DS20930 1

AS
Notice
CORRECTION
PRODUCTION CHANGE
SERVICE FLASH
ADD INFORMATION
FILE NO.
REVISION 07
Please add this notice to the Service Manual listed below.

Category :
COLOR TELEVISION
Model:
DS20930
Date:
April / 15 / 2004
Effective from : Chassis No.
Destination: U.S.A. / CANADA
20930-07
REF : No. SM780088-06
NOTE: Match the Chassis No. on the units back cover with the Chassis No. in the Service
Manual. If the Service Manual Chassis No. does not match the units, additional Service
Literature is required. This chassis is similar to Chassis No. 20930-06. Only the
difference Service Information is given in this manual. For detailed Service Information,
refer to the Original Service Manual and Notices for Chassis No. 20930-06 used in Model
DS20930 (SM780088-06).
1. IN THE CHASSIS ELECTRICAL PARTS LIST
The reason for change.

A : Misprint
B : Quality Reliability
D : Design
E : Add as a possible sub
G : Purchasing Request
C : Standardization
F : Schematic location change
Page &
Section
Schematic
Location
Page 19,
Chassis
Electrical
Parts List
R497
Old
401 068 1600
OXIDE-MT 4.7 JA 2W
1
NO
-------------------------------------------------------------New
401 068 6209
OXIDE-MT 5.6 JA 2W
1
NO
A100
Old
610 310 6847
ASSY, PWB, MAIN
1
NO
-------------------------------------------------------------New
610 312 5824
ASSY, PWB, MAIN
1
NO
A700
Old
610 310 6854
ASSY, PWB, SOCKET
1
YES
-------------------------------------------------------------New
610 312 5831
ASSY, PWB, SOCKET
1
YES
Q901
Old
414 012 3209
CRT A51QDX992X003
1
NO
-------------------------------------------------------------New
414 012 3100
CRT A51QDK190X022
1
NO
Page 20
Chassis
Electrical
Parts List
Part No.
DS20930, G8TDM, PRODUCT CODE 111367880
Description
Qty
Interchangeability
Reason
REFERENCE No. SM780088-07
AS
Notice
CORRECTION
PRODUCTION CHANGE
SERVICE FLASH
ADD INFORMATION
FILE NO.
REVISION 06

Category :
COLOR TELEVISION
Model:
DS20930
Destination:
U.S.A. / CANADA
Date:
APRIL / 15 / 2004

REF : No.
20930-06
SM780088
NOTE: Match the Chassis No. on the units back cover with the Chassis No. in the Service Manual.
If the Service Manual Chassis No. does not match the units, additional Service Literature
is required. This chassis is similar to Chassis No. 20930-00, however, all Service Information
is given in this Notice for Chassis No. 20930-06 used in Model DS20930.
Contents
Specifications
Safety Instructions . . . . . . . . . . . . . . . . . . 2
Service Adjustments . . . . . . . . . . . . . 3 - 10
Service Hints . . . . . . . . . . . . . . . . . . . . . . 11
Mechanical Disassemblies. . . . . . . . . . . 12
Chassis Electrical Parts List . . . . . . 13 - 19
Cabinet Parts List . . . . . . . . . . . . . . . . . . 20
Component and Test Point
Locations . . . . . . . . . . . . . . . . . . . 21 - 24
Schematic Insert . . . . . . . . . . . . . . . 25 - 32
Schematic Notes . . . . . . . . . . . . . . . . . 25
Pin Layouts . . . . . . . . . . . . . . . . . . . . . 25
Capacitor and Resistor Codes . . . . . . 25
Block Diagram . . . . . . . . . . . . . . . 26 - 27
Voltage Charts . . . . . . . . . . . . . . . 26 - 27
Waveforms. . . . . . . . . . . . . . . . . . . . . . 28
Schematic Diagrams . . . . . . . . . . 29 - 32
Power Rating . . . . . . . . . . . . . . . . . . . . . 120V, 60Hz

65W (Avg), 1.4A (Max)
Antenna Input Impedance . . . . . . . . . . . . . . . . . 75
UHF/VHF/CATV
Receiving Channel . . . . . . . . . . . . . . . . 2 - 13 (VHF),
14 - 69 (UHF),
01, 14-94, 95-125 (CATV)
Remote Ready . . . . . . . . . . 24 Key Remote Control
Sound Output . . . . . . . . . . . . . . . . . . . . . . 1.0 W/CH
Intermediate Frequency
Picture IF Carrier . . . . . . . . . . . . . . . . . . 45.75MHz
Sound IF Carrier . . . . . . . . . . . . . . . . . . 41.25MHz
Color Sub Carrier . . . . . . . . . . . . . . . . . 42.17MHz
Picture Tube . . . . . . . . . . . . . . . . . A51QDX992X003
Semiconductors
Integrated Circuits. . . . . . . . . . . . . . . . . . . . . . . . 8
Transistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Except within Tuner and RC Pre-Amp.
Cabinet Dimensions
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 588mm
Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . 466mm
Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 493mm
DS20930, G8TCM, PRODUCT CODE 111367880
SAFETY INSTRUCTIONS
SAFETY PRECAUTIONS
WARNING: The chassis of this receiver has a floating
ground with the potential of one half the AC line voltage in
respect to earth ground. Service should not be attempted by
anyone not familiar with the precautions necessary when
working on this type of equipment.
The following precautions must be observed:
1. An isolation transformer must be connected in the power
line between the receiver and the AC line before any service is performed on the receiver.
READING SHOULD NOT EXCEED 750 mV.

