website:http://biz.LGservice.com e-mail:http://www.LGEservice.com/techsup.

html

DLP Projection TV SERVICE MANUAL

CHASSIS : NB-03JC

MODEL : RU-44SZ61D RU-52SZ61D

CAUTION
BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

SAFETY PRECAUTIONS
1. Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items: a. Be sure that no built-in protective devices are defective and/or have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assemblies in the cabinet, be sure to put back in place all protective devices, including, but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the picture tube and the cabinet back, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover. c. Antenna Cold Check-With the instrument AC plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer. Repeat this test with the instrument AC switch in the off position. d. Leakage Current Hot Check -With the instrument completely reassembled, plug the AC line cord directly into a 120 V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1 4 1 0 ,( 5 0 . 7 ) . With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal waterpipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle bracket, metal cabinet, screwheads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milliamp. Reverse the instrument power cord plug in the outlet and repeat the test. ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER. they are serviced. (X-radiation protection circuits also may be called "horizontal disable" or "hold-down.") Read and apply the high voltage limits and, if the chassis is so equipped, the X-radiation protection circuit specifications given on instrument labels and in the Product Safety & Xradiat ion Warning note on the service data chassis schematic. High voltage is maintained within specified limits by close-tolerance safety-related components/adjustments in the high-voltage circuit. If high voltage exceeds specified limits, check each component specified on the chassis schematic and take corrective action. 2. Read and comply with all caution and safety-related notes on or inside the receiver cabinet, on the receiver chassis, or on the picture tube. 3. Design Alteration Warning- Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to, circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and will make you, the servicer responsible for personal injury or property damage resulting therefrom. 4. Picture Tube Implosion Protection Warning-The picture tube in this receiver employs integral implosion protection. For continued implosion protection, replace the picture tube only with one of the same type and number. Do not remove, install, or otherwise handle the picture tube in any manner without first putting on shatterproof goggles equipped with side shields. People not so equipped must be kept safely away while picture tubes are handled. Keep the picture tube away from your body. Do not handle the picture tube by its neck. Some "in-line" picture tubes are equipped with a permanently attached deflection yoke; because of potential hazard, do not try to remove such "permanently attached" yokes from the picture tube. 5. Hot Chassis Warning-a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord and may be safely serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0 V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground. b. Some TV receiver chassis normally have 85 V AC (RMS) between chassis and earth ground regardless of the AC plug polarity. These chassis can be safely serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection. c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered. 6. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts- be sure that leads and components do not touch, c. the AC supply, d. high voltage, and e.antenna wiring. Always inspect in all areas for pinched, out-of-place, or frayed wiring. Do not change spacing between components, and between components and the printed circuit board. Check the AC power cord for damage. 7. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard. 8. PRODUCT SAFETY NOTICE Some electrical and mechanical parts have special safety related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by shading, by a , or by on schematics and parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement parts might create shock, fire, and/or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate.

AC Leakage Test
LEAKAGE CURRENT TESTER

(READING SHOULD NOT BE ABOVE 0.5mA)

DEVICE UNDER TEST TEST ALL EXPOSED MET AL SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)

+ -

EARTH GROUND

e. X-Radiation and High Voltage Limits-Because the picture tube is the primary potential source of X-radiation in solid-state TV receivers, it is specially constructed to prohibit X-radiation emissions. For continued Xradiation protection, the replacement picture tube must be the same type as the original. Also, because the picture tube shields and mounting hardware perform an X-radiation protection function, they must be correctly in place. High voltage must be measured each time servicing is done that involves B+, horizontal deflection, or high voltage. Correct operation of the X-radiation protection circuits also must be reconfirmed each time

- 2 -

TABLE OF CONTENTS
SPECIFICATIONS.................................................................4 DESCRIPTION OF CONTROLS ...........................................5 ADJUSTMENT INSTRUCTION...........................................13 BLOCK DIAGRAM...............................................................19 EXPLODED VIEW..........................................................24,26 EXPLODED VIEW PARTS LIST ....................................25,27 REPLACEMENT PARTS LIST ............................................28 SCHEMATIC DIAGRAM.......................................................... PRINTED CIRCUIT BOARDS .................................................

- 3 -

SPECIFICATIONS

Models RU-44SZ61D Horizontal Size (Inches) Height (Inches) Depth (Inches) Weight (lbs.) Horizontal Size (Inches) Height (Inches) Depth (Inches) Weight (lbs.) AC 120V, 60Hz American TV Standard, NTSC, ATSC with STB VHF: 2 - 13 UHF: 14 - 69 CATV: 1 - 125 270W 75 ohm External Terminal for VHF/UHF 15W x 2 Remote control, 2 size AA batteries. Video input (3 set) Video output (1 set) S-Video input (2) Component input (2 set) RGB input (1) DVI input (1) RGB/DVI audio input (1 set) Variable audio output (1 set) Audio center mode input (1) Calibration port (1) 41.7 30.1 14 64 48.6 35.1 15.3 80

RU-52SZ61D

Power Requirement Television System Television Channels

Power Consumption (W) Antenna Audio Output (W) Supplied Accessories External Input/Output Ports

Design and specifications are subject to change without prior notice.

- 4 -

DESCRIPTION OF CONTROLS
Function Status Indicators

Lamp indicator, operation indicator, and temperature indicator located below the front panel controls, reveal the operating status of the DLP projection TV.

Operation Indicator

Temperature Indicator

Lamp Indicator

Operation Indicator

Off Red Green Orange (flashing) Orange Red (flashing) Green (flashing) Orange Red Red (flashing)

Lamp Indicator

Temperature Indicator

Power cord is not connected. Power Cord is connected, TV is in standby mode. On Preparing operation in standby mode. Projection lamp is reaching the end of its life and needs to be replaced with a new lamp. There is a problem with the lamp or around it. Contact an authorized service center. The lamp cover is not closed. The projection TV is overheating. The projection TV shut down due to overheating. The projection TV shut down, check the cooling fan.

- 5 -

DESCRIPTION OF CONTROLS
Rear Connections Panel
Connecting cables and external equipment to your TV. This manual explains the features available on the RU-52SZ61D TVs.

ANT IN + 75

RF Connector: Antenna Used to connect analog cable or antenna signals to the television, either directly or through your cable box. S-VIDEO In A connection available with some high-end equipment that provides even better picture quality for Video 2. Video 1 or 2 Connects the video signals from various types of equipment. Left/Right Audio Used for stereo sound from various types of equipment.

RGB INPUT

PC/DTV (XGA /480p /720p /1080i) C A L I B R A T I O N COMPONENT INPUT2 INPUT1

RGB/DVI INPUT

S-VIDEO

PC and HD-STB Input Used to connect from a PC source or HD-STB Satellite system.

MONITOR OUT

VIDEO INPUT 2

VIDEO INPUT 1 VIDEO

(L) AUDIO

PB

(R) MONO

(L) AUDIO (R)

PR PC/DTV (XGA /480p /720p /1080i) (L)

DVI INPUT

AUDIO CENTER MODE IN

AUDIO (R) DTV/DVD INPUT

V A R AUDIO I A B (R) L E (L)

A U D I O O U T

Monitor Out Connects to a second TV or Monitor.

Y, Pb, Pr DVD Component Video and HD Component Video Some top-of-the-line DVD players use what is called component video, for extremely accurate picture reproduction. Refer to your DVD manual for further information.

PC and HD-STB Audio Input Used for audio connections from a PC source or HD-STB Satellite system.

Variable Audio Out Used to connect either an external amplifier, or add a sub-woofer to your surround sound system.

Audio Center Mode In Connect to external Dolby Digital Center preamp output.

Mini glossary
JACK A connection on the back of a TV, VCR, or any other A/V device. This includes the RF jack and the Audio/Video jacks that are color-coded.

SIGNAL Picture and sound traveling through cable, or over the air, to your television screen.

- 6 -

DESCRIPTION OF CONTROLS

Front Connection Panel

There are four jacks on the left front side behind the screen on your projection TV that make connecting Audio/Video devices like video games and camcorders very simple. The jacks are like those found on the back jack connection panel. This means that most equipment that connects to those types of jacks on the rear jackpack, may be connected to the front connection panel. To use the front jacks as the signal source, select them using Main Input menu as described on page 25. They will be named Front Video in the Main Input menu.

If you select either Front Video or Front S-Video, the Front audio inputs are automatically selected as well. If youre connecting a video game device, make sure to change the picture settings with the EZ Picture option in the Video menu.
Left/Right Audio Used for stereo sound from various types of equipment. Video Connects the video signals from any piece of equipment.

Front A/V Panel

(R)

AUDIO
(L)/ MONO

VIDEO

S-VIDEO

FRONT A/V

S-Video A connection available on some very high-end equipment that provides better picture quality than video input.

Mini glossary
A/V CABLESAudio/Video cables. Three cable connectorRight audio (red), Left audio (white), and Video (yellow). A/V cables are used for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices. A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box, or television).

- 7 -

DESCRIPTION OF CONTROLS

ANT / Cable Service Hookup

Cable TV Wall Jack Panel Antenna

1 2

Connect an antenna and/or cable service to your TV as shown. Turn to page 22 to do a channel search with EZ Scan for Ant/Cable connection(s).
RF Coaxial Wire (75 ohm) RF Coaxial Wire (75 ohm)

ANT IN + 75

S-VIDEO

MONITOR OUT

VIDEO INPUT 2

VIDEO INPUT 1 VIDEO

(L) MONO AUDIO (R)

If you receive your RF signal through an antenna that is several years old and connects with two small prongs, you will need to purchase a 300 to 75 ohm adapter. It should be available from your local electronics dealer. We recommend using a 75 ohm cable for your antenna connections in order to prevent interference.

For best signal reception, it is recommended to have your Antenna professionally adjusted.

- 8 -

DESCRIPTION OF CONTROLS

Remote Control Functions in TV Mode

MODE
Selects the remote operating mode: TV, VCR, Cable, DVD and Satellite. Select other operating modes, for the remote to control external devices.

INDICATOR LIGHTS
TV MODE VCR CABLE DVD SAT LIGHT POWER

TV/VIDEO
Selects: Analog, Video1, Video2, Front video, Component1-2, RGB, and DVI input sources.

Show active remote mode every time any button is pressed.

LIGHT
Illuminates the remote control keys.

FRONT
Selects the front video signal if a device, such as a camcorder or game player, is connected to the front video input jack.

TV/VIDEO COMP1

FRONT COMP2

DVI

DVI
RGB

Selects: DVI-DTV and DVIPC input sources.

MUTE
Switches the sound on or off

1 4 7
ENTER
MUTE

2 5 8 0

3 6 9
FLASHBK
SURF

SURF
Scrolls the Surf channel list.

SAP
Selects: Mono, Stereo, and SAP.

VIDEO
Adjusts the factory preset picture according to the room.

