoke detector which provides smoke sensing utilizing optical sense technology. The SD350T includes a 135 F fixed thermal sensor. SD355 - An addressable photoelectric smoke detector which provides smoke sensing utilizing optical sense technology. The SD355T includes a 135 F fixed thermal sensor. The SD355R is a low profile, intelligent, photoelectric sensor that is remote test capable. BEAM355 - An addressable long range projected beam smoke detector designed to provide open area protection. The BEAM355S has an integral sensitivity test feature that consists of a test filter attached to a servomotor inside the detector optics. DNR(W) - Innovair Flex, intelligent, non-relay, low flow, photoelectric duct detector housing. This requires the SD355R photoelectric smoke detector. Accomodates the installation of the CRF300 relay module. The DNRW is a watertight housing.
1.4.7 Manual Pull Station

The BG-12LX is a dual-action pull station that, when activated, provides an addressable identification and its location to the control panel. An addressable monitor module is mounted inside the pull station to facilitate servicing and replacement.
1.4.8 300 Series Addressable Devices

FireLites 300 Series of addressable devices are fully compatible with the MS-9200, MS-9200UD, MS-9200UDLS, MS-9600, MS-9600LS(C/E), MS-9600UDLS/E, and MS-9050UD FACPs. The devices must be configured for CLIP (Classic Loop Interface Protocol) Mode operation. The address of 300 series devices cannot be set above 99. Compatible devices include:
SD300 Photo SD300T Photo w/Thermal CP300 Ionization BG-10LX Pull Station M300 Monitor Module M301 Mini Monitor Module M302 2-wire Monitor Module C304 Control/Relay Module
1.5 SLC Capacity

The protocol selected for an SLC loop determines the maximum number of devices that can be handled by the loop. See Section 1.3, Polling Protocols, on page 10. Within those limits, the individual control panel may have additional restrictions. See the specific installation manual for this information.
1. Addressable Heat Detectors are not compatible with the MS-9200(E).

12 FireLite SLC Wiring Manual P/N 51309:P1 10/12/2011
SLC Performance
Introduction
1.6 SLC Performance

SLC performance depends on the type of circuit (Style 4, Style 6, or Style 7) and the components on the circuit.
NOTE: SLC operation meeting Style 7 requirements isolates each device on the SLC from faults that may occur within other areas of the SLC.
Wiring style requirements are determined by national and local codes. Consult with the Authority Having Jurisdiction before wiring the SLC. The table below (derived from NFPA 72-1999) lists the trouble conditions that result when a fault exists on an SLC.
Type of Fault Single Open Single Ground Short Short and open Short and ground Open and ground Communications loss Style 4 Trouble Alarm, Trouble (ground) Trouble Trouble Trouble Trouble Trouble Style 6 Alarm, Trouble Alarm, Trouble (ground) Trouble Trouble Trouble Alarm, Trouble Trouble Style 7 Alarm, Trouble Alarm, Trouble (ground) Alarm, Trouble Trouble Alarm, Trouble Alarm, Trouble Trouble
Trouble - The control panel will indicate a trouble condition for this type of fault. Alarm - The control panel must be able to process an alarm input signal in the presence of this type of fault.
Table 1.2 SLC Performance
1.7 Surge Suppression

One primary surge protector must be used with each SLC wiring pair whenever SLC wiring runs outside the building. For detailed information refer to Surge Suppression on page 64.
1.8 LED Operation

The table below lists the LED operation on the various devices on an SLC.
Device Monitor Module Control Module Detector Standby Blinks RED Blinks GREEN Blinks RED Activated Steady RED Steady GREEN Steady RED
Table 1.3 LED Operation
13
Section 2: Wiring Requirements

2.1 Wire Sizing
The SLC requires use of a specific wire type, depending on the mode of operation, to ensure proper circuit functioning. Wire size should be no smaller than 18 AWG (0.75 mm2) and no larger than 12 AWG (3.25 mm2) wire. The wire size depends on the length of the SLC circuit. It is recommended that all SLC wiring be twisted-pair to minimize the effects of electrical interference.
2.1.1 CLIP (Classic Loop Interface Protocol) Mode

All addressable FACPs can operate in CLIP (Classic Loop Interface Protocol) mode. It is recommended that all SLC wiring be twisted-pair and shielded when operating in CLIP mode to reduce the effects of electrical interference. Use the table below to determine the specific wiring requirements for the SLC.
Wire Requirements Distance in Feet (meters) 10,000 feet (3,048 m) 8,000 feet (2,438 m) Twisted-pair, shielded 4,875 feet (1,486 m) Wire Size 12 AWG (3.1 mm2) 14 AWG (2.0 mm2) 16 AWG (1.3 mm2) Wire Type Belden 9583, Genesis 4410, Signal 98230, WPW D999 Belden 9581, Genesis 4408, Signal 98430, WPW D995 Belden 9575, Genesis 4406, & 4606, Signal 98630, WPW D991 Belden 9574, Genesis 4402 & 4602, Signal 98300, WPW D975
3,225 feet (983 m)
18 AWG (0.75 mm2)
MS-9200 = 1,000 feet (305 m) Untwisted, unshielded wire, inside conduit or not in conduit MS-9600, MS-9600LS(C) & MS-9600UDLS = 3,000 feet (914 m) MS-9200UD & MS-9200UDLS = 3,000 feet (914 m) MS-9050UD = 3,000 feet (914 m)
12 to 18 AWG
Table 2.1 SLC Wiring Requirements in CLIP Mode
2.1.2 LiteSpeed Mode

The MS-9200UDLS, MS-9600LS, and MS-9600UDLS SLC can be programmed to operate in LiteSpeed mode for a quicker device response time. While shielded wire is not required, it is recommended that all SLC wiring be twisted-pair to minimize the effects of electrical interference. Use the following table to determine the specific wiring requirements for the SLC.
Wire Requirements Distance in Feet (meters) 10,000 feet (3,048 m) 8,000 feet (2,438 m) Twisted-pair, unshielded 4,875 feet (1,486 m) 3,225 feet (983 m) Wire Size 12 AWG (3.1 mm2) 14 AWG (2.0 mm2) 16 AWG (1.3 mm2) 18 AWG (0.75 mm2) Wire Type Belden 5020UL & 6020UL, Genesis WG-4315 & WG-4515 Belden 5120UL & 6120UL, Genesis WG-4313 & WG-4513 Belden 5220UL & 6220UL, Genesis WG-4311 & WG-4511 Belden 5320UL & 6320UL, Genesis WG-4306 & WG-4506
Table 2.2 SLC Wiring Requirements in LiteSpeed Mode
14
Measuring Resistance & Length
Wiring Requirements
2.2 Measuring Resistance & Length

2.2.1 Two-Wire SLC - Style 4 (Class B)
Loop Resistance
T-tapping of the SLC wiring is permitted for 2-wire Style 4 configurations. The total DC resistance from the control panel to each branch end cannot exceed 40 ohms. Measure DC resistance as detailed and shown below: 1. 2. With power removed, short the termination point of one branch at a time and measure the DC resistance from the beginning of the SLC to the end of that particular branch. Repeat this procedure for all remaining branches in the SLC.
Short Point
Branch
Figure 2.1 Measuring DC Resistance of a Two-Wire SLC
Total Wire Length

The total wire length of all combined branches of one SLC cannot exceed the limits set forth in each systems instruction manual. Determine the total length in each SLC by summing the wire lengths of all branches of one SLC. In the following figure, the total length of the SLC is determined by adding the lengths of Branch A plus Branch B plus Branch C.
Branch A Branch B Branch C
SLC-meas1.wmf
SLC Out
SLC Terminal Block
Figure 2.2 Measuring the Total Wire Length - Two-Wire SLC
SLC-meas2.wmf
15
Wiring Requirements
Measuring Resistance & Length
2.2.2 Four-Wire SLC Style 6 & 7 (Class A)

Loop Resistance
The total DC resistance of the SLC pair cannot exceed 40 ohms. Measure DC resistance as detailed and shown below. 1. 2. 3. Disconnect the SLC channel B (Out) and SLC channel A (Return) at the control panel. Short the two leads of SLC channel A (Return). Measure the resistance across the SLC channel B (Out) leads.
SLC Out Short Point SLC Return

SLC-meas3.wmf SLC-meas4.wmf
Figure 2.3 Measuring DC Resistance of a Four-Wire SLC
Total Wire Length

The total wire length in a four-wire SLC cannot exceed the limits set forth in each systems instruction manual. The figure below identifies the output and return loops from SLC terminal on the control panel:
SLC channel B (output loop)
SLC channel A (return loop)
SLC Terminal Block
B+ B A A+
Figure 2.4 Measuring the Wire Length Four-Wire SLC
16
Shield Wire Termination
Wiring Requirements
2.3 Shield Wire Termination

The drawing below shows the method of proper termination of the shield. Connect the metal conduit to the cabinet by using the proper connector. Feed the shielded wire through the conduit, into the control box. The shield drain wire must be connected to the shield terminal on the SLC terminal block.
NOTE: Use of good wiring practice consistent with local electrical codes is expected.
CAUTION: DO NOT LET THE SHIELD DRAIN WIRE OR THE SHIELD FOIL TOUCH THE SYSTEM CABINET OR BE CONNECTED TO EARTH GROUND AT ANY POINT.
MS-9600 MS-9600LS MS-9600UDLS MS-9200UD MS-9200UDLS MS-9050UD Shield Drain Wire Cabinet Shield Foil
MS-9200
Conduit
Figure 2.5 Shield Termination
17
SLC-shieldterm.wmf
Wiring Requirements
Control Panel Terminal Blocks
2.4 Control Panel Terminal Blocks

The terminal blocks on the control panel circuit board that concern the SLC circuit are described below. For more information on this subject refer to the control panels Instruction Manual.
2.4.1 MS-9200
TB4 provides three types of 24 VDC power; Unregulated, Nonresettable and Resettable. TB6 provides connections for the SLC wiring. 198 addresses are available per loop (99 detectors and 99 modules).
Unregulated Power Nonresettable Power Resettable Power
SHIELD
Connections for wire shield

SLC-9200tb.wmf
SLC SLC
TB4
TB6
SLC Return
SLC Out
Figure 2.6 MS-9200 Terminal Blocks
2.4.2 MS-9600, MS-9600LS, & MS-9600UDLS

TB3 provides two types of 24 VDC power; Nonresettable and Resettable. TB8 provides connections for the SLC wiring. 198 addresses are available per loop (99 detectors and 99 modules) while operating in CLIP mode. 318 addresses are available per loop (159 detectors and 159 modules) while operating in LiteSpeed mode.
Resettable Power Nonresettable Power Connections for wire shield
SLC SLC SLC SLC SHIELD
TB3
TB8
SLC Return SLC Out
Figure 2.7 MS-9600 Series Terminal Blocks
18
SLC-9600tb.wmf
Wiring Requirements
2.4.3 MS-9200UDLS (Software Version 3.0)

TB1 provides two types of 24 VDC power; Nonresettable and Resettable, jumper selectable by JP4 and JP6. TB10 provides connections for the SLC wiring. 198 addresses are available per loop (99 detectors and 99 modules).
Nonresettable Power- jumper selectable by JP4 Resettable Powerjumper selectable by JP6
SLC

SLC-9200udtb.wmf
TB1
TB10
SLC Return SLC Out
Figure 2.8 MS-9200UDLS (Rev 3) Terminal Blocks
2.4.4 MS-9200UD & MS-9200UDLS (Versions 1 and 2)

TB1 provides two types of 24 VDC power; Nonresettable and Resettable. TB10 provides connections for the SLC wiring. 198 addresses are available per loop (99 detectors and 99 modules).
Nonresettable Power Resettable Power Connections for wire shield
SLC-9200udtb.wmf
SLC
TB1
TB10
SLC Return SLC Out
Figure 2.9 MS-9200UD & MS-9200UDLS (Rev 1 & 2) Terminal Blocks
19
Wiring Requirements
2.4.5 MS-9050UD
24 VDC power may be supplied by a remote power supply such as the Fire-Lite FCPS-24FS6/8. TB2 provides connections for the SLC wiring. 50 addresses are available (any combination of detectors and modules).

