ABS Submersible Wastewater Pump AS 0530-0841: Applications
ABS Submersible Wastewater Pump AS 0530-0841: Applications
ABS Submersible Wastewater Pump AS 0530-0841: Applications
Type tested
and monitored
Applications
AS submersible pumps have been designed for the economic and
reliable pumping of wastewater and sewage, and can be used for
fixed applications with ABS automatic coupling system or as portable units.
* The 2-inch version is especially suitable for pumping wastewater from underground garages.
* With vortex hydraulics the AS is particularly suitable for fluids
containing fibrous or abrasive matter and for sewage.
* The Contrablock hydraulic system is suitable for larger proportions of solid or fibrous matter.
* Maximum allowable temperature of the medium is 40 C, or
short term to 60 C (max. 5 minutes).
Construction
The water pressure-tight, encapsulated fully flood-proof motor
and the pump section form a compact, robust, unit construction.
Motor
Single-phase 220-240 V and three-phase 400 V, 50 Hz, 2-pole (2900
r/min) and 4-pole (1450 r/min). Insulation class F; protection type
IP 68. Ex protection to Ex d IIB T4 and FM international standards.
Consult Sulzer Pumps for Ex usage with frequency inverters.
Bearings
The stainless steel motor shaft is supported in lubricated-for-life
ball bearings.
Shaft sealing
Between motor and hydraulic section by means of a high quality
sealing unit using a silicon carbide mechanical seal, independent
of direction of rotation and resistant to temperature shock. Seal at
motor side is by oil lubricated lip seal.
Discharge
AS 0530: G 2" internal thread (DN 50)
AS 0630 to 0641: radial slot DN 65 flange
AS 0830, 0831, 0840 & 0841: radial slot DN 80 flange
Features
* Hydraulic design with Contrablock system or vortex impellers.
* High reliability even under long term operating conditions.
* For wastewater and sewage containing solid or fibrous particles.
* In standard or Ex-versions.
* Option of automatic seal and temperature monitoring. Ex version with temperature monitoring as standard.
* Available for transportable or fixed installation.
Temperature monitoring
TCS (Thermo-Control-System) with thermal sensors in the stator
to switch off the pump in the case of overheating and switch on
automatically after cooling down (option on standard AS).
Materials
Seal monitoring
DI system consisting of a sensor in the motor and oil chambers
which signals an inspection alert if there is leakage at the shaft
seals (option on standard AS; not in oil chamber on Ex version).
Hydraulics
AS 0530, 0630, 0631, 0830, 0831: vortex, open, recessed four-vane
impeller.
AS 0641, 0840, 0841: Contrablock, open single-vane impeller with
spiral bottom plate.
Description
Material
Motor Housing
Rotor Shaft
Volute
Impeller
Bottom plate
Fasteners
Technical Data
Discharge *
0530S12/2W(1
S12/2D
S17/2D
S26/2D
Solids
size
(mm)
40
40
40
40
Motor power**
(kW)
P1P2
1.771.20
1.691.20
2.311.70
3.432.60
Rated
current
(A)
8.22
3.29
3.97
5.64
Speed
Weight ***
G 2"
G 2"
G 2"
G 2"
Rated
voltage
(V)
220-240 1~
400 3~
400 3~
400 3~
(r/min)
2900
2900
2900
2900
(kg)
31
31
34
40
0630S10/4W(1
S13/4D
S22/4D
60
60
60
DN 65
DN 65
DN 65
220-240 1~
400 3~
400 3~
1.691.00
1.931.30
2.882.20
7.49
3.60
5.15
1450
1450
1450
37
37
43
0631S12/2W(1
S12/2D
S17/2W(1
S17/2D
S30/2D
40
40
40
40
40
DN 65
DN 65
DN 65
DN 65
DN 65
220-240 1~
400 3~
220-240 1~
400 3~
400 3~
1.771.20
1.691.20
2.361.65
2.311.70
3.743.00
8.22
3.29
10.60
3.97
6.23
2900
2900
2900
2900
2900
35
35
35
35
42
0641S30/2D
45
DN 65
400 3~
3.743.00
6.23
2900
41
0830S10/4W(1
S13/4D
S22/4D
60
60
60
DN 80
DN 80
DN 80
220-240 1~
400 3~
400 3~
1.691.00
1.931.30
2.882.20
7.49
3.60
5.15
1450
1450
1450
40
37
43
0831S22/4D
0840S12/2W(1
S12/2D
S17/2D
S26/2D
0841S13/4D
S22/4D
80
30
30
30
30
80
80
DN 80
DN 80
DN 80
DN 80
DN 80
DN 80
DN 80
400 3~
220-240 1~
400 3~
400 3~
400 3~
400 3~
400 3~
2.882.20
1.771.20
1.691.20
2.311.70
3.432.60
1.931.30
2.882.20
5.15
8.22
3.29
3.97
5.64
3.60
5.15
1450
2900
2900
2900
2900
1450
1450
45
33
33
33
39
41
56
AS
(1
Start and Run capacitor to the following specification required in control panel.