PIP
Toggles between PIP, POP (Picture-out-of-Picture) and Twin picture mode.
SAP
VOL CH

VIDEO

SWAP
Switches the picture from PIP, POP, or twin picture to the main screen.

PIP

PIPCH- PIPCH+ SWAP

PIPCHChanges to next lower PIP channel

RATIO CC FREEZE PIP INPUT

PIPCH+
Changes to next higher PIP channel.

THUMBSTICK
Allows you to navigate the on-screen menus and to adjust the system settings and preferences, by moving to D an option withF E G and selecting the highlighted option with .
MENU EXIT

FREEZE
Captures and freezes the currentlyviewed main picture in PIP mode.

MENU
Brings up the main menu to the screen.
PLAY PAUSE STOP RECORD

EXIT
Clears all on-screen displays and returns to TV viewing from any menu.

REW

FF SKIP

- 9 -

DESCRIPTION OF CONTROLS

Remote Control Functions in TV Mode

TV MODE

VCR CABLE DVD SAT LIGHT POWER

POWER
TV/VIDEO COMP1 FRONT COMP2 DVI RGB

Turns your TV or any other programmed equipment on or off, depending on mode.

COMPONENT 1, 2
Selects component signal sources, such as DVD or HD receiver.

RGB

1 4 7
ENTER
MUTE

2 5 8 0

3 6 9
FLASHBK
SURF

Selects: RGB-DTV and RGB-PC input sources.

NUMBER KEYPAD
For direct channel selection and programming functions.

ENTER
When in the menu system and other on-screen displays, selects highlighted options.

FLASHBK
Tunes to the last channel viewed.

SAP

VIDEO
VOL CH

VOLUME UP/DOWN
Increases/decreases the sound level.
PIP

CHANNEL UP/DOWN
Scrolls through available channels in EZ Scan memo-

PIPCH- PIPCH+ SWAP

RATIO
Changes the screen format or aspect ratio.

RATIO

CC

FREEZE PIP INPUT

PIP INPUT
Selects the input source for the sub picture.

CC
Selects a closed caption mode for displaying captioning information if available on program.
MENU EXIT

ENTER
When in the menu system and other on-screen displays, selects highlighted options.

PLAY PAUSE STOP RECORD

RECORD, PAUSE, REW, FFWD, PLAY, STOP

Control the functions on your VCR.

REW

FF

SKIP
SKIP

Playing CDs: Selects songs. Playing DVDs: Selects movie chapters.

- 10 -

DESCRIPTION OF CONTROLS
On-Screen Displays

This page describes your on-screen display and information banner options.

Main Channel Display Displays current channel number.

Channel Label If a channel label has been set, then it will appear here.

TV 13
MONO

ABC

PIP Display This display appears when PIP is active.

TV 6

AM 03:00 10

Mute Appears when sound is muted.

Volume Volume level is displayed while adjusting the sound.

Time Appears when pressing the enter button on remote control.

- 11 -

DESCRIPTION OF CONTROLS
Front Panel Controls

POWER

MENU

ENTER

VOL

CH

1 2 1 2 3 4 5 6 7 8
POWER MENU

6 7

ENTER (Same as ENTER button on your remote control) VOLUME UP / DOWN CHANNEL UP / DOWN Operation indicator. Lamp indicator. Temperature indicator. See menu pages for instructions on using the onscreen menus. The POWER, CHANNEL, TV/VIDEO, and VOLUME buttons work just as they do on your remote control. If TV is moved from cold to normal room temperature, humidity may form inside TV, wait 3 hours for TV to adjust to room temperature before turning it on.

- This manual explains the features available on the RU-52SZ61D TVs.

- 12 -

ADJUSTMENT INSTRUCTIONS
1. Application Object
This instruction is for the application to the DLP Projection TV(Chassis: NB-03JC). (4) Adjust the value of adjustment with using the volume +(F),volume -(G) key. (5) Press the ADJ key to come out after adjustment. (6) Preparation for Adjustment 1) Connect the power to TV Set and set the status of Power on. 2) Heat-Run must operate over 5 minitues before adjustment.

2. Notes
(1) The power source insulation of this DLP Projection is not charging type and you may not use the transformer for insulation. But youd better adjust the set after operating it with insulation transformer between power supply cable and input part of the set for protecting the adjusting equipments. (2) The adjustment must be performed under the correct sequence. (3) The adjustment must be performed in the circumstance of 25 5C of temperature and 65 10% of relative humidity if there is no specific designation. (4) The input voltage of the receiver must keep 110V, 60Hz in adjusting. (5) The set must be operated for 5 minutes preliminarily before adjustment if there is no specific designation. The preliminary operation must be performed after receiving 100% white pattern,but reception of the moving picture may also be possible in unavoidable case.

4. Driver Board Bin Setting

See Bias Voltage Bin on the DMD as shown Fig 2 and adjust the switch on the lower Driver Board as shown Fig 3.

<Fig 2> DMD Marking Locations

3. Composition of Adjustment Mode

(1) All adjustment mode are entered by pressing the ADJ key on the remore control,after adjustment pess the ADJ key to come out. (2) Below picture is screen composition when press the first ADJ key. <Fig 3> Driver Board Bin Setting

5. Adjustment the optical engine

C <Fig 4> <Fig 1> Adjustment Mode OSD (3) Select menu to adjust with using (CH+(D),CH-(E)) key above screen and press Enter key or Volume+(G)key to adjust on the wanting menu. (1) After placing the optical enging on the JIG, adjust illuminator by adjuting the A, B, and C as shown Fig 4.

- 13 -

ADJUSTMENT INSTRUCTIONS
1) The screen change when adjusting the A - When fasten the screw: Fall out the upper/right illuminator - When loosen the screw: Fall out the lower/left illuminator 2) The screen change when adjusting the B - When fasten the screw: Fall out the lower illuminator - When loosen the screw: Fall out the upper illuminator 3) The screen change when adjusting the C - When fasten the screw: Fall out the upper/left illuminator - When loosen the screw: Fall out the lower/right illuminator
Check the spot (phenomenon such as Light tunnel exit) on the edge of the white screen as shown Fig 5.

1) The pattern when adjustment

<Fig 7.> 2) Adjust the 4 gold ellipse to focus as same level. 3) If you cant check the DMD cell bourder at red center position after adjustment, regard as NG. 4) The magnified pattern for checking the focus adjustment

<Fig 5> (2) After adjustment the illuminator, adjust the focus using the focus adjustment screw of projection lens. After fasten the nut tightenly, inject the resilock. (Fig. 6)

6. Caution for DMD(Digital Micro-mirror Device)

6-1. Caution for DMD ESD
(1) You connect the grounding to prevent ESD (Electrostatic Discharge) when handing the DMD. (2) The worker have to wear wrist strap that connect to ground. (3) Electric workshop and an electric conductor surface connect to ground. (4) Save the DMD after removement a static electricity. Keep it at an exclusive case when moving it. When grounding, open the case. (5) Put on gloves that to prevent static electricity. If its old, replace it. (6) The work is done at the electro static-free location. Attach the tape or remove dust on the front or back pin of DMD glass.

<Fig 6> * Caution: The focus check position is not the center screen but to be same proportion about upper/lower screen.

- 14 -

ADJUSTMENT INSTRUCTIONS
6-2. Caution
(1) Keep the procedure and caution to prevent the screen strange phenomenon. Dont make a scratch. (2) When DMD stains with dust, polish the front and back DMD with soft wiper. Then, polish the front and back DMD after rotating 180 degree the DMD. If necessary, take a inspection. (3) Dont clean the DMD with the high pressure. Because the electric static and pollution influence to DMD.

<Fig 8> How to connect the MEMORY JIG and PC

7. EDID Data Input

7-1. Required Test Equipment
(1) A jig for adjusting PC, DDC. (PC serial to D-sub. Connection equipment) (2) S/W for writing DDC (EDID data write & read) (3) D-sub terminal

8-2. Adjustment Sequence

(1) After program running, displayed [OPTION MODE SELECTION] window. Check the Load configuration File(.cdf, .pdr) in this window and click the finish button (2) When the screen displays the open window, select the suitable file(*.cdf) according to model. (3) IC figure is change to green by clicking it. (Fig. 9)

7-2. Setting of Devices

DLP PJTV SET (or Digital Board) JIG

PC

7-3. Preparation for Adjustment

(1) Set devices as above and turn the PC, jig on. (2) Put the S/W for writing DDC (EDID data write & read) into operation.

7-4. Sequence of Adjustment

(1) Put the SET(or Digital Board) on the table and turn the power on. (2) Input the product code, production week / year, serial number (if it is not input, write 01) to the S/W for writing DDC. (3) Put the EDID write instruction into operation.

8. CPLD Download Work

8-1. Required Test Equipments & Preparation for Adjustment
(1) Connect the PC and memory JIG as shown (fig8). (2) Turn on JIG MAIN POWER SW. (3) After turn on the PC and moniter, operate the device programming. <Fig.9> (4) Select the program of operations. (5) Check the [Erase before programming] and [Verify] menu as shown <Fig4> and press the OK button. (6) At this time, the download starts. The download finished after 10 seconds.

- 15 -

ADJUSTMENT INSTRUCTIONS
(2) Select menu with using Volume- (F) key or Volume+ (G) key on the Country. (USA/CA.)

11. Screen Position Adjustment

11-1. Required Test Equipments
Remote control of adjustment

11-2. Horizontal Position Adjustment

(1) Press ADJ key on the remote control to enter the adjustment mode. (2) Select the POSITION of the adjustment menu. (H: 200) (3) Select the H_position of the Adjust Mode. (4) Adjust data with using the left/right key on the remote control in order to be left/right semmetry screen. (5) After adjustment over, recieve PAL-B/G Digital and chedk the adjusmen level.

<Fig 10>

9. Component AD9883A Offset/Gain Adjustment

9-1. Required Test Equipments
Remote control for adjustment, 801GF or 802F

<Fig11> 720P/50Hz HozTVBar Pattern <Fig 12> Pattern for screen adjustment

9-2. Preparation for Adjustment

(1) Connect a power source with TV Set and turn TV set on. (2) Do Heat-Run for 5 minutes and over before adjustment. (3) Receive the Component 1 or 2. (4) Receive the 720P/50Hz, HozTVBar Pattern of 801GF /802F. (Fig. 11)

11-3. Vertical Position Adjustment

(1) Select V-position. (V: 15) (2) Change the data to symmetrized upper and down of screen (refer to Fig12) and then press the Volume key on Remote control to get out of adjustment mode.
Adjustment 31 Line

9-3. Offset/ Gain Adjustment

(1) Press Adjust key on the remote control to enter the adjustment mode after more than 10 seconds of receiving the signals. (2) Press 4.AD9883 Adjust to adjust. (3) When the OSD of End of AD9883 Adjust appeared and disappears, the adjustment is completed

10. System Option Adjustment

10-1. Required Test Equipments
Remote control for adjustment

10-2. System Option Adjustment

(1) Enter the System Option adjustment mode on the adjust mneu by pressing Volume+ (G) key.
Adjustment 254 Line

<Fig 13>

- 16 -

ADJUSTMENT INSTRUCTIONS
12. White Balance Adjustment
(Day Light Mode) : R fixation (4) Check the RED Pattern to uniform. After checking unless abnormality do OK.

