Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 382 views

    12 Procedure For Coating Wrapping Rev 01

    Uploaded by

    dnbinh
    This 6-page document outlines procedures for coating and wrapping underground carbon steel pipelines. It describes surface preparation through grit blasting, priming, applying two coats of coal tar enamel and glass fiber wraps using a machine for pipes 10-48 inches in diameter. Inspection includes checking coating thickness and holiday testing at 13kV. Damaged coatings are repaired by removing wraps and coating, then reapplying. Coated pipes must be handled carefully and supported during storage. Safety precautions like PPE and fire equipment are required.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    12 Procedure For Coating Wrapping Rev 01

    Uploaded by

    dnbinh
    382 views6 pages
    This 6-page document outlines procedures for coating and wrapping underground carbon steel pipelines. It describes surface preparation through grit blasting, priming, applying two coats of coal tar enamel and glass fiber wraps using a machine for pipes 10-48 inches in diameter. Inspection includes checking coating thickness and holiday testing at 13kV. Damaged coatings are repaired by removing wraps and coating, then reapplying. Coated pipes must be handled carefully and supported during storage. Safety precautions like PPE and fire equipment are required.

    Original Title

    12 Procedure for Coating Wrapping Rev 01

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This 6-page document outlines procedures for coating and wrapping underground carbon steel pipelines. It describes surface preparation through grit blasting, priming, applying two coats of coal tar enamel and glass fiber wraps using a machine for pipes 10-48 inches in diameter. Inspection includes checking coating thickness and holiday testing at 13kV. Damaged coatings are repaired by removing wraps and coating, then reapplying. Coated pipes must be handled carefully and supported during storage. Safety precautions like PPE and fire equipment are required.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    382 views6 pages

    12 Procedure For Coating Wrapping Rev 01

    Uploaded by

    dnbinh
    This 6-page document outlines procedures for coating and wrapping underground carbon steel pipelines. It describes surface preparation through grit blasting, priming, applying two coats of coal tar enamel and glass fiber wraps using a machine for pipes 10-48 inches in diameter. Inspection includes checking coating thickness and holiday testing at 13kV. Damaged coatings are repaired by removing wraps and coating, then reapplying. Coated pipes must be handled carefully and supported during storage. Safety precautions like PPE and fire equipment are required.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 6
    At a glance
    Powered by AI
    The document describes guidelines for coating and wrapping of underground carbon steel pipelines with protective tapes and materials.

    The purpose of this procedure is to describe guidelines to carry out tape coating of underground piping at IOCL PANIPAT REFINERY – MSQ UPGRADATION PROJECT.

    The main steps involved are surface preparation through grit blasting, priming, preparation and heating of coating material, application of multiple layers of heated coal tar enamel and wraps, inspection and testing.

    PAGE NO.

    - 1 OF 6

    LARSEN & TOUBRO LIMITED MSQ UP GRADATION (EPCC 1) PROJECT


    PROCEDURE FOR COATING AND WRAPPING OF UNDERGROUND CARBON STEEL PIPELINES.

    DATE:-05.01.2008 REV.NO.- 01
    PROCEDURE NO.LT/MSQ/P/UG/CW/012

    CONTENTS

    1) PURPOESE 2) REFERENCE DOCUMENTS 3) MATERIALS 4) PROCEDURE 5) INSPECTION 6) REPAIR 7) MACHINE LIMITATION 8) HANDLING OF COATED PIPES
    9) SAFETY PRECAUTIONS

    APPROVED BY L & T

    REVIEWED / APPROVED BY JACOBS

    PAGE NO.- 2 OF 6

    LARSEN & TOUBRO LIMITED MSQ UP GRADATION (EPCC 1) PROJECT


    PROCEDURE FOR COATING AND WRAPPING OF UNDERGROUND CARBON STEEL PIPELINES.

    DATE:-05.01.2008 REV.NO.- 01
    PROCEDURE NO.LT/MSQ/P/UG/CW/012

    1.0 PURPOSE

    1.1.
    1.2.

    This procedure describes guidelines to carry out tape coating of UG piping at IOCL PANIPAT REFINERY MSQ UPGRADATION PROJECT. In case of conflict between this procedure and contract specification, the latter shall govern.

