Venturi scrubbers use the energy of an exhaust gas stream to atomize a scrubbing liquid. They are effective at removing particulate pollutants. Venturis consist of a converging section, throat, and diverging section where gas and liquid contact removes particles. Modifications allow venturis to handle varying gas flows. Venturis operate at high pressure drops and liquid-gas ratios to maximize particle collection but have short contact times, limiting gas removal unless velocities are lowered and liquid-gas ratios increased.
Venturi scrubbers use the energy of an exhaust gas stream to atomize a scrubbing liquid. They are effective at removing particulate pollutants. Venturis consist of a converging section, throat, and diverging section where gas and liquid contact removes particles. Modifications allow venturis to handle varying gas flows. Venturis operate at high pressure drops and liquid-gas ratios to maximize particle collection but have short contact times, limiting gas removal unless velocities are lowered and liquid-gas ratios increased.
Venturi scrubbers use the energy of an exhaust gas stream to atomize a scrubbing liquid. They are effective at removing particulate pollutants. Venturis consist of a converging section, throat, and diverging section where gas and liquid contact removes particles. Modifications allow venturis to handle varying gas flows. Venturis operate at high pressure drops and liquid-gas ratios to maximize particle collection but have short contact times, limiting gas removal unless velocities are lowered and liquid-gas ratios increased.
Venturi scrubbers use the energy of an exhaust gas stream to atomize a scrubbing liquid. They are effective at removing particulate pollutants. Venturis consist of a converging section, throat, and diverging section where gas and liquid contact removes particles. Modifications allow venturis to handle varying gas flows. Venturis operate at high pressure drops and liquid-gas ratios to maximize particle collection but have short contact times, limiting gas removal unless velocities are lowered and liquid-gas ratios increased.
scrubbers. This lesson will focus on these collectors that work primarily by gas-phase contacting: venturi scrubbers, plate towers, and orifice scrubbers.
Venturi Scrubbers A venturi scrubber is designed to effectively use the energy from the exhaust stream to atomize the scrubbing liquid. Venturi devices have been used for over 100 years to measure fluid flow (Venturi tubes derived their name from G. B. Venturi, an Italian physicist). About 35 years ago, Johnstone (1949) and other researchers found that they could effectively use the venturi configuration to remove particles from an exhaust stream. Figure 3-1 illustrates the classic venturi configuration.
Figure 3-1.
Venturi configuration
A venturi scrubber consists of three sections: a converging section, a throat section, and a diverging section. The exhaust stream enters the converging section and, as the area decreases, gas velocity increases. Liquid is introduced either at the throat or at the entrance to the converging section. The exhaust gas, forced to move at extremely high velocities in the small throat section, shears the liquid from its walls, producing an enormous number of very tiny droplets. Particle and gas removal occur in the throat section as the exhaust stream mixes with the fog of tiny liquid droplets. The exhaust stream then exits through the diverging
section, where it is forced to slow down. Venturis can be used to collect both particulate and gaseous pollutants, but they are more effective in removing particles than gaseous pollutants. Liquid can be injected at the converging section or at the throat. Figure 3-2 shows liquid injected at the converging section. Thus, the liquid coats the venturi throat making it very effective for handling hot, dry exhaust gas that contains dust. Otherwise, the dust would have a tendency to cake on or abrade a dry throat. These venturis are sometimes referred to as having a wetted approach.
Figure 3-3 shows liquid injected at the venturi throat. Since it is sprayed at or just before the throat, it does not actually coat the throat surface. These throats are susceptible to solids buildup when the throat is dry. They are also susceptible to abrasion by dust particles. These venturis are best used when the exhaust stream is cool and moist. These venturis are referred to as having a non-wetted approach.
Liquid inlet
Liquid inlet
Throat
Figure 3-3.
