Sharp Lc-32d44e S Ru-Bk Gy - Et

SERVICE MANUAL
LC32D44E/S/RU-BK/GY (1st Eddition)

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRE-
CAUTION............................................... .............i
PRECAUTIONS A PRENDRE LORS DE
LA REPARATION................................... ............ii
PRECAUTIONS FOR USING LEAD-FREE
SOLDER ................................................ ........... iii
CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS ................................. ........ 1-1
[2] OPERATION MANUAL .......................... ........ 1-2
[3] DIMENSIONS ........................................ ........ 1-5
CHAPTER 2. REMOVING OF MAJOR PARTS
[1] REMOVING OF MAJOR PARTS ........... ........ 2-1
CHAPTER 3. ADJUSTMENT
[1] After replacement of any PWB and/or IC for
repair, note the following. ............................... 3-1
[2] SOFTWARE UPDATING........................ ........ 3-1
[3] Entering and exiting the adjustment pro-
cess mode.............................................. ...... 3-18
[4] Remote controller key operation and de-
scription of display in adjustment process
mode. ..................................................... ...... 3-18
[5] Adjustment process mode menu.................. 3-19
[6] Special features............................................ 3-20
[7] Video signal adjustment procedure.............. 3-21
[8] White Balance Adjustment ........................... 3-22
[9] Adjusting procedure by use of [RS-232C] ...... 3-23
[10] Initialization to factory settings.....................3-24
[11] Lamp error detection ...................................3-24
[12] Public Mode (Hotel Mode) ...........................3-25
CHAPTER 4. TROUBLE SHOOTING TABLE
[1] TROUBLE SHOOTING TABLE .....................4-1
CHAPTER 5. MAJOR IC INFORMATIONS
[1] MAJOR IC INFORMATIONS.........................5-1
CHAPTER 6. BLOCK DIAGRAM/OVERALL WIRING
[1] BLOCK DIAGRAM.........................................6-1
[2] SYSTEM BLOCK DIAGRAM.........................6-3
[3] OVERALL WIRING DIAGRAM......................6-4
CHAPTER 7. PRINTED WIRING BOARD ASSEM-
BLIES
[1] MAIN Unit ......................................................7-1
[2] R/C, LED Unit ................................................7-5
[3] MINI AV Unit ..................................................7-6
[4] KEY ...............................................................7-7
CHAPTER 8. SCHEMATIC DIAGRAM
[1] DESCRIPTION OF SCHEMATIC DIA-
GRAM............................................................8-1
[2] SCHEMATIC DIAGRAM................................8-2
Parts Guide
TopPage
CONTENTS
No. S38F8LC32D44E
LCD COLOUR TELEVISION
LC-32D44E/S/RU-BK/GY MODELS
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its orig-
inal condition and only parts identical to those specified should be used.
i
LC32D44E-BK
Service Manual

SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRECAUTION
WARNING
1. For continued safety, no modification of any circuit should be
attempted.
2. Disconnect AC power before servicing.
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform the following
safety checks:
3. Inspect all lead dress to make certain that leads are not pinched,
and check that hardware is not lodged between the chassis and
other metal parts in the receiver.
4. Inspect all protective devices such as non-metallic control knobs,
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
the following manner.
Plug the AC cord directly into a 220~240 volt AC outlet.
Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-
leled by a 0.15F capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or elec-
trical ground connected to an earth ground.
Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-
sitivity or measure the AC voltage drop across the resistor.
Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
All checks must be repeated with the AC cord plug connection
reversed. (If necessary, a nonpolarized adaptor plug must be used
only for the purpose of completing these checks.)
Any reading of 1.05 V peak (this corresponds to 0.7 mA peak AC.)
or more is excessive and indicates a potential shock hazard which
must be corrected before returning the monitor to the owner.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD color television have
special safety-related characteristics.
These characteristics are often not evident from visual inspection, nor
can protection afforded by them be necessarily increased by using
replacement components rated for higher voltage, wattage, etc.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by and shaded areas in the Replacement Parts
List and Schematic Diagrams.
For continued protection, replacement parts must be identical to those
used in the original circuit.
The use of a substitute replacement parts which do not have the same
safety characteristics as the factory recommended replacement parts
shown in this service manual, may create shock, fire or other hazards.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the
servicing guidelines which follow:
CAUTI ON: FOR CONTI NUED PROTECTION
AGAINST A RISK OF FIRE REPLACE ONLY WITH
SAME TYPE FUSE.
F7101, F7103 (250V 3.15A)
F7102 (250V 1A)
DVM
AC SCALE
1.5k ohm
10W
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
0.15 F
TEST PROBE
ii
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
De nombreuses pices, lectriques et mcaniques, dans les tlvi-
seur ACL prsentent des caractristiques spciales relatives la s-
curit, qui ne sont souvent pas videntes vue. Le degr de protec-
tion ne peut pas tre ncessairement augmente en utilisant des
pices de remplacement talonnes pour haute tension, puissance,
etc.
Les pices de remplacement qui prsentent ces caractristiques sont
identifies dans ce manuel; les pices lectriques qui prsentent ces
particularits sont identifies par la marque " " et hachures dans la
liste des pices de remplacement et les diagrammes schmatiques.
Pour assurer la protection, ces pices doivent tre identiques celles
utilises dans le circuit d'origine. L'utilisation de pices qui n'ont pas
les mmes caractristiques que les pices recommandes par l'usine,
indiques dans ce manuel, peut provoquer des lectrocutions, incen-
dies, radiations X ou autres accidents.
AVERTISSEMENT
1.
2.
3.
4.
5.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
Ne peut effectuer la rparation qu' un technicien spcialis qui s'est parfaitement accoutum toute vrification de scurit et aux
conseils suivants.
N'entreprendre aucune modification de tout circuit. C'est danger-
eux.
Dbrancher le rcepteur avant toute rparation.
Inspecter tous les faisceaux de cbles pour s'assurer que les fils
ne soient pas pincs ou qu'un outil ne soit pas plac entre le chs-
sis et les autres pices mtalliques du rcepteur.
Inspecter tous les dispositifs de protection comme les boutons de
commande non-mtalliques, les isolants, le dos du coffret, les cou-
vercles ou blindages de rglage et de compartiment, les rseaux
de rsistancecapacit, les isolateurs mcaniques, etc.
S'assurer qu'il n'y ait pas de danger d'lectrocution en vrifiant la
fuite de courant, de la facon suivante:
Brancher le cordon d'alimentation directem-ent une prise de cou-
rant de 120V. (Ne pas utiliser de transformateur d'isolation pour
cet essai).
A l'aide de deux fils pinces, brancher une rsistance de 1.5 k
10 watts en parallle avec un condensateur de 0.15F en srie
avec toutes les pices mtalliques exposes du coffret et une terre
connue comme une conduite lectrique ou une prise de terre
branche la terre.
Utiliser un voltmtre CA d'une sensibilit d'au moins 5000/V pour
mesurer la chute de tension en travers de la rsistance.
Toucher avec la sonde d'essai les pices mtalliques exposes qui
prsentent une voie de retour au chssis (antenne, coffret mtalli-
que, tte des vis, arbres de commande et des boutons, cusson,
etc.) et mesurer la chute de tension CA en-travers de la rsistance.
Toutes les vrifications doivent tre refaites aprs avoir invers la
fiche du cordon d'alimentation. (Si ncessaire, une prise
d'adpatation non polarise peut tre utilise dans le but de termin-
er ces vrifications.)
La tension de pointe mesure ne doit pas dpasser 0.75V (corre-
spondante au courant CA de pointe de 0.5mA).
Dans le cas contraire, il y a une possibilit de choc lectrique qui
doit tre supprime avant de rendre le rcepteur au client.
PRECAUTION: POUR LA PROTECTION CON-
TINUE CONTRE LES RISQUES D'INCENDIE,
REMPLACER LE FUSIBLE
F7101, F7103 (250V 3.15A)
F7102 (250V 1A)
VERIFICATIONS CONTRE L'INCEN-DIE ET LE
CHOC ELECTRIQUE
Avant de rendre le rcepteur l'utilisateur, effectuer les vrifica-
tions suivantes.
DVM
ECHELLE CA
1.5k ohm
10W
0.15 F
SONDE D'ESSAI
AUX PIECES
METALLIQUES
EXPOSEES
BRANCHER A UNE
TERRE CONNUE
AVIS POUR LA SECURITE
iii
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Employing lead-free solder
PWBs of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
Using lead-free wire solder
When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause dam-
age or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 C, we recommend you to use a dedicated soldering
bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 C which is higher than the conventional lead solder by 40 C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
PARTS CODE
PRICE
RANK
PART
DELIVERY
DESCRIPTION
ZHNDAi123250E BL J 0.3mm 250g (1roll)
ZHNDAi126500E BK J 0.6mm 500g (1roll)
ZHNDAi12801KE BM J 1.0mm 1kg (1roll)
1 1
LC32D44E-BK
Service Manual

CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS
Item 32" LCD COLOUR TV
LCD panel 32" Advanced Super View & BLACK TFT LCD
Resolution 1,049,088 pixels (1,366 x 768)
Video Colour System PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
TV
Function
TV-Standard Analogue CCIR (B/G, I, D/K, L, L)
Digital DVB-T (2K/8K OFDM)
Receiving
Channel
VHF/UHF E2-E69ch, F2-F10ch, I21-I69ch, IR A-IR Jch, (Digital: E5-E69ch)
CATV Hyper-band, S1-S41ch
TV-Tuning System Auto Preset 99 ch, Auto Label, Auto Sort
STEREO/BILINGUAL NICAM/A2
Brightness 450 cd/m2
Viewing angles H : 176 V : 176
Audio amplifier 10W x 2
Speaker (100 mm x 35 mm) x 2
Terminals Antenna UHF/VHF 75 Din type (Analogue & Digital)
RS-232C 9 pin mini D-sub
EXT 1 SCART (AV input, Y/C input, RGB input, TV output)
EXT 2 SCART (AV input/output, Y/C input, RGB input, AV Link)
EXT 3 S-VIDEO (Y/C input), RCA pin (AV input)
EXT 4 3.5 mm jack (Audio input), 15 pin mini D-sub (PC)
EXT 5 Audio in, Component in
EXT 6 HDMI, 3.5 mm jack (Audio input)
EXT 7 HDMI
C. I. (Common Interface) EN50221, R206001
OUTPUT RCA pin (Audio)
Headphones 3.5 mm jack (Audio output)
OSD language English/German/French/Italian/Spanish/Dutch/Swedish/Portuguese/Finnish/Turkish/Greek/
Russian/Polish
Power Requirement AC 220-240 V, 50 Hz
Power Consumption 120 W (0.9 W Standby) (Method IEC60107)
Weight 11.0 kg (Display only), 13.0 kg (Display with stand)
Operating temperature 0C to +40C
As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of production
units. There may be some deviations from these values in individual units.
NOTE
Refer to inside back cover for dimensional drawings.
Optional accessory
The listed optional accessories are available for the
LCD colour TV. Please purchase them at your nearest
shop.
Additional optional accessories may be available in near
future. When purchasing, please read the newest catalogue
for compatibility and check the availability.
Part name Part number
Wall mount bracket
(LC-32D44E, LC-32D44S)
AN-37AG5
1 2
[2] OPERATION MANUAL
1
2
4
3
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
1 (Standby/On)
Enter standby mode or turn on the
power.
2 AV MODE
Select a video setting.
3 09
Set the channel in TV and DTV mode.
Set the page in Teletext mode.
4 (Flashback)
Press to return to the previous image
in normal viewing mode. (Will not work
while operating in EPG/ESG screen.)
5 (WIDE MODE)
Select the wide mode.
6 (Sound mode)
Select the sound multiplex mode.
(See below.)
7 EPG
DTV: To display EPG (Electronic
Programme Guide) screen.
8 ESG
DTV: To display ESG (Electronic Service
Guide) screen.
9 (Teletext)
Select the TELETEXT mode. (All TV
image, DTV/DATA image, all TEXT
image, TV/TEXT image)
DTV: Select DTV data broadcasting and
TELETEXT.
10 / / / (Cursor)
Select a desired item on the setting
screen.
11 END
Exit the menu screen.
12 (Reveal hidden Teletext)
13 (Freeze/Hold)
14 SURROUND
Switch the surround effects on and off.
15 RADIO
DTV: Switch between RADIO and DTV
mode.
16 (Mute)
Switch the sound on and off.
17 DTV
Press to access DTV mode while
watching other input sources, and vice
versa.
(This button will not work if you were
watching DTV immediately before
turning off the TV. In this case first select
any other input source except DTV
using the button.)
18 (+/-) (Volume)
(+) Increase the volume.
(-) Decrease the volume.
19 P ( / )
TV/DTV: Select the channel.
External: Switch to TV or DTV input
mode.
eletext: Move to the next/previous
20 (INPUT SOURCE)
Select an input source.
(TV, DTV, EXT1, EXT2, EXT3, EXT4,
EXT5, EXT6, EXT7)
21 SLEEP
Set the sleep timer on (in units of 30
min. up to max. 2 hr. 30 min) and off.
22 (Display information)
23 DTV MENU
DTV: Display DTV Menu screen.
24 MENU
Display the MENU screen.
25 OK
Execute a command within the menu
screen.
Display the programme list. (Except
external input.)
26 RETURN
Return to the previous menu screen.
27 (Subpage)
28 (Subtitle for Teletext)
TV/External: To turn the subtitles on and
off.
DTV: Display the subtitle selection
screen.
29 Colour (Red/Green/Yellow/Blue)
TELETEXT: Select a page.
DTV: The coloured buttons are used to
select correspondingly to the coloured
items in the menu screen.
NOTE
When no signal is input, the sound mode will display MONO.
NICAM TV broadcasts selection
Signal Selectable items
Stereo NICAM STEREO, MONO
Bilingual
NICAM CH A, NICAM CH B,
NICAM CH AB, MONO
Monaural NICAM MONO, MONO
A2 TV broadcasts selection
Signal Selectable items
Stereo STEREO, MONO
Bilingual CH A, CH B, CH AB
Monaural MONO
Using on the remote control unit
DTV mode:
Press to open the multi audio screen.
Analogue TV mode:
Each time you press , the mode switches as illustrated in the following
tables.
Remote control unit
When Sweden is selected in the
country setting from the Initial
auto installation, DTV channels
are 4-digit. When another
country is selected, DTV channels
are 3-digit.
1 3
TV (Front view)
TV (Rear view)
10
1
2
6
7
8
9
3 4 5
13 11
12
NOTE
Only if you use an active terrestrial antenna, select On (5V) under Supply Voltage.
Remote control sensor (Standby/On) indicator
(Power button)
(Input button)
(-/+) (Volume buttons)
P ( / )
(Programme [channel] buttons)
MENU button
1 RS-232C terminal
2 EXT 4 (ANALOGUE RGB/AUDIO)
terminals
3 EXT 5 (COMPONENT) terminals
4 EXT 1 (RGB) terminal
5 EXT 2 (RGB) terminal
6 Antenna input terminal
(DVB-T 5V=/80 mA)
7 OUTPUT (AUDIO) terminals
8 EXT 6 (HDMI/AUDIO) terminals
9 EXT 7 (HDMI) terminal
10 COMMON INTERFACE slot
11 EXT 3 terminals
12 Headphone jack
13 AC INPUT terminal
1 4
Appendix
Troubleshooting
Problem Possible Solution
No power. Check if you pressed on the remote control unit.
If the indicator on the TV lights up red, press .
Is the AC cord disconnected?
Check if you pressed on the TV.
Unit cannot be operated. External influences such as lightning, static electricity, etc., may cause improper
operation. In this case, operate the unit after first turning the power off, or
unplugging the AC cord and re-plugging it in after 1 or 2 minutes.
Remote control unit does not
operate.
Are batteries inserted with polarity (+, -) aligned?
Are batteries worn out? (Replace with new batteries.)
Are you using it under strong or fluorescent lighting?
Is a fluorescent light illuminated to remote control sensor?
Picture is cut off. Is the image position correct?
Are screen mode adjustments (4:3 Mode/WSS) such as picture size made
correctly?
Strange colour, light colour, or
dark, or colour misalignment.
Adjust the picture tone.
Is the room too bright? The picture may look dark in a room that is too bright.
Check the colour system setting.
Check the HDMI Setup setting.
Power is suddenly turned off. The units internal temperature has increased.
Remove any objects blocking vent or clean.
Check the power control setting.
Is sleep timer set? Press SLEEP on the remote control unit until it sets to Off.
No picture. Is connection to other components correct?
Is input signal type selected correctly after connection?
Is the correct input source selected?
Is non-compatible signal being input?
Is picture adjustment correct?
Is the antenna connected properly?
Is On selected in Audio Only?
No sound. Is the volume too low?
Make sure that headphones are not connected.
Check if you pressed on the remote control unit.
The DTV menu screen is displayed
in monochrome and hard to select
the item.
Check if Monochrome is set to On. If so, set it to Off.
The TV sometimes makes a
cracking sound.
This is not a malfunction. This happens when the cabinet slightly expands and
contracts according to change in temperature. This does not affect the TVs
performance.
Cautions regarding use in high and low temperature environments
When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly
delayed. This is not a malfunction, and the unit will recover when the temperature returns to normal.
Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the LCD panel to malfunction.
Storage temperature: -20C to +60C.
IMPORTANT NOTE ON RESETTING THE PIN
We suggest that you remove the following instruction from the operation manual to prevent children from
reading it. As this operation manual is multilingual, we also suggest the same with each language. Keep it in a
safe space for future reference.
1 5
[3] DIMENSIONS
200.0
200,0
776.0
776,0
73.9
73,9
94.5
94,5
402.0
402,0
230.0
230,0
699.2
699,2
3
9
3
.
8
3
9
3
,
8
3
3
2
.
0
3
3
2
,
0
5
2
3
.
0
5
2
3
,
0
1
1
0
.
0
1
1
0
,
0
5
2
.
0
5
2
,
0
5
7
5
.
0
5
7
5
,
0
2
0
0
.
0
2
0
0
,
0
2 1
LC32D44E-BK
Service Manual

CHAPTER 2. REMOVING OF MAJOR PARTS
[1] REMOVING OF MAJOR PARTS
1. Remove the 4 lock screws and detach the Stand.
2. Remove the 3 lock screws , 6 lock screws , 2 lock screw and detach the Rear Cabinet.
1
2
3 4
Front Cabinet
Rear Cabinet
Stand
2
3
4
1
2 2
3. Remove the 3 lock screws , 2 lock screws , 1 lock screws and detach the Main Shield.
4. Disconnect all the connectors from all the PWBs.
5. Remove the KEY Unit Ass'y .
5A 5B 6
7
[LB]
[PD]
[LB]
[PD]
[KM]
[SP]
[RA]
[FPC]
[KM]
Main Shield
KEY Unit
Operation Button
SP-R
5A
5B
6
7
SP-L
2 3
6. Remove the Speaker (L) , (R) .
7. Remove the 4 lock screws and detach the POWER/INVERTER Unit.
8. Remove the 2 lock screws , and detach the MAIN Unit.
9. Remove the 2 lock screws and detach the MINI AV Unit.
8 9
10
11
12
Power/Inverter Unit
MINI AV Unit
Speaker(R) Speaker(L)
MINI AV Cover
Main Unit
11
9 8
12
10
2 4
10.Remove the 1 lock screw and detach the Bottom Cover.
11. Remove the 4 lock screws and detach the Stand Fix Angle.
12.Remove the R/C, LED Unit .
13
14
15
R/C,LED Unit
Stand Fix Angle
Bottom Cover
14
15
13
2 5
13.Remove the 6 lock screws and detach the LCD Panel Module.
14.Remove the 2 lock screws and detach the LCD Fix Angle-A.
15.Remove the 2 lock screws and detach the LCD Fix Angle-B.
16.Remove the 8 lock screws and detach the Panel Fix Angle.
16
17
18
19
LCD Fix Angle-A
LCD Fix Angle-A
Panel Fix Angle
17 16
19
19
16
16
LCD Fix Angle-B
LCD Fix Angle-B
18
16
17
16
18
16
3 1
LC32D44E-BK
Service Manual