    2.0 REFRENCE DOCUMENTS:

    2.1. 2.2. 2.3.


    2.4.

    As per Jacobs spec. No. 3177-LSS-109 AWWA C-203 Coal tar protective coating lining to steel carbon pipeline SSPC-SP10 steel structure Painting council, surface preparation specification ASTM G8 test method for cathodic disbanding of pipeline coating 3.0 MATERIALS:

    3.1. 3.2.

    Protective tapes and other materials brought to site shall be as per specification. Manufacturers test certificates shall be submitted for review prior to use. The primer shall be type B as specified in AWWA C-203. Field and laboratory test shall be carried out for each batch of primer & tape. Primer and tape shall be supplied by the same manufacturer. 4.0 PROCEDURE:

    3.3.
    3.4. 3.5.

    4.1. 4.1.1.

    SURFACE PREPARATION:

    Prior to blast cleaning, all oil, grease on the pipe surface shall be thoroughly removed by flushing with suitable solvent as per SSPC SP-1 and wiping with clean tags. Degreased pipe metal surface shall be shot/grit blast cleaned to SSPC-SP-10 or Sa 2 of SIS-05-5900. This cleaning operation shall be followed immediately with priming by spraying / brush.

    APPROVED BY L & T

    REVIEWED / APPROVED BY JACOBS

    PAGE NO.- 3 OF 6

    LARSEN & TOUBRO LIMITED MSQ UP GRADATION (EPCC 1) PROJECT


    PROCEDURE FOR COATING AND WRAPPING OF UNDERGROUND CARBON STEEL PIPELINES.

    DATE:-05.01.2008 REV.NO.- 01
    PROCEDURE NO.LT/MSQ/P/UG/CW/012

    4.1.2. 4.1.3.

    Blast cleaned surface shall be adequately scrubbed manually with stiff wire brush where ever blasted surface get rusted, prior to application of primer. All weld joints shall be cleaned manually with stiff wire brush/buffing wheel after assembly and welding, prior to priming.

    4.2.

    PRIMING:

    4.2.1.
    4.2.2.

    Immediately after girt blasting the surface shall be applied with fast drying unmodified pure chlorinated rubber based coal tar synthetic primer. Second coat of primer to be applied before application of coal tar enamel. The entire surface of pipe should be primed. No specific time gap between two coats of primer needs to be maintained but after the second coat of primer, the enamel coating should before the primer is completely hardened.

    4.3.

    PREPARATION OF COATING MATERIAL: The metal drums that shall be cropped or cut on suitable platform to prevent the enamel coming in contact with wooden cinders, grass and other forms of contamination. The enamel shall be confirmed to Type-I or Type-II coal tar enamel as per AWWA C-203. The cropped out pieces if enamel may not Wight more then 10 kgs. The broken pieces shall be placed in a clean melting kettle which is made of heavy duty, MS sheet in form of closed vessel. To maintain uniform coverage of material required quantity of enamel is heated in the kettle with temperature range of 2300C to 2400C. Temperature of enamel can be checked by dipping thermometer in the enamel. Thermometer shall be used in heating kettle in a such way so as read the temperature clearly. The thermometer shall have temperature range up to 3000C.

    APPROVED BY L & T

    REVIEWED / APPROVED BY JACOBS

    PAGE NO.- 4 OF 6

    LARSEN & TOUBRO LIMITED MSQ UP GRADATION (EPCC 1) PROJECT


    PROCEDURE FOR COATING AND WRAPPING OF UNDERGROUND CARBON STEEL PIPELINES.

    DATE:-05.01.2008 REV.NO.- 01
    PROCEDURE NO.LT/MSQ/P/UG/CW/012

    4.4.

    MECHANICAL APPLICATION OF COATING AND WRAPPING :

    4.4.1.

    The pipe shall be kept rotating on a machine having circumferential and linear motions, while the pipes are in rotating condition, pour the hot cold enamel manually and spread uniformly with the help of rubber brushes.

    4.4.2.

