Boss GS-10 Manual

Owners Manual
Thank you, and congratulations on your choice of the BOSS GS-10 Guitar Effects System with USB Audio Interface. Before using this unit, carefully read the sections entitled: USING THE UNIT SAFELY (page 23) IMPORTANT NOTES (page 45) These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owners manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.
Printing Conventions in This Manual

Text or numerals enclosed in square brackets [ ] indicate buttons. [WRITE] WRITE button [USB] USB button Reference such as (p. **) indicate pages in this manual to which you can refer.
Copyright 2003 BOSS CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of BOSS CORPORATION.
USING THE UNIT SAFELY
Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly. Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly. * Material damage refers other adverse effects respect to the home furnishings, as well animals or pets. to damage or caused with and all its to domestic
The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger. The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled. The symbol alerts the user to things that must be carried out. The specific thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
001
009
Before using this unit, make sure to read the instructions below, and the Owners Manual. ..........................................................................................................
002c
Do not open (or modify in any way) the unit or its AC adaptor. ..........................................................................................................
003
Do not excessively twist or bend the power cord, nor place heavy objects on it. Doing so can damage the cord, producing severed elements and short circuits. Damaged cords are fire and shock hazards! ..........................................................................................................
010
Do not attempt to repair the unit, or replace parts within it (except when this manual provides specific instructions directing you to do so). Refer all servicing to your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the Information sheet. ..........................................................................................................
004
Never use or store the unit in places that are: Subject to temperature extremes (e.g., direct sunlight in an enclosed vehicle, near a heating duct, on top of heat-generating equipment); or are Damp (e.g., baths, washrooms, on wet floors); or are Humid; or are Exposed to rain; or are Dusty; or are Subject to high levels of vibration. ..........................................................................................................
007
This unit, either alone or in combination with an amplifier and headphones or speakers, may be capable of producing sound levels that could cause permanent hearing loss. Do not operate for a long period of time at a high volume level, or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should immediately stop using the unit, and consult an audiologist. ..........................................................................................................
011
Do not allow any objects (e.g., flammable material, coins, pins); or liquids of any kind (water, soft drinks, etc.) to penetrate the unit.
..........................................................................................................
012b
Immediately turn the power off, remove the AC adaptor from the outlet, and request servicing by your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the Information sheet when: The AC adaptor, the power-supply cord, or the plug has been damaged; or If smoke or unusual odor occurs Objects have fallen into, or liquid has been spilled onto the unit; or The unit has been exposed to rain (or otherwise has become wet); or The unit does not appear to operate normally or exhibits a marked change in performance. ..........................................................................................................
Make sure you always have the unit placed so it is level and sure to remain stable. Never place it on stands that could wobble, or on inclined surfaces. ..........................................................................................................
008c
Be sure to use only the AC adaptor supplied with the unit. Also, make sure the line voltage at the installation matches the input voltage specified on the AC adaptors body. Other AC adaptors may use a different polarity, or be designed for a different voltage, so their use could result in damage, malfunction, or electric shock. ..........................................................................................................
013
101b
In households with small children, an adult should provide supervision until the child is capable of following all the rules essential for the safe operation of the unit. ..........................................................................................................
014
The unit and the AC adaptor should be located so their location or position does not interfere with their proper ventilation. ..........................................................................................................
102c
Protect the unit from strong impact. (Do not drop it!) ..........................................................................................................
015
Always grasp only the plug on the AC adaptor cord when plugging into, or unplugging from, an outlet or this unit. ..........................................................................................................
103b
Do not force the units power-supply cord to share an outlet with an unreasonable number of other devices. Be especially careful when using extension cordsthe total power used by all devices you have connected to the extension cords outlet must never exceed the power rating (watts/amperes) for the extension cord. Excessive loads can cause the insulation on the cord to heat up and eventually melt through. ..........................................................................................................
016
At regular intervals, you should unplug the AC adaptor and clean it by using a dry cloth to wipe all dust and other accumulations away from its prongs. Also, disconnect the power plug from the power outlet whenever the unit is to remain unused for an extended period of time. Any accumulation of dust between the power plug and the power outlet can result in poor insulation and lead to fire. ..........................................................................................................
104
Before using the unit in a foreign country, consult with your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the Information sheet. ..........................................................................................................
023
Try to prevent cords and cables from becoming entangled. Also, all cords and cables should be placed so they are out of the reach of children. ..........................................................................................................
106
DO NOT play a CD-ROM disc on a conventional audio CD player. The resulting sound may be of a level that could cause permanent hearing loss. Damage to speakers or other system components may result. ..........................................................................................................
Never climb on top of, nor place heavy objects on the unit. ..........................................................................................................
107c
Never handle the AC adaptor or its plugs with wet hands when plugging into, or unplugging from, an outlet or this unit. ..........................................................................................................
108b
Before moving the unit, disconnect the AC adaptor and all cords coming from external devices. ..........................................................................................................
109b
Before cleaning the unit, turn off the power and unplug the AC adaptor from the outlet. ..........................................................................................................
110b
Whenever you suspect the possibility of lightning in your area, disconnect the AC adaptor from the outlet. ..........................................................................................................
IMPORTANT NOTES
291a
In addition to the items listed under USING THE UNIT SAFELY on page 23, please read and observe the following:
Power Supply
301
Repairs and Data

452
Do not use this unit on the same power circuit with any device that will generate line noise (such as an electric motor or variable lighting system).
302
The AC adaptor will begin to generate heat after long hours of consecutive use. This is normal, and is not a cause for concern.
307
Before connecting this unit to other devices, turn off the power to all units. This will help prevent malfunctions and/or damage to speakers or other devices.
Please be aware that all data contained in the units memory may be lost when the unit is sent for repairs. Important data should always be backed up in another MIDI device (e.g., a sequencer), computer, or written down on paper (when possible). During repairs, due care is taken to avoid the loss of data. However, in certain cases (such as when circuitry related to memory itself is out of order), we regret that it may not be possible to restore the data, and Roland assumes no liability concerning such loss of data.
Placement
351
Memory Backup
501b
Using the unit near power amplifiers (or other equipment containing large power transformers) may induce hum. To alleviate the problem, change the orientation of this unit; or move it farther away from the source of interference.
352a
This device may interfere with radio and television reception. Do not use this device in the vicinity of such receivers.
352b
This unit contains a battery which powers the units memory circuits while the main power is off. When this battery becomes weak, the message shown below will appear in the display. Once you see this message, have the battery replaced with a fresh one as soon as possible to avoid the loss of all data in memory. To have the battery replaced, consult with your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the Information sheet. Battery Low !! Please Change
Noise may be produced if wireless communications devices, such as cell phones, are operated in the vicinity of this unit. Such noise could occur when receiving or initiating a call, or while conversing. Should you experience such problems, you should relocate such wireless devices so they are at a greater distance from this unit, or switch them off.
354a
Additional Precautions
551
Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Excessive heat can deform or discolor the unit.
355b
Please be aware that the contents of memory can be irretrievably lost as a result of a malfunction, or the improper operation of the unit. To protect yourself against the risk of loosing important data, we recommend that you periodically save a backup copy of important data you have stored in the units memory in another MIDI device (e.g., a sequencer), or computer.
552
When moved from one location to another where the temperature and/or humidity is very different, water droplets (condensation) may form inside the unit. Damage or malfunction may result if you attempt to use the unit in this condition. Therefore, before using the unit, you must allow it to stand for several hours, until the condensation has completely evaporated.
Unfortunately, it may be impossible to restore the contents of data that was stored in another MIDI device (e.g., a sequencer), or computer once it has been lost. Roland Corporation assumes no liability concerning such loss of data.
553
Maintenance
401a
Use a reasonable amount of care when using the units buttons, sliders, or other controls; and when using its jacks and connectors. Rough handling can lead to malfunctions.
554
Never strike or apply strong pressure to the display.

556
For everyday cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water. To remove stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth.
402
When connecting / disconnecting all cables, grasp the connector itselfnever pull on the cable. This way you will avoid causing shorts, or damage to the cables internal elements.
558a
Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation.
To avoid disturbing your neighbors, try to keep the units volume at reasonable levels. You may prefer to use headphones, so you do not need to be concerned about those around you (especially when it is late at night).
IMPORTANT NOTES
559a
When you need to transport the unit, package it in the box (including padding) that it came in, if possible. Otherwise, you will need to use equivalent packaging materials.
561
Copyright
851
Use only the specified expression pedal (EV-5; sold separately). By connecting any other expression pedals, you risk causing malfunction and/or damage to the unit.
562
Unauthorized recording, distribution, sale, lending, public performance, broadcasting, or the like, in whole or in part, of a work (musical composition, video, broadcast, public performance, or the like) whose copyright is held by a third party is prohibited by law.
852a
Use a cable from Roland to make the connection. If using some other make of connection cable, please note the following precautions. Some connection cables contain resistors. Do not use cables that incorporate resistors for connecting to this unit. The use of such cables can cause the sound level to be extremely low, or impossible to hear. For information on cable specifications, contact the manufacturer of the cable.
Handling CD-ROMs
563
When exchanging audio signals through a digital connection with an external instrument, this unit can perform recording without being subject to the restrictions of the Serial Copy Management System (SCMS). This is because the unit is intended solely for musical production, and is designed not to be subject to restrictions as long as it is used to record works (such as your own compositions) that do not infringe on the copyrights of others. (SCMS is a feature that prohibits second-generation and later copying through a digital connection. It is built into MD recorders and other consumer digital-audio equipment as a copyright-protection feature.)
853
Unauthorized duplication, reproduction, hiring, and lending prohibited.

564
Before you open the included CD-ROM, you must read the license agreement. Opening the CD-ROM will be taken to mean your acceptance of the license agreement.
801
Do not use this unit for purposes that could infringe on a copyright held by a third party. We assume no responsibility whatsoever with regard to any infringements of third-party copyrights arising through your use of this unit.
Avoid touching or scratching the shiny underside (encoded surface) of the disc. Damaged or dirty CD-ROM discs may not be read properly. Keep your discs clean using a commercially available CD cleaner.
962b
In the interest of product improvement, the specifications and/or contents of this package are subject to change without prior notice. DO NOT play a CD-ROM disc on a conventional audio CD player. The resulting sound may be of a level that could cause permanent hearing loss. Damage to speakers or other system components may result.
204
* Microsoft and Windows are registered trademarks of Microsoft Corporation.

206e
* Screen shots in this documents are reprinted with permission from Microsoft Corporation.
206j
* Windows is known officially as: Microsoft Windows operating system.

207
* Apple and Macintosh are registered trademark of Apple Computer, Inc.

209
* MacOS is a trademark of Apple Computer, Inc.

220
* All product names mentioned in this document are trademarks or registered trademarks of their respective owners.
231
* OMS is a registered trademark of Opcode Systems, Inc.

232
* FreeMIDI is a trademark of Mark of the Unicorn, Inc.
Contents
USING THE UNIT SAFELY ...................2 IMPORTANT NOTES ..........................4 Main Features ..................................9 Chapter 3 Saving the Tones You Have Created ..... 25
Storing Patches (PATCH WRITE)...............................25 Copying Patches .............................................................25 Exchanging Patches........................................................26 Initializing Patches ........................................................26 Registering Your Favorite Patches (DIRECT PATCH)..........................................................27 Copying the PREAMP/SPEAKER Settings to Another Channel........................................................27
Panel Descriptions ..........................10

Front Panel.......................................................................10 Rear Panel ........................................................................12 Signal Flow......................................................................13
Chapter 1 Playing Sounds ..............................14

Making the Connections...............................................14 Turning On the Power ..................................................15 Turning Off the Power..............................................15 Using the GS-10s Speakers .........................................15 Adjusting the Output Level .........................................15 Setting Output Device (Amps) (OUTPUT SELECT) .......................................................16 Connecting Audio Devices to the AUX INPUT Jack.....................17 Using the Digital Output..............................................17
Chapter 4 Introduction to Effects and Parameters .... 28

PREAMP/SPEAKER (Preamp/Speaker Simulator)........................................28 COMP (Compressor) .....................................................31 OD/DS (Overdrive/Distortion)....................................32 DELAY..............................................................................33 CHORUS..........................................................................34 REVERB ...........................................................................34 EQ (Equalizer).................................................................35 FX-1....................................................................................36 PW (Pedal Wah).........................................................36 AW (Auto Wah) .........................................................36 TM (Tone Modify) .....................................................37 ACS (Advanced Compressor)..................................38 LM (Limiter) ...............................................................38 ENH (Enhancer).........................................................39 SG (Slow Gear) ...........................................................39 TR (Tremolo) ..............................................................39 DF (Defretter) .............................................................40 RM (Ring Modulator)................................................40 FB (Feedbacker)..........................................................40 FX-2....................................................................................41 PH (Phaser).................................................................42 FL (Flanger) ................................................................42 HR (Harmonist) .........................................................43 PS (Pitch Shifter) ........................................................44 OC (Octave) ................................................................45 PB (Pedal Bend)..........................................................45 2CE (2x2 Chorus) .......................................................45 PAN .............................................................................46
Chapter 2 Creating Your Own Favorite Tones (Patches) ........................................18

What is a Patch? ..............................................................18 How to Select Patches (Patch Change).......................18 About the Display Indication ..................................18 If the Patch Does Not Switch ...................................18 Selecting the Input (INPUT SELECT)........................19 Setting the Mic Input Level (MIC GAIN) ..............20 Adjusting the Tones with the Knobs .........................21 Turning the Effect On and Off ....................................22 Setting the Effects Simply (QUICK FX) ....................22 Making More Precise Effect Settings .........................23 Naming Patches ..............................................................24 Changing the Connection Order of Effects (Effect Chain) ..................................................................24
Contents
VB (Vibrato)................................................................46 UV (Uni-V) .................................................................47 RT (Rotary) .................................................................47 SDD (Short Delay) .....................................................48 HU (Humanizer)........................................................48 SL (Slicer) ....................................................................49 AR (Auto Riff) ............................................................49 SYN (Guitar Synth) ...................................................50 BS (Bass Simulator) ...................................................52 SEQ (Stereo Equalizer)..............................................52 NAME/NS/MASTER .....................................................53 Name (Patch Name) ..................................................53 Noise Suppressor.......................................................53 Master..........................................................................54 Foot Volume ...............................................................54 Effect Chain ................................................................54
Chapter 7 Convenient Functions and System Settings ... 64

Tuning the Guitar ..........................................................64 Turning the Tuner Function On ..............................64 About the Display During Tuning..........................64 How to Tune...............................................................64 Changing the Tuner Settings ...................................64 Adjusting the Display Contrast (LCD Contrast) ................................................................65 Limiting the Patches That Can Be Switched (Patch Extent) .........................65 Keeping the Same Pedal Operations When Switching Patches (Assign Hold)....................66 Setting the Knob Functions (Knob Mode) ................66 Checking the Effect Output Level with the Level Meter......................................................67
Chapter 5 Creating Original Effects Types (Customize) ..55

Customizing the COSM Amps....................................55 Customizing the Speakers............................................56 Customizing Overdrive and Distortion.....................56 Customizing Pedal Wah ...............................................57
Chapter 8 Using the GS-10 with External MIDI Devices Connected .... 68
Operations Using MIDI ................................................68 Operating From the GS-10........................................68 Remotely Controlling the GS-10 Using an External MIDI Device...............................68 Making the Settings for MIDI Functions ..................69 Transmitting and Receiving Settings Data ...............71 Transmitting Data to an External MIDI Device (Bulk Dump) .............71 Receiving Data from an External MIDI Device (Bulk Load)...........72 Setting the Program Change Map...............................73
Enabling/Disabling the Program Change Map Settings (MIDI Map Select) .......74
Chapter 6 Setting the External Pedal Functions .....58

Setting the External Expression Pedal Functions (Expression Pedal Function) ..............................................58
Setting the External Foot Switch Functions (Control 1, 2 Function)...................................................59 Setting the External Pedal Function for Individual Patches (Assign)...................................60 Quick Settings ............................................................60 Manual Settings .........................................................61
Changing Patch Numbers on an External MIDI Device From the GS-10 ...........74
Controlling Recorders and Sequencers Remotely from the GS-10 (Remote Control) .....................................75
Setting the Messages Used for Controlling Devices...................................75 Controlling the Device Remotely ............................76
Contents
Chapter 9 Using the GS-10 Connected to a Computer Via USB .......78

Before Connecting with USB.......................................78 Driver Mode ...............................................................78 Setting USB-Related Functions ...................................78 Adjusting the Recording Level (Output Level)............................................................78 Adjusting the Playback Volume Level (Input Level)...............................................................78 Enabling and Disabling the Direct Monitor Command .................................79 Switching the Output Signals (Direct Monitor) .........................................................79 Setting the Output Mode..........................................79 Switching the Driver Mode......................................80 Recording the GS-10s Output with a Computer.............................................................81 Applying Effects with the GS-10 to a Computers Audio Playback.................................81 Running the GS-10 from a Computer ........................81 Using the GS-10 As a MIDI Interface ........................81
Installing & Setup the USB Driver ...................... 91

Installing & Setting Up the Driver (Windows) ...............................92 Installing & Setting Up the Driver (Macintosh) ...........................112 Setting the Special Drivers Functions.....................128
Troubleshooting ........................... 130

Problems when using the GS-10 ...............................130 Problems with the sound........................................130 Other Problems ........................................................131 Problems related to the USB driver ..........................131 Problems when using the USB driver ......................133 Deleting the special driver .........................................139
Index ........................................... 140
Appendices ....................................82
About MIDI.....................................................................82 How MIDI messages are transmitted and received ...............................................................82 Main types of MIDI message used by the GS-10 ......................................................82 About the MIDI implementation ............................83 About USB.......................................................................83 Error Messages................................................................83 Patch List..........................................................................84 Restoring the Factory Settings (Factory Reset).................................................................86 Factory Settings..........................................................86 MIDI Implementation Chart .......................................87 Specifications..................................................................88
Main Features
True Tabletop Guitar Effects System
This is an all-new guitar effects system, which gives you not only the kind of professional-quality effects available only from BOSS, but features a USB interface and built-in monitor speakers as well.
Internal Effects Derived from the GT-6/GT-6B, Made More Powerful

All components of the GT-6 and GT-6B COSM amps and effects, famous for their sonic quality and ease of use, have been thoroughly improved in this system. With its new amp types and effects, the GS-10 takes you to a new dimension in sound creation.
The Functions You Want for Digital Recording

The GS-10 not only gives you the recording capabilities you would expect with its DIGITAL OUT (coaxial) connector, it also allows you to record simply and easily via USB. Whats more, you can also record the direct sound while listening to the performance as it sounds with the effects added, and add effects to sounds that have already been recorded.
Accepts Multiple Inputs

You can use the GS-10 not just with your guitar, but as an audio interface for input of sounds from bass guitars, mics, and external stereo equipment. The GS-10 also includes amp types and effects for basses, giving you total song-creation capabilities all in one single device.
Stereo Monitor Speakers Built-In

The GS-10 comes with its own monitor speakers, so you can enjoy creating and performing music all with one unit.
GS-10 Editor and GS-10 Librarian Included

In addition to intuitive knob controls, the GS-10 also includes the Editor software for use in creating sounds and Librarian software for managing the tones you have created. These softwares let you perform the procedures for creating sounds and changing effect connection sequences easily from your computer screen.
WDM/ASIO-Compatible USB Driver

The GS-10 comes with a GS-10-exclusive driver for stable, high-quality recording and playback. Now enjoy high-quality audio recordings with 24-bit and ASIO applications.
COSM (Composite Object Sound Modeling)

Composite Object Sound Modeling (COSM) is Rolands innovative and powerful sound modeling technology. COSM analyzes the many factors that make up the original sound, such as the electrical and physical characteristics of the original, and then produces a digital model that can reproduce the same sound.
Panel Descriptions
Front Panel
fig.00-041
21
1 2 15 16 3 4 8 9 27
1. Display
A variety of information about the GS-10 appears here. Normally, patch names are displayed.
19 20 22 24 23 26 25 10 11 17 18 12 13 14 28
3. COMP (Compressor) (p. 21, p. 31)

SUSTAIN Knob
Adjusts the compressors sustain effect (an effect that keeps the sound playing).
2. PREAMP/SPEAKER (p. 21, p. 28) (Preamp/Speaker Simulator)

GAIN Knob
Adjusts the degree of preamp distortion.
COMP On/Off Button

Press to change the settings.
BASS Knob
Adjusts the sound quality of the preamps lowfrequency range.
4. OD/DS (p. 21, p. 32) (Overdrive/Distortion)

DRIVE Knob
Adjusts the degree of overdrive or distortion.
MIDDLE Knob
Adjusts the sound quality of the preamps midrange.
LEVEL Knob
Adjusts the overdrive/distortion volume level.
TREBLE Knob
Adjusts the sound quality of the preamps highfrequency range.
OD/DS On/Off Button

PRESENCE Knob
Adjusts the sound quality in the preamps ultra-highfrequency range.
5. DELAY (p. 21, p. 33)

FEEDBACK Knob
Adjusts the number of times the delay is repeated.
LEVEL Knob
Adjusts the preamp volume level.
LEVEL Knob
Adjusts the volume level of the delay sound.
PREAMP/SPEAKER On/Off Button

DELAY On/Off Button

CHANNEL SELECT Button

Switches the preamp channel.
10
Panel Descriptions
TAP Button
Use this when setting the delay time with the tap input. (p. 33)
17. EXIT Button

Use this to undo operations.
18. WRITE Button

Press to store settings.
6. CHORUS (p. 21, p. 34)

LEVEL Knob
Adjusts the volume level of the chorus sound.
19. AUX INPUT LEVEL Knob

Adjusts the volume of the input from the AUX INPUT jack. * Setting the input level too high may result in oscillation.
CHORUS On/Off Button

7. REVERB (p. 21, p. 34)

LEVEL Knob
Adjusts the volume level of the reverb sound.
20. OUTPUT LEVEL Knob

Adjusts the GS-10s output level and the units speaker volume.
REVERB On/Off Button

21. USB Button (p. 78)

Used when making USB-related settings. The indicator lights when the GS-10 is connected to your computer.
8. FX-1 (p. 36)

FX-1 On/Off Button
22. SPEAKER ON/OFF Button (p. 15)

Switches the GS-10s speakers on and off.
9. FX-2 (p. 41)

FX-2 On/Off Button
23. METER Button (p. 67)

Press to use the meter function.
24. SYSTEM Button

Use for making settings for the GS-10s overall operating environment.
10. EQ (Equalizer) (p. 35)

EQ On/Off Button
Press when changing the settings.
25. TUNER Button (p. 64)

Press to use the tuner function.
11. NAME/NS/MASTER Button (p. 24, p. 53)

Use for naming patches (NAME), setting the noise suppressor (NS), and making the master settings (MASTER).
26. DIRECT PATCH Button (p. 18)

Allows you to directly call up your favorite patches registered in the GS-10.
12. ASSIGN Button (p. 60)

Use this to make settings for the expression pedal and control pedal.
27. PHONES Jack

Connect the stereo headphones here.
28. GUITAR/BASS Jack

The guitar or bass is connected here.
13. INPUT SELECT Button

Selects the input signal to which the effect is applied.
14. QUICK FX Button (p. 22)

Using the Quick Settings lets you complete the settings procedure quickly and easily.
15. PATCH/VALUE Dial

Use this when switching patches and changing the values of settings.
16. PARAMETER Buttons

Press to select parameters. * To jump to the main parameters, hold down one of these buttons while you press the other. With items for which there arent that many parameters, the GS-10 jumps to the last (or initial) parameter.
11
Panel Descriptions
Rear Panel
fig.00-042
10
12
1. MIC INPUT Jack/Connector
9
12. Security Slot (
11
Input jack/connector for use with mics. Both standard TRS type and XLR type are provided. * Use only one of these jacks at a time. * Not compatible with phantom power.
http://www.kensington.com/
2. AUX INPUT Jacks L/R

Used for connecting a CD player or similar audio device, rhythm machine, sound module, or similar devices.
3. OUTPUT Jacks L/R

Used for connecting to an audio set, recorder, mixer, or similar equipment.
4. GUITAR AMP OUT Jack

Connect your guitar amp here.
5. EXP PEDAL/CTL 1,2

(Expression Pedal/Control Pedal 1,2) Jack
Connect an optional expression pedal (such as the EV5) or foot switch (such as the FS-5U) here.
6. DIGITAL OUT Connector

Outputs digital audio signals.
7. USB Connector
Use a USB cable to connect this connector to your computer to exchange data between the GS-10 and the computer.
8. MIDI IN/OUT Connector

Connect an external MIDI device to these connectors to transmit and receive MIDI messages
9. POWER switch
Turns the power on and off.
10. AC Adaptor Jack

Connect the included AC adaptor (BRC series) here.
11. Cord Hook

Hook the AC adaptor cord here to prevent the adaptor plug from being disconnected.
12
Panel Descriptions
Signal Flow
fig.00-043
Computer
CONTROL IN
CONTROL OUT
GS-10 OUT
Recorder etc.
MIDI OUT
GS-10 IN
MIDI IN
USB
DIGITAL OUT
Expression Pedal
MIDI OUT
MIDI SELECT
Foot Switch
Sound Module Sequencer
MIDI IN
EXP/CTL 1, 2
Guitar/Bass
CONTROL
GUITAR/ BASS PHONES MIC INPUT
Speaker Headphones
Mic
INPUT SELECT A/D MULTI EFFECTS D/A
GUITAR AMP OUT OUTPUT
Guitar Amp
AUX INPUT
CD/MD
Mixer etc.
Audio signal Control or MIDI signal
13
Chapter 1 Playing Sounds

Making the Connections
fig.01-010
Mic
or Computer
AC Adaptor (BRC series)
Guitar or Bass Guitar Amp Stereo Headphones Foot Switch (FS-5U, etc.) Expression Pedal (Roland EV-5, etc.)
Mixer
* To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. * Turn up guitar amp and audio amp volume levels and the GS10s OUTPUT LEVEL only after turning on the power to all connected devices. To prevent the inadvertent disruption of power to your unit (should the plug be pulled out accidentally), and to avoid applying undue stress to the AC adaptor jack, anchor the power cord using the cord hook, as shown in the illustration.
This instrument is equipped with balanced (XLR/TRS) type MIC INPUT jacks. Wiring diagrams for these jacks are shown below. Make connections after first checking the wiring diagrams of other mic you intend to connect.
fig.01-021
* Not compatible with phantom power. Howling could be produced depending on the location of mics relative to speakers. This can be remedied by: 1. 2. 3. Changing the orientation of the mic(s). Relocating mic(s) at a greater distance from speakers. Lowering volume levels.
fig.01-020
14
When using the unit with an expression pedal connected to the EXP PEDAL/CTL 1,2 jack, set Minimum Volume to the MIN position. Use only the specified expression pedal (Roland EV-5; optional). By connecting any other expression pedals, you risk causing malfunction and/or damage to the unit. When using the unit with a foot switch (FS-5U; optional) connected to the EXP PEDAL/CTL 1,2 jack, set the polarity switch as shown below.
Polarity Switch
* Upon power-up, the patch most recently selected when the power was last turned off is selected. * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. 3. Next, turn on the power to guitar amp and audio devices.
Section 1
fig.01-030
Turning Off the Power

1. Before turning off the power, confirm the following. Is the volume on the GS-10, your amp, and all other connected devices turned down to the minimum level? 2. Turn off the power to guitar amp and audio devices.
* You can use the special (optional Roland) PCS-31 connector cord to connect two foot switches.
fig.01-040
3. Turn the GS-10s power off.
PCS-31
Using the GS-10s Speakers

Press [SPEAKER ON/OFF], causing the indicator to light.
fig.01-050
White
Red
When using the unit with a foot switch (the optional FS5U) connected to the EXP PEDAL/CTL 1,2 jack, make the settings given on p. 59.
Turning On the Power

Once the connections have been completed, turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. 1. Before turning on the power, confirm the following. Are all external devices properly connected? Is the volume on the GS-10, your amp, and all other connected devices turned down to the minimum level? 2. Switch ON the POWER switch on the GS-10s rear panel. A few seconds later, the unit enters the ordinary performance mode. The screen that appears at this point is called the Play screen.
fig.01-050d
* When not using the GS-10s speakers, press [SPEAKER ON/ OFF], so the indicator is off.
Adjusting the Output Level

Adjust the GS-10s output level and speaker volume with the OUTPUT LEVEL knob.
fig.01-060
15
Setting Output Device (Amps) (OUTPUT SELECT)

Select the type of output device connected to the OUTPUT jack or GUITAR AMP OUT jack.
Combo Return
Use this setting when connecting to RETURN with a combo amp.
Stack Return
Use this setting when connecting to RETURN of a stack amp or rack mounted power amp. 3. Press [EXIT] to return to the Play screen. * Set OUTPUT SELECT as shown below, when the PREAMP/ SPEAKER type (p. 29) is set to CONCERT 810, SESSION, BASS 360, T.E., B-MAN, FLIP TOP, Bass Clean, Bass Crunch, Bass HiGain, or Mic Preamp. When connecting to an audio amp or similar equipment: Line/Phones When connecting to a guitar amp: Combo Amp or Combo Return When connecting to a bass amp: Stack Amp or Stack Return
To derive the maximum performance from the GS-10, be sure to make the correct setting for OUTPUT SELECT, the one thats most suitable for your setup.
fig.01-061
Guitar Tuning
You can use the GS-10s built-in tuner function to tune your guitar. For instructions on using this function, refer to Tuning the Guitar (p. 64).
1. Press [SYSTEM], causing the indicator to light. The Output Select settings screen appears.
fig.01-070d
2. Turn the PATCH/VALUE dial to select the type of device connected to the OUTPUT jack or GUITAR AMP OUT jack.
Line/Phones
Set this when connecting the OUTPUT jack to an audio set or when connecting a recorder for recording. Use this setting also when using the GS-10s speakers or headphones.
Combo AMP
Use this setting when connecting to the guitar input of a combo amp (where the amp and speaker or speakers are combined in a single unit).
Stack AMP
Use this setting when connecting to the guitar input of a stack-type guitar amp (where the amp and speaker or speakers are separated).
16
Connecting Audio Devices to the AUX INPUT Jack

When using a CD or MD player, rhythm machine, or similar device for practice, connect these device to the AUX INPUT jack on the rear panel.
fig.01-080
Using the Digital Output