CHAPTER 3. ADJUSTMENT
[1] After replacement of any PWB and/or IC for repair, note the following.
When replacing the following units, be sure to prepare the new units loaded with updated software.
Note that an IC into which ROM data is written is available for MAIN-UNIT servicing (see below)
[2] SOFTWARE UPDATING
There are 2 methods to update software in the VCTp: I2C method, RS-232C HyperTerminal and RS-232C Tera Term method.
RS-232C method is allowed when the TV is working properly and the action should be only software upgrade.
1. RS-232C Method Description (HyperTerminal).
The hardware tools requirement are:
1. A Modem-null (Cross type) DB9 female to DB9 female cable.
2. Make the connections as indicated in the figure:
Before using RS-232C updating method is necessary to configure a Terminal PC software. HyperTerminal has been selected as a Terminal soft-
ware because its include in all Windows versions as an accessory, and you can find it inside Accessories\Communications folder. For this rea-
son, please follow carefully the next steps:
1) First time HyperTerminal is used, its necessary to configure some settings. Follows next action to configure two connection: low speed
(9600bps) and high speed (115200bps).
2) Create a New Connection file with name P55_9600bps.
3) Select a free COM port and select the Port Settings properties as follows:
MAIN-UNIT: DUNTKE449FM02
IC1902 RH-iXC448WJZZS EDID (HDMI)
IC1922 RH-iXC447WJZZS EDID (HDMI)
IC2321 RH-iXC206WJQZS EDID (PC)
IC8101 RH-iXC639WJZZS EEPROM
Computer TV set
RS-232C
IOIOI
TV Set
3 2
4) Click on File\Properties menu for selecting the General and ASCII properties as follows:
5) Select New Connection in the File Menu.
6) Answer Yes to close current connection and Yes to save session P55_9600bps.
7) Create a new connection with the name P55_115200bps.
8) Select a the same COM port used in item 2 and select the Port Settings properties as follows:
9) Select the same General and ASCII properties as item 3.
10)Close HyperTerminal session, answering Yes to close current connection and Yes to save session P55_115200bps.
To start updating session, click over P55_9600bps icon that you can find in the START\All programs\Accessories\ Communications\HyperTermi-
nal\HyperTerminal folder and follow next procedure:
3 3
1) Check the connection between TV set and PC, sending a wrong command, as for example: aaa. TV set returns an ERR label as an syntaxis
ERROR (Not correct order or sequence).
2) Send the command DWMD to enter TV set in Download Mode. The TV set answer sending same symbol continuosly. If this symbol character
doesnt appear, please dont worry and pass to next step.
3) Close this connection and open P55_115200bps connection clicking over the P55_115200bps that you can find in START\All pro-
grams\Accessories\ Communications\HyperTerminal\HyperTerminal folder.
4) Using Transfer\Send file... menu, select desired file (.bin format) and the transmission protocol (Xmodem) as show below.
5) After press Send button the updating process starts as follows:
6) When flash update process finishes, the Flash Programming Complete label appears in the screen, the device automatically go to switch off,
and in a few seconds go to switch on again.
VERY IMPORTANT NOTE:
During the updating time, please dont use the PC for other purpouses, in order to abolish communication problems between TV set and
PC. If TV set was not updated properly, the TV wont have the software to startup again, and you must follow the I2C method to update
another time the TV set.
3 4
2. RS-232C Method Description (Tera Term)
The hardware tools requirement are:
1. A Modem-null (Cross type) DB9 female to DB9 female cable.
2. Make the connections as indicated in the figure:
Software requirements:
To upgrade VCTp software from RS-232C external connector is necessary to use a Tera Term (Pro) free software.
The URL of Tera Term home page is:
http://hp.vector.co.jp/authors/VA002416/teraterm.html
(The address may be changed in future)
Tera Term (Pro) supported operating systems:
MS-Windows 95 or upper
MS-Windows NT 3.5 and 4.0 or upper
Note.- For Windows 3.1 use Tera Term version 1.X.
Copy all the distribution files to an empty floppy disk or temporary directory (for example C:\ TEMP).
Run SETUP.EXE and follow the instruction given by it.
After the installation, the distribution? les are no longer needed, you can delete them or may keep them in the floppy disk.
How to use Tera Term Pro:
When the Tera Term (Pro) program is used, its necessary to shape some settings. Follows next action to configure the connection:
Computer TV set
RS-232C
IOIOI
TV Set
3 5
1) Select: SerialCOM X O.K.
2) Select: Terminal
3) Choose the same options as the above picture.
3 6
4) Select: Setup Serial port O.K. Appear the follow screen:
5) Select follows settings:
6) Check the connection between TV set and PC, sending a wrong command, as for example: aaa. TV set returns an err label as an syntaxes
ERROR (Not correct order or sequence).
Send a DWMD (capital letters) command to enter TV set in Download Mode.
Change a baud rate to 115200.
Select: Setup Baud rate 115200 O.K.
Serial port to use: COM x
Baud rate: 9600
Data: 8 bits
Parity: none
Stop: 1 bit
Flow control: none
Enter O.K.
3 7
7) Select: File Transfer XMODEM Sent
8) Choose the file for upgrade and click Open.
9) After select Open the upgrade process starts as follows:
3 8
10)When flash update process finishes, the Flash programming complete label appear in the screen, the device automatically go to switch off, and
in a few seconds go to switch on again.
VERY IMPORTANT NOTE:
During the updating time, please dont use the PC for other purposes, in order to abolish communication problems between TV set and PC.
If TV set was not updated properly, the TV wont have the software to startup again, and you must follow the I2C method to update
another time the TV set.
3. How to update the Digital Board Software.
There are 2 methods to update the Digital Board Software on Flash Memory (IC4251) throught the Digital Processor (IC4001).
RS-232 Method (From PC trough RS-232C COM port).
PCMCIA CARD (Compact Flash Memory) Method.
NOTE: The PCMCIA method is only compatible with those PCs running XP Windows Version.
3.1. Jig RS-232 Method Description
Hardware requirements:
1. A modem null (Cross type) DB9 female to DB9 female cable.
2. Make the connections as in the below figure.
Software requirements:
1. Winupload application software on PC.
~
~
Computer
TV Set
(CI Terminal)
Jig
RS-232C serial control cable
(cross type, commercially available)
RS-232C
IOIOI
TV Set
3 9
How to setup the Winupload software for the first time:
1. Start Winupload. It will appear the following picture.
2. Select the most suitable RS232 Serial Port from Port Setting - Process Menu.
3. Select the following settings from Port Settings Menu.
Bits Per Second: 115200
Parity: None
Data bits: 8
Stop bits: 1
Hardware Flow Control: OFF
Procedure for updating the TV set.
1. Switch off the TV set to be updated, in DTV mode.
2. Start Winupload. It will appear the following picture on PC.
3 10
3. Establish connection on Winupload Software.
4. Select Upload URT file
5. Select and open the .urt data file from data directory
NOTE: Consider the version shown below just an example, may be is not the latest one, and could be different depending on the TV set destination
(market/Country) or model.
6. Switch On the TV Set (previously in DTV Mode). The Uploading Process starts automatically.
3 11
While the TV set is uploading the software, the following information is shown on the TV set screen.
Then, data transfer from PC to TV set finishes when the Upload progress completed label appears in the Winupload screen. Now, the TV set made
some additional verification (Items #2 to #7). When the full uploading process is finished, in the Winupload window appears the label Preparing to
start application for a new TV Set, and just now, in the TV screen of the updated set, appears a congratulations label (Item #8).
NOTE: Do not turn off the TV set while the software updating was in progress.
7. Unplug the AC cord.
8. Disconnect the Jig from TV Set.
Software Version verification procedure.
1. Connect the AC cord and Switch On the TV Set.
2. Select DTV Menu on TV Set. The following On Screen Display will appear.
3. Select Version. The updated version can be verified.
NOTE: Consider the version shown above just as example, may be is not the latest one, and could be different depending on the TV set destination
(market/Country) or model.
3 12
4. Software Version Upgrade Using Card
1. Write the software (ATV and DTV) on the PCMCIA CARD by following the procedure described in the separate document, How to write software
(ATV and DTV) to PCMCIA CARD.
(* In the document, both ATV and DTV are written; you may write either of them.)
(You can equally use any version after Storage Media Manager Version 1.3.1.)
2. Turn off the power.
(* You can select either of the mode ATV or DTV. In this document, ATV is selected.)
3. Insert the PCMCIA CARD with the upper side facing up into the card slot.
(* Do not insert the card with the upper side facing down.)
4. Turn on the power. After a short time, the message, SYSTEM SOFTWARE UPDATE IN PROGRESS. ...) appears and the software upgrade
starts.
If the ATV software upgrade is necessary, the step proceeds to (5); if unnecessary, the DTV software upgrade starts and the step proceeds to (7).
5. If the ATV software upgrade is necessary, the following display appears and the upgrade starts.
When the status bar reaches 100 %, the ATV upgrade is complete. Then the system restarts from the ATV mode. The step proceeds to (6).
3 13
6. The message, SYSTEM SOFTWARE UPDATE IN PROGRESS. ... appears again and the DTV software upgrade starts. Then the step proceeds
to (7).
7. After a short time, the message, Congratulations! ... appears. The upgrade is complete.
(Note: You cannot downgrade the ATV software but can downgrade the DTV software.)
3 14
How Lo wrlLe cofLware,A1V aod 01V) Lo PCVC|A CAP0 OJ0ec2OO7
wrlLeo by KeoLaro 6eyama,6HAPP Japao)
1.wHeo you wrlLe c/w , you cHould uce 6LorageVedlaVaoagerA1V-01V 1.J.1.exe
2.6LarL 6LorageVedlaVaoagerA1V-01V 1.J.1.exe.,0lcplayed ac followc.)
J.PormaL LHe 0rlve
4.CHooce folder
Cllck LHe rlgHL buLLoo aL L. drlve,1He drlve LHaL LHe
medla for PCVC|A updaLe ls lnserted lo.).
Aod , cHooce PormaL 0rlve.
CHooce LHlc folder.
3 15
6.wrlLe A1V cofLware
6-1)CHooce Add A1V Blo ...
6-2)6elecL LHe A1V cofLware.,6orry for dlcplayed by Japaoece.)
6-J)|opuL maor code aod mloor code.
|opuL LHe maor code aod mloor code.
--Lx.---
wHeo you would llke Lo wrlLe c/w vercloo O.6O6 ,
you cHould lopuL ac followc.
A1V Plrmware maor.OO
A1V Plrmware mloor.6O6
Aod , precc OK.
-----
CHooce Add A1V
Blo...
3 16
6-4)walL for LHe flolcH.
6-6)A1V cofLware wrlLlog lc cucceced.
6.wrlLe 01V cofLware
6-1)CHooce folder aod drag aod drop LHe 01V cofLware.
Added LHe A1V cofLware.
3 17
6-2)walL for LHe flolcH.
6-J)01V cofLware wrlLlog lc cucceced.
7)CHooce Plle --` LxlL ,flolcH LHe 6LorageVedlaVaoagerA1V-01V 1.J.1)
PlolcH
0rag & 0rop LHe 01V cofLware
CHooce LHe folder wHlcH you
cLorec LHe 01V cofLware LHaL
you waoL Lo wrlLe lo.
Added LHe 01V cofLware.
3 18
[3] Entering and exiting the adjustment process mode
1) Unplug the AC power cord of running TV set to force off the power.
2) While holding down the VOL (-) and INPUT keys on the set at once, plug in the AC power cord to turn on the power.
The letter appears on the screen.
3) Next, hold down the VOL (-) and P( ) keys on the set at once.
Multiple lines of orange characters appearing on the screen indicate that the set is now in the adjustment Process mode.
If you fail to enter the adjustment process mode (the display is the same as normal startup), retry the procedure.
4) To exit the adjustment process mode after the adjustment is done, unplug the AC power cord to force off the power. (When the power is turned off
with the remote controller, once unplug the AC power cord and plug it in again. In this case, wait 10 seconds or so before plugging.)
[4] Remote controller key operation and description of display in adjustment process mode.
1. key operation
* Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.
2. Description of display
Caution: Use due care in handling the information described here lest the users should know how to enter the adjustment process mode.
If the settings are tampered with in this mode, unrecoverable system damage may result.
Remote controller key Main unit key Function
P ( / ) P ( / ) Moving an item (line) by one (UP/DOWN)
(+ / ) (+ / ) Changing a selected line setting (+1/-1)
Cursor ( / ) Turning a page (PREVIOUS/NEXT)
Cursor ( / )
Changing a selected line setting (+10/-10)
Input button on remote
controller
Input button Input source switching (toggle switching)
(TVDTVEXT1EXT2EXT3EXT4EXT5EXT6)
OK Executing a function
(1) Current page/Total pages (3) Currently selected input
(4) Current colour TV system
(5) Destination
1/11 [INFO] TV AUTO XX:EURO
Dev Version
Pic Version
TEMP SENSOR
Dev Loader Version
Adjustment process
menu header
(7) Parameters
LEW07 01.XX (XX/XX/XXX)
(2) Current page title
NORMAL STANDBY CAUSE
ERROR STANDBY CAUSE
XX
XX
XX
XX
Main Version
XX
[1] 0
[2] 0
[3] 0
[4] 0
[5] 0
00H 00M
00H 00M
00H 00M
00H 00M
00H 00M
XX
3 19
[5] Adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
Page Line Item Description Remarks (adjustment detail, etc.)
1/11 [INFO]
1 Main Version LEW07 01XX(XX/XX0/XX) Main microprocessor version
2 Dev Version XX DTV microprocessor version
3 Dev Loader Version XX DTV microprocessor-Loader version
4 Pic Version xxxxxx Pic MICON version
5 TEMP SENSOR xxxxxx
6 NORMAL STANDBY CAUSE RC_STANDBY
7 ERROR STANDBY CAUSE [1] 00H 00M Error standby cause Total operating time before error
[2] 00H 00M
[3] 00H 00M
[4] 00H 00M
[5] 00H 00M
2/11 [INIT]
1 Factory Init [EURO/RUSSIA/SWEDEN] Initialization to factory settings execution
2 Inch Setting XX Inch present setting
3 Public Mode OFF/ON HOTEL MODE flag setting
4 Center Acutime xxH xxM Main operating hours
5 RESET OFF/ON Main operating hours reset
6 Backlight Acutime xxH xxM Backlight operating hours
7 RESET OFF/ON Backlight operating hours reset
8 Picture Read Pos X 0-xxx x-axis setting of picture data
9 Picture Read Pos Y 0-xxx y-axis setting of picture data
10 Picture Read ON/OFF Start/stop of picture data
3/11 [PAL.SECAM.N358]
1 RF-AGC ADJ ENTER RF-AGC auto adjustment execution
2 PAL+TUNER ADJ ENTER PAL TUNER auto adjustment execution
3 PAL ADJ ENTER PAL auto adjustment execution
4 TUNER ADJ ENTER TUNER auto adjustment execution
5 CONTRAST SD 32 PAL contrast adjustment
6 SECAM CB OFFSET 1 SECAM offset adjustment
7 SECAM CR OFFSET 1 SECAM offset adjustment
8 TUNER A DAC 32 TUNER DAC adjustment
9 RF AGC 16 RF AGC adjustment
4/11 [COMP 15K]
1 COMP 15K ADJ ENTER COMP15K auto adjustment execution
2 COMP 15K CONTRAST 40 Contrast adjustment
5/11 [HDTV]
1 HDTV CONTRAST 41 HDTV Contrast adjustment
6/11 [SMPTE]
1 RF-AGC ADJ ENTER RF-AGC auto adjustment execution
2 PAL-AGC ADJ ENTER PAL AGC auto adjustment execution
3 PAL ADJ ENTER PAL auto adjustment execution
4 TUNER ADJ ENTER TUNER auto adjustment execution
5 CONTRAST SD 30 PAL contrast adjustment
6 SECAM CB OFFSET 1 SECAM offset adjustment
7 SECAM CR OFFSET 1 SECAM offset adjustment
8 TUNER A DAC 36 TUNER DAC adjustment
9 RF AGC 16 RF AGC adjustment
7/11 [M GAMMA INFO]
1 M GAMMA IN 1 160 W/B adjustment, gradation 1 input setting
7 M GAMMA WRITE OFF/ON EEP writing of adjustment values
8 M GAMMA RESET OFF/ON Initialization of adjustment values
3 20
[6] Special features
* ERROR STANDBY CAUSE (Page 1/11)
The total time when the unit enters the standby due to operational error and cause of error are recorded on EEPROM as much as possible.
The values can be used to locate the fault for repair.
* EEP CLEAR (Page10/11)
Clear of process adjustment EEP value.
Page Line Item Description Remarks (adjustment detail, etc.)
8/11 [M GAMMA 1-3]
1 M GAMMA R 1 0 W/B adjustment, gradation 1R adjustment value
2 M GAMMA G 1 0 W/B adjustment, gradation 1G adjustment value
3 M GAMMA B 1 0 W/B adjustment, gradation 1B adjustment value
9/11 [M GAMMA 4-6]
10/11 [ETC]
1 EEP CLEAR OFF/ON Clear of all adjustment value
2 EEP CLEAR B OFF/ON Clear of adjustment value of B mode
3 STANDBYCAUSE RESET OFF/ON Reset of STANDBY CAUSE
4 AUTO INSTALLATION SW 0/1 1: * * * 0: * * *
5 OPTION 0
6 COUNTRY AUTO/EURO/UK Destination setting
7 L ERR RESET 0 LAMP ERR RESET Initializatio of L_ERR
8 L ERR STOP 0/1 LAMP ERR Inhibit L_LRR detection
9 DTV CLR ENTER Clear of DTV setting
10 I2C-OFF ENTER I2C DATA execution
11/11 [COM-BIAS]
1 VCOM ADJ 63 INVERTER drive frequency setting
2 TEST PATTERN 0 INVERTER drive frequency setting
3 21
[7] Video signal adjustment procedure
* The adjustment process mode menu is listed in Section 5.
1. Signal check
1. Signal generator level adjustment check (Adjustment to the specified level)
2. Entering the adjustment process mode
1. Enter the adjustment process mode according to Section 3.
3. RF AGC adjustment
4. PAL signal & tuner adjustment
Composite signal PAL : 0.7Vp-p 0.02Vp-p (Pedestal to white level)
15K component signal (50 Hz) : Y level 0.7Vp-p 0.02Vp-p (Pedestal to white level)
PB, PR level 0.7Vp-p 0.02Vp-p
Adjustment point Adjustment Conditions Adjustment procedure
1 Setting [Signal]
PAL
Sprit Field Colour Bar
RF signal UV
[Terminal]
TUNER
Feed the PAL Sprit Field colour bar signal to TUNER.
Signal level: 55 dB V +1dB, -1dB (75 LOAD)
2 Auto adjustment
performance
Adjustment process
Page3
Bring the cursor on [ RF AGC ADJ] and press [OK]
[***OK***] appears when finished.
1 Setting [Signal]
PAL
Full Field Colour Bar
Composite or RF signal
[Terminal]
EXT1 SCART IN
TUNER
Feed the PAL full field colour bar signal (75% colour saturation) to
EXT1 SCART IN.
Feed the RF signal (PAL colour bar) to TUNER.
Make sure the PAL colour bar pattern has the sync level of 7:3 with
the picture level.
2 Auto adjustment
performance
Adjustment process
Page3
Bring the cursor on [ PAL + TUNER ADJ] and press [OK]
[E-12CH]
100% white
100% white
jVIDEO IN SIGNAL]
100% white
[RF Signal]
3 22
5. ADC adjustment (Component 15K)
[8] White Balance Adjustment
Adjustment gradation values (IN) appear on page 7/11 of process adjustment, and adjustment initial values (offset value) appear on pages 8/11 and
9/11. For white balance adjustment, adjust the offset values on pages 8/11 and 9/11.
[Condition of the unit for inspection] Modulated light: MAX (+8)
[Adjustment reference device] Minolta CA-210
[Adjustment]
Check that the values on page 7/11 of process adjustment are set as below. If not, change them accordingly.
1) Display the current adjustment status at point 6. (Page 8/11 of process adjustment)
The display for checking the adjustment status is toggled by pressing the 6 button on the remote control.
(Normal OSD display 6 display for check (OSD disappears) 6 normal OSD display )
2) Read the value of the luminance meter.
3) Change M GAMMA R6/M GAMMA B6 (Adjustment offset value) on page 9/11 of process adjustment so that the values of the luminance meter
approach x = 0.272 and y = 0.277.
(Basically, G is not changed. If adjustment fails with R and B, change G. When G is lowered, the weaker of R and B must be fixed.)
4) If G is changed in step 3), change the values of M GAMMA G1-M GAMMA G5 on pages 8/11 and 9/11 of process adjustment as follows. When not
changed, go to step5).
Offset value of M GAMMA G1 = (Offset value of M GAMMA G6) * (160/960)
5) Display the adjustment status of the current point 5. (Each time the 5 button on the remote control is pressed, the adjustment status check dis-
play is toggled.)
(Normal OSD display 5 Check display (OSD disappears) 5 Normal OSD display )
Change M GAMMA R5/M GAMMA B5 (adjustment offset value) on page 9/11 of process adjustment so that the values of the luminance meter
approach x = 0.272 and y = 0.277.
6) Repeat step 5) for points 4, 3, 2, and 1.
[Adjustment reference standard value]
1 Setting [Signal]
COMP15K, 50Hz
100% Full Field Colour Bar
[Terminal]
EXT5 COMPONENT IN
Feed the COMPONENT 15K 100% full field colour bar signal
(100% colour saturation) to EXT5 COMPONENT IN.
2 Auto adjustment
performance
Adjustment process
Page4
Bring the cursor on [ COMP15K ADJ] and press [OK]
M GAMMA IN 1 160 M GAMMA IN 2 320
Adjustment spec 0.004 Inspection spec 0.006 (point 1)
Adjustment spec 0.002 Inspection spec 0.004 (Excluding the above-mentioned)
100% white
Black
3 23
[9] Adjusting procedure by use of [RS-232C]
1) Get ready the PC with COM port (RS-232C) running on Windows 95/98/ME/2000/XP operating system, as well as the RS-232C cross cable.
2) Start the unit with the RS-232C cable connected.
3) Start the terminal software. (The freeware readily available on the Internet will do.)
4) Make the following settings.
5) If the settings are correct, the terminal software indicates "ERR" against pressing of the "ENTER" key.
6) After the settings are done correctly, it is possible to make an adjustment by typing in the command shown in the table below and pressing the
"ENTER" key on the keyboard.
7) Command entry is successful if the terminal software indicates "OK" when the "ENTER" is pressed. If "ERR" is shown, retry to enter the command.
8) Send the process mode switching command to switch from the RS232C operation mode to the process mode.
KRSW0001: "ERR" is returned.
KKT10037: When "OK" is returned, the process mode becomes active. When "ERR", start over from KRSW0001.
9) Send each adjustment command.
RS-232C command list
Baud rate 9,600 bps
Data LENGTH 8 bit
Parity bit None
Stop bit 1 bit
Flow control None
Command Function Remarks
KYOF0000 Remote control disabled
OSDS0001 OSD display inhibited
SBSL0016 Light control level MAX
MSET0001 Background adjustment start
MSET0004 Initialization of adjustment value
LEV60928 Gradation 6 (928-gradation adjustment)
MG6G **** Adjustment of G of gradation 6 0000 ~4095
MG6R **** Adjustment of R of gradation 6 0000 ~ 4095
MG6B **** Adjustment of B of gradation 6 0000 ~ 4095
MG5G **** Input of G of gradation 5 Calculated value
MG5R **** Input of R of gradation 5 0000 ~4095
MG5B **** Input of B of gradation 5 0000 ~ 4095
MG4G **** Input of G of 4 Calculated value
MG4R **** Input of R of 4 0000 ~4095
MG4B **** Input of B of 4 0000 ~ 4095
MG3G **** Input of G of 3
MG3R**** Input of R of 3 0000 ~ 4095
MG3B **** Input of B of 3 0000 ~ 4095
LEV20352 Gradation 2 (352-gradation adjustment) Calculated value
MG2G **** Input of G of 2 0000 ~ 4095
MG2R **** Input of R of 2 0000 ~ 4095
MG2B **** Input of B of 2 0000 ~ 4095
LEV10184 Gradation 1(176-gradation adjustment)
MG1G **** Input of G of 1 Calculated value
MG1R **** Input of R of 1 0000 ~ 4095
MG1B **** Input of B of 1 0000 ~ 4095
MSET0003 Writing of adjustment value
3 24
[10] Initialization to factory settings
[11] Lamp error detection
1. Function description
This LCD colour television has a function (lamp error detection) to be turned OFF automatically for safety when the lamp or lamp circuit is abnormal
If the lamp or lamp circuit is abnormal, or some other errors happen, and the lamp error detection is executed, the following occur.
1- The main unit of television is turned OFF 5 seconds after it is turned ON. (The power LED on the front side of TV turns from green to red.)
2 - If the situation 1 happens 5 times sequentially, the power is turned on (relay is turned ON).
However, the backlight is not turned on, and then the relay is turned OFF after 5 to 6 seconds. (The power LED turns from green to red.)
2. Countermeasures
When television is turned OFF by the lamp error detection mentioned above, it enters the adjustment process with the power LED red. Entering the
adjustment process turns OFF the error detection and turns ON TV. This enables the operation check to detect errors in the lamp or lamp circuit
Check whether L ERROR RESET on point 7, page 10/11 of the adjustment process is 1 or more. If it is 1 or more, it indicates the lamp error detec-
tion was executed. After confirming that the lamp or lamp circuit is normal, reset the lamp error counter pushing OK in the R/C. After resetting
counter the label ***OK*** appears on Screen.
3. Reset standby cause error list
After confirming that the lamp error counter has been erased, select STAND BY CAUSE RESET on point 3, page 10/11 of the adjustment process
and select ON using the right cursor. For execute press OK in the R/C and the label ***OK*** appears on Screen.
Caution: When the factory settings have been made, all user setting data, including the channel settings, are initialized.
(The adjustments done in the adjustment process mode are not initialized.) Keep this in mind when initializing these settings.
Adjustment item Adjustment conditions Adjustment procedure
1 Factory settings Forcibly turn off the power
(See to below caution)
Enter the adjustment process mode.
Move the cursor to [Factory Init] on page 2/11.
Use the R/C key to select a destination [EURO/RUSSIA/
SWEDEN]. And, press the [OK] key.
EXECUTING... appears and initialization starts.
After a while, *** OK *** appears and the setting is complete.
NOTE: Never turn the power off during initialization.
When performing factory settings (while displaying page 2 of adjustment
process), confirm that the item Inch Setting or the panel size displayed
in the upper right corner corresponds to each panel size.
The following settings will be back to their factory ones.
1. User settings
2. Channel data (e.g. broadcast frequencies)
3. Maker option setting
4. Password data
After adjustments, exit the adjustment process mode.
To exit the adjustment process mode, unplug the AC power cord from the outlet to forcibly turn off the power.
When the power is turned off with the remote control, unplug the AC power cord and plug it back in (wait approximately 10 seconds before plugging
in the AC power cord)
3 25
[12] Public Mode (Hotel Mode)
1. How to Enter in the Public Mode (Hotel Mode).
Turn on the power and enter in the Adjustment Process mode as usual.
In the [INIT], Page 2/11 of Service, turns ON the Public Mode option.
Turn off TV by pressing Main Power switch.
While pressing VOL+ and INPUT keys at the same time, press Main Power switch for more than 2 seconds.
Then, when you are asked for the password, enter 027.
After this sequence the TV will turn on showing the Public Mode setting screen as follows:
Is possible to select each item of function by pressing cursor UP/DOWN keys on the remote control or CH( )( ) keys on the LCD TV. (Except
DTV)
The setting position of each item of functions is made by pressing cursor RIGHT/LEFT keys on the remote control or VOL (+) / (-) keys on the LCD
TV.
Select EXECUTE position after you set all function, and press cursor RIGHT/LEFT keys on the remote control or VOL (+) / (-) keys on the LCD TV for
confirmation.
2. Public Mode Settings.
1. POWER ON FIXED [VARIABLE FIXED]
When it is set to FIXED the TV is impossible to be switch off by Main Switch or Remote Control.
2. MAXIMUM VOLUME [0 60]
Is possible to set the maximum volume at limited level.
3. VOLUME FIXED [VARIABLE FIXED]
Is possible to fix the sound volume at limited level.
When FIXED is selected the sound volume before limited is fixed.
4. VOLUME FIXED LEVEL [0 60]
If FIXED has been selected, is possible to set a fixed volume at the level that is chosen.
5. RC BUTTON [RESPOND NO RESPOND]
If NO RESPOND is selected, the remote control keys are inoperative.
6. PANEL BUTTON [RESPOND NO RESPOND]
If NO RESPOND has been selected, the sets keys remain deactivated (Except POWER key).
7. MENU BUTTON [RESPOND NO RESPOND]
If NO RESPOND has been selected, MENU key, of remote control, is inoperative.
8. ON SCREEN DISPLAY [YES NO]
If NO has been selected, the On Screen Display does not appear.
9. INPUT MODE START [NORMAL TV (X) DTV INPUT1 INPUT2 INPUT3 INPUT4 INPUT5]
When any other item than NORMAL has been selected, the sets will start in a selected input mode at the next power-on.
10.INPUT MODE FIXED [VARIABLE FIXED]
FIXED has been selected, any channels and input modes other than those selected at the start mode cannot be picked up.
3 26
11. RESET
Cancel all Public Mode settings. (It returns to the factory settings)
12.EXECUTE
Select this item, and press cursor RIGHT / LEFT keys on the remote control or VOL (+) / (-) keys on the LCD TV for confirmation the functions set-
tings.
4 1
LC32D44E-BK
Service Manual