SLC-9050udtb.wmf
SLC Return SLC Out
Figure 2.10 MS-9050UD Terminal Block
20
Section 3: SLC Circuits without Isolators

3.1 Overview
This chapter concerns itself with the two styles of circuits that do not require isolation devices: NFPA Style 4 NFPA Style 6
3.2 NFPA Style 4 SLC

NFPA Style 4 requirements can be met by using the diagram below. T-tapping of the SLC wiring is allowed for Style 4 configuration.
Two-wire Addressable Detector
Addressable Module
T-tapped Circuits
B+ B Control Panel SLC

SLC-style4.wmf
Figure 3.1 Basic NFPA Style 4 SLC
21
SLC Circuits without Isolators
NFPA Style 6 SLC
3.3 NFPA Style 6 SLC

NFPA Style 6 requirements can be met by using the diagram below. T-tapping of the SLC wiring is NOT allowed for Style 6 configuration.
SLC Out
Addressable Module SLC Return
B+ B A A+
Control Panel SLC
Figure 3.2 Basic NFPA Style 6 SLC
22
SLC-style6.cdrwmf
Section 4: SLC Circuits with Isolators

4.1 Fault Isolator Devices
There are two isolator devices used to protect critical elements of the SLC from faults on other SLC branches or segments. Fault Isolator Module I300 Isolator Detector Base B224BI
A Fault Isolator Module on both sides of a device, or the combination of Isolator Base and Isolator Module is required to comply with NFPA Style 7 requirements.
CAUTION: MAXIMUM ADRESSABLE DEVICES If relay or sounder bases are not used, a maximum of 25 addressable devices can be connected between Isolator Modules and/or Bases. When relay or sounder bases are used, the maximum number of addressable devices that can be connected between Isolators is reduced to seven. Isolator modules will not function properly when these limits are exceeded. When more than 100 Isolator Modules are connected to an SLC loop, the address capacity of the loop is reduced by two (2) addresses for every isolator device in excess of 100.
4.1.1 Isolating an SLC Branch

The module continuously monitors the circuit connected to terminals 3() and 4(+). Upon powerup, an integral relay is latched on. The module periodically pulses the coil of this relay. A short circuit on the SLC resets the relay. The module detects the short and disconnects the faulted SLC branch or segment by opening the positive side of the SLC (terminal 4). This isolates the faulty branch from the remainder of the loop preventing a communication problem with all other addressable devices on the remaining branches (labeled Continuation of the SLC in the figure below). During a fault condition, the control panel registers a trouble condition for each addressable device which is isolated on the SLC segment or branch. Once the fault is removed, the module automatically reapplies power to the SLC branch or segment.
4.1.2 Wiring an Isolator Module

The figure below shows typical wiring of an Isolator Module:
Continuation of the SLC
IN (-) IN (+) OUT (-) OUT (+)

SLC-isowire2.wmf
SLC Isolated branch of the SLC
Figure 4.1 Wiring an I300 Module

SLC Circuits with Isolators
NFPA Style 4 SLC Using Isolator Modules
4.2 NFPA Style 4 SLC Using Isolator Modules

A variation of a Style 4 operation using isolator modules to protect each branch of the SLC is shown below. Refer to Figure 4.1 for I300 wiring and to Section 4.1 for limitations.
Isolator Module Isolated Branch Two-wire Addressable Detector
Isolator Module Isolated Branch
Addressable Pull Station Isolator Module Isolated Branch
B B+
Control Panel SLC
Figure 4.2 NFPA Style 4 SLC Using Isolator Modules
24
SLC-style4iso.wmf

A variation of Style 6 operation using isolator modules to protect a section of the SLC. By flanking each group of devices with an I300 fault isolator module each group is protected from faults that may occur in the other groups. For example, a fault in Section B will not effect Sections A & C. The isolator modules on either side of Section B will open the loop. Section A will still operate from power on the SLC Out side and Section C will operate from the SLC Return side. A combination of isolator modules and isolator bases may be used. T-tapping is NOT allowed within the Style 6 configuration. Isolator modules shall be within 20 feet (6.1 meters) of device and must be enclosed in metal conduit.
Isolator Module
Isolator Module
Section B Two-wire Addressable Detector
Section C
Addressable Pull Station
Section A
Isolator Module
Additional isolator module required when first device in the section is more than 20 feet from the control panel.
Isolator Module
Isolator Module
Isolator Module
SLC Out
SLC Return
Control Panel

SLC-style6iso.wmf

Style 7 operation requires using isolator modules (or a combination of isolator modules and isolator bases) before and after each device. Flanking each device with an isolator provides fault protection to all other devices on the loop. T-tapping is NOT allowed within the Style 7 wiring configuration. When a detector base or pull station is used, install isolator modules on both sides of the device. Connections between isolator modules and the device they isolate must be close-nippled conduit, within 3 feet (91.44 cm).
1 3 1 3
Isolator Module
Isolator Module
Isolator Module
Isolator Module
Two-Wire Addressable Detector
Addressable Pull Station
Isolator Module
Isolator Module
Isolator Module SLC Out SLC Return
Isolator Module
Control Panel
26
SLC-style7iiso.wmf
Section 5: Monitor Modules

5.1 Descriptions
These addressable modules monitor conventional contact-type alarm initiating devices. You can configure module circuits as an NFPA Style B (Class B) or Style D (Class A) Initiating Device Circuits (IDC). There is no limit to the number of contact-type devices installed on a monitor module circuit.
NOTE: For more information on the individual module specifications refer to the Installation Instructions that are provided with these devices.
5.1.1 Addressable Monitor Modules

MMF-300 Monitor Module
This is an addressable module that monitors either a Style B (Class B) or Style D (Class A) circuit of dry-contact input devices. This module is capable of participating in degraded mode where supported by the FACP.
Areas used to record the device address and SLC number.
Figure 5.1 MMF-300 Monitor Module
FMMtpH.wmf
IDC Return IDC Return + IDC Out + IDC Out -
SLC SLC+
Rotary Switches
27
Monitor Modules
Descriptions
MMF-300-10 Monitor Module

This is an addressable monitor module intended to interface between the FACP and up to ten (10) Style B (Class B) or five (5) Style D (Class A) IDCs containing normally open contact devices. This type of module is contained in either a BB-2 or BB-6 cabinet. The BB-2 can accommodate up to 2 modules and the BB-6, which requires the CH-6 chassis, can accommodate up to 6 modules. See the Installation Instructions provided with module for proper installation into a cabinet.
Style Y or Style Z Select Remove shunt for Style Z circuits Disable Address Place shunt in: Disable 1 position to disable highest module address Disable 2 position to disable highest two module addresses SLC Address Set rotary switches to base (first) address of modules
Figure 5.2 MMF-300-10 Monitor Module
28
mmf-300-10.wmf
Descriptions
Monitor Modules
5.1.2 Zone Interface Modules

MMF-302 Module
Similar to the MMF-300, this module is used to monitor a single IDC of UL listed compatible twowire 24 volt conventional smoke detectors. Refer to the Device Compatibility Document.
Figure 5.3 MMF-302 Interface Module
FZMtpH.wmf
24 VDC 24 VDC + IDC Return IDC Return + IDC Out + IDC Out -
SLC SLC+
Rotary Switches
29
Monitor Modules
Descriptions
MMF-302-6 Interface Module

This monitor module is intended to interface between the FACP and a conventional alarm system with up to six (6) Style B (Class B) or three (3) Style D (Class A) IDCs containing normally open contact devices. This type of module is contained in either a BB-2 or BB-6 cabinet. The BB-2 can accommodate up to 2 modules and the BB-6, which requires the CH-6 chassis, can accommodate up to 6 modules. See the Installation Instructions provided with module for proper installation into cabinet.
+ +
T1 T0
T2
+ + + +
T3
+ + + +
T4
T6
T5
A/B SELECT A/B SELECT DISABLE 1 DISABLE 2
5 4 3 2 6 7 8 9 10 11 12 13 1 0 15 14
BASE ADDRESS
J1
SW1
5 4 3 2
BASE ADDRESS +4
10
BASE ADDRESS +0
BASE ADDRESS +1
BASE ADDRESS +2
BASE ADDRESS +3
BASE ADDRESS +5
6 7 8 9
Style Y or Style Z Select Remove shunt for Style Z circuits Disable Address Place shunt in: Disable 1 position to disable highest module address Disable 2 position to disable highest two module addresses SLC Address Set rotary switches to base (first) address of modules
Figure 5.4 MMF-302-6 Interface Module
30
Installation
Monitor Modules
5.1.3 Dual Monitor Module

MDF-300 Module
The MDF-300 is similar to the MMF-300 but provides for two independent 2-wire IDCs at two separate, consecutive addresses.
Rotary Switches Address +1 9 H { 8 H+ SLC SLC+
Base Address
7L+ 6L
Figure 5.5 MDF-300 Dual Monitor Module
5.1.4 Mini Monitor Module

MMF-301 Monitor Module
The MMF-301 is functionally and electrically identical to an MMF-300, but is offered in a smaller package for mounting directly in the electrical box of the Style B (Class B) device being monitored.
Rotary Switches Label Use to record the device address and SLC number.
IDC (+) IDC (-)

