Liquid ring compressors

LOH 25003, LOH 25007, LOH 25309

Compression pressure: Suction volume flow:

0,2 to 2 bar 12 to 58 m/h

Sterling SIHI liquid ring compressors are displacement compressors of simple and robust construction. They have the following important features: Handling of nearly all gases and vapours non-polluting due to nearly isothermal compression oil-free, as no lubrication in the working chamber additional liquid can be handled with the gas flow easy in maintenance and reliable operation low noise and nearly free of vibrations wide choice of material, therefore applicable nearly everywhere incorporated central drain no metallic contact of the rotating parts The Sterling SIHI liquid ring compressors LOH 25003, LOH 25007 and LOH 25309 are two-stage compressors. They can be applied without modification as vacuum pump up to a suction pressure of 40 mbar (see catalogue part LI2). APPLICATION Handling and compressing of dry and humid gases; entrained liquid can be handled during normal duty. The compressors are applied in all fields where a compression over pressure of up to 1 bar has to be created by robust compressors and only a small increase in temperature is admissible during compression. Fields of application are e.g.: - the plastics industry, for the recovery of process gases as vinyl chloride - the petrochemical industry, for the compression of combustible gases as gasoline vapours or hydrogen - transport of gases in general, e.g. to a reactor

NOTE During operation the compressor must continuously be supplied with service liquid, normally water, in order to eliminate the heat resulting from the gas compression and in order to replenish the liquid ring, because part of the liquid is leaving the compressor together with the gas. This liquid can be separated from the gas in a pressure liquid separator ( see catalogue part accessories). It is possible to reuse the service liquid. The direction of rotation is clockwise, when looking from the drive on the pump.

GENERAL TECHNICAL DATA Pump type Speed Max. compression over pressure hydraulic test (over pressure) Moment of inertial of the rotating pump parts and the water filling Sound pressure level of measuring area Min. pulley diameter permissible in case of V-belt drive Max. gas temperature Service liquid max. admissible temperature max. viscosity max. density volume up to shaft level The combination of several limiting values is not admissible. dry saturated 50 Hz 60 Hz unit rpm bar bar kg m dB (A) mm C C C mm/s kg/m liter
.

LOH 25003 2800 3400

LOH 25007 2800 3400 2,6 4

LOH 25309 2900 3500

0,004 70 71 80 90

0,0065 70 71 80 90 200 100 100 90 1200 1,2

0,00875 70 71 112

1,4

133.72115.52.01 E

VACUUM TECHNOLOGY KPH K 3 08/2000

Material design
MATERIAL DESIGN 02 0.6025 0.6025 / 1.0570 0.6025 Rg9 1.4021 Cr Ni-steel / carbon / Perbunan 1.4027.05 1.4517 1.4401 Cr Ni Mo-steel / carbon / Viton 1.4408

Pos. 0001, 0002 0035, 0036 0010, 0011, 0012, 0013 0030, 0031 0200 0500, 0600

COMPONENTS Casing Central body Guide disk Vane wheel impeller Shaft Mechanical seal

01

42

Sectional drawing LOH 25003, LOH 25007, LOH 25309

Suction volume flow and power absorption LOH 25003

25 m/h 20 suction volume flow

15
2800 rpm 3400 rpm

10

LOH 25003 5 0 0,4 0,8 1,2 1,6 2 bar 2,4 compression over pressure

3 kW 2,5 power absorption 2 1,5 1 0,5 LOH 25003 0 0 0,4 0,8 1,2 1,6 2 bar 2,4 compression over pressure
2800 rpm 3400 rpm

The values indicated for volume flow and power absorption are valid for compression of dry air at 20C from atmospheric pressure (1013 mbar) to the respective compression pressure with water at 20C as service liquid. Tolerance of the curve values is 10 %. The compression pressure in bar is indicated as pressure above the atmospheric pressure. The data indicated change with deviating service conditions, such as deviating physical data of the gas to be handled or of the service liquid (vapour pressure, temperature, density, viscosity) when handling entrained liquid, at a suction pressure deviating from atmospheric pressure, when handling gas-vapours mixtures. For determination of service data for deviating service conditions please see catalogue section TH.

Suction volume flow and power absorption LOH 25007

60 m/h 50 suction volume flow

40

30

2800 rpm

3400 rpm

20 LOH 25007 10 0 0,4 0,8 1,2 1,6 2 bar 2,4 compression over pressure

5 kW 4 power absorption
3400 rpm

2800 rpm

1 LOH 25007 0 0 0,4 0,8 1,2 1,6 2 bar 2,4 compression over pressure

The values indicated for volume flow and power absorption are valid for compression of dry air at 20C from atmospheric pressure (1013 mbar) to the respective compression pressure with water at 20C as service liquid. Tolerance of the curve values is 10 %. The compression pressure in bar is indicated as pressure above the atmospheric pressure. The data indicated change with deviating service conditions, such as deviating physical data of the gas to be handled or of the service liquid (vapour pressure, temperature, density, viscosity) when handling entrained liquid, at a suction pressure deviating from atmospheric pressure, when handling gas-vapours mixtures. For determination of service data for deviating service conditions please see catalogue section TH.