CHAPTER 4. TROUBLE SHOOTING TABLE
[1] TROUBLE SHOOTING TABLE
No power supply (Front LED does not light up) and no power-up even if turned on (Front LED light up).
Is the wire harness in the unit properly connected?
NO
Reconnect and recheck the wire harness.
YES
Are F7101 and F7103 normal?
NO
Are L7101-2, L7110, C7104-5, VA7103, D7101, etc. faulty? Check if
the peripheral circuits are short-circuited.
YES
Is F7102 normal?
NO
Are T7101, D7104, TH7101, C7118, etc.faulty? Check if the periph-
eral circuits are short-circuited.
YES
Is BU5V supplied from PIN(11) of connector CN7201
when the power switch is turned on?
NO
Check the peripheral circuits on the primary side of IC7101, T7101,
etc. and the secondary side of D7222, D7215, L7206, PC7104, etc.
YES
Is the PS_ON signal sent to PIN(10) of connector CN7201
when turning on the power switch and does RL7101 nor-
mally work?
NO
Check the peripheral circuits such as PS_ON circuits of Q7207,
PC7103, RL7101, etc.
YES
Is a DC voltage of approx. 400V applied to both ends of
C7129?
NO Does the PFC circuit normally work?
(Check IC7102, L7103, L7104, D7106, D7108, TH7102, Q7104-5,
Q7117, etc. and the peripheral circuits.)
YES
Is 13V supplied from PIN(1-4) of connector CN7201 when
the power switch is turned on?
NO Check the primary side of T7102-3, Q7111-6, etc., the secondary side
of D7203, etc., the peripheral circuits and the protection circuits of
D7205, D7208, PC7102, etc.
YES
Is 60V supplied when the power switch is turned on?
NO
Check the secondary side of D7201, the protection circuits of D7206,
D7207, D7209, PC7102, etc. and the peripheral circuits.
4 2
The backlight does not light
Are all fluorescent lamps on?
NO
Check each fluorescent lamp, and replace if defective.
(CN7503-12, etc.)

NO
Is F7501 normal?
NO
Check if the peripheral circuits are short-circuited or parts are faulty.
(Q7501, Q7503, etc.)
YES
Is 60V applied to both ends of C7501?
NO
Refer to "No power supply (Front LED does not light up)" and "No
power-up even if turned on (Front LED light up)".
YES
Is a voltage of 13V applied to PIN(20) of IC7501?
NO
Check the 13V line and the peripheral circuits.
YES
Is the STB_ON/OFF signal supplied from PIN(2) of
CN7502?
NO Check the STB signal line on the MAIN_UNIT side and the peripheral
circuits.
(P2303/CN7502, etc.)
YES
Is each control signal of connector CN7502 normally func-
tion?
NO Check each control circuit.
PIN(3) OFL (PWM light control signal input) OFL (PWM light control signal input)/H: Lamp ON, L: Lamp OFF
PIN(5) ERR (Error output) ERR (Error output)/H: Normal, L: Error
PIN(7) REG2 (Light control method identification)
REG2 (Light control method identification)/H: External PWM input, L:
Analog voltage input
PIN(9) ADIM (Tube current setting)
ADIM (Tube current setting)/H: Tube current 12mA, L: Tube current
8.5mA
YES
Is [0] displayed as the number of [LAMP_ERROR] in the
process mode?
NO
Reset the number of [LAMP_ERROR] to the default value in the pro-
cess mode.
YES
Is the drive output signal sent from PIN(16) and (15) of
IC7501?
NO
Check IC7501and the peripheral circuits.
YES
Does the drive output circuit normally work?
NO
Are Q7509-10, Q7501-4, etc. faulty? Check the peripheral circuits.
YES
Does the secondary side of T7501-5 normally work?
NO
Is T7501-5, etc. faulty? Check the peripheral circuits.
YES
Check if the feedback circuit is normal.
(D7501-5, D7507-11, D7513-17, etc.)
4 3
The sound is not emitted from the speaker though the picture has come out.
No sound output in all modes.?
Is the audio signal output of pins (28/L) and (27/R) of
IC3001 (MAIN_MICON) normal?
NO
Check IC3001 and its peripheral circuits.
YES
Is audio signal input to pin(5/L), pin(9/R) of IC2701(AMP)?
NO
Check the line between IC3001 and IC2701.
YES
Is MUTE circuit [MUTE_SP_LINE, RESET_N_LINE] nor-
mal?
NO
Check the MUTE_SP_LINE and RESET_N_LINE.
(Q2701, etc.)
YES
Is the audio signal output of pins (3, 4) (L-ch) and (2, 1)
(R-ch) of P2701(AOUDIO-CONNECTOR) normal?
NO
YES
Check Speaker (right and left) and wire harness.
No sound (during the reception of TV(ANALOG) broadcasting)
Does not the sound go out though the picture has come out when UHF/VHF is received?
Is the SIF signal output from pin (4) of TUNER (TU201)?
NO
Check the tuner and its peripheral circuits.
Replace as required.
YES
Is the SIF signal sent to pins (31) of IC3001
(MAIN_MICON)?
NO
Check the line between TU201 and IC3001.
YES
Refer to No sound output in all modes.
4 4
No sound (during the reception of TV(DIGITAL) broadcasting)
Does not the sound go out though the picture has come out when DTV is received?
Is the audio signal output from PIN(24,25)/ LETFT_M/P,
PIN(28,29)/ RIGH_M/P of IC4001(SET-
TOP_BOX_DECODER).
NO

YES
Is the audio signal input to PIN(6,5)/ LETFT_M/P, (2,3)/
RIGH_M/P of IC4005(OP-AMP)?
NO
YES
Is the audio signal sent from PIN(7)/ AIN1L, (1)/AIN1R of
IC4005 to PIN(10), PIN(9) of IC3001 (MAIN_MICON)?
NO

YES
No sound from external input devices (1)
Does not the sound of the audio signal input to EXT1(SCART1) go out?
Does not the sound of the audio signal input to EXT2(SCART2) go out?
EXT1
Is the audio signal properly sent to pins (6) (AIN3_L) and
(2) (AIN3_R) of SCART1(SC1102)?
NO
Check the setting of an external input device that connects of
SC1102.
EXT2
(2) (AIN2_R) of SCART2(SC1101)?
NO
Check the setting of an external input device that connects of
SC1101.
YES
EXT1
(13) (AIN3_R) of IC3001(MAIN_MICON)?
NO
Check the line between SC1102 and IC3001.
EXT2
(11) (AIN2_R) of IC3001(MAIN_MICON)?
NO
YES
4 5
Does not the sound of the audio signal input to EXT3 go out?
MINI AV UNIT:
Is audio signal output from pin(5/IN3L), (4/IN3R) of input
terminal J1002 to pin(8), (6) of connector SC1001?
NO
Check connection of between from J1002 to SC1001 and the exter-
nal input device.
MAIN UNIT: YES
Is audio signal input to pin(8/IN3L), (6/IN3R) of connector
P1001?
NO
Check the connector(SC1001/ P1001).
YES
Is audio signal input to pin(1/IN3L), (6/IN3R) of IC1301
(AUDIO_SELECTOR)?
NO
Check the line between P1001 and IC1301.
YES
Is the audio signal sent to pin (15/AIN4L), (11/AIN4R) of
IC1301?
NO
YES
Is audio signal input from pin (15/AIN4L), (11/AIN4R) of IC1301 to pin (16, 15) of IC3001 (MAIN_MICON)?
YES NO
Refer to No sound output in all modes Check the line between IC1301 and IC3001.
Does not the sound of the audio signal input to EXT4 go
out?
Does not the sound of the audio signal input to EXT6(Analog) go
out?
Whether "Analog" has selected it in the Audio setup of the HDMI
option is checked.
Is audio signal sent from pin(2/L) and (3/R) of input termi-
nal J1301 to pin(5) and (8) of IC1301
(AUDIO_SELECTOR)?
YES
Is audio signal sent from pin(2/L) and (3/R) of input terminal J1302
to pin(3) and (7) of IC1301(AUDIO_SELECTOR)?
NO NO
Check the connection between J1301 and the peripheral
circuit, the external input devices.
Check the connection between J1302 and the peripheral circuit, the
external input devices.
IC1301?
NO
4 6
YES
YES NO
Does not the sound of the audio signal input to EXT5 go out?
Is audio signal output from pin(2/COMP_AL), (4/
COMP_AR) of input terminal J1303 to pin(13), (9) of
IC1301 (AUDIO_SELECTOR)?
NO
Check connection of between from J1303 to IC1301 and the external
input device.
YES
IC1301?
NO
YES
YES NO
Does not the sound of the audio signal input to EXT6/7(HDMI) go out?
Is picture of the signal input from EXT6/7 displayed?
NO
Refer to Does not the picture of the HDMI signal input to EXT6/7 go
out?.
YES
Is the HDMI_SCK/ WS/ SD0 audio signal output from
pin(86), (85), (84) of IC1951 (HDMI RECEIVER) to pin(39),
(40), (38) of IC3001 (MAIN_MICON)?
NO
Check the line between IC1951 and IC3001, and their peripheral cir-
cuits.
YES
4 7
The audio signal is not output (1)
No audio signal output from SCART1 terminal.
Is audio signal sent to pins (3/L-ch) and (1/R-ch) of
SCART1(SC1102)?
YES
Check the connection to SCART1 and external devices.
NO
Is S-MUTE-LINE [pin(62) of IC2302(SUB_MICON)] at H?
YES
Check the peripheral circuits of IC2302 and S-MUTE_LINE.
(Q1101, etc.)
NO
IC3001(MAIN_MICON)?
YES
(Q1106, Q1105, etc.)
NO
No audio signal output from SCART2 terminal.
SCART2(SC1101)?
YES
Check the connection to SCART2 and external devices.
NO
Is S2-MUTE-LINE [pin(63) of IC2302(SUB_MICON)] at H?
YES
Check the peripheral circuits of IC2302 and S2-MUTE_LINE.
(Q1102, etc.)
NO
IC3001(MAIN_MICON)?
YES
(Q1108, Q1107, etc.)
NO
4 8
NO
No audio signal output from AUDIO_OUTPUT terminal.
Is audio signal output to pin(2/L-ch), (4/R-ch) of audio out-
put terminal J1304?
YES
Check the connection to J1304 and external devices.
NO
Is S-MUTE-LINE [pin(62) of IC2302(SUB_MICON)] at H?
YES
Check the peripheral circuits of IC2302 and S-MUTE_LINE.
(Q1303, etc.)
NO
IC3001(MAIN_MICON)?
YES
Check the line between J1304 and IC3001.
(Q1302, Q1301, etc.)
NO
No sound from HEDPHONE_OUTPUT terminal.
Is the HP_PLUG signal input into pin (208) of
MAIN_UNIT's IC3001 (MAIN_MICON) from pin (6) of a
headphone terminal (J1003)?
NO
Check the line between J1003 and IC3001.
(SC1001/P1001, IC3001, etc.)
YES
Is the audio signal output to pin(2/L-ch) pin(3/R-ch) of
headphone terminal J1003?
YES
Check HEAD-PHONE (J1003) or peripheral circuits.
NO
Is the audio signal input into pin (3) and (1) of connector
SC1001 from pin(3/L-ch),(1/R-ch) of connector P1001?
YES
Check the line between P1001 and J1003.
(SC1001/P1001, etc.)
NO
Is HP-MUTE-LINE [pin(40) of IC2302(SUB_MICON)] at
H?
YES
Check the peripheral circuits of IC2302 and HP-MUTE_LINE.
(Q1001, etc.)
NO
IC3001(MAIN_MICON)?
YES
Check the line between P1001 and IC3001.
(IC1102, etc.)
NO
4 9
No picture on the display (1)
The picture doesn't appear in all modes.
Is the LVDS signal output from IC3001
(MAIN_MICON)?
LVDS0_P/N(140/141), LVDS1_P/N(137/138),
LVDS2_P/N(134/135), LVDS3_P/N(128/129),
LVDS4_P/N(125/126), LVDS_CP/CN(131/132).
NO
Check IC3001 and its peripheral control circuits.
YES
Is the LVDS signal input to IC8103 (LCD_CONTROL)?
A0+/-(165/164), A1+/-(167/166), A2+/-(169/168), A3+/-
(189/188), A4+/-(191/190), ACK+/-(187/186)
NO
YES
Is the control signal of LCD controller normal?
NO Check the control signal R/L_LINE, U/D_OUT_LINE,
FRAME_LINE, BANK_SEL_LINE, TEMP1/2/3_LINE,
QS_EN_LINE, etc.
YES
Is VCC_3.3V, VCC_2.5V or VCC_1.5V supplied to
IC8103?
NO
Check if IC8402(MULTI_CHANNEL_SYSTEM_POWER_SUPPLY)
and the peripheral power supply circuit are normal.
YES
Are the video signals BR/BG/BB (0_P/M-3_P/M), FR/
FG/FB (0_P/M-3_M/P) and the CLK signals (BCLK_P/
M, FCLK_P/M) output from IC8103?
NO
YES
Are BR/BG/BB (0_P/M-3_P/M), BCLK (P/M) input to
connector SC8201 and FR/FG/FB (0_P/M-3_P/M),
FCLK (P/M) input to connector SC8202?
NO
Check the line between IC8103 and SC8201/SC8202.
YES
Are the gradation signals (VH/VL_247, 191, 159, 63,
31, 0) normally sent from IC8201 (GLAY_LEVEL
_GENERATION) to SC8201/SC8202?
NO Check IC8201 and that the communication between its peripheral
circuits and IC8103 is normal. (Each line of DAC_CLK/DATA/
LATCH)
YES
Check the connectors SC8201/SC8202 and LCD panel.
Does not the picture come out when VHF/UHF is received?
Is the video signal(VIN1) output from pin (6) of TUNER
(TU201)?
NO
Check whether I2C is normally accessed between named TU201
and IC3001(MAIN_MICON).
YES
Is the video signal(VIN1) sent to pins (191) of IC3001
(MAIN_MICON)?
NO
Check the line between TU201 and IC3001.
YES
Refer to The picture doesn't appear in all modes.
4 10
Does not the picture come out when DTV is received?
Is the voltage of regulation for a TUNER circuit and the
power supply terminal of IC207 (COFDM) supplied?
(Refer to the circuit diagram)
NO
Each power supply circuit is checked.
YES
Is IF signal output from pin (16),(17) of TUNER(TU201)
to pin(10),(11) of IC207(COFDM)?
NO
Check the tuner, IC207 and their peripheral circuits.
Replace as required.
YES
Similarly, is communication control carried out between
pin (8),(9) of TU201, and pin (20),(21)of IC207?
NO
YES
Does X201(27MHz) oscillate?
NO
Check X201 and its peripheral circuits.
YES
Is the MPEG data (FESCL, FESDA, FEVALID, FES-
TROUT) output from IC207 to IC4001?
NO
Check if the line between IC207 and IC4001 and the control signals
FERROR_LINE and FERESET_LEINE are normal. (IC4402, etc.)
YES
Are the video signals (DTV_R/G/B, DTV_CVBS) output
from PIN(15,16,17), PIN(18) of IC4001?
NO
Check if IC4001, IC4201(SDRAM), IC4251(FLASH_MEMORY) and
IC4202(B+2.5V_REG) are normal.
YES
Are the video signals (DTV_R/G/B, DTV_CVBS) input
to PIN(181,180,179), PIN(184) of IC3001
(MAIN_MICON)?
NO
(IC1401, IC1001, Q1031, etc.)
YES
4 11
[External input EXT1,EXT2] No picture on the display (4)
Does not the picture of the CVBS signal input to EXT1 go out?
Does not the picture of the CVBS signal input to EXT2 go out?
<EXT1>
Is CVBS signal sent to pin (20) of SCART1 (SC1102)?
NO Check the setting of an external input device that connects of SC1102.
<EXT2> NO Check the setting of an external input device that connects of SC1101.
Is CVBS signal sent to pin (20) of SCART2 (SC1101)?
YES
<EXT1>
Is CVBS signal sent to pin (6) of IC1502(SW.)?
NO Check the line between SC1102 and IC1502
<EXT2>
Is CVBS signal sent to pin (4) of IC1502(SW.)?
NO Check the line between SC1101 and IC1502.
YES
Is CVBS signal output to pin(190) of
IC3001(MAIN_MICON) from pin(2) of IC1502?
NO Check the line between IC1502 and IC3001.
(SCART12_LINE, etc.)
YES


Does not the picture of the R/G/B video signal input to EXT1 go out?
Does not the picture of the R/G/B video signal input to EXT2 go out?

