1 Input Data: WWW - Hilti.in

www.hilti.in Company: Specifier: Address: Phone I Fax: E-Mail: Specifier's comments: Page: Project: Sub-Project I Pos. No.
: Date:
Profis Anchor 2.3.3

1 05-02-2013
1 Input data
Anchor type and diameter: Effective embedment depth: Material: Evaluation Service Report:: Issued I Valid: Proof: Stand-off installation: Anchor plate: Profile: Base material: Reinforcement: ETA 98/0001 17-06-2011 | 19-02-2013 design method ETAG No. 001 Annex C(2010) eb = 0 mm (no stand-off); t = 12 mm lx x ly x t = 250 mm x 250 mm x 12 mm; (Recommended plate thickness: not calculated) Square hollow; (L x W x T) = 140 mm x 140 mm x 5 mm cracked concrete, C20/25, fcc = 25.00 N/mm2; h = 250 mm no reinforcement or reinforcement spacing >= 150 mm (any ) or >= 100 mm ( <= 10 mm) no longitudinal edge reinforcement Reinforcement to control splitting according to ETAG 001, Annex C, 5.2.2.6 present. Geometry [mm] & Loading [kN, kNm] HST M12 hef = 70 mm, hnom = 95 mm
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.in Company: Specifier: Address: Phone I Fax: E-Mail: Page: Project: Sub-Project I Pos. No.: Date:
Profis Anchor 2.3.3

2 05-02-2013
2 Load case/Resulting anchor forces

Load case: Design loads Anchor reactions [kN] Tension force: (+Tension, -Compression) Anchor Tension force Shear force Shear force x 1 0.000 1.750 1.750 2 0.000 1.750 1.750 3 0.000 1.750 1.750 4 0.000 1.750 1.750 max. concrete compressive strain: 0.07 [] max. concrete compressive stress: 2.16 [N/mm2] resulting tension force in (x/y)=(0/0): 0.000 [kN] resulting compression force in (x/y)=(0/0): 135.000 [kN] Shear force y 0.000 0.000 0.000 0.000 3 y 4
Compression
3 Tension load (ETAG, Annex C, Section 5.2.2)

Steel Strength* Pullout Strength* Concrete Breakout Strength** Splitting failure** * anchor having the highest loading Load [kN] N/A N/A N/A N/A **anchor group (anchors in tension) Capacity [kN] N/A N/A N/A N/A Utilization bN [%] N/A N/A N/A N/A Status N/A N/A N/A N/A
Profis Anchor 2.3.3

3 05-02-2013
4 Shear load (ETAG, Annex C, Section 5.2.3)

Steel Strength (without lever arm)* Steel failure (with lever arm)* Pryout Strength** Concrete edge failure in direction ** * anchor having the highest loading Load [kN] 1.750 N/A 7.000 N/A **anchor group (relevant anchors) Capacity [kN] 28.000 N/A 106.653 N/A Utilization bV [%] 7 N/A 7 N/A Status OK N/A OK N/A
4.1 Steel Strength (without lever arm) VRk,s [kN] 35.000 4.2 Pryout Strength Ac,N [mm2] 152100 ec1,V [mm] 0 N0 [kN] Rk,c 21.084 A0 [mm2] c,N 44100 yec1,N 1.000 gM,c,p 1.500 ccr,N [mm] 105 ec2,V [mm] 0 VRd,c1 [kN] 106.653 scr,N [mm] 210 yec2,N 1.000 VSd [kN] 7.000 k-factor 2.200 ys,N 1.000 yre,N 1.000 gM,s 1.250 VRd,s [kN] 28.000 VSd [kN] 1.750
5 Displacements (highest loaded anchor)

Short term loading: NSk VSk = = 0.000 [kN] 1.296 [kN] dN dV dNV Long term loading: NSk VSk = = 0.000 [kN] 1.296 [kN] dN dV dNV = = = 0.000 [mm] 0.356 [mm] 0.356 [mm] = = = 0.000 [mm] 0.240 [mm] 0.240 [mm]
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not included in this calculation! The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
6 Warnings
To avoid failure of the anchor plate the required thickness can be calculated in PROFIS Anchor. Load re-distributions on the anchors due to elastic deformations of the anchor plate are not considered. The anchor plate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the loading! Checking the transfer of loads into the base material is required in accordance with ETAG 001, Annex C(2010)Section 7! The software considers that the grout is installed under the anchor plate without creating air voids and before application of the loads. The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of ETAG 001, Annex C! For larger diameters of the clearance hole see Chapter 1.1. of ETAG 001, Annex C!
Fastening meets the design criteria!
Profis Anchor 2.3.3

4 05-02-2013
7 Installation data
Anchor plate, steel: Anchor type and diameter: HST, M12 Profile: Square hollow; 140 x 140 x 5 mm Installation torque: 0.060 kNm Hole diameter in the fixture: df = 14 mm Hole diameter in the base material: 12 mm Plate thickness (input): 12 mm Hole depth in the base material: 95 mm Recommended plate thickness: not calculated Minimum thickness of the base material: 140 mm Cleaning: Manual cleaning of the drilled hole according to instructions for use is required. 7.1 Required accessories Drilling Suitable Rotary Hammer Properly sized drill bit Cleaning Manual blow-out pump y Setting Torque wrench Hammer
125
125
35 180 125
2 35
35
180
35
Coordinates Anchor [mm] Anchor 1 2 3 4 x -90 90 -90 90 y -90 -90 90 90 c-x c+x c-y c+y -
125
Profis Anchor 2.3.3

5 05-02-2013
8 Remarks; Your Cooperation Duties

Any and all information and data contained in the Software concern solely the use of Hilti products and are based on the principles, formulas and security regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product. The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior to using them for your specific facility. The Software serves only as an aid to interpret norms and permits without any guarantee as to the absence of errors, the correctness and the relevance of the results or suitability for a specific application. You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular backup of programs and data and, if applicable, carry out the updates of the Software offered by Hilti on a regular basis. If you do not use the AutoUpdate function of the Software, you must ensure that you are using the current and thus up-to-date version of the Software in each case by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or programs, arising from a culpable breach of duty by you.

1 Input Data: WWW - Hilti.in

Uploaded by

Copyright:

Available Formats

1 Input Data: WWW - Hilti.in

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

1 Input Data: WWW - Hilti.in

Uploaded by

Copyright:

Available Formats

www.hilti.in Company: Specifier: Address: Phone I Fax: E-Mail: Specifier's comments: Page: Project: Sub-Project I Pos. No.

Profis Anchor 2.3.3

Profis Anchor 2.3.3

2 Load case/Resulting anchor forces

3 Tension load (ETAG, Annex C, Section 5.2.2)

Profis Anchor 2.3.3

4 Shear load (ETAG, Annex C, Section 5.2.3)

5 Displacements (highest loaded anchor)

Fastening meets the design criteria!

Profis Anchor 2.3.3

Profis Anchor 2.3.3

8 Remarks; Your Cooperation Duties

You might also like