Venturi with throat sprays
Venturis with round throats (Figures 3-2 and 3-3) can handle exhaust flows as large as 88,000 m3/h (40,000 cfm) (Brady and Legatski 1977). At exhaust flow rates greater than this, achieving uniform liquid distribution is difficult, unless additional weirs or baffles are used. To handle large exhaust flows, scrubbers designed with long, narrow, rectangular throats (Figure 3-4) have been used.
Simple venturis have fixed throat areas and cannot be used over a wide range of gas flow rates. Manufacturers have developed other modifications to the basic venturi design to maintain scrubber efficiency by changing the throat area for varying exhaust gas rates. Certain types of orifices (throat areas) that create more turbulence than a true venturi were found to be equally efficient for a given unit of energy consumed (McIlvaine Company 1974). Results of these findings led to the development of the annular-orifice, or adjustable-throat, venturi scrubber (Figure 3-5). The size of the throat area is varied by moving a plunger, or adjustable disk, up or down in the throat, thereby decreasing or increasing the annular opening. Gas flows through the annular opening and atomizes liquid that is sprayed onto the plunger or swirled in from the top.
Another adjustable-throat venturi is shown in Figure 3-6. In this scrubber, the throat area is varied by using a movable plate. A water-wash spray is used to continually wash collected material from the plate.
Another modification can be seen in the venturi-rod or rod deck scrubber. By placing a number of pipes parallel to each other, a series of longitudinal venturi openings can be created as shown in Figure 3-7. The area between adjacent rods is a small venturi throat. Water sprays help prevent solids buildup. The principal atomization of the liquid occurs at the rods, where the high-velocity gas moving through spacings creates the small droplets necessary for fine particle collection. These rods must be made of abrasion-resistant material due to the high velocities present.
Figure 3-7.
Venturi-rod scrubber
All venturi scrubbers require an entrainment separator because the high velocity of gas through the scrubber will have a tendency to exhaust the droplets with the clean gas stream. Cyclonic, mesh-pad, and blade separators (described in more detail in Lesson 8) are all used to remove liquid droplets from the flue gas and return the liquid to the scrubber water. Cyclonic separators, the most popular for use with venturi scrubbers, are connected to the venturi vessel by a flooded elbow (Figure 3-8). The liquid reduces abrasion of the elbow as the exhaust gas passes at high velocities from the venturi to the separator.
Particle Collection Venturis are the most commonly used scrubber for particle collection and are capable of achieving the highest particle collection efficiency of any wet scrubbing system. As the exhaust stream enters the throat, its velocity increases greatly, atomizing and turbulently mixing with any liquid present. The atomized liquid provides an enormous number of tiny droplets for the dust particles to impact on. These liquid droplets incorporating the particles must be removed from the scrubber exhaust stream, generally by cyclonic separators. Particle removal efficiency increases with increasing pressure drop because of increased turbulence due to high gas velocity in the throat. Venturis can be operated with pressure drops ranging from 12 to 250 cm (5 to 100 in.) of water. Most venturis normally operate with pressure drops in the range of 50 to 150 cm (20 to 60 in.) of water. At these pressure drops, the gas velocity in the throat section is usually between 30 and 120 m/s (100 to 400 ft/sec), or approximately 270 mph at the high end. These high pressure drops result in high operating costs. The liquid-injection rate, or liquid-to-gas ratio (L/G), also affects particle collection. The proper amount of liquid must be injected to provide adequate liquid coverage over the throat area and make up for any evaporation losses. If there is insufficient liquid, then
there will not be enough liquid targets to provide the required capture efficiency. Most venturi systems operate with an L/G ratio of 0.4 to 1.3 L/m3 (3 to 10 gal/1000 ft3) (Brady and Legatski 1977). L/G ratios less than 0.4 L/m3 (3 gal/1000 ft3) are usually not sufficient to cover the throat, and adding more than 1.3 L/m3 (10 gal/1000 ft3) does not usually significantly improve particle collection efficiency.
