HVAC Ventilation

Page 1 of 4
1-31-07
Bill Greco
Vapor Dilution with respect to Outside Air over a period of Time
The following concerns Pharmaceutical production areas, research areas and other areas where
annoying or dangerous vapors can be released. Many times vapors are not controlled by special ventilation
apparatus such as hoods or carbon filtration. Vapors can be caused by laboratory accidents, use of cleaning
solvents applied outside of the influence of the exhaust system or by special adhoc procedures conjured up
by jury rigged processes. The primary general HVAC system often becomes the last line of defense to confine and
dilute these vapors which have escaped into a conditioned space. A primary general HVAC system is
meant to serve as supply and exhaust of air to control comfort or specifically produce a controlled environment
within regulated room classification requirements. If vapors are re-circulated and confined within a
primary general HVAC system, only outside air will dilute the unwanted vapor. Unfortunately opening
a window in most cases is not a possibility.
A prime function of many substances especially solvents is to evaporate into the local atmosphere
leaving behind a physically or chemically transformed material formerly associated with it. Evaporation
of many substances cause fumes, gases, vapors and / or mists. It is nearly always possible to
estimate the rate or use of total liquid composition, to determine the rate of evaporation.
This makes it especially simple, to handle vapor ventilation problems on a quantitative basis with relation to time.
The following could be used to calculate any concentration of vapor or could be representative of the
differential of a mixture of some substance being added over a time period in a tank of fluid through which
fresh fluid is being added and continuously removed. The procedure can be applied to any case where air is
initially charged with contaminant and it is desired to estimate the conditions in the space in relation to time.
Figure-1 shows a diagram of a primary general HVAC system that is conditioning

re-circulating air, exhausting air and introducing outside air.
Estimating the rate of generation of vapors :

A weight of any liquid equal to it’s molecular weight produces on evaporation, the same
volume of vapor as all other liquids. If the weight is given in pounds, the volume of vapor formed
by one pound molecular weight is 359 cuft at 320 F., at room temperature of 700 F:
Assume evaporation of one pound of turpentine C10 H16 which has a molecular weight of 136.23
that has evaporated over a period of one hour. The total volume of vapor per hour is :
2.839 cuft/ hour or 0.047 cuft/min or a generation rate (G) of 0.047 cfm
Page 2 of 4
1-31-07
Bill Greco
An increase in the quantity of vapor in the space during the time interval dt, is equal to the
rate of vapor being added to the space minus the removal rate of vapor leaving the space.
The relation between the ratio of concentration of vapor c and time t can be developed
from the equation:
where:
Q = Ventilation Rate, cfm (air exhausted)
G = Vapor generation rate, cfm
c = Ratio of substance vapor to air in parts per million expressed as a fraction at time t
c_initial = Initial ratio of substance vapor parts per million at time t=0
P = Cubic Displacement of the space
c t
x dc/G – Qc = 1/P xdt equation-2

co 0
which becomes:
and for cases where the initial concentration is set at zero :
solving for t =
and:
Simplifying:
Changing signs:
Page 3 of 4
1-31-07
Bill Greco
:
Multiply by P =
Divide by 0.435Q =
Rearranging =
A note concerning logs when addressing this problem:

The terms log and log10 are what is known as common logs or Briggs* logarithms,
logs to the base 10.
The terms loge and ln are known as napierian or natural logarithms, logs to the base
e or the infinite series 2.71828.....
This is mentioned to avoid confusion when solving for (t) using the equations in this report.
*= Briggs or Briggsian logs are a less used name for common logs, named for the
English mathematician and Oxford professor Henry Briggs (1561-1630), who
proposed that logarithms to base 10 would be more useful than Naperian logarithms.
Other equation forms that solve for (t) are:

Page 4 of 4
1-31-07
Bill Greco
Example-1:
Assume a research lab 30 feets long x 15 feet wide with a 10 foot high ceiling.
A repetitive procedure is being performed in which a lab technician is using 1 pound of acetone on
a lab bench for 30 minutes during each process, the procedure must be conducted outside of the
labs hood area. The primary general HVAC system as shown in Figure-1 supplies conditioned air
to the space, 170 cfm is being exhausted from the room. The room temperature is controlled
to 700 F. The procedure is started with 0 parts per million (ppm) in the room.
How long will the procedure be allowed to continue prior to reaching acetone’s threshold level
of 1,000 parts per million ?
acetone (CH3 COCH3 ) has a molecular weight of 58.08:
6.658 divided by 30 minutes = 0.188 cfm

G= 0.188 cfm
P= (30)(15)(10) = 4,500 cuft
c= 1,000 / 1,000,000 or 0.001
Q= 170 cfm
If the process is stopped at 1,000 ppm, how long will it take the room air in example-1 to
dilute and reach 500 ppm ?
c_final = 500/1,000,000 = 0.0005
Refernce:
Hemeon, W.C.L. Plant and Process Ventilation Second Edition pp 228-232

HVAC Ventilation

Uploaded by

Copyright:

Available Formats

HVAC Ventilation

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HVAC Ventilation

Uploaded by

Copyright:

Available Formats

Page 1 of 4

Vapor Dilution with respect to Outside Air over a period of Time

Figure-1 shows a diagram of a primary general HVAC system that is conditioning

Estimating the rate of generation of vapors :

x dc/G – Qc = 1/P xdt equation-2

and for cases where the initial concentration is set at zero :

A note concerning logs when addressing this problem:

Other equation forms that solve for (t) are:

Vapor Dilution with respect to Outside Air over a period of Time

acetone (CH3 COCH3 ) has a molecular weight of 58.08:

6.658 divided by 30 minutes = 0.188 cfm

c_final = 500/1,000,000 = 0.0005

You might also like