Digital signals are output from the DIGITAL OUT connector on the rear panel. You can connect this directly to the digital in connector of a digital recorder or other device and record with no degradation in sound quality.
fig.01-100
Section 1
DIGITAL IN
CD/MD Player Rhythm Machine Digital Recorder
Use the AUX INPUT knob on the front panel to adjust the input volume level for AUX INPUT. * Setting the input level too high may result in oscillation.
fig.01-090
The input sounds from the AUX INPUT jack are mixed with the guitar sounds within the GS-10, making this a convenient feature when using the GS-10s speakers or headphones. * The mixed sound is not output from DIGITAL OUT.
AUX INPUT
You can set INPUT SELECT and use USB to record the input sounds from the AUX INPUT jack to your computer, and record to a recorder using DIGITAL OUT. You can also add effects to the sounds input from the AUX INPUT jack. For instructions on setting INPUT SELECT, refer to Selecting the Input (INPUT SELECT) (p. 19).
17
Chapter 2 Creating Your Own Favorite Tones (Patches)

What is a Patch?
The GS-10 can store 200 combinations (or sets) of effects and parameter settings. Each of these sets is called a patch. Patches include both User patches and Preset patches.
fig.02-010
How to Select Patches (Patch Change)

When the Play screen is showing in the display, you can switch patches using the PATCH/VALUE dial or DIRECT PATCH [1][4] (p. 27).
fig.02-040
U100
P200
Patch Name Input Select U003 Effects U002 Assign 18 U001 Master Noise Suppressor Patch Name Select InputEffect Chain Effects Assign 18 Master Noise Suppressor Effect Chain User Patches
Patch Name Input Select P103 Effects P102 Assign 18 P101 Master Noise Suppressor Patch Name Select InputEffect Chain Effects Assign 18 Master Noise Suppressor Effect Chain Preset Patches
* If you want to set a limit to the number of patches that can be selected with the PATCH/VALUE dial, change the system function settings (p. 65). * Settings currently being edited are cleared when you switch patches. If you want to save the setting changes youve made, use the Write procedure (p. 25).
User Patches (U001U100)

Newly created effects settings are saved in the User patches. * A U appears in the display when a User patch is being used.
fig.02-020d
About the Display Indication

The following information appears in the Play screen.
fig.02-050d
Patch Name
Preset Patches (P101P200)

The Preset patches contain effect settings that really help bring out the special characteristics of the GS-10. Although you cannot overwrite the Preset patches with your own settings, you can change (edit) a Preset patchs settings, then save the result as a User patch. (p. 25) * A p appears in the display when a Preset patch is being used.
fig.02-030d
User/Preset
Number
If the Patch Does Not Switch

On the GS-10, you cannot switch patches in any screen other than the Play screen. Press [EXIT] to return to the Play screen (p. 15).
18
Selecting the Input (INPUT SELECT)

This selects the input signal to which the effects are added. This is also used for setting the type of device connected to the input connector.
Bass:
You can add effects to the signals input from the GUITAR/BASS jack (when a bass is connected). Signals from MIC INPUT are disregarded, and the signals input to the GS-10 from the USB or AUX INPUT connectors are mixed with the effect output.
Section 2
fig.02-080
To derive the maximum performance from the GS-10, be sure to make the correct setting for INPUT SELECT, the one thats most suitable for your setup. You may not be able to achieve the expected effect if this is not set correctly.
DIGITAL OUT GUITAR/ BASS MIC INPUT AUX INPUT

A/D
USB L OUTPUT
MULTI EFFECTS
R
D/A
GUITAR AMP OUT PHONES
fig.02-051
* Depending on the type of bass guitar you are using, you may not be able to achieve the intended effect if the input level to the GS-10 is excessively high. In such cases, lower the volume or tone of your bass guitar.
Microphone:
You can add effects to the signals input from the MIC INPUT connector. Signals from GUITAR/BASS jack are disregarded, and the signals input to the GS-10 from the USB or AUX INPUT connectors are mixed with the effect output.
fig.02-090
1
1. Press [INPUT SELECT]. The Input Select settings screen appears.
fig.02-060d

A/D
USB L OUTPUT
MULTI EFFECTS
R
D/A
* After setting INPUT SELECT to Microphone, you can press PARAMETER [ ] to set the mic gain (p. 20). 2. Turn the PATCH/VALUE dial to change the settings.
USB (Gtr/Mic):
You can add effects to the signals input from the USB connector (for sounds in the guitar and vocal registers). Signals from GUITAR/BASS and MIC INPUT are disregarded, and the signals input to the GS-10 from the AUX INPUT connector are mixed with the effect output.
fig.02-100
Guitar:
You can add effects to the signals input from the GUITAR/BASS INPUT connector (when a guitar is connected). Signals from MIC INPUT are disregarded, and the signals input to the GS-10 from the USB or AUX INPUT connectors are mixed with the effect output.
fig.02-070
USB DIGITAL OUT USB L OUTPUT

A/D MULTI EFFECTS
DIGITAL OUT L OUTPUT R

D/A
GUITAR/ BASS MIC INPUT AUX INPUT

D/A
MULTI EFFECTS
AUX INPUT
* After setting INPUT SELECT to USB (Gtr/Mic), you can press PARAMETER [ ] to set the USB input level (p. 78).
19
USB (Bass):
You can add effects to the signals input from the USB connector (for sounds in the bass and similar registers). Signals from GUITAR/BASS INPUT and MIC INPUT are disregarded, and the signals input to the GS-10 from the AUX INPUT connector are mixed with the effect output.
fig.02-110
Setting the Mic Input Level (MIC GAIN)

This sets the mic input level when INPUT SELECT is set to Microphone. * The mic gain setting is a global setting used by all patches. 1. Press PARAMETER [ ].
DIGITAL USB OUT L OUTPUT

MULTI EFFECTS
The MIC GAIN settings screen appears in the display.

fig.02-130d
R
D/A
AUX INPUT
2. Adjust the gain by turning the PATCH/VALUE dial while picking up sounds with the mic. Adjust the level so that the level meter does not fluctuate beyond the maximum allowable level.
fig.02-140d
* After setting INPUT SELECT to USB (Bass), you can press PARAMETER [ ] to set the USB input level (p. 78).
AUX:
This setting is used when selecting the input signal from the AUX INPUT connector. Signals input from the GUITAR/BASS INPUT and MIC INPUT are disregarded, and the signals input to the GS-10 via USB are mixed with the effect output.
fig.02-120
* Set the volume for the sound being miked (acoustic guitar, vocals, etc.) to the level to be used in performance. * Setting the mic gain too high may result in oscillation.

A/D
USB L OUTPUT
MULTI EFFECTS
3. Press [EXIT] to return to the Play screen.
R
D/A
20
Adjusting the Tones with the Knobs

The GS-10 panel features 13 knobs for adjusting effect tones. You can use these knobs to make slight adjustments to tones in the selected patch quickly and easily.
fig.02-150
OD/DS (Overdrive/Distortion) DRIVE

Adjusts the degree of overdrive or distortion. The distortion appears stronger as the knob is turned to the right.
OD/DS (Overdrive/Distortion) LEVEL:

Adjusts the overdrive/distortion volume level. The volume increases as the knob is turned to the right.
Section 2
DELAY FEEDBACK:
Adjusts the number of times the delay is repeated. The number of repeats increases as the knob is turned to the right.
DELAY LEVEL:
Adjusts the volume level of the delay sound. The delay sound increases as the knob is turned to the right.
CHORUS LEVEL:
Adjusts the volume level of the chorus sound. The chorus sound increases as the knob is turned to the right.
REVERB LEVEL: PREAMP GAIN:

Adjusts the degree of preamp distortion. The distortion gets stronger as the knob is turned to the right. Adjusts the volume level of the reverb sound. The reverb sound increases as the knob is turned to the right.
PREAMP BASS:
Adjusts the sound quality of the preamps low-frequency range. The low frequencies are boosted as the knob is turned to the right.
PREAMP MIDDLE:
Adjusts the sound quality of the preamps midrange. The midrange frequencies are boosted as the knob is turned to the right.
PREAMP TREBLE:
Adjusts the sound quality of the preamps high-frequency range. The high frequencies are boosted as the knob is turned to the right.
PREAMP PRESENCE:
Adjusts the sound quality in the preamps ultra-highfrequency range. The ultra-high frequencies are boosted as the knob is turned to the right.
PREAMP LEVEL:
Adjusts the preamp volume level. The volume increases as the knob is turned to the right.
COMP (Compressor) SUSTAIN:

Adjusts the compressors sustain effect (an effect that keeps the sound playing). The effect is strengthened as the knob is turned to the right.
21
Turning the Effect On and Off

The GS-10s internal effects are switched on and off with button controls. The indicator for an effects ON/OFF button lights up when the effect is enabled.
fig.02-160
Setting the Effects Simply (QUICK FX)

Each effect includes prepared sample settings called Quick Settings. You can easily create new effect sounds just by selecting and combining these Quick Settings.
fig.02-171
1,2,3
4 2
1. Press [QUICK FX]. The effects selection screen appears in the display.
fig.02-180d
1. Press the ON/OFF button for the effect you want to be able to switch on and off. The settings for the selected effect appear in the display. * With FX-1 and FX-2, the settings for the currently selected effect are shown.
fig.02-170d
1 5
* Performing Step 1 while editing an effect takes you to the status following Step 2. 2. Press the ON/OFF button again to switch the effect on or off. * The effect name flashes in the display when that effect is disabled. 3. To select another effect to be switched on and off, repeat Steps 1 and 2. 4. Press [EXIT] to return to the Play screen. * If you want to save a tone with the settings youve made, use the Write procedure (p. 25) to save the tone to a User patch. * The following appears in the display immediately after patches are changed or when the settings in Quick settings are changed by editing the parameters.
fig.02-200d
2. Press the ON/OFF button for the effect you want to select for Quick Settings. The name of the effect being set with Quick Settings appears in the upper row of the display, and the Quick Settings Name currently selected for that effect appears in the lower row of the display.
fig.02-190d
* The upper row of the display flashes when the selected effect is switched off. Even when using the Quick Settings, you can switch effects on and off with the effect ON/OFF buttons.
22
3. Rotate the VALUE dial to select the Quick Setting you want. The tone switches to that of the selected sample settings. * You can select : User Setting to return the settings to their condition prior to selecting the Quick Settings. 4. To select Quick Settings for another effect, repeat Steps 2 and 3. * Even after performing this procedure, the settings selected in Step 3 are maintained as is and carried over to the Quick Settings for the next effect. 5. Press [EXIT] to return to the Play screen. * If you want to save a tone with the settings youve made, use the Write procedure (p. 25) to save the tone to a User patch.
Making More Precise Effect Settings

Each effect comprises several different kinds of parameters. You can more precisely create the sounds you want by editing each of these parameters individually.
fig.02-210
Section 2
1 6
1. Press the on/off button for the effect with the settings you want to change. The parameters for the selected effect appear in the display. 2. Press PARAMETER [ ][ ] to select the parameter whose settings are to be changed. When more than one parameter is shown in the display, press PARAMETER [ the parameter to be set. ][ ] to move the cursor to
You can jump to the core parameters by pressing PARAMETER [ ] (or [ ]) while holding down PARAMETER [ ] (or [ ]). With items for which there arent that many parameters, the GS-10 jumps to the last (or first) parameter. 3. Rotate the VALUE dial to change the value of a setting. 4. Repeat Steps 2 and 3 for any other parameter settings you want to change. 5. If you further want to change parameter settings in any other effects, repeat Steps 1 through 4. 6. Press [EXIT] to return to the Play screen. * If you want to save a tone with the settings youve made, use the Write procedure (p. 25) to save the tone to a User patch.
23
Naming Patches
Each patch can be given a name (Patch Name) consisting of up to sixteen characters. Youll probably want to take advantage of this feature by assigning names that suggest the sound youll obtain, or the song in which itll be used.
fig.02-220
Changing the Connection Order of Effects (Effect Chain)

Heres how you can change the order in which the effects are connected.
fig.02-240
1. Press [NAME/NS/MASTER] so that the Name edit screen appears in the display. * With each press of [NAME/NS/MASTER], you move to the next item that can be set, in this order: Name Noise Suppressor Master Foot Volume Effect Chain.
fig.02-230d
1. Press [NAME/NS/MASTER] until Effect Chain appears in the display. * With each press of [NAME/NS/MASTER], you move to the next item that can be set, in this order: Name Noise Suppressor Master Foot Volume Effect Chain.
fig.02-250d
2. Press PARAMETER [ ][ the text area you want to edit.
] to move the cursor to
* Effects are shown in lowercase letters when turned off. 2. Use the PATCH/VALUE dial or PARAMETER [ ] [ ] to move the cursor to the point where you want to have an effect inserted. 3. Press the On/Off button for the effect you want to insert. The selected effect is inserted at the cursor position. * Use [ASSIGN] to assign Foot Volume. 4. If you want to change the sequence further, repeat Steps 2 and 3. 5. If you want to save the sequence youve set up, use the Write procedure (p. 25) to save it to a User patch. Press [EXIT] to return to the Play screen.
3. Rotate the PATCH/VALUE dial to change the characters. * You can use the following functions when changing text characters. CAPS: INS: DEL: Switches the character at the cursor position between upper and lower case. Inserts a blank space at the cursor position. Deletes the character at the cursor position and shifts the characters following it to the left.
4. If you want to edit names further, repeat Steps 2 and 3. 5. If you want to save the sequence youve set up, use the Write procedure (p. 25) to save it to a User patch. Press [EXIT] to return to the Play screen.
Effects can be switched on and off even while making the settings for the connection order (excluding FV, NS, and USB). With effects appearing to the left and right of the cursor, the ON/OFF button corresponding to the effect can be pressed to turn them on/off.
24
Chapter 3 Saving the Tones You Have Created

Storing Patches (PATCH WRITE)
When you want to keep a tone created with the Quick Settings or a tone with altered parameter values, use the Write procedure to save it to a User patch. * If the power is turned off, or if the tone is switched (Patch Change; p. 18) before youve carried out the Write procedure, the newly created tone will be discarded.
fig.03-010
Copying Patches
You can copy a Preset or User patch to another User patch.
fig.03-030
2 Section 3
2,4
1. Select the copy-source patch (refer to How to Switch Patches; p. 18).
1,3
1. Press [WRITE]. The screen for specifying the save-destination User patch appears in the display.
fig.03-020d
2. Press [WRITE]. The screen for specifying the copy-destination patch number appears in the display.
fig.03-040d
Copy-destination patch
Save-destination patch
3. Rotate the PATCH/VALUE dial to select the copydestination User patch. 2. Rotate the VALUE dial to select the save-destination User patch. * This step is unnecessary if the current User patch is acceptable. * To cancel the Write procedure, press [EXIT]. The Play screen returns to the display. 3. Press [WRITE]. The GS-10 switches to the write-destination patch, and youre returned to the Play screen. * The sound of the patch previously stored at the write destination will be lost once the write is executed. * To cancel the copy, press [EXIT]. The Play screen returns to the display. 4. Press [WRITE]. The GS-10 switches to the copy-destination patch, and youre returned to the Play screen. * The sound of the patch previously stored at the copy destination will be lost once the copy is executed.
25
Exchanging Patches
On the GS-10, you can swap or exchange the positions of two User patches. The following explains how this is done.
fig.03-050
Initializing Patches
You can return (initialize) the User patches to their original standard settings.
fig.03-061
4 3
2,5
1. Select the exchange source patch. * Refer to Patch Change (p. 18). 2. Press [WRITE]. 3. Press PARAMETER [ ].
2,4
1. Select the User patch you want to initialize. * Refer to Patch Change (p. 18). 2. Press [WRITE]. 3. Press PARAMETER [ ] twice.
The screen for specifying the exchange-destination patch number appears in the display.
fig.03-060d
The screen for specifying the initialize-destination patch number appears in the display.
fig.03-062d
Exchange-destination patch
User patch to be initialized
4. Rotate the PATCH/VALUE dial to select the exchange destination User patch. * To cancel the exchange, press [EXIT]. The Play screen returns to the display. 5. Press [WRITE]. The patch stored in the exchange source memory location and the patch stored in the exchange destination memory location are exchanged, and youre returned to the Play screen.
* You can use the PATCH/VALUE dial to change the selection of the User patch to be initialized. * To cancel the initialization, press [EXIT]. The Play screen returns to the display. 4. Press [WRITE]. The GS-10 switches to the initialized patch, and the Play screen returns to the display. * The tones stored in patches are lost once the initialization is executed.
26
Registering Your Favorite Patches (DIRECT PATCH)

You can register preferred patches to DIRECT PATCH [1][4] and then press these buttons to call up the corresponding patches directly.
fig.03-070
Copying the PREAMP/SPEAKER Settings to Another Channel

You can take the PREAMP/SPEAKER settings for one channel and copy them to another channel.
fig.03-090
1,3 3 2
Section 3
2,4 4 1
1. Select the copy-source channel. 1. Press [SYSTEM] a number of times until DIRECT PATCH is displayed.
fig.03-080d
2. Press [WRITE]. 3. Press CHANNEL SELECT [A][C] to select the copydestination channel. The channel copy screen appears in the display. * If you press the button for the same channel as the copy source, a channel other than the copy-source channel is selected for the copy destination.
fig.03-100d
2. Press PARAMETER [ ][ ] to select the number of the DIRECT PATCH button to which you want to register the patch. 3. Use the PATCH/VALUE dial to select the patch you want to register. 4. Press [EXIT] to return to the Play screen.
Copy-source channel Copy-destination channel
You can also register patches by selecting the patch in the Play screen, then pressing one of the DIRECT PATCH [1][4] buttons after pressing the [WRITE] button. In this case, the patch appearing in the display is registered. * When a patch is registered using this method, the current settings are also saved along with the patch when its registered. If you want to register only the patch, use the regular registration method.
* To change the copy-source or copy-destination channel, press PARAMETER [ ][ ] to move the cursor to the copysource or copy-destination channel, then press CHANNEL SELECT [A][C]. You can alternatively rotate the PATCH/VALUE dial to change the channel at the cursor position. * When the copy-source channel is changed, the tone is changed as well. * To cancel the copy, press [EXIT]. The Play screen returns to the display. 4. Press [WRITE]. The settings are copied. * If you want to keep a tone for which you have made settings, use the Write procedure (p. 25) to save it to a User patch.
27
Chapter 4 Introduction to Effects and Parameters

In this chapter you will find detailed descriptions for each of the GS-10s onboard effects, and the parameters used to control them.
PREAMP/SPEAKER (Preamp/ Speaker Simulator)

COSM technology plays an indispensable role in simulating the distinguishing characteristics of various guitar amps in the Preamp section, and is also used to simulate various speaker sizes and cabinet constructions in the Speaker Simulator. Parameter On/Off CH Select Type Gain Bass Middle Treble Presence Level Bright Gain SW SP Type (*) Value Off, On A, B, C refer to p. 29 0120 0100 0100 0100 0100 0100 Off, On Low, Middle, High Off, Original, 1x8, 1x10, 1X12, 1X15, 1X18, 2X12, 2X15, 4X10, 4X12, 8X10, 8X12, Custom 1, Custom 2 DYN57, DYN421, CND451, CND87, FLAT Off Mic, On Mic Center, 110 0100 0100
The sound being input to each effect is called the direct sound, and the sound modified by the effect is called the effect sound. * Setting values for gain and volumerelated parameters in the effects too high may result in oscillation.
To derive the maximum performance from the GS-10, be sure to make the correct setting for INPUT SELECT (p. 19), the one thats most suitable for your setup. You may not be able to achieve the expected effect if this is not set correctly. * Depending on the type of bass guitar you are using, you may not be able to achieve the intended effect if the input level to the GS-10 is excessively high. In such cases, lower the volume or tone of your bass guitar.
The trademarks listed in this document are trademarks of their respective owners, which are separate companies from BOSS. Those companies are not affiliated with BOSS and have not licensed or authorized BOSSs GS-10. Their marks are used solely to identify the equipment whose sound is simulated by BOSSs GS-10.
Mic Type (*) Mic Dis. (*) Mic Pos. (*) Mic Level (*) Direct Level (*)
(*) No effect when OUTPUT Select is set to Line/Phones.
On/Off (Effect On/Off)

Turns the PREAMP/SPEAKER effect on/off.
CH Select (Channel Select)

Selects the preamp channel whose settings are to be changed.
28
Type
This sets the type of the guitar preamp. This is the sound of the Roland JC-120. This is a sound suited to jazz. This is a sound with flat response. Good for Full Range acoustic guitar Warm Clean This gives a mellow, clean sound. Clean TWIN This models a Fender Twin Reverb. Pro Crunch This models a Fender Pro Reverb. This models a Fender Bassman 4 x 10 Tweed Combo. This is a crunch sound that can produce Crunch natural distortion. Blues This is a sound suited to blues. This is a crunch sound with wild distorWild Crunch tion. This models the drive sound of a VOX ACVO Drive 30TB. This models the lead sound of the VOX VO Lead AC-30TB. This models the sound input to left input MATCH Drive on a Matchless D/C-30. This models the sound of a MATCHLESS Fat MATCH with a modified high gain. This models the lead sound of the MESA/ BG Lead Boogie combo amp. This models a MESA/Boogie with TREBLE BG Drive SHIFT SW on. This models the rhythm channel of a BG Rhythm MESA/Boogie. Smooth Drive This is a smooth drive sound. This models the sound input to Input I on a MS1959 (I) Marshall 1959. This models the sound input to Input II on MS1959 (II) a Marshall 1959. This models the sound of a Marshall 1959 MS1959 (I+II) with Inputs I and II connected in parallel. This models the sound of a Marshall with a MS HiGain modified midrange boost. This provides the sound of a stack amp Power Stack with active type tone circuitry. This models the lead channel of a MESA/ R-FIER Red Boogie Dual Rectifier. This models the rhythm channel of a R-FIER Orng MESA/Boogie Dual Rectifier. This models a MESA/Boogie Rectifier with R-FIER Vint VINTAGE SW on. This models a Hughes & Kettner Triamp T-AMP Clean AMP1. This models a Hughes & Kettner Triamp T-AMP Crunch AMP2. This models a Hughes & Kettner Triamp T-AMP Lead AMP3. SLDN This models a Soldano SLO-100. Drive Stack This is a drive sound with high gain. JC-120 Jazz Combo
This is a lead sound with high gain. This models the lead channel of a Peavey 5150 Drive EVH 5150. Metal Stack This is a drive sound suited to metal. Metal Lead This is a lead sound suited to metal. CONCERT 810 This models a Ampeg SVT. SESSION This models a SWR SM-400. BASS 360 This models a acoustic 360. T.E. This models a Trace Elliot AH600SMX. B-MAN This models a Fender Bassman100. FLIP TOP This models a Ampeg B-15. This clean sound is great for use with bass Bass Clean guitars. This is a crunch sound with natural distorBass Crunch tion that sounds great with bass guitars. This is a high-gain sound suitable for use Bass HiGain with bass guitars. Mic Preamp Preamp suitable for vocals. Custom 1 Custom amp 1 Custom 2 Custom amp 2 Custom 3 Custom amp 3 Lead Stack * When the type is set to CONCERT 810, SESSION, BASS 360, T.E., B-MAN, FLIP TOP, Bass Clean, Bass Crunch, Bass HiGain, or Mic Preamp set OUTPUT SELECT (p. 16) as shown below to match the GS-10 to the type of amp to be connected. When connecting to an audio amp or similar equipment: Line/Phones When connecting to a guitar amp: Combo Amp or Combo Return When connecting to a bass amp: Stack Amp or Stack Return
Section 4
29
When CUSTOM 13 is selected for Type

You can set the following parameters when Type is set to CUSTOM. Customizing the COSM Amps (p. 55)
Gain SW
Provides for selection from three levels of distortion: Low, Middle, and High. Distortion will successively increase for settings of Low, Middle and High. * The sound of each Type is created on the basis that the Gain is set to Middle. So, normally set it to Middle.
EDIT CUSTOM PRE 13

Parameter Type Value JC Clean, TW Clean, Crunch, VO Lead, BG Lead, MS1959 Stk, Modern Stk -50+50 -50+50 -50+50 -50+50 -50+50 -50+50
SP Type (Speaker Type)

Off Original 1x8 1x10 1x12 1x15 This turns off the speaker simulation. This is the built-in speaker of the amp you selected with Type. This is a compact open-back speaker cabinet with one 8-inch speaker. This is a compact open-back speaker cabinet with one 10-inch speaker. This is a compact open-back speaker cabinet with one 12-inch speaker. This is a compact open-back speaker cabinet with one 15-inch speaker. This is a compact open-back speaker cabinet with one 18-inch speaker. This is a general open-back speaker cabinet with two 12-inch speakers. This is a general open-back speaker cabinet with two 15-inch speakers. This is an optimal speaker cabinet for a large enclosed amp with four 10-inch speakers. This is an optimal speaker cabinet for a large enclosed amp with four 12-inch speakers. This is a double stack of two cabinets, each with four 10-inch speakers. This is a double stack of two cabinets, each with four 12-inch speakers. Custom speaker 1 Custom speaker 2
Bottom Edge Bass Freq Treble Freq Preamp Low Preamp High
Gain
Adjusts the distortion of the amp.
1x18 2x12 2x15 4x10
Bass
Adjusts the tone for the low frequency range.
Middle
Adjusts the tone for the middle frequency range.
Treble
Adjusts the tone for the high frequency range.
4x12 8x10 8x12 Custom 1 Custom 2
Presence
Adjusts the tone for the ultra high frequency range.
Level
Adjusts the volume of the entire preamp. * Be careful not to raise the Level setting too high.
Bright
Turns the bright setting on/off.
When Custom 12 is selected for SP Type

You can set the following parameters when SP Type is set to Custom 12. Customizing the Speakers (p. 56)
Off:
Bright is not used.
On:
Bright is switched on to create a lighter and crisper tone. * Depending on the Type setting, this may not be displayed.
30
EDIT CUSTOM SP 1 2
Parameter Speaker Size Color Low Color High Speaker Num Cabinet Value 515 -10+10 -10+10 x1, x2, x4, x8 Open, Close
COMP (Compressor)
This is an effect that produces a long sustain by evening out the volume level of the input signal. You can also use it as a limiter to suppress only the sound peaks and prevent distortion. Parameter On/Off Sustain Level Value Off, On 0100 0100
Mic Type
This setting selects the simulated mic type. General dynamic mic used for instruments and vocals. Optimal for use in miking guitar amps. Dynamic mic with extended low end. Small condenser mic for use with instruments. Condenser mic with flat response. Simulates a mic with perfectly flat response. Produces a sonic image close to that of listening to the sound directly from the speakers (on site).
DYN57 DYN421 CND451 CND87 FLAT

Turns the COMP effect on/off.
Sustain
Adjusts the range (time) over which low-level signals are boosted. Larger values will result in longer sustain.
Section 4
Level
Adjusts the volume.
Mic Dis. (Mic Distance)

Simulates the distance between the mic and speaker.
Off Mic:
This setting points the mic away from the speaker.
On Mic:
Provides conditions whereby the mic is directed more towards the speaker.
Mic Pos. (Mic Position)

This simulates the microphone position. Center simulates the condition that the microphone is set in the middle of the speaker cone. 1-10 means that the microphone is moved away from the center of the speaker cone.
Mic Level
Adjusts the volume of the microphone.
Direct Level
Adjusts the volume of the direct sound.
31
OD/DS (Overdrive/Distortion)
This effect distorts the sound to create long sustain. It provides 22 types of distortion and three different custom settings. Parameter On/Off Type Drive Bass Treble Effect Level Direct Level Value Off, On refer to below 0100 -50+50 -50+50 0100 0100
Custom 1 Custom 2 Custom 3
Custom OD/DS 1 Custom OD/DS 2 Custom OD/DS 3
When CUSTOM 13 is selected for Type

You can set the following parameters when TYPE is set to Custom 13. Customizing Overdrive and Distortion (p. 56)
EDIT CUSTOM DS 13
Parameter Type Value OD-1, OD-2, CRUNCH, DS-1, DS-2, METAL-1, METAL-2, FUZZ -50+50 -50+50 -50+50 -50+50

Turns the OD/DS effect on/off.
Type
Selects the type of distortion. Blues OD Turbo OD Booster OD-1 T-Scream Natural OD Bass OD Distortion RAT GUV DS Mild DS Solid DS DST+ Metal Zone R-MAN Heavy Metal Loud Sharp Mechanical 60s FUZZ Oct FUZZ MUFF FUZZ This is a crunch sound of the BOSS BD-2. This is the high-gain overdrive sound of the BOSS OD-2. This is a booster that works very well with COSM amps. This is the sound of the BOSS OD-1. This models an Ibanez TS-808. This is an overdrive sound that provides a natural-sounding distortion. This is an overdrive sound that works well with bass guitars. This gives a basic, traditional distortion sound. This models a Proco RAT. This models an Marshall GUV NOR. This is a distortion sound that provides a mild distortion. This is a distortion sound featuring an edge effect. This models an MXR DISTORTION+. This is the sound of the BOSS MT-2. This models a ROCKMAN. This creates a heavier distortion sound. This is a distortion sound with a boosted low end. This is a distortion sound with a boosted high end. This distortion sound boosts the low and high ends, yielding a mechanical-sounding distortion. This models a FUZZFACE. This models an ACETONE FUZZ. This models an Electro-Harmonix Big Muff .
Bottom Top Low High
Drive
Adjusts the depth of distortion.
Bass
Treble
Adjusts the tone for the high frequency range.
Effect Level
Adjusts the volume of the overdrive/distortion sound.
Direct Level
32
DELAY
This effect adds delayed sound to the direct sound, giving more body to the sound or creating special effects. Parameter On/Off Type DlyTime Delay Time.F Tap Time Feedback High Cut Effect Level Value Off, On Single, Pan, Stereo 0 ms1800 ms, BPM BPM 0 msec20 msec 0%100% (Type = Pan) 0100 700 Hz11.0 kHz, Flat 0120
Tap Time
Adjusts the delay time of the right channel delay. This setting adjusts the R channel delay time relative to the L channel delay time (considered as 100%).
Feedback
Feedback is returning a delay signal to the input. This parameter determines the amount of feedback. A higher value will increase the number of the delay repeats.
High Cut (High Cut Filter)

This sets the frequency at which the high cut filter begins to take effect. This allows you to get a mild effect sound by cutting the high-end component above the set frequency. When it is set to Flat, the high cut filter is off or has no effect.