Start:125-160F.Run:40F (2x20F) for S10/4W,30F for S12/2W & S17/2W
The recommended start time for the motors is two seconds.
Dimensions (mm)
AS
432
444
293
293
331
331
160
160
236
236
125
125
175
175
133
133
100
100
18
18
155
155
n.a.
n.a.
20
20
n.a.
n.a.
n.a.
n.a.
437
450
309
309
348
348
157
157
294
294
140
140
247
247
147
147
57
57
18
18
245
245
195
195
15
15
132
132
40
40
409
421
305
305
346
346
160
160
237
237
140
140
247
247
145
145
54
54
18
18
245
245
195
195
15
15
132
132
40
40
0641S30/2
428
308
346
160
237
140
247
148
54
18
245
195
15
132
40
437
450
307
307
408
408
160
160
294
294
200
200
342
342
147
147
88
88
18
18
275
275
195
195
20
20
182
182
25
25
0831S22/4
470
397
445
240
312
200
340
157
88
18
275
195
20
182
25
418
430
280
280
379
379
130
130
210
210
200
200
342
342
148
148
88
88
18
18
275
275
195
195
20
20
182
182
25
25
0841S13/4
S22/4
473
485
397
397
445
450
240
240
312
312
200
200
340
340
157
157
88
88
18
18
275
275
195
195
20
20
182
182
25
25
AS 0530
AS 0630 - 0841
85
85
90
0630, 0830,
0831 & 0841
100
*
*
A
**
A
C
C
G
G
F
B
B
K
L
N
* Lowest switch-off level; minimum switch-on level must be at least 100 mm higher.
** Elbow not supplied.
P
O
Performance Curves
AS 0530
AS 0831
12
11
10
9
2/
S2
S2
4
2/
6
5
4
0
2
98
40
20
8
60
80
16
AS 0840
100
24
120
140
120
140
32
AS 0841
12
11
10
9
S2
2/
7
6
S1
3/
4
S1
3/
4
5
4
S1
3
/4
1
52
40
20
8
60
16
61
1
77
80
100
24
H = Total Head; Q = Discharge Volume.Curves to ISO 9906 (60 Hz available on request)N.B. please use the ABSEL program to validate pump selection.
1
96
32
Accessories
Size
Part no.
AS
62320560
62320673
62320557
62320649
62320650
0530
0630-0641
0830 & 0840
0830/31/40/41
0830/31/40/41
1 x 1 m
1 x 2 m
1 x 3 m
1 x 4 m
1 x 5 m
3m
4m
6m
7m
62610632
62610775
31380007
31380008
31380009
31380010
31380011
61265065
61265093
61265069
61265096
0830/31/40/41
0830/31/40/41
0530-0641
3m
4m
6m
7m
61265081
61265099
61265085
61265102
0530-0841
61825001
62665103
61355002
42895016
61355012
61350526
Fasteners(galvanized steel)
bolts and gasket (bracket to pump)
anchor bolts (pedestal to base)
Guide Rail(galvanized steel)
General
0530-0841
Discharge Elbow(EN-GJL-250)
flange to thread
flange to STORZ coupling
DN 80 to G 2"
DN 80 to G 2"
31090131
62665074
0840
Adaptor(galvanized steel)
DN 65 to DN 80
21405002
G 2"
G 2"
DN 80
DN 80
61400527
61400543
61400534
61400523
0530
0630-0641
0830/31/40/41
0830/31/40/41
Gate Valve(brass)
(EN-GJL-250)
G 2"
DN 80
14040007
61420500
0530
0830, 0831,
0840 & 0841
Design
1.Ball bearings; lubricated-for-life
2
3
4
5
6
ABS submersible wastewater pump AS 0530-0841 2013-07-31 | We reserve the rights to alter specifications due to technical developments.
Fixed installation
with ABS Automatic
Coupling System
Description