Tips

TIPS

Effects
ABO UT

Search Control Tutorials

BASIC S INDEX NEXT

INTR O DUC TIO N SYSTEM MO DELING ANALYSIS

C R UISE C O NTR O L

MO TO R SPEED

Introduction: PID Controller Design

In this tutorial we will introduce a simple yet versatile feedback compensator structure, the Proportional-Integral-Derivative (PID) controller. We will discuss the

CONTROL PID R O O T LO C US FR EQ UENC Y STATE-SPAC E DIGITAL

effect of each of the pid parameters on the closed-loop dynamics and demonstrate how to use a PID controller to improve the system performance. Key MATLAB commands used in this tutorial are: t f, s t e p, p i d, f e e d b a c k, p i d t o o l, p i d t u n e

Contents
PID Overview The Characteristics of P, I, and D Controllers

SIMULINK MO DELING C O NTR O L

Example Problem Open-Loop Step Response Proportional Control Proportional-Derivative Control Proportional-Integral Control Proportional-Integral-Derivative Control General Tips for Designing a PID Controller Automatic PID Tuning

PID Overview
In this tutorial, we will consider the following unity feedback system:

The output of a PID controller, equal to the control input to the plant, in the time-

domain is as follows: (1)

First, let's take a look at how the PID controller works in a closed-loop system using the schematic shown above. The variable ( ) represents the tracking error, the difference between the desired input value ( ) and the actual output ( ). This error signal ( ) will be sent to the PID controller, and the controller computes both the derivative and the integral of this error signal. The control signal ( ) to the plant is equal to the proportional gain ( integral gain ( ) times the magnitude of the error plus the ) times

) times the integral of the error plus the derivative gain (

the derivative of the error. This control signal ( ) is sent to the plant, and the new output ( ) is obtained. The new output ( ) is then fed back and compared to the reference to find the new error signal ( ). The controller takes this new error signal and computes its derivative and its integral again, ad infinitum. The transfer function of a PID controller is found by taking the Laplace transform of Eq.(1). (2)

= Proportional gain

= Integral gain

= Derivative gain

We can define a PID controller in MATLAB using the transfer function directly, for example:

K p=1 ; K i=1 ; K d=1 ;

s=t f ( ' s ' ) ; C=K p+K i / s+K d * s

C=

s ^ 2+s+1 s

C o n t i n u o u s t i m et r a n s f e rf u n c t i o n .

Alternatively, we may use MATLAB's pid controller object to generate an equivalent continuous-time controller as follows:

C=p i d ( K p , K i , K d )

C=

1 K p+K i*-+K d*s s

w i t hK p=1 ,K i=1 ,K d=1

C o n t i n u o u s t i m eP I Dc o n t r o l l e ri np a r a l l e lf o r m .

Let's convert the pid object to a transfer function to see that it yields the same result as above:

t f ( C )

a n s=

s ^ 2+s+1 s

C o n t i n u o u s t i m et r a n s f e rf u n c t i o n .

The Characteristics of P, I, and D Controllers

A proportional controller ( ) will have the effect of reducing the rise time and will ) will have

reduce but never eliminate the steady-state error. An integral control (

the effect of eliminating the steady-state error for a constant or step input, but it may make the transient response slower. A derivative control ( ) will have the effect of

increasing the stability of the system, reducing the overshoot, and improving the transient response.

The effects of each of controller parameters, system are summarized in the table below. CL RESPONSE Kp Ki Kd

, and

on a closed-loop

RISE TIME

OVERSHOOT

SETTLING TIME Small Change Increase Decrease

S-S ERROR Decrease Eliminate No Change , , and

Decrease Decrease Small Change

Increase Increase Decrease

Note that these correlations may not be exactly accurate, because

are dependent on each other. In fact, changing one of these variables can change the effect of the other two. For this reason, the table should only be used as a reference when you are determining the values for , and .

Example Problem
Suppose we have a simple mass, spring, and damper problem.