<EXT1>
Is RGB1 signal sent to pins (15)/R1, (11)/G1 and (7)/B1
of SCART1(SC1102)?
NO
Check the setting of an external input device that connects of SC1102.
<EXT2>
Is RGB2 signal sent to pins (15)/R2, (11)/G2 and (7)/B2
of SCART2(SC1101)?
NO
Check the setting of an external input device that connects of SC1101.
YES
<EXT1>
Is RGB1 signal sent to pins (187)/R1, (175)/G1 and
(182)/B1 of IC3001(MAIN_MICON)?
NO
<EXT2>
Is RGB2 signal sent to pins (178)/R2, (177)/G2 and
(176)/B2 of IC3001(MAIN_MICON)?
NO
YES
Refer to The picture doesnt appear in all modes.
4 12
Does not the picture of the Y/C video signal input to EXT1 go out?
<EXT1>
Is Y/C video signal sent to pins (20)/Y and (15)/C of
SCART1 (SC1102)?
<EXT2>
Is Y/C video signal sent to pins (20)/Y and (15)/C of
SCART2 (SC1101)?
YES
<EXT1>
Is Y/C signal sent to pins (190)/Y, (187)/C of
IC3001(MAIN_MICON)?
.(IC502, SCART12_LINE, etc.)
<EXT2>
Is Y/C signal sent to pins (190)/Y, (178)/C of
IC3001(MAIN_MICON)?
NO Check the line between SC1101 and IC3001
.(IC502, SCART12_LINE, etc.)
YES
Refer to The picture doesnt appear in all modes.
<When EXT3 is used for external input> No picture on the display (7)
Does not the picture of the composite video signal input to EXT3 go out?
Is CVBS signal output from pin(6) in input terminal
J1002 to pin(10) of connector SC1001?
NO Check the line between J1002 and SC1001.
YES
Is the CVBS signal input from pin(10) of connector
P1001 to pin(1) of IC1001(VIDEO SELECTOR)?
NO Check the line between P1001 and IC1001.
(Connector SC1001/P1001, etc.)
YES
Is CVBS signal output to pin(184) of
(SV1JSW_LINE, EXT_DTV_LINE, etc.)
YES
Refer to (The picture doesn't appear in all modes.)
4 13
Is Y/C signal input into pin(14), (12) of connector
SC1001 from pin(3)/Y, (4)/C of J1001?
NO Check the line between J1001 and SC1001.
YES
Is Y/C signal output from pin(14)/Y,(12)/C of connector
P1001 ?
NO Check the connector SC1001/P1001.
YES
Is the Y/C video signal detection function SV1JSW sig-
nal from pin (6) of the input terminal J1001 normal?
NO Check J1001 or peripheral circuits.
YES
Is the SV1JSW signal input to pin(2) of IC1001
(VIDEO_SELECTOR) and pin(27) of IC2302
(SUB_MICON)?
NO Check the between SV1JSW_LINE J1001 and IC1001/IC2302. (Con-
nector SC1001/P1001, etc.)
YES
Is Y/C signal sent to pins (184), (183) of
IC3001(MAIN_MICON)?
NO Check the line between P1001 and IC3001.
(IC1001, EXT_DTV_LINE etc.)
YES
Does not the picture of the DVI(ANALOG) video signal input to EXT4(15pin-D-SUB terminal) go out?
YES
Are the video signal and the synchronized signal input
from pin(1, 2, 3)/(R, G, B), (13 and 14)/(V, H) of input
terminal D-SUB (SC1201)?
NO Check the connection and setup with the external DVI devices.
YES
Is EDID data pin (6)/SCL, pin(5)/SDA of IC1201
(EEPROM) accessed, and is it read from pin (15),(12)
of a DVI terminal(SC1201)?
NO Is access possible in the re-writing or exchange of EDID data of
IC1201?
YES
NO
Check the circumference circuit of SC1201, IC1201.
Are the video signal and the synchronized signal input
from pin(174, 173, 172)/(R, G, B), pin(171, 47)/(H, V) of
IC3001(MAIN_MICON)?
(IC1941,etc)
YES
4 14
Does not the picture of the component video signal input to EXT5 go out?
Is COMPONENT video signal input into pin(3)/Y, (5)/Pb,
(7)/Pr of the input terminal J1401?
NO Check the connection of J1401 and the external input device.
YES
Is COMPONENT video signal input into pin(1)/Y, (6)/Pb,
(9)/Pr of IC1401(VIDEO_BUFFER)?
NO Check the line between J1401 and IC1401.
YES
Is COMPONENT signal output into pin(180), (179),
(181) of IC3001(MAIN_MICON) from pin(20)/Y, (18)/PB,
(16)/PR of IC1401?
YES
Refer to The picture doesn't appear in all modes
4 15
<When EXT6/7 is used for external input> No picture on the display (11)
Does not the picture of the HDMI signal input to EXT6/7 go out?
EXT6 EXT6
Is the HDMI detection function output from pin (19) of
the HDMI terminal (SC1901) normal?
Check between SC1901and IC3001(MAIN_MICON) of pin(205).
(Q1905, etc.) NO
EXT7 EXT7
Is the HDMI detection function output from pin (19) of
the HDMI terminal (SC1921) normal?
Check between SC1921 and IC3001(MAIN_MICON) of pin(203).
(Q1925, etc.)
YES
Check the connection and setup with the external HDMI devices.
EXT6 NO
Is access possible in the re-writing or exchange of EDID data of
IC1902?
Is EDID data pin (6)/SCL, pin(5)/SDA of
IC1902(EEPROM) accessed, and is it read from pin
(15),(16) of a HDMI terminal(SC1901)?
NO
Check the circumference circuit of SC1901, IC1902 and
IC1951(HDMI_RECEIVER).
EXT7
Is EDID data pin (6)/SCL, pin(5)/SDA of
IC1922(EEPROM) accessed, and is it read from pin
(15),(16) of a HDMI terminal(SC1921)?
NO
Is access possible in the re-writing or exchange of EDID data of
IC1922?
NO
Check the circumference circuit of SC1921, IC1922 and
IC1951(HDMI_RECEIVER).
YES
EXT6
Is TMDS signal input into pin(59,58)/TMDS2_CLKP/N,
(63,62)/TMDS2_D0P/N, (67,66)/TMDS2_D1P/N,
(71,70)/TMDS2_D2P/N of IC1951 from SC1901?
NO
EXT7
Is TMDS signal input into pin(40,39)/TMDS1_CLKP/N,
(44,43)/TMDS1_D0P/N, (48,47)/TMDS1_D1P/N,
(52,51)/TMDS1_D2P/N of IC1951 from SC1921?
NO
YES
Is each signal output from DINR[0:7], DING[0:7],
DINB[0:7], pin(2,3)/HDMI_H/V, (1)/DINEN, (121)/
DINCK, of IC1951?
NO
Is the control signal of IC1951 and IC3001 (MAIN_MICON) normal?
(HDMI_RST, IC1941, etc.)
YES
Is each signal of DINR[0:7], DING[0:7], DINB[0:7], pin(171,47)/HDMI_H/V, (48)/DINEN, (49)/DINCK of IC3001(MAIN_MICON) input?
YES NO
(IC1941, etc.)
4 16
<During external connection> No picture on the monitor (1)
SCART1:
No picture appears on EXT1 - connected monitor during the tuner (U/V) reception.
Checklist:
1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device?... Set it to CVBS, Y/C or RGB.
2) Is ANT-CABLE disconnected or connected improperly? ... Connect it correctly as per the operation manual.
3) The picture is sent to the monitor in a CVBS signal if the source during display is TV, CVBS or Y/C of EXT1-3.
When sent by component, etc., that signal is not sent to the monitor.
4) When the monitor picture is not sent and is not displayed on the monitor, refer to No picture for each terminal.
5) The video output from EXT1 is not the monitor output (output of the picture now watching).
The picture of the last selected TV channel is always sent to EXT1. (Specification)
Is CVBS signal output into pin(19) of SC1102(SCART1)
from pin(2) of IC1102(SW)?
YES Check the setting of an external input device that connects of SC1102.
NO
Is CVBS signal output from PIN(195) of
IC3001(MAIN_MICON) to PIN(6) of IC1102?
YES Check the line between IC1102 and SC1102.
NO
Is video signal (CVBS) sent to pin (195) of IC3001? YES Check power supply of IC3001 and peripheral circuits.
NO
Is VIN1 signal output from pin(6) of TUNRE(TU201)? YES Check the line between TU201 and IC3001.
NO
Check whether I2C is normally accessed between
TU201 and IC3001.
4 17
SCART1:
No picture appears on EXT1 - connected monitor during the tuner (DTV) reception.
Checklist:
1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device? ... Set it to CVBS, Y/C or RGB.
2) Is ANT-CABLE disconnected or connected improperly? ... Connect it correctly as per the operation manual.
Is DTV_CVBS signal output from pin(2) of IC1102(SW)
to pin(19) of SC1102(SCART1)?
NO
Is DTV_CVBS signal output from PIN(195) of
IC3001(MAIN_MICON) to PIN(6) of IC1102?
NO
Is video signal (DTV_CVBS) sent to pin (184) of
IC3001?
YES Check power supply of IC3001 and peripheral circuits.
NO
Is DTV_CVBS signal output from PIN(18) of
IC4001(SET-TOP_BOX_DECODER)?
YES Check the line between IC4001 and IC3001.
(IC1001, EXT_DTV_LINE, etc.)
NO
Check the IC4001 and its peripheral circuits.
4 18
SCART2:
No picture from EXT1 appears on EXT2-connected monitor.
NOTE: Normally, if the screen during display is sent to EXT2, no picture is sent to EXT2.
Checklist:
NO
Is CVBS signal output into pin(194) of
NO
Is video signal (VIN2) from EXT1 sent to pin (190) of
IC3001 (MAIN_MICON)?
YES Check power supply of IC3001 and peripheral circuits.
NO
Is CVBS signal sent to pin (20) of SCART1(SC1102)? YES Check the line between SC1102 and IC3001.
(IC1502, SCART12_LINE, etc.)
NO
Check the setting of an external input device that con-
nects of SC1102.
4 19
SCART2:
No picture from EXT3 appears on EXT2- connected monitor.
Checklist:
NO
Is CVBS signal output into pin(194) of
NO
Is CVBS signal output into pin(194) of IC3001 from
pin(6) of IC1101(VIDEO_SELECTOR)?
YES Check power supply of IC3001 (MAIN_MICON) and peripheral circuits.
NO
Is CVBS signal output into PIN(1) of IC1001 from
PIN(10) of connector P1001?
YES Check IC1001 and its peripheral circuits.
(SV1JSW_LINE, EXTDTV_LINE)
NO
nects of SC1102.
MINI_AV_UNIT: NO
Is the video signal output into PIN(10) of connector
SC1001 from PIN(6) of input terminal J1002?
YES Check the connector SC1001/P1001.
NO
nects of J1002.
5 1
LC32D44E-BK
Service Manual

