Experiment 2 Wave Shaping Circuits

EXPERIMENT 2: WAVESHAPING CIRCUITS
I. OBJECTIVE
To investigate the clipping and clamping of sinusoidal signal using silicon diode.
II. BASIC CONCEPT

Diode can be used in wave-shaping circuit that limits a portion of a signal or shift the dc voltage level. These are the diode clipper and the diode clamper are examples of wave-shaping circuit. The diode clipper prevents the output voltage from exceeding a given value. It clips those portions of a signal that are above or below the reference level. The diode clamper circuit shifts the entire waveform by a dc level without changing the original waveform.
III. MATERIALS
Quantity
1 2 1 1 1 1 1 1 1 1set
Description
15-K resistor (1/2 watt) 1N4001 silicon diode 5 K Potentiometer or 10-Turn Trimpot 1 uF (16V) Breadboard Dual Trace Oscilliscope Power Supply Signal Generator Multimeter Connecting wires
IV. WIRING DIAGRAMS

Oscilloscope Function Generator 6V/200Hz
A + _ + B _ Ext T rig + _
R1 15k D1 1N4001 1 2 XSC1 0 XFG1
Figure 2.1 Positive Clipper

A + _ + B _ Ext T rig + _
R1 15k D1 1N4001
2 XSC1
Figure 2.2 Negative Clipper
XFG1 1 0

A + _ + B _ Ext T rig + _
R1 15k D1 1N4001 4 3 XSC1 5k Key=A R2 50%
15 V 5k 1 XFG1 V1 2 0
Figure 2.3 Positive Biased Clipper

R3

A + _ + B _ Ext T rig + _
R1 15k D1 1N4001 15 V 5k 3 XFG1 4 1 0 XSC1 2 5k Key=A R2 50%
V1
Figure 2.4 Negative Biased Clipper

R3

A + _ + B _ Ext T rig + _
1uF D1 1N4001 R1 10k 12 XSC1 XFG1
Figure 2.5 Clamper Circuit
V. PROCEDURE
A. DIODE CLIPPER 1. Connect the clipper circuit as shown in Figure 2.1. Set your oscilloscope to the following settings: Channels 1 and 2: 1V/division, DC coupling Time Base: 1ms/Division 2. Connect the signal generator to the clipper circuit. Adjust the signal generators output at 6V peak-to-peak at a frequency of 200Hz. On the data page and results section, sketch your clipped waveform, showing the positive and negative peak values. Label properly. 3. Now reverse the polarity of the diode in the circuit as shown in the Figure 2.2. How does this waveform compare with that of step 2. Sketch your clipped waveform showing the positive and negative peak values. 4. Now connect the circuit of Figure 2.3. Apply power and adjust the potentiometer so that the DC voltage (VDC) is +1.5V. Connect the signal generator set at 6Vp-p. What do you notice about the output of the clipper? On the data page and results section, sketch your clipped waveform showing the positive and negative peak values. 5. Vary the resistance of the potentiometer from one extreme to the other. What happens to the clipping level?
6. Now reverse the polarities of both the diode and the DC power supply in the circuit as shown in Figure 2.4. Adjust the potentiometer so that the DC voltage (VDC) is +1.5V. Connect the signal generator set at 6Vp-p. What do you notice about the output of the clipper? On the data page and results section, sketch your clipped waveform showing the positive and negative peak values. 7. Vary the resistance of the potentiometer from one extreme to the other. What happens to the clipping level?
B. DIODE CLAMPER 1. Connect the clamper circuit as shown in Figure 2.5. Set your oscilloscope to the following settings: Channels 1 and 2: 2V/division, DC coupling Time Base: 0.2ms/Division 2. Connect the signal generator to the clamper circuit. Adjust the signal generators output level at 5V peak-to-peak at a frequency of 1KHz. You should see two sine waves. On the space provided at the data and results section, sketch the input and output waveforms, showing the positive and negative peak values for both. 3. Slowly increase the peak-to-peak input voltage and observe what happens. 4. Now reverse the polarity of the diode in Figure 2.5 and repeat steps 2, 3 and 4. Now what happens? On the space provided at the data and results section sketch both input and output waveforms showing the positive and the negative peak values for both. 5. Slowly increase the peak-to-peak voltage and observe what happens.
VI. DATA AND RESULTS