AC VOLTMETER
(5000 ohms per volt or more sensitivity)
TELEVISION
RECEIVER
2. Comply with all caution and safety-related notes provided on the side of the cabinet, inside the cabinet, on the
chassis, and the picture tube.
1500 ohm
10 watt
3. When replacing a chassis in the cabinet, always be certain

that all the protective devices are installed properly, such
as control knobs, adjustment covers, shields and barriers.
DO NOT OPERATE THIS TELEVISION RECEIVER
WITHOUT THE PROTECTIVE SHIELD IN POSITION AND
PROPERLY SECURED.
4. Before replacing the back cover of the set, thoroughly
inspect the inside of the cabinet to see that no stray parts
or tools have been left inside.
Before returning any television to the customer, the
service technician must perform the following safety
checks to be sure that the unit is completely safe to
operate without danger of electrical shock.
ANTENNA COLD CHECK

Remove AC plug from the 120 VAC outlet and place a
jumper across the two blades. Connect one lead of an ohmmeter to the jumpered AC plug, and touch the other lead to
each exposed antenna terminal (UHF and VHF antenna terminals). The resistance must measure between 1M ohm and
5.2M ohm. Any resistance value below or above this range
indicates an abnormality which requires corrective action.
LEAKAGE CURRENT CHECK

Plug the AC line cord directly into a 120 VAC outlet. (Do not
use an isolation transformer for this check.) Use an AC voltmeter, that has 5000 ohms per volt or more sensitivity.
Connect a 1500 ohm 10 watt resistor, paralleled by a 0.15 F
150 VAC capacitor, between a known good earth ground
(water pipe, conduit, etc.) and all exposed metal parts of the
cabinet (antennas, handle bracket, metal cabinet, screw
heads, metal overlays, control shafts, etc.). Measure the AC
voltage across the 1500 ohm resistor. The AC voltage
should not exceed 750 mV. A reading exceeding 750 mV
indicates that a dangerous potential exists. The fault must
be located and corrected. Repeat the above test with the
receiver power plug reversed.
NEVER RETURN A RECEIVER TO THE CUSTOMER
WITHOUT TAKING THE NECESSARY CORRECTIVE ACTION.
Good earth ground

such as a water pipe,
conduit, etc.
0.15 F 150V AC
AC OUTLET
To be touched to all of exposed metal parts.

Voltmeter Hook-up for Leakage Current Check.
X-RADIATION PRECAUTION
The primary source of X-RADIATION in solid-state receivers is
the picture tube. The picture tube is specially constructed to
limit X-Ray emission. For continued X-RADIATION protection,
the replacement tube must be the same type as the original
(including the suffix letter in the part numbers). Excessive high
voltage may produce potentially hazardous X-RADIATION. To
avoid such hazards, the high voltage must be maintained within
specific limits. Refer to the X-RADIATION WARNING NOTE on
the CHASSIS SCHEMATIC in this service manual for specific
high voltage limits. If the high voltage exceeds specified limits,
check the components specified on the chassis schematic
diagram and take the necessary corrective action. Carefully
follow the instructions for the +B Voltage Check and the High
Voltage Check to maintain the high voltage within the specified
limits.
HIGH VOLTAGE HOLD-DOWN TEST

To prevent X-RADIATION from the picture tube due to
excessive high voltage, a HOLD-DOWN circuit is provided in
the high voltage circuit. Every time the receiver is serviced,
the high voltage HOLD-DOWN circuit must be tested for
proper operation. Refer to the HIGH VOLTAGE HOLDDOWN TEST in service adjustments.
PRODUCT SAFETY NOTICE

When replacing components in a receiver, always keep in
mind the necessary product safety precautions. Pay special
attention to the replacement of components marked with a
star () in the parts list and in the schematic diagrams. To
ensure safe product operation, it is necessary to replace
those components with the exact same PARTS.
SERVICE ADJUSTMENTS
GENERAL
This set has an on-screen Service Menu system included in the CPU that allows remote operation for most of the service adjustments.
To enter the Service Menu, first disconnect the AC power cord. Then while pressing the MENU key on the front control panel, reconnect the AC power cord. The adjustments can now be made with the remote control or front control panel keys.
ON-SCREEN SERVICE MENU SYSTEM
TITLE
1. Enter the Service Menu:

While pressing the MENU key on the front control panel, reconnect the
AC power cord. The Service Menu Display will now appear. See Figure 1.
ITEM NO.
3C
15
SCO
00010101
2. Service Adjustments:
Press the or key to select the desired service menu item you
want to adjust. (See page 5 for On-screen Service Menu.)
HEX DATA
Use the + or key or number keys to adjust the data.