CHAPTER 5. MAJOR IC INFORMATIONS
[1] MAJOR IC INFORMATIONS
1. IC207 (RH-iXB964WJZZQ)
The STv0362 is a single-chip demodulator using COFDM (coded orthogonal frequency division Multiplexing) and is intended for digital terrestrial
receivers using compressed video, sound and data services. It converts IF or base band differential signals to MPEG-2 format by processing OFDM
carriers.
The STv0362 is fully compliant with the DVB-T specification (ETS 300 744) and Nor Dig Unified specification.
Pin No. Pin Name I/O Pin Function
Clock and resets
32 NOT_RESET I Hardware reset, active low
15 XTAL_I I Analog Crystal oscillator input/external clock (2.5 V)
14 XTAL_O O Analog Crystal oscillator output
13 VDDA_2V5 --- Supply Analog oscillator supply (2.5 V)
16 VDDA_2V5 --- Supply Analog PLL supply (2.5 V)
Analog interface
1 RF_LEVEL --- ADC 8 input for RF level monitoring
2 VDDA_2V5 --- Analog ADC 8 supply (2.5 V)
3 QP --- Positive Q analog input for baseband configuration
4 QM --- Negative Q analog input for baseband configuration
5 VDDA_ISO --- Analog ISO nwell polarization (2.5 V)
6 VDDA_2V5 --- Analog ADC 12 supply (2.5 V)
7 REFP --- Internal positive reference
8 REFM --- Internal negative reference
9 INCM --- Internal common mode
10 IM --- Negative I analog input for IF and baseband configuration
11 IP --- Positive I analog input for IF and baseband configuration
12 VDDA_1.0 --- Analog supply (1.0 V)
I2C interface
29 SDA I/O Serial data (open drain)
30 SCL I Serial clock (open drain)
21 SDAT I/O SDA tuner (open drain)
20 SCLT I SCL tuner
MPEG interface
43 D7 O Serial MPEG data or parallel MPEG data (bit 7)
42 D6 O Parallel MPEG data (bit 6)
44 CLK_OUT O MPEG byte or bit clock
46 STR_OUT O MPEG first byte sync
47 D/NOT_P O MPEG data valid/parity
48 ERROR O MPEG packet error
Front end controls
18 AGC_RF I/O RF AGC control (5 V tolerant)
17 AGC_IF I/O IF AGC control (5 V tolerant)
64 TEST I/O Reserved test mode, must be grounded.
27 GPIO0 I/O General-purpose input/output port 0. Reserved test mode, must be grounded.
49 GPIO1 I/O General-purpose input/output port 1
60 GPIO2 I/O General-purpose input/output port 2 or lock indicator
59 GPIO3 I/O General-purpose input/output port 3 or lock indicator
52 GPIO8 I/O General-purpose input/output port 8. Reserved test mode, must be grounded.
23 AUX_CLK I/O Auxiliary clock
25 CS0 I Chip select LSB
5 2
2. IC1301 (VHINJM2750M-1Y)
The NJM2750 is a 4-input/1-output stereo audio selector. It contains a switch operational amplifier and shows lower noise, lower distortion and higher
channel separation than an ordinary multiplexer or analog switch.
Description:
Operating voltage (4.7 - 13V)
4-input/1-output audio selector
Stereo 2-channel
Low output noise (-110dBV typ.)
Low distortion (0.005% typ.)
3. IC1401 (VHISM5309AV-1Y)
The SM5309A is a 3ch video buffer with a built-in 5th-order low pass filter. The cutoff frequency of the low pass filter can be adjusted between 4MHz
and 40MHz in 256 steps. The low pass filter supports analog inputs/outputs of video signal device of 480i to 1080i format. When it is used as an input
system, it functions as an antialiasing filter of the rear-stage ADC system. If used as an output system, aliasing noise from the video DAC or exoge-
nous noise is eliminated, and the terminating resistance of up to 300 can be driven. The cutoff frequency or signal input method can be controlled by
I2C-BUS.
Description:
Supply voltage: Analog: 4.75 - 5.25V
Digital: 3.0 - 5.5V
Low pass filter function where cutoff frequency can be adjusted in 256 steps
Cutoff frequency range: 4MHz - 40MHz (RISET = 1.8k)
Filter bypath mode function supporting the resolution of SXGA
Switchable to the half fc mode suitable for the component signal (CH-2, CH-3)
2-input multiplexer function (switchable by the I2C-BUS or MUXSEL terminal)
For the video input terminal, the sync-tip clamp/bias/direct input can be selected per channel.
Possible to drive the terminating resistance of up to 300
Output gain: 0dB
Power down function
Consumption current at power down: 1mA or less
Control by I2C-BUS interface
Transfer rate: First mode (400kbit/s) supported
26 CS1 I Chip select MSB
Power supply
19, 24, 31, 38, 45, 51, 55, 62 VDD_1V0 --- Digital core supply (1.0 V)
22, 28, 34, 41, 50, 56, 63 VDD_3V3 --- Digital I/O supply (3.3 V)
1 IN1a I A-ch input selector 1.
2 CNT1 I control 1.
4 CNT2 I control 2.
6 IN1b I B-ch input selector 1.
10 (N.C) --- No connection.
11 OUTb O B-ch output.
12 Vref I Reference voltage.
13 IN3a I Ach input selector 3.
14 V+ --- Power supply.
15 OUTa O A-ch output.
16 GND --- Ground.
1 IN1A I Video signal input terminal (CH-1, A input)
2 IN1B I Video signal input terminal (CH-1, B input)
3 GND --- Ground.
4 ISET --- Resister (RISET) connection terminal for internal current setting.
5 3
4. IC1501 (VHIISL83220-1Y)
+/-15kV ESD Protected, +3V to +5.5V, 1Microamp, 250kbps, RS-232 Transmitters/Receivers.
The ISL83220E is a 3.0V to 5.5V powered RS-232 transmitter/ receiver which meets ElA/TIA-232 and V.28/ V.24 specifications, even at VCC = 3.0V.
Additionally, it provides 15kV ESD protection (IEC 1000-4-2 Air Gap and Human Body Model) on transmitter outputs and receiver inputs (RS-232
pins). Targeted applications are PDAs, Palmtops, and notebook and laptop computers where the low operational, and even lower standby, power
consumption is critical. Efficient on-chip charge pumps, coupled with a manual power down function, reduce the standby supply current to a 1 A
trickle. Small footprint packaging, and the use of small, low value capacitors ensure board space savings as well. Data rates greater than 250kbps are
guaranteed at worst case load conditions. This family is fully compatible with 3.3V only systems, mixed 3.3V and 5.0V systems, and 5.0V only sys-
tems.
5 NC --- No connection.
8 VCC --- Analog power supply.
11 MUXSEL I Input multiplexer select terminal.
12 SCL I I2C clock signal input.
13 SDA I/O I2C data signal in-output.
14 VDD --- Digital power supply.
15 GND --- Ground.
16 OUT3 O Video signal output terminal (CH-3)
19 GND --- Ground.
22 REF2 O Internal reference voltage 2.
23 REF1 O Internal reference voltage 1.
24 ADS I I2C slave address setting terminal (3 states).
1 EN I Active low receiver enable control; doesn't disable ROUTB outputs.
2 C1+ --- External capacitor (voltage doubler) is connected to this lead.
3 V+ --- Internally generated positive transmitter supply.
4 C1- --- External capacitor (voltage doubler) is connected to this lead.
5 C2+ --- External capacitor (voltage inverter) is connected to this lead.
6 C2- --- External capacitor (voltage inverter) is connected to this lead.
7 V- --- Internally generated negative transmitter supply.
8 RIN I 15kV ESD Protected, RS-232 compatible receiver inputs.
9 ROUT O TTL/CMOS level receiver outputs.
10 N.C. --- No connection.
11 TIN I TTL/CMOS compatible transmitter Inputs.
12 N.C. --- No connection.
13 TOUT O 15kV ESD Protected, RS-232 level transmitter outputs.
14 GND --- Ground.
15 VCC --- System power supply input.
16 SHDN I
Active low input shuts down transmitters and on-board power supply, to place device in low power
mode.
5 4
5. IC1702/1735/1745 (VHILV5805M+-1Y)
Step-down DC-DC converter
This is a 1ch step-down switching regulator. It incorporates 0.2FET on the upper side and realizes high-efficiency operation for large output current.
Since the current mode control method is adopted, good load current response and easy phase compensation are available.
The standby mode can be entered using the ON/OFF terminal. The load device is protected by the pulse-by-pulse or current protection and overheat
protection function. Soft start becomes possible by applying capacitance to the soft start terminal.
6. IC1951 (VHiSii9025+-1Q)
The Sii9025 is a compliant with the latest HDMI 1.2 (High Definition Multimedia Interface) specification.
Backward compatibility with DVI 1.0 allows HDMI systems to connect to existing DVI 1.0 hosts.
The SiI9025 is capable of receiving and outputting two channel digital audio at up to 192 kHz- an excellent solution for Digital TVs.
An S/PDIF port supports up to 192 kHz audio.
The SiI9025 also comes pre-programmed with HDCP keys, greatly simplifying the manufacturing process, while providing the highest level of HDCP
key security.
Description:
Dual-Input HDMI 1.2, HDCP 1.1 and DVI 1.0 compliant receiver.
Integrated TMDSR core.
Digital video interface supports video processors:
24-bit RGB/YCbCr 4:4:4
16/20/24-bit YCbCr 4:2:2
8/10/12-bit YCbCr 4:2:2 (ITU BT.656)
12-bit DMO (Digital Multimedia Output) RGB/YCbCr 4:4:4 (clocked with rising & falling edges)
Color Space Conversion for both RGB-to-YCbCr and YCbCr-to-RGB (both 601 and 709)
Auto video mode configuration simplifies system firmware design.
Digital audio interface supports high-end audio systems:
One programmable I2S output for connection to low-cost DACs at 32-192kHz.
S/PDIF output supports PCM, Dolby Digital, DTS digital audio transmission (32-192kHz Fs) using IEC60958 and IEC61937.
Auto audio error detection with programmable soft mute.
Integrated HDCP decryption engine for receiving protected audio and video content.
1 BOOT --- Upper part MOS transistor boot strap capacity connection terminal.
2 VIN I Power voltage supply terminal.
3 SW O Power Switch terminal.
4 GND --- Ground.
5 FB I Feedback terminal.
6 COMP --- Phase amends terminal.
7 EN I Enable terminal.
8 SS I Soft start terminal.
5 5
HDCP Built in Self Test (BIST) lowers cost to test HDCP operation.
Pre-programmed HDCP keys provide highest level of key security, simplifies manufacturing.
Digital Video Output Pins.
144, 143, 142, 141, 140, 137, 136, 133, 132, 131,
130, 129, 126, 125, 124, 123, 119, 118, 117, 116,
113, 112, 111, 110
Q0-23 O 24-bit Output Pixel Data Bus.
1 DE O Data enable.
2 HSYNC O Horizontal Sync Output control signal.
3 VSYNC O Vertical Sync Output control signal.
121 ODCK O Output Data Clock.
Digital Audio Output Pins.
97 XTALIN I Crystal Clock Input.
96 XTALOUT O Crystal Clock Output.
88 MCLKOUT O Audio Master Clock Output.
86 SCK O I2S Serial Clock Output.
85 WS O I2S Word Select Output.
84 SD0 O I2S Serial Data Output.
78 SPDIF O S/PDIF Audio Output.
77 MUTEOUT O Mute Audio Output.
Configuration/Programming Pins.
104 INT O Interrupt Output.
102 RESET# I Reset Pin. Active LOW. 5V Tolerant.
32 DSCL0 I DDCI2C Clock for Port 0. 5V Tolerant.
31 DSDA0 I/O DDCI2C Data for Port 0. 5V Tolerant.
30 DSCL0 I DDCI2C Clock for Port 1. 5V Tolerant.
29 DSDA1 I/O DDCI2C Data for Port 1. 5V Tolerant.
28 CSCL I Configuration I2C Clock. 5V Tolerant.
27 CSDA I/O Configuration I2C Data. 5V Tolerant.
103 SCDT O Indicates active video at HDMI input port.
107 CLK48B I/O Data Bus Latch Enable.
34 R0PWR5V I Port 0 Transmitter Detect. 5V Tolerant.
33 R1PWR5V I Port 1 Transmitter Detect. 5V Tolerant.
101 RSVDL I Reserved, must be tied LOW.
56 RSVD_A Reserved Pin, leave unconnected.
6, 7, 8, 10, 11, 12, 13, 14, 17, 18, 19, 20, 81, 82,
83, 87, 93, 100
NC --- No internal connection.
9 EVNODD O
Indicates. Even or Odd field for interlaced formats. Polarity pro-
grammable in register.
Differential Signal Data Pins.
40 R0XC+ I
HDMI Port 0. TMDS input clock pair.
39 R0XC- I
44 R0X0+ I
HDMI Port 0. TMDS input data pair.
43 R0X0- I
48 R0X1+ I
47 R0X1- I
52 R0X2+ I
51 R0X2- I
59 R1XC+ I
HDMI Port 1. TMDS input clock pair.
58 R1XC- I
63 R1X0+ I
62 R1X0- I
67 R1X1+ I
66 R1X1- I
71 R1X2+ I
70 R1X2- I
Power and Ground Pins.
22, 23, 35, 74, 79, 92, 105, 114, 128, 139 CVCC18 --- Digital Logic VCC.
21, 24, 36, 73, 80, 91, 106, 115, 127, 138 CGND --- Digital Logic GND.
5, 16, 26, 76, 89, 109, 122, 134 IOVCC --- Input/Output Pin Supply(3.3V).
4, 15, 25, 75, 90, 108, 120, 135 IOGND --- Input/Output Pin Ground.
38, 42, 46, 50, 57, 61, 65, 69 AVCC --- TMDS Analog VCC.
41, 45, 49, 53, 60, 64, 68, 72 AGND --- TMDS Analog GND.
37 PVCC0 --- TMDS Port 0 PLL VCC.
55 PVCC1 --- TMDS Port 1 PLL VCC.
5 6
7. IC2302 (RH-IXC009WJZZQ)
The RH-IXC009WJZZQ is a high-speed and high-performance 8-bit single-chip microcomputer with a built-in 61440-byte flash memory.
In this equipment, the R/C LED on the AVC side and system on the display side are controlled.
54 TMDSPGND --- TMDS PLL GND.
94 AUDPVCC18 --- ACR PLL VCC.
95 AUDPGND --- ACR PLL GND.
98 XTALVCC --- ACR PLL Crystal Input VCC.
99 REGVCC --- ACR PLL Regulator VCC.
1 GND --- Ground.
2 8MHz_IN I Crystal oscillator input.
3 8MHz_OUT O Crystal oscillator output.
4 TEST I Terminal for shipping test. Fixed to L level.
5 3.3V --- Power supply (+3.3V).
6 FRC_BUS_SW O N.C.
7 32kHz_OUT O N.C.
8 RESET I RESET input terminal.
9 P20 --- N.C.
10 P00 --- N.C.
11 UART-RXD1 I For flash write.
12 UART-TXD1 O For flash write.
13 CEC-IN I CEC.
14 P04 I N.C.
15 P05 O N.C.
16 CEC-OUT O N.C.
17 CEC-IN2 I N.C.
18 VAREF --- Power supply (+3.3V).
19 AVDD --- Power supply (+3.3V).
20 AIN0 I Temperature sensor.
21 AIN1 I N.C.
5 7
22 AIN2 I N.C.
23 AIN3 I N.C.
24 AC_DET I Power supply detection.
25 ANT_ERR I ANT5V short detection.
26 BL_ERR I Backlight detection.
27 SV1JSW I S-terminal detection.
28 QS_EN O Panel controller QS.
29 FRAME O 50/60Hz select.
30 T1 I Panel controller TEMP.
33 BANK_SEL O Panel controller
34 R/L O Panel controller. Flip horizontal.
35 U/D O Panel controller. Flip vertical.
36 EXT_DTV O DTV_etc. select (H,V,Audio)
37 HDMI_PC O HDMI-PC select (H,V,Audio)
38 SCART12 O SCARTselect.
39 PE O Panel enable.
40 HP_MUTE O Mute. Headphono.
41 ANT+5V_SW O ANT+5V control
42 DTN_BUS_SEL O D-TUNER I2C select
43 DTM_RST O DTV PWB reset
44 TCON_WP O Counter adjustment write-protect
45 LVDS_EN O N.C
46 CONT_DET --- N.C
47 PS_ON O Power_on.
48 PCON1 O DC-DC_on.
49 TEST O N.C
50 LCD_POW O N.C
51 12V_DET O LCD_12V detection.
52 SCL I I2C Slave clock
53 SDA I/O I2C Slave data
54 I-REQ O Sub-microprocessor interrupt
55 SCL_F I N.C. (Pull-up)
56 SDA_F I/O N.C. (Pull-up)
57 LEDPOW_R O Power R_LED ON.
58 LEDPOW_G O Power G_LED ON.
59 LEDSLP O N.C.
60 LEDOPC O N.C.
61 MUTE_SP O Mute.
62 S_MUTE O Mute.
63 S2_MUTE O Mute SCART2.
64 IREM_SW O N.C.
5 8
8. IC2701 (VHiYDA147SZ-1Y)
High-efficiency digital audio power amplifier IC with maximum power output of 20W (Vddp=14V, RL=4) x 2ch.
It incorporates the DRC (Dynamic range compression) function. Since the volume is increased at low volume level and is decreased at high volume
level, it is possible to prevent sudden volume change. It is also provided with the power limiter which can set the output limit.
1, 2, 12, 25, 35, 36 NC --- No connection.
3 PVDDREG --- Power terminal for regulator (PVDD).
4 AVDD --- Output terminal for 3.3V regulator.
5 INLP I Analog input terminal (Lch+)
6 INLM I Analog input terminal (Lch-)
7 VREF VREF terminal.
8 INRM I Analog input terminal (Rch-)
9 INRP I Analog input terminal (Rch+)
10 AVSS --- GND terminal for analog.
11 PLIMIT I Power limit setting terminal.
13, 14 PVDDPR --- Power terminal for digital amplifier output (Rch+).
15, 16, 17 OUTPR O Digital amplifier output terminal (Rch+).
18, 19 PVSSR --- Ground terminal for digital amplifier output (Rch).
20, 21, 22 OUTMR O Digital amplifier output terminal (Rch-).
23, 24 PVDDMR --- Power terminal for digital amplifier output (Rch-).
26 SLEEPN I Sleep control terminal.
27 PROTN O Error flag output terminal.
28 MUTEN I Mute control terminal.
29 CKOUT O Clock output terminal for synchronization.
30 CKIN I External clock input terminal.
31 NCDRC0 I Non-clip/DRC1/DRC2 mode selection terminal 0.
32 NCDRC1 I Non-clip/DRC1/DRC2 mode selection terminal 1.
33 GAIN0 I GAIN setting terminal 0.
34 GAIN1 I GAIN setting terminal 1.
37, 38 PVDDML --- Power terminal for digital amplifier output (Lch-).
39, 40, 41 OUTML O Digital amplifier output terminal (Lch-).
42, 43 PVSSL --- Ground terminal for digital amplifier output (Lch).
44, 45, 46 OUTPL O Digital amplifier output terminal (Lch+).
47, 48 PVDDPL --- Power terminal for digital amplifier output (Lch+).
5 9
The VCT-Pro front-end video processing unit offers 16 analog video inputs (CVBS/Y/C, RGB/Y Cr Cb) as well as digital interfaces for SDTV and DTV.
Latest 3D+ comb filter generation provides highest performance for PAL/NTSC signals.
A VBI slicer, supporting up to 2000 pages of Teletext completes the analog video front end. 3D-motion-adaptive de-interlacing, temporal noise reduc-
tion and film mode detection are based on a unified memory technology.
Description:
Stereo Decoder Audio Processing.
Video Front-end 3D Comb filter, PC Connectivity.
Motion Adaptive De-interlacing.
Scaling, Display Processing and FPD Control.
Unified Memory for Audio, Video and Text.
Controlling, OSD and Text.
1 P4_6 O TP3008
2 P4_5 O HDMI_WPO Write-protection of HDMI_EEP.
3 P4_4 O HDMI_RSTO HDMI reset.
4 TCLK I JTAG Interface Clock Input (TV Controller)
5 TDO O JTAG Interface Data Output (TV Controller)
6 TDI I JTAG Interface Data Input (TV Controller)
7 TMS I JTAG Interface Mode Select Input (TV Contr.)
8 RESETQ I/O Reset Input/Output.
9 AIN1R I Analog Audio 1 Input, Right.
10 AIN1L I Analog Audio 1 Input, Left.
17 VREFAU --- Reference Voltage, Audio.
18 VSUP8.0AU --- Supply Voltage Analog Audio, 8.0 V.
19 GNDA --- Ground Analog Audio, Platform Ground.
20 SGND --- Analog Signal GND.
21 AOUT2R O Analog Audio 2 Output, Right.
22 AOUT2L O Analog Audio 2 Output, Left.
23 AOUT1R O Analog Audio 1 Output, Right.
24 AOUT1L O Analog Audio 1 Output, Left.
25 HEADPHONER O Analog Headphone Output, Right.
26 HEADPHONEL O Analog Headphone Output, Left.
27 SPEAKERR O Analog Loudspeaker Output, Right.
28 SPEAKERL O Analog Loudspeaker Output, Left.
29 SUBWOOFER TEST I/O TP3001
30 VREFSIF I Reference Voltage, Audio SIF.
31 SIFIN+ I Differential Sound IF Input.
32 SIFIN- I Differential Sound IF Input.
33 VSUP5.0 --- Supply Voltage Analog, 5.0 V.
34 GNDA --- Ground Analog, Platform Ground.
35 GND3.3DIG --- Ground Digital Interfaces.
36 VSUP3.3DIG --- Supply Voltage Digital Interfaces, 3.3 V.
37 SPDIF_OUT O SPDIF Output.
38 I2S_DA_IN I Audio Bus Data Input.
39 I2S_CL I Audio Bus Clock Input.
40 I2S_WS I Audio Bus Word Strobe Input.
41 I2S_DEL_OUT O TP3037
42 I2S_DEL_IN I TP3038
43 I2S_DEL_CL I/O TP3039
44 I2S_DEL_WS I/O TP3040
45 VSUP3.3RAM --- Supply Voltage Ram, 3.3 V.
46 GND3.3RAM --- Ground Ram.
47 DVS I Digital or Analog Video VSYNC HD Input.
48 DEN I Digital Video Enable Input.
49 DCLK I Digital Video Clock Input.
50 DRI7 I Digital Video Red 7 Input.
5 10
57 DRI0 I Digital Video Red 0 Input (LSB).
58 DGI7 I Digital Video Green 7 Input.
65 DGI0 I Digital Video Green 0 Input (LSB).
66 DBI7 I Digital Video Blue 7 Input.
73 DBI0 I Digital Video Blue 0 Input (LSB).
74 GND3.3DRI --- Ground Digital Ram Interface.
75 VSUP3.3DRI --- Supply Voltage Digital Ram Interface, 3.3 V.
76 GND3.3COM --- Ground Common.
77 VSUP3.3COM --- Supply Voltage Common, 3.3V.
78 XTALIN I Analog Crystal Input.
79 XTALOUT O Analog Crystal Output.
80 CLKOUT O Digital 20MHz Clock Output.
81 VSO O TP3059
82 HSO O TP3058
83 SCL I/O I2C Bus Clock Input/Output.
84 SDA I/O I2C Bus Data Input/Output.
85 GND3.3FL --- Ground Flash.
86 VSUP3.3FL --- Supply Voltage Flash, 3.3 V.
87 CADC5 I KEY2 operation key input.
88 CADC6 I KEY1 operation key input.
89 P2_2 I IRIN Remote control input.
90 P2_3 I KEY_PSW Power switch input.
91 P2_4 O V_TXD RS232C TX
92 P2_5 I V_RXD RS232C RX
93 OSDV DBO2_0 I/O TP3042
94 OSDH DBO2_1 I/O TP3041
95 GND3.3IO1 --- Ground Digital Input/Output Port 1
96 VSUP3.3IO1 --- Supply Voltage Input/Output Port 1, 3.3 V
97 OSD_CLK I N.C.
98 OSD_FSW I N.C.
99 OSDHCS1 P3_6 I/O TP3021
100 OSDHCS0 P3_7 I/O TP3020
101 OSDB3 P3_5 I/O TP3019
102 OSDB2 P3_4 I/O TP3018
103 OSDB1 I/O N.C.
104 OSDB0 I/O N.C.
105 OSDG3 P3_3 I/O TP3017
106 OSDG2 P3_2 I/O TP3016
107 OSDG1 I/O N.C.
108 OSDG0 I/O N.C.
109 OSDR3 P3_1 I/O TP3015
110 OSDR2 P3_0 I/O TP3014
111 OSDR1 I/O N.C.
112 OSDR0 I/O N.C.
113 GND3.3IO1 --- Ground Digital.
114 VSUP3.3IO1 --- Supply Voltage Port 1, 3.3 V
5 11
115 PCS5 O TP3045
116 PCS4 O TP3043
117 PCS3 O TP3044
118 PCS2 O TP3034
119 PCS1 O TP3033
120 PCS0 O TP3032
121 PCLK2 O TP3022
122 PCLK1 O TP3031
123 GND1.8DIG --- Ground Digital Core
124 VSUP1.8DIG --- Supply Voltage Digital Core, 1.8 V.
125 LVDSA_4P O TP3030
126 LVDSA_4N O TP3029
127 VSUP3.3LVDS --- Supply Digital Voltage LVDS2 Port, 3.3 V.
128 LVDSA_3P O LVDS Channel 1 bit 3 Positive Output.
129 LVDSA_3N O LVDS Channel 1 bit 3 Negative Output.
130 GND3.3LVDS --- Ground Digital LVDS2, 3.3 V.