Turns the DELAY Effect on/off.
Section 4
Effect Level
This adjusts the volume of the delay sound.
Type
This selects which type of delay.
Single:
By adjusting the delay time and feedback, you can obtain a normal delay effect.
After [TAP] is pressed several times, the interval between presses of the button is then used as the delay time setting. You can change the Master BPM by setting the delay time to the BPM and pressing [TAP] several times.
Pan:
This delay is specifically for stereo output. This allows you to obtain the tap delay effect that divides the delay time, then deliver them to L and R channels.
fig.04-010
Feedback Effect Level
INPUT
DELAY
Delay Time
OUTPUT L
Effect Level
Tap Time
OUTPUT R
Stereo:
The direct sound is output from the left channel, and the effect sound is output from the right channel.
DlyTime (Delay Time)

This determines the delay time. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the time to twice or four times the time length of the BPM when the set time is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
DlyTime.F (Delay Time Fine)

Make fine adjustments to the delay time.
33
CHORUS
In this effect, a slightly detuned sound is added to the original sound to add depth and breadth. Parameter On/Off Mode Rate Depth Pre Delay Low Cut High Cut Effect Level Value Off, On Mono, Stereo1, Stereo2 0100, BPM BPM 0100 0.0 msec40.0 msec Flat, 55 Hz 800 Hz 700 Hz 11.0 kHz, Flat 0100
Low Cut (Low Cut Filter)

This sets the frequency at which the low cut filter begins to take effect. This lets you cut the low-end component below the set frequency to create a clear, distinct low end, thereby bringing out the high end of the effect. When Flat is selected, the low cut filter will have no effect.

This sets the frequency at which the high cut filter begins to take effect. This allows you to get a mild effect sound by cutting the high-end component above the set frequency. When Flat is selected, the high cut filter will have no effect.
Effect Level
Adjusts the volume of the effect sound.

Turns the CHORUS effect on/off.
REVERB
This effect adds reverberation to the sound. Parameter On/Off Type Rev Time Pre Delay Low Cut High Cut Density Effect Level Value Off, On Ambience, Room, Hall 1, Hall 2, Plate 0.1 sec10.0 sec 0 msec100 msec Flat, 55.0 Hz800 Hz 700 Hz11.0 kHz, Flat 010 0100
Mode
Selection for the chorus mode.
Mono:
This chorus effect outputs the same sound from both L and R.
Stereo1:
This is a stereo chorus effect that adds different chorus sounds to L and R.
Stereo2:
This is a stereo chorus effect produced by synthesizing the spatial characteristics of the direct sound and the effect sound.
Rate
Adjusts the rate of the chorus effect. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.

Turns the REVERB effect on/off.
Type
This selects the reverb type. Various different simulations of space are offered. Simulates an ambience mic (off-mic, placed at a distance from the sound source) used in recording and other applications. Rather than emphasizing the reverberation, this reverb is used to produce a sense of openness and depth. Simulates the reverberation in a small room. Provides warm reverberations. Simulates the reverberation in a concert hall. Provides clear and spacious reverberations. Simulates the reverberation in a concert hall. Provides warm reverberations. Simulates plate reverberation (a reverb unit that uses the vibration of a metallic plate). Provides a metallic sound with a distinct upper range.
Ambience
Depth
Adjusts the depth of the chorus effect. To use it for doubling effect, set the value to 0.
Room Hall 1
Pre Delay
Adjusts the time needed for the effect sound to be output after the direct sound has been output. By setting a longer pre delay time, you can obtain an effect that sounds like more than one sound is being played at the same time (doubling effect). Hall 2
Plate
34
Rev Time (Reverb Time)

Adjusts the length (time) of reverberation.
EQ (Equalizer)
Adjusts the tone. Parametric control is provided for the highmid range and low-mid range. Parameter Value Off, On -20 dB+20 dB 20.0 Hz10.0 kHz 0.516 -20 dB+20 dB 20.0 Hz10.0 kHz 0.516 -20 dB+20 dB -20 dB+20 dB -20 dB+20 dB
Pre Delay
Adjusts the time until the reverb sound appears.


This sets the frequency at which the high cut filter begins to take effect. This allows you to get a mild effect sound by cutting the high-end component above the set frequency. When Flat is selected, the high cut filter will have no effect.
On/Off Low EQ Lo-Mid f Lo-Mid Q Lo-Mid EQ Hi-Mid f Hi-Mid Q Hi-Mid EQ High EQ Level
Section 4

Switches the EQ effect on/off.
Density
This adjusts the density of the reverb sound.
Low EQ (Low Equalizer)

Adjusts the low frequency range tone.
Effect Level
Adjusts the volume of the reverb sound.
Lo-Mid f (Low-Middle Frequency)

Specify the center of the frequency range that will be adjusted by the Lo-Mid EQ.
Lo-Mid Q (Low-Middle Q)
Adjusts the width of the area affected by the EQ centered at the Lo-Mid f. Higher values will narrow the area.
Lo-Mid EQ (Low-Middle Equalizer)

Adjusts the low-middle frequency range tone.
Hi-Mid f (High-Middle Frequency)

Specify the center of the frequency range that will be adjusted by the Hi-Mid EQ.
Hi-Mid Q (High-Middle Q)
Adjusts the width of the area affected by the EQ centered at the Hi-Mid f. Higher values will narrow the area.
Hi-Mid EQ (High-Middle Equalizer)

Adjusts the high-middle frequency range tone.
High EQ (High Equalizer)

Adjusts the high frequency range tone.
Level
Adjusts the volume after the equalizer.
35
FX-1
With FX-1, you can select the effect to be used from the following. PEDAL WAH AUTO WAH TONE MODIFY ADV. COMP (Advanced Compressor) LIMITER ENHANCER SLOW GEAR TREMOLO DEFRETTER RING MOD (Ring Modulator) FEEDBACKER Parameter On/Off FX Select Value Off, On PW, AW, TM, ACS, LM, ENH, SG, TR, DF, RM, FB
Type
This selects the wah type. CRY Wah VO Wah Fat Wah Light Wah 7String Wah Reso Wah Bass Wah Custom 1 Custom 2 Custom 3 This models the sound of the CRY BABY wah pedal popular in the `70s. This models the sound of the VOX V846. This is a wah sound featuring a bold tone. This wah has a refined sound with no unusual characteristics. Wah featuring a broader range of variations for the seven-string guitar. This completely original effect offers enhancements on the characteristic resonances produced by analog synth filters. This is a wah suitable for use with bass guitars. Custom wah 1 Custom wah 2 Custom wah 3
When Type Is Set to Custom13

You can select the following parameters when type is set to Custom13. Customizing Pedal Wah (p. 57)
EDIT CUSTOM WAH13

Parameter Type Q Range Low Range High Presence Value CRY WAH, VO WAH, Fat WAH, Light WAH, 7String WAH -50+50 -50+50 -50+50 -50+50

Switches the FX-1 effect on/off.
FX Select (Effect Select)

This selects the effect to be used.
PW (Pedal Wah)
This provides an effect that works like a wah pedal. With PW selected, the expression pedal connected to the GS10 can be automatically set to function as a wah pedal. Setting the External Expression Pedal Functions (Expression Pedal Function) (p. 58) Parameter Type Value CRY Wah, VO Wah, Fat Wah, Light Wah, 7String Wah, Reso Wah, Bass Wah, Custom 1, Custom 2, Custom 3 0100 0100
Pdl Position (Pedal Position)

This adjusts the position of the wah pedal.
Level
Adjusts the volume.
AW (Auto Wah)
This changes the filtering over a periodic cycle, providing an automatic wah effect. Parameter Mode Polarity Sens Freq Peak Rate Depth Level Value LPF, BPF Down, Up 0100 0100 0100 0100, BPM 0100 0100 BPM
Pdl Position Level
36
Mode
Selection for the wah mode.
TM (Tone Modify)
This changes the characteristics of the connected guitar. Parameter Type Value Fat, Presence, Mild, Tight, Enhance, S H, H S, H HF, S Hollow, H Hollow, S AC, H AC, P AC -50+50 -50+50 0100
LPF (Low Pass Filter):

This creates a wah effect over a wide frequency range.
BPF (Band Pass Filter):

This creates a wah effect in a narrow frequency range.
Polarity
Selection for the direction in which the filter will change in response to the input. Low High Level
Up:
The frequency of the filter will rise.
Down:
The frequency of the filter will fall.
Type
This selects the type of tone modification.
Section 4
Sens (Sensitivity)
This adjusts the sensitivity at which the filter will change in the direction determined by the polarity setting. Higher values will result in a stronger response. With a setting of 0, the strength of picking will have no effect.
Fat Presence Mild Tight Enhance S H H S H HF S Hollow
Frequency
This adjusts the center frequency of the Wah effect.
Peak
Adjusts the way in which the wah effect applies to the area around the center frequency. Lower values will produce a wah effect over a wide area around the center frequency. Higher values will produce a wah effect in a narrow area around the center frequency. * With a value of 50 a standard wah sound will be produced.
H Hollow S AC H AC P AC
Rate
Adjusts the frequency of the auto wah. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
Fat tone with boosted mid range. Bright tone with boosted high-mid range. Mild tone with the high end cut back. Tone with the low frequencies cut. Tone with the high frequencies boosted. Changes from a single-coil pickup tone to a humbucking pickup tone. Changes from a humbucking pickup tone to a mixed tone of two single-coil pickups. Changes from a humbucking pickup tone to a single-coil pickup half tone. Changes a single-coil pickup tone to a fullacoustic tone with the body resonance added. Changes a humbucking pickup tone to a full-acoustic tone with the body resonance added. Changes a single-coil pickup tone to an acoustic guitar tone. Changes a humbucking pickup tone to an acoustic guitar tone. Changes a piezo pickup tone to an acoustic guitar tone.
Low
High
Adjusts the tone for the High frequency range
Depth
Adjusts the depth of the auto wah effect.
Level
Adjusts the volume.
Level
Adjusts the volume.
37
ACS (Advanced Compressor)

This is an effect that produces a long sustain by evening out the volume level of the input signal. You can also use it as a limiter to suppress only the sound peaks and prevent distortion. Parameter Type Sustain Attack Tone Level Value Stereo Comp, BOSS Comp, D-Comp 0100 0100 -50+50 0100
LM (Limiter)
The limiter attenuates loud input levels to prevent distortion. Parameter Type Attack Threshold Ratio Release Level Value Stereo LM, Rack 160D, Vtg Rack U 0100 0100 1:1 :1 0100 0100
Type
Selects the limiter type. Stereo LM Rack 160D Vtg Rack U This selects a stereo limiter. This models a dbx 160X. This models a UREI 1178.
Type
Selects the compressor type. Stereo Comp BOSS Comp D-Comp This selects a stereo compressor. This models a BOSS CS-3. This models a MXR DynaComp.
Attack
Adjusts the strength of the picking attack when the strings are played. Higher values result in s sharper attack, creating a more clearly defined sound.
Sustain
Adjusts the range (time) over which low-level signals are boosted. Larger values will result in longer sustain.
Attack
Adjusts the strength of the picking attack. Larger values will result in a sharper attack, creating a more clearly defined sound.
Threshold
Adjust this as appropriate for the input signal from your guitar. When the input signal level exceeds this threshold level, limiting will be applied.
Tone
Adjusts the tone.
Ratio
This selects the compression ratio used with signals in excess of the threshold level.
Level
Adjusts the volume.
Release
This adjusts the time from when the signal level drops below the threshold until when limiting is removed.
Tone
Adjusts the tone.
Level
Adjusts the volume.
38
ENH (Enhancer)
By adding sounds which are out-of-phase with the direct sound, this effect enhances the definition of the sound, and pushes it to the forefront. Parameter Sens Freq Mix Level Value 0100 800 Hz10.0 kHz 0100
TR (Tremolo)
Tremolo is an effect that creates a cyclic change in volume. Parameter Wave Shape Rate Depth Value 0100 0100, BPM 0100 BPM
Wave Shape
This adjusts changes in volume level.
Sens (Sensitivity)
Adjusts the manner in which the enhancer will be applied relative to the input signals.
Rate
Adjusts the frequency (speed) of the change. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
Freq (Frequency)
Adjusts the frequency at which the enhancer effect will begin to be applied. The effect will be made apparent in the frequencies above the frequency set here.
Section 4
Mix Level
Adjusts the amount of phase-shifted sound of the range set by Frequency that is to be mixed with the input.
Depth
SG (Slow Gear)
This produces a volume-swell effect (violin-like sound). Parameter Sens Rise Time Value 0100 0100
Adjusts the depth of the effect.
Sens (Sensitivity)
This adjusts the sensitivity of the slow gear. When it is set to a lower value, the effect of the slow gear can be obtained only with a stronger picking, while no effect is obtained with a weaker picking. When the value is set higher, the effect is obtained even with a weak picking.
Rise Time
This adjusts the time needed for the volume to reach its maximum from the moment you begin picking.
39
DF (Defretter)
This simulates a fretless guitar. Parameter Tone Sens Attack Depth Resonance Effect Level Direct Level Value -50+50 0100 0100 0100 0100 0100 0100
Intelligent:
By ring-modulating the input signal, a bell like sound is created. The intelligent ring modulator changes the oscillation frequency according to the pitch of the input sound and therefore produces a sound with the sense of pitch, which is quite different from Normal. This effect does not give a satisfactory result if the pitch of the guitar sound is not correctly detected. So, you must use single notes, not chords.
Freq (Frequency)
This adjusts the frequency of the internal oscillator.
Tone
Adjusts the amount of blurring between the notes.
Effect Level
This adjusts the volume of the effect sound.
Sens (Sensitivity)
This controls the input sensitivity of the defretter.
Direct Level
This adjusts the volume of the direct sound.
Attack
Adjusts the attack of the picking sound.
FB (Feedbacker)
This allows you to use feedback playing techniques. * Note that the notes you want to apply feedback to must be played singly and cleanly. * You can use the foot switch to switch the effect on and off. For more details, refer to Setting the External Pedal Function for Individual Patches (Assign) (p. 60). Parameter Mode Rise Time Rise Time () F.B.Level F.B.Level () Vib Rate Vib Depth Value OSC, Natural 0100 Mode= OSC 0100 Mode= OSC 0100 0100 Mode= OSC 0100, BPM 0100 BPM Mode= OSC Mode= OSC
Depth
This controls the rate of the harmonics.
Resonance
Adds a characteristically resonant quality to the sound.
Effect Level
Adjust the volume of the defretter sound.
Direct Level
Adjust the volume of the direct sound.
RM (Ring Modulator)
This creates a bell-like sound by ring-modulating the guitar sound with the signal from the internal oscillator. The sound will be unmusical and lack distinctive pitches. Parameter Mode Freq Effect Level Direct Level Value Normal, Intelligent 0100 0100 0100
Mode
Select either oscillator OSC or natural Natural.
OSC (Oscillator):
An artificial feedback sound will be created internally. * When OSC is selected, the effect is activated after a single note is played and the note stabilizes. A feedback effect is created when the effect switches on; the feedback disappears when the OSC effect switches off.
Mode
This selects the mode for the ring modulator.
Natural:
Analyzes the pitch of the guitar sound being input, and then creates a feedback sound.
Normal:
This is a normal ring modulator.
40
Rise Time
This determines the time needed for the volume of the feedback sound to reach its maximum from the moment the effect is turned on.
FX-2
With FX-2, you can select the effect to be used from the following. PHASER FLANGER HARMONIST PITCH SHIFT (Pitch Shifter) OCTAVE PEDAL BEND 2x2 CHORUS PAN VIBRATO
Rise Time ()
This determines the time needed for the volume of the one octave higher feedback sound to reach its maximum from the moment the effect is turned on.
F.B.Level (Feedback Level)

Adjusts the volume of the feedback sound.
F.B.Level ()
This adjusts the volume of the one octave higher feedback sound.
Section 4
Vib Rate (Vibrato Rate)

This adjusts the rate of the vibrato when the feedbacker is on. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
UNI-V ROTARY SHORT DELAY HUMANIZER SLICER AUTO RIFF GUITAR SYNTH BASS SIM. (Bass Simulator) STEREO EQ (Stereo Equalizer) Parameter On/Off FX Select Value Off, On PH, FL, HR, PS, OC, PB, 2CE, PAN, VB, UV, RT, SDD, HU, SL, AR, SYN, BS, SEQ
Vib Depth (Vibrato Depth)

This adjusts the depth of the vibrato when the feedbacker is on.

Switches the FX-2 effect on/off.
FX Select (Effect select)

This selects the effect to be used.
41
PH (Phaser)
By adding varied-phase portions to the direct sound, the phaser effect gives a whooshing, swirling character to the sound. Parameter Type Rate Depth Manual Resonance Step Rate Effect Level Direct Level Value 4 Stage, 8 Stage, 12 Stage, Bi-Phase 0100, BPM 0100 0100 0100 BPM
Step Rate
This sets the cycle of the step function that changes the rate and depth. When it is set to a higher value, the change will be finer. Set this to Off when not using the Step function. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
Off, 0100, BPM 0100 0100
BPM
Effect Level
This adjusts the volume of the phaser.
Type
Selects the number of stages that the phaser effect will use. 4 Stage 8 Stage 12 Stage Bi-Phase This is a four-phase effect. A light phaser effect is obtained. This is an eight-phase effect. It is a popular phaser effect. This is a twelve-phase effect. A deep phase effect is obtained. This is the phaser with two phase shift circuits connected in series.
Direct Level
FL (Flanger)
The flanging effect gives a twisting, jet-airplane-like character to the sound. Parameter Rate Depth Manual Resonance Separation Low Cut Effect Level Direct Level Value 0100, BPM BPM 0100 0100 0100 0100 Flat, 55.0 Hz800 Hz 0100 0100
Rate
This sets the rate of the phaser effect. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
Rate
This sets the rate of the flanging effect. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
Depth
Determines the depth of the phaser effect.
Manual
Adjusts the center frequency of the phaser effect.
Resonance
Determines the amount of resonance (feedback). Increasing the value will emphasize the effect, creating a more unusual sound.
Depth
Determines the depth of the flanging effect.
Manual
Adjusts the center frequency at which to apply the effect.
42
Resonance
Determines the amount of resonance (feedback). Increasing the value will emphasize the effect, creating a more unusual sound.
2-Stereo:
Two-voice pitch-shifted sound (HR1, HR2) output through left and right channels.
Harm (Harmony)
This determines the pitch of the sound added to the input sound, when you are making a harmony. It allows you to set it by up to 2 octaves higher or lower than the input sound. When the scale is set to Scale 1Scale29, this parameter sets the user scale number to be used.
Separation
Adjusts the diffusion. The diffusion increases as the value increases.

PreDly (Pre Delay)

Adjusts the time from when the direct sound is heard until the harmonist sounds are heard. Normally you can leave this set at 0ms. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the time to twice or four times the time length of the BPM when the set time is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
Effect Level
This adjusts the volume of the flanger.
Section 4
Direct Level
HR (Harmonist)
Harmonist is an effect where the amount of shifting is adjusted according to an analysis of the guitar input, allowing you to create harmonics based on diatonic scales. * Because of the need to analyze the pitch, chords (two or more sounds played simultaneously) cannot be played. Parameter Voice Harm PreDly Feedback Level Key Direct Level (User Scale) User DIR EFF Value 1-Voice, 2-Mono, 2-Stereo -2oct+2oct, Scale1Scale29 0 ms300 ms, BPM 0100 0100 C (Am)B (G#m) 0100 129 CB CB (2 octave) BPM
Feedback
This adjusts the feedback amount of the harmonist sound.
Level
This adjusts the volume.
Key
Specify the key of the song you are playing. By specifying the key, you can create harmonies that fit the key of the song. The key setting corresponds to the key of the song (#, b) as follows.
fig.04-020
Voice
This selects the number of voices for the pitch shift sound (harmony).
1-Voice:
One-voice pitch-shifted sound output in monaural.
Direct Level
2-Mono:
Two-voice pitch-shifted sound (HR1, HR2) output in monaural.
43
Creating Harmonist Scales (User Scale)

When Harmony is set to any value from -2oct to +2oct, and the harmony does not sound the way you intend, use a User scale. You can set any of 29 different User scales. 1. Press [FX-2], then press PARAMETER [ that FX Select is displayed. ][ ] so
PS (Pitch Shifter)
This effect changes the pitch of the original sound (up or down) within a range of two octaves. Parameter Voice Mode Pitch Fine PreDly Feedback Level Direct Level Value 1-Voice, 2-Mono, 2-Stereo Fast, Medium, Slow, Mono -24 +24 -50+50 0 ms300 ms, BPM 0100 0100 0100 BPM
2. Rotate the PATCH/VALUE dial to select HR. 3. Press PARAMETER [ ][ ] to select HR1 Harm (or HR2 Harm), then rotate the PATCH/ VALUE dial to select a setting from Scale 129. 4. Press PARAMETER [ ] a number of times so that the User scale settings screen is displayed.
fig.04-030d
Voice
This selects the number of voices for the pitch shift sound.
1-Voice:
5. Press PARAMETER [ ][ ] to move the cursor, then rotate the PATCH/VALUE dial to set the User scale. One-voice pitch-shifted sound output in monaural.
2-Mono:
Two-voice pitch-shifted sound (PS1, PS2) output in monaural.
User:
You can change the number of the user scale.
2-Stereo:
Two-voice pitch-shifted sound (PS1, PS2) output through left and right channels.
DIR (Direct):
Sets the note name of the input sound. You can also play individual notes on the guitar and let the GS-10 interpret the note name.
Mode
Selection for the pitch shifter mode.
EFF (Effect):
Sets the note name of the output sound. The triangle next to the note name indicates the octave. One downward-pointing triangle indicates a note one octave below the note displayed; two triangles indicates a two-octave drop. One upward-pointing triangle indicates a note one octave above the note displayed; two triangles indicates a two-octave rise.
Fast, Medium, Slow:

A chord can be input with a normal pitch shifter. The response is slower in the order of Fast, Medium and Slow, but the modulation is lessened in the same order.
Mono:
This mode is used for inputting single notes. Use this setting when you want to achieve a pedal bend effect with an external expression pedal.
Pitch
Adjusts the amount of pitch shift (the amount of pitch change) in semitone steps.
Fine
Make fine adjustments to the pitch shift. * The amount of the change in the Fine 100 is equivalent to that of the Pitch 1.
PreDly (Pre Delay)

Adjusts the time from when the direct sound is heard until the pitch shifted sounds are heard. Normally you can leave this set at 0ms.
44
* When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the time to twice or four times the time length of the BPM when the set time is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
PB (Pedal Bend)
This lets you use the pedal to get a pitch bend effect. The expression pedal automatically switches to the pedal bend function when PB is selected. Setting the External Expression Pedal Functions (Expression Pedal Function) (p. 58). Parameter Pitch Min Pitch Max Pdl Position Effect Level Direct Level Value -24+24 -24+24 0100 0100 0100
Feedback
This adjusts the feedback amount of the pitch shift sound.
Level
Adjusts the volume.
Direct Level
Section 4
Pitch Min
OC (Octave)
This adds a note one octave lower, creating a richer sound. Parameter Range Octave Level Direct Level Value Range 1Range 4 0100 0100
This sets the pitch at the point where the expression pedal is fully lifted.
Pitch Max
This sets the pitch at the point where the expression pedal is all the way down.
Pdl Position (Pedal Position)

This adjusts the pedal position for pedal bend.
Range
This selects the pitch range for the input sound to which you want to add the effects. The range to which the affect is applied changes with the Input Select (p. 19) value. Guitar Microphone USB (Gtr/Mic) AUX 7th string, open (B) to 1st string, 24th fret (E) 7th string, open (B) to 1st string, 12th fret (E) 7th string, open (B) to 1st string, open (E) 7th string, open (B) to 4th string, 2nd fret (E)
Effect Level
This adjusts the volume of the pitch bend sound.
Direct Level
Input Select Range 1 Range 2 Range 3 Range 4
Bass USB Low B, open (B) to High C, 24th fret (C) Low B, open (B) to 1st string, 19th fret (C) Low B, open (B) to 1st string, 9th fret (E) Low B, open (B) to 2nd string, 2nd fret (E)
2CE (2x2 Chorus)

Two separate stereo chorus units are used for the lowfrequency and high-frequency ranges in order to create a more natural chorus sound. Parameter Xover f Lo Rate Lo Depth Lo PreDly Lo Level Hi Rate Hi Depth Hi PreDly Hi Level Value 100 Hz4.00 kHz 0100, BPM BPM 0100 0.0 msec40.0 msec 0100 0100, BPM BPM 0100 0.0 msec40.0 msec 0100
Octave Level
This adjusts the volume of the sound one octave below.
Direct Level
45
Xover f (Crossover Frequency)

This parameter sets the frequency at which the frequency components of the direct sound are divided into bass and treble bands.
Hi Level (High Level)

Adjust the volume of the high frequency range.
PAN
With the volume level of the left and right sides alternately changing, when playing sound in stereo, you can get an effect that makes the guitar sound appear to fly back and forth between the speakers. Parameter Wave Shape Rate Depth Value 0100 0100, BPM 0100 BPM
Lo Rate (Low Rate)

Adjust the speed of the chorus effect for the low frequency range. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
Wave Shape
This adjusts changes in volume level.
Lo Depth (Low Depth)

Adjust the depth of the chorus effect for the low frequency range. If you wish to use this as a doubling effect, use a setting of 0.
Rate
Adjusts the frequency (speed) of the change. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
Lo PreDly (Low Pre Delay)

Adjust the time from when the low frequency range direct sound is output until the effect sound is output. Extending the pre-delay will produce the sensation of multiple sounds (doubling effect).
Lo Level (Low Level)

Adjust the volume of the low frequency range.
Depth
Adjusts the depth of the effect.
Hi Rate (High Rate)

Adjust the speed of the chorus effect for the high frequency range. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
VB (Vibrato)
This effect creates vibrato by slightly modulating the pitch. Parameter Rate Depth Trigger Rise Time Value 0100, BPM 0100 Off, On 0100 BPM
Hi Depth (High Depth)

Adjust the depth of the chorus effect for the high frequency range. If you wish to use this as a doubling effect, use a setting of 0.
Rate
This adjusts the rate of the vibrato. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
Hi PreDly (High Pre Delay)

Adjust the time from when the high frequency range direct sound is output until the effect sound is output. Extending the pre-delay will produce the sensation of multiple sounds (doubling effect).
46
Depth
This adjusts the depth of the vibrato.
RT (Rotary)
This produces an effect like the sound of a rotary speaker.
Trigger
This selects on/off of the vibrato. * It is assumed that this parameter will be assigned (p. 60) to the foot switch.
Parameter Speed Sel Rate (Slow) Rate (Fast) Rise Time Fall Time Depth
Value Slow, Fast 0100, BPM 0100, BPM 0100 0100 0100 BPM BPM
Rise Time
This sets the time passing from the moment the trigger is turned on until the set vibrato is obtained.
UV (Uni-V)
Although this resembles a phaser effect, it also provides a unique undulation that you cant get with a regular phaser. Parameter Rate Depth Level Value 0100, BPM 0100 0100 BPM
Speed Sel (Speed Select)

This parameter changes the simulated speakers rotating speed (Slow or Fast).
Rate (Slow)
This parameter adjusts the speed of rotation when set to Slow.
Section 4
Rate (Fast)
This parameter adjusts the speed of rotation when set to Fast. * When the Rate (Slow) or Rate (Fast) set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
Rate
Adjusts the rate of the Uni-V effect. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
Rise Time
This parameter adjusts the time it takes for the rotation speed to change when switched from Slow to Fast.
Depth
Adjusts the depth of the Uni-V effect.
Level
Adjusts the volume.
Fall Time
This parameter adjusts the time it takes for the rotation speed to change when switched from Fast to Slow.
Depth
This parameter adjusts the amount of depth in the rotary effect.
47
SDD (Short Delay)

This is a delay with the maximum delay time of 400 ms. This effect is useful for making the sound fatter. Parameter DlyTime Feedback Effect Level Value 0 ms400 ms, BPM 0100 0120 BPM
Auto:
By adjusting the rate and depth, two vowels (Vowel 1 and Vowel 2) can be switched automatically.
Random:
Five vowels (a, e, i, o, u) are called out at random by adjusting the rate and depth.
Vowel 1
This selects the first vowel.
fig.04-040d
DlyTime (Delay Time)

Adjusts the delay time. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the time to twice or four times the time length of the BPM when the set time is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
Vowel 1 Vowel 2
Vowel 2
This selects the second vowel.
Sens (Sensitivity)
This adjusts the sensitivity of the humanizer. When it is set to a lower value, no effect of the humanizer is obtained with weaker picking, while stronger picking produces the effect. When it is set to a higher value, the effect of the humanizer can be obtained whether the picking is weak or strong.
Feedback
Feedback refers to returning the delayed signal back into the input of the delay. This parameter adjusts the volume that is returned to the input. Higher settings will result in more delay repeats.
Rate
This adjusts the cycle for changing the two vowels. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
Effect Level
Adjusts the volume of delay sound.
HU (Humanizer)
This can create human vowel-like sounds. Parameter Mode Vowel 1 Vowel 2 Sens Rate Depth Manual Level Value Picking, Auto, Random a, e, i, o, u Mode= Picking, Auto a, e, i, o, u Mode= Picking, Auto 0100 Mode= Picking 0100, BPM BPM 0100 0100 Mode= Auto 0100
Depth
This adjusts the depth of the effect.
Manual
This determines the point where the two vowels are switched. When it is set to 50, vowel 1 and vowel 2 are switched in the same length of time. When it is set to lower than 50, the time for vowel 1 is shorter. When it is set to higher than 50, the time for vowel 1 is longer.
Level
Adjusts the volume.
Mode
This sets the mode that switches the vowels.
Picking:
It changes from vowel 1 to vowel 2 along with the picking. The time spent for the change is adjusted with the rate.
48
SL (Slicer)
This consecutively interrupts the sound to create the impression that a rhythm backing phrase is being played. Parameter Pattern Rate Trigger Sens Value P1P20 0100, BPM 0100 BPM
AR (Auto Riff)
This allows you to automatically produce a phrase simply by picking a single note. This can be used to easily play extremely rapid phrases. * Reception of large amounts of MIDI data while Auto Riff is playing may result in disturbances in the sound. Parameter Phrase Value Preset1Preset30, User1User10 Off, On 0100, BPM BPM 0100 C (Am)B (G#m) Phrase = Preset 0100 Off, On 0100 0100 110 CB 116 CB (2 octave), -, end
Pattern
Select the slice pattern that will be used to cut the sound.
Loop Tempo Sens Key Attack Hold Effect Level Direct Level (User Phrase) User IN STEP OUT
Rate
Adjust the rate at which the sound will be cut. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
Section 4
Trigger Sens (Trigger Sensitivity)