The + or keys will increase or decrease the data sequentially.
The number keys (0 ~ 7) toggle only their respective bits between
1 and 0 and are used to change the Sub-Address. For example to
change bit 5 press the number 5 key. See below.
BINARY DATA
(8 bit)
Figure 1. Service Menu Display
(b7) (b6) (b5) (b4) (b3) (b2) (b1) (b0)

BINARY DATA
(8 bit)
01010110
3. Exit from the Service Menu:
Press the MENU key to turn off the Service Menu display.
IC802 (EEPROM) REPLACEMENT

When IC802 (EEPROM) is replaced, IC801 (CPU) will automatically write the initial reference data into IC802 for basic TV operation.
However, the bus data should be checked and some bus data should be set up before attempting the service adjustments.
(See pages 5 7, Table 1, for detailed bus data information.)
INITIAL BUS DATA SETUP

Note: When IC802 (EEPROM) is replaced, change the following initial reference data for proper TV operation before
attempting service adjustments.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
Disconnect the AC power cord (AC 120V line).

While pressing the MENU key, reconnect the AC power cord. The Service Menu display will now appear.
Select NO. 3B SCN (Sub Contrast) with or key. Adjust the data with + or key for 10.
Select NO. 3C SCO (Sub Color) with or key. Adjust the data with + or key for 15.
Select NO. 3D STI (Sub Tint) with or key. Adjust the data with + or key for 05.
Select NO. 41 HP (H Phase) with or key. Adjust the data with + or key for 0F.
Select NO. 42 VS (V Size) with or key. Adjust the data with + or key for 5A.
Select NO. 43 VSP7VKI6VDC (V Sync Sep / V Kill / V DC) with or key. Adjust the data with number keys for 18.
Select NO. 44 HBL5VLN (H Blk L / V Lin ) with or key. Adjust the data with number keys for 35.
Select NO. 45 HBR5VST (H Blk R / V Lin Shift) with or key. Adjust the data with number keys for 43.
Select NO. 46 VSC (V S Correction) with or key. Adjust the data with + or key for 0E.
Select NO. 47 VTS6VC3CDM (V Test / V Comp / Count Dwn Mode) with or key. Adjust the data with number keys
for 28.
Select NO. 4F SBI (Sub Bias) with or key. Adjust the data with + or key for 30.
Select NO. 53 ABL5MSD4RTS3BAT (ABL Def / MID Stop / RGB Temp / ABL Thresh) with or key. Adjust the data
with number keys for 0C.
Select NO. 55 STR4FLS (S Trap Test / Filter System) with or key. Adjust the data with number keys for 21.
Select NO. 5B AF7CBP5 (Auto Flesh / C Band Pass) with or key. Adjust the data with number keys for A0.
Select NO. 5C CKO (Color Killer) with or key. Adjust the data with + or key for 03.
SERVICE ADJUSTMENTS (Cont.)

INITIAL BUS DATA SETUP (Cont.)
18. Select NO. 67 VMD6VMG3SSN (VM Delay / VM Gain / Sync Sep Sens) with or key. Adjust the data with number
keys for 22.
19. Select NO. 69 EWD (E/W DC) with or key. Adjust the data with + or key for 2A.
20. Select NO. 6A EWA (E/W Amp) with or key. Adjust the data with + or key for 16.
21. Select NO. 6B EWT (E/W Tilt) with or key. Adjust the data with + or key for 29.
22. Select NO. 6C ECB4ECT (E/W Corner Btm / E/W Corner Top) with or key. Adjust the data with number keys for 54.
23. Select NO. 83 OPT (Aspect Ratio / Surround) with or key. Adjust the data with + or key for A0.
24. Select NO. 84 OP2 (Component / V Guide) with or key. Adjust the data with + or key for 20.
25. Select NO. 86 CBR (RF C Bypass) with or key. Adjust the data with + or key for 00.
26. Select NO. 8C CBT (RF C BPF Test) with or key. Adjust the data with + or key for 08.
27. Select NO. 8D HR (H Display Position) with or key. Adjust the data with + or key for 24.
28. Select NO. 8E SBO (Sub Bright Offset) with or key. Adjust the data with + or key for 05.
29. Select NO. 98 DRY (YUV R-Y Difference) with or key. Adjust the data with + or key for 0B.
30. Select NO. 99 DBY (YUV B-Y Difference) with or key. Adjust the data with + or key for 10.
31. Select NO. A1 EEA (16:9 E/W Amp Difference) with or key. Adjust the data with + or key for F6.
32. Select NO. A7 EVB (16:9 V Blk Sw) with or key. Adjust the data with + or key for 60.
33. Press the MENU key to turn off the Service Menu display.
Table 1. ON-SCREEN SERVICE MENU