FMM-101.wmf
SLC (+) SLC (-)
Figure 5.6 MMF-301 Mini Monitor Module
5.2 Installation
When installing any of these modules DO NOT mix the following services that the IDC provides: Fire alarm service Automatic and manual waterflow alarm service with normally open contact devices Sprinkler supervision with normally open contact devices
fmmtph.wmf
31
Monitor Modules
Installation
5.2.1 Setting an SLC address for a Single Point Module

Each module can be set to one of 159 addresses (01-159) and is factory preset with an address of 00.
NOTE: The MS-9050UD can support addresses 01 - 50. The MS-9200, MS-9200UD, and MS9200UDLS can support module addresses of 01 - 99. The MS-9600, MS-9600LS, and MS9600UDLS can support module addresses 01 - 159. The plastic stop located on the Tens switch must be removed to set addresses above 99.
To set an SLC address, use a screwdriver to adjust the rotary switches on the module to the desired address. The module below is set at 35. When finished, mark the address on the module face in the place provided.
5 4 3 2
6 7 8 910 6789 5 11 4 12 3 13 2 1 0 1514 10 ONES TENS
Modules with Rotary Switches in horizontal position Modules with Rotary Switches in vertical position
Breakaway Tab - Modules come with a raised breakaway tab on the TENS rotary switch. This tab must be removed when the module is on an FACP that uses more than 99 addresses.
Dual monitor modules: On dual monitor modules, only even numbers appear on the ONES rotary switch. The module takes both the selected address and the next-higher address.
Figure 5.7 Setting an SLC Address on a Single Point Module
32
SLC-setadd.cdr,SLC-setaddtpH.wmf, SLCbrktabs.wmf
Installation
Monitor Modules
5.2.2 Setting an SLC address for a Multi-Point Module

The SLC address of a multi-point module is set in the same fashion as a single-point module. In Class B operation, each MMF-300-10, MMF-302-6, CMF-300-6, and CRF-300-6 module is set to a base address. The remaining module points are automatically assigned to the next higher SLC addresses. For example, if the base address of a MMF-300-10 is set to 28, the next module points will be addressed to 29, 30, 31, 32, 33, 34, 35, 36 and 37. In Class A operation, alternate module points are paired together, resulting in a total of five module points. For example, if the base address of a MMF-300-10 is set to 28, then 30, 32, 34 and 36 will be automatically assigned to the remaining module points and 29, 31, 33, 35 and 37 are available for use by other modules.
NOTE: The MS-9050UDNFW-50 can support addresses 01 - 50. The MS-9200, MS-9200UD and MS-9200UDLS can support module addresses of 01 - 99. The MS-9600, MS-9600LS, and MS-9600UDLS can support module addresses 01 - 159 (the plastic stop located on the Tens switch must be removed to set addresses above 99).
To set an SLC address, use a common screwdriver to adjust the rotary switches on the module to the desired address. The module below is set at 28.
5 4 3 2 6 7 8 9 10 11 12 13 10 15 14
TENS
Plastic Stop
Rotary Switches
ONES
Figure 5.8 Setting an SLC Address on a Multi-Point Module
multroty.wmf
5 4 3 2 10 6 7 8 9
33
Monitor Modules
MMF-300 Wiring Diagrams
5.3 MMF-300 Wiring Diagrams

Following are wiring diagrams that depict NFPA Style B (Class B) and D (Class A) Initiating Device Circuits (IDCs) using MMF-300 monitor modules. The Initiating Device Circuit (IDC) is supervised and current-limited to 210 microamperes @ 24 VDC (nominal).
5.3.1 Wiring a NFPA Style B IDC with an MMF-300

Connect the SLC wiring to the module terminals 1 () and 2 (+). Each module takes one address on the SLC. Use the rotary switches on the module to set it to the required SLC address. Refer to Setting an SLC address for a Single Point Module on page 32. The figure below shows typical wiring for a supervised and power-limited NFPA Style B IDC using an MMF-300 module. Refer to the Device Compatibility Document for compatible smoke detectors. See Power Considerations on page 61 for information on supervising 24 VDC power.
From Supply
24 VDC Four-wire Detector Base Manual pull station
24 VDC Power Filtered, Regulated, Resettable
47K ELR (supplied with module) Heat detector MMF-300
To Next IDC or Supervision Device SLC
IDC
Figure 5.9 Typical Style B IDC Wiring with an MMF-300
34
SLC-idcB1tpH.wmf
Monitor Modules
5.3.2 Wiring a NFPA Style D IDC with an MMF-300

Connect the SLC wiring to the module terminals 1 () and 2 (+). Each module takes one address on the SLC. Use the rotary switches on the module to set it to the required SLC address. Refer to Setting an SLC address for a Single Point Module on page 32. The figure below shows typical wiring for a supervised and power-limited NFPA Style D (Class A) IDC using an MMF-300 module. Refer to the Device Compatibility Document for compatible smoke detectors. See Power Considerations on page 61 for information on supervising 24 VDC power.
From Supply
24 VDC Four-wire Detector Base
24 VDC Power Filtered, Regulated, Resettable
Manual pull station To Next IDC or Supervision Device SLC Heat detector MMF-300
IDC
Figure 5.10 Typical Style D IDC Wiring with an MMF-300
SLC-idcD1tpH.wmf
35
Monitor Modules
5.3.3 MMF-300 Wiring for Emergency Alarm System Applications

Connect the SLC wiring to the module terminals 1 () and 2 (+). Each module takes one address on the SLC. Use the rotary switches on the module to set it to the required SLC address. Refer to Setting an SLC address for a Single Point Module on page 32. The figure below shows typical wiring for a supervised and power-limited Emergency Signaling circuit using an MMF-300 module. See Power Considerations on page 61 for information on supervising 24 VDC power. See Section 6, Control Modules for instructions on using control modules as NACs on an SLC. For compatible output devices refer to the Device Compatibility Document #15384.
47K ELR (supplied with module)
SLC
+ -
UL-listed Signaling applicance such as the Fire-Lite FSS-2400E
IDC
SLC-emer.wmf
MMF-300 Module programmed for Tornado, Hazard, or Medical operation. Refer to the control panel installation manual.
Figure 5.11 Emergency Signaling Wiring with an MMF-300
36
MMF-300-10 Wiring Diagrams
Monitor Modules
5.4 MMF-300-10 Wiring Diagrams

Following are wiring diagrams that depict NFPA Style B (Class B) and D (Class A) Initiating Device Circuits (IDCs) using MMF-300-10 monitor modules. The Initiating Device Circuit (IDC) is supervised and current-limited to 1.0 milliampere @ 24 VDC (nominal).
5.4.1 Wiring a NFPA Style B IDC with an MMF-300-10

Connect the SLC wiring to the module terminals T5 as shown below. Use the rotary switches on the module to set the base SLC address. Each module takes ten addresses on the SLC. The remaining module points are automatically assigned to the next nine higher addresses. Refer to Setting an SLC address for a Multi-Point Module on page 33. DO NOT set the lowest address above 150 (41 for the MS-9050UD, 90 for the MS-9200, MS9200UD, and MS-9200UDLS), as the other module points will be assigned to nonexistent addresses. The figure below shows typical wiring for a supervised and power-limited NFPA Style B IDC using an MMF-300-10 module. Refer to the Device Compatibility Document for compatible smoke detectors. See Power Considerations on page 61 for information on supervising 24 VDC power.
24 VDC Power Filtered, Regulated, Resettable 47K ELR (supplied with module) Heat Detector
Manual Pull Station
SLC
MMF-300-10
IDC Out
SLC-idcB4.wmf
Figure 5.12 Typical Style B IDC Wiring with an MMF-300-10
37
Monitor Modules
5.4.2 Wiring a NFPA Style D IDC with an MMF-300-10

Connect the SLC wiring to the module terminals T5 as shown below. Use the rotary switches on the module to set the base SLC address. Each module takes five alternating addresses on the SLC. The remaining module points are automatically assigned to the next four higher addresses. (Example: 28, 30, 32, 34 and 36). Refer to Setting an SLC address for a MultiPoint Module on page 33. DO NOT set the lowest address above 150 (41 for the MS-9050UD, 90 for the MS-9200, MS9200UD, and MS-9200UDLS), as the other module points will be assigned to nonexistent addresses. The figure below shows typical wiring for a supervised and power-limited NFPA Style D (Class A) IDC using an MMF-300-10 module. Refer to the Device Compatibility Document for compatible smoke detectors. See Power Considerations on page 61 for information on supervising 24 VDC power.
24 VDC Power Filtered, Regulated, Resettable Heat Detector
Manual Pull Station
IDC Return
IDC Out
SLC
MMF-300-10
SLC-idcD3.cdwmf
Figure 5.13 Typical Style D IDC Wiring with an MMF-300-10
38
MDF-300 Wiring Diagrams
Monitor Modules
5.5 MDF-300 Wiring Diagrams

Following is a wiring diagrams that depict NFPA Style B (Class B) Initiating Device Circuits (IDCs) using MDF-300 Dual Monitor Modules.
5.5.1 Wiring a NFPA Style B IDC with an MDF-300

Connect the SLC wiring to the module terminals 1 () and 2 (+). Use the rotary switches on the module to set it to the SLC address. Each dual module takes two addresses on the SLC. Circuit L corresponds to the address set on the rotary switches, which will be an even number. Circuit H will automatically respond to the next higher address, which will be an odd number. Use caution to avoid duplicate addressing of modules on the system. Refer to Setting an SLC address for a Single Point Module on page 32. Each IDC (H & L) is power limited to 230 microamperes @ 24 VDC. The figure below shows typical wiring for a supervised and power-limited NFPA Style B IDC using an MDF-300-10 module. Refer to the Device Compatibility Document for compatible smoke detectors. See Power Considerations on page 61 for information on supervising 24 VDC power.
Manual Pull Station 47K ELR Heat Detector
Manual Pull Station 47K ELR MDF-300 SLC
Figure 5.14 Typical Style B IDC Wiring with an MDF-300
SLC-idcB3fdm1tph.wmf
Base Address (IDC Circuit L)
Base +1 Address (IDC Circuit H)
T11 T10 T9 T8 T7 T6
T1 T2 T3 T4 T5
39
Monitor Modules
5.6 MMF-302 Wiring Diagrams

Following are wiring diagrams that concern NFPA Style B (Class B) and D (Class A) Initiating Device Circuits (IDCs) using MMF-302 Zone Interface Modules.
5.6.1 Wiring a NFPA Style B IDC with an MMF-302