12-1. Required Test Equipments

CA100 or CA210

(color wheel index)

CWI

160

12-2. White basse balue(Medium)

x = 0.283 0.01, y = 0.297 0.01

12-3. Adjustment Sequence

(1) Install the equipment(CA110 or CA210) be 20cm away from screen center. (2) Select White balance by pressing ADJ Mode Key on Remote control. (3) Warm(6500cK) : x = 0.313, y = 0.329 1) R Gain 120 fixation 2) Adjust white balance changing G, B gain. (Gain default: R-120, G-110, B-100) 3) Offset fixation R/G/B --> -29, -28, -24 (4) Medium(9300cK) : x = 0.283, y = 0.297 1) R Gain 110 fixation 2) Adjust white balance changing G, B gain. (Gain default: All 110) 3) Offset fixation R/G/B --> -26, -25, -24 (5) Cool(12000cK) : x = 0.275, y = 0.277 1) R Gain 110 fixation 2) Adjust white balance changing G, B gain. (Gain default: R-110, G-110, B-120) 3) Offset fixation R/G/B --> -25, -24, -24 * Reference : Gamma table -> 2 Brightness -> 200Level Spoke Func. -> 0 R/G/B offset -> It has each color temperature fixation price
(color wheel index)

<Fig 14> TEST Pattern(Lamp Gray Pattern)

(color wheel index)

CWI

162

starting point of noise (appearance GREEN)

CWI

160

13. CWI Adjustment

13-1. Required Test Equipments
Remote control for adjustment <Fig 15> TEST Pattern(RED Pattern)

13-2. Preparation for Adjustment

(1) Connect the power at TV set to turn set on (2) Using the remote control, enter from ADJUST to CWI. (160) * As temperature is different sensitivity, change angle of the color wheel. At this time, the adjustment is done because color may be changed.

13-3. Adjustment Sequence

(1) Using the Volume key, adjust CWI to the left/right (2) As adjustment, check the appearance noise in the TEST Pattern. Setting the value reduced 3~4 step at a GREEN noise disappearing spot. (3) Using CH UP/DOWN key of th remote control, enter the RED PATTERN.

- 17 -

ADJUSTMENT INSTRUCTIONS
14. Main/Sub Contrast Adjustment
Adjust which it sees last prosecuting attorney time the screen contrast difference. Basically the letter does with the fact that the character and distinction become.

14-1. Preparation for Adjustment

(1) Receive signal(RF 06Ch.) on the Main/Sub screen in the twin picture. (2) Confirms picture probably is the normal.

14-2. Adjustment Sequence

(1) Main Screen Adjustment
1) Select the VPX3226 by pressing ADJ key on the remote control for adjustment. 2) Select the Contrast(m) of adjustment item using CH +/key and revises using VOL +/- key. (Initial data: 32)

(2) Sub Screen Adjustment

1) Select the VPX3226 by pressing ADJ key on the remote control for adjustment. 2) Select the Contrast(s) of adjustment item using CH +/key and revises using VOL +/- key. (Initial data: 32) * When revising, the case above 2 being changed from initial data requests Irrigation.

- 18 -

BLOCK DIAGRAM

- 19 -

BLOCK DIAGRAM

- 20 -

BLOCK DIAGRAM

- 21 -

BLOCK DIAGRAM

- 22 -

NOTES

- 23 -

400 410 411

430 401 310 431 311 434 432 433 308 309 700 404 681 680 402

305

300

650

301

EXPLODED VIEW(44)

- 24 660 420 121 503 530 502 570 601 590 571 174 630 540 520 550 720 600
621

670

403

120

303

304

302 572
620

501

560 612 610 622 623 640 641 611

602

EXPLODED VIEW PARTS LIST

No. 120 121 174 300 301 302 303 304 305 308 309 310 311 400 401 402 403 404 410 411 420 430 431 432 433 434 501 502 503 520 530 540 550 560 570 571 572 590 600 601 602 610 611 612 620 621 622 623 630 640 641 650 660 670 680 681 700 720 Part No. 6400WESC01A 6400DESA01A 6410VUH004A 3091V00582B 5020V00870B 4811V00070C 3550V00348B 3550V00350A 3351V00009A 4980V00822B 4980V00820B 4980V00820A 4980V00823B 3809V00356D 3550V00269C 3550V00311C 4810V00815B 4980V00814B 3809V00355D 3550V00310B 3550V00356A 5018V00066A 4810V00819B 4980V00808B 4980V00809A 4810V00818B 3210V00165B 3210V00191A 4810V00713K 6871VMMR92A 6871VPMA55A 6871VSMY73A 6871VSMY72A 6871VSMU24B 6871VSME80A 4814V00434A 4814V00394A 6871VSME87A 3141VSN918B 4980V00886B 4980V00817A 6912B22002C 4814V00396A 4930V00301A 5900V12001B 4810V00813A 5900V06006A 4980V00813B 6871VSMW48A 6316000002C 4810V00659A 6871VSMV96B 6871VSMV95D 6871VSMW00A 6871VSMW47A 3500V00061P 6871VSMV90B 6871VSMW40A Description SPEAKER,WOOFER C080P23K1450 ESTEC WOOFER 8OHM 15/25W 84DB 80 NON SPEAKER,TWEETER D016D01K1450 ESTEC TWEETER(DOME) 8HMOHM 15/25W 85DB POWER CORD,UL/CSA3000MM 3P HUG BLACK VOLEX CSA 3000MM HUG BLACK 500MH 7A CABINET ASSEMBLY,RU-44SZ61D MONO NB03JC FRONT TOTAL BUTTON,CONTROL BRACKET ASSEMBLY,SPEAKER RU-44SZ61D NB03JC GRILLE BLACK COVER,NON DN-44SZ60H EGI PLATE COVER,NON RN044SZ50H EGI PLATE C/A RIGHT SCREEN ASSEMBLY,TOPPAN NON RN-44SZ50H 1000*570*3.15 LCD TYPE SUPPORTER,SCREEN EGI RIGHT, DN-44SZ60D SUPPORTER,SCREEN EGI BOTTOM, DN-44SZ60H SUPPORTER,SCREEN EGI TOP,RN-44SZ50H SUPPORTER,SCREEN EGI LEFT, DN-44SZ60D BACK COVER ASSEMBLY,RU-44SZ51D NON UPPER COVER,NON RU-44SZ61D ABS, AF-303S LAMP FAN COVER,REAR RU-44SZ61D PC-ABS . BRACKET,COVER DN-44SZ51H/60H NB03KB ABS, AF-303S LAMP SIDE DUCT SUPPORTER,ENGINE EGI DN-44SZ60H BACK COVER ASSEMBLY,RU-44SZ61D NON LOWER COVER,NON RU-44SZ61D ABS, AF-303S BACK LOWER COVER,MIDDLE RN-44SZ50H ABS DUST MIRROR,NON SSC(SAMSUNG CORNING) Mirror : RN-44SZ50/60H BACK MIRROR BRACKET,NON MIRROR LEFT,RN-52SZ50H NB03JA PC-ABS . SUPPORTER,MIRROR AL DN-44SZ60D SUPPORTER,MIRROR AL LOWER,RN-44SZ50H BRACKET,NON MIRROR RIGHT,RN-52SZ50 NB03JA PC-ABS . FRAME,ABS AF-303S RN-48SZ40H MAIN CHASSIS FRAME,CHASSIS HIPS 40AF DN-44SZ60D SMPS BRACKET,REAR AV RU-44SZ61D NB03JC ABS, AF-303S . PCB ASSEMBLY,MAIN NB-03JC BOTTOM M/I ASSY FOR N.A. PCB ASSEMBLY,POWER SMPS NB-03JC M/I ASSY FOR N.A. PCB ASSEMBLY,SUB TUNER NB03JC M/I ASSY FOR N.A. PCB ASSEMBLY,SUB DIGITAL NB03JC M/I ASSY FOR N.A. PCB ASSEMBLY,SUB NB03KB COMP M/I PCB ASSEMBLY,SUB CRM MB03CB DRIVE M/I ASSY FOR 720P DLP SHIELD ASSY,DN-52SZ60H NB03KB SUS ,SHIELD CASE DRIVE BOTTOM SHIELD,COVER RN-52SZ50H NB03JA SECC(EGI) DRIVE FRONT DLP 720P PCB ASSEMBLY,SUB AC NB03JC LINE FILTER FOR N.A. CHASSIS ASSEMBLY,SUB NB03JC FOR N.A. SUPPORTER,SMPS SECC(EGI) DLP SUPPORTER,OPTICAL EGI ENGINE DLP,RN-44SZ50H LAMP,HIGH PRESSURE MECURY P-VIP 120/1.3 E23H OSRAM 120V 0.4A 120W 15KV SHIELD,COVER RN-52SZ50H NB03JA SECC(EGI) COVER,LAMP.DLP720P-ENGINE HOLDER,PC+GF30% LAMP FAN,DC G1225S12B2 DONGYANG 120*120*25 12V 1000RPM 9-14V L1000MM BRACKET,FIXER RN-44SZ50H NB03JA ABS, AF-303S FAN HOLDER FAN,DC F6025S12B2 DONGYANG 60*60*25 12V 2000RPM 9-14V L650MM SUPPORTER,FAN SPCC(CR) ,DN-44SZ60H PCB ASSEMBLY,SUB TX NB03KB PRE AMP BALLAST,PT VIP 120AC/380 O1 OSRAM 120W 15KV DN52SZ51H SMK101CCT09301 BRACKET,BALLAST RE-44SZ20 NON ABS NON PCB ASSEMBLY,SUB NB03KB TACT S/W PCB ASSEMBLY,SUB LED MB03CC M/I ASSY FOR CHINA PCB ASSEMBLY,SUB S/W NB03JA CASE SW RN-44SZ50H PCB ASSEMBLY,SUB A/V NB03KB SIDE A/V BOARD ASSY,RU-44SZ61D NB03JC SIDE A/V BLACK PCB ASSEMBLY,SUB INTER NB03KB INTERFACE PCB ASSEMBLY,SUB NB03KB COLOR WHEEL SENSOR

- 25 -

400 410 411

430 401 310 431

305

434 432 433 308 309 700 404 681 680 402

300

650

301

EXPLODED VIEW(52)