Gas Collection Venturi scrubbers can be used for removing gaseous pollutants; however, they are not used when removal of gaseous pollutants is the only concern. The high exhaust gas velocities in a venturi result in a very short contact time between the liquid and gas phases. This short contact time limits gas absorption. However, because venturis have a relatively open design compared to other scrubbers, they are very useful for simultaneous gaseous and particulate pollutant removal, especially when: Scaling could be a problem A high concentration of dust is in the exhaust stream The dust is sticky or has a tendency to plug openings The gaseous contaminant is very soluble or chemically reactive with the liquid
To maximize the absorption of gases, venturis are designed to operate at a different set of conditions from those used to collect particles. The gas velocities are lower and the liquid-to-gas ratios are higher for absorption. For a given venturi design, if the gas velocity is decreased, then the pressure drop (resistance to flow) will also decrease and vice versa. Therefore, by reducing pressure drop, the gas velocity is decreased and the corresponding residence time is increased. Liquid-to-gas ratios for these gas absorption applications are approximately 2.7 to 5.3 L/m3 (20 to 40 gal/1000 ft3). The reduction in gas velocity allows for a longer contact time between phases and better absorption. Increasing the liquid-to-gas ratio will increase the potential solubility of the pollutant in the liquid.
Maintenance Problems The primary maintenance problem for venturi scrubbers is wear, or abrasion, of the scrubber shell because of high gas velocities. Gas velocities in the throat can reach speeds of 430 km/h (270 mph). Particles and liquid droplets traveling at these speeds can rapidly erode the scrubber shell. Abrasion can be reduced by lining the throat with silicon carbide brick or fitting it with a replaceable liner. Abrasion can also occur downstream of the throat section. To reduce abrasion here, the elbow at the bottom of the scrubber (leading into the separator) can be flooded (i.e. filled with a pool of scrubbing liquid). Particles and droplets impact on the pool of liquid, reducing wear on the scrubber shell. Another technique to help reduce abrasion is to use a precleaner (i.e., quench sprays or cyclone) to remove the larger particles. The method of liquid injection at the venturi throat can also cause problems. Spray nozzles are used for liquid distribution because they are more efficient (have a more effective spray pattern) for liquid injection than weirs. However, spray nozzles can easily plug when liquid is recirculated. Automatic or manual reamers can be used to correct this problem. However, when heavy liquid slurries (either viscous or particle-loaded) are recirculated, open-weir injection is often necessary. Table 3-1 summarizes some of the operational problems associated with venturi scrubbers. Table 3-1. Problem Low efficiency
Operational problems associated with venturi scrubbers
Probable cause Low scrubbing-liquid flow rate Low pressure drop Corrective action Check for plugged pipe or nozzles, incorrectly opened valves, or overthrottled pump-discharge valve. Check for low scrubbing liquor, low gas flow; inoperative or uncalibrated variable-throat controller; damaged variable-throat blade or disk. Check washdown sprays, spray liquor composition, and pH (for scaling). Check for damper setting or venturi throat setting.