Connect the SLC wiring to the module terminals 1 () and 2 (+). Each module takes one address on the SLC. Use the rotary switches on the module to set it to the required SLC address. Refer to Setting an SLC address for a Single Point Module on page 32. The IDC is supervised and power limited to 230 microamperes @ 24 VDC. The figure below shows typical wiring for a supervised and power-limited NFPA Style B IDC using an MMF-302 module. Refer to the Device Compatibility Document for compatible smoke detectors. 24 VDC power must be provided from a UL listed power supply for fire protection use. This power is inherently supervised by the module. See Power Considerations on page 61 for information on 24 VDC power.
Two-wire smoke detectors
24 VDC Resettable power. 90 mA External 24 volt supply required 3.9K ELR (supplied with module)
SLC
MMF-302
Figure 5.15 Typical Style B IDC Wiring with an MMF-302
40
SLC-idcB2tpH.wmf
IDC
Monitor Modules
5.6.2 Wiring a NFPA Style D IDC with an MMF-302

Connect the SLC wiring to the module terminals 1 () and 2 (+). Each module takes one address on the SLC. Use the rotary switches on the module to set it to the required SLC address. Refer to Setting an SLC address for a Single Point Module on page 32. The figure below shows typical wiring for a supervised and power-limited NFPA Style D (Class A) IDC using an MMF-302 module. Refer to the Device Compatibility Document for compatible smoke detectors. 24 VDC power must be provided from a UL listed power supply for fire protection use. This power is inherently supervised by the module. See Power Considerations on page 61 for information on 24 VDC power.
24 VDC Resettable power. 90 mA External 24 volt supply required SLC MMF-302
IDC
SLC-idcD2tpH.wmf
3.9K ELR (supplied with module)
Figure 5.16 Typical Style D IDC Wiring with an MMF-302
41
Monitor Modules
5.7 MMF-302-6 Wiring Diagrams

Following are wiring diagrams that concern NFPA Style B (Class B) and D (Class A) Initiating Device Circuits (IDCs) using MMF-302-6 monitor modules.
5.7.1 Wiring a NFPA Style B IDC with an MMF-302-6

Connect the SLC wiring to the module terminals T0 as shown below. Use the rotary switches on the module to set the base SLC address. Each module takes six addresses on the SLC. The remaining module points are automatically assigned to the next five higher addresses. Refer to Setting an SLC address for a Multi-Point Module on page 33. DO NOT set the lowest address above 150 (41 for the MS-9050UD, 90 for the MS-9200, MS9200UD, and MS-9200UDLS), as the other module points will be assigned to nonexistent addresses. The figure below shows typical wiring for a supervised and power-limited NFPA Style B IDC using an MMF-302-6 module. Refer to the Device Compatibility Document for compatible smoke detectors. 24 VDC power must be provided from a UL listed power supply for fire protection use. This power is inherently supervised by the module. See Power Considerations on page 61 for information on 24 VDC power.
3.9K ELR (supplied with module)
24 VDC resettable power
IDC Out SLC MMF-302-6

SLC-idcB5.wmf
Figure 5.17 Typical Style B IDC Wiring with an MMF-302-6
42
Monitor Modules
5.7.2 Wiring a NFPA Style D IDC with an MMF-302-6

Connect the SLC wiring to the module terminals T0 as shown below. Use the rotary switches on the module to set it to the SLC addresses. Each module takes three alternating addresses on the SLC. The remaining module points are automatically assigned to the next two higher addresses. (Example: 28, 30 and 32). Refer to Setting an SLC address for a MultiPoint Module on page 33. DO NOT set the lowest address above 150 (41 for the MS-9050UD, 90 for the MS-9200, MS9200UD, and MS-9200UDLS), as the other module points will be assigned to nonexistent addresses. The figure below shows typical wiring for a supervised and power-limited NFPA Style D (Class A) IDC using an MMF-302-6 module. Refer to the Device Compatibility Document for compatible smoke detectors. 24 VDC power must be provided from a UL listed power supply for fire protection use. This power is inherently supervised by the module. See Power Considerations on page 61 for information on 24 VDC power.
+ + +
SLC
24 VDC resettable power IDC Return IDC Out
MMF-302-6
SLC-idcD4.wmf
+ +
T1 T0
T2
+ + + +
T3
+ + + +
T4
Figure 5.18 Typical Style D IDC Wiring with an MMF-302-6
43
Section 6: Control Modules

When using a Control Module as a Notification Appliance Circuit (NAC), the isolation described in the section titled Section 4, SLC Circuits with Isolators which begins on page 23, is required or Riser Conductors must be installed in accordance with the survivability from attack by fire requirements in National Fire Alarm Code, NFPA 72.
6.1 Description
The CMF-300 and CMF-300-6 modules are addressable modules that can be used for monitoring and switching 24 VDC Notification Appliance Circuit (NAC) power for NFPA Style Y (Class B) and NFPA Style Z (Class A) circuits. Ratings for the relay contacts on the module are:
Load Description Resistive Resistive Resistive Resistive Inductive (L/R = 5ms) Inductive (L/R = 2ms) Inductive (PF = 0.35) Application Non-Coded Coded Non-Coded Non-Coded Coded Coded Non-Coded Maximum Voltage 30 VDC 30 VDC 110 VDC 125 VAC (CMF-300) 70.7 VAC (CMF-300-6) 30 VDC 30 VDC 125 VAC (CMF-300) 70.7 VAC (CMF-300-6) Current Rating 3.0 A 2.0 A 0.9 A 0.9 A 0.5 A 1.0 A 0.5 A
NOTE: For more information on module specifications, refer to the Installation Instructions provided with these devices.
6.2 CMF-300 Installation

6.2.1 Setting an SLC address for a CMF-300 Module
Each module is factory preset with an address of 00. To set an SLC address refer to Setting an SLC address for a Single Point Module on page 32.
6.2.2 Wiring a Notification Appliance Circuit (NAC) with a CMF-300

The figure below shows the connections to wire a module for powering a 24 VDC NAC:
24 VDC Nonresettable Power () 24 VDC Nonresettable Power (+) Style Z NAC (+) Style Z NAC () Style Y/Z NAC () Style Y/Z NAC (+) NOTE: Module polarities are shown in alarm condition.
SLC () SLC (+)
Figure 6.1 CMF-300 Wiring Connections

FCMFZMtph.wmf
Wiring a CMF-300 Module
Control Modules
6.3 Wiring a CMF-300 Module

This section contains instructions and diagrams for wiring a Signaling Line Circuit with a CMF-300 as a Notification Appliance Circuit (NAC).
6.3.1 Wiring a Style Y NAC (Two-Wire) with Addressable Control Modules

A supervised and power-limited NFPA Style Y (Class B) NAC using a CMF-300 module. Polarized alarm notification appliances are shown connected to the module in a two-wire configuration. Refer to the Device Compatibility Document for compatible notification appliances and relays. See Power Considerations on page 61 for information on monitoring 24 VDC power. Each module can control 2 amps of resistive load (on electronic devices) or 1 amp of inductive load (on mechanical bells and horns). 24 VDC power must be provided from a UL listed power supply for fire protection use. A power supervision relay is required only on the last module of the power run. Do not T-tap or branch a Style Y circuit. Terminate the circuit across the last device using an End-of-Line Resistor 47K, 1/2-watt, P/N SSD A2143-00 (ELR-47K in Canada). Do not loop wiring under the screw terminals of any notification appliance. To maintain supervision, break the wire run at each device.
SLC 24 VDC Nonresettable power CMF-300 NOTE: A power supervision relay is required only on the last module of the power run.
ELR 47K, 1/2-watt
24 VDC Notification Appliances
NAC Note: Module polarities are shown in alarm condition
Figure 6.2 NFPA Style Y Notification Appliance Circuit
45
SLC-nacY.wmf
Control Modules
CMF-300-6 Installation
6.3.2 Wiring a Style Z NAC (Four-Wire) with Addressable Control Modules

A supervised and power-limited NFPA Style Z (Class A) NAC using a CMF-300 module. Polarized alarm notification appliances are shown connected to the module in a four-wire configuration.
NOTE: Refer to the Device Compatibility Document for compatible notification appliances and relays.
See Power Considerations on page 61 for information on monitoring 24 VDC power. Each module can control 2 amps of resistive load (on electronic devices) or 1 amp of inductive load (on mechanical bells and horns). 24 VDC power must be provided from a UL listed power supply for fire protection use. A power supervision relay is required only on the last module of the power run. Do not T-tap or branch a Style Z circuit. Do not loop wiring under the screw terminals of any notification appliance. To maintain supervision, break the wire run at each device.
NOTE: A power supervision relay is required only on the last module of the power. 24 VDC Nonresettable power 24 VDC notification appliances CMF-300 SLC
NAC Return NAC Out
Note: Module polarities are shown in alarm condition.
Figure 6.3 NFPA Style Z Notification Appliance Circuit
6.4 CMF-300-6 Installation

6.4.1 Cabinet Installation
This type of module is contained in either a BB-2 or BB-6 cabinet. The BB-2 can accommodate up to 2 modules and the BB-6, which requires the CH-6 chassis, can accommodate up to 6 modules. See the Installation Instructions provided with module for proper installation into cabinet.
6.4.2 Setting an SLC address for an CMF-300-6 Module

In Style Y operation each CMF-300-6 module can be set to one of 154 base addresses (01-154). The remaining module points are automatically assigned to the next five higher SLC addresses. For example, if the base address is set to 28, the next five module points will be addressed to 29, 30, 31, 32 and 33.
SLC-nacZtpH.wmf
Control Modules
In Style Z operation alternate module points are paired together, resulting in a total of three module points. For example, if the base address is set to 28, then 30 and 32 will be automatically assigned to the remaining module points and 29, 31 and 33 are available to be used for other modules on the SLC. DO NOT set the lowest address above 154 (45 for the MS-9050UD, 94 for the MS-9200, MS9200UD, and MS-9200UDLS), as the other module points will be assigned to nonexistent addresses.
NOTE: The MS-9050UD can support addresses 01 - 50. The MS-9200, MS-9200UD, and MS9200UDLS can support module addresses of 01 - 99. The MS-9600, MS-9600LS, MS-9600LSC, and MS-9600UDLS can support module addresses 01 - 159.
To set an SLC address, use a common screwdriver to adjust the rotary switches on the module to the desired address. See Figure 6.4 on page 48.
NOTE: For use with the MS-9600, MS-9600LS, MS-9600LSC, and MS-9600UDLS, remove the stop on the upper rotary switch.
6.4.3 Setting NACs as Style Y or Style Z

To use this module for Style Y (Class B) operation ascertain that a small shunt is installed on the A/B SELECT set of pins. (As shipped). To use this module for Style Z (Class A) operation remove the small shunt from the A/B SELECT set of pins. See drawing below and Figure 6.4 on page 48.
6.4.4 Disabling Unused Module Addresses