    Simultaneously, one wrap of glass fibre tissue having properties as stated in Jacobs specification shall be applied over the molten coal tar enamel. Initially, the wrap is held with hand and pressed over the molten enamel. There after the revolving pipe puffs the fiber warp from the reel, which ensures continuous wrapping over the molten enamel with required overlap (i.e. 13 mm).

    4.4.3.
    4.4.4.

    Second coat of coal tar enamel as well as glass fiber tissue paper shall be applied as per above procedure. Third coat of molten coal tar enamel shall be applied next. Final outer wrap of impregnated fibre felt shall be applied immediately over third coat of coal tar enamel, similar to inner wrap application. The overlap at edges of all wrappings should be minimum 13 mm. the coating shall be continuous for the full length of the pipe except 200 mm at both ends of the pipes. Finally, carry out whit wash with Acrylic water emulsion Latex Paint Material. This application will be carried out manually by paintbrushes. There after the pipes is lifted by suitable methods and allowed to dry on wooden sleepers.

    5.0 INSPECTION:

    5.1.

    All stage inspection & documentation shall be carried out as per Format No. LT/MSQ/TC/020, Rev.00 Profile gauge/comparator, for checking surface preparation as per SA 2 , shall be made available.

    5.2.

    After application of tape coating, visual inspection shall be carried out for uniformity without any wrinkle, irregularities and overlapping width.

    APPROVED BY L & T

    REVIEWED / APPROVED BY JACOBS

    PAGE NO.- 5 OF 6

    LARSEN & TOUBRO LIMITED MSQ UP GRADATION (EPCC 1) PROJECT


    PROCEDURE FOR COATING AND WRAPPING OF UNDERGROUND CARBON STEEL PIPELINES.

    DATE:-05.01.2008 REV.NO.- 01
    PROCEDURE NO.LT/MSQ/P/UG/CW/012

    5.3. 5.4.

    Thickness of the coal tar enamel coating shall be measured with the digital thickness gauge. Minimal acceptable thickness shall be 4.5mm. All coated and wrapped pipes shall be tested with the positive signalling device to indicate any fault, holes, breaks or conductive particles in the protective coating. The test voltage shall be 13 KV.

    5.5.

    Peel test shall be conducted at temperature from 10C to 25C per AWWA-203 methods. Acceptable criteria shall be as per AWWA-203.

    6.0 REPAIR: Wherever any holiday is observed or any defective work is found, remove the wrapping and coating to the required extend from those areas by using a sharp knife. Then heated enamel shall be applied manually over the area following the procedure described above and inner and outer wrap applied. Holidays test shall repeated for the portion.

    7.0 MACHINE LIMITATION:


    Machine used for coating and wrapping as described above can be used from pipes from 10 to 48 only. For pipes upto 8 and above 48 , coating and wrapping shall be done manually with out rotation of pipes. 8.0 HANDLING OF COATED PIPES The coated pipes shall be handled at all times with equipments such as wide belt slings and padded skids designed to prevent damage to the coating. Bare cables, chains, hooks etc. shall not be permitted to come in contact with coatings. A suitable crane may be used. Coated pipes shall be supported at two bare ends clear from ground either on kids or sand bags.

    APPROVED BY L & T

    REVIEWED / APPROVED BY JACOBS

    PAGE NO.- 6 OF 6

    LARSEN & TOUBRO LIMITED MSQ UP GRADATION (EPCC 1) PROJECT


    PROCEDURE FOR COATING AND WRAPPING OF UNDERGROUND CARBON STEEL PIPELINES.

    DATE:-05.01.2008 REV.NO.- 01
    PROCEDURE NO.LT/MSQ/P/UG/CW/012

    9.0 SAFETY PRECAUTIONS 9.1.


    9.2. 9.3. Adequate and proper PPE shall be provided to persons involved in short of grit blasting work. Adequate and proper PPE shall be provided to persons involved in hot application of coal tar enamel along with the wraps. Proper fire fighting system shall be provided during application of primer and enamel coats and all safety requirements shall be ensured for under ground trenching, lowering & back filling. 9.4 All precaution shall be observed as per the instruction of PMC/ OWNER.

    APPROVED BY L & T

    REVIEWED / APPROVED BY JACOBS

    You might also like