Adjust the sensitivity of triggering. With low settings of this parameter, softly picked notes will not retrigger the phrase (i.e., the phrase will continue playing), but strongly picked notes will retrigger the phrase so that it will playback from the beginning. With high settings of this parameter, the phrase will be retriggered even by softly picked notes.
Phrase
Select the phrase. User-programmed phrases are used when User 110 is selected.
Loop
If Loop is turned On, the phrase will be played back continuously.
Tempo
Adjust the speed of the phrase. * When set to BPM, the value of each parameter will be set according to the value of the Master BPM (p. 54) specified for each patch. This makes it easier to achieve effect sound settings that match the tempo of the song (synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased). When setting to BPM, press PARAMETER [ ] to display the Master BPM settings screen.
Sens (Sensitivity)
Adjust the sensitivity of triggering. With low settings of this parameter, softly picked notes will not retrigger the phrase (i.e., the phrase will continue playing), but strongly picked notes will retrigger the phrase so that it will playback from the beginning. With high settings of this parameter, the phrase will be retriggered even by softly picked notes. No retriggering occurs when the value is set to 0.
49
Key
Select the key of the song that you wish to play.
OUT:
Specify the note name of the output sound. The triangle next to the note name indicates the octave. One downward-pointing triangle indicates a note one octave below the note displayed; two triangles indicates a two-octave drop. One upward-pointing triangle indicates a note one octave above the note displayed; two triangles indicates a two-octave rise.
Attack
Adjust the strength of the attack. By adding an attack to each note of the phrase you can produce a sensation as though the notes were being picked.
Hold
If you turn hold On after you pick a note, the effect sound will continue even after there is no input signal.
Effect Level
Adjust the volume of the phrase.
SYN (Guitar Synth)

This detects the pitch of an electric guitar and outputs a synthesizer sound. * When you use a guitar synthesizer, observe the following points. It does not work properly when a chord is played. Be sure to mute all the other strings and play in a single note. When you are to play the next string while a certain sound is still playing, perfectly mute the previous sound then play the next one with a clear attack. If the unit cannot detect the attack, it may not sound correctly. Parameter Sens Wave Chromatic Octave Shift PWM Rate PWM Depth Cutoff Freq Resonance FLT.Sens FLT.Decay FLT.Depth Attack Release Velocity Hold Synth Level Direct Level Value 0100 Square, Saw, Brass, Bow Off, On Wave= Square, Saw 0, -1, -2 Wave= Square, Saw 0100 Wave= Square 0100 Wave= Square 0100 0100 0100 0100 -100 100 Decay, 0100 0100 0100 Off, On Wave= Square, Saw 0100 0100
Direct Level
Adjust the volume of the direct sound.
Creating Original Phrases (User Phrase)

In addition to the 30 different prepared phrases, you can also create up to ten of your own original phrases (User phrases). 1. Press [FX-2], then press PARAMETER [ that FX Select is displayed. ][ ] so
2. Rotate the PATCH/VALUE dial to select AR. 3. Press [FX-2] a number of times to select Phrase, then rotate the PATCH/VALUE dial to select User 110. 4. Press PARAMETER [ ] a number of times until you have the User Phrase settings screen displayed.
fig.04-050d
5. Press PARAMETER [ ][ ] to move the cursor, then rotate the PATCH/VALUE dial to set the User phrase.
User:
specify the user phrase number.
IN:
Sets the note name of the input sound. You can also play individual notes on the guitar and let the GS-10 judge the note name.
STEP:
Sets the step of the phrase. You can also play on the guitar and put the step forward.
Sens (Sensitivity)
This adjusts the input sensitivity. The response of the internal sound source is better with a higher sensitivity value, but the malfunctions will be increased on the other hand. So, try to set it as high as possible without causing malfunction.
50
Wave
This selects a wave type that is the source of the guitar synthesizer.
Cutoff Freq (Cutoff Frequency)

This adjusts the frequency where the harmonics contents of the sound are cut off.
Square:
The unit detects the pitch and attack information from the input guitar sound, then send the square waveform ( ) from the internal sound generator.
Resonance
This adjusts how much of the harmonics contents around the cutoff frequency should be emphasized.
Saw:
The unit detects the pitch and attack information from the input guitar sound, then send the saw waveform ( from the internal sound generator. )
FLT.Sens (Filter Sensitivity)

This adjusts the sensitivity of the filter. When it is set to a lower value, the filter is affected only with stronger picking. When it is set higher, the filter changes even with weaker picking. When it is set to 0, the depth of the filter will be the same no matter how the picking strength may be.
Brass:
The unit directly processes the input guitar sound and creates a guitar synthesizer sound. It gives a quick sound rise and send the sound with a sharp edge.
FLT.Decay (Filter Decay)

This sets the time needed for the filter to finish its sweep.
Section 4
Bow:
The unit directly processes the input guitar sound and creates a guitar synthesizer sound. It outputs a soft sound without attack.
FLT.Depth (Filter Depth)

This adjusts the depth of the filter. When the value is higher, the filter will change more drastically. The polarity of the filter will be opposite with + and -.
Chromatic
This switches on or off the chromatic function. When it is on, the pitch change of the synthesizer sound is in semitone steps. This does not respond to pitch changes less than a semitone, such as what might be obtained with bending or vibrato. Thus, this is effectively used for realistically playing musical instruments whose pitch will change in steps greater than a semitone, such as a keyboard. * Use this parameter when Square or Saw is selected for wave.
Attack
This adjusts the time needed for a synthesizer sound to reach its maximum. When it is set to a lower value, the sound will rise quickly. When it is set higher, the sound will rise slowly. When it is set to Decay, the sound will rise quickly and turn to a Release status regardless of the input of the guitar sound. * When Brass or Bow is selected for the wave, the attack time will not be quicker from a certain level even if the attack is set to Decay or 0.
Octave Shift
This allows you to shift the pitch of the internal sound module in an octave step from the guitar sound. * This parameter should be set when Square or Saw is selected for the wave.
Release
This determines the time needed for the synthesizer sound to reach zero from the moment the input of the guitar sound is completed. * When Brass or Bow is selected for the wave, the guitar signal itself is processed. That is, the synthesizer sound will go down when the guitar signal goes down no matter how long the release may be set.
PWM Rate (Pulse Wise Modulation Rate)

This gives breadth or fatness to the sound by applying modulation to the waveform (only to Square) in the internal sound module. A higher value will quicken the rate of the modulation. * This parameter should be set only when Square is selected for the wave.
PWM Depth (Pulse Wise Modulation Depth)

This adjusts the depth of the PWM. When it is set to 0, no PWM effect is obtained. * This parameter should be set only when Square is selected for the wave.
51
Velocity
This adjusts the amount of the volume change of the synthesizer sound. When it is set to high, the volume change will be greater depending on the picking strength. When it is set to 0, no volume change is caused even by changing the picking manner.
SEQ (Stereo Equalizer)

This adjusts the tone as a stereo equalizer. A parametric type is adopted for the high-middle and low-middle range. Parameter Low EQ Lo-Mid f Lo-Mid Q Lo-Mid EQ Hi-Mid f Hi-Mid Q Hi-Mid EQ Hi EQ Level Value -20 dB+20 dB 20.0 Hz10.0 kHz 0.516 -20 dB+20 dB 20.0 Hz10.0 kHz 0.516 -20 dB+20 dB -20 dB+20 dB -20 dB+20 dB
Hold
The hold function can sustain the output of the synthesizer sound. If you turn on the hold while a synthesizer sound is being output, the synthesizer sound will be held until you turn it off. * It is assumed that this parameter will be assigned (p. 60) to the foot switch. * This parameter is used when Square or Saw is selected for the wave.
Low EQ (Low Equalizer)

Adjusts the low frequency range tone.
Synth Level
Adjusts the volume of the synthesizer sound.
Lo-Mid f (Low-Middle Frequency)

Specify the center of the frequency range that will be adjusted by the Lo-Mid EQ.
Direct Level
BS (Bass Simulator)
Simulates the sound of a bass guitar. Obtain the sound of a bass guitar while playing an electric guitar. * You should avoid playing chords when using the Bass Simulator. Parameter Character Level Value Loose, Tight 0100
Lo-Mid Q (Low-Middle Q)
Adjusts the width of the area affected by the EQ centered at the Lo-Mid f. Higher values will narrow the area.
Lo-Mid EQ (Low-Middle Equalizer)

Adjusts the Lo-Mid f range tone.
Hi-Mid f (High-Middle Frequency)

Specify the center of the frequency range that will be adjusted by the Hi-Mid EQ.
Hi-Mid Q (High-Middle Q)
Adjusts the width of the area affected by the EQ centered at the Hi-Mid f. Higher values will narrow the area.
Character
Bass tone characteristic is set. When Loose is selected, the sound becomes as if the string gauge was getting thicker.
Hi-Mid EQ (High-Middle Equalizer)

Adjusts the Hi-Mid f range tone.
Level
This adjusts the volume of the bass simulator.
High EQ (High Equalizer)

Adjusts the high frequency range tone.
Level
Adjusts the volume after the equalizer.
52
NAME/NS/MASTER
You can select the following items in NAME/NS/MASTER. Name (Patch Name) Noise Suppressor Master Foot Volume Effect Chain * With each press of [NAME/NS/MASTER], you move to the next item that can be set, in this order: Name Noise Suppressor Master Foot Volume Effect Chain.
Noise Suppressor
This effect reduces the noise and hum picked up by guitar pickups. Since it suppresses the noise in synchronization with the envelope of the guitar sound (the way in which the guitar sound decays over time), it has very little effect on the guitar sound, and does not harm the natural character of the sound. * Please connect the noise suppressor in the signal path prior to the reverberation type effect. This setup will prevent an natural break of the reverberation type effect. Parameter On/Off Threshold Release Value Off, On 0100 0100
Name (Patch Name)

Each patch can be given a name (Patch Name) consisting of up to sixteen characters. Youll probably want to take advantage of this feature by assigning names that suggest the sound youll obtain, or the song in which itll be used. 1. Press [NAME/NS/MASTER] so that the Name edit screen appears in the display.
fig.04-060d
Section 4

Turns the noise suppressor effect on/off. This parameter can be set with the PATCH/VALUE dial. * Even if [NAME/NS/MASTER] is pressed, you cannot switch the noise suppressor on and off.
Threshold
Adjust this parameter as appropriate for the volume of the noise. If the noise level is high, a higher setting is appropriate. If the noise level is low, a lower setting is appropriate. Adjust this value until the decay of the guitar sound is as natural as possible. * High settings for the threshold parameter may result in there being no sound when you play with your guitar volume turned down.
2. Press PARAMETER [ ][ the text area you want to edit.
] to move the cursor to
3. Rotate the PATCH/VALUE dial to change the characters. * You can use the following functions when changing text characters. CAPS: INS: DEL: Switches the character at the cursor position between upper and lower case. Inserts a blank space at the cursor position. Deletes the character at the cursor position and shifts the characters following it to the left.
Release
Adjusts the time from when the noise suppressor begins to function until the noise level reaches 0.
4. If you want to edit names further, repeat Steps 2 and 3. 5. If you want to save the sequence youve set up, use the Write procedure (p. 25) to save it to a User patch. Press [EXIT] to return to the Play screen.
53
Master
Parameter Patch Level Master BPM Value 0200 40250
Foot Volume
This is a volume control effect. Usually, this is controlled to the expression pedal. Parameter Level Value 0100
Patch Level
This adjusts the output volume of the GS-10.
Level
Adjusts the volume.
Master BPM
Adjust the BPM value for each patch. * BPM (beats per minute) indicates the number of quarter note beats that occur each minute. * When you have an external MIDI device connected, the Master BPM synchronizes to the external MIDI devices tempo, making it impossible to set the Master BPM. To enable setting of the Master BPM, set MIDI Sync Clock (p. 69) to Internal.
Effect Chain
Heres how you can change the order in which the effects are connected. 1. Press [NAME/NS/MASTER] until Effect Chain appears in the display. * With each press of [NAME/NS/MASTER], you move to the next item that can be set, in this order: Name Noise Suppressor Master Foot Volume Effect Chain.
fig.04-070d
Control with the Master BPM

To input the Master BPM with the foot switch, set Assign as follows. Quick Setting (p. 60) P11: MSTR BPM TAP Manual Settings (p. 61) Set ASSIGN to ON and set the following as shown. Target: Target Min: Target Max: Source: Source Mode: Act.Range Lo: Act.Range Hi: Master BPM (Tap) Off On CTL 1 (or CTL 2) Normal 0 127
* Effects are shown in lowercase letters when turned off. 2. Use the PATCH/VALUE dial or PARAMETER [ ] [ ] to move the cursor to the point where you want to have an effect inserted. 3. Press the On/Off button for the effect you want to insert. The selected effect is inserted at the cursor position. * Use [ASSIGN] to assign Foot Volume. 4. If you want to change the sequence further, repeat Steps 2 and 3. 5. If you want to save the sequence youve set up, use the Write procedure (p. 25) to save it to a User patch. Press [EXIT] to return to the Play screen.
* When controlling the Assigns with the foot switch, the system parameter CTL 1 Func (or CTL 2 Func) must be set to Assign 1-8 (p. 58, p. 59).
Effects can be switched on and off even while making the settings for the connection order. With effects appearing to the left and right of the cursor, the ON/ OFF button corresponding to the effect can be pressed to turn them on/off.
54
Chapter 5 Creating Original Effects Types (Customize)

With the GS-10s Customize function, you can rely on your own sensibilities and create a totally new effect by tweaking the settings for the Preamp/Speaker Simulator, Overdrive/Distortion, and Pedal Wah. The result can then be saved on the GS-10 as Custom settings. You can also use these custom settings in other patches. Parameter Type Value JC Clean, TW Clean, Crunch, VO Lead, BG Lead, MS1959 Stk, Modern Stk -50+50 -50+50 -50+50 -50+50 -50+50 -50+50
The trademarks listed in this document are trademarks of their respective owners, which are separate companies from BOSS. Those companies are not affiliated with BOSS and have not licensed or authorized BOSSs GS-10. Their marks are used solely to identify the equipment whose sound is simulated by BOSSs GS-10.
Bottom Edge Bass Freq Treble Freq Preamp Low Preamp High
Type
Selects the basic type of preamp. JC Clean TW Clean This is the sound of the Roland JC-120. This models a Fender Twin Reverb. This is a crunch sound that can produce natural distortion. This models the drive sound of a VOX AC-30TB. This models the lead sound of the MESA/Boogie combo amp. This models the sound input to Input I on a Marshall 1959. This models the rhythm channel of a MESA/Boogie Dual Rectifier.
Customizing the COSM Amps

You can make three different sets of settings, Custom 1, Custom 2, and Custom 3. * The sound of any patch that uses Custom 1, 2, or 3 will be altered if the custom settings are edited. 1. Press the PREAMP/SPEAKER On/Off switch to display the PREAMP/SPEAKER effect screen. 2. Press PARAMETER [ parameter. ][ ] to call up the Type
Crunch VO Lead BG Lead MS1959 Stk Modern Stk
Section 5
Bottom
Adjusts the amount of distortion in the low frequencies.
3. Rotate the PATCH/VALUE dial to call up Custom 1, Custom 2, or Custom 3.

fig.05-010d
Edge
Adjusts the amount of distortion in the high frequencies.
Bass Freq (Bass Frequency)

Adjusts the frequency affected by the BASS knob. 4. Press PARAMETER [ parameters.
fig.05-020d
][
] to show the custom
Treble Freq (Treble Frequency)

Adjusts the frequency affected by the TREBLE knob.
Preamp Low
Adjusts the preamp sections low-frequency tone. 5. Rotate the PATCH/VALUE dial to change the settings value. 6. Repeat Steps 4 and 5 as needed. 7. Press [EXIT] to return to the Play screen.
Preamp High
Adjusts the preamp sections high-frequency tone.
55
Customizing the Speakers

You can make three different sets of settings, Custom 1 and Custom 2. * The sound of any patch that uses Custom 1 or 2 will be altered if the custom settings are edited. 1. Press the PREAMP/SPEAKER On/Off switch to display the PREAMP/SPEAKER effect screen. 2. Press PARAMETER [ Type parameter. ][ ] to call up the SP
Close:
This type of cabinet features an enclosed rear panel.
Customizing Overdrive and Distortion

You can make three different sets of settings, Custom 1, Custom 2, and Custom 3. * The sound of any patch that uses Custom 1, 2, or 3 will be altered if the custom settings are edited. 1. Press the OD/DS On/Off switch to display the OD/DS effect screen. 2. Press PARAMETER [ parameter. ][ ] to call up the Type
3. Rotate the PATCH/VALUE dial to call up Custom 1 or Custom 2.

fig.05-030d
4. Press PARAMETER [ parameters.

fig.05-040d
][

fig.05-050d
5. Rotate the PATCH/VALUE dial to change the settings value. 6. Repeat Steps 4 and 5 as needed. 7. Press [EXIT] to return to the Play screen. Parameter Speaker Size Color Low Color High Speaker Num Cabinet Value 515 -10+10 -10+10 x1, x2, x4, x8 Open, Close

fig.05-060d
][
5. Rotate the PATCH/VALUE dial to change the settings value. 6. Repeat Steps 4 and 5 as needed. 7. Press [EXIT] to return to the Play screen. Parameter Type Value OD-1, OD-2, CRUNCH, DS-1, DS-2, METAL-1, METAL-2, FUZZ -50+50 -50+50 -50+50 -50+50
Speaker Size
Selects the size of speaker.
Color Low
Adjusts the speaker sections low-frequency tone.
Color High
Adjusts the speaker sections high-frequency tone.
Bottom Top Low High
Speaker Num (Speaker Number)

Sets the number of speakers.
Cabinet
Selects the speaker cabinet type.
Open:
This is an open-backed cabinet.
56
Type
Selects the basic type of overdrive/distortion. OD-1 OD-2 CRUNCH DS-1 DS-2 METAL-1 METAL-2 FUZZ This is the sound of the BOSS OD-1. This is the sound of the BOSS OD-2. This is a crunch sound of the BOSS BD-2. This gives a basic, traditional distortion sound. This creates a heavier distortion sound. This is the sound of the BOSS MT-2. This gives a heavy metal sound. This models a FUZZFACE.

fig.05-080d
][
6. Rotate the PATCH/VALUE dial to change the settings value. 7. Repeat Steps 4 and 5 as needed. 8. Press [EXIT] to return to the Play screen. Parameter Type Q Range Low Range High Presence value CRY WAH, VO WAH, Fat WAH, Light WAH, 7String WAH -50+50 -50+50 -50+50 -50+50
Bottom
Adjusts the amount of distortion in the low frequencies.
Top
Adjusts the amount of distortion in the high frequencies.
Low
Adjusts low-frequency tone.
Type
Selects the basic type of wah.
Section 5
High
Adjusts the high-frequency tone. CRY WAH VO WAH Fat WAH Light WAH 7String WAH
Customizing Pedal Wah

You can make three different sets of settings, Custom 1, Custom 2, and Custom 3. * The sound of any patch that uses Custom 1, 2, or 3 will be altered if the custom settings are edited. 1. Press the FX-1 On/Off switch to display the FX-1 effect screen. 2. Press PARAMETER [ ][ ] to call up the FX Select parameter, then select PW with the PATCH/ VALUE dial. 3. Press PARAMETER [ parameter. ][ ] to call up the Type
This models the sound of the CRY BABY wah pedal popular in the `70s. This models the sound of the VOX V846. This a wah sound featuring a bold tone. This wah has a refined smooth sound. Wah featuring a broader range of variations for the seven-string guitar.
Q
Adjusts the amount of characteristic effect applied to the wah tone.
Range Low
Selects the tone produced when the pedal is back.
Range High
Selects the tone produced when the pedal is forward.

fig.05-070d
Presence
Adjusts the tonal quality of the wah effect.
57
Chapter 6 Setting the External Pedal Functions

This section describes the settings required to use an expression pedal or foot switch connected to the EXP PEDAL/CTL1,2 jack on the rear panel.
Setting the External Expression Pedal Functions (Expression Pedal Function)

fig.06-001
If you want the external pedal to have the same function at all times
In situations such as when you want to use the expression pedal only as a volume pedal, you can set the external pedal function as a global setting common to the GS-10 overall. Expression Pedal Function (refer to right) Control 1, 2 Function (p. 59)
If you want the external pedal function to change with the patch
If you want the external pedal to function differently depending on the patch, perhaps using the expression pedal to change the volume in one patch, but using it to adjust the amount of overdrive distortion in another patch, then use the Assign settings. In each patch you can set up to eight different types (Assign numbers) determining which parameter is to be controlled by a particular controller. In addition, you can use the Assign function to set controllers using Control Change messages from external MIDI devices. Assign (p. 60)
1
]
1. Press [SYSTEM], then press PARAMETER [ [ ] so that EXP PDL Func is displayed.
fig.07-110d
2. Rotate the PATCH/VALUE dial to set the expression pedal function.
Auto:
Normally used as a foot volume pedal. When Pedal Wah (p. 36) or Pedal Bend (p. 45) is switched on, the expression pedal automatically switches to the pedal wah or pedal bend function. When Pedal Wah and Pedal Bend are switched off, the pedal automatically operates as a foot volume pedal.
When using an expression pedal or foot switch with the Assign settings, set the Expression pedal Function or Control 1 or 2 Function setting to Assign 1-8.
Assign 1-8:
Used as the controller set in the Assign (p. 60) for each patch.
Foot Volume:
Used as a foot volume pedal.
Patch Level:
Used as a patch level controller.
Pedal Wah:
Used as a pedal wah when Pedal Wah is on.
Pedal Bend:
Used as a pedal bend when Pedal Bend is on. 3. Press [EXIT] to return to the Play screen.
58
Setting the External Foot Switch Functions (Control 1, 2 Function)

* When connecting two foot switches using the special optional Roland PCS-31 connector cord, the foot switch connected with the white-banded plug functions according to the Control 1 function settings, and the foot switch connected with the redbanded plug functions according to the Control 2 function settings. * When you have only one foot switch connected, the Control 1 function settings are used.
fig.06-002
Direct Patch Up:

The direct patch (p. 18) number increases by 1 each time the foot switch is pressed.
Direct Patch Down:

The direct patch (p. 18) number decreases by 1 each time the foot switch is pressed.
Patch Up:
The patch (p. 18) number increases by 1 each time the foot switch is pressed.
Patch Down:
The patch (p. 18) number decreases by 1 each time the foot switch is pressed.
Patch Level Inc1:

The patch level (p. 54) value increases by 10 each time the foot switch is pressed.
Patch Level Inc2:

The patch level (p. 54) value increases by 20 each time the foot switch is pressed.
Patch Level Dec1:

The patch level (p. 54) value decreases by 10 each time the foot switch is pressed.
Patch Level Dec2:

The patch level (p. 54) value decreases by 20 each time the foot switch is pressed.
1. Press [SYSTEM], then press PARAMETER [ ] [ ] so that CTL 1 Func or CTL 2 Func is displayed.
fig.07-120d
Section 6
2. Rotate the PATCH/VALUE dial to set the foot switch function.
Assign 1-8:
The controller set in each patchs Assign (p. 60) is used.
Tuner On/Off:
The foot switch is used as a tuner On/Off switch. Use a momentary-type foot switch (such as the optional FS-5U).
Remote Strt/Stop:
Used as a foot switch for use in starting and stopping a computer or a recorder, sequencer, or other MIDIconnected device. For more on the settings for the device being run, refer to Controlling Recorders and Sequencers Remotely from the GS-10 (Remote Control) (p. 75).
59
Setting the External Pedal Function for Individual Patches (Assign)

There are two ways to set the assignments, Quick Settings, which allows you to use [QUICK FX] to complete the settings quickly and easily, and Manual Settings, where each parameter is set one at a time.
5. Turn the PATCH/VALUE dial to select the Preset settings. 6. To use the Quick Settings with other Assigns, repeat Steps 25. Even when using this procedure, the settings selected in Step 5 are maintained as is and carried over to the Quick Settings for the next effect. 7. To save the settings, use the Write procedure (p. 25).
Quick Settings
When you use [QUICK FX] to select prepared settings (Preset settings), the relevant parameters are then instantly set to their optimal values. This lets you finish making the settings simply, instead of setting each individual parameter separately.
fig.06-010
Press [EXIT] to return to the Play screen.
Preset Settings
P01 PEDAL WAH P02 PEDAL BEND The expression pedal functions as a wah pedal. The expression pedal is used for pedal bend. The expression pedal functions as a volume pedal. The compressor is switched on and off with the foot switch. The overdrive/distortion is switched on and off with the foot switch. The delay is switched on and off with the foot switch. The chorus is switched on and off with the foot switch. FX-1 is switched on and off with the foot switch. FX-2 is switched on and off with the foot switch. The foot switch is used for tap input of the delay time. The foot switch is used for tap input of the Master BPM. The foot switch is used for switching the preamp/speaker channel select (A B C A ...).
P03 FOOT VOLUME P04 COMP ON/OFF P05 OD/DS ON/OFF P06 DELAY ON/OFF P07 CHRUS ON/OFF
1,3
1. Press [ASSIGN].
P08 FX-1 ON/OFF P09 FX-2 ON/OFF ] to select one of the P10 DLY TIME TAP P11 MSTR BPM TAP P12 CH SEL INC
2. Press PARAMETER [ ][ Assigns from Assign 18.
3. Press [ASSIGN] to set the selected Assign to On. Each time [ASSIGN] is pressed it alternately switches this on and off. ASSIGN flashes in the display when the Assign is switched off. * Always set any Assign to Off when it is not being used. 4. Press [QUICK FX]. The Preset settings selection screen appears in the display.
fig.06-011d
* The foot switch function is enabled for the foot switch connected to CTL 1.
* The following appears when the Quick Settings are changed through editing of parameters immediately after the patches are changed.
fig.06-012d
60
Manual Settings
Here, you can individually determine which controller is to control which parameter.
fig.06-013
7. To use other Assigns, repeat Steps 26. Even when using this procedure, the settings selected in Step 6 are maintained as is and carried over to the Quick Settings for the next effect. 8. To save the settings, use the Write procedure (p. 25). Press [EXIT] to return to the Play screen.
5 2,4
Target
fig.06-040d
This sets the parameter to be affected. The parameters that you can select as the target are shown below.
1,3
1. Press [ASSIGN]. 2. Press PARAMETER [ ][ Assigns from Assign 18. ] to select one of the
Effect On/Off Effects Parameters

Switches on/off the effect indicated in the screen and controls the effects parameters.
MST: Patch Level

Controls the patch volume.
3. Press [ASSIGN] to set the selected Assign to On. Each time [ASSIGN] is pressed it alternately switches this on and off. ASSIGN flashes in the display when the Assign is switched on. * Always set any Assign that is not going to be used to Off. 4. Press PARAMETER [ following screens.
fig.06-020d
MST: Master BPM

Controls the Master BPM.
TUNER On/Off
Turns the tuner on and off.
Section 6
][
] to display the
Master BPM(Tap)
Controls the Master BPM using tap input.
Target
Delay Time(Tap)
Controls the delay time using tap input.
Target value range: Min
Remote Strt/Stop
Starts and stops the recorder, sequencer, or other such device connected to the GS-10.
Target value range: Max
Patch Level Inc1

Source
Increases the patch volume level in increments of 10 units.
Source Mode
Patch Level Inc2

Increases the patch volume level in increments of 20 units.
Active Range Low
Patch Level Dec1

Decreases the patch volume level in increments of 10 units.
Active Range High
Patch Level Dec2

Decreases the patch volume level in increments of 20 units.
5. Rotate the PATCH/VALUE dial to change the settings value. 6. Repeat Steps 4 and 5 as needed.
CH Select Inc
Switches the preamp channel in the following order: A B C A...
CH Select Dec
Switches the preamp channel in the following order: C B A C...
61
* Although you can set this so that the same target is controlled by more than one controller, in such cases, make sure not to have different sources changing the parameter at the same time. Changing the parameter simultaneously using different sources may result in noise being generated.
When using the expression pedal:

fig.06-070
maximum value Target Max
Target Range
fig.06-050d
minimum value Target Min

When the pedal is fully raised When the pedal is fully advanced
Expression Pedal
The value of the parameter selected as the target changes within the range defined by Min and Max, as set on the GS-10. When using an external foot switch, or other controller that acts as an on/off switch, Min is selected with Off (CLOSED), and Max is selected with On (OPEN). When using an external expression pedal or other controller that generates a consecutive change in the value, the value of the setting changes accordingly, within the range set by the minimum and maximum values. Also, when the target is of an on/off type, the median value of the received data is used as the dividing line in determining whether to switch it on or off.
When controlling the On/Off target with the expression pedal:

fig.06-080
On Target Max
On Off Target Min
Off
When the pedal When the pedal When the pedal is fully raised is advanced halfway is fully advanced
Expression Pedal
When using the foot switch:

fig.06-060
* The range that can be selected changes according to the target setting. * When the minimum is set to a higher value than the maximum, the change in the parameter is reversed. * The values of settings can change if the target is changed after the minimum and maximum settings have been made. If youve changed the target, be sure to recheck the minimum and maximum settings.
Amount of change in parameter value maximum value Target Max
minimum value Target Min Off On Release Depress Foot Switch
62
Source
fig.06-090d
Active Range
fig.06-110d
This sets the controller (source) that affects the target parameter. Controllers that can be selected as the source are shown below. This sets the operational range within which the value of the setting changes when an expression pedal or other controller that changes the value consecutively is used as the source. If the controller is moved outside the operational range, the value does not change, it stops at minimum or maximum.
EXP PEDAL
Expression pedal connected to the EXP PEDAL/CTL 1, 2 jack.
CTL 1, CTL 2
Foot switch connected to the EXP PEDAL/CTL 1, 2 jack.
(Example) With Act. Range Lo: 40, Act. Range Hi: 80

fig.06-120
MIDI CC# 131, 6495

Control Change messages from an external MIDI device (1 31, 6495)
maximum value
Target Max
Source Mode
fig.06-100d
minimum value
Target Min
40
80
127
This determines whether the control pedal will function as a momentary type switch (such as the optional FS-5U).
Act.Range Act.Range Lo Hi
fig.06-130
Section 6
Normal
The normal state is Off (minimum value), with the switch On (maximum value) only while the foot switch is depressed.
On
Toggle
The setting is toggled On (maximum value) or Off (minimum value) with each press of the foot switch. * Set this to Normal when a latch-type foot switch (such as the optional FS-5L) is connected, or when selecting something other than a foot switch as the controller.
Off 0 Off 40
Act.Range Lo
On
60 80 127 Center Act.Range Hi value
* When using a foot switch or other on/off switching controller as the source, leave these at Lo: 0 and Hi: 127. With certain settings, the value may not change.
63
Chapter 7 Convenient Functions and System Settings