131 LVDSA_CLKP O LVDS Channel 1 Clock Positive Output.
132 LVDSA_CLKN O LVDS Channel 1 Clock Negative Output.
133 VSUP3.3LVDS --- Supply Digital Voltage LVDS2, 3.3 V.
142 VSUP1.8LVDS --- Supply Analog Voltage LVDS2, 1.8 V.
143 REXT O LVDS External Resistor 2.
144 GND1.8LVDS --- Ground Analog LVDS2, 1.8 V.
145 LVDSB_3P O TP3028
146 LVDSB_3N O TP3027
148 LVDSBCLKP O TP3026
149 LVDSBCLKN O TP3025
159 CADC4 I IF AGC For AGC adjustment.
160 CADC3 I SLOWSW_1I SLOW SW1 input.
161 CADC2 I SLOWSW_2I SLOW SW2 input.
162 CADC1 I TP3009
163 GND3.3DAC --- Ground DAC.
164 VSUP3.3DAC --- Supply Voltage DAC, 3.3V.
165 PWM3 O ST_RS
166 PWM2 O BL_ON Back-light on.
167 PWM1 O OFL1 Modulated light signal.
168 REV O TP3005
169 VSUP1.8FE --- Supply Voltage Analog Video Frontend, 1.8 V.
171 DHS I Digital Video H-Sync Input.
172 VIN21 I Analog Video 21 B HD Input.
173 VIN20 I Analog Video 20 G HD Input.
174 VIN19 I Analog Video 19 R HD Input.
175 VIN18 I Analog Video 18 Fast Blank 2 Input.
5 12
182 VIN9 I Analog Video 9 Y or B SD Input.
183 VIN8 I Analog Video 8 C or Fast Blank 1 Input.
184 VIN7 I Analog Video 7 Y or G SD Input.
186 GNDA --- Analog Video Frontend, Platform Ground.
187 VIN6 I Analog Video 6 C or R SD Input.
188 VIN5 I Analog Video 5 Y/CVBS Input.
189 VIN3 I Analog Video 3 CVBS Input.
192 VSUP3.3VO --- Supply Voltage Analog Video Output, 3.3 V.
193 VOUT3 O TP3002
194 VOUT2 O Analog CVBS Video 2 Output.
195 VOUT1 O Analog CVBS Video 1 Output.
196 GND3.3IO3 --- Ground Digital Input/Output Port 1.
197 VSUP3.3IO3 --- Supply Voltage Input/Output Port 1, 3.3 V.
198 656I0 P3_0 I DTM_IRQI Interrupt from DTV.
199 656I1 P3_1 I/O AVLINK_1
200 656I2 P3_2 I/O AVLINK_2
201 656I3 P3_3 I/O HDMI_INT_I Interrupt from receiver.
202 656I4 P3_4 I/O HDMI_INT_I Interrupt from receiver.
203 656I5 P3_5 O HOTP_CONT0 HDMI plug detection.
204 656I6 P3_6 I MIC_IREQ Interrupt from microcomputer.
205 656I7 P3_7 O HOTP_CONT1 HDMI plug detection.
206 656CLKI I N.C.
207 656CLKO O N.C.
208 P4_7 I HP_PLG Headphone detection.
5 13
This is a video/ audio signal processing IC (Set-top-box decoder) for digital tuner, incorporates a CPU. In this equipment, it implements GUI process-
ing and video/audio processing for digital tuner, negotiation processing with CI-CARD, etc.
System pins
138 CLK27IN I 27 MHz crystal circuit.
139 CLK27OUT O 27 MHz crystal circuit.
128 AUXCLKOUT O Auxiliary clock for general use.
130 NOT_RESET I System reset.
131 NOT_RSTOUT O Reset out.
FMI pins
89 FMIDATA15 I/O Bidirectional data.
90 FMIDATA14 I/O
91 FMIDATA13 I/O
92 FMIDATA12 I/O
93 FMIDATA11 I/O
94 FMIDATA10 I/O
95 FMIDATA9 I/O
97 FMIDATA8 I/O
98 FMIDATA7 I/O
99 FMIDATA6 I/O
100 FMIDATA5 I/O
103 FMIDATA4 I/O
104 FMIDATA3 I/O
105 FMIDATA2 I/O
106 FMIDATA1 I/O
107 FMIDATA0 I/O
56 FMIADDR23 O Address (8 Mbyte).
57 FMIADDR22 O
58 FMIADDR21 O
59 FMIADDR20 O
60 FMIADDR19 O
61 FMIADDR18 O
62 FMIADDR17 O
63 FMIADDR16 O
64 FMIADDR15 O
65 FMIADDR14 O
66 FMIADDR13 O
69 FMIADDR12 O
70 FMIADDR11 O
71 FMIADDR10 O
73 FMIADDR9 O
74 FMIADDR8 O
75 FMIADDR7 O
76 FMIADDR6 O
77 FMIADDR5 O
78 FMIADDR4 O
79 FMIADDR3 O
80 FMIADDR2 O
81 FMIADDR1 O
52 NOT_FMICSD O Chip select.
51 NOT_FMICSC O
50 NOT_FMICSB O
49 NOT_FMICSA O
88 NOT_FMIOE O Output enable.
86 NOT_FMIBE1 O Byte enable.
87 NOT_FMIBE0 O
85 NOT_FMILBA O Flash device load burst address.
83 FMIRDNOTWR O Read not write.
82 FMIWAIT I Wait input (extend read/write cycle).
53 FMIFLASHCLK O Peripheral clock.
LMI pins
5 14
201 LMIDATA15 I/O Bidirectional data.
199 LMIDATA14 I/O
198 LMIDATA13 I/O
197 LMIDATA12 I/O
194 LMIDATA11 I/O
192 LMIDATA10 I/O
191 LMIDATA9 I/O
190 LMIDATA8 I/O
180 LMIDATA7 I/O
178 LMIDATA6 I/O
175 LMIDATA5 I/O
174 LMIDATA4 I/O
171 LMIDATA3 I/O Bidirectional data.
169 LMIDATA2 I/O
168 LMIDATA1 I/O
167 LMIDATA0 I/O
208 LMIADDR12 O Address.
209 LMIADDR11 O
157 LMIADDR10 O
210 LMIADDR9 O
211 LMIADDR8 O
213 LMIADDR7 O
214 LMIADDR6 O
215 LMIADDR5 O
216 LMIADDR4 O
150 LMIADDR3 O
152 LMIADDR2 O
153 LMIADDR1 O
154 LMIADDR0 O
159 LMIBA1 O Bank select.
160 LMIBA0 O
182 LMIDQM0 O Data I/O mask lower.
186 LMIDQM1 O Data I/O mask upper.
181 LMIDQS0 O Data strobe lower.
188 LMIDQS1 O Data strobe upper.
162 NOT_LMICS O Chip select.
163 NOT_LMIRAS O Latch row address strobe.
164 NOT_LMICAS O Latch column address strobe.
206 LMICLKEN O Clock enable.
203 LMICLK O Clock.
202 NOT_LMICLK O Inverted clock.
183 LMI_VREF I Input reference voltage.
166 LMIRDNOTWR O Write enable signal.
Analog audio DAC pins
28 OUTLMINUS O Audio DAC left differential current output.
24 OUTRMINUS O Audio DAC right differential current output.
29 OUTLPLUS O Audio DAC left differential current output.
25 OUTRPLUS O Audio DAC right differential current output.
23 VGBOUT O Audio DAC filtered output reference voltage.
26 IREFADAC I Current reference for Audio DAC.
Digital audio pins
37 S/PDIF O Digital audio.
Analog video DAC pins
15 VDAC1OUT O Video DAC outputs.
16 VDAC2OUT O
17 VDAC3OUT O
18 VDAC4OUT O
14 GNDREXTVDAC I Video DAC external resistor ground.
13 REXTVDACRGB I VDAC external resistor input.
Transport stream pins
35 TS0INBITCLK I TSIN0 Parallel//Serial in.
33 TS0INBITCLKVALI
D
I
34 TS0INPACKETCLK I
36 TS0INDATA7 I
5 15
Programmable I/O pins
127 POI0[7] I/O PIO PORT 0
126 PIO0[6]
123 PIO0[5]
122 PIO0[4]
121 PIO0[3]
120 PIO0[2]
119 PIO0[1]
118 PIO0[0]
46 PIO1[7] I/O PIO PORT 1
45 PIO1[6]
44 PIO1[5]
43 PIO1[4]
41 PIO1[3]
40 PIO1[2]
39 PIO1[1]
38 PIO1[0]
116 PIO2[6]
115 PIO2[5]
114 PIO2[4]
111 PIO2[3]
110 PIO2[2]
109 PIO2[1]
108 PIO2[0]
11 PIO3[5]
10 PIO3[4]
7 PIO3[3]
6 PIO3[2]
5 PIO3[1]
4 PIO3[0]
JTAG test access port (TAP) pins
134 TDI I TAP boundary scan test data input.
133 TMS I TAP boundary scan test mode select.
137 TCK I TAP boundary scan test clock.
135 NOT_TRST I TAP boundary scan test logic reset.
132 TDO O TAP boundary scan test data output.
DCU pins
1 DCUTRIGGERIN I External trigger input to DCU.
2 DCUTRIGGEROUT O Signal to trigger external debug circuitry.
Analog power supply pins (Audio DAC)
32 VDDAADAC --- 3.3v power for audio DAC.
31 GNDAADAC --- Ground for audio DAC.
30 VSSUBANA --- Substrate ground for all DACs.
Analog power supply pins (Video DAC)
22 VDDDAC0 --- 3.3 V power supply for video DAC 1, 2 and 3.
21 VDDDAC1 --- 3.3 V power supply for CVBS video DAC 4.
19 VSSDAC0 --- Ground for video DAC 1, 2 and 3.
20 VSSDAC1 --- Ground for video DAC 4.
Analog power supply pins (Frequency synthesizers)
140 VDDDFS1 --- Frequency synthesizer 1.2 V digital power dedicated to frequency synthesizer 1.
141 GNDDFS1 --- Frequency synthesizer 1.2 V digital ground dedicated to frequency synthesizer 1.
142 VCCAFS --- Frequency synthesizer 1.2 V analog power shared between frequency synthesizer
1 and 2.
143 GNDAFS --- Frequency synthesizer 1.2 V analog ground shared between frequency synthe-
sizer 1 and 2.
144 GNDDFS2 --- Frequency synthesizer 1.2 V digital ground dedicated to frequency synthesizer 2.
145 VDDDFS2 --- Frequency synthesizer 1.2 V digital power dedicated to frequency synthesizer 2.
Analog power supply pins (PLLs)
146 VCCAPLL --- 1.2V PLL1 analog power.
147 GNDAPLL --- 1.2V PLL1 analog ground.
148 GNDAPLL1 --- 1.2V PLL2 analog ground.
149 VCCAPLL1 --- 1.2V PLL2 analog power.
Analog power supply pins (LMI SDRAM)
5 16
11. IC4201 (RH-IXB765WJQZQ)
This IC is 256Mb H-die DDR SDRAM (static dynamic random-access memory) IC.
In this equipment, it is used for LMI memory (for image processing), and data is used for operation of the Set-top-box decoder.
184 VDDDLL --- 1.2 V for DLL.
185 GNDDLL --- Ground for DLL.
176 VDDDE0 --- 1.2 V for delay element 1.
177 VSSDE0 --- Ground for delay element 1.
196 VDDDE1 --- 1.2 V for delay element 2.
195 VSSDE1 --- Ground for delay element 2.
Digital power supply pins
8, 47, 67, 101, 124, 155, 173,
204
VDD12 --- 1.2 V digital power supply.
151, 158, 165, 170, 179, 187,
193, 200, 207, 212
VDD25 --- 2.5 V power supply when connected to DDR SDRAM on the LMI interface.
3, 42, 55, 72, 84, 96, 113, 129 VDD33 --- 3.3 V power supply.
EP1, 9, 27, 48, 54, 68, 102,
112, 125, 136, 156, 161, 172,
189, 205
GND --- Ground.
45, 46 CK, CK I Clock : CK and CK are differential clock inputs.
44 CKE I
Clock Enable : CKE HIGH activates, and CKE LOW deactivates internal clock
signals, and device input buffers and output drivers.
24 CS I
Chip Select : CS enables (registered LOW) and disables (registered HIGH) the
command decoder.
23-21 RAS, CAS, WE I
Command Inputs : RAS, CAS and WE (along with CS) define the command
beingentered.
20, 47 LDM, (UDM) I Input Data Mask.
26, 27 BA0, BA1 I Bank Addres Inputs.
29, 30, 31, 32, 35, 36, 37, 38, 39, 40,
28, 41, 42
A [0:12] I Address Inputs.
2, 4, 5, 7, 8, 10, 11, 13, 54, 56, 57,
59, 60, 62, 63, 65
DQ[0:15] I/O Data Input/Output : Data bus.
16, 51 LDQS, (U)DQS I/O Data Strobe : Output with read data, input with write data.
14, 17, 19, 25, 43, 50, 53 NC --- No Connect : No internal electrical connection is present.
3, 9, 15, 55, 61 VDDQ --- DQ Power Supply.
6, 12, 52, 58, 64 VSSQ --- DQ Ground.
1, 18, 33 VDD --- Power Supply.
34, 48, 66 VSS --- Ground.
49 VREF I SSTL_2 reference voltage.
5 17
5 18
This IC is a high performance CMOS super technology 16Mbit Flash Memory.
Start software (loader) for the CPU with a built-in digital processor and application software have been written on this Flash Memory.
The digital processor reads these soft wares on start-up and implements them.
13. IC4410 (VHIAOZ1320C-1Y)
Load Switch with Controlled Slew Rate IC
25 A0 I Address Inputs.
24 A1 I
23 A2 I
22 A3 I
21 A4 I
20 A5 I
19 A6 I
18 A7 I
8 A8 I
7 A9 I
6 A10 I
5 A11 I
4 A12 I
3 A13 I
2 A14 I
1 A15 I
48 A16 I
17 A17 I
16 A18 I
9 A19 I
29 DQ0 I/O Data inputs/Outputs.
31 DQ1 I/O
33 DQ2 I/O
35 DQ3 I/O
38 DQ4 I/O
40 DQ5 I/O
42 DQ6 I/O
44 DQ7 I/O
30 DQ8 I/O
32 DQ9 I/O
34 DQ10 I/O
36 DQ11 I/O
39 DQ12 I/O
41 DQ13 I/O
43 DQ14 I/O
45 DQ15A-1 I/O Data inputs/Outputs or Address input.
26 E I Chip Enable.
28 G I Output Enable.
11 W I Write Enable.
12 RP I Reset/Block Temporary Unprotect.
15 RB I Ready/Busy Output.
47 BYTE I Byte/Word Organization Select
37 Vcc --- Supply Voltage (3.0V)
27, 46 Vss --- Ground.
10, 13, 14 NC --- Not Connected Internally.
1 OUT O Output. OUT is the source of the P-channel MOSFET.
2 GND --- Ground.
3 EN I Enable. The P-channel MOSFET turns on when EN is logic HIGH.
4 NC --- No Connect. This pin is not internally connected.
5 GND --- Ground.
6 IN I
Input. IN is the drain of the P-channel MOSFET.
It is the supply input of the IC.
5 19
14. IC8103 (VHIT3Z18AFG-1Q)
Single Link LCD Receiver
The LVDS is essentially a signaling method used for high-speed transmission of binary data over copper.
It uses a lower voltage swing than other transmission standards. This low voltage differential is what delivers higher data transmission speeds and
inherently greater bandwidth at lower power consumption.
This new technology not only addresses the needs of todays high performance data transmission application, but also the needs of future applica-
tion.
This LVDS receiver IP supports Single Link transmission between Host and Flat Panel Display. The receiver recovers the LVDS data and converts
into CMOS data. An on-chip PLL synchronizes the received clock with the parallel data and then all are transmitted to the parallel output port of the
receiver.
Description:
Supports Single Link (Single Input to Single Output) up to 135MHz dot clock for SXGA+ (input clock frequency: 25 to 135MHz)
PLL requires no external components
Clock strobe edge selectable
Support 10-bit color
Power down mode
Pin No. Pin Name I/O Function Name Pin No. Pin Name I/O Function Name
1 PLLAVD 1.5V E1AVDLIVC 141 SCLK OUT BT4VIC1
2 PLLAVS GND E1AVSLIVC 142 SDT I/O BD4THVIC1
3 VSSAGND45L GND Z7RSTAGND45L 143 vext1103 1.5V SDRAMVDE1
4 VDDSAVCC4 3.3V Z7RSTAVCC4 144 VDDC 1.5V VDDC
5 VSSAGND45C GND Z7RSTAGND45C 145 RESET IN SMTCIF
6 VDDSAVCC5 3.3V Z7RSTAVCC5 146 CMOS_IN IN IBUFDIF
7 BR0_M OUT Z7RSDST 147 OS_SEL IN TLCHTHDVIC1
8 BR0_P OUT Z7RSDST 148 OS_ON IN TLCHTHDVIC1
9 BR1_M OUT Z7RSDST 149 BANK_SEL IN TLCHTHDVIC1
10 BR1_P OUT Z7RSDST 150 TEMP[2] IN TLCHTHDVIC1
11 BR2_M OUT Z7RSDST 151 vgnd87 GND SDRAMVSE
12 BR2_P OUT Z7RSDST 152 TEMP[1] IN TLCHTHDVIC1
13 BR3_M OUT Z7RSDST 153 TEMP[0] IN TLCHTHDVIC1
14 BR3_P OUT Z7RSDST 154 REV_MODE IN TLCHTHDVIC1
15 BCLK_M OUT Z7RSDST 155 HSCAN IN TLCHTHDVIC1
16 BCLK_P OUT Z7RSDST 156 VSCAN IN TLCHTHDVIC1
17 VDDSAVCC4 3.3V Z7RSTAVCC4 157 vext1105 1.5V SDRAMVDE1
18 VSSDGND1 GND Z7RSTDGND1 158 VSS12 GND VSS12
19 VDDCDVCC1 1.5V Z7RSTDVCC1 159 SELLVDS IN TLCHTHUVIC1
20 VSSAGND45C GND Z7RSTAGND45C 160 SSCLK I/O BD8SCIF
21 VDDSAVCC5 3.3V Z7RSTAVCC5 161 EXCLK IN IBUFIF
22 BG0_M OUT Z7RSDST 162 VDDC 1.5V VDDC
23 BG0_P OUT Z7RSDST 163 VSSAGND1L GND Z7LVRAGND1L
24 BG1_M OUT Z7RSDST 164 RA_M IN Z7LVRXIO
25 BG1_P OUT Z7RSDST 165 RA_P IN Z7LVRXIO
26 BG2_M OUT Z7RSDST 166 RB_M IN Z7LVRXIO
27 BG2_P OUT Z7RSDST 167 RB_P IN Z7LVRXIO
28 BG3_M OUT Z7RSDST 168 RC_M IN Z7LVRXIO
29 BG3_P OUT Z7RSDST 169 RC_P IN Z7LVRXIO
30 VDDSAVCC4 3.3V Z7RSTAVCC4 170 VDDAVDD1L 3.3V Z7LVRAVDD1L
31 VSSDGND1 GND Z7RSTDGND1 171 L_VDDPLL1 2.5V Z7LVRVDDPLL1
32 VDDCDVCC1 1.5V Z7RSTDVCC1 172 L_VSSPLL1 GND Z7LVRVSSPLL1
33 VSSAGND45C GND Z7RSTAGND45C 173 L_VDDPLL2 2.5V Z7LVRVDDPLL2
34 VDDSAVCC5 3.3V Z7RSTAVCC5 174 L_VSSPLL2 GND Z7LVRVSSPLL2
35 BB0_M OUT Z7RSDST 175 L_VDDD 1.5V Z7LVRVDDD
36 BB0_P OUT Z7RSDST 176 L_VSSD GND Z7LVRVSSD
37 BB1_M OUT Z7RSDST 177 PVDDA1B 2.5V Z7LVRVDDPLL1*1
38 BB1_P OUT Z7RSDST 178 PVDDA2B 2.5V Z7LVRVDDPLL2*1
39 BB2_M OUT Z7RSDST 179 VDDS_L 3.3V Z7LVRVDDS
40 BB2_P OUT Z7RSDST 180 PVSSA1B GND Z7LVRVSSPLL1*1
41 BB3_M OUT Z7RSDST 181 PVSSA2B GND Z7LVRVSSPLL2*1
42 BB3_P OUT Z7RSDST 182 VDDC_L 1.5V Z7LVRVDDC
43 VDDCLCDVDDC 1.5V Z7RSTVDDC 183 VDDAVDD2 2.5V Z7LVRAVDD2
44 VSSLCDVSS2 GND Z7RSTVSS2 184 VSSAGND2 GND Z7LVRAGND2
45 VSSAGND45R GND Z7RSTAGND45R 185 VDDAVDD1R 3.3V Z7LVRAVDD1R
5 20
46 vgnd0 GND SDRAMVSE 186 RCLKM IN Z7LVRXIO
47 vext10 1.5V SDRAMVDE1 187 RCLKP IN Z7LVRXIO
48 LS_B OUT B4IF 188 RD_M IN Z7LVRXIO
49 SPB1 OUT BT8IF 189 RD_P IN Z7LVRXIO
50 SPB2 OUT BT8IF 190 RE_M IN Z7LVRXIO
51 VDDS 3.3V VDDS 191 RE_P IN Z7LVRXIO
52 VSS12 GND VSS12 192 VSSAGND1R GND Z7LVRAGND1R
53 REV OUT B4IF 193 VDDC 1.5V VDDC
54 vext12 1.5V SDRAMVDE1 194 CLKOUT OUT Z7DDRVO
55 GOE OUT B4IF 195 VDDS 3.3V VDDS
56 GCK OUT B4IF 196 VCSV1 OUT B4IF
57 GSP1 OUT BT4IF 197 VCSV2 OUT B4IF
58 GSP2 OUT BT4IF 198 VCSV3 OUT B4IF
59 GSLOP OUT B4IF 199 VCSV4 OUT Z7DDRVO
60 VPOL I/O BD4CIF 200 VCSV_Z OUT B4IF
61 VDDC 1.5V VDDC 201 VSS12 GND VSS12
62 VSS12 GND VSS12 202 SPA2 OUT BT8IF
63 ROM256 IN IBUFDIF 203 SPA1 OUT BT8IF
64 MASTER IN IBUFDIF 204 LS_A OUT B4IF
65 vext13 1.5V SDRAMVDE1 205 VDDS 3.3V VDDS
66 vgnd2 GND SDRAMVSE 206 VSSAGND45L GND Z7RSTAGND45L
67 EX_DT[0] I/O BD4CIF 207 VDDCLCDVDDC 1.5V Z7RSTVDDC
68 EX_DT[1] I/O BD4CIF 208 VSSLCDVSS2 GND Z7RSTVSS2
69 vext21 2.5V SDRAMVDE2 209 FR0_M OUT Z7RSDST
70 vgnd3 GND SDRAMVSE 210 FR0_P OUT Z7RSDST
72 vgnd37 GND SDRAMVSE 212 FR1_P OUT Z7RSDST
74 EX_DT[2] I/O BD4CIF 214 FR2_P OUT Z7RSDST
75 VDDS 3.3V VDDS 215 FR3_M OUT Z7RSDST
76 VSS12 GND VSS12 216 FR3_P OUT Z7RSDST
77 EX_DT[3] I/O BD4CIF 217 FCLK_M OUT Z7RSDST
78 EX_DT[4] I/O BD4CIF 218 FCLK_P OUT Z7RSDST
79 EX_DT[5] I/O BD4CIF 219 VDDSAVCC4 3.3V Z7RSTAVCC4
80 EX_DT[6] I/O BD4CIF 220 VSSDGND1 GND Z7RSTDGND1
81 EX_DT[7] I/O BD4CIF 221 VDDCDVCC1 1.5V Z7RSTDVCC1
82 EX_DT[8] I/O BD4CIF 222 VSSAGND45C GND Z7RSTAGND45C
84 EX_DT[10] I/O BD4CIF 224 FG0_M OUT Z7RSDST
85 EX_DT[11] I/O BD4CIF 225 FG0_P OUT Z7RSDST
89 VDDS 3.3V VDDS 229 FG2_P OUT Z7RSDST
90 VSS12 GND VSS12 230 FG3_M OUT Z7RSDST
92 EX_SPIO I/O BD4CIF 232 VDDSAVCC4 3.3V Z7RSTAVCC4
93 VDDC 1.5V VDDC 233 VSSDGND1 GND Z7RSTDGND1
94 VSS12 GND VSS12 234 VDDCDVCC1 1.5V Z7RSTDVCC1
95 EX_CLKI IN IBUFIF 235 VSSAGND45C GND Z7RSTAGND45C
96 EX_CLKO OUT B8IF 236 VDDSAVCC5 3.3V Z7RSTAVCC5
97 EX_DT[16] I/O BD4CIF 237 FB0_M OUT Z7RSDST
98 EX_DT[17] I/O BD4CIF 238 FB0_P OUT Z7RSDST
103 VSS12 GND VSS12 243 FB3_M OUT Z7RSDST
104 VDDS 3.3V VDDS 244 FB3_P OUT Z7RSDST
105 EX_DT[22] I/O BD4CIF 245 VDDCLCDVDDC 1.5V Z7RSTVDDC
106 EX_DT[23] I/O BD4CIF 246 VSSLCDVSS2 GND Z7RSTVSS2
108 EX_DT[25] I/O BD4CIF 248 R_VDDPLL1 2.5V Z7RSTDDRV25
109 EX_DT[26] I/O BD4CIF 249 R_VDDPLL2 2.5V Z7RSTDDRV25
5 21
15. IC8201 (VHIBD8143MU-1Y)
High-accuracy gradation voltage generation IC with a built-in DAC
The high-accuracy gradation voltage generation IC with a built-in DAC, BD8143MUV, has a built-in 1chip integrating the setting value control by the
serial signal, high-accuracy 10bit DAC and buffer amp.
Description:
Reduced number of parts due to 1chip
Built-in 10bit DAC
DAC output buffer amp (12ch)
Amplifier input/output switching function (CTL)
3-wire serial interface
Temperature protection circuit
Power ON reset circuit
110 EX_DT[27] I/O BD4CIF 250 R_VSSPLL1 GND Z7RSTDDRVGND
111 EX_DT[28] I/O BD4CIF 251 R_VSSPLL2 GND Z7RSTDDRVGND
112 VDDC 1.5V VDDC 252 R_VDD15 1.5V Z7RSTDDRV15
113 VSS12 GND VSS12 253 R_VSS15 GND Z7RSTDDRVGND
114 EX_DT[29] I/O BD4CIF 254 VSSAGND45C GND Z7RSTAGND45C
115 vext158 1.5V SDRAMVDE1 255 VDDSAVCC5 3.3V Z7RSTAVCC5
116 VDDS 3.3V VDDS 256 VSSAGND45R GND Z7RSTAGND45R
117 VSS12 GND VSS12
118 vgnd50 GND SDRAMVSE
119 vext26 2.5V SDRAMVDE2
121 EX_DT[30] I/O BD4CIF
122 EX_DIR I/O BD4CIF
123 TEST_C IN IBUFDIF
124 TEST_L[3] IN IBUFDIF
128 vext1102 1.5V SDRAMVDE1
130 DAC_DATA OUT B4IF
131 DAC_CLK OUT B4IF
132 DAC_LATCH OUT B4IF
133 READY OUT B4IF
134 S_LBR OUT B4IF
135 G_LBR OUT B4IF
136 VDDS 3.3V VDDS
137 VSS12 GND VSS12
138 G_LBR_INV OUT B4IF
139 FS OUT B4IF
140 SREADY I/O BD4THVIC1
*Pin No.177, 178 is a power supply for SSCG, Pin No.180, 181 is GND for SSCG, and it is separated with another power supply GND.
1 LATCH I Series latch input.
2 SDIN I Series data input
3 CLK I Series clock input
4 SDOUT O Series data output
5 DVCC --- Logic power supply
6 CT --- Capacity connection terminal for power ON reset.
7 GND --- Ground.
8 N.C --- No Connect.
9 OSC O DAC tune clock I/O.
11 CTL I Amplifier input switch signal input.
12 N.C --- No connection.
13 VCC --- Buffer amplifier power supply.
14 OUT0 O Gradation voltage output terminal 0.
5 22
16. IC8202 (VHIBU55041+-1Y)
Nonvolatile VCOM calibrator
128-gradation current output possible
I2C interface adopted
17. IC8402 (VHIBD8162EK-1Q)
Multi-channel system power supply IC
6-channel output system power supply with a built-in POWER FET
4ch gradation buffer amp + Built-in common amp
20 AGND --- Buffer amplifier ground.
21 AGND --- Buffer amplifier ground.
28 VCC --- Buffer amplifier power supply.
29 REFIN O DAC reference input.
30 VDAC O DAC voltage output.
31 DACGND --- Ground for DAC.
1 IOUT O 128 Step current output terminal.
2 AVDD --- Power supply terminal 2.
3 WPB I
Rewriting protection terminal. Enable at WPB=L
Rewriting is "H" level (VDD).
4 VSS --- Ground terminal.
5 VDD --- Power supply terminal 1.
6 SDA I/O I2C data in-output terminal.
7 SCL I I2C clock terminal.
8 SET --- Maximum current setting terminal.
1 PGND3 --- Ground terminal.
2 PG3 O Power good output 3.
3 DTC3 I Duty control terminal 3.
4 COMP3 O Error margin amplifier output 3.
5 FB3 I Feedback input 3.
6 PVCC3 --- Power supply terminal.
7 LDFB3 I LDO feedback input 3.
8 LDCTL3 I LDO control terminal 3.
9 LDO3 O LDO output 3.
10 IN1 I AMP input 1.
14 IN+ I COM input -.
15 IN- I COM input +.
16 VCOM O COM output.
17 OUT4 O AMP output 4.
21 HGND --- Ground terminal.
22 CPFB2 I Charge pump feedback 2.
23 CPCTL I CP control input.
24 C2 O Charge pump output 2.
5 23
25 VCP2 O Charge pump LOD output 2.
26 HVCC --- Power supply terminal.
27 VCP1 O Charge pump LOD output 1.
28 C1 O Charge pump output 1.
29 CPPG O CP power good output.
30 CPFB1 I Charge pump feedback 1.
31 PGND1 --- Ground terminal.
33 SW1 O Switching output 1.
34 PGATE O P-channel gate drive output.
38 CTL1 I Control input 1.
39 FAULT O Protect detector output.
40 SCP I Short protection delay terminal
41 UVLO I Low voltage lockout setting terminal.
42 VCC --- Power supply terminal.
43 VREF O Reference voltage output terminal.
47 PVCC2 --- Power supply terminal.
48 BOOT2 I Switch boot terminal 2.
52 REG O LDO output for BOOT.
53 LDFB1 I LDO feedback 1.
54 LDCTL1 I LDO control terminal 1.
55 LDPG1 O LDO power good output 1.
57 GND --- Ground terminal.
58 RT I Frequency setting terminal.
59 LDFB2 I LDO feedback 2.
61 LDVCC2 --- Power supply terminal.
64 BOOT3 I Switch boot terminal 3.
6 1
LC32D44E-BK
Service Manual