A shunt is used, in conjunction with a pin block, to disable a maximum of three (3) unused module addresses. If two module addresses are disabled, the lowest four addresses will be functional, while the highest two will be disabled. For example, if the shunt is placed on DISABLE 2 and the base address is set to 28, the module addresses will be assigned to 28, 29, 30 and 31. In Style Z operation, placing a small shunt on DISABLE 3 will disable all three addresses. Placing it on DISABLE 2 will disable two out of three addresses. To disable addresses, securely place one of the supplied small shunts onto the desired set of pins. See drawing and Figure 6.4 on page 48.
J1
6.4.5 Short Circuit Protection

Protection is disabled for each module address when there is a large shunt installed on the corresponding pins of the pin block (as shipped, all six addresses are disabled). When enabled, the module will not switch power supply if a short circuit condition exists on a NAC. To enable Short Circuit Protection for an address, remove the large shunt from the corresponding pins of the pin block. See Figure 6.4 on page 48. Place unused shunts on single pin to store on board for future use.
SLC-disable1.wmf
A/B SELECT DISABLE 1 DISABLE 2 DISABLE 3
47
Control Modules
6.4.6 Features Not Supported

The Synchronization and Power Supply Monitoring features are not supported at this time.
6.4.7 Circuit Board Information

Synchronization Generator Not Supported. DO NOT remove shunts. Power Supply Monitors Not Supported. DO NOT remove shunts.
#1
#2
#3
#4
#5
#6
Disable Address Place shunt onto required pins. Select Style Y (Class B) or Style Z (Class A) Remove shunt for Style Z (Class A).
SLC Address Set rotary switches to address required. Short Circuit Protection - Remove shunt from the corresponding pins to enable. Shunt #1 for first address, #2 for second address, etc.
Figure 6.4 CMF-300-6 Control Module Settings
48
CMF-300-6.wmf
Status Indicators Green LEDs are controlled by FACP to indicate status of each module address.
Wiring a CMF-300-6 Module
Control Modules
6.5 Wiring a CMF-300-6 Module

This section contains basic instructions and diagrams for wiring a Signaling Line Circuit with a CMF-300-6 as a Notification Appliance Circuit (NAC). For more detailed information on wiring a CMF-300-6 Control Module refer to the Installation Instructions provided with the module. Included in these instructions are wiring diagrams concerning a single power supply being shared by multiple NACs and audio NAC configurations.
6.5.1 Wiring a Style Y NAC (Two-Wire)

A supervised and power-limited NFPA Style Y (Class B) NAC with a single power supply dedicated to a single NAC using a CMF-300-6 module. Polarized alarm notification appliances are shown connected to the module in a two-wire configuration.
See Power Considerations on page 61 for information on monitoring 24 VDC power. Each module can control 2 amps of resistive load (on electronic devices) or 1 amp of inductive load (on mechanical bells and horns). 24 VDC power must be provided from a UL listed power supply for fire protection use. A power supervision relay is required only on the last module of the power run. Do not T-tap or branch a Style Y circuit. Terminate the circuit across the last device using an End-of-Line Resistor 47K, 1/2-watt, P/N SSD A2143-00 (ELR-47K in Canada). Do not loop wiring under the screw terminals of any notification appliance. To maintain supervision, break the wire run at each device.
Power Supervision Relay (EOLR-1) 24 VDC nonresettable power
ELR 47K, 1/2-watt
24 VDC notification appliances
NAC Out SLC Relay Connector Assembly
CMF-300-6
T0 +0 + +
+
T1
+1
T2
+2
T3
+3
T4
+4
+5
T10
T11
T12
T13
T14
T15 T16
Figure 6.5 NFPA Style Y Notification Appliance Circuit
SLC-nacY2.wmf
T5
49
Control Modules
Wiring a CMF-300-6 Module
6.5.2 Wiring a Style Z NAC (Four-Wire)

A supervised and power-limited NFPA Style Z (Class A) NAC with a single power supply dedicated to a single NAC using a CMF-300-6 module. Polarized alarm notification appliances are shown connected to the module in a four-wire configuration.
See Power Considerations on page 61 for information on monitoring 24 VDC power. Each module can control 2 amps of resistive load (on electronic devices) or 1 amp of inductive load (on mechanical bells and horns). 24 VDC power must be provided from a UL listed power supply for fire protection use. A power supervision relay is required only on the last module of the power run. Do not T-tap or branch a Style Z circuit. Do not loop wiring under the screw terminals of any notification appliance. To maintain supervision, break the wire run at each device.
Power Supervision Relay (EOLR-1) 24 VDC nonresettable power
24 VDC notification appliances
NAC Out SLC NAC Return
CMF-300-6
Power Supply Jumper Relay Connector Assembly
Figure 6.6 NFPA Style Z Notification Appliance Circuit
50
SLC-nacZ3.cwmf
Section 7: Relay Modules

7.1 Description
The CRF-300 and the CRF-300-6 modules are addressable modules that provides Form-C relay contacts. Ratings for the relay contacts on the module are:
Load Description Resistive Resistive Resistive Resistive Inductive (L/R = 5ms) Inductive (L/R = 2ms) Inductive (PF = 0.35) Inductive (PF = 0.35) Application Non-Coded Coded Non-Coded Non-Coded Coded Coded Non-Coded Non-Coded Maximum Voltage 30 VDC 30 VDC 110 VDC 125 VAC 30 VDC 30 VDC 70.7 VAC 125 VAC Current Rating 3.0 A 2.0 A 0.9 A 0.9 A 0.5 A 1.0 A 0.7 A 0.5 A
NOTE: For more information on the module specifications refer to the Installation Instructions provided with these devices.
7.2 CRF-300 Installation & Wiring

7.2.1 Setting an SLC address for a CRF-300 Module
Each module is factory preset with an address of 00. To set an SLC address, refer to Setting an SLC address for a Single Point Module on page 32.
7.2.2 Wiring a CRF-300 Module (Form-C Relay)

The figure below shows a CRF-300 module wired to the Control Panel:
SLC CRF-300
C NC NO C NC
NO
Figure 7.1 CRF-300 Wiring Connections

SLC-frmCtpH.wmf
Relay Modules
CRF-300-6 Circuit Board Information
7.3 CRF-300-6 Circuit Board Information
T102
+ +
5 4 3 2
NONE ONE TWO THREE
6 7 8 9 10 11 12 13 1 0 1514
BASE ADDRESS
ADDRESS DISABLE
Disable Address Place shunt onto required pins.
J1
SW1
5 4 3 2 1 0 6 7 8 9
Status Indicators Green LEDs are controlled by FACP to indicate status of each module address. SLC Address Set rotary switches to address required.
Figure 7.2 CRF-300-6 Control Relay Module
7.4 CRF-300-6 Installation & Wiring

7.4.1 Cabinet Installation
This type of module is contained in either a BB-2 or BB-6 cabinet. The BB-2 can accommodate up to 2 modules and the BB-6, which requires the CH-6 chassis, can accommodate up to 6 modules. See the Installation Instructions provided with module for proper installation into cabinet.
52
CRF-300-6 Installation & Wiring
Relay Modules
7.4.2 Setting an SLC address for a CRF-300-6 Module

Each CRF-300-6 module can be set to one of 154 base addresses (01-154). The remaining module points are automatically assigned to the next five higher SLC addresses. For example, if the base address is set to 28, the next five module points will be addressed to 29, 30, 31, 32 and 33. DO NOT set the lowest address above 154 (45 for the MS-9050UD, 94 for the MS-9200, MS9200UD, and MS-9200UDLS), as the other module points will be assigned to nonexistent addresses.
NOTE: The MS-9050UD can support addresses 01 - 50. The MS-9200, MS-9200UD, and MS9200UDLS can support module addresses of 01 - 99. The MS-9600, MS-9600LS, and MS9600UDLS can support module addresses 01 - 159. To set an SLC address, use a common screwdriver to adjust the rotary switches on the module to the desired address. See Figure 6.4 on page 48. For use with an MS-9600, MS-9600LS, MS-9600LSC, and MS-9600UDLS, remove the stop on the upper rotary switch.
7.4.3 Disabling Unused Module Addresses

A shunt is provided on the circuit board to disable a maximum of three (3) unused module addresses. If two module addresses are disabled, the lowest four addresses will be functional, while the highest two will be disabled. For example, if the shunt is placed on TWO and the base address is set to 28, the module addresses will be assigned to 28, 29, 30 and 31. To disable addresses, remove the shunt from its storage location and securely place it onto the desired set of pins. See illustration.
J1
Shunt Storage Location
7.4.4 Wiring a CRF-300-6 Module (Form-C Relay)

The figure below shows a CRF-300-6 module wired to the Control Panel.
SLC Out SLC In
Relay Connections
CRF-300-6
+ +
SLC-fmC1.wmf
Figure 7.3 CRF-300-6 Wiring Connections
SLC-disable2.wmf
+
53
Section 8: Multiple Input/Output Modules

8.1 Description
The CDRM-300 is an addressable module that functions as two individual relay control modules (two isolated sets of Form-C relay contacts) and two Class B monitor modules. Ratings for the relay contacts on the module are:
Load Description Inductive (PF = 0.35) Resistive Resistive Inductive (L/R = 20ms) Inductive (PF = 0.35) Resistive Inductive (PF = 0.75) Inductive (PF = 0.35) Application Non-Coded Non-Coded Coded Non-Coded Non-Coded Non-Coded Non-Coded Non-Coded Maximum Voltage 25 VAC 30 VDC 30 VDC 30 VDC 70.7 VAC 125 VDC 125 VAC 125 VAC Current Rating 2.0 A 3.0 A 2.0 A 0.46 A 0.7 A 0.9 A 0.5 A 0.3 A
NOTE: For more information on the module specifications refer to the Installation Instructions provided with these devices.
8.2 CDRM-300 Installation & Wiring

8.2.1 Setting an SLC address for a CDRM-300 Module
Each module is factory preset with an address of 00. To set an SLC address, use a screwdriver to adjust the rotary switches on the module to the desired address. Each module can use up to four (4) addresses. The base address selected via the rotary address switches will be assigned to relay output #1 from 00 to 156. The module will automatically assign the next three addresses as appropriate to monitored input #1, relay output #2, and monitored input #2.
54
CDRM-300 Installation & Wiring
Multiple Input/Output Modules
8.2.2 Wiring a CDRM-300 Module (Form-C Relay)

The figure below shows a CDRM-300 module wired to the Control Panel
SLC CDRM-300
NC C NO NC C NO
IDC 1 (+) IDC 1 (-) IDC 2 (+) IDC 2 (-)
Normally Closed Common Normally Open Normally Closed Common Normally Open
Figure 8.1 CDRM-300 Wiring Connections
fdrm-1.wmf
55
Section 9: Intelligent Detector Bases