Tuning the Guitar
When the Tuner is turned on, sounds input to the GS-10 are output directly as is (bypassed), and the tuner is activated. Under these conditions you can then tune your guitar.
How to Tune
1. Play a single open note on the string being tuned. The name of the note closest to the pitch of the string that was played appears in the display. * Only play a single note on the one string being tuned.
Turning the Tuner Function On

fig.07-010
2. Tune the string until the string name appears in the display. 7th B A# A 6th E D# D 5th A G# G 4th D C# C 3rd G F# F
Regular 1/2 Step Down 1 Step Down
2nd B
A# A
1st E D# D
3. As you watch the Tuning Guide, adjust the guitars tuning until appears in the center. 4. Repeat Steps 13 until all of the strings are tuned. Each time [TUNER] is pressed, the Tuner is switched on or off. The [TUNER] buttons indicator lights when the function is on. * When tuning guitars equipped with a tremolo bar, when one string is tuned, the others may end up being out of tune. In this case, tune to the pitch indicated by the initial note name, then tune the other strings again, repeatedly fine-tuning each string.
About the Display During Tuning

With the GS-10s internal tuner, the note name is indicated in the upper row of the display and the Tuning Guide is shown in the lower row, indicating the difference between the input sound and the sound in the display.
fig.07-020d
Changing the Tuner Settings

You can change the following tuner-related settings.
Changing the Reference Pitch (435445 Hz)

fig.07-040d
Note Name
Tuning Guide
When the difference from the correct pitch falls within 50 cents, the Tuning Guide then indicates the size of that difference. As you watch the Tuning Guide, tune the guitar so that the appears in the center.
fig.07-030
The frequency of A4 (the middle A on a piano keyboard) played by an instrument (such as a piano) that provides the pitch to which the other instruments refer in tuning before a performance begins is called the reference pitch. You can set the reference pitch on the GS-10 from 435 to 445 Hz. * This is set to 440 Hz when shipped from the factory.
Too High
Setting the Output Used During Tuning

fig.07-050d
Tuned
Too Low
This selects the output while Tuner is on.
Mute:
Sounds are muted, and no sound is output.
64
Bypass:
Sounds input to the GS-10 bypass the processing and are output directly as is. * This is set to Bypass when shipped from the factory.
fig.07-060
Adjusting the Display Contrast (LCD Contrast)

Depending on where the GS-10 is placed, the display may become difficult to read. If this occurs, adjust the display contrast. 1. Press [SYSTEM] a number of times until LCD Contrast is displayed. * You can also select this by pressing [SYSTEM], and then pressing PARAMETER [ ][ ].
fig.07-070d
5 1,5
1. Press [TUNER], causing the indicator to light. 2. Press PARAMETER [ ][ ] until you have either Tuner Pitch or Tuner Output displayed. 3. Rotate the VALUE dial to change the settings. 4. Repeat Steps 2 and 3 to change each parameters settings. 5. Press [TUNER] or [EXIT] to return to the Play screen.
2. Rotate the PATCH/VALUE dial to adjust the contrast. Valid Settings: 116 3. Press [EXIT] to return to the Play screen.
Limiting the Patches That Can Be Switched (Patch Extent)

By setting an upper limit to the patches, thus limiting the range of patches that can be switched, you can set the GS-10 so that only the patches you need can be selected. 1. Press [SYSTEM], then press PARAMETER [ [ ] so that Patch Extent is displayed.
fig.07-080d
Switching Tuner On and Off with the External Pedal You can use an external pedal (such as the FS-5U) connected to the EXP PEDAL CTL 1,2 jack to switch the tuner on and off. Use the Assign (p. 60) settings to set the following to one of the Assigns in ASSIGN 18. Target: Target Min: Target Max: Source: Mode: Act. Range Lo: Act. Range Hi: TUNER On/Off On Off CTL1 (or CTL2) Toggle 0 1127
Section 7
2. Rotate the PATCH/VALUE dial to set the upper limit for the patches. Valid Settings: U001U100, P101P200 3. Press [EXIT] to return to the Play screen.
65
Keeping the Same Pedal Operations When Switching Patches (Assign Hold)
This setting determines whether or not the Assigns (p. 60) operational status is carried over to the next patch when patches are switched. * Assign Hold does not function if the Assign Source mode is set to Toggle (whereby the value is toggled between Min and Max each time the pedal is pressed). 1. Press [SYSTEM], then press PARAMETER [ [ ] so that Assign Hold is displayed.
fig.07-090d
Setting the Knob Functions (Knob Mode)

This sets the way the values of settings are changed when the control knobs are turned. 1. Press [SYSTEM], then press PARAMETER [ [ ] so that Knob Mode is displayed.
fig.07-100d
] 2. Rotate the PATCH/VALUE dial to set the Knob mode.
Immediate:
Turning the knobs immediately changes the values. 2. Rotate the PATCH/VALUE dial to set Expression Pedal Hold.
Current Setting:
Values begin to change only once the knob position reaches the values set in the patch. 3. Press [EXIT] to return to the Play screen.
On: The Assign status is carried over. (Example)

If a patch is switched while the volume is being controlled with the expression pedal, the volume of the subsequent patch will take on the value determined by the current pedal position (angle). If the patch switched to has the expression pedal controlling the wah effect, then the volume assumes the value set in the patch, and the patchs wah effect is given the value derived from the current pedal position (angle).
Off: The Assign status is not carried over.

(Example) If a patch is switched while the volume is being controlled with an expression pedal, the volume of the subsequent patch is set to the value set in that patch. If the expression pedal is operated, and that information is transmitted to the GS-10, the volume will change in accord with the pedals movement. 3. Press [EXIT] to return to the Play screen.
66
Checking the Effect Output Level with the Level Meter

You can meter the output level of each effect. This is handy for checking the effects output levels.
fig.07-130
3
1. Press [METER].
fig.07-140d
2. Rotate the PATCH/VALUE dial to select the effect whose level you want to check. * Effects are shown in lowercase letters when turned off. * You can check the level of signals being input to the INPUT jack by selecting Input. Selecting Output allows you to check the level of signals output from the GS-10. * You may not be able to achieve the effects you envision if your output levels are set too high. Adjust the output level of each of your effects to the optimum value while checking the meter and making sure the needle doesnt swing too far to the right. 3. Press [EXIT] to return to the Play screen.
Section 7 67
Chapter 8 Using the GS-10 with External MIDI Devices Connected

The GS-10s MIDI operations are altered when the GS-10 and the computer are connected via USB. Also refer to Chapter 9 Using USB to Connect a Computer (p. 78) when making these connections.
Remotely Controlling the GS-10 Using an External MIDI Device

Switching Patch Numbers
When the GS-10 receive Program Change messages from the external MIDI device, its patches are simultaneously switched.
Operations Using MIDI

You can perform the following operations using MIDI with the GS-10. * The use of MIDI requires that the MIDI channels of the connected devices match. If the MIDI channel settings are not correct, the GS-10 will be unable to exchange data with other MIDI devices. You can set up the correspondence between MIDI Program Change messages and the GS-10s patches using the Program Change Map (p. 73). You may need to work on these correspondences when you want to line up some effects in combination with other MIDI devices. The connections shown in the figure below are for a sequencer automatically performing the backing as a guitar is being played. The patches are switched automatically when the program numbers corresponding to the patches are input along with the performance data at the points where you have determined the GS-10 patches are to be switched.
fig.08-020
Operating From the GS-10

Outputting Program Change Messages
When a patch is selected on the GS-10, a Program Change message corresponding to the patch number is transmitted simultaneously. The external MIDI device then switches its settings according to the Program Change message it receives.
fig.08-010
MIDI IN MIDI OUT
MIDI OUT MIDI IN
Outputting Control Change Messages

Data describing the actions of the external devices connected to the EXP PEDAL/CTL 1,2 jack are output as Control Change messages. Such messages can be used to (among other things) manipulate the parameters of an external MIDI device.
Receiving Control Change Messages

You can control specified parameters during a performance by having the GS-10 receive Control Change messages.
Parameters to be controlled are set with Assign (p. 60).
Transmitting Data
You can use Exclusive messages to transmit the settings for effect sounds and other content stored in the GS-10 to other MIDI devices. For example, you can provide another GS-10 with the same settings, and save effect sound settings to a sequencer or other device.
Receiving Data
The GS-10 can receive data transmitted from another GS-10, as well as data thats been stored on a sequencer.
68
Making the Settings for MIDI Functions

Here is a description of the GS-10s MIDI functions. Set them as needed, depending on the intended use. 1. Press [SYSTEM] a number of times until the following screen appears.
fig.08-030d
TX Channel (Transmit Channel)

Valid Settings: 116, Rx
fig.08-060d
This sets the MIDI Transmit channel used for transmitting MIDI messages. When set to Rx, this MIDI channel is same as the MIDI Receive channel. * This is set to Rx when shipped from the factory.
Device ID
2. Press PARAMETER [ ][ ] so that the parameter that you want to set appears in the display. 3. Rotate the PATCH/VALUE dial to change the settings value. 4. Repeat Steps 2 and 3 as needed. 5. Press [EXIT] to return to the Play screen. This sets the Device ID used for transmitting and receiving Exclusive messages. * This is set to 17 when shipped from the factory. Valid Settings: 132
fig.08-070d
RX Channel (Receive Channel)

Valid Settings: 116
fig.08-040d
Sync Clock
Valid Settings: Auto, Internal
fig.08-080d
This sets the MIDI channel used for receiving MIDI messages. * This is set to 1 when shipped from the factory.
You can synchronize the performance of a sequencer or other external MIDI device.
Omni Mode
Valid Settings: Omni Off, Omni On
fig.08-050d
Auto:
When the MIDI Clock of the external MIDI device is not being received, the performance is synchronized to the tempo set in MASTER BPM; when the external MIDI devices MIDI Clock is being received, the performance is synchronized to that.
Section 8
When set to Omni On, messages are received on all channels, regardless of the MIDI channel settings. * Even when Omni Mode is set to ON, the only Exclusive messages received are for Device ID data set with Device ID. * This is set to Omni On when shipped from the factory.
Internal:
The performance is synchronized to the tempo set in Master BPM. * This is set to Auto when shipped from the factory. * When you have an external MIDI device connected, the Master BPM is then synchronized to the external MIDI devices tempo, thus disabling the Master BPM setting. To enable setting of the Master BPM, set to Internal. * When synchronizing performances to the MIDI Clock signal from an external MIDI device, timing problems in the performance may occur due to errors in the MIDI Clock.
69
Remote Ctrl (Remote Control)

Valid Settings: Standard, Advanced, MMC This setting determines the MIDI messages transmitted when a MIDI sequencer or other external MIDI device is controlled with a foot switch or other controller connected to the GS-10.
fig.08-090d
Off:
Program Change messages are not output, even when patches are switched.
On:
Program Change messages are simultaneously output when patches are switched. * This is set to On when shipped from the factory.
Standard:
System Realtime messages are transmitted.
EXP PDL Out (Expression Pedal Out)

Valid Settings: Off, 131, 3395
fig.08-120d
Advanced:
System Realtime messages and Note messages are transmitted.
MMC:
MIDI Machine Control is transmitted. * For more details, refer to Controlling Recorders and Sequencers Remotely from the GS-10 (Remote Control) (p. 75). * This is set to Advanced when shipped from the factory.
This sets the controller number when expression pedal operation data is output as Control Change messages. When set to Off, Control Change messages are not output. * This is set to CC# 7 when shipped from the factory.
CTL1 Out (Control 1 Out)

fig.08-130d
KnobCtl Out (Knob Control Out)

Valid Settings: Off, On
fig.08-100d
This setting determines whether or not the information describing the knob adjustments is output as System Exclusive messages.
This sets the controller number when operation data from the external pedal connected to the CTL 1 jack is output as Control Change messages. When set to Off, Control Change messages are not output. * This is set to Off when shipped from the factory.
Off:
Knob operations are not output as System Exclusive messages.
CTL2 Out (Control 2 Out)

fig.08-140d
On:
Knob operations are output as System Exclusive messages. * This is set to On when shipped from the factory. This sets the controller number when operation data from the external pedal connected to the CTL 2 jack is output as Control Change messages. When set to Off, Control Change messages are not output. * This is set to Off when shipped from the factory.
PC Out (Program Change Out)

Valid Settings: Off, On
fig.08-110d
This setting determines whether or not Program Change messages are output when patches are switched on the GS10.
70
Transmitting and Receiving Settings Data

On the GS-10, you can use Exclusive messages to provide another GS-10 with identical settings, and save effect settings on a sequencer or other device. Transmitting data this way is called Bulk Dump, while receiving such data is referred to as Bulk Load.
When Transmitting Data to Another GS-10

Connect as shown in the figure below, and match the Device ID for the transmitting and receiving devices.
fig.08-160
Transmitting Data to an External MIDI Device (Bulk Dump)

The following types of data can be transmitted. You can transmit data by specifying the range from the start to the end of transmission. Displayed System Data Transmitted System Parameters, Harmonist scales, Auto Riff phrases, and Preamp, Overdrive/Distortion, and Wah Custom Edit parameter settings Settings for Patch Number U001 through U100 Settings for the patch the is currently called up
MIDI IN MIDI OUT
U001U100 Temp
Transmitting
fig.08-170

When Saving to a MIDI Sequencer
Connect as shown in the figure below, and put the sequencer in the state where it is ready to receive Exclusive messages.
fig.08-150
1,2
4 3
MIDI IN MIDI OUT
1 Section 8
1. Press [SYSTEM], then press PARAMETER [ ] [ ] so that MIDI:Bulk Dump is displayed.

fig.08-170d
2. Press PARAMETER [ ][ ] to move the cursor, and rotate the PATCH/VALUE dial to select the start and end of the data to be transmitted. * For instructions on operating the sequencer, refer to the owners manual for the sequencer you are using. 3. When the data to be sent has been determined, press [WRITE]. The data is transmitted.
71
fig.08-180d
fig.08-210d
When the transmission is completed, the screen prior to transmission returns to the display. 4. Press [EXIT] to return to the Play screen.
The following appears in the display when the GS-10 finishes receiving the data.
fig.08-220d
Receiving Data from an External MIDI Device (Bulk Load)

When Receiving Data Saved on a MIDI Sequencer
Connect as shown below. Set the GS-10s Device ID to the same number that was used when the data was transmitted to the MIDI sequencer.
fig.08-190
At this stage, even more data can be received. 3. Press [EXIT] to quit Bulk Load. After you press [EXIT], the Play screen returns to the display.
MIDI OUT MIDI IN
* For instructions on operating the sequencer, refer to the owners manual for the sequencer you are using.
Receiving
1. Press [SYSTEM], then press PARAMETER [ [ ] so that MIDI:Bulk Load is displayed.
fig.08-200d
2. Transmit the data from the external MIDI device. The following appears in the display when the GS-10 receives the data.
72
Setting the Program Change Map

When switching patches using Program Change messages transmitted by an external MIDI device, you can freely set the correspondence between Program Change messages received by the GS-10 and the patches to be switched to in the Program Change Map.
fig.08-230
3 1,4
Initial Program Change Map Settings

The Program Change Map set at the factory is shown below. Program Change Bank Program Select Number 1 2 3 : : 98 0 99 100 101 102 : 128 1 2 3 : : 98 1 99 100 101 102 : 128
Patch Number U001 U002 U003 : : U098 U099 U100 U100 U100 : U100 P101 P102 P103 : : P198 P199 P200 P200 P200 : P200
1. Press [SYSTEM], then press PARAMETER [ ] [ ] so that MIDI:Map Select is displayed.

fig.08-240d
2. Rotate the PATCH/VALUE dial to select Program. * You cannot set the Program Change Map when Fix is selected (it is not displayed). * See below for more on MID Map Select. 3. Press PARAMETER [ appears in the display.
fig.08-250d
] until MIDI:Program Map
Bank Select Number
Program Number
Patch Number
4. Press PARAMETER [ ][ ] to move the cursor, and rotate the PATCH/VALUE dial to set the received Program number and the corresponding patch number. * Use this same procedure to select Bank Select Numbers. * When using only Program Change messages to make program changes, without using Bank Select messages, set the Program number (1-128) when the Bank Select number is 0. 5. Repeat Step 4 as needed, setting patch numbers to their corresponding Program numbers, until the Program Change Map is completed. 6. Press [EXIT] to return to the Play screen.
Section 8
73
Enabling/Disabling the Program Change Map Settings (MIDI Map Select)

This setting determines whether patches are switched according to the Program Change Map settings, or to the default settings. 1. Press [SYSTEM], then press PARAMETER [ ] [ ] so that MIDI:Map Select is displayed.
fig.08-260d
Changing Patch Numbers on an External MIDI Device From the GS-10

When patches are switched with the GS-10, a Program Change message is transmitted. The correspondence between the GS-10s initial bank and patch numbers and the transmitted Program Change messages is shown in the table below. Program Change Bank Program Select Number 1 2 3 : 0 : 98 99 100 1 2 3 : 1 : 98 99 100
Patch Number U001 U002 U003 : : U098 U099 U100 P101 P102 P103 : : P198 P199 P200
2. Rotate the PATCH/VALUE dial to select Fix or Prog.
Fix:
Switches to the patches according to the default settings. For more on the default settings, refer to Initial Program Change Map settings (p. 73).
Prog:
Switches to the patches according to the Program Change Map. 3. Press [EXIT] to return to the Play screen.
74
Controlling Recorders and Sequencers Remotely from the GS-10 (Remote Control)
If you have a MIDI-controllable recorder, sequencer, or other such external MIDI device connected to the GS-10, you can connect a foot switch to the EXP PEDAL CTL 1,2 jack and use it for remote control of the external MIDI device.
Use the software to set the operations to be performed by means of these Note messages. * Settings examples are given on p. 76 and p. 77. Please refer to these examples. STOP START 90 00 00 90 02 01 90 02 00 90 00 00 FC 90 00 00 90 04 01 90 04 00 90 00 00 FA
Setting the Messages Used for Controlling Devices

The GS-10 features three kinds of messages (MIDI messages) that are used for controlling external MIDI devices, and you can select messages in accordance with the connected device.
fig.08-270
About Note Messages

When START is activated, the following messages are output.
fig.08-281
Note# 00 On
Note# 04 On
Note# 04 Off
Note# 00 Off
Note Messages for Assigning Functions: Note#04 (E -1)
Note Messages for Remote Control: Note#00 (C -1)
Messages are similarly output for Reset/Stop/Play/Rec. The following shows the correspondence between the functions and the Note messages used in assigning them. Note# 05 02 04 07
Reset Stop Play Rec
Note Name (Key) F -1 D -1 E -1 G -1
1. Press [SYSTEM] a number of times, then press PARAMETER [ ][ ] so that MIDI:Remote Ctrl is displayed.
fig.08-280d
* The note name (Key) may differ depending on the application used and the settings; you may wish to refer to the relevant manual for details.
* Note messages are transmitted over the selected transmission channel (p. 69). 2. Use the PATCH/VALUE dial to select the message according to the connected external MIDI device.
When set to MMC

MIDI Machine Control is transmitted. STOP START F0 7F 7F 06 01 F7 F0 7F 7F 06 02 F7
Section 8
When set to Standard

MIDI System messages are transmitted. STOP START FC FA
When set to Advanced

Some computer applications allow recording and playback functions such as Start and Stop to be assigned to specified MIDI messages. When this setting is selected, Note messages used in sending commands for remote control to the application and Note messages for assigning various functions are transmitted together with the Standard messages.
75
Controlling the Device Remotely

Make the connections as shown below.
fig.08-280
With the GS-10, you can control external MIDI devices by combining [EXIT] and DIRECT PATCH [1][4].
fig.08-300
Reset
Stop
Play
Rec
MIDI IN MIDI OUT EXP PEDAL / CTL 1,2
The Reset, Stop, Play, and Rec functions are assigned to DIRECT PATCH [1][4]. When you press these buttons while holding down [EXIT], the messages corresponding to the MIDI: Remote Ctrl setting are transmitted.
When MIDI: Remote Ctrl is set to Standard

MIDI System messages are transmitted. Reset Stop Play Rec No function FC FA No function
* Neither FA nor FC can be transmitted consecutively. * For more on the operation of the connected device, refer to the owners manual for the device you are using.
When MIDI: Remote Ctrl is set to Advanced

Some computer applications allow recording and playback functions such as Start and Stop to be assigned to specified MIDI messages. When set to this setting, Note messages used in assigning functions are transmitted in addition to the Standard messages. Use the software to set the operations to be performed by means of these Note messages. Reset Stop Play Rec 90 00 01 90 00 01 90 00 01 90 00 01 90 05 01 90 02 01 90 04 01 90 07 01 90 05 00 90 02 00 90 04 00 90 07 00 90 00 00 90 00 00 FC 90 00 00 FA 90 00 00
Setting
1. Follow the instructions in Setting the Messages Used for Controlling Devices (p. 75) to set the messages that are to be used for remote control. 2. Press [SYSTEM] a number of times, then press PARAMETER [ ][ ] so that SYS:CTL1 Func (or SYS:CTL2 Func) is displayed.
fig.08-290d
* Neither FA nor FC can be transmitted consecutively. * Note messages are transmitted over the selected transmission channel (p. 69). * If connecting only one foot switch, set the GS-10 so that SYS:CTL1 Func is indicated; if connecting two foot switches, set the GS-10 so that SYS:CTL1 Func or SYS:CTL2 Func is indicated for the corresponding foot switch. 3. Rotate the PATCH/VALUE dial to select Remote Strt/ Stop. * For more on SYS:CTL1 Func (or SYS:CTL2 Func), refer to p. 59. 4. Press [EXIT] to return to the Play screen. Each time the foot switch is pressed, it alternately sends Start and Stop.
When set to MMC

MIDI Machine Control is transmitted. Reset Stop Play Rec F0 7F 7F 06 44 06 01 00 00 00 00 00 F7 F0 7F 7F 06 01 F7 F0 7F 7F 06 02 F7 F0 7F 7F 06 06 F7
76
Settings Example: When Using SONAR 2.0

The following settings allow you to control the sequencer Play/Stop, Reset, and Record functions from the GS-10. (With SONAR 2.0, these are set according to note names (Keys) rather than Note messages.) 1. From the Options menu, choose MIDI Devices. 2. In the MIDI Devices dialog box, select [BOSS GS10 Control] as both the Inputs and Outputs. 3. From the Options menu, choose Key Bindings. 4. Make the following settings in the Key Bindings dialog box. [Type of Keys] Check MIDI and Enable [MIDI Shift Options] Check Key, and input C -1 5. In the [Bindings] area, set [Key] to [D -1]. 6. In the [Function] area, select [Transport | Stop]. 7. Click the [Bind] button. The [Key] [D -1] will be connected to the [Function] area [Transport | Stop]. 8. In the [Bindings] area, set [Key] to [E -1]. 9. In the [Function] area, select [Transport | Play]. 10. Click the [Bind] button. The [Key] [E -1] will be connected to the [Function] area [Transport | Play]. 11. In the [Bindings] area, set [Key] to [F -1]. 12. In the [Function] area, select [Transport | Reset]. 13. Click the [Bind] button. The [Key] [F -1] will be connected to the [Function] area [Transport | Reset]. Reset Stop Play Rec 14. In the [Bindings] area, set [Key] to [G -1]. 15. In the [Function] area, select [Transport | Record]. 16. Click the [Bind] button. The [Key] [G -1] will be connected to the [Function] area [Transport | Record]. Repeat Steps 516 so that the following settings are created. Note # 05 02 04 07 Key F -1 D -1 E -1 G -1 Function Transport | Reset Transport | Stop Transport | Play Transport | Record
17. Click the [OK] button to finish making settings. The Key Bindings dialog box will close, and the settings will be completed.
Section 8 77
Chapter 9 Using the GS-10 Connected to a Computer Via USB

Before Connecting with USB
With the GS-10, you can use USB to transmit both digital audio signals and MIDI messages between the GS-10 and your computer. This requires installation of a USB driver on your computer so that it can work with the GS-10s driver mode settings. For instructions on installing the driver, please read Installing & Setup the USB Driver (p. 91).
fig.09-009
Setting USB-Related Functions

Adjusting the Recording Level (Output Level)
This adjusts the volume level of the digital audio output to the USB and DIGITAL OUT connectors. 1. Press [USB]. 2. Press PARAMETER [ displayed.
fig.09-010d
][
] so that Out Levl is
Computer
3. Rotate the PATCH/VALUE dial to set the output level. 4. Press [EXIT] to return to the Play screen.
Adjusting the Playback Volume Level (Input Level)

This adjusts the volume level of the digital audio input from the USB connector.
Driver Mode
The GS-10 features two operational modes, one mode that uses the special driver on the CD-ROM included with the GS-10 and another mode that uses the operating systems (Windows/Mac OS) standard drivers. The special driver provides high-quality sound and stable timing for audio recording, playback, and editing. In addition, the driver enables you to control the GS-10 with MIDI messages and connect external MIDI devices to your computer.
1. Press [USB]. 2. Press PARAMETER [ Level is displayed.

fig.09-020d
][
] so that Input
3. Rotate the PATCH/VALUE dial to set the input level. 4. Press [EXIT] to return to the Play screen.
78
Enabling and Disabling the Direct Monitor Command

This setting determines whether or not the command (the Direct Monitor command) controlling the Direct Monitor (described later) setting is enabled. 1. Press [USB]. 2. Press PARAMETER [ displayed.fig.
09-021d
Off:
Set this to Off if transmitting audio data internally through a computer (Thru). * This is set to On when shipped from the factory. * If you are using the special driver, you can control Direct Monitor On/Off from ASIO 2.0-compatible application such as Cubase. 4. Press [EXIT] to return to the Play screen.
][
] Monitor Cmd is
Setting the Output Mode

This selects whether the output is in stereo or if the effect sound and direct sound are output separately. 3. Use the PATCH/VALUE dial to enable or disable the command. 1. Press [USB]. 2. Press PARAMETER [ Mode is displayed.
fig.09-031d
Disable:
The Direct Monitor command is disabled, maintaining the Direct Monitor mode set by the GS-10.
][
] so that Output
Enable:
The Direct Monitor command is enabled, allowing the Direct Monitor mode to be switched from an external device. * This is set to Disable when shipped from the factory. 4. Press [EXIT] to return to the Play screen. 3. Rotate the PATCH/VALUE dial to set the output mode.
Stereo (L/R):
Sounds are output in stereo.
Effect/Direct:
The effect sound and direct sound are output separately and independently. * This is set to Stereo (L/R) when shipped from the factory. 4. Press [EXIT] to return to the Play screen.
Switching the Output Signals (Direct Monitor)

This setting determines whether or not the effect sound is output by the GS-10s speakers or at the PHONES, OUTPUT L/R, or GUITAR AMP OUT jacks. 1. Press [USB]. 2. Press PARAMETER [ Monitor is displayed.
fig.09-030d
][
] so that Dir
Section 9
3. Rotate the PATCH/VALUE dial to set On or Off.
On:
The effect sound is output. Set this to On when using the GS-10 as a standalone device, without connecting to a computer (no sound will be output if this is set to Off).
79
Switching the Driver Mode

After first installing both the special and standard drivers and then switching the GS-10s driver mode, you can switch between the special driver and the standard driver to use the one you need. For more on installing the drivers, refer to Installing & Setup the USB Driver (p. 91). 1. Press [USB]. 2. Press PARAMETER [ Mode is displayed.
fig.09-040d
MIDI in Standard Driver Mode

Normally, its better to use MIDI in the Advanced driver mode. * With the factory settings, the Standard driver mode is compatible only with audio. If Standard is selected as the driver mode with an OS standard driver that is compatible with both audio and MIDI data, you can use both audio and MIDI with the standard driver by making the following settings. * It has been confirmed that standard Windows XP/2000/Me/98 and Mac OS X/9/8 drivers are not supported or that problems may occur due to their use. 1. Press [USB]. 2. Press PARAMETER [ Func is displayed.
fig.09-050d
][
] so that Driver
][
] so that Std.Drv
3. Rotate the PATCH/VALUE dial to set the driver mode.
Standard:
The standard OS USB driver is used in this mode.
Advanced:
The special driver on the included CD-ROM is used in this mode. * This is set to Advanced when shipped from the factory. 4. Press [EXIT] to return to the Play screen. * If the driver for the set mode has not yet been installed, at this point you need to turn off the power to the GS-10 and install the driver. 5. Quit any sequencer software and any other computer applications used by the GS-10. 6. Switch off the GS-10, then turn it on again. The corresponding driver is installed on the computer. 3. Rotate the PATCH/VALUE dial to set the standard driver function.
Audio:
Only audio is used.
Audio&MIDI:
Both audio and MIDI are used. 4. Press [EXIT] to return to the Play screen. 5. Quit any sequencer software and any other computer applications used by the GS-10. 6. Turn off the power to the GS-10, and then turn the unit on again. * For more on installing the drivers, refer to Installing & Setup the USB Driver (p. 91).
80
Recording the GS-10s Output with a Computer

Set your application (such as a sequencer) so that the audio input port it uses is the GS-10. You can freely set the point in the signal chain from which to extract the signal to be sent to the computer with Effect Chain (p. 24). For example, by setting this so that the computer records the signals as they are at the beginning of the chain, you can record the sounds without any effects added while you listen to the performance with the effects applied from the speakers. If you are using the software to send the audio data through, set Direct Monitor (p. 79) to Off.
Running the GS-10 from a Computer

You can use USB MIDI to run the GS-10 from your computer. When you set the GS-10 to the Advanced driver mode (p. 92, p. 112), the MIDI connectors used for operation of the GS-10 switches from MIDI IN/OUT connectors to the USB drivers GS-10 Control MIDI ports. Set your editor and sequencer MIDI input and output ports to GS-10 Control. For more on MIDI-related settings, refer to Chapter 8 Using the GS-10 with External MIDI Devices Connected (p. 68).
Using the GS-10 As a MIDI Interface

When the GS-10 is set to the Advanced driver mode (p. 92, p. 112) and connected via USB, you can use the GS-10s MIDI IN and OUT connectors to connect your computer to external MIDI devices. Set the input and output ports used for the computers MIDI applications to GS-10 MIDI In/Out.
Applying Effects with the GS-10 to a Computers Audio Playback

Set the audio output port used by applications to the GS-10. You can use the GS-10 to add effects to audio data played back from the computer, and then record these sounds back to the computer. Use this feature when you want to add effects to existing audio data. 1. Press [INPUT SELECT].
fig.09-060d
2. Use the PATCH/VALUE dial to select one of the following settings.
USB (Gtr/Mic):
Effects are applied to guitar and vocal sounds from the computer.
USB (Bass):
Effects are applied to bass sounds from the computer. 3. Press [EXIT] to return to the Play screen. The flow of audio signals at this point is shown in the figure on p. 19, p. 20.
Section 9
In this mode, set the software so that audio is not transmitted through (not set to Thru).
81
Appendices
About MIDI
MIDI is an acronym for Musical Instrument Digital Interface, and is a world-wide standard for allowing electronic musical equipment to communicate by transmitting messages such as performance information and sound selections. Any MIDI equipped device is able to transmit applicable types of data to another MIDI equipped device, even if the two devices are different models or were made by different manufacturers. In MIDI, performance information such as playing a key or pressing a pedal are transmitted as MIDI Messages. MIDI has sixteen channels 116, and MIDI messages will be received by the instrument (the receiving device) whose channel matches the channel of the transmitter. * If omni mode is on, data of all MIDI channels will be received regardless of the MIDI channel setting. If you do not need to control a specific MIDI channel, you may set Omni On.
Main types of MIDI message used by the GS-10

