FSAE Design Spec Sheet: Car No. School
FSAE Design Spec Sheet: Car No. School
FSAE Design Spec Sheet: Car No. School
-- Note: SI units
Competitors please replace the sample specification values in the table below with those appropriate for your vehicle and submit this to with your design report. This information will be reviewed by the design judges and event. --Please do not modify format of this sheet. Common formatting will help keep the judges happy! --The sample values are fictional and should not be used as the baseline for your designs.
Ergonomics Driver Size Adjustments Seat (materials, padding) Driver Visibility (angle of side view, mirrors?) Shift Actuator (type, location) Clutch Actuator (type, location) Instrumentation Frame Frame Construction Material Joining method and material Targets (Torsional Stiffness or other) University of Wisconsin-Platteville_95_spec.xls V1 1
Fixed seat and steering wheel with adjustable pedal tray and headrest Fiberglass CSM and Kevlar cloth construction w/ foam inserts 220 degrees side visibility Cable actuated via handle on left side of cockpit cable actuated in conjuction with shifter via handle Digital readout in dash with warning lights
Complete Tubular space frame 4130 chro-moly alloy steel tubing 1.0" Dia .049" to .095" wall thickness TIG welded using ER70-S filler 1800 lb-ft/deg torsional rigidity, 65 lb bare frame weight (with brackets and paint) 4/14/12
Torsional stiffness and validation method Bare frame weight with brackets and paint Crush zone material Crush zone length Crush zone energy capacity Powertrain Manufacture / Model Bore / Stroke / Cylinders / Displacement Compression ratio Induction Throttle Body / Mechanism Fuel Type Max Power design RPM Max Torque design RPM Min RPM for 80% max torque Fuel System (manf'r, and type) Fuel System Sensors (used in fuel mapping) Fuel Pressure Injector location Intake Plenum volume and runner length(s) Exhaust header design Effective Exhaust runner length Ignition System Ignition Timing Oiling System (wet/dry sump, mods) Coolant System and Radiator location Fuel Tank Location, Type Muffler Other significant engine modifications Drivetrain Drive Type Differential Type Final Drive Ratio Vehicle Speed @ max power (design) rpm 1st gear 2nd gear 3rd gear 4th gear 5th gear 6th gear Half shaft size and material Joint type Aerodynamics (if applicable) Front Wing (lift/drag coef., material, weight) Rear Wing (lift/drag coef., material, weight) Undertray (downforce/speed) Wing mounting Optional Information Body Special Bit A Special Bit B
1829 lb-ft/deg verified in Algor 67 lbs LAST-A-FOAM FR-6706, a closed-cell polyurethane foam 434 mm Dynamic Test-7980 Joules
Yamaha YZF-R6P 65.5mm bore / 44mm stroke / 4 cylinder / 599 cc 13.5:1 Naturally Aspirated Custom 32mm Butterfly Throttlebody E-85 10500 9000 7500 Student built Megasquirt Fuel injection system, batch injection Throttle Position, Oxygen, Crank position, MAP, IAT 3 bar 167 mm before and pointing toward back of intake valve 2260 cc, 18.41cm runners (4) 35mm ID runners into (1) 50mm collector equal length 500 mm (+/-7mm) Student des/built, wasted spark system 3-D map, RPM based, 22 deg BTDC max advance Wet sump, special cast aluminum pan (shortened depth), custom oil baffling plates Single Side pod mounted Radiator, with High Performance electric fan Side Mounted between firewall and engine, stainless steel tank Stock Sportbike style muffler , 4200cc volume High Compression Pistons, Camshaft reground with longer duration and less overla
520 o-ring Chain Cam and Pawl 4:1 84 mph 33 mph 49 mph 61 mph 71 mph 79 mph 88 mph 1.5 in. O.D x 1.26 in. I.D. hollow steel shafts Prototype CV Joint
University of Wisconsin-Platteville_95_spec.xls V1
4/14/12
2010
95 University of Wisconsin - Platteville
Rear 2705mm long, 1321mm wide, 1156mm high 1600mm 1168 mm 137 kg Rear Double unequal length A-Arm. Push rod actuated coilover spring and damper 20.0x7.0-13 R075 Goodyear 7 inch wide, 3 pc Al Rim, 25.4mm pos. offset 304 mm above ground 32mm jounce/ 32 mm rebound 48 N/mm 0.614 degrees per g 4.61 Hz 65 % of critical damping at X mm/sec 85 % of critical damping at X mm/sec 1.0 / linear 187 deg / m 4 deg /deg 0.75 deg toe out -1 deg, adj. via shims on upright mount
those appropriate for your vehicle and submit this to with your design report. This information will be reviewed by the design judges and may be referred to during the des ign
0% 76mm above ground Front steer, 25mm c-factor, 62mm steer arm Rear Outboard, fixed, hub mounted, 10" dia x .25" wide, cross drilled, 1020 steel APRacing 3/4" bore front and rear with driver adjustable bias bar 1.75" dia., dual piston, fixed mtg Opposing tapered single row roller bearings CNC 6061-Al, integral caliper mount Rotating axle, 19mm OD solid 4140 steel annealed and Ion Nitride treated
Fixed seat and steering wheel with adjustable pedal tray and headrest Fiberglass CSM and Kevlar cloth construction w/ foam inserts 220 degrees side visibility Cable actuated via handle on left side of cockpit cable actuated in conjuction with shifter via handle Digital readout in dash with warning lights
Complete Tubular space frame 4130 chro-moly alloy steel tubing 1.0" Dia .049" to .095" wall thickness TIG welded using ER70-S filler 1800 lb-ft/deg torsional rigidity, 65 lb bare frame weight (with brackets and paint) University of Wisconsin-Platteville_95_spec.xls V1 3 4/14/12
1829 lb-ft/deg verified in Algor 67 lbs LAST-A-FOAM FR-6706, a closed-cell polyurethane foam 434 mm Dynamic Test-7980 Joules
Yamaha YZF-R6P 65.5mm bore / 44mm stroke / 4 cylinder / 599 cc 13.5:1 Naturally Aspirated Custom 32mm Butterfly Throttlebody E-85 10500 9000 7500 Student built Megasquirt Fuel injection system, batch injection Throttle Position, Oxygen, Crank position, MAP, IAT 3 bar 167 mm before and pointing toward back of intake valve 2260 cc, 18.41cm runners (4) 35mm ID runners into (1) 50mm collector equal length 500 mm (+/-7mm) Student des/built, wasted spark system 3-D map, RPM based, 22 deg BTDC max advance Wet sump, special cast aluminum pan (shortened depth), custom oil baffling plates Single Side pod mounted Radiator, with High Performance electric fan Side Mounted between firewall and engine, stainless steel tank Stock Sportbike style muffler , 4200cc volume High Compression Pistons, Camshaft reground with longer duration and less overlap for E85
520 o-ring Chain Cam and Pawl 4:1 84 mph 33 mph 49 mph 61 mph 71 mph 79 mph 88 mph 1.5 in. O.D x 1.26 in. I.D. hollow steel shafts Prototype CV Joint
University of Wisconsin-Platteville_95_spec.xls V1
4/14/12