9.1 Description
The following bases provide connection between the SLC and these detector heads: AD350 and AD355 Multicriteria Photoelectric Smoke Detector CP350 and CP355 Ionization Smoke Detector H350, H350R, H355, H355R and H355HT Thermal Detector SD350, SD350T, SD355 and SD355T Photoelectric Smoke Detector
The B501 and B210LP bases are standard plug-in detector bases. The B501BH, B501BHT, B501BH-2, B501BHT-2, and B200SR Sounder Detector Bases include a horn that will sound when the sensors visible LEDs are latched on for approximately 10 seconds. On the MS-9200 Control Panel, the sounder will activate when the sensors visible LEDs are latched on for approximately 10 seconds (Alarm Verification does not delay sounder). If the MS-9600, MS-9600LS, MS-9600UDLS, MS-9200UD, MS-9200UDLS, or MS-9050UD Control Panel is set with Alarm Verification ON, the sounder will activate at the end of the verification cycle, providing an alarm is verified, approximately 10 seconds after the sensors LEDs are latched on. If Alarm Verification is OFF, the sounder will activate when the sensors visible LEDs are latched on for approximately 10 seconds. The B224RB Relay Detector Base includes Form-C latching relay contacts for the control of an auxiliary function. The relay operates 12 seconds (nominally) after activation of the sensor head remote annunciator output. The B224BI Isolator Detector Base prevents an entire communications loop from being disabled when a short circuit occurs.
NOTE: For more information, refer to the Installation Instructions provided with these devices.
9.2 Installation and Wiring

9.2.1 Setting the Detector Address
Each intelligent detector is factory preset with an address of 00. To set an SLC address, use a common screwdriver to adjust the rotary switches on the detector to the desired address (see Setting an SLC address for a Single Point Module on page 32). When finished, mark the address in the place provided on the base and the detector.
56
Installation and Wiring
Intelligent Detector Bases
9.2.2 Wiring a Detector Base

Typical wiring of a detector base (B501 shown) connected to an SLC is shown in the figure below. An optional RA100Z/RA400Z Remote LED Annunciator is shown connected to the detector.
From Control Panel SLC
To Next Device on SLC
Figure 9.1 Wiring a B210LP or B501 Detector Base
NOTE: The B210LP base wiring is identical to the B501. B501 is the flangeless model.
SLC-B5012wire.wmf
RA100Z / RA400Z Remote LED Annunciator (Optional)
57
9.2.3 Wiring an Isolator Base

The B224BI Isolator Base will isolate its detector from short circuits that occur on the SLC connected at terminals 2 and 3. It will not isolate its installed detector from short circuits that occur on the SLC connected at terminals 1 and 2. In Style 7 applications, the loss of a single detector during a short circuit is not acceptable, and an isolator module must be installed as shown in the figure below.
SLC Out Note: The grid pattern on the redesigned B224BI mounting plate has been removed for illustration purposes only.
+
+
SLC In
Conduit
slc-224bi2wire.wmf
I300 Isolator Module
Figure 9.2 Wiring of a B224BI Isolator Base Mounting Plate
9.2.4 Wiring a Relay Base

Figure 9.3 shows typical wiring of a B224RB plug-in relay detector base connected to an SLC.
Note: The grid pattern on the redesigned B224RB mounting plate has been removed for illustration purposes only.
To next device on SLC
+-
Normally Closed Common Normally Open
SLC
+-
Figure 9.3 Wiring of a B224RB Relay Base Mounting Plate
58
slc-b224rb2wire.wmf
9.2.5 Wiring a Sounder Base

Figure 9.4 shows typical wiring of the B200SR Sounder Base.
Note: The grid pattern on the B200SR has been removed for illustration purposes only.
+-
Optional Sounder Interconnect
SLC
+-
UL-Listed 24V Power Supply
+ -
Figure 9.4 Wiring of a B200SR Sounder Base
NOTE: For more detailed wiring on the sounder base, refer to the devices installation instructions.
slc-b200srwire.wmf
59
Section 10: Addressable Manual Pull Station

10.1 Description
The BG-12LX is an addressable manual pull station with a key-lock reset feature.
NOTE: For more information refer to the Installation Instructions provided with this device.
10.2 Installation
10.2.1 Setting an SLC address
Each unit is factory preset with an address of 00. To set an SLC address refer to Setting an SLC address for a Single Point Module on page 32.
10.2.2 Wiring a Manual Pull Station

Figure 10.1 shows typical wiring for a BG-12LX Manual Pull Station to an SLC:
+
SLC
US PAT 4440991
Figure 10.1 Wiring of a BG-12LX Pull Station to an SLC
SLC-bg12lx2.wmf
60
Appendix A: Power Considerations

A.1 Supplying Power to 24 VDC Detectors and NACs
A.1.1 Resistance and Size
To determine the minimum resistance that can be tolerated in supplying power to 24 VDC 4-wire devices and NACs, use the calculation below. Use this resistance to select the proper gauge wire for the power run from the manufacturers specifications for the desired wire. For Four-Wire Detectors:
(Vms - Vom) Rmax = (N)(Is) + (Na)(Ia) + (Ir)
For NACs:
(Vms - Vom) Rmax = (Nb)(Ib)
Where: Rmax = maximum resistance of the 24 VDC wires Vms = minimum supply voltage Vom = minimum operating voltage of the detector or end-of-line relay, whichever is greater, in volts N = total number of detectors on the 24 VDC supply circuit Is = detector current in standby Na = number of detectors on the 24 VDC power circuit which must function at the same time in alarm Ia = detector current in alarm Ir = end-of-line relay current Nb = number of Notification Appliance Devices Ib = Notification Appliance current when activated
NOTE: This simplified equation assumes that the devices are at the end of a long wire run.
The minimum supply voltages produced by FireLite power supplies are listed below:
FACP MS-9200 MS-9600 MS-9200UD/MS-9200UDLS MS-9050UD Vms 16.0 16.0 19.05 18.75 Power Supply FCPS-24F FCPS-24FS6/FCPS-24FS8 Vms 19.1 19.1
Table A.1 Minimum Supply Voltage
61
Power Considerations
Supervising 24 VDC Power
A.2 Supervising 24 VDC Power

Power used to supply 24 VDC detectors, notification appliances (using the CMF-300), and two wire detectors (using the MMF-302) can be supervised with a power supervision relay. This relay, energized by the 24 VDC power itself, is installed at the end of each respective power run and wired in-line with the supervised circuit of any intelligent module. 24 VDC power must be provided from a UL-listed power supply for fire protection use. When power is removed from the relay, the normally closed contacts open the supervised circuit, generating a trouble condition. Therefore, the relay needs to be installed at the end of the supervised circuit, so it will not disrupt the operating capability of all the devices on that circuit. The relay can be installed in-line with any leg (+ or ) of the supervised NAC circuit, either a Style B (Class B) or a Style D (Class A) circuit. The drawing below illustrates this concept.
24 VDC Power from Control Panel or Power Supply Last device on the SLC loop Power Supervision Relay (EOLR-1)
ELR 47K
Supervised NAC
Figure A.1 Supervised 24 VDC Circuit
62
SLC-psrtpH.cdr
Supervising 24 VDC Power
Power Considerations
An alternate method is shown below.

24 VDC Power from Control Panel or Power Supply CMF-300 ELR 47K Power Supervision Relay (EOLR-1)
ELR 47K
Supervised NAC
MMF-300
Figure A.2 Alternate: 2-Address Method of Supervising a 24 VDC Circuit
SLC-psr-2addresstpH.wmf
63
Appendix B: Surge Suppression

B.1 Introduction
NOTE: Surge protection is not required in Canadian applications.
There are three (3) primary surge protectors that are approved for use with the MS-9200, MS9200UD, MS-9200UDLS, MS-9600, MS-9600LS, MS-9600UDLS, and MS-9050UD. DTK-2LVLP-F (727) 812-5000 SLCP-30 Diversified Technology Group, Inc. 1720 Starkey Rd. Largo, FL 33771
EDCO 1805 N.E. 19th Ave. Ocala, FL 34470 (352) 732-3029
PLP-42N Northern Technologies, Inc. 23123 E. Madison Ave. Liberty Lake, WA 99019 (800) 727-9119
NOTE: For detailed information, refer to the Installation Instructions supplied with the unit.
One primary surge protector must be used with each SLC wiring pair whenever SLC wiring runs outside the building. Install primary protection only as shown in this document. Refer to NEC Article 800 and local building code requirements.
Additional primary surge suppressors may be added as required by the NEC. Add these additional suppressors in series with the SLC wiring at the building entry/exit. Wiring connected to the surge suppressor output must remain within the building while wiring connected to the surge suppressor input may be routed outside the building as shown below.
Building #2 Building #1
P P = Primary S = Secondary
P FACP S
Surge Suppressor
Primary devices meet NEC Requirements
Secondary devices meet UL1459 (UL1950)
B.2 Installation
Mounting of the surge suppressor must be inside the FACP enclosure or in a separate enclosure listed for fire protective signaling use. Locate on an available stud and secure with nut. Unit is connected in series with the SLC Loop to protect the Control Panel. Provide a common ground to eliminate the possibility of a differential in ground potentials.
64
SLC-ssbuild1.wmf
Installation
Surge Suppression
B.2.1 Wiring Diagram for MS-9200

DTK-2LVLP-F Connections
2LVLP-F
Optional Four-wire Return Loop Style 6 (Class A)
IN
OUT SLC Terminal Block ABA+ B+ A Shield B Shield
2LVLP-F
SLC Loop IN OUT
PLP-42N Connections
PLP-42N
GRND
L4 L4
OUTPUT
INPUT
L3
L2
L1
L1
L2
L3
PLP-42N
NOTE: Use 12AWG (3.25mm2) to 18AWG (0.75mm2) wire with crimp-on connectors to connect the units ground terminal to equipment ground. Wire length must be minimized to provide best protection.
SLCP-30 Connections
2LCP-30
L1
SLC Loop
IN SLC Loop +
OUT
SLC Terminal Block ABA+ B+ A Shield B Shield
2LCP-30
IN
OUT
SLC-slcp1.wmf
SLC-plpn1.wmf
OUTPUT
INPUT
L3
L2
L1
L2
L3
SLC Terminal Block ABA+ B+ A Shield B Shield
GRND
L4
L4
SLC-lvlp1.wmf
65
Surge Suppression
Installation
B.2.2 Wiring Diagram for MS-9600, MS-9600LS, MS-9600UDLS, MS-9200UD, MS-9200UDLS, and MS-9050UD
DTK-2LVLP-F Connections
2LVLP-F
Optional 4-wire Return Loop Style 6 (Class A)
IN
OUT
2LVLP-F
SLC Terminal Block B+ A+ BAA Shield B Shield
SLC Loop IN OUT
PLP-42N Connections
PLP-42N
GRND
L4
L4
OUTPUT
INPUT
L2
L1
L1
L2
L3
L3
SLC Terminal Block