MIDI includes many types of MIDI messages that can convey a variety of information. MIDI messages can be broadly divided into two types; messages that are handled separately by MIDI channel (channel messages), and messages that are handled without reference to a MIDI channel (system messages).
How MIDI messages are transmitted and received

First, we will explain briefly how MIDI messages are transmitted and received.
MIDI connectors
The following types of connector are used to convey MIDI messages. MIDI cables are connected to these connectors as needed.
fig.10-010
Channel messages
These messages are used to convey performance information. Normally these messages perform most of the control. The way in which a receiving device will react to each type of MIDI message will be determined by the settings of the receiving device.
Program change messages

These messages are generally used to select sounds, and include a program change number from 1 to 128 which specifies the desired sound. The GS-10 also allows you to select any of the 200 different patch numbers in conjunction with bank select messages; a type of control change message.
MIDI IN MIDI OUT MIDI THRU
This connector receives messages from another MIDI device. This connector transmits messages from this device. This connector re-transmits the messages that were received at MIDI IN.
Control change messages

These messages are used to enhance the expressiveness of a performance. Each message includes a controller number, and the settings of the receiving device will determine what aspect of the sound will be affected by control change messages of a given controller number. The specified parameters can be controlled with the GS-10.
* The GS-10 features both MIDI IN and MIDI OUT connectors.
MIDI channels
MIDI is able to independently control more than one MIDI device over a single MIDI cable. This is possible because of the concept of MIDI channels. The idea of MIDI channels is somewhat similar to the idea of television channels. By changing channels on a television set, you can view a variety of programs. This is because the information of a particular channel is received when the channels of the transmitter and receiver match.
fig.10-020
System messages
System messages include exclusive messages, messages used for synchronization, and messages used to keep a MIDI system running correctly.
Exclusive messages
Exclusive messages handle information related to a units own unique sounds, or other device-specific information. Generally, such messages can only be exchanged between devices of the same model by the same manufacturer. Exclusive messages can be employed to save the settings for effects programs into a sequencer, or for transferring such data to another GS-10. The two instruments must be set to the same device ID numbers when exchanging SysEx messages.
Broadcasting Station A Broadcasting Station B Broadcasting Station C
T.V. information from many different broadcasting station is sent through an antena.
Select the channel of the broadcasting station you wish to watch
82
Appendices
About the MIDI implementation

MIDI allows a variety of messages to be exchanged between instruments, but it is not necessarily the case that all types of message can be exchanged between any two MIDI devices. Two devices can communicate only if they both use the types of messages that they have in common. Thus, every owners manual for a MIDI device includes a MIDI Implementation Chart. This chart shows the types of message that the device is able to transmit and receive. By comparing the MIDI implementation charts of two devices, you can tell at a glance which messages they will be able to exchange. Since the charts are always of a uniform size, you can simply place the two charts side by side.
fig.10-030
Error Messages
If you attempt an incorrect operation or if an operation could not be executed, the display will indicate an error message. Refer to this list and take the appropriate action.
fig.10-060d
The memory backup battery inside the GS-10 has run down. (This message will appear when the power is turned on.) Replace the battery as soon as possible. For battery replacement, please contact a nearby Roland service center or your dealer.
Fold here MIDI Device A

Function Transmit Recognized Remarks
MIDI Device B
fig.10-070d
There is a problem with the MIDI cable connection. Check to make sure the cable has not been pulled out or is not shorted.
On the supplied GS-10 Software CD-ROM disc you can find the MIDI Implementation document (Imp_E.pdf). This document provides detailed descriptions of all the functions that the GS-10 is capable of offering when communicating using MIDI. * In order to read Imp_E.pdf, you will need Adobe Acrobat Reader.
fig.10-080d
More MIDI messages were received in a short time than could be processed correctly.
fig.10-081d
About USB
USB, short for Universal Serial Bus, is an interface for connecting peripheral equipment to computers. Using USB, you can connect a variety of peripherals using a single USB cable and transfer data rapidly. It also allows peripheral devices to be connected or disconnected while the power is left on, while the computer automatically recognizes when this occurs (some devices may require settings or other procedures). With the GS-10, you can use MIDI to transfer MIDI messages and audio data. You are attempting to change the following PREAMP/ SPEAKER (p. 28) parameter settings with OUTPUT SELECT (p. 16) set to something other than Line/ Phones: SP Type, Mic Type, Mic Dis., Mic Pos., Mic Level, Direct Level The settings may be changed, but they have no effect.
Appendices 83
Appendices
Patch List
No. P101 P102 P103 P104 P105 P106 P107 P108 P109 P110 P111 P112 P113 P114 P115 P116 P117 P118 P119 P120 P121 P122 P123 P124 P125 P126 P127 P128 P129 P130 P131 P132 P133 P134 P135 P136 P137 P138 P139 P140 P141 P142 P143 P144 P145 P146 P147 P148 P149 P150 Patch Name POWER LEAD WARM CLEAN BRIT VALVES METAL MASTERS ATTIC AMPS WARM OVERDRIVE 1969 VIBE CLASSICAL ROCK 5th TONE+SlwGEAR CRYING 70's FUNK ALMOST HUMAN 80's ROCKABILLY H&K TRIPLE TEXAS TREM JAZZ CATS DRIVIN' BG BIGGEST MUFF CLEAN + DRIVE SOLID STACK CRUNCH ROTARY CLASSIC TRIO OC + FUZZ 3 CHANNEL TWIN CREAMED MS1959 CRUNCHY STRAT FLANGE ME OUT! DS-1 STANDARD DOTTED 8th DELAY FAT CRUNCH!! FEEDBACK FRETLESS SOLO 1968-80 for LP GS-PAD HARMONYMAN in Am NATURAL CRUNCH HUM->ACOUSTIC HARD ROCK70s-90s HEAVY RIFF HiGAIN BG LEAD HIT E5 CHORD JAZZY CHORD LP LOUD,LDR,LOUDEST CLASSIC DUDE LEGATO MASTER MAGIC JC MATCH ROCK MELLOW HOLLOW MELTDOWN METALIZER OD/DS T-Scream '60s FUZZ T-Scream GUV DS Blues OD MUFF FUZZ Turbo OD Booster MUFF FUZZ Blues OD Distortion Natural OD Booster T-Scream Ch. Select A A A A A A A A A A A A A A A B A A A A A A A A A A A A A A A A A C A A C A A A A A A A A A A A A A ch-A MS1959(I) Warm Clean VO Drive T-Amp Lead Pro Crunch Fat MATCH MS1959(I) Pro Crunch Warm Clean MS1959(I) Clean TWIN Clean TWIN Warm Clean T-Amp Clean Warm Clean Jazz Combo BG Rhythm JC-120 Warm Clean Power Stack Crunch Clean TWIN MS1959(I) Clean TWIN Wild Crunch Warm Clean Clean TWIN MS1959(I) Warm Clean Wild Crunch Crunch Mic Preamp VO Drive Full Range Warm Clean Blues Full Range MS HiGain R-FIER Vint BG Rhythm MS1959(I+II) Warm Clean MS1959(I) JC-120 Clean TWIN JC-120 MATCH Drive Warm Clean JC-120 Clean TWIN ch-B Drive Stack Warm Clean MS1959(I) R-FIER Red Clean TWIN Crunch MS1959(I) MS1959(I) JC-120 MS1959(II) Clean TWIN Crunch Pro Crunch T-Amp Crunch Clean TWIN Pro Crunch BG Drive Full Range MATCH Drive Power Stack Crunch MS1959(I+II) BG Lead Clean TWIN MS1959(I+II) Clean TWIN Crunch Drive Stack Tweed Fat MATCH R-FIER Red BASS 360 MS1959(I) Clean TWIN Wild Crunch T-Amp Clean Full Range BG Lead R-FIER Orng BG Drive SLDN Jazz Combo Power Stack VO Drive Smooth Drive JC-120 Fat MATCH Crunch Fat MATCH 5150 Drive ch-C Metal Lead JC-120 MS HiGain 5150 Drive VO Lead VO Drive Power Stack MS HiGain SLDN MS HiGain Clean TWIN BG Lead Drive Stack T-Amp Lead Pro Crunch SLDN R-FIER Orng Pro Crunch Smooth Drive Power Stack Crunch R-FIER Red Power Stack Clean TWIN MS1959(II) Pro Crunch Smooth Drive Drive Stack Full Range SLDN R-FIER Red Warm Clean MS1959(I) Warm Clean MS1959(I+II) Drive Stack Full Range 5150 Drive R-FIER Red BG Lead BG Drive JC-120 R-FIER Orng VO Lead T-Amp Lead MS HiGain Fat MATCH Smooth Drive MS1959(I) Metal Lead
84
Appendices
No. P151 P152 P153 P154 P155 P156 P157 P158 P159 P160 P161 P162 P163 P164 P165 P166 P167 P168 P169 P170 P171 P172 P173 P174 P175 P176 P177 P178 P179 P180 P181 P182 P183 P184 P185 P186 P187 P188 P189 P190 P191 P192 P193 P194 P195 P196 P197 P198 P199 P200
Patch Name MORPHEOUS MS TRI-CHANNEL MODERN CRUNCH MONO SYNTH CLEAN&COMPRESSED DRIVE1964-65-69 OCTAVE SYN LEAD OLD MS w/JUMPER SLICE IT UP! OCTAVE T-WAH RHODES GUITAR PINK WALL POWER CHORD ORCHESTRAL DELAY ROCK ON DOWN 2 D TRIPLE CLEAN R-FIRED UP REAL TWEED SINGLE->ACOUSTIC SMOOTH LEAD SNAPPY WAH ST CRUNCH AMB SUPER CLEAN SCOOP! SEMI-HOLLOW SMOOTH SOLO STRICTLY STRAT OCTAVE FUZZ SUPER NATURAL AUSTIN + HOUSTON MOVING IN SYNC SWAMP for ST TON O'METAL TREM-VIBRATO 5th MONO DRONE CLN,CRUNCH&TWEED ROCK RHYTHM BASSFACE PLAY E.ACOUSTIC PIEZO->Ac.GUITAR VOCAL HARMO[Mic] FINGERED [Bass] PICK DRIVE[Bass] FUNK SLAP [Bass] ENHANCED [Bass] FRETLESS [Bass] TRIPLE 810[Bass] OC HiGAIN [Bass] B-MANIAC [Bass] DI CLEAN [Bass]
OD/DS Metal Zone Blues OD Turbo OD Blues OD Oct FUZZ Oct FUZZ -
Ch. Select C A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A C A A A A A A A A A A
ch-A Full Range MS1959(I) T-Amp Clean JC-120 Clean TWIN VO Drive Mic Preamp MS1959(I) BG Rhythm Clean TWIN Warm Clean MATCH Drive Crunch Clean TWIN Warm Clean Warm Clean R-FIER Orng Tweed Mic Preamp Smooth Drive Warm Clean Fat MATCH Mic Preamp Crunch Clean TWIN Smooth Drive Warm Clean Pro Crunch Warm Clean Warm Clean Pro Crunch Pro Crunch R-FIER Red Clean TWIN Warm Clean Clean TWIN Warm Clean CONCERT 810 Mic Preamp Full Range Mic Preamp FLIP TOP SESSION Bass Clean SESSION BASS 360 CONCERT 810 T. E. B-MAN Mic Preamp
ch-B MATCH Drive MS1959(I) T-Amp Clean Blues Clean TWIN VO Lead Mic Preamp MS1959(II) Clean TWIN BG Lead Warm Clean MATCH Drive MATCH Drive Crunch Pro Crunch Pro Crunch R-FIER Orng Tweed Full Range Smooth Drive Blues Crunch Mic Preamp T-Amp Lead Clean TWIN Smooth Drive Clean TWIN Clean TWIN Mic Preamp Clean TWIN Tweed Tweed Drive Stack VO Drive Clean TWIN Pro Crunch MS1959(I) Bass Crunch Full Range Full Range Clean TWIN T. E. BASS 360 T. E. Bass Clean Mic Preamp CONCERT 810 B-MAN B-MAN Mic Preamp
ch-C R-FIER Vint MS HiGain T-Amp Lead SLDN BG Lead Clean TWIN Mic Preamp MS1959(I+II) SLDN 5150 Drive Warm Clean MATCH Drive Fat MATCH VO Drive MS HiGain T-Amp Clean R-FIER Red Tweed Warm Clean Smooth Drive T-Amp Lead VO Drive JC-120 5150 Drive Clean TWIN Smooth Drive Pro Crunch Pro Crunch JC-120 BG Rhythm BG Drive MS1959(I) MS HiGain Power Stack MS1959(I+II) Tweed MS1959(I) Bass HiGain JC-120 Full Range MS HiGain BASS 360 Bass Crunch SESSION T. E. T. E. CONCERT 810 Bass HiGain B-MAN Bass Clean
Appendices
* With the factory settings, the content of the User patches is the same as that of the Preset patches. * Patches with [Mic] appended to the name are for use with mics. Sound from the GUITAR/BASS jack wont be heard. * Patches with [Bass] appended to the name are for use with basses.
85
Appendices
Restoring the Factory Settings (Factory Reset)

Restoring the GS-10 to the settings made at the factory is referred to as Factory Reset. Not only can you return all of the settings to the values in effect when the GS-10 was shipped from the factory, you can also specify the range of settings to be reset.
fig.10-040
Factory Settings
Tuner
Tuner Pitch: Tuner Output: Output Select OUTPUT Select: A= 440 Hz Bypass Line/Phones
2 + POWER
Direct Patch
Direct Patch 1/2/3/4: U001/U002/U003/U004
System
LCD Contrast: Patch Extent: Assign Hold: Knob Mode: EXP PDL Func: CTL1 Func: CTL2 Func: 16 P200 On Immediate Auto Assign 1-8 Assign 1-8
4
1. Turn off the power. 2. While holding down PREAMP/SPEAKER CHANNEL SELECT [A] and [B], turn on the power. The Factory Reset range setting screen appears in the display.
fig.10-050d
MIDI
RX Channel: Omni Mode: TX Channel: Device ID: Sync Clock: Remote Ctrl: KnobCtrlOut: PC Out: EXP PDL Out: CTL1 Out: CTL2 Out: Map Select: 1 Omni On Rx 17 Auto Advanced On On CC#7 Off Off Fix
Factory Reset range
* To cancel Factory Reset, press [EXIT]. 3. Press PARAMETER [ ][ ] to move the cursor, and rotate the PATCH/VALUE dial to specify the range of settings you want to restore to factory settings.
USB
Output Level: Input Level: Monitor Cmd: Dir Monitor: Output Mode: Driver Mode: Std.Drv Func: 100 100 Disable On Stereo (L/R) Advanced Audio
System:
System parameters, Harmonist scales, Auto Riff phrases, and Preamp/Speaker, Overdrive/Distortion, and Wah Custom Edit parameter settings.
U001U100:
Settings for Patch Number U001 through U100. 4. If you want to proceed with the factory reset, press [ENTER]. The specified range of data will be returned, and return to the Play screen.
Others
Speaker ON/OFF: Mic Gain: ON 50
86
Appendices
MIDI Implementation Chart
GUITAR EFFECTS SYSTEM with USB AUDIO INTERFACE Model GS-10

Function...
Date: Jul. 15, 2003 Version: 1.00

Remarks Memorized
MIDI Implementation Chart

Transmitted 116 116 X X ************** X ************** X X X X X 0, 32 131 3363 6495 O (01) O O O 116 116 OMNI ON/OFF X X X X X X X X X O O X O *1 *2 *2 Bank Select Recognized
Basic Channel
Default Changed Default Messages Altered True Voice Note ON Note OFF Key's Ch's
Memorized
Mode
Note Number : Velocity After Touch Pitch Bend
Control Change
Prog Change
: True #
O ************** O X X X X O X X X X X X
*1 00H:
O 0127 O X X X O X X X X X O X
Program Number 1128
System Exclusive System Common System Real Time : Song Pos : Song Sel : Tune : Clock : Command
: All sound off : Reset All Controller : Local ON/OFF : All Notes OFF : Active Sense : Reset
Aux Message
Notes
*2
For values of 01H or lower, the Program Change Map will be switched according to the value. For values of 02H or higher, the received data will be ignored. 20H: The received data will be ignored, regardless of the value. Rcognizes messages designated by specifying this as a source (p. 63) for Assign.
Appendices
On the supplied GS-10 Software CD-ROM disc you can find the MIDI Implementation document (Imp_E.pdf). This document provides detailed descriptions of all the functions that the GS-10 is capable of offering when communicating using MIDI. (In order to read Imp_E.pdf, you will need Adobe Acrobat Reader.)
Mode 1 : OMNI ON, POLY Mode 3 : OMNI OFF, POLY
Mode 2 : OMNI ON, MONO Mode 4 : OMNI OFF, MONO
O : Yes X : No
87
Appendices
Specifications
GS-10: Guitar Effects System with USB Audio Interface
Rated Power Output
1.5 W + 1.5 W
Connectors
GUITAR/BASS input jack PHONES jack MIC INPUT jack (TRS balanced, 1/4 inch phone type) MIC INPUT connector (XLR balanced) AUX INPUT jack L/R (RCA Phono type) OUTPUT jack L/R (RCA Phono type) GUITAR AMP OUT jack EXP PEDAL/CTL 1,2 jack DIGITAL OUT connector (Coaxial) USB connector MIDI connector IN/OUT AC Adaptor jack
Signal Processing
AD Conversion: 24 bit + AF method DA Conversion: 24 bit Digital Out/USB Audio: 24 bit
Sampling Frequency
44.1 kHz
Program Memories
200: 100 (User) + 100 (Preset)
Nominal Input Level

GUITAR/BASS INPUT: -10 dBu MIC INPUT: -40 dBu (BALANCE) AUX INPUT L/R: -10 dBu
Control
(PREAMP/SPEAKER) GAIN knob BASS knob MIDDLE knob TREBLE knob PRESENCE knob LEVEL knob On/Off button CHANNEL SELECT button A/B/C (COMP) SUSTAIN knob On/Off button (OD/DS) DRIVE knob LEVEL knob On/Off button (DELAY) FEEDBACK knob LEVEL knob On/Off button TAP button (CHORUS) LEVEL knob On/Off button (REVERB) LEVEL knob On/Off button
Input Impedance
GUITAR/BASS INPUT: 1 M MIC INPUT: 2.2 k AUX INPUT L/R: 33 k
Nominal Output Level

OUTPUT L/R: -10 dBu GUITAR AMP OUT: -10 dBu
Output Impedance
OUTPUT L/R: 1 k GUITAR AMP OUT: 1.5 k
Speaker
Internal Speaker x 2
Digital Output
EIAJ CP1201, S/P DIF
USB
AUDIO IN/OUT: Stereo, 44.1 kHz, 24 bit (Capable of simultaneous recording and playback) MIDI Control IN/OUT MIDI IN/OUT
Display
16 characters, 2 lines (backlit LCD)
88
Appendices
FX-1 button FX-2 button EQ button NAME/NS/MASTER button ASSIGN button INPUT SELECT button QUICK FX button PARAMETER button L/R EXIT button WRITE button TUNER button USB button SPEAKER ON/OFF button METER button SYSTEM button DIRECT PATCH button 14 AUX INPUT LEVEL knob OUTPUT LEVEL knob PATCH/VALUE dial AF Method (Adaptive Focus method) This is a proprietary method from Roland that vastly improves the signal-to-noise (S/N) ratio of the A/D and D/A converters. In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
Power Supply
AC 14 V; Supply AC adaptor (BOSS BRC series)
Current Draw
800 mA
Dimensions
329 (W) x 231 (D) x 85 (H) mm 13 (W) x 9-1/8 (D) x 3-3/8 (H) inches
Weight
2.25 kg/5 lbs
Accessories
AC Adaptor (BRC series) Read This First (Leaflet) Owners Manual USB cable GS-10 Software CD-ROM Cakewalk Music Creator set (CD-ROM, Owners Manual)
Options
Expression Pedal: EV-5 (Roland) Foot Switch: FS-5U Connection Cord: PCS-31 (Roland) (1/4 inches Phone Plug (stereo) 1/4 inches Phone Plug (mono) x 2) * 0 dBu= 0.775 Vrms
Appendices 89
MEMO
90
Installing & Setup the USB Driver

In order to use the GS-10 USB, you must first install the USB driver. The USB Driver is included in the GS-10 SOFTWARE CD-ROM.
What is USB Driver?

The USB Driver is software which passes data between the GS-10 and the application (sequencer software etc.) that is running on the USB-connected computer. The GS-10 Driver sends data from the application to the GS-10, and passes data from the GS-10 to the application. The GS-10 can receive and transmit both digital audio signals and MIDI messages.
Application USB connector USB Driver
USB cable
Computer
GS-10
The explanation about installing and setup the driver is organized according to the computer and driver mode that you are using. Please proceed to the following pages.
Installing & Setting Up the Driver (Windows) ............................... (p. 92) Installing & Setting Up the Driver (Macintosh) ........................... (p. 112)
91
Installing & Setting Up the Driver (Windows)

Special Driver and Standard Driver
The GS-10 features two operational modes, each of which uses a different type of driver, with one mode using the special driver on the CD-ROM included with the GS-10 and the other mode using the standard Windows driver. Before installing the drivers, you must first switch the GS-10s driver mode. For instructions on switching the GS-10s driver modes, refer to Switching the Driver Mode (p. 80).
Special Driver
Special Driver mode allows audio to be recorded/played/edited with high quality and stable timing. Audio signals can be transferred between the GS-10 and the computer at a resolution of 24 bits and sampling frequencies of 44.1 kHz. And in addition to audio, you can also control the GS-10 using MIDI messages and connect external MIDI devices and computers. Select this mode if you are using an application that allows high-quality audio recording/playback/ editing, such as an application that supports 24 bit audio (e.g., the Cakewalk series or Cool Edit) or an ASIO-compatible application (e.g., Cubase VST, Logic Audio, or SingerSongWriter). Installing the special driver (p. 93)
Standard Driver
In Standard Driver mode, audio signals are transferred between the GS-10 and the computer at a resolution of 16 bits and sampling frequencies of 44.1 kHz. Select this mode if you are using an application that uses Windows own functionality, such as an application that uses the computers CD-ROM drive to play back CD-audio, or an application that uses the software synthesizer included with Windows. Installing the OS-standard driver (p. 102) * If you want to use MIDI, use special driver mode. * The standard driver included with Windows does not support ASIO.
92
Installing the special driver

The installation procedure will differ depending on your system. Please proceed to one of the following sections, depending on the system you use.
Windows XP/2000 users................ (p. 93) Windows Me/98 users ................. (p. 101)
1. 2. 3.
Windows XP/2000 users

Windows XP
With the GS-10 disconnected, start up Windows.
Disconnect all USB cables except for a USB keyboard and USB mouse (if used). If you are using Windows XP Professional, you must log on using a user name with an administrative account type (e.g., Administrator).
Open Control Panel from the Windows Start menu, then open the System Properties dialog. Click Hardware tab, and then click [Driver Signing].
Open the Driver Signing Options dialog box.
fig.11-020
Depending on how your system is set up, the System icon may be displayed directly in the Control Panel (the Classic display). In this case, double-click the System icon.
4.
Make sure that What action do you want Windows to take? is set to Ignore.
If currently set to Warn or Block, set it to Ignore here, then after installing the driver, restore the original setting.
5. 6.
Click [OK] to close the System Properties dialog box. Exit all currently running software (applications).
Also close any open windows. If you are using virus checking or similar software, be sure to exit it as well.
7. 8.
Insert the CD-ROM into the CD-ROM drive of your computer. Click the Windows start button. From the menu that appears, select Run....
Open the Run... dialog box.
93
9.
In the dialog box that appears, input the following into the Open field, and click [OK].
D:\DRIVER\USB_XP2k\SETUPINF.EXE * The drive name D: may be different for your system. Specify the drive name of your CD-ROM drive.
fig.11-030
In this manual, the location of folders and files is given in terms of the file path, using \ as the delimiter. For example, WinXP_2k\SETUPINF.EXE indicates the SETUPINF.EXE file found in the WinXP_2k folder.
The SetupInf dialog box will appear, with Ready to install the driver appearing in the box.
fig.11-040
10. 11. 12.
Before connecting the USB cable, switch the GS-10s driver mode to Advanced.
For instructions on switching the GS-10s driver modes, refer to Switching the Driver Mode (p. 80).
With the power switch turned OFF, use the USB cable to connect the GS-10 to your computer. Make sure that the GS-10s OUTPUT LEVEL is set to the lowest setting, then switch ON the POWER switch.
The Found New Hardware Wizard will appear.
fig.11-050
Turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to other devices.
This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally.
13.
Make sure that the screen indicates BOSS GS-10, select Install from a list or specific location (Advanced), and click [Next].
The screen will indicate Please choose your search and installation options.
94
fig.11-060
14.
Select Dont search. I will choose the driver to install, and click [Next].
fig.11-070
15.
Make sure that the Model field indicates BOSS GS-10, and click [Next].
Driver installation will begin.
If the What action do you want Windows to take? setting in step 4 was not set to Ignore, a Hardware Installation dialog box will appear.
fig.11-080
If the [Continue Anyway] button appears, click the [Continue Anyway] button to continue with the installation. If you are unable to continue, click [STOP Installation] or [OK] to begin the driver installation over again from Step 1.
The Insert Disk dialog box will appear.

fig.11-090
The Insert Disk dialog may not appear. In that case, proceed to step 17.
16.
Click [OK].
The Files Needed dialog box will appear.
95
17.
Input the following into the Copy files from field, and click [OK].
D:\DRIVER\USB_XP2k
* The drive name D: may be different for your system. Specify the drive name of your CD-ROM drive.
fig.11-100
If the What action do you want Windows to take? setting in step 4 was not set to Ignore, a Hardware Installation dialog box will appear.
fig.11-110
If the [Continue Anyway] button appears, click the [Continue Anyway] button to continue with the installation.
The Found New Hardware Wizard will appear.

fig.11-120
18.
Verify that BOSS GS-10 is displayed, and click [Finish].

Wait until Found New Hardware appears near the taskbar. When driver installation has been completed, the System Settings Change dialog box will appear.
19.
Click [Yes].
Windows will restart automatically.
Next, you need to make the driver settings (p. 107).
96
Windows 2000
1. 2.

Disconnect all USB cables except for a USB keyboard and USB mouse (if used).
Click the Windows Start button, and from the menu that appears, select Settings | Control Panel. In Control Panel, double-click the System icon.
The System Properties dialog box will appear.
fig.11-130
If the GS-10 is already connected to your computer and a message of Add New Hardware Wizard is displayed, go to the included CD-ROM folder named DRIVER\USB_XP2k, open the file Readme_e.htm, and read the Troubleshooting section entitled You attempted to install using the above procedure, but were not able to.
You must log on using a user name with an administrative account type (e.g., Administrator).
3.
Click the Hardware tab, and then click [Driver Signature].

Open the Driver Signing Options dialog box.
fig.11-140
4.
the File signature verification is set to Ignore, and click [OK].

If currently set to Warn or Block, set it to Ignore here, then after installing the driver, restore the original setting.
5. 6.
Click [OK] to close the System Properties dialog box. Exit all currently running software (applications).
7. 8.
97
9.
D:\DRIVER\USB_XP2k\SETUPINF.EXE * The drive name D: may be different for your system. Specify the drive name of your CD-ROM drive.
fig.11-150
In this manual, the location of folders and files is given in terms of the file path, using \ as the delimiter. For example, WinXP_2k\SETUPINF.EXE indicates the SETUPINF.EXE file found in the WinXP_2k folder.
The SetupInf dialog box will appear, with Ready to install the driver appearing in the box.
fig.11-160
10. 11. 12.
If the File signature verification setting in step 4 was not set to Ignore, a Digital Signature Not Found dialog box will appear.
fig.11-170
If the [Yes] button appears, click the [Yes] button to continue with the installation. If you are unable to continue, click [No] or [OK] to begin the driver installation over again from Step 1. If the Insert Disk dialog box does not appear, please read The Insert Disk dialog box does not appear (p. 133)
The Insert Disk dialog box will appear.
98
fig.11-180
13. 14.
Click [OK].
The Files Needed dialog box will appear.
In the Copy files from field, type the folder name that is shown in the dialog box, and click [OK].
D:\DRIVER\USB_XP2k
* The drive name D: may be different for your system. Specify the drive name of your CD-ROM drive.
fig.11-190
If the File signature verification setting in step 4 was not set to Ignore, a Digital Signature Not Found dialog box will appear.
fig.11-200
Click [Yes], and continue the installation.
The Find New Hardware Wizard may be displayed.

fig.11-210
99
15.
Verify that BOSS GS-10 is displayed, and click [Finish].

Driver installation will begin. When driver installation has been completed, the System Settings Change dialog box will appear.
fig.11-220
16.
Click [Yes].
Windows will restart automatically.
100
1. 2.
Windows Me/98 users

Disconnect all USB cables except for a USB keyboard and USB mouse (if used). If the GS-10 is already connected to your computer and a message of Add New Hardware Wizard is displayed, go to the included CD-ROM folder named DRIVER\USB_XP2k, open the file Readme_e.htm, and read the Troubleshooting section entitled You attempted to install using the above procedure, but were not able to.
Exit all currently running software (applications).

3. 4. 5.
D:\DRIVER\USB_ME98\SETUPINF.EXE * The drive name D: may be different for your system. Specify the drive name of your CD-ROM drive.
fig.11-230
In this manual, the location of folders and files is given in terms of the file path, using \ as the delimiter. For example, ME98\SETUPINF.EXE indicates the SETUPINF.EXE file found in the ME98 folder.
The SetupInf dialog box will appear, with Ready to install the driver appearing in the box. * If a message prompting you to restart Windows appears, restart Windows in accordance with the message instructions, then proceed to the following step.
fig.11-240
6. 7. 8.
The driver is installed automatically.
9.
Click [OK].
* If a message prompting you to restart Windows appears, restart Windows in accordance with the message instructions.
101
Installing the OS-standard driver

Windows XP/2000 users.............. (p. 102) Windows Me users ....................... (p. 103) Windows 98 users........................ (p. 104)
1. 2.