When IC802 (EEPROM) is replaced, check the bus data to confirm they are the same as below. The shaded menu should be
checked and be set up or readjusted according to the procedures described in the following pages. Initial Setup Data marked
with an * should be changed from Initial Reference Data. (See pages 3 and 4 for Initial Bus Data Setup.)
TITLE
INITIAL REFERENCE
DATA HEX
INITIAL SETUP
DATA HEX
INITIAL SETUP
DATA BINARY
3B
SCN
0F
10*
00010000
Sub Contrast (4~0)
3C
SCO
1F
15*
00010101
Sub Color (5~0)
3D
STI
07
05*
00000101
Sub Tint (4~0)
3E
SB
18
18
00011000
Sub Bright (5~0)
3F
SSH
00
00
00000000
Sub Sharpness (4~0)
40
AFC6HFR
90
90
10010000
AFC(6) Horizontal Frequency (5~0)
41
HP
12
0F*
00001111
Horizontal Phase (4~0)
42
VS
60
5A*
01011010
Vertical Size
43
VSP7VKI6VDC
07
18*
00011000
V Sync Sep (7) V Kill (6) V DC (5~0)
44
HBL5VLN
06
35*
00110101
H Blanking L (6~5) V. Linearity (4~0)
45
HBR5VST
20
43*
01000011
H Blanking R (6~5 V Shift (3~0)
46
VSC
0A
0E*
00001110
Vertical S Correction (4~0)
No.
FUNCTION
47
VTS6VC3CDM
38
28*
00101000
V Test (7~6) V Compression (5~3)Count Down Mode (0)
48
FBS4GRY2CRS
10
10
00010000
VNS (7) V Blk (6~5) FBP Blk (4) Gray Mode (2) CRS (1~0)
49
RB
00
00
00000000
Red Bias (7~0)
4A
GB
00
00
00000000
Green Bias (7~0)
4B
BB
00
00
00000000
Blue Bias (7~0)
4C
RD
40
40
01000000
Red Drive (6~0)
4D
GD
08
08
00001000
Green Drive (3~0)
4E
BD
40
40
01000000
Blue Drive (6~0)
4F
SBI
40
30*
00110000
Sub Bias (6~0)
50
51
52
OSD
03
03
00000011
On Screen Display Contrast (1~0)
53
ABL5MSD4RTS3BAT
04
0C*
00001100
ABL Defeat (5) MID Stop (4) RGB Temp (3) ABL Thresh (2~0)
54
CRG
12
12
00010010
Coring Gain (7~6)
55
STR4FLS
41
21*
00100001
S Trap Test (6~4) Y/C Filter Mode (2~0)
56
YAP6PRE4OVR2WP
00
00
00000000
Y APF (6) Pre Shoot (5~4) Over Shoot (3~2) White Peak (1~0)
57
YGM6DCR4BSS2BSG
04
04
00000100
Y Gam (7~6) DC Res (5~4) B Strk Start (3~2) B Strk Gain (1~0)
58
CBT3
60
60
01100000
Cb Trap (7~3)
59
Not Used
5A
Not Used
5B
AF7CBP5
20
A0*
10100000
Auto Flesh (7) C Bypass (5)
5C
CKO
07
03*
00000011
Color Killer (2~0)
5D
RYA
08
08
00001000
R-Y/B-Y Angle (3~0)
5E
CBO4CRO
98
98
10011000
Cb DC Offset (7~4) Cr DC Offset (3~0)
5F
GYA3
00
00
00000000
G-Y Angle (3)
60
61
FMM5
00
00
00000000
62
IAS7STS6RAD
60
60
01100000
IF AGC (7) S Trap SW (6) RF AGC (5~0)
63
VIF5VL
10
10
00010000
VIF System SW (5) Video Level (4~2)
64
VCO1
80
80
10000000
VCO Freq (7~1)
65
OMS6OML
20
20
00100000
Over Mod SW (6) Over Mod Level (5~2)
66
67
VMD6VMG3SSN
24
22*
00100010
Not Used
Not Used
Not Used
FM Mute (5)
Not Used
VM delay (7~6) VM Gain (5~3) Sync Sep Sens(2~0)
68
69
EWD
2E
2A*
00101010
6A
EWA
12
16*
00010110
E/W Amp (5~0)
6B
EWT
23
29*
00101001
E/W Tilt (5~0)
Not Used
E/W DC (5~0)
SERVICE ADJUSTMENTS (Cont.)