- 26 660 503 630 121 530 502 570 601 590 550 572 501 600
621

670

403

120 174

420

304 571

306 540 520

302

560 720

620

612 610 622 623 640 641 611

602

EXPLODED VIEW PARTS LIST

No. 120 121 174 300 301 302 304 305 306 308 309 310 400 401 402 403 404 410 411 420 430 431 432 433 434 501 502 503 520 530 540 550 560 570 571 572 590 600 601 602 610 611 612 620 621 622 623 630 640 641 650 660 670 680 681 700 720 Part No. 6400WESC01A 6400DESA01A 6410VUH004A 3091V00552D 5020V00870B 4811V00049C 3550V00382A 3351V00007A 3550V00387A 4980V00890B 4980V00889B 4980V00888B 3809V00361F 3550V00269D 3550V00322D 3110V00307B 4980V00885B 3809V00362F 3550V00321C 3550V00365C 5018V00067D 4810V00819B 4980V00883A 4980V00884A 4810V00818B 3210V00165A 3210V00191A 4811V00055C 6871VMMR92A 6871VPMA55A 6871VSMY73A 6871VSMY72A 6871VSMU24B 6871VSME80A 4814V00434A 4814V00394A 6871VSME87A 3141VSN918A 4980V00886B 4980V00817A 6912B22002C 4814V00396A 4930V00301A 5900V12001B 4810V00813A 5900V06006A 4980V00813B 6871VSMW48A 6316000002C 4810V00659A 6871VSMV96B 6871VSMV95D 6871VSMW00B 6871VSMW47A 3500V00061P 6871VSMY69A 6871VSMW40A Description SPEAKER,WOOFER C080P23K1450 ESTEC WOOFER 8OHM 15/25W 84DB 80 NON SPEAKER,TWEETER D016D01K1450 ESTEC TWEETER(DOME) 8HMOHM 15/25W 85DB POWER CORD,UL/CSA3000MM 3P HUG BLACK VOLEX CSA 3000MM HUG BLACK 500MH 7A CABINET ASSEMBLY,RU-52SZ61D NON NB03JC FULL BUTTON,CONTROL DN-52SZ60D ABS, HF-380 7KEY . BRACKET ASSEMBLY,SPEAKER DU-52SZ61D NB04AA GRILLE,LG BRAND COVER,FRONT ,DN-52SZ60H SECC(EGI) ,MIDDLE SCREEN ASSEMBLY,SHIINSUNG NON RN-52SZ30H 1178*670*3.6 LCD TYPE COVER,FRONT DN-52SZ60H SPCC(CR) ,C/A RIGHT SUPPORTER,SCREEN SECC(EGI) SIDE(CUSHION),RN-52SZ50H SUPPORTER,SCREEN EGI BOTTOM(CUSHION),RN-52SZ50H SUPPORTER,SCREEN SECC(EGI) TOP BACK COVER ASSEMBLY,RU-52SZ61D NON ZENITH COVER,LAMP RU-44SZ51D PC-ABS FAN 7S00115A COVER,LAMP RU-52SZ51D HIPS 40AF SIDE CASE,NON LAMP DUCT DLP 52SZ60H PC-ABS . SUPPORTER,BACK COVER SECC(EGI) RN-52SZ50H BACK COVER ASSEMBLY,RU-52SZ51D NON ZENITH COVER,LAMP RU-52SZ51D HIPS 40AF ZENITH COVER ASSY,RU-52SZ51D ABS, AF-303S DUST MIRROR,REFLECTION SSC(SAMSUNG CORNING) 0000 1172(H1)*590(H2)*604(V1)*3T . BRACKET,NON MIRROR LEFT,RN-52SZ50H NB03JA PC-ABS . SUPPORTER,MIRROR AL TOP,52SZ50H SUPPORTER,MIRROR AL BOTTOM 52SZ50H BRACKET,NON MIRROR RIGHT,RN-52SZ50 NB03JA PC-ABS . FRAME,HIPS 40AF RN-48SZ40 SMPS CHASSIS FRAME,CHASSIS HIPS 40AF DN-44SZ60D SMPS BRACKET ASSEMBLY,REAR AV RU-52SZ51D NB03JC ZENITH PCB ASSEMBLY,MAIN NB-03JC BOTTOM M/I ASSY FOR N.A. PCB ASSEMBLY,POWER SMPS NB-03JC M/I ASSY FOR N.A. PCB ASSEMBLY,SUB TUNER NB03JC M/I ASSY FOR N.A. PCB ASSEMBLY,SUB DIGITAL NB03JC M/I ASSY FOR N.A. PCB ASSEMBLY,SUB NB03KB COMP M/I PCB ASSEMBLY,SUB CRM MB03CB DRIVE M/I ASSY FOR 720P DLP SHIELD ASSY,DN-52SZ60H NB03KB SUS ,SHIELD CASE DRIVE BOTTOM SHIELD,COVER RN-52SZ50H NB03JA SECC(EGI) DRIVE FRONT DLP 720P PCB ASSEMBLY,SUB AC NB03JC LINE FILTER FOR N.A. CHASSIS ASSEMBLY,SUB NB03JC OPTICS ENGINE ASSY FOR N.A. SUPPORTER,SMPS SECC(EGI) DLP SUPPORTER,OPTICAL EGI ENGINE DLP,RN-44SZ50H LAMP,HIGH PRESSURE MECURY P-VIP 120/1.3 E23H 120V 0.4A 120W DN52SZ51H 15KV SHIELD,COVER RN-52SZ50H NB03JA SECC(EGI) COVER,LAMP.DLP720P-ENGINE HOLDER,PC+GF30% LAMP FAN,DC G1225S12B2 DONGYANG 120*120*25 12V 1000RPM 9-14V L1000MM BRACKET,FIXER RN-44SZ50H NB03JA ABS, AF-303S FAN HOLDER FAN,DC F6025S12B2 DONGYANG 60*60*25 12V 2000RPM 9-14V L650MM SUPPORTER,FAN SPCC(CR) ,DN-44SZ60H PCB ASSEMBLY,SUB TX NB03KB PRE AMP BALLAST,PT VIP 120AC/380 O1 OSRAM 120W 15KV DN52SZ51H SMK101CCT09301 BRACKET,BALLAST RE-44SZ20 NON ABS NON PCB ASSEMBLY,SUB NB03KB TACT S/W PCB ASSEMBLY,SUB LED MB03CC M/I ASSY FOR CHINA PCB ASSEMBLY,SUB S/W NB03KB CASE SW DN-52SZ51H PCB ASSEMBLY,SUB A/V NB03KB SIDE A/V BOARD ASSY,RU-44SZ61D NB03JC SIDE A/V BLACK PCB ASSEMBLY,SUB INTER MB03CC M/I ASSY FOR CHINA PCB ASSEMBLY,SUB NB03KB COLOR WHEEL SENSOR

- 27 -

REPLACEMENT PARTS LIST

For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows; CC, CX, CK, CN : Ceramic CQ : Polyestor CE : Electrolytic RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RF : Fusible

RUN DATE : 2004.1.19

LOCA. NO

PART NO

DESCRIPTION

LOCA. NO IC602 IC603

PART NO 0IFA754207A 0ISS455880A 0IMCRTI011A 0IMMRAL015A 0IMCRFA003A 0IMCRAL006A 0IMMRSS053A 0IPH741400E 0IMCRTI014A 0IMCRSG007A 0IKE702700D 0IMCRSG008A 0IMCRSG008A 0ITI740000Q 0IMCRMX001A 0IMCRSG008A 0IIC271600A 0IMCRMX001A 0IMCRSG010A 0IMCRSG008A 0IMP242560A 0IMCRSJ001A 0IMCRON002A 0IMCRSK002A 0ISK615311B 0ISH817300B 0ISH817300B 0ISS781200H 0IMCRTI012A 0IMCRTI013A 0IMCRSG007A 0IMCRSG008A 0IMCRSG008A 0IMCRSG008B 0IMCRSG007A

DESCRIPTION KA75420ZTA 3P,TO92 TP 4.2V KA4558D 8SOP OP AMP 2503227001(DDP1010) 529P AT49LV8192A90TC 48P 8MBIT KA2903 8SOP R/TP AMPLIFIER AT24C16AN10SI2.7 8P SOIC R/TP EEPROM K4R271669ETCS8 54P 128MBIT 74HC14D 14SOP TP SHITTER TRIGGER CDCR83 24P DIRECT RANBUS CLOCK 74VIT125CTR 5P S0T3235L KIA7027AF 3, SOT89 TP RESET IC 2.7V 74LX1G14CTR 5P SOT3235L 74LX1G14CTR 5P SOT3235L SN74LVC00AD 14SOP R/TP LOGIC DTV MAX708SCSA 8P SOP R/TP RESET 74LX1G14CTR 5P SOT3235L MK2716STR 8P MAX708SCSA 8P SOP R/TP RESET ST3232CDR SOP16 R/TP RS232 74LX1G14CTR 5P SOT3235L 24LC256I/SM 8P SC1565IST1.8 3P SOT223 MC33262P ON SEMI 8P STRF6467 5P T0220(LB) STRG6153T(LF1101) 5PIN BK STR PC817XF3 4D PHOTO COUPLER PC817XF3 4D PHOTO COUPLER KA78R12 4P,TO220F BK LOW DROP 12V 2503252002(DAD1000) 80P SNSH6742CFA0PA(P32J6742PAG) 64P 74VIT125CTR 5P S0T3235L 74LX1G14CTR 5P SOT3235L 74LX1G14CTR 5P SOT3235L 74LX1G07CTR 5P SOT3235L 74VIT125CTR 5P S0T3235L