3. 4. 5.
Before connecting the USB cable, switch the GS-10s driver mode to Standard.
The GS-10 will be detected automatically, and the driver will be installed.
6.
When installation is complete, restart Windows.
102
1. 2.
Windows Me users

Also close any open windows. If you are using virus checking or similar software, be sure to exit it as well. Turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to other devices.
3. 4. 5.
Windows will detect the GS-10, and the Add New Hardware Wizard dialog box will appear.
fig.11-260
6.
Make sure that Automatic search for a better driver (Recommended) is selected, and click [Next].
Driver detection will begin. When the driver has been found, driver installation will begin. Once the driver has been installed, a dialog box will inform you of this.
fig.11-270
7. 8.
Click [Finish]. Restart Windows.
103
Windows 98 users
The USB composite device driver is installed first, then the USB audio device driver is installed. Use the following procedure to install the drivers.
1. 2.


Also close any open windows. If you are using virus checking or similar software, be sure to exit it as well. Turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to other devices.
3. 4. 5.
USB composite device will be detected automatically, and the Add New Hardware Wizard dialog box will appear.
fig.11-280
6. 7.
Click [Next]. When What do you want Windows to do? appears, select Search for the best driver for your device (Recommended), and click [Next].
fig.11-290
A dialog box like the one shown below will appear.

fig.11-300
104
8.
Check CD-ROM drive, and click [Next].

A dialog box like the one shown below will appear.
fig.11-310
9.
Click [Next]
File (driver) copying will begin.
If the Windows CD-ROM is not inserted in the CD-ROM drive, a Insert Disk dialog box may appear. In this case, insert the Windows CD-ROM into the CD-ROM drive and click [OK].
fig.11-320
When installation of the USB Composite Device driver is completed, a dialog box like the one shown below will appear.
fig.11-330
10.
Click [Finish].
Next, the USB audio device will be detected automatically, and the Add New Hardware Wizard dialog box will appear.
fig.11-340
105
11.
Click [Next], and proceed with the installation in the same way as in steps 810.
When installation of the USB audio device driver is complete, a dialog box like the one shown here will appear.
fig.11-341
12. 13.
Click [Finish].
Installation of the USB composite device driver and USB audio device driver has been completed.
Restart Windows.
106
Driver settings
About the input/output devices
Audio output devices
BOSS GS-10
This sends audio data from the computer to the GS-10. This is the setting you will normally use, such as when using the GS-10 with Media Player. You will also select this setting when using an application such as SONAR in WDM driver mode, or when using a DirectSound application.
MME BOSS GS-10 Out (Windows XP/2000 only)

This sends audio data from the computer to the GS-10. Use this setting if you want to use 24-bit audio with an application that does not have a WDM driver mode or does not support ASIO (such as Cool Edit).
Audio input devices

BOSS GS-10
This receives audio data sent by the GS-10 to the computer. This is the setting you will normally use. You will also select this setting when using an application such as SONAR in WDM driver mode.
MME BOSS GS-10 In (Windows XP/2000 only)

This receives audio data sent by the GS-10 to the computer. Use this setting if you want to use 24-bit audio with an application that does not have a WDM driver mode or does not support ASIO (such as Cool Edit).
ASIO device
If you are using the GS-10 with an ASIO-compatible application such as Cubase, select BOSS GS10 as the ASIO setting on your application. * To prevent an audio oscillation loop or double monitoring, turn monitoring Off in your application, or use ASIO Direct Monitor.
MIDI output devices

BOSS GS-10 MIDI OUT
This transmits MIDI data from the computer to the GS-10. Transmitted MIDI data is output from the GS-10s MIDI OUT connector.
BOSS GS-10 Control

This transmits MIDI data from the computer to the GS-10. You can control the GS-10s operations using MIDI data.
MIDI input devices

BOSS GS-10 MIDI IN
This accepts MIDI data transmitted from the GS-10 to the computer. MIDI data input to the GS-10s MIDI IN connector is transmitted to the computer.
BOSS GS-10 MIDI Control

This accepts MIDI data transmitted from the GS-10 to the computer. Data for the GS-10s operations and performance data is transmitted to the computer.
107
1.
Specifying the audio input/output destination

Windows XP/2000/Me users
Open Control Panel.
Windows XP
1) Click the Windows start button, and from the menu that appears, select Control Panel.
Windows 2000/Me
1) Click the Windows Start button, and from the menu that appears, select Settings | Control Panel. Depending on how your system is set up, the Sounds and Audio Devices icon may be displayed directly in the Control Panel (the Classic view). In this case, double-click the Sounds and Audio Devices icon.
2.
Open the Sounds and Audio Devices Properties dialog box (or in Windows 2000/Me, Sounds and Multimedia Properties).
Windows XP
1) In Pick a category, click Sound, Speech, and Audio Devices. 2) In or pick a Control Panel icon, click the sounds and Audio Devices icon.
Windows 2000/Me
1) In Control Panel, double-click the Sounds and Multimedia icon to open the Sounds and Multimedia Properties dialog box.
3. 4.
Click the Audio tab. For Sound playback, Sound recording, and MIDI music playback, click the located at the right of [Default device] (or in Windows 2000/Me, [Preferred device]), and select the following from the list that appears.
fig.11-350
If the Sound and Multimedia icon is not displayed, click Show all control panel options in the frame at the left.
Special driver mode Sound playback Sound recording MIDI music playback BOSS GS-10 BOSS GS-10 BOSS GS-10 MIDI OUT
Standard driver mode GS-10 (Windows XP), USB Audio Device (Windows 2000/Me) GS-10 (Windows XP), USB Audio Device (Windows 2000/Me) MIDI cannot be handled when using Standard Driver mode. (MIDI in Standard Driver Mode (p. 80))
5.
Click [OK] to close the Sounds and Audio Devices Properties dialog box.
This concludes the procedure for setting the input and output destinations.
Next, set the Windows Volume Control (p. 110).
108
Windows 98 users
1.
Click the Windows Start button, and from the menu that appears, select Settings | Control Panel.
The Control Panel will appear.
2. 3.
In Control Panel, double-click the Multimedia icon. Click the Audio tab.
fig.11-360
4.
Specify the Preferred device.

Click the Playback field and Recording field, make the following selections from the list that appears, and click [Apply]. Special driver mode BOSS GS-10 BOSS GS-10 Standard driver mode USB Audio Device USB Audio Device
Playback Recording
5.
Click the MIDI tab.

fig.11-370
6.
Set MIDI output.

Select [Single instrument], and choose one of the following from the list that appears, and click [Apply]. Special driver mode Standard driver mode MIDI cannot be handled when using Standard Driver mode. (MIDI in Standard Driver Mode (p. 80))
MIDI sound playback
BOSS GS-10 MIDI OUT
7.
Click [OK] to close the Multimedia Properties dialog box.

This concludes the procedure for setting the input and output destinations.
Next, set the Windows Volume Control (p. 110).
109
1.
Volume Control setting

Click the Windows Start button, and select Programs | Accessories | Entertainment | Volume Control.
The Volume Control dialog box will apper.
fig.11-380
If the Volume Control is not installed on your computer, use the Control Panel icon Add or Remove Programs to install it. For details on installation, refer to the Windows manual or Help.
2.
Raise or lower the slider to adjust the volume of the GS-10.

The GS-10 can use the Windows volume control to adjust the output volume.
Items that can be set

CD Player (CD Audio) WAVE Synthesizer SW Synth *1 Controls the volume of audio CDs on the internal CD-ROM drive of the computer. (*1) Controls the volume of sound output from the BOSS GS-10 audio output device. Digital output and analog output will change. Controls the volume of the software synthesizer built into Windows.
If the CD playback volume does not change when you adjust this control, then change the WAVE volume. If you are using Windows 2000 and the CD Player is not displayed, check Enable digital music CDs for this CD playback device in Digital CD Playback. When playing audio CDs from the computers internal CD-ROM drive, or using the GS-10 to play game music (p. 111)
110
When playing audio CDs from the computers internal CD-ROM drive, or using the GS-10 to play game music
Windows XP/2000 users: 1. Open the System Properties dialog box.
Windows XP- Click the Windows start button, and from the menu that appears, select Control Panel. Windows 2000- Select Start | Settings | Control Panel, and in the Control Panel, double-click the System icon.
2. Click the Hardware tab, and click the Device Manager button.
The Device Manager dialog box will apper.
3. In CD-ROM drive, double-click the CD-ROM drive that you are using.
The CD-ROM drives Properties dialog box will appear.
4. Click the Properties tab, then in Digital CD Playback, check the Enable digital CD audio for this CD-ROM device item. Windows Me users: 1. Select Start | Settings | Control Panel, and in Control Panel, doubleclick the System icon.
The System Properties dialog box will appear.
2. Double-click the CD-ROM icon, and then double-click the CD-ROM drive that you are using.
The CD-ROM drives Properties dialog box will appear.
3. Click the Properties tab, then in Digital CD Playback, check the Enable digital CD audio for this CD-ROM device item. Windows 98 users: 1. Select Start | Settings | Control Panel, and in Control Panel, doubleclick the Multimedia icon.
The Multimedia Properties dialog box will appear.
2. Click the Music CD tab, and check the Enable digital CD audio for this CD-ROM device item.
* Depending on your system, playback may still not be possible. For details, please contact the manufacturer of your computer. If you are using a PC-card (PCMCIA) type CD-ROM drive, playing back WAVE data from a CD-ROM or playing an audio CD may cause interrupted sound, or possibly no sound at all.
111
Installing & Setting Up the Driver (Macintosh)

Special Driver and Standard Driver
The GS-10 features two operational modes, each of which uses a different type of driver, with one mode using the special driver on the CD-ROM included with the GS-10 and the other mode using the standard Mac OS driver. Before installing the drivers, you must first switch the GS-10s driver mode. For instructions on switching the GS-10s driver modes, refer to Switching the Driver Mode (p. 80).
Special Driver
In Special Driver mode, allowing audio to be recorded/played/edited with high quality and stable timing. Audio signals can be transferred between the GS-10 and the computer at a resolution of 24 bits and sampling frequencies of 44.1 kHz. And in addition to audio, you can also control the GS-10 using MIDI messages and connect external MIDI devices and computers. Select this mode if you are using an application that allows high-quality audio recording/playback/ editing, such as an application that supports 24 bit audio or an ASIO-compatible application (e.g., Cubase VST, Logic Audio, or Metro). Installing the special driver (p. 112)
Standard Driver
In Standard Driver mode, audio signals are transferred between the GS-10 and the computer at a resolution of 16 bits and sampling frequencies of 44.1 kHz. Select this mode if you are using an application that uses Mac OSs own functionality, such as an application that uses the computers CD-ROM drive to play back CD-audio, or an application that uses the software synthesizer included with Mac OS. Installing the OS-standard driver (p. 123)
* If you want to use MIDI, use special driver mode.
Installing the special driver

Mac OS 9/8 users......................... (p. 112) Mac OS X users ............................ (p. 121)
Mac OS 9/8 users

If using the unit in the Special driver mode, use either OMS or FreeMIDI as the MIDI driver.
The included GS-10 driver is an add-on module for using the GS-10 with OMS or FreeMIDI.
* Either OMS or FreeMIDI must be installed in your Macintosh, as appropriate for the sequencer software you are using.
OMS can be found in the OMS 2.3.8 E folder of the CD-ROM. If you would like to learn more about OMS, refer to OMS_2.3_Mac.pdf in the OMS 2.3.8E folder of the CD-ROM. In order to read OMS_2.3_Mac.pdf, you will need Adobe Acrobat Reader.
112
Disconnect the GS-10 from the Macintosh before you perform the installation.
If the power of the GS-10 is turned on, a message like the following will appear when the Macintosh is started up. Perform the steps described below as appropriate for the message that is displayed. If the screen indicates: Driver required for USB device `unknown device is not available. Search for driver on the Internet? Click [Cancel]. If the screen indicates: Software required for using device `unknown device cannot be found. Please refer to the manual included with the device, and install the necessary software. Click [Cancel].
Use the following procedure to install the GS-10 driver.
1. 2. 3. 4.

If you are using a virus checker or similar software, be sure to exit this as well.
Insert the CD-ROM into the CD-ROM drive. Double-click the GS-10 Driver-E Installer icon (found in the Driver E (Mac OS 9/8) of the CD-ROM) to start up the installer. Verify the Install Location, and click [Install].
* If a message like the following is displayed, click [Continue]. The other currently running applications will exit, and installation will continue.
fig.11-390
The indication for the Install Location will differ depending on your system. Make sure that the startup disk for the system you are using is selected.
A dialog box will indicate Installation completed.
5.
Click [Restart] to restart your Macintosh.
113
OMS settings
If other MIDI devices are connected, you must turn off the power on all devices, and then make OMS settings according to the following procedure. For more on connecting MIDI sound modules, refer to the owners manual for the MIDI sound module you are using.
1. 2. 3. 4.
With the power switch turned OFF, use the USB cable to connect the GS-10 to your computer. Make sure that the GS-10s OUTPUT LEVEL is set to the lowest setting, then switch ON the POWER switch. In the Opcode folder, open the OMS Applications folder, and double-click the OMS Setup icon.
fig.11-400
* The first time OMS is started up, a Create a New Studio Setup dialog box will appear. Click [OK]. If this is the second or later time, select New Studio Setup from the File menu.
fig.11-401
* If the Apple Talk dialog box appears, select [Turn It Off]. Then click [OK] in the dialog box that appears next.
fig.11-410
The OMS Driver Search dialog box will appear.

fig.11-420
114
5. 6.
Click [Search]. When the search has been completed, verify that the OMS Driver Setup dialog box lists the BOSS GS-10, and click [OK].
fig.11-430
* If the dialog box does not show BOSS GS-10, check whether the GS-10 is connected correctly, and start up OMS Setup once again.
7.
Verify that the OMS MIDI Device Setup dialog box lists the GS-10. Then click all check boxes from Port 1 to Port 2 to check them, and click [OK].
A dialog box will appear, allowing you to save the settings in a file.
fig.11-440
* For other connected MIDI devices as well, add a check mark to the port(s) you want to use. For details on settings, refer to the manual that came with your MIDI device. * BOSS/Roland can provide no guarantees or support regarding the operation of MIDI device made by another company. Please contact the manufacturer of your MIDI device.
8. 9.
Input the desired file name, and click [Save]. In the Studio Setup window, change the device name indicating the MIDI device connected to the GS-10 as follows.
Click the device name, and you will be able to edit it. Port 1: GS-10 MIDI IN,OUT Port 2: GS-10 CONTROL
fig.11-450
10.
From the File menu, select Save.
115
11.
From the Edit menu, select OMS MIDI Setup. In the OMS MIDI Setup dialog box that appears, check Run MIDI in background, and click [OK].
fig.11-460
12.
Verify that MIDI transmission and reception occur correctly.

From the Studio menu, choose [Test Studio].
fig.11-470
If a MIDI sound module is connected to the GS-10, the following step will cause a relatively loud sound to be produced by the sound module, so it is a good idea to turn down the volume on the sound module first.
13.
If a MIDI sound module is connected to the GS-10s MIDI OUT connector, click the GS-10 MIDI IN,OUT icon in the Studio Setup window.
If you hear sound, the settings have been made correctly.
fig.11-480
* GS-10 MIDI IN,OUT corresponds to the GS-10s MIDI IN,MIDI OUT. GS-10 CONTROL corresponds to the GS-10s control port.
14. 15.
After you have verified this, and exit OMS Setup. Make MIDI device settings on your sequencer software.
For details on settings, refer to the manual that came with your software.
Next, you need to install the ASIO driver (p. 120).
116
FreeMIDI settings
If other MIDI devices are connected, you must turn off the power on all devices, and then make FreeMIDI settings according to the following procedure. For more on connecting MIDI sound modules, refer to the owners manual for the MIDI sound module you are using.
1. 2. 3. 4.
For instructions on switching the GS-10s driver modes, refer to Switching the Driver Mode (p. 80). Turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to other devices.
With the power switch turned OFF, use the USB cable to connect the GS-10 to your computer. Make sure that the GS-10s OUTPUT LEVEL is set to the lowest setting, then switch ON the POWER switch. Open the FreeMIDI Applications folder, and double-click the FreeMIDI Setup icon.
fig.11-490
* The first time FreeMIDI is started up, a Welcome to FreeMIDI! dialog box will appear. Click [Continue]. If this is the second or later time, select FreeMIDI Preferences from the File menu.
fig.11-500
* When OMS is installed on this computer... appears, click [FreeMIDI].
5.
Make sure that Use OMS when available is unchecked in the FreeMIDI Preferences dialog box.
If it is checked, remove the check mark, and restart FreeMIDI.
6.
In the FreeMIDI Preferences dialog box, check GS-10 Port which is located below GS-10 Driver in MIDI Configuration, and click [OK].
fig.11-510
* If the dialog box does not show GS-10 Driver, check whether the GS-10 is connected correctly, and start up FreeMIDI Setup once again.
117
The About Quick Setup dialog box will appear.

fig.11-520
* If the dialog will not appear, select Quick Setup from the Configuration menu.
7.
Click [Continue].
* If the dialog box does not show GS-10 Driver, check whether the GS-10 is connected correctly, and start up FreeMIDI Setup once again.
8.
In the dialog box that appears, set Studio Location: to GS-10,GS-10 Port. For the Cable field located below it, choose Cable 1 and click [>>Add>>].
fig.11-521
9. 10. 11.
Repeat step 8 up to Cable 2. When settings are complete, click [Done].

A setting window will appear.
In the setting window, change the device name indicating the MIDI device connected to the GS-10 as follows.
Click the device name, and you will be able to edit it. Device 1: GS-10 MIDI IN,OUT Device 2: GS-10 CONTROL
fig.11-530
12. 13.
From the File menu, select [Save], and save your settings. Verify that MIDI transmission and reception occur correctly.
From the MIDI menu, choose Check Connections.
If a MIDI sound module is connected to the GS-10, the following step will cause a relatively loud sound to be produced by the sound module, so it is a good idea to turn down the volume on the sound module first.
118
14.
If a MIDI sound module is connected to the GS-10s MIDI OUT connector, click the GS-10 MIDI IN,OUT icon in the setting window.
If you hear sound, the settings have been made correctly.
fig.11-540
GS-10 MIDI IN,OUT corresponds to the GS-10s MIDI IN,MIDI OUT. GS-10 CONTROL corresponds to the GS-10s control port
15. 16.
After you have verified this, and exit FreeMIDI Setup. Make MIDI device settings on your sequencer software.
For details on settings, refer to the manual that came with your software.
Next, you need to install the ASIO driver (p. 120).
119
Installing the ASIO driver

You must install the MIDI driver even if you will be using only audio on the GS-10. * Be sure to install the MIDI driver before you install the ASIO driver. This section explains how to install the ASIO driver that allows the GS-10 to be used by your sequencer software or audio editing software. ASIO (Steinberg Audio Stream In/Out Interface) This is an audio interface standard promoted by the Steinberg Corporation. When the GS-10 is used with ASIO-compatible software, the synchronization precision will be improved, allowing a more sophisticated music production environment.
In Special mode, the GS-10 cannot play back audio data from the Macintoshs sound manager (such as audio CDs and alert sounds).
The ASIO driver of the GS-10 supports the following audio input/output channels. Audio input Audio output 24/16 bit 24/16 bit 1 stereo ch. (2 mono chs.) 1 stereo ch. (2 mono chs.)
Here we will explain how to install the ASIO 1.0 16 bit-compatible driver.
If your ASIO-compatible software supports ASIO 2.0 or recording/playback of 24 bit audio data, using the following drivers will provide a higher quality environment. ASIO-compatible software ASIO2.0-compatible 24 bit compatible x x x o x x o o
Driver to use GS-10 ASIO1.0 16 bit GS-10 ASIO1.0 24 bit GS-10 ASIO2.0 16 bit GS-10 ASIO2.0 24 bit
1.
From the Driver E (Mac OS 9/8) ASIO folder of the CD-ROM, copy [GS-10 ASIO1.0 16bit] to the [ASIO Drivers] folder within the ASIO Drivers folder of the ASIO-compatible software you are using (e.g., Cubase VST, Logic Audio, Digital Performer, Metro, or SPARK LE).
fig.11-550
2. 3.
Start up your ASIO-compatible software (e.g., Cubase VST, Logic Audio, Digital Performer, Metro, or SPARK LE). Open the Audio setting dialog box of your ASIO-compatible software, and select [GS-10 ASIO 16bit] as the ASIO Device.
The Audio setting dialog box will be named differently depending on your software. For details refer to the manual of your software.
120
1. 2. 3.
Mac OS X users
With the GS-10 disconnected, start up Mac OS.
Insert the CD-ROM into the CD-ROM drive. Double-click the GS10USBDriver icon (found in the Driver (Mac OS X) of the CD-ROM).
In case of Mac OS X v10.1.5, the display will indicate Authorization, then click on the key symbol.
fig.11-560
4.
The Authenticate dialog box will appear; type your password and click OK.
The display will indicate Welcome to the GS-10 USB Driver Installer.
fig.11-570
5. 6.
Click [Continue].
The display will indicate Select a Destination.
Click the drive on which the system is installed, then click [Continue].
The display will indicate Easy Install.
fig.11-590
7.
Click [Install] or [Update].

The display will indicate Installing this software requires you to restart....
fig.11-600
121
8.
Click [Continue Installation].

The display will indicate The software was successfully installed.
fig.11-610
9.
Click [Restart] to restart your Macintosh.
122
Installing the OS-standard driver

Mac OS 9/8 users......................... (p. 123) Mac OS X users ............................ (p. 126)
1. 2. 3.
Mac OS 9/8 users

With the GS-10 disconnected, start up Mac OS. Exit all currently running software (applications).
If you are using a virus checker or similar software, be sure to exit it as well.
After starting up Mac OS, select Apple System Profiler from the Apple menu.
The Apple System Profiler dialog box will appear.
fig.11-620
4. 5. 6. 7.
Click the Devices and Volumes tab. Before connecting the USB cable, switch the GS-10s driver mode to Standard.
Wait for approximately five seconds. While you are waiting, the screen display will not change, but the GS-10 is being detected. Do not touch the mouse or keyboard. This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally.
8.
In order to check that detection has been completed, once again go to Apple System Profiler, and select Update all information from the Commands menu.
In the USB area, three audio devices will be displayed. If these are displayed correctly, driver installation has succeeded.
fig.11-630
9.
In the File menu, click Quit to close Apple System Profiler.

If they are not displayed correctly, disconnect the GS-10, wait for about ten seconds, and then repeat the procedure from step 2.
123
Settings the sound input/output
1.
From the Apple menu, select Control Panel Sound.

The Sound dialog box will appear.
fig.11-640
The Sound dialog box will appear.
2.
Click the Speakers tab or Speaker Settings.

fig.11-650
3.
With the volume turned down on the GS-10 and on your peripheral audio equipment, click [Start Test].
Test signals will be output from the GS-10; left first, then right, as indicated in the screen.
fig.11-660
4.
In the Sound dialog box, click the Input tab.
124
5.
In Choose a source for sound input (Device), select USB audio.

fig.11-670
If USB audio is not displayed, close the Sound dialog box, and disconnect the GS-10s USB cable from the Macintosh. Perform the driver installation (p. 123) once again.
* Do not check Play sound through output device.
6. 7.
When you are finished making settings, close the Sound dialog box. From the File menu, select Quit.
125
1. 2.
Mac OS X users
With the GS-10 disconnected, start up Mac OS.

3. 4. 5. 6.
With the power switch turned OFF, use the USB cable to connect the GS-10 to your computer. Make sure that the GS-10s OUTPUT LEVEL is set to the lowest setting, then switch ON the POWER switch. Open System Preferences and click Sound.
fig.11-680
7.
In the Sound Effects tab, set Play alerts and sound effects through to GS10.
Now, try clicking on an alert in the list. If the sound of the alert comes from the GS-10 when you do so, it means that the GS-10 is being recognized and that the driver has been installed properly.
fig.11-690
Once set this way, all sounds from your Macintosh (including audio alerts) will be output only through the GS-10, not from the speakers of your Macintosh.
126
8.
In the Output tab, set Choose a device for sound output to GS-10.
fig.11-700
The Main Volume slider will not move.
9.
In the Input tab, set Choose a device for sound input to GS-10.
fig.11-710
Cautions when using the GS-10

Before you use your software, please note the following points. Select GS-10 in the audio driver setting of your software. For details, refer to the manual that came with your software. Connect the GS-10 to your computer via a USB cable before you start up your sequencer or other software. Do not disconnect the USB cable from the GS-10 while your sequencer or other software is running. Disconnect the USB cable from the GS-10 only after you have quit your sequencer or other software. Leave the Sleep function of your Macintosh turned off. The GS-10 will not work in the Classic environment of Mac OS X. Use the GS-10 when the Classic environment is not running.
127
Setting the Special Drivers Functions

Adjusting the audio latency
When using the GS-10 in Advanced mode, you can change the driver settings to adjust the latency of the audio. To adjust the latency, change the Buffer Size in the driver settings dialog box.
1. 2.
As described in Opening the special driver settings dialog box (p. 129), open the Driver Settings dialog box. Adjust the driver buffer size.
The following setting will produce the shortest latency.
Windows:
Set Audio Buffer Size to the far left (Min).
Macintosh:
Set Buffer Size to the far left (Min).
3. 4. 5.
Click [OK] to close the driver settings dialog box. Restart the application that is using the GS-10.
If you are using an application that has a function for testing audio devices, get it to perform its tests.
Play back audio data on your application.

If interruptions occur in the sound, repeat this procedure, and gradually increase the buffer size specified in step 2 until interruptions no longer occur. * Depending on the application you are using, there may be a buffer size or latency adjustment function among the audio settings of the application as well. For details, refer to the operation manual for your application.
Using ASIO Direct Monitor

If you are using the GS-10 from an ASIO 2.0 compatible application, switching of the GS-10s output signals (Switching the Output Signals (Direct Monitor) (p. 79)) can be controlled from your ASIO 2.0 compatible application.
1. 2. 3.
As described in Opening the special driver settings dialog box (p. 129), open the Driver Settings dialog box. Check the Use ASIO Direct Monitor check box. Click [OK] to close the driver settings dialog box.
* Depending on the application you are using, there may be a ASIO Direct Monitor among the audio settings of the application as well. For details, refer to the operation manual for your application. * When using ASIO Direct Monitor, monitoring may switch on/off at unexpected times, depending on the application settings and on the recording procedure. If this occurs, uncheck the check box in step 2 to disable ASIO Direct Monitor.
128
Setting the Special Drivers Functions
Opening the special driver settings dialog box

If using Windows: 1. Open the Control Panel and double-click BOSS GS-10.
The BOSS GS-10 Driver Settings dialog box will appear. * In Windows XP, click Switch to classic view to switch the display to the classic view. BOSS GS10 will not be displayed unless the classic view is selected. * In Windows Me, click View all Control Panel options.
If using Macintosh: 1. Open the ASIO Control Panel from the Audio Settings dialog box of your ASIO-compatible application.
The name of the Audio Settings dialog box and the procedure for opening the ASIO Control Panel will differ depending on your application. For details, refer to the operation manual for your application.
129
Troubleshooting
If there is no sound or other operational problems occur, first check through the following solutions. If this does not resolve the problem, then contact your dealer or a nearby Roland service station.
Sound from devices connected to the INPUT jack is not heard in the headphones
Is the AUX INPUT LEVEL raised to suitable level? Adjust the volume level.
Problems when using the GS-10

Problems with the sound
No sound / volume too low
Are the built-in speakers set to OFF? Press [SPEAKER ON/OFF] to ON (p. 15). Are the connection cables broken?
Is the Dir Monitor (p. 79) set to OFF?
Note that turning off this setting will stop the sounds from being output when the application is not recording or if its settings are not correctly made. Set to ON.
The volume level of the instrument connected to INPUT is too low

Could you be using a connection cable that contains a resistor?
Try using a different set of connection cables. Is the GS-10 correctly connected to the other devices?
Use a connection cable that does not contain a resistor. Is the AUX INPUT LEVEL knob lowered?
Check connections with the other devices (p. 14). Is the connected amp/mixer turned off, or the volume lowered?
Adjust the AUX INPUT LEVEL knob to an appropriate position (p. 17). Is USB:Input Level set to a low value?
Check the settings of your amp/mixer system. Is the OUTPUT LEVEL knob lowered?
Adjust the setting to an appropriate value (p. 78). Is Mic Gain set to a low value?
Adjust the OUTPUT LEVEL knob to an appropriate position (p. 15). Is Tuner set to On?
Adjust the setting to an appropriate value (p. 20).
When the volume is set to Mute in the Tuner mode, even the direct sound will not be output by setting the Tuner to On (p. 64). Is each effect set correctly?
The sound of a device connected to the AUX INPUT jack is distorted

If you are inputting sound through the AUX IN jacks, use AUX INPUT LEVEL knob of the GS-10 to lower the input level.
Use the Meter function (p. 67) to check the output level of each effect. If there is an effect for which the meter does not move, check the settings for that effect. Is USB/DIG:Out Levl set to a low value?
The sound of a device connected to the MIC INPUT jack is distorted

If you are inputting sound through the MIC INPUT jacks, adjust the Mic Gain (p. 20) of the GS-10 to lower the input level.
Adjust the setting to an appropriate value (p. 78). Is FV: Level or MST: Patch Level specified as an assign Target?
Oscillating sound occurs

Is the AUX INPUT LEVEL knob turned up too high? If inputting audio from AUX INPUT, reduce the input level with the AUX INPUT LEVEL knob. Is Mic Gain set to a high value?
Move the controller to which it is assigned. Is the Dir Monitor (p. 79) set to OFF?
Note that turning off this setting will stop the sounds from being output when the application is not recording or if its settings are not correctly made. Set to ON.
Lower the Mic Gain (p. 20) value. Is the value for any gain- or volume-related effects parameter set too high?
Lower these values.
130
Troubleshooting
Other Problems
Patch does not change
Is something other than the Play screen shown in the display?
When you send messages from the GS-10, make sure the GS-10 is set to the settings appropriate for sending data.
Check the on/off status for transmission of program change messages and the settings for the controller numbers to be transmitted (p. 70) .
On the GS-10, patches can be selected only when the Play screen is displayed. Press [EXIT] to return to the Play screen (p. 15).
The GS-10 cannot be controlled with the MIDI controller connected to the MIDI IN connector
Are you connected via USB? If the GS-10 is connected via USB with the driver mode set to Advanced, messages to MIDI IN are transmitted to the computer via USB. Disconnect the USB cable.
Parameters specified with Assign cant be controlled