Partially blocked entrainment separator Excessive gas flow Inlet dust loading or particle size distribution different from that for which scrubber is designed
(continued) problems associated with venturi scrubbers
Probable cause Low scrubbing-liquid rate
Operational
Corrective action Check for plugged pipe or nozzles, incorrectly opened valves, or overthrottled pump-discharge valve. Check and adjust makeup or heatexchanger liquid flow rates. Check quench sprays, if applicable, or upstream equipment. Check washdown sprays and spray pattern; use more flushing periods if necessary. Check liquor chemistry for scaling agents. Clean drain; add flushing water to continuously irrigate drain pipe. Reduce gas flow. Modify strainer/nozzle opening ratio so that nozzle holes are at least twice the diameter of strainer openings. Check bleed line for malfunctions; check for excessive dust loading. Check strainers. Remove abrasives or install abrasionresistant linings. Check separation equipment. Check for excessive dust loading in gas stream and for purge-line malfunctioning. Remove abrasives from liquor stream or install abrasion-resistant linings in wear zones. Add alkali for pH modification. Check bleed line for malfunctions. Check for excessive dust loading. Check strainers. Check throat pressure drop. Check separation equipment. Check for excessive dust loading in gas stream and for purge-line malfunctioning. Add alkali for pH modification. Install abrasion-resistant liners in high-wear zones if liquor modifications are not practical. Continued on next page
High exit-gas temperature
High water-inlet temperature High inlet-gas temperature Exhaust gas liquor entrainment Plugged entrainment separator
Plugged moistureeliminator drain Excessive gas flow Plugging or excessive wear of spray nozzles Nozzle openings too small Solids concentration too high in spray liquor Abrasives in spray liquor Low pH in combination with abrasives is causing erosion or corrosion
(continued) problems associated with venturi scrubbers
Probable cause Throat-mover malfunction Sensor signal incorrect
Operational
Corrective action Remove from service; repair or replace Check sensor taps for solids buildup. Check transmission tubing for liquid buildup or air leaks. Clean or repair sensor. First make external inspection of drive train. If damaged area is not observed, shut unit down and make internal inspection using a throat-actuator manual override. Check for packing damage and excessively tight packing gland. Repair. Check gas flow against design. Check and, if necessary, adjust fan belt or speed. Check inlet duct for obstructions. Check fan damper and variable-throat opening. Check for plugged pipe or nozzles, incorrectly opened valves, or overthrottled pump-discharge valve. Install special inlets. Reduce dissolved solids in scrubbing liquor. Devote routine maintenance to removal of buildup.
Erratic automatic-throat operation
Damaged damper-disk mechanism
Low pressure drop
Broken, leaking, or plugged static-tap line Low gas-flow rate
Fan overloads and shuts off
Excessive flow rate through fan Low scrubbing-liquor flow rate
Wet-dry interface buildup
Particle buildup where gas goes from unsaturated to saturated condition
Sources: Kelly 1978 and Anderson 2000 Co.
Summary Venturi scrubbers can have the highest particle collection efficiencies (especially for very small particles) of any wet scrubbing system. They are the most widely used scrubbers because their open construction enables them to remove most particles without plugging or scaling. Venturis can also be used to absorb pollutant gases; however, they are not as efficient for this as are packed or plate towers (discussed later). The operating characteristics of venturi scrubbers are listed in Table 3-2.
Liquid-to-gas ratio (L/G) 2.7-5.3 L/m3 (20-40 gal/1000 ft3) < 7-100 kPa (< 1-15 psig) Liquid-inlet pressure (p ) L
Pollutant Gases
Pressure drop (p) 13-250 cm of water (5-100 in. of water)
Removal efficiency (%) 30-60% per venturi, depending on pollutant solubility
Particles
50-250 cm of water [50-100 cm of water is common] (20-100 in. of water) [20-60 in. of water is common]
0.4-2.7 L/m3 (3.0-20.0 gal/1000 ft3) [90-99% is typical]
Venturi scrubbers have been designed to collect particles at very high collection efficiencies, sometimes exceeding 99%. The ability of venturis to handle large exhaust volumes at high temperatures makes them very attractive to many industries; consequently, they are used to reduce particulate emissions in a number of industrial applications. This ability is particularly desirable for cement kiln emission reduction and for control of emissions from basic oxygen furnaces in the steel industry, where the exhaust gas enters the scrubber at temperatures greater than 350C (660F). Venturis are also used to control fly ash and sulfur dioxide emissions from industrial and utility boilers. A list of performance data for venturi scrubbers is given in Table 3-3. Table 3-3. Performance data of typical venturi scrubbers Typical particlesize range (m) p (in. H2O) Average collection efficiency (%)
Application Iron and steel Electric furnace
Dust
Ferromanganese and ferro silicon Iron oxide Iron, coke, and silica