CHAPTER 6. BLOCK DIAGRAM/OVERALL WIRING
[1] BLOCK DIAGRAM
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
BLOCK DIAGRAM (1/2)
6 2
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
BLOCK DIAGRAM (2/2)
6 3
[2] SYSTEM BLOCK DIAGRAM
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
SYSTEM BLOCK DIAGRAM
6 4
[3] OVERALL WIRING DIAGRAM
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
OVERALL WIRING DIAGRAM
7 1
LC32D44E-BK
Service Manual

CHAPTER 7. PRINTED WIRING BOARD ASSEMBLIES
[1] MAIN Unit
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (Side A)
7 2
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (Chip Side A)
C1118
C1501
C1119
C1502
C8456
C1503
C1504
C1310
R210
R8430
C8458
C1505
C1311
Q1501
R211
C1506
C1312
R8432
R212
C1507
C1313
R8433
R213
C1120
C1314
C1508
R8434
R214
P3081
C1121
C1315
C4001
R8435
R215
C1122
C1316
C4002
R8436
R216
C1123
C1317
C4003
R8437
R217
C1124
C1318
C4004
R218
R8438
C1319
D1101
C1125
C4005
C8461
R8439
R219
C1126
D1102
C4006
C8462
D1103
C1127
C4007
C8463
C1128
D1104
C4008
C8464
C1129
D1105
R1101
FB1201
C4009
C1705
R1102
D1106
FB1202
D1107
R1103
FB1203
C1320
FB1204
D1108
R8440
C8468
R220
R221
C1321
D1109
VA1921
FB1205
C4201
R8441
VA1922
C4202
R222
C1322
R8442
R1107
C4203
VA1923
R223
C1323
R8443
R1108
C4204
C4010
VA1924
C1324
R8444
VA1925
C1131
R1109
C1901
C4011
C4205
D1301
C1325
C3071
R8251
R8445
P3091
C1132
VA1926
C1902
C4206
C4012
D1302
C1326
R226
C3072
R8252
C1133
C4207
C1327
VA1927
D1303
R227
C3073
R8253
D1110
C1134
C4014
C4208
C1328
VA1928
D1304
R228
R8254
C8470
R8448
C1135
D1305
D1111
C4015
Q1901
R1301
C1329
R229
R8255
R8449
C8471
D1306
C1136
D1112
C1906
Q1902
R1302
R8256
C1137
C4017
R1303
Q1903
C8473
D1114
Q1904
R1110
C1138
C4018
R1304
D1115
R1111
C4019
C1139
R1305
C4401
C1715
R1112
D1116
R1306
C4402
R1113
R1307
C1717
C4210
R1308
R230
R8450
D1501
C4211
IC1301
R1309
R231
R8451
C1719
D1502
R232
D1503
R1117
R233
R1118
C4020
C4214
C1140
R234
R8454
R1119
R1501
C1141
C4021
IC3051
R8455
R1502
C1142
C4022
R236
R8456
R1503
R237
C8480
R1504
C4218
C4024
R1310
C1144
R238
C1720
R1505
C4219
R1311
C1145
R239
R8459
C1146
R1312
R1506
R1313
C1147
R1507
R1120
R1314
C1148
C4410
R1508
R1315
C1149
IC1501
R1121
C4029
R4001
C1725 C201
R1122
IC1502
R1316
R4002
C1726
D1702
R1317
R1123
R4003
C1727
C203
R1124
R1318
R240
R8460
C1728
D1705
R1319
R1125
C4221
P2301
FB1031
C4415
C205
C1729
R1126
R4006
C4416
P2302
C206
R1127
R4007
C4223
C4417
R8463
P2303
C207
R1128
R4008
C4224
C4030
R8464 C4419
R1129
C4225
R4009
C4031
C4226
C1922
R1706
C4033
C4227
R8467
R1320
C4034
R1321
C4035
C4229
Q1921
C1155
R8469
IC1701
C1731
R1322
C1156
C4036
Q1922
D1902
IC1702
C4037
Q1923
D1903
R1323
R1130
C4038
Q1924
R1324
C4420
R1131
C4039
R1325
C4421
C211
R1132
R1326
C212
R1133
R1327
C213
C4230
R1134
R1328
R8470
R1329
C4231
R1905
R1135
C215
R8471
R1711
R1136
C4232 IC4202
R1906
C216
R3076
R1712
R8472
R1137
R4017
C4233
C217
R8473
R1138
C4040
R4018
C1161
IC1901
R1139
C4041
C219
C1162
IC1902
C1163
C4043
R1330
R4405
C1741
P2701
C1742
C1743
R1140
C1744
C4049
R4021
R1141
R3081
R1142
R1143
C223
R4218
R1144
R1145
D1725
R1146
C2302
R8482
R4027
R1147
C227
R1148
C228
R8484
C2304
R1149
C229
C2305
C1941
C4052
R1726
R8486
C4053
R8487
C2307
R1727
C2308
L1031
R8489
C1751
Q2305
C1752
R4417
C1753
R4030
C4058
IC4410
C1754
C4059
C1755
IC1725
R1922
C232
C1756
IC1726
R1923
C233
R4034
R1924
C234
C1758
R4035
C4251
R1925
C235
R1731
D1735
R4036
C4252
C236
R4037
C4253
C2313
C4060
C4254
R4038
C238
Q4251
R4039
C4255
IC1921
C2315
C4062
IC1922
C4257
C4063
R4423
C1953
R8498
C4064
C4258
R4424
C1760
C2318
C2319
C2701
R8499
C1761
R4426
C1762
C2702
C1763
C2703
R4040
C240
C2704
C1764
R4041
R4235
IC1735
C1765
C2705
Q2701
Q2702
C2706
C243
C2707
Q2703
C2320
C2708
C245
R1741
C2709
P8101
C2321
D1745
R4046
C246
R1742
R4047
C247
R4430
FL1101
R4431
C249
FL1102
R4432
FL1103
FL1104
R4240
C2710
FL1105
R4435
R4241
C2711
FL1106
R4242
R4436
C2712
FL1107
R4243
R4437
C2713
R2303
FL1108
R4244
R4438
C2714
R2304
R4245
FL1109
C2715
IC1745
R4246
C252
C2716
C253
C2717
C254
C2718
C2719
D1755
R1751
IC2302
D1756
C256
R1752
IC2303
R1753
C257
FL1110
C258
R4441
IC1941
C1971
R1756
C1972
C1973
R1757
R1758
C2720
C1974
R4445
C2721
R2312
C2722
R4447
C2723
C1977
C2724
C2725
IC1755
R1951
D2701
D2702
C2726
R1952
IC1756
D202
R2317
C2727
D2703
R1953
R1954
D2704
C2728
D2705
R1955
C8101
C2729
D2706
R1956
C8102
R1957
IC1951
R1959
R2706
R2707
C2730
R2708
IC2701
C2731
R2709
R4262
C2732
R4263
C2733
R4264
R2324
R1960
C2734
R4265
C271
C2735
R4266
R1962
C2736
R4267
R1963
R2327
C2737
R2710
R1964
R4268
C2738
R1965
R2711
C2739
R2712
R1966
R1967
R2713
R2714
R1968
R2715
R1969
R2716
C1993
R2717
R2718
C2740
R2719
C1995
C2741
R4272
R1970
R1971
L2601
IC201
L2602
R2336
R1973
IC203
R2337
L2603
L2604
R2720
L2605
R2721
IC206
R2722
L2606
IC207
R2723
D8101
R2728
R2729
R8104
R8106
R8108
R2730
IC8101
R2731
R2732
C8132
IC8102
IC8103
C8135
LUG3001
C8136
LUG3002
LUG3003
LUG3004
R8110
LUG3005
LUG3006
R8112
R8114
R8115
R8116
R8501
SC8201
R8502
C8142
SC8202
R8504
R8505
R8507
R8508
R8121
R8122
R8124
C1005
C1006
R8126
C1007
C1008
R8128
C1009
C1201
C1202
C1203 C1204
C1010
R8130
C1011
R8131
C1012
R8132
R8133
R8134
J1301
L8401
R8135
J1302
L8402
R8136
C1017
R8137
L8403
C1018
C1019
C1403
C1405
X3051
C1407
C1409
R8142
R8143
R8145
R8146
R8147
C1410
R8148
FB1101
C1411
R8149
FB1102
FB1103
C1413
FB1104
C1414
FB1105
C1415
FB1106
R1006
C1416
FB1107
C1417
FB1108
D1201
FB1109
IC1001
C1031
D1202
C1032
C1802
D1203
C1033
D1204
C1034
D1205
R1201
FB1301
Q1031
C1035
Q1801
D1206
R1202
FB1302
R1203
D1207
FB1303
D1208
R1204
FB1110
FB1304
R1010
FB1305
FB1111
R1205
D1209
R1011
FB1306
FB1112
R1206
R1207
R1208 R1209
IC1201
FB1309
R1017
FB1501
R1402
FB1502
FB1503
R1403
R1210
R1404
FB4001
IC1401
FL8101
FB4002
FB4003
FB1701
FB1702
L1101
LUG1701
LUG1702
LUG1703
LUG1704
FB4201
D1801
LUG1705
LUG1706
FB4202
D1802
D1803
D1804
R1031
D1805
R1801
R1032
R1802
R1033
R1803
R1034
R1035
R1036
FB4401
FB4402
C2003
FB4403
SC1901
L1701
SC4401
C2019
X2301
C2020
FB1735
X1951
SC1921
FB1745
C2610
FB1941
FL1201
FL1202
FL1203
FB2310
FB4251
FL1401
L1735
FL1402
FL1403
Q203
IC2602 C8201
L1745
C8202
C8203
C8204
C8205
C8206
R2612 R2613
C8207
C8208
R2614
L201
C8209
R2615
C8402
L207
C8210
C8211
C8406
C8212
Q8403
C8213
C8407
C8214
C8408
Q8405
C8215
C8216
C8217
C8218
Q8408
C8219
C8410
C8411
L2701 L2702
C8412
FB8103
L2703
C8413
L2704
C8414
C8415
Q8411
L2705
FB8105
C8222
C8416
L2706
Q8412
Q8413
C8417
C8223
C8418
C8224
Q8414
C8225
C8419
C8226 C8228 C8229
R8202
R8203
C3024
R8204
C8421
R8205
R8206
C8422
R8207
C8423
C8424
R8208
R8209
IC8201
D8401
C8425
IC8202
D8402
C8427
D8403 D8404
C8429
D8405
R3005
D8406
D8407
R3007
D8408
R8210
R3008
IC3001
R8211
D8409
R8212
R8213
R8408
R8214
R8215
C3036
IC8402
R8216
IC8403
R8217
C8433
IC8404
D8410
R8218
R8219
C8436
C8438
R8410
C8439
R8411
L8101 L8102
L8103 L8104 L8105
R8221
L8106
R8222
P4002
C1103
L8107
R8223
C1104
L8108
R8224
C8440
C1105
R8225
L8109
C8441
P1701
C1106
R8226
C1107
C8443
R8227
C1108
R8228
C1109
R8229C8445
C8446
C8447
L8110
C8448
R8420
VA1901
C1301
C8449
L8111
C1302
VA1902
L8112
R8422
C1303
VA1903
R8423
L8113
C1110
C1304
VA1904
R8230
R204
L8114
C1111
Q1301
VA1905
C1305
P3071
R8425
C1112
C1306
VA1906
Q1302
R206
C1113
C1307
VA1907
Q1303
R8233
R8427
C1308
VA1908
R8234
R8428
C3054
C1115
C1309
R8429
C3055
C1116
C8452
C1117
C8453
7 3
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (Side B)
7 4
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (Chip Side B)
R8238
C3058
C8454
Q8450
C3059
C8455
R8239
C8457
C8459
R8431
C3060
R8240
R8241
L263
C8460
Q4001
C1701
Q4002
C1702
Q4003
C1703
Q4004
C1704
C8465
C1706
C8466
C8467
C1707
C1708
C1709
C8469
R224
C1130
R225
IC1101
IC1102
R8446
C1903
C4013
R8447
C1904
C1710
C3074
C1905
C1711
FB1401
C3075
C4016
C8472
C3076
C1712
FB1402
D1113
C1713
R8257
C1907
R8258
C1714
C1908
Q1905
R8259
Q1906
C1716
C8476
D1117
C4403
C8477
C4404
D1118
C1330
C1718
R3054
C8478
C8479
C4405
D1119
C1331
C4406
R3056
R8452
C1332
C4407
Q4403
R8453
C1333
C4408
R8260
R235
C4409 R8261
C3081 C3082
R8262
IC3052
C1143
C4023
R8457
D1120
R8458
C4025
D1121
C1721
C4026
C1722
C4027
C4028
C4411
D1701
C4412
C202
C4413
D1703
R4004
C4414
C204
D1704
R4005
FB1801
R1701
R8461
R8462
R1702
R1703
C4418
C1150
R1704
C208
D4201
IC4001
C1921
C1151
C209
R1705
IC4002
C4032
C1152
R8466
IC4003
C1153
R1707
C4228
IC4004
C1154
R1708
R8468
C1730
IC4005
R4201
D1901
D3071
R1709
R4202
D3072
C1732
R4203
C1157
D3073
IC1703
C1733
R4010
R4204
D1904
C1158
C210
D1905
R1901
R4205
R4011
Q1925
C1159
X201
C1735
R3071
D1906
R4012
R4206
R1902
R3072
C1736
D1907
R4207
R4013
R1903
C1737
R3073
D1908
R4014
R4208
R1904
C214
R3074
C1738
R1710
IC4201
R4209
R4015
D1909
R3075
C1739
R4016
R1907
R1713
C4234
C1160
C218
R1714
R1909
C4235
R4401R4019
R1715
R8475
C4042
R4402
C4236
R1716
R8476
C4237
R4403
R8477
R1717
R4404
R4210
C4044
D1910
R8478
C1740
R1718
R1719
D1911
C4045
R4211
R1331
R8479
R4212
C4046
R1332
R4406
R4407
C4047
R4213
C4048
R4214
R4020
R4408
C220
R4409
R4215
IC4401
R1911
C221
C1745
IC4402
R4216
R4022
R1912
C222
C1746
IC4403
R4023
R4217
C1747
R4024
IC4404
R1914
C224
C1748
R8480
IC4405
R4025
R4219
R1915
C2301
C225
C1749
R8481
IC4406
R4026
C226
R262
D1726
IC4407
C2303
R8483
R4028
C4050
IC4408
R4410
R4029
C4051
IC4409
R4411
R1725
R8485
R4412
R266
R4413
R4220
C4054
R4414
R1728
C1750
D1921
C4055
R4415
R1729
D1922
R4416
C4056
D1923
C4057
R4418
D1924
R1150
C230
R4031
R1921
D1925
R1151
R4419
C231
R3091
R4032
R1152
R3092
R4033
R1153
C1757
R1154
R1730
C2311
R1155
C1759
R8491
R1926
C2312
R1156
R8492
D1736
R1157
C237
R8493
R1928
R4420
C2314
R8494
R4421
C4061
C239
R1735
R8495
C1951
C4256
C1952
R4422
R1736
R8496
C2316
C2317
R8497
R1737
C1954
R1738
R4231
R4425
C1955
R1739
C1956
R4427
C1957
R1930
R4428
C1958
R4429
C241
C1959
R4042
R1932
C242
R4043
R1933
R4044
C244
R1740
R4045
C2322
R283
R1743
C2323
R4048
C248
C1960
D2301
C1961
R1745
R4049
R1746
C1962
R4433
C1963
R1747
R4434
R1748
C1964
R1749
C1965
R2302
C1966
C1967
C250
C1968
C251
C1969
R2305
R2306
R2307
R1750
C255
IC2301
R1754
C1970
R1755
R4443
R4251
C1975
R4252
R4446
C1976
R4253
R2313
R4448
R4254
R2314
C1978
R4255
C1979
D201
R4256R4257 R4258
IC4251
R4259
TH2301
IC4252
TH2302
C8103
IC4253
C1980
R1958
C8104
C269
C8105
C1981
R4452
C1982
C8106
R4453
C1983
C8107
R4260
R4454
C1984
C8108
R2320
R4261
R4455
R2321
C1985
C8109
C1986
C1987
R4458
C1988
R4459
R1961
R2325
C1989
R2326
C8110
R2328
R2329
C8111
R4269
C8112
C8113
C1990
C8114
C8115
C1991
C1992
C8116
C8117
C1994
C8118
C8119
C1996
C1997
C1998
C1999
R2335
IC202
IC204
C8120IC205
C8121
C8122
C8123
C8124
C8125 C8126 C8127
C8128
C8129
R8101
R8102
R8107
C8130
FB3001
C8131
R8109
FB3002
C8133
FB3003
C8134
FB3004
FB3005
FB3006
C8137
C8138
C8139
R8111
R8113
R8117
C8140
R8500
R8118
C8141
C8143
C8144
R8506
R8123
Q1001
R8125
R8127
FB3021
R8129
FB3022
C1013
C1014
C1015
C1016
C1401
C1402
C1404
FB3035
FB3036
C1406
FB3037
C1408
FB3038
R8140
R8141
C1412
X4001
C1801
IC1002
IC261
Q1802
FB3051
R1012
FB3052
R1013
FB3053
R1014
FB3054
R1015
D1401
FB3055
R1016
D1402
FB3056
D1403
R1018
R1019
R1401
R1405
R1020 R1021
R1409
R1022
R1023
FB4004
FB1703
R1410
R1411
FB1901
FB3071
FB1902
FB3072
FB3073
C2000
C2001
C2002
C2004
C2005
Q1831
C2006
C2007
C2008
C2009
C2010
C2011
C2012
C2013
C2014
C2015
C2016
C2017
C2018
C2601
C2602
FB2301
FB2302
FB2304
FB2305
FB2309
FB1951
FB1952
FB1953
FB1954
R2601
FB1955
Q201
FB1956
Q202
R2603
FB1957
Q204
IC2601
C3001
C3002
L203
C3003
L204
C3004
L205
C3005
C8401
L206
C3006
C3007
C8403
C8404
C3008
C3009
C8405
Q8401
Q8402
Q8404
R4561
C8409
C3010
C3011
C3012
C3013
C3014
C3015
FB8101
C3016
FB8102
C3017
C8220
FB8104
Q8410
C3018
C3019
C8221
FB8106
C8227
C3020
C3021
C3022
C3023
C8420
C3025
C3026
C3027
C8230
C3028
C8231
C3029
R3001
C8426
R3002
R3003
R3004
C8428
R8401
R8402
R8403
R8404
C3030
R8405
C3031
C3032
IC3002
R8406
C3033
R8407
C3034
C8430
R8409
IC8401
C3035
C8431
C8432
C3037
C8434
C3038
D8411
C3039
C8435
C8437
FB201
FB202
R8412
R8413
R8414
R8220
C3040
C1101
P4001
R8415
C3041
C1102
C3042
R8416
C3043
R8417
R8418
C3044
Q1101
C3045
R8419
Q1102
C8442
C3046
C3047
C8444
Q1105
Q1106
Q1107
Q1108
R201
R8421
R202
Q262
R203
R8231
C3051
R205
C3052
R8232
C3053
R207
C1114
R208
C8450
C8451
Q3051
R8235
R209
R8236
Q3052
C3056
C3057
7 5
[2] R/C, LED Unit
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
R/C, LED Unit (Side A) R/C, LED Unit (Side B) R/C, LED Unit (Chip Side A) R/C, LED Unit (Chip Side B)
R
1
0
1
R 1 0 8 R 1 0 9
C 1 0 2
R M C 1 0 1
C
1
0
7
D
1
0
1
D
1
0
3
S L D 1 0 1
P
1
0
1
7 6
[3] MINI AV Unit
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MINI AV Unit (Side A)
7 7
[4] KEY
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
S155
R153
D152
S154
S152
R151
D151
S151
R
1
5
2
S153
R
1
5
4
S156
S157
D
1
5
5
P
1
5
1
KEY Unit (Side A) KEY Unit (Chip Parts Side A)
8 1
LC32D44E-BK
Service Manual