Could the effect be switched off? To control a parameter using the expression pedal or CTL pedal, make sure the effect that contains the parameter you intend to control is switched on. Is something other than Assign 18 selected for the Expression Pedal function setting?
Problems common to Windows and Macintosh Problems occurring only in Windows Problems occurring only in Macintosh
When operating an expression pedal connected to the EXP PEDAL/CTL 1, 2 jack, set the Expression Pedal function (p. 58) to Assign 18. Is something other than Assign 18 selected for the CTL 1, 2 function setting?
Problems related to the USB driver
When operating a foot switch connected to the EXP PEDAL/CTL 1, 2 jack, set the CTL 1, 2 function (p. 59) to Assign 18. Do the MIDI channel settings of both devices match?
Make sure that the MIDI channels of both devices match (p. 69). Do the controller number settings of both devices match?
An Unknown driver found dialog box appears, and you are unable to install the driver
Make sure that the controller number of both devices match (p. 70).
Find new hardware wizard does not execute automatically
MIDI messages are not transmitted/ received

Are the MIDI cables broken? Try another set of MIDI cables. Is the GS-10 correctly connected to the other MIDI device?
Find new hardware wizard ends before the process is completed

It may take about 15 seconds (or more) after the USB cable is connected for the GS-10 to be detected. Is the USB cable connected correctly?
Check connections with the other MIDI device. Do the MIDI channel settings of both devices match?
Make sure that the GS-10 and your computer are correctly connected via a USB cable. Is USB enabled on your computer?
Make sure that the MIDI channels of both devices match (p. 69).
Refer to the operation manual for your computer, and make sure that USB is enabled.
131
Troubleshooting
It has been found that in some cases, not all of the Windows 98 files required to support audio via USB are installed when a computer is shipped.
Driver is not installed correctly

As described in Deleting the special driver (p. 139), delete the USB audio device driver that is installed in your computer, and then install the GS-10 driver once again as described in Installing & Setting Up the Driver (Windows) (p. 92). Also check whether there is an Unknown device in Other devices or Universal Serial Bus Controller. If you find one, delete it.
Please contact the manufacturer of your computer. Does your computer meet the USB specifications?
If you are using a computer that does not fulfill the electrical requirements of the USB specifications, operation may be unstable. In this case, you may be able to solve the problem by connecting a USB hub. Does Unknown device appear for Other device or Universal serial bus controller?
Use the following procedure to delete Other device (Universal Serial Bus Controller) Unknown device, and then restart your computer. 1. In the Windows Control Panel, double-click System. The System Properties dialog box will appear. 2. Click the Device Manager tab. 3. Double-click Other device or Universal Serial Bus Controller to display a list of devices. 4. From the list, select the unknown device and click [Delete]. 5. In the dialog box that asks you to confirm the deletion, click [OK]. 6. Verify that Other device or Unknown device is not displayed in the list, and click [Close] to close the dialog box.
Cant install/delete/use the driver in Windows XP/2000

Did you log on to Windows as a user with administrative privileges?
In order to install/delete/re-install the driver in Windows XP/2000, you must be logged into Windows as a user with administrative privileges, such as Administrator. For details, please contact the system administrator for your computer system. Did you make Driver Signing Options?
In order to install/re-install the driver, you must make Driver Signing Options. (Windows XP p. 93, Windows 2000 p. 97)
Found unknown device appears even though you installed the driver
If your computer or USB hub has two or more USB connectors, and you connect the GS-10 to a USB connector to which the GS-10 has never been connected before, the Unknown device dialog box may appear even on a computer onto which you have already installed the driver.
Windows XP/2000 displays a Hardware Installation or Digital Signature Not Found dialog box
Did you make Driver Signing Options? In order to install/re-install the driver, you must make the settings described in Driver Signing Options. (Windows XP p. 93, Windows 2000 p. 97)
Refer to Installing & Setting Up the Driver (Windows) (p. 92), and install the driver once again. This is not a malfunction.
132
Troubleshooting
Device Manager shows ?, !, or USB Composite Device
A dialog box says Cant use driver required by USB device BOSS GS-10
[Special driver mode] Are you using only audio? You must install the MIDI driver even if you are using the GS-10 only with audio. Please install the GS-10 driver for OMS or FreeMIDI. ( Installing the special driver (p. 112))
The Insert Disk dialog box does not appear

Use the following procedure to re-install the driver. 1. Turn off the power of your computer, and start up Windows with all USB cables disconnected (except for keyboard and mouse). 2. After Windows restarts, use a USB cable to connect the GS-10 to your computer. 3. Click the Windows [Start] button, and from the menu that appears, choose Settings | Control Panel. 4. Double-click the System icon. The System Properties dialog box will appear. 5. Click the Device Manager tab. 6. Check whether you can see an indication of ?Composite USB Device, ?USB Device, !USB Device, or USB composite device displayed below Sound, Video, and Game Controllers, Other Devices, or Universal Serial Bus Controller. If you find any such indication, select it and click [Delete]. 7. A dialog box will ask you to confirm deletion of the device. Verify the contents of the dialog box, and then click [OK]. In the same way, delete all indications of ?Composite USB Device, ?USB Device, USB Device, and USB composite device that you find. If you find BOSS GS-10 with a yellow ! or a red ? displayed beside it, delete this in the same way. 8. When you have finished deleting the unwanted devices, click [OK] in the System Properties dialog box. 9. Turn off the power of the GS-10, then delete the driver. ( Deleting the special driver (p. 139)) 10. Restart Windows. Then install the driver once again. ( Installing & Setting Up the Driver (Windows) (p. 92)). * If the problem still occurs after you have taken the above measures, please refer also to the Readme file for the USB driver. The Readme file is on the CD-ROM.
Problems when using the USB driver

Operating system becomes unstable
Operation becomes unstable when the computer is started up with the GS-10 already connected
Please start up your computer with the GS-10 disconnected, and then connect the GS-10. On a computer that uses a USB keyboard, starting up the computer with the GS-10 already connected may cause operation to become unstable. In this case, start up the computer with the GS-10 disconnected, and then connect the GS-10.
Cant hear sound from the computer

Is it possible that the GS-10s OUTPUT LEVEL has been placed at 0 (turned fully counterclockwise)? Have you specified the audio and MIDI data output destination for your operating system?
You must specify the GS-10 as the audio data output destination for your computer. For details on how to make this setting, refer to Settings and checking. (Windows, Driver settings (p. 107)/ Macintosh, OMS settings (p. 114), FreeMIDI settings (p. 117)) In your playback software, have you specified the audio data output destination?
For some software, such as Cakewalk Music Creator, you will need to specify the GS-10 as the output destination for audio data. For details on the procedure for making settings, refer to the owners manual for your software.
133
Troubleshooting
Are you running multiple applications?
Cant play back / record MIDI
If multiple applications are running simultaneously, an error message may appear. If this occurs, click [OK] and exit the other applications. Even if an application window is closed, it is still running if it appears in the taskbar. Be sure to exit unneeded applications displayed. Was the driver installed correctly?
Has the MIDI device you are using been set correctly?
In order for you to play back audio data via the GS-10, the driver must be installed. For installation and settings, refer to Installing & Setting Up the Driver (Windows, p. 92 / Macintosh, p. 112). Is your computer in Suspend or Sleep mode?
In order to record/play MIDI tracks using the GS-10, you must correctly install the GS-10 driver (Installing & Setting Up the Driver (Windows) (p. 92)). Also make sure that the input port and output port are set as follows in your software. INPUT port BOSS GS-10 MIDI IN OUTPUT port BOSS GS-10 MIDI OUT
If so, get your computer to resume normal operation, then exit all applications that are using the GS-10. Next, turn the GS-10s power off, then switch it on again. Did you plug in the USB cable, or unplug it while an application was running?
Has the MIDI device you are using been selected correctly?
Select [GS-10 MIDI IN/OUT] as the MIDI output device.
Exit all applications that are using the GS-10, and exit all applications that are using the GS-10, and re-connect the GS-10. Have you selected Game compatible device or Voice modem as the output for the audio track?
Are the track outputs set correctly?
If game compatible device or voice modem (the actual name will depend on the computer you are using) is selected for the audio track of your software, the audio track may not play back. Do not select these devices as the port. Has your computer been set to enter Sleep mode?
MIDI tracks to which no MIDI playback device is assigned will not be heard. If you want to play back a MIDI track, you must make sure that the MIDI device you want to use is displayed in your software as the MIDI output port. For details, refer to the owners manual for your software.
Is OMS/FreeMIDI set correctly?
If your computer enters Sleep mode, exit the software you are using, and then restart your computer. We recommend that you set your computer to not use Sleep mode.
As described in OMS settings (p. 114) or FreeMIDI settings (p. 117), check the OMS or FreeMIDI settings. Also make sure that the device for MIDI IN/OUT is correctly selected in the MIDI settings of your MIDI sequencer software.
[Standard driver mode] Are you attempting to play back an audio CD using your computers CD player?
Is the OMS setup enabled?
If you want to play an audio CD from your computers internal CD-ROM drive, refer to When playing audio CDs from the computers internal CD-ROM drive, or using the GS-10 to play game music (p. 111).
If a diamond-shaped symbol is not displayed at the left edge of the title area in the OMS setup window, the setup is not enabled. From the OMS File menu, choose Make Current. (OMS settings (p. 114))
Are the Volume Control faders raised?
Adjust the volume of the faders as described in Volume Control setting (p. 110).
134
Troubleshooting
Interrupted notes or delays occur during MIDI playback

Make Windows XP settings to enable background processing.
Noise is heard during audio playback
Is the AUX INPUT LEVEL knob raised?
Make the following settings so that MIDI processing will occur smoothly. 1. Click the Windows start button, and from the menu that appears, select Control Panel. 2. In Pick a category, click Performance and Maintenance. 3. In or pick a Control Panel icon, click the System icon. 4. Click the Advanced tab. 5. At the right of the Performance field, click [Settings]. The Performance Options dialog box will appear. 6. Click the Advanced tab.
fig.12-010
If you are not using any audio devices connected to the AUX INPUT, set the AUX INPUT LEVEL knob to minimum position. Is a mic or guitar still connected?
If a mic or guitar is connected to the GS-10, disconnect the mic or guitar. Disconnect any audio devices you are not using. Noise is sometimes heard in the line input or mic input.
If a USB-compatible MIDI sound module and the GS-10 are connected via USB to the same computer, and the outputs of the MIDI sound module are connected to the line input jacks of the GS-10, noise from your computer may be heard via the MIDI sound module from the GS10, depending on the computer you are using. If this occurs, you can either connect the MIDI sound module and the GS-10 in parallel using a self-powered hub, or connect the MIDI sound module via its serial or MIDI interface. Are two or more audio devices such as the GS-10 or a mixer connected to your computer?
7. In the Processor Scheduling field, select Background services, and click [OK]. 8. In the System Properties dialog box, click [OK]. The System Properties dialog box will close.
Try connecting only a single GS-10 unit, and check whether the noise disappears. If numerous audio devices are connected to a computer, noise may occur depending on your system. In such cases, connect only the GS-10 to your computer.
Does your sequencer software support ASIO 2.0?
If your ASIO-compatible software does not support ASIO 2.0, it will not operate correctly if you use [GS-10 ASIO2.0 16bit] or [GS-10 ASIO2.0 24bit] as the ASIO driver. In this case, select either [GS-10 ASIO1.0 16bit] or [GS-10 ASIO1.0 24bit] as the ASIO driver.
Does your sequencer software support 24-bit audio?
If your ASIO-compatible software does not support 24bit audio input/output, it will not operate correctly if you select [GS-10 ASIO1.0 24bit] or [GS-10 ASIO2.0 24bit] as the ASIO driver. In this case, select either [GS-10 ASIO1.0 16bit] or [GS-10 ASIO2.0 16bit] as the ASIO driver.
135
Troubleshooting
4. In the Display Properties dialog box, click [OK] to close the dialog box. Is the GS-10 connected to a USB hub? Try connecting the GS-10 directly to the USB connector of the Macintosh itself. 5. Restart your computer.
Are you using a USB device other than the GS-10?
In Windows XP, make the settings that enable background processing.
Try turning off the power of all USB audio devices other than the GS-10.
Make these settings so that audio processing can be performed smoothly. Make settings as described in Make Windows XP settings to enable background processing (p. 135).
In some cases, you may also be able to solve this problem by grounding the chassis of your computer, or the grounding connector of the AC power supply plug of your computer. In addition, you can check whether any devices that produce a strong magnetic field are located nearby, such as a television or microwave oven. Also check the troubleshooting item Sound is interrupted during audio recording/playback.
Try using the following procedure to change your disk drive settings. The following setting item may not exist on some computers. 1. In the Windows Control Panel, double-click System. 2. Click the Device Manager tab. 3. Double-click Disk Drives to see the list of devices. 4. From the list, select GENERIC IDE DISK TYPE??, and click Properties to access the GENERIC IDE DISK TYPE?? Properties dialog box. * In the ?? field of GENERIC IDE DISK TYPE??, there will be a number that differs depending on your computing environment. 5. Click the Settings tab, place a check mark in the check box for the DMA option, and click [OK] to close the dialog box. * Depending on your system, a DMA Settings dialog box may appear. Check the contents, and click either [OK] or [Cancel].
Sound is interrupted during audio recording/playback
Are many applications running on your computer?
If you use many applications or start up other applications during playback, playback may be interrupted, depending on your computer system. Please exit unneeded applications, and try again. If this does not resolve the problem, try restarting your computer.
Graphic accelerators may cause noise to be heard during audio playback.
6. In the System Properties dialog box, click [OK] to close the dialog box. 7. Restart your computer.
Use the following procedure to turn the graphic accelerator Off. 1. In the Windows Control Panel, double-click Display to open the Display Properties dialog box, and click the Settings tab. 2. Click Advanced, and in the properties that appear, click the Performance tab. For Windows XP, click Advanced, and then click the Troubleshoot tab. For Windows 2000, click Advanced, and then click the Troubleshooting tab. 3. Set the Hardware acceleration slider to None, and click [OK].
Try installing more memory.
Installing more memory will increase the performance of your computer. For details on how to install more memory, refer to the operation manual for your computer.
136
Troubleshooting
Does your computer satisfy the requirements of the USB standard?
Depending on the virtual memory setting or networkrelated settings, noise may occur.
If you are using a computer (such as a computer that you yourself assembled) that does not satisfy the electrical requirements of the USB specifications, you may experience interruptions in the audio. If this occurs, you may be able to solve the problem by connecting a USB hub that contains its own power supply. On some computers, audio playback may be interrupted due to the Power Management settings in the Control Panel.
Please make the following settings before use. In Chooser of the Apple menu, set AppleTalk to Inactive. (This setting is not changed as a result of turning off AppleTalk, as requested by OMS when sequencer software is started up. You must change the setting yourself using the Chooser.) In the Memory Control Panel, set Virtual Memory to Off. Depending on the way in which you connect to the Internet, use the GS-10 with the following settings. If you connect to the Internet via a LAN cable Use while the LAN cable is connected. If you connect to the Internet via the internal modem port, or are not connected to the Internet In the TCP/IP Control Panel, set Connect via to PPP. After you have made the settings, restart your Macintosh. * Do not use software that accesses the network (such as a Web browser) at the same time that you are using sequencer software or audio editing software.
The Power Supply Properties that you see when you double-click Power Management will differ depending on your computer system. One example is given below, but you should also refer to the operation manual for your computer. Some computers may not have all of the following setting items. 1. Click the Windows Start button, and select Settings | Control Panel to open the Control Panel. 2. In Control Panel, double-click System to open the System Properties dialog box. 3. Click the Device Manager tab. 4. Double-click System Devices to display the list of devices. 5. From the list, select Advanced Power Management Support. Then click Properties to open the Advanced Power Management Support Properties dialog box. 6. Click the Settings tab, and in Troubleshooting, place a check in the check box for Dont Poll Power Supply Status. Then click [OK]. 7. In the System Properties dialog box, click [OK]. 8. Restart Windows.
Try increasing the Buffer Size in the ASIO Driver control panel. The name of the settings dialog box will differ depending on your software. * If you change the buffer size, you must exit the software and then restart it. * BOSS/Roland can make no guarantee of, nor provide support regarding the operation of sequencer software and audio editing software made by another manufacturer. Please contact the manufacturer of the software you are using.
If you are using the special driver, you can solve this problem in the BOSS GS-10 Driver Settings dialog box.
For details, refer to the section Something is wrong with playback; sound is interrupted or notes are missing within the Readme_e file located in the folder in which you installed the CD-ROM.
137
Troubleshooting
Digitally recorded sound is distorted, is at the wrong pitch, or contains noise

Is the application's sampling frequency set to 44.1 kHz?
Game background music does not play

Does the game use an audio CD for background music? (Standard driver mode)
Set the application's sampling frequency to 44.1 kHz.
Playback or recording halts midway through, and then becomes impossible

Was a heavy processing load experienced while using the GS-10, such as accessing the CD-ROM drive or a network?
If the game uses an audio CD for background music, refer to When playing audio CDs from the computers internal CD-ROM drive, or using the GS-10 to play game music (p. 111).
Sound becomes distorted or noisy when you apply an effect

Adjust the volume of the effects.
If an operation involving a heavy processing load is performed while the GS-10 is in use, it may not operate correctly. If this occurs, stop playback/recording, and then try resuming playback/recording. If you are still unable to play back/record, exit all applications that use the GS-10, switch off the GS-10, then turn it on again.
A loud buzz is present in the guitar signal

Does the buzz decrease when you lower the volume of your guitar?
Recording produces a silent (blank) file

Try setting the bit rate to 16 bit or higher. If you are using Windows 98 Second Edition and your recording software is set to a bit rate setting of 8 bits, a silent file may be created, effectively making recording impossible. If this occurs, set the bit rate to 16 bit or higher, and you will be able to record normally. Is the Recording source select switch set correctly? In your operating system, is the audio data input destination set correctly? On your recording software, is the audio data input destination set correctly?
If the buzz decreases when you lower the volume of your guitar, it is possible that the pickup of your guitar is receiving noise from a computer or a display screen. Move as far away from the computer as possible. Sometimes this problem can be solved by grounding the chassis of your computer, or the grounding connector of your computers AC power supply. You should also check whether there is a device nearby that produces a strong magnetic field, such as a television or a microwave oven. (p. 4)
138
Troubleshooting
Deleting the special driver

If you were unable to install the special driver according to the procedure given, the GS-10 may not be recognized correctly by the computer. In this case, use the following procedure to delete the special driver, and then follow the procedure in Installing & Setting Up the Driver (Windows, p. 92; Macintosh, p. 112) to install the driver once again.
Macintosh users
1. Disconnect the USB cable (by which the GS-10 is connected) from your Macintosh. 2. From the system extensions folder, drag USB GS-10 Driver into the trash to delete it. 3. Delete GS-10 from the OMS Folder inside the System folder, or drag GS-10 Driver from the FreeMIDI Folder to the trash. 4. Drag the ASIO driver that you installed in Installing the ASIO driver (p. 120) into the trash to delete it. 5. Restart the Macintosh.

In order to delete (uninstall) the driver, a user with administrative privileges such as Administrator must be logged onto Windows. For details, contact the system administrator of your computer. 1. Start Windows with all USB cables disconnected. (except the keyboard and mouse) 2. Log on to Windows as one of the following users: a user whose account type is Computer Administrator the Administrator or other user with the privileges of the Administrators group * For more information regarding this, consult your computer system administrator. 3. Double-click Uninstal.exe. 4. The display will indicate This program uninstalls the BOSS GS-10 USB Driver installed, and click the OK button. 5. The display will indicate Uninstallation completed, and click the Yes button. Windows will restart.
Windows Me/98 users

1. Start Windows with all USB cables disconnected. (except the keyboard and mouse) 2. Exit all applications before performing the uninstallation. 3. Double-click Uninstal.exe. 4. The display will indicate This program uninstalls the BOSS GS-10 USB Driver installed, and click the OK button. 5. The display will indicate Uninstallation completed, and click the Yes button. Windows will restart.
139
Index
Numerics
2x2 Chorus ........................................................................ 45 Display ............................................................................. 10 DRIVE ......................................................................... 10, 21
A
AC Adaptor ...................................................................... 12 AC IN ............................................................................... 12 Advanced ......................................................................... 70 Advanced Compressor ..................................................... 38 ASSIGN ................................................................. 11, 6061 Assign .......................................................................... 60, 66 Active Range ............................................................... 63 Source ......................................................................... 63 Source Mode ............................................................... 63 Target .......................................................................... 61 Target Range ............................................................... 62 Assign 1-8 .................................................................... 5859 Assign Hold ...................................................................... 66 Auto Riff ........................................................................... 49 Auto Wah ......................................................................... 36 AUX .................................................................................. 20 AUX INPUT ................................................................ 12, 17 AUX INPUT LEVEL ......................................................... 11
E
Effect Chain ................................................................ 24, 54 Effect On/Off ................................................................... 22 Enhancer ........................................................................... 39 EQ ..................................................................................... 11 Equalizer ........................................................................... 35 EXIT .................................................................................. 11 EXP PEDAL/CTL 1,2 ....................................................... 12 Expression Pedal .............................................................. 58
F
Factory Reset .................................................................... 86 FEEDBACK ................................................................ 10, 21 Feedbacker ........................................................................ 40 Flanger .............................................................................. 42 Foot Switch ....................................................................... 59 Foot Volume ............................................................... 54, 58 FX-1 ............................................................................ 11, 36 FX-2 ............................................................................ 11, 41
B
BASS ............................................................................ 10, 21 Bass ................................................................................... 19 Bass Simulator .................................................................. 52 Bulk Dump ....................................................................... 71 Bulk Load .................................................................... 7172 Bypass .............................................................................. 65
G
GAIN .......................................................................... 10, 21 GS-10s Speakers ............................................................... 15 Guitar ............................................................................... 19 GUITAR AMP OUT .................................................... 12, 16 Guitar Synth ..................................................................... 50 GUITAR/BASS ................................................................. 11
C
CAPS ................................................................................ 24 CHANNEL SELECT .................................................... 10, 27 Channel Select .................................................................. 28 Copy ........................................................................... 27 CHORUS ..................................................................... 11, 21 Chorus .............................................................................. 34 Combo AMP ..................................................................... 16 Combo Return .................................................................. 16 COMP .......................................................................... 10, 21 Compressor ...................................................................... 31 Control 1, 2 ....................................................................... 59 COSM ................................................................................. 9 Customize COSM Amp ................................................................ 55 Overdrive/Distortion ................................................. 56 Pedal Wah ................................................................... 57 Speaker ....................................................................... 56
H
Harmonist ......................................................................... 43 Humanizer ........................................................................ 48
I
INPUT SELECT .......................................................... 11, 19 INS .................................................................................... 24
J
JUMP ................................................................................ 23
K
Knob Mode ....................................................................... 66
L
LCD Contrast .................................................................... 65 LEVEL ................................................................... 1011, 21 Level Meter ....................................................................... 67 Limiter .............................................................................. 38 Line/Phones ..................................................................... 16
D
Defretter ........................................................................... 40 DEL .................................................................................. 24 DELAY ........................................................................ 10, 21 Delay ................................................................................ 33 DIGITAL OUT ............................................................. 12, 17 DIRECT PATCH .................................................... 11, 18, 27
M
Master BPM ...................................................................... 54 METER ....................................................................... 11, 67 MIC GAIN ........................................................................ 20
140
Index
MIC INPUT ...................................................................... 12 Microphone ...................................................................... 19 MIDDLE ...................................................................... 10, 21 MIDI ............................................................................ 68, 82 Control 1 Out .............................................................. 70 Control 2 Out .............................................................. 70 Device ID .................................................................... 69 Expression Pedal Out .................................................. 70 Knob Control Out ....................................................... 70 Omni Mode ................................................................. 69 Program Change Out .................................................. 70 Receive Channel ......................................................... 69 Remote Control ........................................................... 70 Sync Clock .................................................................. 69 Transmit Channel ....................................................... 69 MIDI IN ............................................................................ 12 MIDI OUT ........................................................................ 12 MMC ................................................................................ 70 Mute ................................................................................. 64
PRESENCE ................................................................. 10, 21 Preset Patch ...................................................................... 18 Program Change Map ...................................................... 73
Q
QUICK FX ............................................................. 11, 22, 60
R
Reference Pitch ................................................................. 64 Remote Control ................................................................ 75 REVERB ...................................................................... 11, 21 Reverb .............................................................................. 34 Ring Modulator ................................................................ 40 Rotary ............................................................................... 47
S
Short Delay ....................................................................... 48 Slicer ................................................................................. 49 Slow Gear ......................................................................... 39 SPEAKER ON/OFF .................................................... 11, 15 Stack AMP ........................................................................ 16 Stack Return ..................................................................... 16 Standard ........................................................................... 70 Stereo Equalizer ................................................................ 52 SUSTAIN .................................................................... 10, 21 SYSTEM ............................................................................ 11
N
NAME/NS/MASTER ........................................... 11, 24, 53 Noise Suppressor .............................................................. 53
O
Octave .............................................................................. 45 OD/DS ........................................................................ 10, 21 OUTPUT ........................................................................... 12 OUTPUT LEVEL ......................................................... 11, 15 Output Level .................................................................... 15 OUTPUT SELECT ............................................................ 16 Overdrive/Distortion ....................................................... 32
T
TAP ................................................................................... 11 Tone Modify ..................................................................... 37 TREBLE ...................................................................... 10, 21 Tremolo ............................................................................ 39 TUNER ............................................................................. 11 Tuner ................................................................................ 64
P
Pan .................................................................................... 46 PARAMETER ................................................................... 11 Patch ................................................................................. 18 Copy ........................................................................... 25 Exchange ..................................................................... 26 Initialize ...................................................................... 26 Register ....................................................................... 27 Write ........................................................................... 25 Patch Change .................................................................... 18 Patch Extent ...................................................................... 65 Patch Level ....................................................................... 54 Patch Name ................................................................. 24, 53 PATCH/VALUE .............................................................. 11 Pedal Bend ................................................................... 45, 58 Pedal Wah ................................................................... 36, 58 Phaser ............................................................................... 42 PHONES ........................................................................... 11 Pitch Shifter ...................................................................... 44 Play Screen ....................................................................... 15 POWER ............................................................................ 12 PREAMP .......................................................................... 21 PREAMP/SPEAKER ........................................................ 10 Preamp/Speaker Simulator .............................................. 28
U
Uni-V ................................................................................ 47 USB .................................................................. 1112, 78, 83 Direct Monitor ............................................................ 79 Direct Monitor Command ........................................... 79 Driver Mode ............................................................... 80 Input Level .................................................................. 78 Output Level ............................................................... 78 Output Mode .............................................................. 79 USB (Bass) ................................................................... 20, 81 USB (Gtr/Mic) ............................................................ 19, 81 USB Driver ........................................................................ 91 User Patch ......................................................................... 18
V
Vibrato .............................................................................. 46
W
WRITE ................................................................... 11, 2527
141
For the U.K. IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE. BLUE: NEUTRAL BROWN: LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.
For the USA
DECLARATION OF CONFORMITY Compliance Information Statement

Model Name : Type of Equipment : Responsible Party : Address : Telephone :
GS-10 Guitar Effects System with USB Audio Interface Roland Corporation U.S. 5100 S.Eastern Avenue, Los Angeles, CA 90040-2938 (323) 890-3700
142
For EU Countries
CAUTION
Apparatus containing Lithium batteries
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturers instructions.
ADVARSEL!
Lithiumbatteri - Eksplosionsfare ved fejlagtig hndtering. Udskiftning m kun ske med batteri af samme fabrikat og type. Levr det brugte batteri tilbage til leverandren.
VARNING
Explosionsfara vid felaktigt batteribyte. Anvnd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera anvnt batteri enligt fabrikantens instruktion.
ADVARSEL
Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruks joner.
VAROITUS
Paristo voi rjht, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hvit kytetty paristo valmistajan ohjeiden mukaisesti.
For EU Countries This product complies with the requirements of European Directive 89/336/EEC.
For the USA
FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE

Unauthorized changes or modification to this system can void the users authority to operate this equipment. This equipment requires shielded interface cables in order to meet FCC class B Limit.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada.
03342912
04-2-3N

Boss GS-10 Manual

Uploaded by

Copyright:

Available Formats

Boss GS-10 Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Boss GS-10 Manual

Uploaded by

Copyright:

Available Formats

Owners Manual

Printing Conventions in This Manual

USING THE UNIT SAFELY

Repairs and Data

Never strike or apply strong pressure to the display.

Unauthorized duplication, reproduction, hiring, and lending prohibited.

* Microsoft and Windows are registered trademarks of Microsoft Corporation.

* Windows is known officially as: Microsoft Windows operating system.

* Apple and Macintosh are registered trademark of Apple Computer, Inc.

* MacOS is a trademark of Apple Computer, Inc.

* OMS is a registered trademark of Opcode Systems, Inc.

* FreeMIDI is a trademark of Mark of the Unicorn, Inc.

Panel Descriptions ..........................10

Chapter 1 Playing Sounds ..............................14

Chapter 4 Introduction to Effects and Parameters .... 28

Chapter 2 Creating Your Own Favorite Tones (Patches) ........................................18

Chapter 7 Convenient Functions and System Settings ... 64

Chapter 5 Creating Original Effects Types (Customize) ..55

Chapter 6 Setting the External Pedal Functions .....58

Chapter 9 Using the GS-10 Connected to a Computer Via USB .......78

Installing & Setup the USB Driver ...................... 91

Troubleshooting ........................... 130

Index ........................................... 140

Internal Effects Derived from the GT-6/GT-6B, Made More Powerful

The Functions You Want for Digital Recording

Accepts Multiple Inputs

Stereo Monitor Speakers Built-In

GS-10 Editor and GS-10 Librarian Included

WDM/ASIO-Compatible USB Driver

COSM (Composite Object Sound Modeling)

3. COMP (Compressor) (p. 21, p. 31)

2. PREAMP/SPEAKER (p. 21, p. 28) (Preamp/Speaker Simulator)

COMP On/Off Button

4. OD/DS (p. 21, p. 32) (Overdrive/Distortion)

OD/DS On/Off Button

5. DELAY (p. 21, p. 33)

PREAMP/SPEAKER On/Off Button

DELAY On/Off Button

CHANNEL SELECT Button

17. EXIT Button

18. WRITE Button

6. CHORUS (p. 21, p. 34)

19. AUX INPUT LEVEL Knob

CHORUS On/Off Button

7. REVERB (p. 21, p. 34)

20. OUTPUT LEVEL Knob

REVERB On/Off Button

21. USB Button (p. 78)

8. FX-1 (p. 36)

22. SPEAKER ON/OFF Button (p. 15)

9. FX-2 (p. 41)

23. METER Button (p. 67)

24. SYSTEM Button

10. EQ (Equalizer) (p. 35)

25. TUNER Button (p. 64)

11. NAME/NS/MASTER Button (p. 24, p. 53)

26. DIRECT PATCH Button (p. 18)

12. ASSIGN Button (p. 60)

27. PHONES Jack

28. GUITAR/BASS Jack