Suction volume flow and power absorption LOH 25309

70 m/h 60 suction volume flow

50
2900 rpm

40

30 LOH 25309 20 0 0,2 0,4 0,6 0,8 1 1,2 bar 1,4 compression over pressure

5 kW 4 power absorption
3500 rpm

2900 rpm

1 LOH 25309 0 0 0,2 0,4 0,6 0,8 1 1,2 bar 1,4 compression over pressure

The values indicated for volume flow and power absorption are valid for compression of dry air at 20C from atmospheric pressure (1013 mbar) to the respective compression pressure with water at 20C as service liquid. Tolerance of the curve values is 10 %. The compression pressure in bar is indicated as pressure above the atmospheric pressure. The data indicated change with deviating service conditions, such as deviating physical data of the gas to be handled or of the service liquid (vapour pressure, temperature, density, viscosity) when handling entrained liquid, at a suction pressure deviating from atmospheric pressure, when handling gas-vapours mixtures. For determination of service data for deviating service conditions please see catalogue section TH.

Dimension drawing LOH 25003, LOH 25007

N1 N2 uB ue

= gas inlet G 1 = gas outlet G 1 = connection for service liquid G 3/8 = drain connection G a m m o3 348 398 weight abt. kg 22 23

LOH 25003 LOH 25007

163 213

309 359

279 329

Dimensional drawing LOH 25309

N1 N2 uB ue

= gas inlet G 1 = gas outlet G 1 = connection for service liquid G = drain connection G

u m1 = connection for drain valve G

Fresh water requirements

in [m/h] dependent on compression pressure, speed, mode of operation and difference in temperature compression pressure in bar 0,4 0,8 KB FB 5 difference in temperature [C] 30 20 10 5 0,3 0,3 0,6 FB KB difference in temperature [C] 30 20 10 5 0,4 0,4 0,8 0,03 0,05 0,08 0,14 0,04 0,06 0,11 0,17 0,06 0,08 0,13 0,20 0,07 0,10 0,16 0,23 0,08 0,12 0,21 0,33 0,11 0,15 0,26 0,39 FB 1,2 2,0 KB difference in temperature [C] 30 20 10 5 0,6 0,6 FB

pump

speed [rpm]

KB difference in temperature [C] 30 20 10

LOH 25003 LOH 25007 LOH 25309

2800 3400 2800 3400 2900 3500

0,02 0,03 0,05 0,08 0,18 0,03 0,04 0,07 0,11 0,03 0,04 0,07 0,10 0,05 0,06 0,09 0,12 0,05 0,07 0,11 0,16 0,06 0,08 0,13 0,18 0,3 0,04 0,05 0,09 0,14 0,06 0,09 0,13 0,18 0,07 0,10 0,17 0,26 0,09 0,12 0,20 0,30 0,03 0,05 0,07 0,10 0,18 0,04 0,06 0,10 0,15

0,06 0,09 0,15 0,24 0,11 0,15 0,24 0,34

FB = fresh liquid service KB = combined fresh liquid service 30 C, 20 C, 10 C, 5 C warmer than the fresh water.

Data regarding the size - order notes

25003 LOH 25007 25309 BN 131

Accessories
Recommended accessories Pressure liquid separator material design service liquid line material design discharge line material design Liquid discharge trap material design hanging gas line material design 072 / St 37-0 SIHI part No. size power weight size power weight Coupling for motor IP 55 pump side motor side for motor EEx e ll T3 pump side motor side Safety contact device material design Base frame material design 081 / 1.0038 type / weight SIHI part No. S008 / 10 kg 43 040 648 S241 / 24 kg 43 040 631 076 / 1.0330 345 / 2.0321 SIHI part No. SIHI part No. 43 042 201 43 042 202 43 042 206 43 042 205 43 042 245 type / weight SIHI part No. SIHI part No. type / weight SIHI part No. SIHI part No. 80 B 1,1 kW 10 kg 80 B 1,1 kW 12 kg 90 S 1,5 kW 13 kg 90 S 1,5 kW 14 kg upon request 90 L 2,2 kW 16 kg 90 L 1,85 kW 16 kg 100 L 3 kW 23 kg 100 L 2,5 kW 22 kg 100 L 3 kW 23 kg 112 M 3,3 kW 28 kg B80 / 1,5 kg 43 021 409 43 021 417 BDS88 / 1,9 kg 43 024 676 43 024 707
BDS103/3,1 kg

LOH 25003 type / weight 130 / galvanized 172 / 1.4571 072 / St 37-0 172 / 1.4571 072 / St 37-0 172 / 1.4571 type / weight SIHI part No. SIHI part No. upon request 35 003 088 SIHI part No.

LOH 25007 XBd 0413 / 28 kg 35 000 298 35 000 299 upon request 35 003 089 35 003 167 35 003 168 XUk 1602 / 11 kg 43 014 792

LOH 25309

upon request 35 003 090

762/ 0.6020+1.4541

SIHI part No.

Motor in case of standard design IP 55

112 M 4 kW 30 kg 132 S 4,6 kW 50 kg

EEx e ll T3

B68 / 0,6 kg 43 021 400 43 021 404 | 43 021 405 BDS76 / 0,8 kg 43 025 689 43 025 690 | 43 025 930

43 025 935 43 025 941

for motor 100+112 :

S272 / 28 kg 43 040 633

43 040 635

Any changes in the interest of technical development are reserved.

Sterling SIHI GmbH Lindenstrae 170, D-25524 Itzehoe, Germany, Telephone +49 (0) 48 21 / 7 71 - 01, Fax +49 (0) 48 21 / 7 71 - 2 74