PLP-42N
OUTPUT
INPUT
L3
L3
+
SLC Loop
NOTE: Use 12AWG (3.25mm2) to 18AWG (0.75mm2) wire with crimp-on connectors to connect the units ground terminal to equipment ground. Wire length must be minimized to provide best protection.
SLCP-30 Connections
2LCP-30
IN SLC Loop +
OUT SLC Terminal Block B+ A+ BAA Shield B Shield
2LCP-30
IN
OUT
66
SLC-slcp4.wmf
SLC-plpn4.wmf
B+ A+ BAA Shield B Shield
GRND
L4
L2
L1
L1
L2
L4
SLC-lvlp4.wmf
Appendix C: Terminal Conversion Charts for New & Legacy Devices

C.1 CRF-300
Common 2 Closed 2 Open 2 Common 1 Closed 1
SLC SLC + Open 1
Common 2 Closed 2 Open 2 Common 1 Closed 1
SLC SLC + Open 1
Legacy Module (V-Type) Legacy Module Terminal Number (V-Type) 1 2 3 4 5 6 7 8 9 N/A N/A
Newer Module (H-Type)
Terminal Function SLC SLC + Unused Normally Open (1) Normally Closed (1) Relay Common (1) Normally Open (2) Normally Closed (2) Relay Common (2) Unused Unused
Newer Module Terminal Number (H-Type) 1 2 3 5 6 7 8 9 10 4 11
Table C.1 CRF-300Terminal Conversions
67
Terminal Conversion Charts for New & Legacy Devices
CMF-300 and MMF-302
C.2 CMF-300 and MMF-302

All module polarities are shown in standby condition, which reflects the labels on the new modules.
AA+ B/A + B/A -
SLC SLC + VDC VDC +
VDC VDC + AA+ B/A + B/A -
SLC SLC +
Legacy Module (V-Type)
Legacy Module Terminal Number (V-Type) 1 2 3 4 5 6 7 8 9 N/A N/A
Terminal Function SLC SLC + VDC VDC + Unused Solenoid B/A Solenoid B/A + Solenoid A + Solenoid A Unused Unused
Table C.2 CMF-300 and MMF-302 Terminal Conversions
68
MMF-300
C.3 MMF-300
Class A Supervision Class A Supervision+ Class A/B Supervision + Class A/B Supervision -
SLC SLC +
Class A Supervision Class A Supervision+ Class A/B Supervision + Class A/B Supervision -
SLC SLC +
Terminal Function SLC SLC + Unused Unused Unused Class A/B Supervision Class A/B Supervision + Class A Supervision + Class A Supervision Unused Unused
Table C.3 MMF-300 Terminal Conversions
69
MDF-300
C.4 MDF-300
Address +1 (H) Address +1 (H) + Base Address (L) + Base Address (L) LOOP LOOP
9 8 7
6 5
5 4 3 2
TENS
6 7 8 910 11 12 13 1 0 1514 8
0
1 2
SLC SLC +
4
2
ONES
3
0
4
ADDRESS ADDRESS
Address +1 (H) Address +1 (H) + Base Address (L) + Base Address (L) -
SLC SLC +
Terminal Function SLC SLC + Unused Unused Unused Base Address (L) Base Address (L) + Address +1 (H) + Address +1 (H) Unused Unused
Table C.4 MDF-300 Terminal Conversions
70
Appendix D: Intelligent Detector Base Layouts for Legacy Devices

D.1 B350LP or B501 Detector Base
SLC
2(+)
Use a female disconnect to wire the RA100Z/RA400Z () to Terminal 1 ().
1()
B501 only: For connection of cable shield
RA100Z/ RA400Z Remote LED Annunciator (Optional)
Figure D.1 Wiring the Legacy B350LP or B501 Detector Base
NOTE: The B350LP base wiring is identical to the B501, except there is no shield terminal.
71
SLC-B501wire.wmf
Intelligent Detector Base Layouts for Legacy Devices
B224BI Isolator Base
D.2 B224BI Isolator Base

SLC Out
SLC In
Conduit
SLC-224BIwire.wmf
I300 Isolator Module
Figure D.2 Wiring the Legacy B224BI Isolator Base
D.3 B224RB Relay Base

To next device on SLC For connection of cable shield
3 Relay Common 2 Normally Open 1 Normally Closed
SLC
Figure D.3 Wiring the Legacy B224RB Relay Base
72
b224rb.wmf
B501BH(-2) and B501BHT(-2) Sounder Bases
Intelligent Detector Base Layouts for Legacy Devices
D.4 B501BH(-2) and B501BHT(-2) Sounder Bases

UL-Listed 24V Power Supply
Optional Sounder Interconnect
SLC +
SLC -
Figure D.4 Wiring the Legacy B501BH(-2) and B501BHT(-2) Sounder Bases
slc-b501bhwiring.wmf
73
Appendix E: Canadian Versions of SLC Devices

UL-listed SLC Device AD350/AD355 CP350/CP355 ULC-listed SLC Device AD350A/AD355A CP350A/CP-355A Description Intelligent detector that combines a photoelectric sensing chamber and fixed temperature heat detection (135F/57.2C). Addressable, intelligent smoke detector that incorporates an ionization sensing chamber. Designed to provide open area protection. Addressable intelligent smoke detector that uses a photoelectric sensing chamber. Listed for use in ducts. Designed to provide open area protection. Adds thermal sensors that will alarm at a fixed temperature of 135F (57C). Intelligent thermistor sensing circuit for fast response. Designed to provide open area protection with 50 foot spacing capability. A fixed temperature sensor with 135F fixed temperature alarm. Incorporates a thermal rate of rise of 15F (9.4C). High temperature sensor with 190F (87.8C) fixed temperature alarm. Photoelectric Duct Detector, Low-flow. Requires SD350(A)/SD355(A) detector. Bases B210LP B501 B501BH, B501BHT B501BH-2, B501BHT-2 B224RB B224BI B200SR B210LPA B501A B501BHA, B501BHTA N/A B224RBA B224BIA B200SRA Standard U.S. Low-Profile base (6", 15.24 cm). Standard European flangeless base (4", 10.16 cm). Sounder base, includes Sounder base with temporal sounder (UL 8th Edition). Sounder base, includes Sounder base with temporal sounder (UL 9th Edition). Low Profile Intelligent relay base. Low Profile Intelligent isolator base. Intelligent sounder base, temporal or steady.
SD350/SD355
SD350A/SD355A
SD350T/SD355T H350/H355
SD350TA/SD355TA H350A/H355A
H350R/H355R H355HT
H350RA/H355RA H355HTA
Monitor and Zone Interface Modules MMF-300 MMF-300A Used for normally open contact alarm initiating devices, such as manual pull stations, four-wire smoke detectors, heat detectors, waterflow, and supervisory devices. Used to interface with two-wire smoke detectors in addition to normally open contacts. Two independent 2-wire Initiating Device Circuits (IDCs) at two separate, consecutive addresses. Wire supervised IDCs as NFPA Style B (Class B) or Style D (Class A) circuits. The modules come with a thermoplastic cover for mounting to a 4-inch (10.16 cm) square mounting box. Functionally similar to the MMF-300 Monitor Module, but offered in a smaller package for mounting directly in the electrical box of the device being monitored. (Class B input circuit only.) An addressable manual pull station with key-lock reset feature. The addressable module is housed within the pull station.
MMF-302 MDF-300
MMF-302A MDF-300A
MMF-301
MMF-301A
BG-12LX Control Modules CMF-300
BG-12LX
CMF-300A
Control Module, NAC: Addressable Control Module used as Notification Appliance Circuits (NACs) to power and supervise compatible, UL-listed notification appliances. Wired supervised NACs as NFPA Style Y (Class B) or Style Z (Class A). The modules come with a thermoplastic cover for mounting to a 4-inch (10.16 cm) square mounting box.
74
Canadian Versions of SLC Devices