IC
IC1 IC1 IC1 IC100 IC1000 IC1001 IC1002 IC1004 IC1008 IC101 IC101 IC102 IC1200 IC1202 IC1602 IC2 IC200 IC208 IC301 IC303 IC304 IC305 IC4 IC400 IC401 IC402 IC403 IC404 IC405 IC406 IC407 IC409 IC409 IC410 IC413 IC414 IC5 IC500 IC500 IC501 IC502 IC503 IC600 IC601 IC601 IC601 0IMCRSH003A 0IPRPTO002A 0IZZVC0051J 0IMCRS5003A 0IMI623200B 0IPRPFA006A 0IPRPFA007A 0IMMRNE002A 0IMI623200B 0IPH827150A 0ITK118100B 0IMMRAL014B 0IMCRSO008A 0IMO744053B 0ISH052100C 0IFA754207A 0IMCRAD002A 0ISO206900A 0ICTMLG003C 0ITI740000Q 0IMMRHY033A 0IMMRHY033A 0IMCRAL006A 0ICTMMI038B 0IMCRTI019A 0ISH122100B 0ISH302122A 0ISH052100C 0ISH323422A 0ISH323422A 0ISJ156612A 0IKE780500P 0IKE781200P 0ISH052100C 0IKE780900M 0IMCRFA009A 0IFA754207A 0IPRPTI001A 0ILNRMN005A 0ILNRMN005A 0IZZVF0020A 0IMCRET002B 0IMCRXL003A 0IMCRMN014A 0IFA741230A 0IMCRNS006A GP2S40 SHARP 4P TC7S14F(T5L,T) 5P SCHMITT INVERTER M37272E8A(OTP) DIP 42P BK MICOM SIL169 CL100 100P M62320FP 16P SOP TP I/O EXPANDER RC1117S33T SOT223 R/TP 3.3VOLT RC1117S25T SOT223 R/TP 2.5VOLT UPD64083GF3BA 100 QFP ST 3D YC M62320FP,I/O EXPANDER 16P P82B715T 8SOP R/TP IIC EXTENDER TK11840L 8P SOT23L DCDC CONVERTER AT24C02N10SI2.7 8P SOIC R/TP 2K(256X8) CXA2151Q SONY 48P 60LCD MC74HC4053DW 16SOP 3*2CH.MUX PQ05RD21 4SIP ST REGULATOR KA75420ZTA 3P,TO92 TP 4.2V AD9883AKST110 80P DIGITAL BOARD CXA2069Q QFP64 BK I2C BUS AV S/W LGDT1502M 304P READY2 AMKOR SN74LVC00AD 14SOP R/TP LOGIC DTV HY57V643220C(L)T6 86P 64M HY57V643220C(L)T6 86P 64M AT24C16AN10SI2.7 8P SOIC R/TP EEPROM COPY M306V3FGFP 100P 16BIT TFP410 64P TRANSMITTER PANEL BUS 165MHZ PQ12RD21 4SIP ST REGULATOR PQ30RV21 TO220 PQ05RD21 4SIP ST REGULATOR PQ3RF23 4P(TO220) 3.3V PQ3RF23 4P(TO220) 3.3V SC15661T2.5TR 3P TO2203L KIA78L05BP(AT) 3P 5V,150MA KIA7812API TO220 ST 3P 12V PQ05RD21 4SIP ST REGULATOR KIA7809API TO220 ST 3P 9V KA78M08RTM 2P DPAK KA75420ZTA 3P,TO92 TP 4.2V TFP401PZP 100 DIGITAL RECEIVER VPX3226E 44 VIDEO VPX3226E 44 VIDEO X1272 720PIXEL 251P BK 0.8DIAGONAL EL2250CST7 8P R/TP OP AMP XC95144XL10TQ100C 3.3V 100P MSP3440G QA B8 V3 80 SOUND IC DM74LS123MX 16SOP LM4765T 15P TO220 ST AUDIO

IC700 IC701 IC702 IC705 IC800 IC800 IC801 IC802 IC802 IC803 IC804 IC804 IC805 IC806 IC806 IC807 IC807 IC808 IC808 IC810 IC811 IC820 IC831 IC832 IC841 IC845 IC900 IC901 IC906 IC907 IC908 IC909 IC910

TRANSISTOR
IC903 IC904 IC905 Q100 Q1000 Q1001 Q1001 Q1002 Q1002 Q1003 Q1003 0TFFC80015A 0TFFC80015A 0TFFC80015A 0TR830009BA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA FDS6930A MOSFET 8P SO8 30V 5.5A FDS6930A MOSFET 8P SO8 30V 5.5A FDS6930A MOSFET 8P SO8 30V 5.5A BSS83 CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC

- 28 -

REPLACEMENT PARTS LIST

LOCA. NO Q1004 Q1004 Q1005 Q1005 Q1006 Q1007 Q1008 Q1009 Q101 Q1010 Q1011 Q1012 Q1013 Q1014 Q1015 Q1016 Q1017 Q102 Q103 Q107 Q109 Q1200 Q1201 Q1202 Q1203 Q1204 Q1205 Q1206 Q1207 Q1208 Q1209 Q1210 Q1213 Q1214 Q1215 Q1216 Q1217 Q1218 Q1219 Q2 Q201 Q202 Q203 Q204 Q205 Q206 Q207 Q208 Q209 Q210 Q211 PART NO 0TR387500AA 0TR150400BA 0TR387500AA 0TR150400BA 0TR387500AA 0TR150400BA 0TR150400BA 0TR387500AA 0TR830009BA 0TR150400BA 0TR150400BA 0TR150400BA 0TR150400BA 0TR387500AA 0TR150400BA 0TR387500AA 0TR150400BA 0TRKE80038A 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR150400BA 0TR102009AG 0TR387500AA 0TR387500AA 0TR150400BA 0TR150400BA 0TR387500AA 0TR387500AA 0TR387500AA 0TR150400BA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA DESCRIPTION CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC BSS83 CHIP 2SA1504S(ASY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC KTC3552TRTK SOT23F 50V 3A CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP KRC102S KEC TP SOT23 CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC D1 D100 D101 D2 D3 D300 D403 D404 D431 D432 D433 D434 D435 D436 D437 D438 D439 D5 D6 D601 D603 D605 D606 D607 D801 0DD184009AA 0DD184009AA 0DD184009AA 0DD184009AA 0DD226239AA 0DL233309AC 0DS113379BA 0DD184009AA 0DS113379BA 0DS113379BA 0DS113379BA 0DS113379BA 0DS113379BA 0DS113379BA 0DS113379BA 0DS113379BA 0DS113379BA 0DD184009AA 0DD184009AA 0DD184009AA 0DD184009AA 0DD184009AA 0DD184009AA 0DD184009AA 0DD606000AA LOCA. NO Q500 Q501 Q501 Q502 Q502 Q504 Q601 Q601 Q602 Q602 Q603 Q605 Q605 Q614 Q615 Q616 Q617 Q618 Q801 Q802 Q810 Q841 Q842 Q851 PART NO 0TR150400BA 0TR830009BA 0TR830009BA 0TR830009BA 0TR830009BA 0TR102009AG 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR322709AA 0TR387500AA 0TR150400BA 0TR102008AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TF283700AA 0TR945009AA 0TR322709AA 0TR945009AA DESCRIPTION CHIP 2SA1504S(ASY) KEC BSS83 BSS83 BSS83 BSS83 CHIP KRC102S KEC TP SOT23 CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC KTC3227Y,TP(KTC1627A),KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC KRA102S R/TP KEC SOT23 CHIP TR CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC 2SK2837 500V 20A TO3P KSC945CY TO92 50V 150MA KTC3227Y,TP(KTC1627A),KEC KSC945CY TO92 50V 150MA

DIODE
KDS184S CHIP 85V 300MA KEC TP KDS184S CHIP 85V 300MA KEC TP KDS184S CHIP 85V 300MA KEC TP KDS184S CHIP 85V 300MA KEC TP CHIP KDS226 SOT23 LED,SAM2333 1SS133 T72 DO34 90V KDS184S CHIP 85V 300MA KEC TP 1SS133 T72 DO34 90V 1SS133 T72 DO34 90V 1SS133 T72 DO34 90V 1SS133 T72 DO34 90V 1SS133 T72 DO34 90V 1SS133 T72 DO34 90V 1SS133 T72 DO34 90V 1SS133 T72 DO34 90V 1SS133 T72 DO34 90V KDS184S CHIP 85V 300MA KEC TP KDS184S CHIP 85V 300MA KEC TP KDS184S CHIP 85V 300MA KEC TP KDS184S CHIP 85V 300MA KEC TP KDS184S CHIP 85V 300MA KEC TP KDS184S CHIP 85V 300MA KEC TP KDS184S CHIP 85V 300MA KEC TP RBV606 600V 6A 150A NA 10UA

- 29 -

REPLACEMENT PARTS LIST

LOCA. NO D801 D802 D803 D804 D805 D806 D810 D820 D821 D822 D832 D833 D834 D841 D845 D881 D881 D881 D891 D901 D902 D903 D904 D905 D906 D907 D908 D909 Q810 ZD01 ZD1 ZD10 ZD2 ZD201 ZD202 ZD203 ZD204 ZD3 ZD4 ZD5 ZD6 ZD601 ZD602 ZD602 ZD603 ZD841 ZD851 ZD9 PART NO 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DRSE00038A 0DRSE00038A 0DD100009AM 0DD100009AM 0DD100009AM 0DD100009AM 0DR010009AA 0DD100009AM 0DD260000BB 0DD100009AP 0DD414809ED 0DRSA00170A 0DD120000BB 0DD420000BB 0DD220000AC 0DRON00088A 0DRON00088A 0DRON00088A 0DRON00088A 0DRON00088A 0DSON00028A 0DRON00098A 0DZGS00108A 0DRGS00328A 0DR260001AA 0DR050008AA 0DZ620009BB 0DZ620009BB 0DZ620009BB 0DZ560009CF 0DZ560009CF 0DZ560009CF 0DZ560009CF 0DZ620009BB 0DZ620009BB 0DZ620009BB 0DZ620009BB 0DD414809ED 0DD414809ED 0DR050008AA 0DR050008AA 0DZ620009BB 0DZ620009BB 0DZ620009BB DESCRIPTION SD05.TC SOD323 5V 5A 15A SD05.TC SOD323 5V 5A 15A SD05.TC SOD323 5V 5A 15A SD05.TC SOD323 5V 5A 15A SDC15 TVS SOT23 12.8V SDC15 TVS SOT23 12.8V EU1ZV(1) TP SANKEN EU1ZV(1) TP SANKEN EU1ZV(1) TP SANKEN EU1ZV(1) TP SANKEN EG01C 1000V 0.5A 10A 100NSEC 50UA EU1ZV(1) TP SANKEN BRIDGE D2SBA60(STK) SHINDENKEN EG1ZV(1) TP SANKEN TP SANKEN 1N4148 TP GRANDE FMLG14S TO220 400V 5A 70A FMLG12S D4L20U SHINDENGEN FMLG22S TO220 200V 10A 150A BAT54SWT1 60V 3A 4A .SEC .A BAT54SWT1 60V 3A 4A .SEC .A BAT54SWT1 60V 3A 4A .SEC .A BAT54SWT1 60V 3A 4A .SEC .A BAT54SWT1 60V 3A 4A .SEC .A BAV99RWT1 70V 215MA 500MA .SEC .A MBRD320RL 30V 150MA 200MA .SEC .A ZENERS,SMZJ3793B SS26 GENERAL DO214AC 60V FMG26S TO220 600V 6A 50A SD05.TC SOD323 5V 5A 15A ZENERS,MTZJ6.2B ZENERS,MTZJ6.2B ZENERS,MTZJ6.2B ZENERS,MTZJ5.6B ZENERS,MTZJ5.6B ZENERS,MTZJ5.6B ZENERS,MTZJ5.6B ZENERS,MTZJ6.2B ZENERS,MTZJ6.2B ZENERS,MTZJ6.2B ZENERS,MTZJ6.2B 1N4148 TP GRANDE 1N4148 TP GRANDE SD05.TC SOD323 5V 5A 15A SD05.TC SOD323 5V 5A 15A ZENERS,MTZJ6.2B ZENERS,MTZJ6.2B ZENERS,MTZJ6.2B LOCA. NO C1 C100 C101 C1011 C1013 C1019 C1020 C1023 C103 C1035 C1036 C1039 C1042 C1049 C105 C1055 C106 C1060 C108 C11 C110 C111 C112 C112 C117 C1201 C1202 C1204 C1205 C1206 C1207 C1208 C1209 C1216 C1217 C1218 C1234 C1237 C124 C1250 C1251 C126 C128 C129 C131 C133 C140 C140 C142 C143 C144 PART NO 0CH3104K566 0CE226SF6DC 0CE106VF6DC 0CE476VF6DC 0CE476VF6DC 0CE105VK6DC 0CE476VF6DC 0CE476VF6DC 0CE475VK6DC 0CE106VF6DC 0CE106VF6DC 0CE476VF6DC 0CE106VF6DC 0CE106VF6DC 0CE476SF6DC 0CE106VF6DC 0CE476VK6DC 0CE476SF6DC 0CE106VF6DC 0CE226VF6DC 0CE476VK6DC 0CE476VF6DC 0CE475VK6DC 0CE106SF6DC 0CQ2231N509 0CE106VF6DC 0CE106VF6DC 0CE106VF6DC 0CE106VF6DC 0CE106VF6DC 0CE106VF6DC 0CE106VF6DC 0CE106VF6DC 0CE106VF6DC 0CE106VF6DC 0CE106VF6DC 0CE476VF6DC 0CE105VK6DC 0CQ2231N509 0CE105VK6DC 0CE105VK6DC 0CE226SF6DC 0CE476VK6DC 0CE226SF6DC 0CE476VK6DC 0CE476VH6DC 0CE475VK6DC 0CE226SF6DC 0CE475WJ6DC 0CE475WJ6DC 0CE226SF6DC 0.1UF 50V 10% 22UF MVG 16V M 10UF MV 16V 20% 47UF MV 16V 20% 47UF MV 16V 20% 1UF MV 50V 20% 47UF MV 16V 20% 47UF MV 16V 20% 4.7UF MV 50V 20% 10UF MV 16V 20% 10UF MV 16V 20% 47UF MV 16V 20% 10UF MV 16V 20% 10UF MV 16V 20% 47UF MVG 16V M 10UF MV 16V 20% 47UF MV 50V 20% 47UF MVG 16V M 10UF MV 16V 20% 22UF MV 16V 20% 47UF MV 50V 20% 47UF MV 16V 20% 4.7UF MV 50V 20% 10UF MVG 16V 20% 0.022UF D 100V 10% 10UF MV 16V 20% 10UF MV 16V 20% 10UF MV 16V 20% 10UF MV 16V 20% 10UF MV 16V 20% 10UF MV 16V 20% 10UF MV 16V 20% 10UF MV 16V 20% 10UF MV 16V 20% 10UF MV 16V 20% 10UF MV 16V 20% 47UF MV 16V 20% 1UF MV 50V 20% 0.022UF D 100V 10% 1UF MV 50V 20% 1UF MV 50V 20% 22UF MVG 16V M 47UF MV 50V 20% 22UF MVG 16V M 47UF MV 50V 20% 47UF MV 25V 20% 4.7UF MV 50V 20% 22UF MVG 16V M 4.7UF MVK 35V 20% 4.7UF MVK 35V 20% 22UF MVG 16V M DESCRIPTION