Table 1. ON-SCREEN SERVICE MENU (Continued)
No.
TITLE
INITIAL REFERENCE
DATA HEX
INITIAL SETUP
DATA HEX
INITIAL SETUP
DATA BINARY
FUNCTION
6C
ECB4ECT
33
54*
01010100
E/W Corner Bottom(7~4) E/W Corner Top (3~0)
6D
EWS7ETS3HSC
84
84
10000100
E/W Correction Sw(7) E/W Test (5~3) H Size Comp (2~0)
6E
Not Used
6F
80
ATT
07
07
00000111
Attenuation -MTS Input Level (3~0)
Not Used
81
WDB
20
20
00100000
Wide Band - Low Separation (5~0)
82
SPC
20
20
00100000
Spectral - High Separation (5~3)
83
OPT
80
A0*
10100000
Surround (7) Aspect Ratio (5)
84
OP2
00
20*
00100000
V Guide(7)
85
FLR
00
00
00000000
RF Filter System (2~0)
86
CBR
20
00*
00000000
RF C Bypass (5)
87
CDR
00
00
00000000
RF Count Down Mode (0)
88
CGR
40
40
01000000
RF Coring Gain (6)
89
AFR
00
00
00000000
RF AFC Gain & Gate (6)
8A
ROV
0C
0C
00001100
RF Over Shoot Adjust (3~2)
8B
RPR
00
00
00000000
RF Pre Shoot Adjust (5~4)
8C
CBT
00
08*
00001000
RF C BPF Test (4~3)
8D
HR
13
24*
00100100
OSD H Display Position (7~0)
8E
SBO
03
05*
00000101
Sub Bright Offset (5~0)
8F
DFL
02
02
00000010
YUV Filter System (2~0)
90
DCN
00
00
00000000
YUV Sub Contrast (6~0)
91
DBR
00
00
00000000
YUV Sub Bright (6~0)
92
DCL
00
00
00000000
YUV Sub Color (6~0)
93
DTN
00
00
00000000
YUV Sub Tint (6~0)
94
DSH
00
00
00000000
YUV Sub Sharpness (6~0)
95
DCG
00
00
00000000
YUV Sub Coring (6)
96
DVG
00
00
00000000
YUV Sub VM Gain (5~0)
97
DHS
00
00
00000000
YUV Sub E/W DC (5~0)
98
DRY
06
0B*
00001011
YUV R-Y Offset (3~0)
99
DBY
70
10*
00010000
YUV B-Y Offset (7~4)
9A
DYA
00
00
00000000
YUV APF (6)
9B
ECN
E0
E0
11100000
16:9 Sub Contrast (6~0)
9C
EBR
00
00
00000000
16:9 Sub Bright (6~0)
9D
ECL
00
00
00000000
16:9 Sub Color (6~0)
9E
ETN
00
00
00000000
16:9 Sub Tint (6~0)

16:9 Sub V Size (6~0)
9F
EVS
D4
D4
11010100
A0
EVP
00
00
00000000
16:9 Sub V Position (3~0)
A1
EEA
F8
F6*
11110110
16:9 Sub E/W Amp (5~0)
A2
EET
03
03
00000011
16:9 Sub E/W Tilt (5~0)
A3
EEP
FF
FF
11111111
16:9 Sub E/W Corner Top (3~0)
A4
EEB
00
00
00000000
16:9 Sub E/W Corner Bottom (7~4)
A5
EUV
00
00
00000000
16:9 Sub V Linearity (4~0)
A6
B16
00
00
00000000
16:9 ABL VTH Sw (5)
A7
EVB
A8
02
60*
01100000
16:9 V Blanking SW (6~5)
R40
R40
01000000
Red Drive Adjustment
(See Note 1.)
R40
R40
01000000
Blue Drive Adjustment
(See Note 1.)
Red Bias Adjustment
(See Note 2.)
Green Bias Adjustment
(See Note 2.)
Blue Bias Adjustment
(See Note 2.)
DRV
DRIVE AND BIAS ADJUSTMENTS
PROGRAM CODES
Note 1.
Red/Blue Drive Adjustments in Service Menu NO. A8 DRV:
Adjust Red and Blue Drive Levels alternately with 1, 3, 7,
and 9 keys on the remote control. See Figure 2. The Drive
Level adjustment data will be written in the Service Menu
No. 4C RD and 4E BD automatically.
The microprossesor used in this model is a multi-purpose

type and is used in several different models. To ensure
proper operation and the correct features for your particular model, the program codes must be correct.
RD()
(N/A)
RD(+)
(N/A)
(N/A)
(N/A)
BD()
(N/A)
BD(+)
Note 1. Option Data 1 (NO. 83 OPT) should be hexadecimal