UL-listed SLC Device CRF-300 Fault Isolator Module I300 I300A The Fault Isolator Module protects the system against wire-to-wire short circuits on the SLC. It should be placed between groups of sensors in a Style 6 or Style 7 SLC to isolate short- and open-circuit problems and protect the rest of the loop so it can continue to operate normally. It is not addressable, but listed here due to its use in an SLC. ULC-listed SLC Device CRF-300A Description Relay Control Module is similar to the CMF-300(A) except used as a Form-C control relay module.
Multi-input/output modules MMF-300-10 MMF-302-6 CDRM-300 CMF-300-6 CRF-300-6 MMF-300-10A MMF-302-6A CDRM-300A CMF-300-6A CRF-300-6A Supervises ten Class-B addressable Initiating Device Circuits (IDC) which monitor normally open contact initiating devices. Monitors six zones of conventional two-wire detectors. Dual Class B monitor / Form-C relay module. Similar in operation to the CMF-300, except it can activate six (6) Style Y (Class B) or three (3) Style Z (Class A) NACs. Similar in operation to the CRF-300, except it provides six (6) FormC relays.
75
Index
Numerics
24 VDC detectors 61 24 VDC NAC power 44 24 VDC power MS-9200, MS-9600 18 address setting 46 circuit board 48 installation 46 short circuit protection 47 Style selection 47 wiring 49 common ground 64 communication protocol 10 conduit, close nippled 26 connectors, crimp-on 65, 66 Control Modules 11 Overview 74 control panel 8 CP350 Detector 11 CP355 12 CP355 Detector 56 CRF-300 Relay Module 11, 51 wiring 51 CRF-300-6 Relay Module 11, 51 address disabling 53 address setting 53 circuit board 52 wiring 52, 53
A
AD350 Detector 11 AD355 Detector 11, 56 address capacity 23 addressable modules 11, 27 addressable devices 23 Addressable Modules (Overview) 74 Addressable Monitor Modules 27 Alarm Verification 56 analog intelligent devices 10 Authority Having Jurisdiction 13 auxiliary devices 11
B
B200SR Sounder Detector Base 56 B210LP 56 B224BI Isolator Detector Base 23, 56 B224RB Relay Detector Base 56 B350LP Detector Base 71 B501 Detector Base 56, 71 B501BH Sounder Detector Base 56 B501BH-2 Sounder Detector Base 56 B501BHT Temporal Sounder Detector Base 56 B501BHT-2 Temporal Sounder Detector Base 56 base 57, 58, 59 BEAM355 12 BEAM355S 12 BG-12LX 12, 60 building entry/exit 64
D
D350P Detector 12 D350RP Detector 12 D355PL detector 12 DC resistance 15, 16 detector bases 56 detector bases, wiring of 57 detectors 56 detector bases 74 listing 11, 74 devices addressable 23 auxiliary 11 maximum number between isolators 23 supervised 62 document sources 9 drain wire 17 dry-contact 11 DTK-2LVLP-F 64 Dual Monitor Module 31
C
CDRM-300 54 CDRM-300 Multiple Input/Output Module wiring 55 circuit fault 11 Classic Loop Interface Protocol 10 CLIP (Classic Loop Interface Protocol) 10 CLIP Mode 12 close nippled conduit 26 CMF-300 Control Module 11, 44, 45, 46 installation 44 wiring 45 CMF-300-6 Control Module 11, 44, 49, 50 address disabling 47
76
E
electrical interference 14 emergency signaling circuit 36 End-of-Line Resistor 45, 49
Index
FP
F
fault 13, 25 fault condition 23 Fault Isolator Module 23 FCPS-24F 61 Fire alarm service 31 foil 17 Form-C contacts 54 Form-C relay contacts 11, 51, 56 four-wire configuration 46, 50
G
ground terminal 65, 66
H
H350 Detector 12 H350R Detector 12 H355 Detector 12, 56 H355HT Detector 12 H355R Detector 12 Heat Detector 56
MMF-301 Mini Monitor Module 11, 31 MMF-302 Zone Interface Module 11, 29, 40, 41 wiring 40 MMF-302-6 Interface Module 11, 30, 42, 43 wiring 42 module circuits 27 modules addressable 11 control 11 isolator 11 monitor 11 relay 11 Monitor Modules 11, 27 Overview 74 Multicriteria Detector 56 multiple input/output module 54 Multi-Point Module 33
N
NAC 11 NAC power 44, 62 NAC wiring 44 NEC Article 800 64 NFPA Style 4 wiring of 21 with I300 24 NFPA Style 6 wiring of 22 with I300 25 NFPA Style 7 23 with isolator modules 26 NFPA Style B IDC wiring 34, 37, 39, 40, 42 NFPA Style D IDC wiring 35, 38, 41, 43 NFPA Style Y 44 wiring of 45, 49 NFPA Style Z 44 wiring of 46, 50 Nonresettable power 18 normally closed contacts 62 Notification Appliance Circuit 11
I
I300 Isolator Module 11, 23 Initiating Device Circuits 27, 34, 37, 39 integral relay 23 Ionization Detector 56 isolator base 23 isolator base, wiring of 58 Isolator Module 11, 25, 26 how it works 23 wiring of 23
K
key-lock reset 60
L
LEDs 56 LiteSpeed 10 local building code 64 loop resistance 15, 16 loops 16
O
older version and newer version modules 8, 9
M
MDF-300 Dual Monitor Module 11, 31, 39 wiring 39 metal conduit 17, 25 Mini Monitor Module 31 minimum resistance 61 MMF-300 Monitor Module 11, 27, 34, 35, 36 wiring 34 MMF-300-10 Monitor Module 11, 28, 37, 38 wiring 37
P
performance 13 Photoelectric Detector 56 PLP-42N 64 Polling Protocols 10 power run 61, 62 power supervision relay 45, 46, 49, 50, 62 power supplies 61 proper gauge wire 61
77
RZ
Index
pull station 12, 26 wiring of 60
two-wire configuration 45, 49 two-wire detectors 62
R
RA100Z 57 RA400Z 57 rate of rise 12 ratings, relay contact 44, 51, 54 relay base 23 wiring of 58 relay contact ratings 44, 51, 54 Relay Module 11 relays Form-C 11 Remote LED Annunciator 57 Resettable power 18 resistance 15, 16 rotary switches 32, 38, 39, 40, 41, 42, 43, 56
U
Unregulated power 18
V
verification cycle 56
W
Waterflow alarm service, automatic and manual 31 wire length 15, 16 wire size 14 wiring I300 23 MDF-300 39 MMF-300 34 MMF-300-10 37 MMF-302 40 MMF-302-6 42 NACs 44 wiring pair 64 wiring requirements 14 wiring style requirements 13
S
SD350 Detector 12 SD350T Detector 12 SD355 Detector 12, 56 SD355R Detector 12 SD355T Detector 12 sensing circuit, thermistor 12 short circuit 23 Signaling Line Circuit 10 Single Point Module 32 SLC address, setting of 32, 56 SLC connections 18 SLC terminal block 17 SLC wiring 34, 35, 36, 37, 38, 39, 40, 41, 42, 43 SLCP-30 64 Smoke Detectors 56 sounder base 23 sounder base, wiring of 59 Sprinkler supervision 31 supervised circuit 62 devices 62 supplying power 61 suppressors, surge 64 surge protector 10, 13, 64 switching 44
Z
Zone Interface Module 29
T
terminal blocks 18 termination of shield 17 Thermal Detector 56 thermistor sensing circuit 12 trouble conditions 13, 23 T-tapping 15, 21, 22, 25, 26 twisted-pair shielded wiring 14
Manufacturer Warranties and Limitation of Liability

Manufacturer Warranties. Subject to the limitations set forth herein, Manufacturer warrants that the Products manufactured by it in its Northford, Connecticut facility and sold by it to its authorized Distributors shall be free, under normal use and service, from defects in material and workmanship for a period of thirty six months (36) months from the date of manufacture (effective Jan. 1, 2009). The Products manufactured and sold by Manufacturer are date stamped at the time of production. Manufacturer does not warrant Products that are not manufactured by it in its Northford, Connecticut facility but assigns to its Distributor, to the extent possible, any warranty offered by the manufacturer of such product. This warranty shall be void if a Product is altered, serviced or repaired by anyone other than Manufacturer or its authorized Distributors. This warranty shall also be void if there is a failure to maintain the Products and the systems in which they operate in proper working conditions. MANUFACTURER MAKES NO FURTHER WARRANTIES, AND DISCLAIMS ANY AND ALL OTHER WARRANTIES, EITHER EXPRESSED OR IMPLIED, WITH RESPECT TO THE PRODUCTS, TRADEMARKS, PROGRAMS AND SERVICES RENDERED BY MANUFACTURER INCLUDING WITHOUT LIMITATION, INFRINGEMENT, TITLE, MERCHANTABILITY, OR FITNESS FOR ANY PARTICULAR PURPOSE. MANUFACTURER SHALL NOT BE LIABLE FOR ANY PERSONAL INJURY OR DEATH WHICH MAY ARISE IN THE COURSE OF, OR AS A RESULT OF, PERSONAL, COMMERCIAL OR INDUSTRIAL USES OF ITS PRODUCTS. This document constitutes the only warranty made by Manufacturer with respect to its products and replaces all previous warranties and is the only warranty made by Manufacturer. No increase or alteration, written or verbal, of the obligation of this warranty is authorized. Manufacturer does not represent that its products will prevent any loss by fire or otherwise. Warranty Claims. Manufacturer shall replace or repair, at Manufacturer's discretion, each part returned by its authorized Distributor and acknowledged by Manufacturer to be defective, provided that such part shall have been returned to Manufacturer with all charges prepaid and the authorized Distributor has completed Manufacturer's Return Material Authorization form. The replacement part shall come from Manufacturer's stock and may be new or refurbished. THE FOREGOING IS DISTRIBUTOR'S SOLE AND EXCLUSIVE REMEDY IN THE EVENT OF A WARRANTY CLAIM.
Warn-HL-08-2009.fm
79
World Headquarters 1 Firelite Place Northford, CT 06472-1653 USA 203-484-7161 fax 203-484-7118 www.firelite.com

SLC Wiring Manual

Uploaded by

Copyright:

Available Formats

SLC Wiring Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SLC Wiring Manual

Uploaded by

Copyright:

Available Formats

Intelligent Control Panel

Document 51309 10/12/2011 Rev:

Fire Alarm System Limitations

FireLite SLC Wiring Manual P/N 51309:P1 10/12/2011

FireLite SLC Wiring Manual P/N 51309:P1 10/12/2011

FireLite SLC Wiring Manual P/N 51309:P1 10/12/2011

Section 2: Wiring Requirements............................................................................................ 14

Section 3: SLC Circuits without Isolators ............................................................................ 21

Section 4: SLC Circuits with Isolators .................................................................................. 23

Section 5: Monitor Modules ................................................................................................... 27

FireLite SLC Wiring Manual P/N 51309:P1 10/12/2011

Section 6: Control Modules ................................................................................................... 44

Section 7: Relay Modules ...................................................................................................... 51

Section 8: Multiple Input/Output Modules............................................................................ 54

FireLite SLC Wiring Manual P/N 51309:P1 10/12/2011

Section 9: Intelligent Detector Bases.................................................................................... 56

Section 10: Addressable Manual Pull Station ...................................................................... 60

Appendix A: Power Considerations...................................................................................... 61

Appendix B: Surge Suppression........................................................................................... 64

Appendix C: Terminal Conversion Charts for New & Legacy Devices.............................. 67

Appendix D: Intelligent Detector Base Layouts for Legacy Devices ................................. 71

Appendix E: Canadian Versions of SLC Devices ................................................................ 74 Index........................................................................................................................................ 76

FireLite SLC Wiring Manual P/N 51309:P1 10/12/2011

CMF-300 Legacy Version Module (Vertical Rotary Dial)

CMF-300 Newer Version Module (Horizontal Rotary Dial)

FireLite SLC Wiring Manual P/N 51309:P1 10/12/2011

1.1.1 Reference Documentation

FireLite SLC Wiring Manual P/N 51309:P1 10/12/2011

Table 1.1 Reference Documentation

1.3 Polling Protocols

1.3.1 Available Protocols

1.3.2 Protocol Use

FireLite SLC Wiring Manual P/N 51309:P1 10/12/2011

1.4.2 Monitor Modules

1.4.3 Control Modules

1.4.4 Relay Modules

1.4.5 Multiple Input/Output Modules

1.4.6 Intelligent Detectors

1.4.7 Manual Pull Station

1.4.8 300 Series Addressable Devices

1.5 SLC Capacity

1. Addressable Heat Detectors are not compatible with the MS-9200(E).

1.6 SLC Performance

Table 1.2 SLC Performance

1.7 Surge Suppression

1.8 LED Operation

Table 1.3 LED Operation

FireLite SLC Wiring Manual P/N 51309:P1 10/12/2011

Section 2: Wiring Requirements

2.1.1 CLIP (Classic Loop Interface Protocol) Mode

3,225 feet (983 m)

18 AWG (0.75 mm2)

Table 2.1 SLC Wiring Requirements in CLIP Mode

2.1.2 LiteSpeed Mode

Table 2.2 SLC Wiring Requirements in LiteSpeed Mode

FireLite SLC Wiring Manual P/N 51309:P1 10/12/2011

Measuring Resistance & Length

2.2 Measuring Resistance & Length

Figure 2.1 Measuring DC Resistance of a Two-Wire SLC

Total Wire Length