CAPACITOR
C1 0CE476DF618 47UF STD 16V M

- 30 -

REPLACEMENT PARTS LIST

LOCA. NO C146 C149 C15 C152 C16 C1620 C1621 C2 C2 C20 C200 C202 C202 C203 C204 C205 C205 C206 C208 C209 C210 C212 C215 C216 C217 C218 C222 C223 C227 C228 C231 C236 C245 C246 C247 C247 C248 C250 C252 C260 C261 C262 C29 C3 C312 C314 C406 C406 C407 C408 C409 PART NO 0CE106SF6DC 0CE106SF6DC 0CE105VK6DC 0CE106SF6DC 0CE476VF6DC 0CE107VF6DC 0CE107VF6DC 0CN1030F679 0CH3104K566 0CE105VK6DC 0CE226SF6DC 0CK105DF64A 0CE106SF6DC 0CK105DF64A 0CE105VK6DC 0CE105VK6DC 0CE106SF6DC 0CE106SF6DC 0CK105DF64A 0CE105VK6DC 0CK105DF64A 0CE105VK6DC 0CK105DF64A 0CE105VK6DC 0CK105DF64A 0CE105VK6DC 0CE105VK6DC 0CE105VK6DC 0CE226VF6DC 0CK823DK56A 0CE107SF6DC 0CK105DF64A 0CE106SF6DC 0CE226SF6DC 0CE227VF6DC 0CE106SF6DC 0CE226SF6DC 0CE106SF6DC 0CE226SF6DC 0CE475VK6DC 0CE475VK6DC 0CE227VF6DC 0CE105VK6DC 0CE476VF6DC 0CE226SF6DC 0CE226SF6DC 0CE227VF6DC 0CE226SF6DC 0CE107VH6DC 0CE107SF6DC 0CE107SF6DC DESCRIPTION 10UF MVG 16V 20% 10UF MVG 16V 20% 1UF MV 50V 20% 10UF MVG 16V 20% 47UF MV 16V 20% 100UF MV 16V 20% 100UF MV 16V 20% 10000P 16V M Y 0.1UF 50V 10% 1UF MV 50V 20% 22UF MVG 16V M 1UF 2012 16V 20% 10UF MVG 16V 20% 1UF 2012 16V 20% 1UF MV 50V 20% 1UF MV 50V 20% 10UF MVG 16V 20% 10UF MVG 16V 20% 1UF 2012 16V 20% 1UF MV 50V 20% 1UF 2012 16V 20% 1UF MV 50V 20% 1UF 2012 16V 20% 1UF MV 50V 20% 1UF 2012 16V 20% 1UF MV 50V 20% 1UF MV 50V 20% 1UF MV 50V 20% 22UF MV 16V 20% 82000PF 2012 50V 10% 100UF MVG 16V M 1UF 2012 16V 20% 10UF MVG 16V 20% 22UF MVG 16V M 220UF MV 16V 20% 10UF MVG 16V 20% 22UF MVG 16V M 10UF MVG 16V 20% 22UF MVG 16V M 4.7UF MV 50V 20% 4.7UF MV 50V 20% 220UF MV 16V 20% 1UF MV 50V 20% 47UF MV 16V 20% 22UF MVG 16V M 22UF MVG 16V M 220UF MV 16V 20% 22UF MVG 16V M 100UF MV 25V 20% 100UF MVG 16V M 100UF MVG 16V M LOCA. NO C410 C411 C412 C425 C426 C427 C428 C431 C432 C433 C434 C435 C437 C438 C451 C453 C454 C456 C456 C462 C480 C482 C50 C500 C501 C503 C505 C514 C515 C516 C517 C518 C519 C519 C520 C521 C522 C522 C523 C524 C525 C525 C528 C530 C531 C533 C534 C535 C536 C541 C600 PART NO 0CE107SF6DC 0CE107SF6DC 0CE476VF6DC 0CE227DD618 0CE227DD618 0CE227DD618 0CE227DD618 0CE107DH618 0CE107DD618 0CE107DD618 0CE227DD618 0CE227DD618 0CE227DD618 0CE107DH618 0CE107DD618 0CE107DD618 0CE336SC6DC 0CE107VH6DC 0CK105DF64A 0CE227DF618 0CE227DH618 0CE107DF618 0CE227SC6DC 0CE106SF6DC 0CE226SF6DC 0CE106SF6DC 0CE226SF6DC 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CE106SF6DC 0CK104CF56A 0CE226SF6DC 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CE106SF6DC 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CE226SF6DC 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK105DF64A 0CE226SF6DC DESCRIPTION 100UF MVG 16V M 100UF MVG 16V M 47UF MV 16V 20% 220UF STD 10V M 220UF STD 10V M 220UF STD 10V M 220UF STD 10V M 100UF STD 25V M 100UF STD 10V M 100UF STD 10V M 220UF STD 10V M 220UF STD 10V M 220UF STD 10V M 100UF STD 25V M 100UF STD 10V M 100UF STD 10V M 33UF MVG 6.3V M 100UF MV 25V 20% 1UF 2012 16V 20% 220UF STD 16V M 220UF STD 25V M 100UF STD 16V M 220UF MVG 6.3V M 10UF MVG 16V 20% 22UF MVG 16V M 10UF MVG 16V 20% 22UF MVG 16V M 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 10UF MVG 16V 20% 0.1UF 1608 16V 10% 22UF MVG 16V M 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 10UF MVG 16V 20% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 22UF MVG 16V M 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 1UF 2012 16V 20% 22UF MVG 16V M

- 31 -

REPLACEMENT PARTS LIST

LOCA. NO C601 C602 C603 C604 C606 C609 C610 C611 C611 C612 C612 C614 C615 C616 C616 C616 C617 C617 C618 C619 C619 C620 C621 C621 C622 C622 C623 C623 C624 C624 C625 C626 C627 C627 C628 C628 C628 C629 C629 C630 C630 C631 C631 C632 C632 C633 C634 C634 C635 C636 C637 PART NO 0CQ1831N509 0CQ1831N509 0CE106DK618 0CE106DK618 0CE107SF6DC 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CE226DK618 0CK104CF56A 0CE226DK618 0CK104CF56A 0CK104CF56A 0CE107SF6DC 0CK104CF56A 0CE475DK618 0CK104CF56A 181-442Z 0CK104CF56A 0CE335VK6DC 0CK104CF56A 0CK104CF56A 0CE106VF6DC 0CK104CF56A 0CE106VF6DC 0CK104CF56A 0CK104CF56A 0CE108DF618 0CK104CF56A 0CE106DF618 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CE228DK650 0CE106VF6DC 0CK104CF56A 181-442Z 0CK104CF56A 0CE475DK618 0CE106VF6DC 0CK104CF56A 0CE107SF6DC 0CK104CF56A 0CK104CF56A 181-442Z 0CK104CF56A 0CK104CF56A 181-442Z 0CK104CF56A 0CK104CF56A 0CK104CF56A DESCRIPTION 0.018UF D 100V 10% 0.018UF D 100V 10% 10UF STD 50V M 10UF STD 50V M 100UF MVG 16V M 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 22UF STD 50V M 0.1UF 1608 16V 10% 22UF STD 50V M 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 100UF MVG 16V M 0.1UF 1608 16V 10% 4.7UF STD 50V 20% 0.1UF 1608 16V 10% PE,ECQB1H104KF3(TR) 0.1UF 1608 16V 10% 3.3UF MV 50V 20% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 10UF MV 16V 20% 0.1UF 1608 16V 10% 10UF MV 16V 20% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 1000UF STD 16V M 0.1UF 1608 16V 10% 10UF STD 16V M 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 2200UF STD 50V M 10UF MV 16V 20% 0.1UF 1608 16V 10% PE,ECQB1H104KF3(TR) 0.1UF 1608 16V 10% 4.7UF STD 50V 20% 10UF MV 16V 20% 0.1UF 1608 16V 10% 100UF MVG 16V M 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% PE,ECQB1H104KF3(TR) 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% PE,ECQB1H104KF3(TR) 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% LOCA. NO C638 C639 C640 C641 C642 C643 C643 C643 C644 C644 C645 C645 C646 C646 C647 C647 C648 C648 C649 C650 C651 C652 C653 C654 C655 C664 C668 C669 C700 C701 C702 C704 C706 C707 C710 C711 C712 C713 C714 C717 C718 C719 C720 C721 C722 C723 C724 C725 C726 C727 C728 PART NO 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CE476VF6DC 0CK104CF56A 0CE226DK618 0CK104CF56A 181-442Z 0CK104CF56A 181-442Z 0CK104CF56A 0CE108DK61A 0CK104CF56A 0CE108DK61A 0CE335VK6DC 0CK104CF56A 0CK104CF56A 0CC270CK41A 0CC270CK41A 0CC270CK41A 0CC270CK41A 0CK104CF56A 0CK104CF56A 0CE335VK6DC 0CE105VK6DC 0CE105VK6DC 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A DESCRIPTION 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 47UF MV 16V 20% 0.1UF 1608 16V 10% 22UF STD 50V M 0.1UF 1608 16V 10% PE,ECQB1H104KF3(TR) 0.1UF 1608 16V 10% PE,ECQB1H104KF3(TR) 0.1UF 1608 16V 10% 1000UF STD 50V M 0.1UF 1608 16V 10% 1000UF STD 50V M 3.3UF MV 50V 20% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 27PF 1608 50V 5% 27PF 1608 50V 5% 27PF 1608 50V 5% 27PF 1608 50V 5% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 3.3UF MV 50V 20% 1UF MV 50V 20% 1UF MV 50V 20% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10%