A0 (10100000 binary). See page 4 INITIAL DATA SETUP,
step 23, for set up procedure. If this program code is wrong
the TV will not operate properly.
FOR RED DRIVE ADJUSTMENT

BIT
FOR BLUE DRIVE ADJUSTMENT
Figure 2.
Note 2.
Red/Green/Blue Bias Adjustments in Service Menu
A9 (No Vertical Sweep):
Adjust each Bias Level with 1, 3, 4, 6, 7, or 9 key on the
remote control. See Figure 3. The Bias Level adjustment
data will be written in the Service Menu No. 49 RB,
No. 4A GB, and No. 4B BB automatically.
1
RB()
(N/A)
RB(+)
GB()
(N/A)
GB(+)
BB()
(N/A)
BB(+)
FOR RED BIAS ADJUSTMENT
FUNCTION
DATA
0
0~1
TV / HOTEL / MON
N/A
N/A
VIDEO MODE
NONE
YES
3~4
CLOCK
N/A
N/A
ASPECT RATIO
NONE
YES
NOT USED
SURROUND
NONE
YES
Note 2. Option Data 2 (NO. 84 OP2) should be hexadecimal

20 (00100000 binary). See page 4 INITIAL DATA SETUP,
step 24, for set up procedure. If this program code is wrong
the TV will not operate properly.
FOR GREEN BIAS ADJUSTMENT
BIT
0
FOR BLUE BIAS ADJUSTMENT
Figure 3.
FUNCTION
V-GUIDE
DATA
0
NONE
YES
N/A
N/A
N/A
COLOR ENHANCER
INITIAL CH & XDS
N/A
NOT USED
PIP
N/A
N/A
COMPONENT
NONE
YES
BASS & TREBLE / TONE
N/A
N/A
GAME
N/A
N/A
SERVICE ADJUSTMENTS (Continued)

ANTENNA CONNECTIONS
VERTICAL CENTERING ADJUSTMENT
This receiver is designed for UHF/VHF reception. A 75 ohm

terminal is provided for UHF and VHF receptions. When
connecting a CATV antenna system, connect the 75 ohm
coaxial cable directly to the 75 ohm terminal. For 300 ohm
VHF antenna, use an adapter (not included with the TV set).
1. Tune receiver to an active channel.

2. Check that picture is in the center of TV screen. If picture
center is too low, change resistor R513 from 1K ohm 1W to
470 ohm 1W. If picture center is too high, add resistor R512
(1K ohm, 1/2W).
CIRCUIT PROTECTION
RF AGC ADJUSTMENT
Fuse F601 (4A) is included in the AC line. This fuse must be

replaced with the proper fuse (see Parts List).
1. Tune receiver to strongest VHF station in your area.

2. Set contrast and brightness controls for maximum.
3. Turn off the receiver and disconnect the AC power cord
(120V AC line).
4. While pressing the MENU key, reconnect the AC power
cord. The Service Menu display will now appear.
5. Select NO. 62 RAD (RF AGC Delay) with or key.
6. Adjust the data with + or key in the direction which
causes snow to appear; then in the opposite direction
until the snow just disappears.
7 . To turn off the Service Menu display, press the MENU key.
CAUTION
4A 125V
FOR CONTINUED PROTECTION AGAINST

A RISK OF FIRE, REPLACE ONLY WITH
THE SAME TYPE 4A, 125V FUSE.
ATTENTION : POUR MAINTENIR LA PROTECTION CONTRE LES RISQUES
D INCENDIE UTILISER UN FUSIBLE DE
RECHANGE DE MEME TYPE 4A, 125V.
+B VOLTAGE CHECK
Connect Voltmeter + lead to TJ1 130V and lead to ground
(TE7). Connect receiver to AC 120V line. Tune receiver to an
active channel. Reset the picture controls to the FACTORY
PRESET levels (press remote control RESET key twice).
Voltage must measure between +128.0V and +132.0V. If the
voltage is out of this range, the power circuit must be
checked. No +B adjustment is provided on this chassis.
HORIZONTAL CENTERING ADJUSTMENT