Table 2.1 CIRCUIT + Clipper -Clipper + Biased Clipper -Biased Clipper Clamper Vin(Vp-p) Vout(Vp-p) Measured Value Vout(Vp-p) Expected Value %Difference
VII. SAMPLE COMPUTATIONS
PEDROSO, ELVIN LOUIE R. IX. ANALYSIS OF RESULTS
X. CONCLUSIONS
XI. SELF-TEST QUESTIONS

1. For the positive clipper of Figure 2.1, the positive peak voltage is approximately a. 0V b. +3V c. +0.6V d. +6V 2. For the negative clipper of Figure 2.2, the positive peak are not clipped because the diode is a. Negative Biased b. Forward Biased 3. In all clipping circuits in this experiment, the 15-K resistor is used to a. set the clipping level b. set the peak output voltage c. limit the voltage across the diode d. limit the forward current 4. For the circuit in Figure 2.3, the potentiometer is used to set the clipping level of the outputs a. positive peaks b. negative peaks c. positive and negative peaks 5. For the circuit in figure 2.4, the potentiometer is used to set the clipping level of the outputs a. positive peaks b. negative peaks c. positive and negative peaks
5. In the experiment, the rectifier circuit that has the greatest DC output voltage is the a. half-wave rectifier b. full-wave center-tapped rectifier c. full-wave bridge rectifier
XII. APPLICATIONS (CIRCUIT SIMULATION)

1. Design a clamper to perform the function indicated by the figure below. Ideal Diod es 20 V Vi n 20 V (+ ) V i Desi gn
30V (+)
Vout 10V
(-)
(-)
2. Perform an analysis of the network on the given figure.
Si1 +20V Vo R 4.7k
Si2
1BH62
Determine Vo and ID.

1BH62

Experiment 2 Wave Shaping Circuits

Uploaded by

Copyright:

Available Formats

Experiment 2 Wave Shaping Circuits

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Experiment 2 Wave Shaping Circuits

Uploaded by

Copyright:

Available Formats

What are the main components used in the clipping and clamping circuits?

What are the main components used in the clipping and clamping circuits?

What is the purpose of the 15KΩ resistor in the clipping circuits?

What is the purpose of the 15KΩ resistor in the clipping circuits?

EXPERIMENT 2: WAVESHAPING CIRCUITS

II. BASIC CONCEPT

IV. WIRING DIAGRAMS

R1 15k D1 1N4001 1 2 XSC1 0 XFG1

Figure 2.1 Positive Clipper

Oscilloscope Function Generator 6V/200Hz

Figure 2.2 Negative Clipper

Oscilloscope Function Generator 6V/200Hz

R1 15k D1 1N4001 4 3 XSC1 5k Key=A R2 50%

Figure 2.3 Positive Biased Clipper

Oscilloscope Function Generator 6V/200Hz

R1 15k D1 1N4001 15 V 5k 3 XFG1 4 1 0 XSC1 2 5k Key=A R2 50%

Figure 2.4 Negative Biased Clipper

Oscilloscope Function Generator 6V/200Hz

1uF D1 1N4001 R1 10k 12 XSC1 XFG1

Figure 2.5 Clamper Circuit

VI. DATA AND RESULTS

VII. SAMPLE COMPUTATIONS

PEDROSO, ELVIN LOUIE R. IX. ANALYSIS OF RESULTS

XI. SELF-TEST QUESTIONS

XII. APPLICATIONS (CIRCUIT SIMULATION)

2. Perform an analysis of the network on the given figure.

Si1 +20V Vo R 4.7k

Determine Vo and ID.

You might also like