- 32 -

REPLACEMENT PARTS LIST

LOCA. NO C729 C730 C731 C732 C733 C734 C735 C736 C737 C738 C739 C740 C741 C742 C743 C744 C745 C746 C747 C748 C749 C750 C751 C752 C753 C754 C755 C756 C757 C758 C759 C760 C761 C762 C763 C764 C765 C766 C767 C768 C769 C770 C771 C772 C773 C774 C775 C776 C777 C778 C779 PART NO 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A DESCRIPTION 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% LOCA. NO C780 C781 C782 C783 C800 C800 C801 C801 C801 C802 C802 C803 C804 C804 C805 C805 C806 C806 C806 C807 C807 C807 C808 C808 C809 C809 C810 C811 C812 C813 C814 C814 C814 C815 C816 C817 C818 C818 C818 C819 C820 C820 C821 C821 C822 C822 C823 C823 C824 C824 C825 PART NO 0CK104CF56A 0CC270CK41A 0CC270CK41A 0CK104CF56A 0CK104CF56A 0CE106SF6DC 0CQZVBK002B 0CK104CF56A 0CK105DF64A 0CQZVBK002C 0CK104CF56A 0CK104CF56A 0CF1050W470 0CE106SF6DC 0CK10202510 0CK104CF56A 0CK10202510 0CK104CF56A 0CE226SF6DC 0CK104CF56A 0CK1020K515 0CE336SC6DC 0CQ1021N519 0CC680CK41A 0CC680CK41A 181-007J 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CC680CK41A 0CC680CK41A 0CE107BK618 0CE106SF6DC 0CK104CF56A 0CC100CK11A 0CK104CF56A 0CK104CF56A 181-091R 0CE226SF6DC 0CC680CK41A 181-001K 0CK104CF56A 181-014Y 0CK104CF56A 0CK104CF56A 0CK1020K515 0CK104CF56A 0CK1020K515 0CK104CF56A 0CE107BK618 0CK104CF56A DESCRIPTION 0.1UF 1608 16V 10% 27PF 1608 50V 5% 27PF 1608 50V 5% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 10UF MVG 16V 20% A.C 275V 0.15UF K (S=22.5) 0.1UF 1608 16V 10% 1UF 2012 16V 20% A.C 275V 0.22UF K (S=22.5) 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 1UF 0 500V 5% 10UF MVG 16V 20% 1000P 2KV K B S 0.1UF 1608 16V 10% 1000P 2KV K B S 0.1UF 1608 16V 10% 22UF MVG 16V M 0.1UF 1608 16V 10% 1000P 50V K

33UF MVG 6.3V M 0.001U 100V K 68PF 1608 50V 5% 68PF 1608 50V 5% MPE ECQV1H564JL3(TR), 50V 0.56UF J 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 68PF 1608 50V 5% 68PF 1608 50V 5% 100UF KME 50V M 10UF MVG 16V 20% 0.1UF 1608 16V 10% 10PF 1608 50V 0.5 PF 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% R 1000PF 1KV 10%,10% 22UF MVG 16V M 68PF 1608 50V 5% CE 450V 220UF M LUG(105) 0.1UF 1608 16V 10% MPP 1.6KV 0.0015UF J 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 1000P 50V K

0.1UF 1608 16V 10% 1000P 50V K

0.1UF 1608 16V 10% 100UF KME 50V M 0.1UF 1608 16V 10%

- 33 -

REPLACEMENT PARTS LIST

LOCA. NO C825 C826 C828 C829 C831 C832 C832 C833 C833 C834 C835 C835 C836 C836 C837 C837 C838 C839 C840 C841 C841 C842 C843 C843 C844 C845 C845 C846 C847 C853 C855 C856 C858 C859 C862 C865 C873 C876 C881 C883 C884 C886 C891 C893 C894 C901 C902 C904 C905 C906 C908 PART NO 0CE107BK618 0CK104CF56A 0CC471CK41A 181-120L 181-035N 0CK104CF56A 0CQ1021N509 0CK104CF56A 0CE107BH618 0CK104CF56A 181-010K 0CK104CF56A 0CE476EU61A 0CK104CF56A 0CK104CF56A 0CK1040K945 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CE108BF618 0CK104CF56A 0CK104CF56A 0CK1040K945 0CK104CF56A 0CK104CF56A 0CE107BF618 0CK104CF56A 0CK104CF56A 0CE108BF618 0CE228BF618 0CK1040K945 0CE477DF618 181-091Q 0CE228BF618 181-091Q 0CE108BK61A 0CE227DK618 0CE227BH618 0CE227BH618 181-091Q 181-091Q 0CE338EF618 0CE108BF618 181-091Q 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A DESCRIPTION 100UF KME 50V M 0.1UF 1608 16V 10% 470PF 1608 50V 5% 3300PF 4KV M E DE1010B471KACT4KKD 470 PF 250V 10% 0.1UF 1608 16V 10% 0.001UF D 100V 10% 0.1UF 1608 16V 10% 100UF KME 25V M 0.1UF 1608 16V 10% PP 0.01UF 630V 5% 0.1UF 1608 16V 10% 47UF KMG 400V M 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 50V Z F TR 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 1000UF KME 16V M 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 50V Z F TR 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 100UF KME 16V M 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 1000UF KME 16V M 2200UF KME 16V M 0.1UF 50V Z F TR 470UF STD 16V 20% R 470PF 1KV 10%,10% 2200UF KME 16V M R 470PF 1KV 10%,10% 1000UF KME 50V M 220UF STD 50V M 220UF KME 25V M 220UF KME 25V M R 470PF 1KV 10%,10% R 470PF 1KV 10%,10% 3300UF KMG,RD 16V 20% 1000UF KME 16V M R 470PF 1KV 10%,10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% L1 L1011 L851 JA1201 JA1202 JA201 JA202 JA204 P101B P102B P103B P401A P401B P403 P501 6613V00013G 6612VJH006C 6613V00010B 6613V00013B 380-404A 6612VMH003A 6612VMH003A 6612VMH003A 6612VMH003A 6612VMH003A 6612BBBHN6A 6612BBBHN7A LOCA. NO C909 C910 C911 C912 C913 C919 C920 C921 C922 C924 C926 C927 C929 C930 C931 C932 C933 C934 C936 C937 C938 C939 C940 C941 C942 C943 C944 C945 C946 C947 C949 C950 PART NO 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CS226GJ6DC 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CC471CK41A 0CK271CK46A 0CK272CK46A 0CK104CF56A 0CK104CF56A 0CC101CK41A 0CK121CK46A 0CK103CK56A 0CK104CF56A 0CK103CK56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A 0CK104CF56A DESCRIPTION 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 22UF 7343 35V 20% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 470PF 1608 50V 5% 270PF 1608 50V 5% 2700PF 1608 50V 5% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 100PF 1608 50V 5% 120PF 1608 50V 5% 0.01UF 1608 50V 10% 0.1UF 1608 16V 10% 0.01UF 1608 50V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10% 0.1UF 1608 16V 10%

JACK
JACK ASSEMBLY,PMJ021G 9P JACK,RCA PJ6061E 6P JACK ASSY,PMJ016B 3P JACK ASSY,PMJ021B 9P JACK,DIN PHSJ9504 HOSIDEN . JACK,SCART 365100032 JACK,SCART 365100032 JACK,SCART 365100032 JACK,SCART 365100032 JACK,SCART 365100032 JACK,DIN 4400621 JACK,DIN 743203004