2. Check that picture is in the horizontal center of TV screen.
If picture is not centered horizontally, perform steps 3 ~ 6.
3. Turn off the receiver and disconnect the AC power cord.
5. Select NO. 41 HP (Horizontal Phase) with or key.
6. Adjust the data with + or key for horizontal center. To
turn off the Service Menu display, press the MENU key.
VIDEO LEVEL
1. Connect color-bar generator to antenna terminals.
(AC 120V line).
3. Connect oscilloscope to TP16 (Q132 emitter) and ground.
4. While pressing the Menu key, reconnect the AC power
cord. The Service Menu will now appear.
5. Select NO. 63 VL (Video Level) with the or key.
6. Adjust with the number keys (4~2) for an oscilloscope
reading of 1.0 0.1 VP-P at TP16. Press the MENU key to
turn off the Service Menu display.
1.0 0.1 VP-P
VERTICAL SIZE ADJUSTMENT

2. Check the vertical size of the picture. If the vertical size is
too large or small, perform steps 3 ~ 6.
5. Select NO. 42 VS (Vertical Size) with or key.
6. Adjust the data with + or key for full scan. To turn off
the Service Menu display, press the MENU key.
Figure 4.
GRAYSCALE ADJUSTMENT
FOCUS ADJUSTMENT
1. Set the picture controls to the Auto levels or Reset (use

MENU key and or key or RESET key).
(120V AC line).
4. Select NO. 49 RB (Red Bias), NO. 4A GB (Green Bias),
and NO. 4B BB (Blue Bias) with or key and set each
data to 0 with + or key.
5. Select NO. 4C RD (Red Drive) and NO. 4E BD (Blue Drive)
with or key and set each data to 40 with + or key.
6. Set NO. 4D GD (Green Drive Reduction) data to 08, NO. 3E
SB (Sub-Brightness) data to 18, NO. 3C SCO (Sub Color)
data to 15, NO. 3D STI (Sub Tint) to 05, and NO. 3F SSH
(Sub Sharpness) data to 00 with or , and + or keys.
7. Turn Screen Control (T402) to minimum (fully counterclockwise).
8. Select the Service Menu NO. A9 (No Vertical Sweep)
with or key.
9. Advance Screen Control (T402) clockwise to obtain just
visible one color line. If line does not appear, place this
control to maximum (fully clockwise).
10. Raise each Bias Level with 3, 6, and 9 keys to obtain just
visible white line. See Figure 5.
Adjust focus control (T402) for well defined scanning lines.
1
RB()
(N/A)
RB(+)
GB()
(N/A)
GB(+)
BB()
(N/A)
BB(+)

11. Select the Service Menu NO. A8 DRV (Drive Adjustments)

with or key.
12. Adjust Red and Blue Drive Levels alternately with 1, 3,
7, or 9 key to produce normal black and white picture in
highlight areas. See Figure 6.
1
(N/A)
RD(+)
(N/A)
(N/A)
(N/A)
BD()
(N/A)
BD(+)
Note: +B (+130V) Voltage Check and Grayscale Adjustment

must be completed before attempting high voltage
Check.
1. Connect high voltage voltmeter lead to ground, and
connect + lead to anode of picture tube.
2. Tune receiver to an active channel and confirm TV is
operating properly.
3. Eliminate the beam current by adjusting the contrast
and brightness controls to minimum.
4. Confirm high voltage is within 28.0 KV and 31.1 KV. If
reading is not within range, check horizontal circuit.
No high voltage adjustment is provided on this chassis.
BRIGHTNESS LEVEL ADJUSTMENT

Note: Grayscale, RF AGC, Video Level, and High Voltage Check
must be adjusted before attempting Brightness Level
Adjustment.
1.
2.
3.
4.
Figure 5. Remote Control Number keys functions in

Service Menu NO. A9 (No Vertical Sweep)
RD()
HIGH VOLTAGE CHECK
5.
6.
7.
8.
9.
10.
Connect a color-bar generator to the antenna terminals.

Switch the generator to the crosshatch pattern.
Reset the picture controls to the Auto levels.
Connect voltmeter (high impedance) + lead to terminal
TP51 and lead to terminal TP50 on main board. Set
voltmeter for 1.5V ~ 3V range.
Turn off the receiver and disconnect the AC power cord.
While pressing the MENU key, reconnect the AC power
Select NO. 3E SB (Sub Brightness) with or key.
Adjust the data with + or key for 680mVDC.
Check brightness level on every active channel, readjust
(repeat steps 5 ~ 9), if necessary.
Note: Do not set to excessive brightness level, otherwise

the contrast level will be suppressed.

Service Menu NO. A8 DRV
13. Check for proper grayscale at all brightness levels.
To turn off the Service Menu display, press the MENU key.
Note: If Grayscale Adjustment is made after picture tube
replacement, check Brightness Level Adjustment.

