Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
268 views

Chapter On Base Isolation in EuroCode 8 Summarized

The document discusses Eurocode 8 and its provisions for seismic base isolation of buildings. Section 10 of Eurocode 8 deals specifically with base isolation and aims to reduce seismic response by increasing period, modifying mode shape, and increasing damping. It defines key terms like isolation system, isolator units, and isolation interface. Common isolator units include laminated bearings and dampers, with functions like load capacity, energy dissipation, and recentering. Analysis methods included in the code are equivalent linear, simplified linear, modal simplified linear, and modal or time history analysis.

Uploaded by

Bayram Aygun
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
268 views

Chapter On Base Isolation in EuroCode 8 Summarized

The document discusses Eurocode 8 and its provisions for seismic base isolation of buildings. Section 10 of Eurocode 8 deals specifically with base isolation and aims to reduce seismic response by increasing period, modifying mode shape, and increasing damping. It defines key terms like isolation system, isolator units, and isolation interface. Common isolator units include laminated bearings and dampers, with functions like load capacity, energy dissipation, and recentering. Analysis methods included in the code are equivalent linear, simplified linear, modal simplified linear, and modal or time history analysis.

Uploaded by

Bayram Aygun
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 17

EUROCODES

Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

Eurocode 8 Base Isolation (for buildings)


E C Carvalho, Chairman TC250/SC8

EUROCODES
Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

EN1998-1: General rules, seismic actions and rules for buildings Section 10 - Base isolation Deals with seismically isolated structures (specific rules for buildings)
Aim: Reduce the seismic response of the lateral-force resisting system by: Increasing the Fundamental Period Modifying the shape of the fundamental mode Increasing the damping Combining various effects
Specific rules for Bridges in EN 1998-2

Distributed energy dissipation systems not covered by Section 10

EUROCODES
Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

Base isolation strategies


Period elongation Reduction of spectral accelerations Increase of displacements (mostly occurring in the isolation
system)

In both cases with increased energy dissipation capacity

EUROCODES
Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

Main Definitions
Isolation system Collection of components used for providing
seismic isolation, which are arranged over the isolation interface.

Isolation interface Surface which separates the substructure


and the superstructure and where the isolation system is located.
Normally at the base of buildings, tanks and silos or between piers and deck in bridges.

Isolator units Elements constituting the isolation system. Full isolation The structure is fully isolated if, in the design seismic
situation, it remains within the elastic range.

EUROCODES
Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

Types of Isolator units


Laminated elastomeric bearings (quasi elastic response with
equivalent damping from 5% - LDRBs to 20% - HDRBs)

Elastoplastic devices (hysteretic response of metals) Viscous or friction dampers Pendulums (low friction sliders stainless steel/PTFE)

Functions/capabilities
Vertical-load carrying capacity Energy dissipation capacity Recentering capability Lateral restraint

EUROCODES
Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

Design Objectives as for non base-isolated structures: In the event of earthquakes:


Human lives are protected Damage (structural, non-structural and to contents) is limited Structures important for civil protection remain operational

Fundamental requirements as for non base-isolated structures:


No-collapse requirement Damage limitation requirement
But an increased reliability is required for the isolating devices Magnification factor X on the seismic displacements of each unit (NDP recommended value X = 1,2)

EUROCODES
Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

Compliance criteria
For the DLS, lifelines crossing joints remain elastic For the ULS, gas lines and other hazardous lifelines crossing joints accommodate the relative displacements including the magnification factor X Interstorey drift limited as for non base isolated buildings At ULS, substructure and superstructure remain elastic

EUROCODES
Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

General Design Provisions


Arrangement of devices allowing for inspection, maintenance and replacement Protection of devices against fire, chemical or biological attack Distribution of devices to minimize torsion effects Sufficient stiffness of structure above and below the isolation interface to avoid differential movement Sufficient space around the devices to allow free movement with no hammering

EUROCODES
Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

Seismic action
Two horizontal and vertical components acting simultaneously Elastic spectrum (and alternative representations) as for nonbase isolated buildings Site specific spectra required for Class IV buildings if distance from potentially active fault with a MS 6,5 is less than 15 km
(When applicable) behaviour factor q = 1,0 except for the superstructure where q = 1,5 may be used.

