Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Wa-4 Alivio Ul-Fm 1116fm

Download as pdf or txt
Download as pdf or txt
You are on page 1of 4

Technical Bulletin

Model 1116FM (Angle) Fire Pump Pressure Relief Valve


Function
Automatically maintains a constant pressure in the fire protection system by relieving excess pressure.

Features
The WATTS ACV 1116FM (angle) relief valve meets all requirements for UL listed, FM Approved fire protection service. The design and features incorporated in the WATTS ACV valve assure accurate control, dependable performance and long life. Model 116FM: Globe Pattern Single Chamber Relief Valve Model 1116FM: Angle Pattern Single Chamber Relief Valve

Specifications
4 2

3 1 6

Body and Cover: Ductile Iron - ASTM A536 Fusion Bonded Epoxy Coated Seat (trim): Stainless Steel CF8M- Xylan Coated Internals: Stainless Steel AISI 303 or Ductile Iron - ASTM A536 Fusion Bonded Epoxy Coated Stem: Stainless Steel AISI 303 - Xylan Coated Spring: Stainless Steel AISI 302 Elastomers: BUNA- N Control Tubing: Copper Fittings: Brass Pressure Relief Control Body: Bronze SIZES / APPROVALS: 20 - 175 PSI Relief Service 100 - 300 PSI Relief Service Valve Sizes Available in Angle and Globe

CLOSES VALVE OPENS VALVE

FLOW
COMPONENTS
1 - Main Valve (Angle Pattern) 2 - PV20C Relief Control 3 - Fixed Orifice 4 - Pressure Gauge 5 - Check Valve 6 - Flow Clean Strainer

3
UL

4
UL / FM

6
UL / FM

* 8
UL / FM

1116FM

UL

Listed

* 20 - 175 Relief Service Only

Operation
The WATTS ACV Model 1116FM PRESSURE RELIEF VALVE is controlled by a Pressure Relief Control. The Pressure Relief Control is normally closed, held closed by an adjustable spring setting to maintain a constant inlet pressure to the main valve. When upstream pressure increases above the relief set-point, the Relief Control throttles open, increasing flow through the control tubing. Pressure is decreased in the main valve cover chamber, causing the main valve to modulate towards open, relieving excess upstream pressure. The desired system pressure is maintained. As the upstream pressure decreases below the relief set-point, the Relief Control throttles closed, restricting flow through the control tubing. Pressure is increased in the main valve cover chamber, causing the main valve to modulate towards closed, maintaining the desired upstream pressure. Should upstream pressure drop below and remain below the set-point, the main valve closes drip tight.
8550 Hansen Road . Houston, TX 77075 . Telephone 713.943.0688 . Fax 713.944.9445 www.wattsacv.com

DIMENSIONS - ACV 1116FM (Angle)


C
120 150 180 90 60 30 0 210 240 270 300

OUTLET

D
XXXX

XX
TS AT V W AC

A A 150 Outlet 5-3/4 6-3/4 8-1/2 11 300 Outlet 6-1/8 7-1/8 8-15/16 11-1/2

INLET

E B D 300 Inlet 6-1/8 7-1/8 8-15/16 11-1/2 C 5-1/2 5-1/2 4 4 150 Inlet 17-1/2 19-1/4 24-1/2 26-3/4 300 Inlet 17-3/4 19-5/8 25 27-1/4 E 9-1/2 10 11 13 F 7.875 9.97 13.25 16.00

Valve Size Inch - MM 3 - 80 4 - 100 6 - 150 8 - 200

150 Inlet 5-3/4 6-3/4 8-1/2 11

Installation / Start-up Start-up of an Automatic Control Valve requires that proper procedures be followed. Time must be allowed for the valve to react to adjustments and the system to stabilize. The objective is to bring the valve into service in a controlled manner to protect the system from damaging overpressure. NOTE: Avoid mounting valves in a vertical discharge position (valve stem horizontal or cover pointed sideways.) Valves mounted in this position may not perform as tested and approved. - Clear the line of slag and other debris. - Install the valve so that the FLOW ARROW marked on the valve body matches the flow through the line. - Install pressure gauge (supplied) in fitting on valve tubing. Step 1: Turn the Relief Control adjustment screw counterclockwise (out). This lowers the initial relief set-point, allowing the set-point to be increased to the desired setting. Step 2: Loosen a tube fitting at a high point on the valve. This is to allow the cover to vent trapped air during initial filling of the valve. Step 3: Start the pump to supply fluid / pressure to the valve. Step 4: Tighten the tubing when all air is vented from the cover as indicated by continual flow of fluid. NOTE: THE RELIEF SET-POINT SHOULD BE LOWER THAN DESIRED AT THIS TIME. Step 5: Turn the Relief Control adjustment screw clockwise (in) slowly, allowing time for the pressure to gradually increase to the desired set-point.
rev1003

8550 Hansen Road

Houston, TX 77075

Telephone 713.943.0688

Fax 713.944.9445 www.wattsacv.com

MAINTENANCE DISASSEMBLY ASSEMBLY

Maintenance The basic valve, being of packless construction and requiring no lubrication, normally requires a minimum of maintenance. However, it is suggested that a periodic inspection schedule be established to determine how the fluid is affecting the efficiency of the valve. Fluid velocity as well as substances occurring in them such as dissolved minerals and suspended particles, vary in every installation. In areas subject to freezing, remove the body cover drain plugs for winter drain-down. NOTE: The following method will determine if there is a damaged diaphragm without removing the valve cover. Put pressure into the valve and close all control lines to the valve cover chamber. Remove a fitting on the valve cover. If there is a continuous flow our of the cover chamber through this opening, the diaphragm is damaged or the diaphragm assembly on the stem is loose. CAUTION: The valve will be wide open during this procedure. Omit if the fully open valve could result in system damage.

Disassembly / Assembly Inspection or maintenance can be accomplished without removal from the line. To replace the diaphragm and / or the quad ring: 1. Remove fitting nuts where necessary to release the valve cover from the controls or control lines. 2. Remove the cover and spring. 3. Remove the diaphragm and stem assembly taking care not to damage the diaphragm when removing over studs. 4. With the assembly removed, examine the diaphragm and quad ring for wear or damage. Do not disassemble unless replacement is indicated. 5. To replace the diaphragm, quad ring and / or stem o-ring, hold the stem in a vise or with wrench on the flats at the bottom end of the stem. Remove the nuts. 6. Remove the diaphragm wisher, diaphragm, etc. in proper sequence. 7. Check all surfaces, seat, o-ring groves and diaphragm clamping surfaces for damage and / or foreign particles. 8. To reassemble, reverse the order of disassembly. Tighten stem nuts securely to ensure proper clamping of the diaphragm. To assure positive and even clamping of the diaphragm between the body and the cover, gradually tighten the cover nuts diametrically opposite each other.

You might also like