The modeling equation of this system is (3) Taking the Laplace transform of the modeling equation, we get (4) The transfer function between the displacement becomes (5) and the input then

Let

M=1k g b=1 0Ns / m k=2 0N / m F=1N Plug these values into the above transfer function (6)

The goal of this problem is to show you how each of obtain F a s tr i s et i m e M i n i m u mo v e r s h o o t N os t e a d y s t a t ee r r o r

and

contributes to

Open-Loop Step Response

Let's first view the open-loop step response. Create a new m-file and run the following code:

s=t f ( ' s ' ) ; P=1 / ( s ^ 2+1 0 * s+2 0 ) ; s t e p ( P )

The DC gain of the plant transfer function is 1/20, so 0.05 is the final value of the

output to an unit step input. This corresponds to the steady-state error of 0.95, quite large indeed. Furthermore, the rise time is about one second, and the settling time is about 1.5 seconds. Let's design a controller that will reduce the rise time, reduce the settling time, and eliminate the steady-state error.

Proportional Control
From the table shown above, we see that the proportional controller (Kp) reduces the rise time, increases the overshoot, and reduces the steady-state error. The closed-loop transfer function of the above system with a proportional controller is: (7)

Let the proportional gain (

) equal 300 and change the m-file to the following:

K p=3 0 0 ; C=p i d ( K p ) T=f e e d b a c k ( C * P , 1 )

t=0 : 0 . 0 1 : 2 ; s t e p ( T , t )

C=

K p=3 0 0

P o n l yc o n t r o l l e r .

T=

3 0 0 s ^ 2+1 0s+3 2 0

C o n t i n u o u s t i m et r a n s f e rf u n c t i o n .

The above plot shows that the proportional controller reduced both the rise time and the steady-state error, increased the overshoot, and decreased the settling time by small amount.

Proportional-Derivative Control
Now, let's take a look at a PD control. From the table shown above, we see that the derivative controller (Kd) reduces both the overshoot and the settling time. The closed-loop transfer function of the given system with a PD controller is: (8)

Let

equal 300 as before and let

equal 10. Enter the following commands

into an m-file and run it in the MATLAB command window.

K p=3 0 0 ; K d=1 0 ; C=p i d ( K p , 0 , K d ) T=f e e d b a c k ( C * P , 1 )

t=0 : 0 . 0 1 : 2 ; s t e p ( T , t )

C=

K p+K d*s

w i t hK p=3 0 0 ,K d=1 0

C o n t i n u o u s t i m eP Dc o n t r o l l e ri np a r a l l e lf o r m .

T=

1 0s+3 0 0 s ^ 2+2 0s+3 2 0

C o n t i n u o u s t i m et r a n s f e rf u n c t i o n .

This plot shows that the derivative controller reduced both the overshoot and the settling time, and had a small effect on the rise time and the steady-state error.

Proportional-Integral Control
Before going into a PID control, let's take a look at a PI control. From the table, we see that an integral controller (Ki) decreases the rise time, increases both the overshoot and the settling time, and eliminates the steady-state error. For the given system, the closed-loop transfer function with a PI control is:

(9)

Let's reduce the

to 30, and let

equal 70. Create an new m-file and enter the

following commands.

K p=3 0 ; K i=7 0 ; C=p i d ( K p , K i ) T=f e e d b a c k ( C * P , 1 )

t=0 : 0 . 0 1 : 2 ; s t e p ( T , t )

C=

1 K p+K i*s

w i t hK p=3 0 ,K i=7 0

C o n t i n u o u s t i m eP Ic o n t r o l l e ri np a r a l l e lf o r m .

T=

3 0s+7 0 s ^ 3+1 0s ^ 2+5 0s+7 0

C o n t i n u o u s t i m et r a n s f e rf u n c t i o n .

Run this m-file in the MATLAB command window, and you should get the following plot. We have reduced the proportional gain (Kp) because the integral controller also reduces the rise time and increases the overshoot as the proportional controller does (double effect). The above response shows that the integral controller eliminated the steady-state error.

Proportional-Integral-Derivative Control
Now, let's take a look at a PID controller. The closed-loop transfer function of the given system with a PID controller is: (10)

After several trial and error runs, the gains

= 350,

= 300, and

= 50

provided the desired response. To confirm, enter the following commands to an mfile and run it in the command window. You should get the following step response.