CHAPTER 8. SCHEMATIC DIAGRAM
[1] DESCRIPTION OF SCHEMATIC DIAGRAM
1. VOLTAGE MEASUREMENT CONDITION:
1) The voltages at test points are measured on exclusive AC adaptor and the stable supply voltage of AC 120V. Signals are fed by a color bar signal genera-
tor for servicing purpose and the above voltages are measured with a 20k ohm/V tester.
2. INDICATION OF RESISTOR & CAPACITOR:
RESISTOR
1) The unit of resistance "" is omitted.
(K=k=1000, M=M).
2) All resistors are 5%, unless otherwise noted.
(K= 10%, F= 1%, D= 0.5%)
3) All resistors are 1/16W, unless otherwise noted.
CAPACITOR
1) All capacitors are F, unless otherwise noted.
(P=pF=F).
2) All capacitors are 50V, unless otherwise noted.
CAUTION:
This circuit diagram is original one, therefore there may be a slight
difference from yours.
SAFETY NOTES:
1) DISCONNECT THE AC PLUG FROM THE AC OUTLET
BEFORE REPLACING PARTS.
2) SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS
POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS
OPERATING.
IMPORTANT SAFETY NOTICE:
PARTS MARKED WITH " " ( ) ARE IMPORTANT
FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO
REPLACE THESE PARTS WITH SPECIFIED ONES FOR MAIN-
TAINING THE SAFETY AND PERFORMANCE OF THE SET.
AVIS DE SECURITE IMPORTANT:
LES PIECES MARQUEES " " ( ) SONT IMPOR-
TANTES POUR MAINTENIR LA SECURITE DE L'APPAREIL.
NE REMPLACER CES PIEDES QUE PAR DES PIECES DONT LE
NUMERO EST SPECIFIE POUR MAINTENIR LA SECURITE ET
PROTEGER LE BON FONCTIONNEMENT DE L'APPAREIL.
8 2
[2] SCHEMATIC DIAGRAM
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (1/13)
AND SHADED COMPONENTS=SAFETY RELATED PARTS
8 3
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (2/13)
8 4
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (3/13)
8 5
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (4/13)
8 6
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (5/13)
8 7
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (6/13)
8 8
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (7/13)
8 9
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (8/13)
8 10
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (9/13)
8 11
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (10/13)
8 12
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (11/13)
8 13
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (12/13)
8 14
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MAIN Unit (13/13)
8 15
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
R/C, LED Unit
8 16
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
MINI AV Unit
8 17
1 2 3 10 9 7 6 5 4 8
J
A
B
C
D
E
F
G
H
I
13 11 19 18 16 15 14 12 17
KEY Unit
PARTS GUIDE
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
PartsGuide
[1] PRINTED WIRING BOARD
ASSEMBLIES
[2] LCD PANEL
(NOTE: THE PARTS HERE
SHOWN ARE SUPPLIED AS AN
ASSEMBLY BUT NOT
INDEPENDENTLY.)
[3] DUNTKE266FM01(KEY Unit)
[4] DUNTKE449FM02 (MAIN Unit)
[5] DUNTKE457FM02 (R/C, LED Unit)
[6] DUNTKE491FM01(MINI-AV Unit)
[7] CABINET PARTS
[8] LCD MODULE ASSEMBLY
[9] SUPPLIED ACCESSORIES
[10] PACKING PARTS
[11] SERVICE JIGS
CONTENTS
No. S38F8LC32D44E
LCD COLOUR TELEVISION
MODELS LC-32D44E/S/RU-BK/GY
2
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
[1] PRINTED WIRING BOARD ASSEMBLIES
N DUNTKE266FM01 AR N R KEY Unit
N DUNTKE449FM02 CP N R MAIN Unit
N DUNTKE457FM02 AQ N R LED Unit
N DUNTKE491FM01 AY N R MINI-AV Unit
N RUNTKA396WJQZ BV N P POWER/INVERTER Unit
[2] LCD PANEL (NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPEN-
DENTLY.)
N R1LK315T3GW30Y N J 32" LCD Panel Module
[3] DUNTKE266FM01(KEY Unit)
D151 RH-EX0646GEZZY AA J Zener Diode MTZJT-7215B
P151 QPLGNA059WJZZ AC J Plug 5Pin(KM)
R151 VRD-RA2BE822JY AA J Resistor 8.2k 1/8W Carbon
R152 VRD-RA2BE123JY AA J Resistor 12k 1/8W Carbon
R153 VRD-RA2BE822JY AA J Resistor 8.2k 1/8W Carbon
R154 VRD-RA2BE123JY AA J Resistor 12k 1/8W Carbon
S151 QSW-K0003AJZZ+ AB J Switch CH UP
S152 QSW-K0003AJZZ+ AB J Switch CH DOWN
S153 QSW-K0003AJZZ+ AB J Switch CH INPUT
S154 QSW-K0003AJZZ+ AB J Switch VOL UP
S155 QSW-K0003AJZZ+ AB J Switch VOL DOWN
S156 QSW-K0003AJZZ+ AB J Switch CH MENU
S157 QSW-K0003AJZZ+ AB J Switch CH POWER
C201 VCEASX1AN336MY AC J Capacitor 33 10V Electrolytic
C207 VCEASX1CN477MY AE J Capacitor 470 16V Electrolytic
C209 VCKYCZ1EB103KY AA J Capacitor 0.01 25V Ceramic
C215 RC-KZA510WJPZY AB J Capacitor 10 16V Ceramic
C216 VCKYCY1HB104KY AA J Capacitor 0.1 50V Ceramic
C219 VCKYCZ1EF104ZY AA J Capacitor 0.1 25V Ceramic
C230 VCKYCZ1HB102KY AB J Capacitor 1000p 50V Ceramic
C250 VCCCCZ1HH100DY AB J Capacitor 10p 50V Ceramic
C271 VCEASX1CN107MY AC J Capacitor 100 16V Electrolytic
C1009 VCEASX1VN226MY AC J Capacitor 22 35V Electrolytic
C1010 VCEASX1VN226MY AC J Capacitor 22 35V Electrolytic
3
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
C1012 VCEASY1CN476MY AC J Capacitor 47 16V Electrolytic
C1013 VCCCCZ1HH470JY AB J Capacitor 47p 50V Ceramic
C1103 VCKYCY1CB104KY AB J Capacitor 0.1 16V Ceramic
C1127 VCKYCZ1HB221KY AA J Capacitor 220p 50V Ceramic
C1143 VCKYTV1AB105KY AC J Capacitor 1 10V Ceramic
C1201 VCKYCZ1AB104KY AB J Capacitor 0.1 10V Ceramic
4
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
C1332 VCKYTV1CB105KY AC J Capacitor 1 16V Ceramic
C1333 VCKYTV1CB105KY AC J Capacitor 1 16V Ceramic
C1711 VCKYCZ1EB472KY AB J Capacitor 4700p 25V Ceramic
C1715 VCEASY1AN157MY AC J Capacitor 150 10V Electrolytic
C1741 VCEASY1EN107MY AC J Capacitor 100 25V Electrolytic
C1743 RC-KZA383WJZZY AC J Capacitor 10 25V Ceramic
C1744 RC-KZA114WJZZY AB J Capacitor 1 25V Ceramic
C1753 RC-KZA383WJZZY AC J Capacitor 10 25V Ceramic
C1764 VCKYCZ1CF104ZY AA J Capacitor 0.1 16V Ceramic
5
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
C2602 VCKYCY1EB473KY AA J Capacitor 0.047 25V Ceramic
C2701 RC-KZA030WJZZY AB J Capacitor 2.2 10V Ceramic
C2705 VCKYCY1AB105KY AB J Capacitor 1 10V Ceramic
C2719 VCKYTV1EB474KY AC J Capacitor 0.47 25V Ceramic
6
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
C3073 VCCCCZ1HH471JY AA J Capacitor 470p 50V Ceramic
C4002 VCKYCZ0JF105ZY AA J Capacitor 1 6.3V Ceramic
C4008 VCEASY0JN476MY AC J Capacitor 47 6.3V Electrolytic
C4043 VCEASY1CN477MY AD J Capacitor 470 16V Electrolytic
7
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
C4227 VCAAPE0JJ227MY AE J Capacitor 220 6.3V Electrolytic
C4232 VCAAPE0JJ227MY AE J Capacitor 220 6.3V Electrolytic
C4234 RC-KZA578WJQZY N J Capacitor 1 4V Ceramic
C4420 VCAAPD1AJ686MY AE J Capacitor 68 10V Electrolytic
C8102 RC-KZA620WJZZY AA N J Capacitor 0.1 25V Ceramic
8
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
C8203 RC-KZA110WJZZY AD J Capacitor 10 25V Ceramic
C8402 VCKYCY1EB104KY AB J Capacitor 0.1 25V Ceramic
C8410 RC-KZA009WJZZY AB J Capacitor 2.2 6.3V Ceramic
C8422 VCAAPC1CJ226MY AG J Capacitor 22 16V Electrolytic
C8468 VCKYCY1EB473KY AA J Capacitor 0.047 25V Ceramic
9
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
D1101 RH-EXA512WJZZY AB J Zener Diode MAZ8039GHL
D1104 RH-EXA520WJZZY AB J Zener Diode MAZ8051GML
D1118 RH-EXA535WJZZY AM J Zener Diode MAZ8082GML
D1201 VHD1SS226//-1Y AC J Diode 1SS226(T5L F T)
D1208 VHDKDS184//-1Y AB J Diode KDS184-RTK/P
D1501 VHDMA3120WA-1Y AD J Diode MAZ3120D0L
D1503 VHDMA3120WA-1Y AD J Diode MAZ3120D0L
D1701 VHDKDS4148/-1Y AA J Diode KDS4148U-RTK/P
D1702 VHDSMAB33L+-1Y AC J Diode SMAB33L-RTK/P
D1705 VHDD1F60///-1Y AC J Diode D1F60
D1725 VHD1SS390++-1Y AB J Diode 1SS390TE61
D1801 VHD1SS355//-1Y AB J Diode 1SS355TE-17
D1802 RH-EXA526WJZZY AB J Diode MAZ8062GML
D1909 VHDRB520S30-1Y AC J Diode RB520S-30TE61
D8401 VHDRB550EA+-1Y AC J Diode RB550EATR
D8403 VHDMA24D50+-1Y AD J Diode MA24D5000B
D8406 VHDRB160M30-1Y AC J Diode RB160M-30TR
D8408 VHDMA3ZD12+-1Y AC N J Diode MA3ZD1200L
D8410 VHDD1F60///-1Y AC J Diode D1F60
FB201 RBLN-0210TAZZY AB J Ferrite Core
FB1031 RBLN-A188WJZZY AA J Balun BLN-A188WJ
FB1101 RBLN-0077TAZZY AB J Balun BLN-0077TA
FB1202 RBLN-0061TAZZY AD J Balun BLN-0061TA
10
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
FB1701 RBLN-A303WJZZY AB J Balun BLN-A303WJ
FB1901 RBLN-A192WJZZY AA J Ferrite Core
FL1101 RFiLN0017TAZZY AC J Filter
FL1201 RFiLN0003TAZZY AD J Filter
FL8101 RFiLZA007WJZZY AD J Filter
IC202 VHiPQ1M335M-1Y AD J IC PQ1M335M2SPQ
IC203 VHiLV4053FT-1Y AE J IC TC74LVX4053FT(EL)
IC204 VHiBH25FB1G-1Y AD J IC BH25FBIWG-TR
IC205 VHiMM3271AN-1Y J IC MM3271ANRE
IC207 RH-iXB964WJZZQ J IC STV0362
11
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
IC261 VSSSM6J51TU-1Y AF J IC Transistor IC SSM6J51TU
IC1001 VHiNJM2234V-1Y AE J IC NJM2234V(TE1)
IC1002 VHiNJM4558M-1Y AD J IC NJM4558M-TE1
IC1101 VHiMM1506XN-1Y AD J IC MM1506XNRE
IC1201 RH-iXC206WJQZS J IC PC EDID
IC1301 VHiNJM2750M-1Y AH J IC NJM2750M(TE2)
IC1401 VHiSM5309AV-1Y AL J IC SM5309AV-G-ET
IC1501 VHiiSL83220-1Y AQ J IC ISL83220ECVZ-T(S2702)
IC1701 VHiPQ1M335M-1Y AD J IC PQ1M335M2SPQ
IC1702 VHiLV5805M+-1Y AG J IC LV5805M-TE-L-E
IC1703 VHiPST8444N-1Y AC J IC IC-PST8444NR
IC1725 VHiPQ1R50//-1Y AF J IC PQ1R50J0000H
IC1726 VHiPQ20WZ51-1Y AF J IC PQ20WZ5UJ00H
IC1755 VHiPQ012GN1-1Y AF J IC PQ012GN01ZPH
IC1756 VHiPQ1LA185-1Y AD J IC PQ1LA185MSPQ
IC1902 RH-iXC448WJZZS J IC HDMI EDID
IC1922 RH-iXC447WJZZS J IC HDMI EDID
IC1941 VHiTVHC153T-1Y AE J IC TC74VHC153FT(EL,M)
IC1951 VHiSii9025+-1Q AX J IC SII9025CTU
IC2302 RH-iXC009WJZZQ AU J IC 86FS49AUG-6NU2(JZ
IC2701 VHiYDA147SZ-1Y AM J IC YDA147-SZE2
IC3001 RH-iXC354WJZZQ BK N J IC VCT7993P-FA-A1-H000
IC3051 VHiBR24S64M-1Y AF J IC BR24S64FVM-WTR
IC4001 RH-iXC243WJZZQ J IC STI5105ALC
IC4004 VHiLV4052FT-1Y AF J IC TC74LVX4052FT(EL,M)
IC4005 VHiLM833D++-1Y AE J IC LM833DT
IC4201 RH-iXB765WJQZQ AW J IC K4H561638H-UCB3
IC4202 VHiPQ070XNA-1Y AE J IC PQ070XNA1ZPH
IC4251 RH-iXC361WJZZQ N J IC M29W160ET70N6E
IC4252 VHiBR24S64M-1Y AF J IC BR24S64FVM-WTR
IC4401 VHiLCX245FT-1Y AD J IC TC74LCX245FT(EKJ)
IC4402 VHiLCX126FT-1Y AD J IC TC74LCX126FT(EL,K)
IC4403 VHiAHC1G04W-1Y AC J IC 74AHC1G04GW,125
IC4404 VHiLCX16244-1Y N J IC TC74LCX16244(EL,F)
IC4405 VHiLCX16244-1Y N J IC TC74LCX16244(EL,F)
IC4407 VHiTC7SH32U1EY AC J IC TC7SH32FU(TE85L,JF)
IC4409 VHiAHC1G04W-1Y AC J IC 74AHC1G04GW,125
IC4410 VHiAOZ1320C-1Y AE J IC AOZ1320CI-04
IC8101 RH-iXC539WJZZS J IC M24256-BWMN6TP
IC8102 VHiT7WU04FK-1Y AD J IC T7WU04FK
IC8103 VHiT3Z18AFG-1Q BA J IC T3Z18AFG-0003(O2)
IC8201 VHiBD8143MU-1Y AM J IC BD8143MUV-E2
IC8202 VHiBU55041+-1Y AF J IC BU55041HFN-TR-TR
IC8402 VHiBD8162EK-1Q AQ J IC VHIBD8162EK-1Q
J1301 QJAKJ0008GEZZ AD J Jack
J1302 QJAKJ0008GEZZ AD J Jack
J1303 QJAKFA061WJZZ AE J Jack
J1304 QJAKFA061WJZZ AE J Jack
J1401 QJAKGA131WJZZ AG J Jack
L203 VPCNN2R2JR77NY AB J Coil Peaking 2.2H
L263 VPCNN120J1R9NY AB J Coil Peaking 12H
L1031 VPD9M100J1R7NY AC J Coil Peaking 10H
L1101 VPCNN120J1R9NY AB J Coil Peaking 12H
L1701 RCiLPA964WJZZY AD N J Coil 10u
L1735 RCiLPA085WJZZY AD J Coil
L2601 RCiLFA279WJZZY AC J Coil
L2701 RCiLPA899WJZZY AC J Coil Peaking 22H
L8101 RCiLFA122WJZZY AD J Coil
12
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
L8401 RCiLPA962WJZZY AC N J Coil 4.7u
LUG1701 QLUGHA006WJZZY AC J Lug
P1001 QCNCMA012WJZZ AD J Connector 15Pin
P1701 QPLGNA168WJZZY AF J Plug 12Pin(PD)
P2301 QPLGNA325WJZZY AC J Plug 5Pin (RA )
P2302 QPLGNA329WJZZY AD J Plug 9Pin(LB)
P2701 QPLGNA160WJZZY AD J Plug 4Pin(SP)
P3071 QPLGNA324WJZZY AC J Plug 4Pin(KM)
P3081 QPLGN0567FJZZY AD J Plug 5Pin
P4001 QPLGN0463TAZZY AC J Plug, 4Pin(RS)
P4401 QCNCMA313WJSA J Plug
P8101 QPLGN0663TAZZY AD J Plug 6pin
Q202 VSRN4904///-1Y AB J Transistor RN4904
Q203 VS2SC3928AR-1Y AB J Transistor 2SC3928A-T112-1R
Q1001 VSiMH23T110-1Y AC J Transister IMH23T110
Q1105 VS2SA1530AR-1Y AB J Transistor 2SA1530A-T112-1R
Q1501 VSSM3K7002F-1Y AC J Transister SSM3K7002F(5LTST,F
Q1801 VSRDTC144EE-1Y AA J Transister PDTC144EE,115
Q1802 VSDTA124EKA-1Y AB J Transistor DTA124EKAT146
Q1903 VSSSM3K15F+-1Y N J Transister SSM3K15F
Q2701 VSDTC614TK+-1Y AB J Transistor DTC614TKT146
Q8401 VSEMZ1+++++-1Y AC J Transister EMZ1T2R
Q8402 VSDTC114EE/-1Y AB J Transistor DTC114EETL
Q8403 VSTPCP8602+-1Y AD J Transister VSTPCP8602+-1Y
Q8405 VSTPCP8505+-1Y AD J Transister VSTPCP8505+-1Y
Q8408 VS2SD1767++-1Y AD J Transister 2SD1767T100
Q8410 VSRK7002A++-1Y AB J Transister RK7002AT116
Q8450 VSRSS050P03-1Y AG J Transister RSS050P03TB
R204 VRS-CZ1JF000JY AA J Resistor 0 1/16W Metal Oxide
R206 VRK-SA1JF220JY J Resistor 22 1/16W Metal Composition
R209 VRS-CZ1JF102JY AA J Resistor 1k 1/16W Metal Oxide
R211 VRS-CZ1JF392JY AA J Resistor 3.9k 1/16W Metal Oxide
R222 VRK-SA1JF472JY AA J Resistor 4.7k 1/16W Metal Composition
13
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
R239 VRK-SB1FF470JY AA J Resistor 47 1/32W Metal Composition
R1012 VRS-TQ2EF560JY J Resistor 56 1/4W Metal Oxide
R1013 VRS-TQ2EF560JY J Resistor 56 1/4W Metal Oxide
R1014 VRK-SA1JF182JY AC J Resistor 1.8k 1/16W Metal Composition
R1015 VRS-TW2HF820JY AB J Resistor 82 1/2W Metal Oxide
R1021 VRK-SA1JF103JY AB J Resistor 10k 1/16W Metal Composition
R1031 VRS-CZ1JF331FY AA J Resistor 330 1/16W Metal Oxide
R1036 VRS-CZ1JF161FY J Resistor 160 1/16W Metal Oxide
R1101 VRS-CZ1JF153FY AA J Resistor 15k 1/16W Metal Oxide
R1107 VRS-TQ2EF750JY AA J Resistor 75 1/4W Metal Oxide
R1121 VRS-CY1JF000JY AA J Resistor 0 1/16W Metal Oxide
R1131 VRS-TV1JD221JY AA J Resistor 220 1/16W Metal Oxide
R1144 VRK-SA1JF101JY AC J Resistor 100 1/16W Metal Composition
R1147 VRK-SA1JF101JY AC J Resistor 100 1/16W Metal Composition
R1150 VRS-CZ1JF564JY AB J Resistor 560k 1/16W Metal Oxide
R1156 VRK-SA1JF272JY J Resistor 2.7k 1/16W Metal Composition
R1157 VRK-SA1JF272JY J Resistor 2.7k 1/16W Metal Composition
14
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
R1405 VRS-CZ1JF182FY AA J Resistor 1.8k 1/16W Metal Oxide
R1703 VRS-CZ1JF103FY AB J Resistor 10k 1/16W Metal Oxide
R1706 VRS-TW2HF1R0JY AA J Resistor 1 1/2W Metal Oxide
R1725 VRS-CZ1JF222FY AA J Resistor 2.2k 1/16W Metal Oxide
R1726 VRS-TW2HF3R3JY AA J Resistor 3.3 1/2W Metal Oxide
15
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
R1907 VRK-SA1JF474JY J Resistor 470k 1/16W Metal Composition
R1909 VRK-SA1JF473JY AC J Resistor 47k 1/16W Metal Composition
R1912 VRK-SA1JF100JY AB J Resistor 10 1/16W Metal Composition
R1926 VRK-SA1JF474JY J Resistor 470k 1/16W Metal Composition
R1928 VRK-SA1JF473JY AC J Resistor 47k 1/16W Metal Composition
R1930 VRK-SA1JF100JY AB J Resistor 10 1/16W Metal Composition
R1965 VRS-CZ1JF105JY AA J Resistor 1M 1/16W Metal Oxide
R2303 VRK-SB1FF472JY AA J Resistor 4.7k 1/32W Metal Composition
R2706 VRK-SA1JF182JY AC J Resistor 1.8k 1/16W Metal Composition
R2723 VRK-SB1FF224JY J Resistor 220k 1/32W Metal Composition
16
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
R4032 VRK-SB1FF103JY AA J Resistor 10k 1/32W Metal Composition
R4201 VRK-SB1FF820JY J Resistor 82 1/32W Metal Composition
17
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
R8115 VRS-CY1JF105FY AA J Resistor 1M 1/16W Metal Oxide
R8121 VRS-CY1JF331FY AA J Resistor 330 1/16W Metal Oxide
R8142 VRS-CZ1JF101DY AA J Resistor 100 1/16W Metal Oxide
R8210 VRS-CZ1JF752DY AA J Resistor 7.5k 1/16W Metal Oxide
R8213 VRS-CZ1JF243DY AA J Resistor 24k 1/16W Metal Oxide
18
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
R8408 VRS-TW2HPR33JY AA J Resistor 0.33 1/2W Metal Oxide
R8429 VRS-CZ1JF1R0JY AA J Resistor 1 1/16W Metal Oxide
R8432 VRS-CZ1JF1R0JY AA J Resistor 1 1/16W Metal Oxide
R8436 VRS-CY1JF562JY AA J Resistor 5.6k 1/16W Metal Oxide
R8457 VRS-TQ2BD511JY AA J Resistor 510 1/8W Metal Oxide
R8493 VRS-CZ1JF682DY AB J Resistor 6.8k 1/16W Metal Oxide
R8505 VRS-TV1JD3R3JY AA J Resistor 3.3 1/16W Metal Oxide
SC1101 QSOCZA161WJZZ AG J Socket 21Pin (INPUT 2)
SC1102 QSOCZA161WJZZ AG J Socket 21Pin (INPUT 2)
SC1201 QSOCNA770WJZZ AG N J Socket 17Pin (PC-IN(BLACK))
SC1501 QSOCNA769WJZZ AG N J Socket 11Pin (RS232C)
SC1901 QSOCZA171WJZZY AF J Socket 23Pin
SC1921 QSOCZA171WJZZY AF J Socket 23Pin
SC4401 QSOCJA002WJZZQ N J Socket 68Pin
SC8201 QCNCW2367WJZZY AG J Socket 80Pin
SC8202 QCNCW2367WJZZY AG J Socket 80Pin
TH2301 VHHM1103J03-1Y AC J Thermistor
! TU201 RTUDAA019WJQZ BA N P Tuner
X201 RCRSCA039WJZZY AG J Crystal
19
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
X1951 RCRSCA146WJZZY AE J Crystal 28.322MHz
X2301 RCRMCA011WJZZY AD J Crystal
X3051 RCRSC0012CEZZY AH J Crystal 20.25MHz
X4001 RCRSCA039WJZZY AG J Crystal
N NSFTZA243WJFN J Shaft, x4
N PRDARA577WJFW N J Heat Sink
N PSPAZB311WJKZ AE J Spacer
N XBPSN20P10JS0 AD J Screw, x2
[5] DUNTKE457FM02 (R/C, LED Unit)
C102 VCKYTV1CF225ZY AB J Capacitor 2.2 16V Ceramic
D101 RH-EXA092WJZZY AB J Zener Diode UDZSNPTE-1712B
D103 RH-PX0421CEZZY AD J Photo Diode CL-165HR/YG-D-T
P101 QPLGNA339WJZZY AD J Plug 5pin (D)
RMC101 RRMCUA053WJZZ AE J Remote Control
SLD101 PSLDPA076WJFW AD J Shield Case
[6] DUNTKE491FM01(MINI-AV Unit)
C1001 VCKYCY1HB102KY AA J Capacitor 1000p 50V Ceramic
C1046 VCCCCY1HH101JY AA J Capacitor 100p 50V Ceramic
D1001 RH-EXA541WJZZY AB J Zener Diode EXA541WJ
FL1001 RFiLN0080CEZZY AD J Filter FILN0080CE
J1001 QSOCD0456CEZZ AE J Socket
J1002 QJAKGA079WJZZ AD J Jack
J1003 QJAKJ0047CEZZ AD J Jack
LUG1001 QLUGHA002WJZZ AB J Lug
LUG1002 QLUGHA002WJZZ AB J Lug
R1003 VRS-CY1JF102JY AA J Resistor 1k 1/16W Metal Oxide
SC1001 QSOCZ1538CEZZ AE J Socket
20
[7] CABINET PARTS
1
1-1
1-4
1-3
1-2
1-6
1-6
1-7
1-5
1-5
28
21
7
29
4
3
10
17
20
38
13
5
38
38 12
12
11
38
36
36
15
15
9
8
38
36
38
36
38
38
25
14
24
36
36
38
38
33
18
37
37
23
19
30
16
6
3-1
38
11
26
27
22
3-2
35
2-2
40
2
39
2-1
2-7
2-3
2-4
2-3
2-7
2-3
2-7
2-6
2-6
2-3
2-7 2-6
2-4
34
31
21
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
[7] CABINET PARTS
1 CCABAB985WJ01 BG N P Front Cabinet Ass'y (LC-32D44E(BK))
1 CCABAB985WJ02 BM N P Front Cabinet Ass'y (LC-32D44E(GY))
1-1 Not Available - N - Front Cabinet
1-2 Not Available - N - LED Cover
1-3 Not Available - N - Center Dec.
1-4 Not Available - N - SP Sheet
1-5 Not Available - - Mask Himelon, x2 (Top/Bottom)
1-6 Not Available - - Mask Himelon, x2 (Side)
1-7 XEBS930P08000 AA J Screw, x3 (Center Dec.)
2 CCABBB241WJ01 BE N P Rear Cabinet Ass'y
2-1 Not Available - N - Rear Cabinet
2-2 Not Available - N - Terminal Label
2-3 Not Available - N - VESA Holder, x4
2-4 Not Available - N - Molt Plane, x2
2-6 Not Available - N - Himelon, x5
2-7 XEBS930P08000 AA J Screw, x4 (VESA Holder)
3 CCOVAC614WJ01 AM N P MINI AV Cover Ass'y
3-1 Not Available - N - MINI AV Cover
3-2 Not Available - N - Himelon
4 R1LK315T3GW30Y N J 32" LCD Panel Module
5 GCOVAC612WJ1A AH N P Bottom Cover
6 GCOVAC637WJ1A AD N P PC Card Cover
7 JBTN-A718WJ1A AE N P Control Button
8 LANGKB350WJFW AS N P Center Angle (R)
9 LANGKB351WJFW AR N P Center Angle (L)
10 LANGKB358WJFW AW N P Bottom Angle
11 LANGKB359WJFW AD N P LCD Angle A, x2
12 LANGKB397WJFW AD N P LCD Angle B, x2
13 LHLDF1057CEZZ AB J Card Spacer
14 LHLDW1033CE00 AA J Wire Holder
15 LHLDWA143WJKZ AC J Wire Holder, x2 (Cable)
16 LHLDZA933WJKZ AB J MAIN PWB Hplder
17 LHLDZA934WJKZ AB N J POWER PWB Holder
18 PSLDMA403WJZZ AE J Spacer (10*45H), x2
19 PSLDMB358WJFW AK N P Shield
20 PZETKA383WJKZ AG N P Barrier Sheet
21 QCNW-G658WJQZ AG P Connecting Cord (SP)
22 QCNW-G660WJQZ AE N P Connecting Cord (KM)
23 QCNW-G662WJQZ AF N P Connecting Cord (RA)
24 QCNW-G664WJQZ AK N P Connecting Cord (LA)
25 QCNW-G666WJQZ AG N P Connecting Cord (LB)
26 QCNW-H025WJQZ AM J LCD FFC, x2
27 RCORFA064WJZZ AF P Core, x2 (LCD FFC)
28 RSP-ZA321WJZZ AT N J Speaker (L)
29 RSP-ZA322WJZZ AT N J Speaker (R)
! 30 RTUDAA019WJQZ BA N P Tuner
31 TLABNC117WJZZ AB P Model Label
33 XBBS730P04000 AA J Screw (SHIELD)
34 XEBS930P08000 AA J Screw, x2 (TERMINALl)
35 XEBS940P16000 AB J Screw, x6 (CAB-B FIX)
36 XEBSN40P10000 AB J Screw, x6 (LCD-ANG FIX)
37 XHPS730P16WS0 AB N J Screw, x4 (MAIN ETC)
38 XHPS830P06WS0 AA N J Screw,x26 (PWB ETC)
39 XHPS830P10WS0 AB N J Screw,x3 (CAB-B FIX)
40 CDAi-A441WJ02 BF N J Stand Ass'y (LC-32D44E(BK))
40 CDAi-A441WJ05 BG N P Stand Ass'y (LC-32D44E(GY))
22
4-4
4-1
4-2
4-5
4-7
4-8
4-9
4-12
4-17
4-18
4-15
4-13
4-14
4-11
4-10
4-6
4-16
4-3
23
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
4-1 R1LK315T3GW30Y N J LCD Module Ass'y
4-2 CANGKB549WJ01 AS N J Bezel Ass'y (Top)
4-3 CANGKB549WJ02 AR N J Bezel Ass'y (Bottom)
4-4 CANGKB548WJ01 AK N J Bezel Ass'y (L, R), x2
4-5 CHLDZB061WJ01 AT N J Panel Chassis Ass'y (Left)
4-6 CHLDZB062WJ01 AT N J Panel Chassis Ass'y (Right)
4-7 PSHEPA667WJZZ AU N J Lens Sheet, x2
4-8 PSLDK3003TPZZ AY N J Diffusion Panel
4-9 LHLDZA919WJKZ AL N J Lamp Holder-L
4-10 LHLDZA918WJKZ AL N J Lamp Holder-R
4-11 RLMPLA029WJN1 AR N J Lamp Unit, x10
4-12 QSOCFA003WJZZ AD N J Lamp Socket, x10
4-13 RUNTK3923TPZZ AN N J GND PWB (Top)
4-14 RUNTK3924TPZZ AP N J GND PWB (Bottom)
4-15 LHLDZA924WJKZ AB N J Lamp Clip A, x2
4-16 LHLDZA925WJKZ AC N J Lamp Clip B, x2
4-17 PMiR-A166WJZZ AU N J Reflection Sheet
4-18 CCHSMA422WJ01 N J BL Chassis Ass'y
- LX-EZA028WJF9 AB J Screw, x12 (for Bezel, Panel Chassis)
- LX-HZA039WJF7 AB N J Screw, x10 (for Bezel, Panel Chassis, BL Chassis)
X1 LHLDWA173WJKZ AE J Cable Clamp
! X2 QACCKA007WJPZ AK J AC Cord 2Pin (for Europe without U.K. and Ireland.
! X2 QACCBA054WJPZ AQ P AC Cord 3Pin (for U.K. and Ireland)
X3 RRMCGA591WJSA AQ P Remote Control unit (LC-32D44E(BK))
X3 RRMCGA591WJSB AQ P Remote Control unit (LC-32D44E(GY))
X4 TiNS-D477WJZZ AM N P Operation Manual (ENGLISH...) (LC-32D44E(BK)/(GY))
X5 TiNS-D478WJZZ AM N P Operation Manual(SWEDISH...) (LC-32D44E(BK)/(GY))
X6 TiNS-D479WJZZ AP N P Operation Manual(POLISH...) (LC-32D44E(BK)/(GY))
X7 TiNS-D480WJZZ AF N P Operation Manual(RUSSIAN) (LC-32D44E(BK)/(GY))
X8 TGAN-A801WJZZ AB P AQUOS Care Plan (U.K and Ireland)
X9 TGAN-A802WJZZ AC P Warranty Card (U.K and Ireland)
X10 TGAN-A077WJZZ AE J Warranty Card (Russian)
X11 Not Available - - "AA" size Battery
X12 CDAi-A441WJ02 BF N J Stand Ass'y (LC-32D44E(BK))
X12 CDAi-A441WJ05 BG N P Stand Ass'y (LC-32D44E(GY))
X12-1 Not Available - N - Tool for Stand
X3
X11
X4 X5 X6 X7
X8
X9
X10
X2 X1
X12
X12-1
24
[10] PACKING PARTS
S3
S2
S4
S8
S1
S8
S8
S10
S9
S8
S5
S6
S7
S11
S11
25
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PART
DELIVERY
DESCRIPTION
[10] PACKING PARTS
S1 SPAKCD948WJZZ - N - Packing Case
S2 SPAKFB417WJZZ - N - Stand Case
S3 SPAKFB418WJZZ - N - Stand Pad (LC-32D44E(BK))
S3 SPAKFB550WJZZ - N - Stand Pad (LC-32D44E(GY))
S4 SPAKPA382WJZZ - N - Wrapping Paper
S5 SPAKPB053WJZZ - N - Mirror Mat (Stand Support)
S6 SPAKPB054WJZZ - N - Mirror Mat (Stand Bsse)
S7 SPAKAA373WJZZ - N - Cover Sheet
S8 SPAKXB805WJZZ - N - Buffer material (Top/Bottom)
S9 SSAKAA009WJZZ - - Polyethylene bag
S10 SSAKAA111WJZZ - N - Polyethylene bag
S11 TLABM5584BMZZ - - Case No. Label
[11] SERVICE JIGS
N QCNW-G440WJQZ AP N J Connecting Cord (4-5pins L=1000mm), Main to Key
N QCNW-H184WJQZ AX N J Connecting Cord, MAIN-R/C,LED
N QCNW-H185WJQZ AV N J Connecting Cord, MAIN-POWER
N QCNW-H186WJQZ AQ N J Connecting Cord, MAIN-POWER
N QCNW-H187WJQZ AP N J Connecting Cord, MAIN-SPEAKER
N QCNW-C222WJQZ AW J Connecting Cord (80pin FFC L=1000mm), x2 MAIN t

COPYRIGHT 2008 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No Part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any from or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
AV Systems Group
CS Promotion Center
Yaita,Tochigi 329-2193, Japan
Mar. 2008
TQ -S SH. DS

Sharp Lc-32d44e S Ru-Bk Gy - Et

Uploaded by

Copyright:

Available Formats

Sharp Lc-32d44e S Ru-Bk Gy - Et

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sharp Lc-32d44e S Ru-Bk Gy - Et

Uploaded by

Copyright:

Available Formats

SERVICE MANUAL

LC32D44E/S/RU-BK/GY (1st Eddition)

You might also like