COIL & TRANSFORMER

0LA0102K119 0LA0561K119 150-C02F INDUCTOR,10UH K INDUCTOR,5.6UH K COIL,CHOKE 82UH

- 34 -

REPLACEMENT PARTS LIST

LOCA. NO L861 L871 L891 L903 L904 T801 T810 T830 PART NO 150-C02F 150-C02F 150-C02F 6140VR0007A 6140VR0007A 6170VMCA03F 6170VMCA37B 6170VS0001B DESCRIPTION COIL,CHOKE 82UH COIL,CHOKE 82UH COIL,CHOKE 82UH COIL,DT1608C223 COILCRAFT 22UF+20% COIL,DT1608C223 COILCRAFT 22UF+20% TRANSFORMER,SMPS[COIL] EER4942 1200UH TRANSFORMER,SMPS[COIL] PQ3535 310UH TRANSFORMER,STANDBY EE1927 2200UH LOCA. NO R808 R809 R810 R811 R812 R813 R814 R815 R816 R817 R818 R819 R820 R821 R822 R823 R824 R825 R826 R827 R828 R829 R830 R831 R832 R833 R834 R835 R840 R841 R842 R843 R844 R845 R846 R851 R852 R853 R854 R855 R871 PART NO 0RS8201K607 0RD0152F609 0RD0332H609 180-A01B 0RN3903F409 0RN3903F409 0RN3903F409 0RD1203F609 0RD2202F609 0RD1202F609 0RD2200F609 0RN1002F409 0RD1001F609 180-A01H 0RD1001F609 0RD2701F609 0RD0332H609 0RD4701F609 0RS2202K607 0RS1202K607 0RD3603F609 0RKZVTA001B 0RKZVTA001B 0RS1203K607 0RD0302A609 0RS0161K607 0RS1203K607 0RF0221H609 0RD1601F609 0RD1501F609 0RD3001F609 0RN1801F409 0RD3601F609 0RD3901F609 0RD3902F609 0RN1801F409 0RN2201F409 0RN2201F409 0RN3901F409 0RD1601F609 0RD1002H609 DESCRIPTION 8.2K OHM 2 W 5.00% 15 OHM 1/6 W 5.00% 33 OHM 1/2 W 5.00% RW ROUND G 2W 0.11 K 390K 1/6W 1% 390K 1/6W 1% 390K 1/6W 1% 120K OHM 1/6 W 5.00% 22K OHM 1/6 W 5% 12K OHM 1/6 W 5% 220 OHM 1/6 W 5.00% 10K OHM 1/6 W 1.00% 1K OHM 1/6 W 5% 2 W RW ROUND G 0.27 J 1K OHM 1/6 W 5% 2.7K OHM 1/6 W 5% 33 OHM 1/2 W 5.00% 4.7K OHM 1/6 W 5% 22K OHM 2 W 5.00% 12K OHM 2 W 5.00% 360K 1/6W 5 4.7M OHM 1/2 W 5% 4.7M OHM 1/2 W 5% 120K OHM 2 W 5.00% 30 OHM 1/2 W(7.0) 5.00% 1.6 OHM 2 W 5.00% 120K OHM 2 W 5.00% 2.2 OHM 1/2 W 5.00% 1.6K OHM 1/6 W 5.00% 1.5K OHM 1/6 W 5% 3K OHM 1/6 W 5.00% 1.8K OHM 1/6 W 1.00% 3.6K OHM 1/6 W 5.00% 3.9K OHM 1/6 W 5% 39K OHM 1/6 W 5.00% 1.8K OHM 1/6 W 1.00% 2.2K OHM 1/6 W 1.00% 2.2K OHM 1/6 W 1.00% 3.9K OHM 1/6 W 1.00% 1.6K OHM 1/6 W 5.00% 10K OHM 1/2 W 5.00%

CONNECTOR
JA1200 P100 P101A P102A P103A P201A P202A P800 6630VGA001B 6630GZ00724 6932V25004A 6932V25004A 6932V25004A 6932V25004A 6932V25004A 6630VGA004A CONNECTOR,DSUB 15PIN 2.29MM CONNECTOR,DSUB 24P 1.91MM CONNECTOR,HOUSING 365120098 CONNECTOR,HOUSING 365120098 CONNECTOR,HOUSING 365120098 CONNECTOR,HOUSING 365120098 CONNECTOR,HOUSING 365120098 CONNECTOR,DSUB 9PIN 2.77MM

RESISTOR
AR106 AR301 AR302 AR303 AR304 AR305 AR306 R1 R1253 R2 R3 R4 R5 R556 R557 R558 R559 R56 R560 R561 R632 R634 R666 R667 R668 R673 R803 R805 R806 R807 R808 0RRZVTA001A 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RD0752F609 0RN1002F409 0RD4703F609 0RD4703F609 0RD0752F609 0RD0752F609 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RD0472F609 0RRZVTA001D 0RRZVTA001D 0RF0471H609 0RF0471H609 180-777H 0RD1001H609 180-777H 0RD1001H609 0RN3903G409 0RN3303G409 0RN3903G409 0RN3903G409 0RS1202K607 MNR14E0AJ101 R OHM 100 OHM 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 75 OHM 1/6 W 5.00% 10K OHM 1/6 W 1.00% 470K OHM 1/6 W 5.00% 470K OHM 1/6 W 5.00% 75 OHM 1/6 W 5.00% 75 OHM 1/6 W 5.00% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 47 OHM 1/6 W 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 4.7 OHM 1/2 W 5.00% 4.7 OHM 1/2 W 5.00% RWR 7W 910 J VERT 1K OHM 1/2 W 5.00% RWR 7W 910 J VERT 1K OHM 1/2 W 5.00% 390K OHM 1/4 W 1% 330K OHM 1/4 W 1.00% 390K OHM 1/4 W 1% 390K OHM 1/4 W 1% 12K OHM 2 W 5.00%

SWITCH
SW01 SW01 SW02 SW03 SW04 SW05 SW06 SW07 140-313B 140-275E 140-313B 140-313B 140-313B 140-313B 140-313B 140-313B SWITCH,TACT 2LEAD 160G(TA) SWITCH,PUSH SPBS222EP011 SWITCH,TACT 2LEAD 160G(TA) SWITCH,TACT 2LEAD 160G(TA) SWITCH,TACT 2LEAD 160G(TA) SWITCH,TACT 2LEAD 160G(TA) SWITCH,TACT 2LEAD 160G(TA) SWITCH,TACT 2LEAD 160G(TA)

- 35 -

REPLACEMENT PARTS LIST

LOCA. NO SW701 PART NO 6600DU2093H DESCRIPTION SWITCH,DIP 23902332 LOCA. NO T5 T501 T502 T504 T509 T511 T512 T513 T514 T515 T6 T601 T602 T605 T606 T7 T9 X1 X1001 X1200 X401 X500 X501 X601 PART NO 6200VJT001B 6200QJ3001A 6200QJ3001A 6200QJ3001A 6200QJ3001A 6200QJ3001A 6200VJT006A 6200VJT006A 6200VJT006A 6200VJT006A 6200VJT001B 6200QJ3001A 6200QJ3001A 6200QJ3001A 6200QJ3001A 6200VJT001B 6200VJT001B 156-A01P 156-A02Z 156-A01E 6212AB2015D 6202VDT002E 6202VDT002E 156-A02R DESCRIPTION FILTER,EMC BMK800 50VOLT 1A REEL FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC STC222D 50VOLT 4A 2200PF FILTER,EMC STC222D 50VOLT 4A 2200PF FILTER,EMC STC222D 50VOLT 4A 2200PF FILTER,EMC STC222D 50VOLT 4A 2200PF FILTER,EMC BMK800 50VOLT 1A REEL FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMK800 50VOLT 1A REEL FILTER,EMC BMK800 50VOLT 1A REEL RESONATOR,CRYSTAL HC49U 8.000MHZ RESONATOR,CRYSTAL HC49/U 20.000MHZ RESONATOR,CRYSTAL HC49U 4.000MHZ RESONATOR,CRYSTAL HC49/SM 16MHZ RESONATOR,CRYSTAL SX1SMD 20250000HZ RESONATOR,CRYSTAL SX1SMD 20250000HZ RESONATOR,CRYSTAL HC49U 18.432MHZ

FILTER & CRYSTAL

FB819 FB823 FB861 FB871 FB872 FB881 FB891 IC502 L1005 L1006 L1007 L1013 L801 L802 L804 T1001 T1002 T1004 T1013 T200 T3 T400 T400 T401 T401 T402 T402 T403 T403 T404 T409 T410 T411 T412 T413 T418 T419 T420 T421 T424 T425 T430 T431 T432 T434 T447 T448 T460 125-123A 125-022K 125-123A 125-022K 125-022K 125-022K 125-022K 6200C000009 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6200JB8012T 6200JB8012T 150-F06T 6200C000009 6200C000009 6200C000010 6200C000010 0IZZVF0022C 6200VJT001B 6200QJ3001A 6200VJT006A 6200QJ3001A 6200VJT006A 6200QJ3001A 6200VJT006A 6200QJ3001A 6200VJT006A 6200QJ3001A 6200QJ3001A 6200QJ3001A 6200QJ3001A 6200QJ3001A 6200QJ3001A 6200VJT006A 6200VJT006A 6200VJT006A 6200QJ3001A 6200QJ3001A 6200QJ3001A 6200QJ3001A 6200QJ3001A 6200QJ3001A 6200QJ3001A 6200QJ3001A 6200QJ3001A 6200QJ3001A FILTER,EMC FERRITE BFD3565R2F FILTER,EMC 62MM 1UH FILTER,EMC FERRITE BFD3565R2F FILTER,EMC 62MM 1UH FILTER,EMC 62MM 1UH FILTER,EMC 62MM 1UH FILTER,EMC 62MM 1UH FILTER,B.P. H354LAIK5225 FILTER,EMC HH1M3216501 FILTER,EMC HH1M3216501 FILTER,EMC HH1M3216501 FILTER,EMC HH1M3216501 FILTER,EMC SQE2828 17.2MH FILTER,EMC SQE2828 17.2MH FILTER,EMC SQE3535 20MH FILTER,B.P. H354LAIK5225 FILTER,B.P. H354LAIK5225 FILTER,B.P. H354LAIK5202 FILTER,B.P. H354LAIK5202 FILTER,B.P. AFM730F6M00X3(AF9397A) FILTER,EMC BMK800 50VOLT 1A REEL FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC STC222D 50VOLT 4A 2200PF FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC STC222D 50VOLT 4A 2200PF FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC STC222D 50VOLT 4A 2200PF FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC STC222D 50VOLT 4A 2200PF FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC STC222D 50VOLT 4A 2200PF FILTER,EMC STC222D 50VOLT 4A 2200PF FILTER,EMC STC222D 50VOLT 4A 2200PF FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA FILTER,EMC BMS400 NIGATA 25V 200MA

MISCELLANEOUS
F401 F800 IC704 NTC801 NTC802 PA1 RL831 TU101 TU102 VA800 X800 0FS5000B84B 0FS5001B51D 6204B47985C 163-048D 163-048D 6712SCA228A 141-018E 6700VNF019A 6700VNF019C 164-003K 6204B60001B FUSE,SLOW BLOW 500MA 250V FUSE,SLOW BLOW 5000MA 250V OSCILLATOR,SCO103 100MHZ THERMISTOR,NTC KL15L2R5 +/ 15% 125V THERMISTOR,NTC KL15L2R5 +/ 15% 125V REMOTE CONTROLLER RECEIVER,38KHZ RELAY,DG12D10(M)2 TUNER,TAFCH001F TUNER,TAFCH101P VARISTOR,SVC621D14A 620V 0% OSCILLATOR,VCXO 27MHZ

ACCESSORIES
A1 A2 3828VA0220Y 6710V00102J MANUAL,OWNERS NB03JC REMOTE CONTROLLER

- 36 -

P/NO : 3828VD0148T

Jan., 2004 Printed in Korea

PRINTED CIRCUIT BOARD

MAIN(TOP) MAIN(BOTTOM)

TUNER(TOP)

COMPONENT(TOP)

DIGITAL(TOP)

COMPONENT(BOTTOM) TUNER(BOTTOM)

DIGITAL(BOTTOM)

POWER(SMPS)

SUB EPOXY

DRIVER(TOP)

CONTROL(TOP)

SIDE A/V

CONTROL(BOTTOM)

LED(TOP)

PRE-AMP

DRIVER(BOTTOM)

LED(BOTTOM)

LINE FILTER

CASE SW

INTERFACE