K p=3 5 0 ; K i=3 0 0 ; K d=5 0 ; C=p i d ( K p , K i , K d ) T=f e e d b a c k ( C * P , 1 ) ;

t=0 : 0 . 0 1 : 2 ; s t e p ( T , t )

C=

1 K p+K i*-+K d*s s

w i t hK p=3 5 0 ,K i=3 0 0 ,K d=5 0

C o n t i n u o u s t i m eP I Dc o n t r o l l e ri np a r a l l e lf o r m .

Now, we have obtained a closed-loop system with no overshoot, fast rise time, and no steady-state error.

General Tips for Designing a PID Controller

When you are designing a PID controller for a given system, follow the steps shown below to obtain a desired response. 1. Obtain an open-loop response and determine what needs to be improved 2. Add a proportional control to improve the rise time 3. Add a derivative control to improve the overshoot 4. Add an integral control to eliminate the steady-state error 5. Adjust each of Kp, Ki, and Kd until you obtain a desired overall response. You can always refer to the table shown in this "PID Tutorial" page to find out which controller controls what characteristics.

Lastly, please keep in mind that you do not need to implement all three controllers (proportional, derivative, and integral) into a single system, if not necessary. For example, if a PI controller gives a good enough response (like the above example), then you don't need to implement a derivative controller on the system. Keep the

controller as simple as possible.

Automatic PID Tuning

MATLAB provides tools for automatically choosing optimal PID gains which makes the trial and error process described above unnecessary. You can access the tuning algorithm directly using pidtune or through a nice graphical user interface (GUI) using pidtool. The MATLAB automated tuning algorithm chooses PID gains to balance performance (response time, bandwidth) and robustness (stability margins). By default the algorthm designs for a 60 degree phase margin. Let's explore these automated tools by first generating a proportional controller for the mass-spring-damper system by entering the following commands:

p i d t o o l ( P , ' p ' )

The pidtool GUI window, like that shown below, should appear.

Notice that the step response shown is slower than the proportional controller we

designed by hand. Now click on the Show Parameters button on the top right. As expected the proportional gain constant, Kp, is lower than the one we used, Kp = 94.85 < 300. We can now interactively tune the controller parameters and immediately see the resulting response int he GUI window. Try dragging the resposne time slider to the right to 0.14s, as shown in the figure below. The response does indeeed speed up, and we can see Kp is now closer to the manual value. We can also see all the other performance and robustness parameters for the system. Note that the phase margin is 60 degrees, the default for pidtool and generally a good balance of robustness and performance.

Now let's try designing a PID controller for our system. By specifying the previously designed or (baseline) controller, C, as the second parameter, pidtool will design another PID controller (instead of P or PI) and will compare the response of the system with the automated controller with that of the baseline.

p i d t o o l ( P , C )

We see in the output window that the automated controller responds slower and exhibits more overshoot than the baseline. Now choose the Design Mode: Extended option at the top, which reveals more tuning parameters.

Now type in Bandwidth: 32 rad/s and Phase Margin: 90 deg to generate a controller similar in performance to the baseline. Keep in mind that a higher bandwidth (0 dB crossover of the open-loop) results in a faster rise time, and a higher phase margin reduces the overshoot and improves the system stability. Finally we note that we can generate the same controller using the command line tool pidtune instead of the pidtool GUI

o p t s=p i d t u n e O p t i o n s ( ' C r o s s o v e r F r e q u e n c y ' , 3 2 , ' P h a s e M a r g i n ' , 9 0 ) ; [ C ,i n f o ]=p i d t u n e ( P ,' p i d ' ,o p t s )

C=

1 K p+K i*-+K d*s s

w i t hK p=3 2 0 ,K i=1 6 9 ,K d=3 1 . 5

C o n t i n u o u s t i m eP I Dc o n t r o l l e ri np a r a l l e lf o r m .

i n f o= S t a b l e :1 C r o s s o v e r F r e q u e n c y :3 2 P h a s e M a r g i n :9 0

Published with MATLAB 7.14

Copyright 2012 A ll rights res erved. N o part of this public ation may be reproduc ed or trans mitted without the expres s written c ons ent of the authors .