EUROCODES
Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

10

Properties of isolation system For analysis purposes use the most unfavourable values of mechanical properties (account for rate of loading,
effect of vertical load, temperature and aging)

Maximum stiffness and Minimum damping for the evaluation of accelerations and forces Minimum stiffness, damping and friction for the evaluation of displacements
In Class I and II buildings mean values may be used provided that extreme values are within 15% of the mean

EUROCODES
Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

11

Structural Analysis Equivalent linear analysis Simplified linear analysis Modal simplified linear analysis Modal linear analysis Time history analysis

EUROCODES
Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

12

Equivalent linear analysis Use equivalent stiffness and damping at displacement ddc
(evaluated in an iterative procedure)

Conditions (for equivalence):


Effective (secant) stiffness of the Isolation System (at total design displacement) is not less than 50% of the effective stiffness at 0,2ddc Effective damping of the Isolation System does not exceed 30%. The force-displacement characteristics of the Isolation System do not vary more than 10% due to the rate of loading and the vertical load variation (in the range of design values) The increase of force in the Isolation System for displacements between 0,5ddc and ddc is not less than 2,5% of the total gravity load above the system (to provide recentering capability)

EUROCODES
Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

13

Simplified (static) linear analysis The structure is assumed to behave like a SDOF system in both horizontal directions (superstructure acting as a rigid block) Conditions (for simplification):
Maximum eccentricity between stiffness of the Isolation System and centre of mass of the structure does not exceed 7,5% of plan Distance from potentially active faults with MS 6,5 greater than 15 km Maximum plan dimension not greater than 50 m Rigid substructure (to minimise differential displacements) All devices above elements of substructure that support vertical load Effective period in the range: 3Tf Teff 3 s (Tf is the period for the
same structure with a fixed base)

EUROCODES
Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

14

Simplified (static) linear analysis


Conditions (for simplification) (additional for buildings):
Regularity and symmetry of the superstructure (in two axis) Negligible rocking rotation at the base Ratio between vertical and horizontal stiffness of the Isolation System: Kv/Keff 150 Rigid substructure (to minimise differential displacements) Vertical period: Tv = 2 (M/Kv) 0,1 s

EUROCODES
Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

15

Simplified (static) linear analysis


Apply static forces to the structure in two directions Horizontal forces proportional to storey masses (constant
acceleration along the height)

Torsional effects taken approximately increasing the effects in structural members according to their distance to the centre of mass (as for conventional symmetrical structures)

EUROCODES
Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

16

Modal simplified linear analysis Applicable when the conditions for the simplified (static) analysis are met except the one for maximum eccentricity
The structure is assumed to behave like a 3DOF system
(superstructure acting as a rigid block with its motion described by 2 horizontal displacements and the rotation about the vertical axis)

Modal linear analysis Applicable when the conditions for the simplified analysis are not met
A linear model of the complete structural system including both the stiffness of the superstructure (according to the modelling rules applicable to conventional structures) and the equivalent stiffness and damping properties of the isolator units should be used for a complete modal analysis

EUROCODES
Background and Applications

Brussels, 18-20 February 2008 Dissemination of information workshop

17

Time history analysis


Can always be used (any type of structure and isolation system)
Mandatory if it is not possible to model the Isolation System with an equivalent linear system The superstructure may be modelled elastically (for full isolation) The constitutive model of the devices shall represent its actual behaviour in the range of deformations and velocities associated with the seismic design situation (use the most unfavourable values) Seismic action represented as defined for time history analysis of conventional structures (alternative representations of the seismic action)

You might also like