SEPARATION ADJUSTMENT
Every time the receiver is serviced, the HIGH VOLTAGE

HOLD-DOWN circuit must be tested for proper operation by
following these steps:

(AC 120V line).
8. Connect oscilloscope CH1 to TP317 and CH2 to TP318
and ground.
9. Connect an MTS TV/Stereo generator to antenna terminal.
11. Select pilot, 300Hz audio frequency and Left modulating
signal.
12. Select NO. 81 WDB (Wide Band) with the or key.
13. Adjust the + or key for minimum low frequencies at
TP317. See Figure 7.
14. Select 4 KHz audio frequency and Right modulating signal.
15. Select NO. 82 SPC (Spectral) with the or key.
16. Adjust the + or key for minimum high frequencies at
1. Connect receiver to 120V AC line. Tune receiver to

active channel. Reset the picture controls to the Auto
levels.
2. Check that the voltage measured between TP7 and TE7
(ground side) is within 16.5 VDC to 21 VDC. If the voltage is out of this range, the Hold-Down Circuit must be
checked.
3. Connect a DC Voltage supply to TP7 and TE7 through a
100 ohm 1/4W resistor. Adjust the DC voltage to 23 VDC.
The receiver should shutdown, losing raster and sound.
Then the receiver should turn off automatically. This
reaction indicates that the Hold-Down circuit is functioning properly. If the receiver does not shutdown, a
malfunction is indicated and its cause must be found
and corrected.
4. To obtain picture again, remove the DC Supply and wait
a few minutes. Now turn on the receiver.
Repeat adjustments (steps 1116) until no further decreases

in amplitude can be obtained. Press the MENU key to turn
off the Service Menu display.
MULTI-SOUND SECTION ADJUSTMENTS
Minimize L leakage
Note: Multi-Sound Section must be adjusted after

IC801 (CPU / Signal Processor), IC3401 (MTS
Decoder), or IC802 (EEPROM) is replaced.
TP317 (R)
300Hz
Minimize R leakage
INPUT LEVEL ADJUSTMENT

1. Connect a signal to the antenna terminals with audio of
1 KHZ 100% modulation.
(AC 120V line).
3. Connect voltmeter (RMS) to TP317 and ground.
5. Select NO. 80 ATT (Attenuation) with the or key.
6. Adjust the + or key for a voltmeter reading of 400 20
mVrms at TP317.
10
TP318 (L)
4KHz
Figure 7. Separation Adjustments
SERVICE HINTS
POWER FAILURE DETECTOR
This unit is equipped with a Power Failure Detector function included in the CPU which checks for an abnormal condition in
the chassis power supplies, including the power supply derived from the Horizontal Output Transformer.
If, while the power is on, a failure is caused by any of the following that results in a low voltage supply, the CPU will turn the
unit off in 1.5 seconds to prevent further damage:
Failure within the power supply circuits.

A short circuit in the load side from the supply.
Stoppage of the Horizontal Output Oscillator caused by the X Radiation protection Hold-Down Circuit.
If, while the power is off, the power is switched on and any of these failures remains uncorrected, the CPU will shut off the
power within three seconds.
Check the following if the unit is turned off by the power failure detector.
1. Disconnect the AC power cord (120V AC line) for at least 10 seconds.
2. Connect a DC Voltmeter to the following TEST POINTS.
TJ6
D002 Cathode
D429 Cathode
D806 Cathode
5V
15V
5V
30V
3. Press the Power key and check for the proper voltage supplies.
4. If any of these voltages is low, the power failure detector should turn the unit off within three seconds.
5. Check all circuits listed above.
Note: This unit is equipped with a Power Surge Protection feature included in the CPU. If power failure occurs three times
within 15 minutes, the CPU will automatically stop functioning to help prevent secondary damage. (TV will not turn on
by pressing the power key.) To reset the operating programs within the CPU, disconnect the AC power cord for at least
10 seconds.
11
MECHANICAL DISASSEMBLIES
CABINET BACK REMOVAL
CHASSIS REMOVAL
1. Refer to Figure 1, remove 8 screws.

2. Pull off cabinet back and remove.
1. Remove cabinet back.

2. Discharge the picture tube anode (2nd anode lead) to the
dag coating (picture tube grounding lead).
3. Disconnect degaussing coil socket (KD), picture tube
socket, deflection yoke connector (KX), speaker
connector (KSP), picture tube ground leads, and 2nd
anode lead.
4. Remove chassis completely by sliding it straight back.
PICTURE TUBE REMOVAL

CAUTION: Do not disturb the deflection yoke or magnet
assembly on the picture tube neck. Care must be taken to
keep these assemblies intact, unless picture tube is being
replaced. Discharge the picture tube to the coating before
handling the tube.
AV2 INPUT
R
AUDIO
L
S-VIDEO
(MONO)
1. Remove chassis, see Chassis Removal instructions.

2. Place cabinets front face down on a soft surface.
3. Remove the screw on each corner of the picture tube and
GENTLY lift the picture tube out of the cabinet.
4. Install a replacement picture tube in reverse order.
Properly install the degaussing coil and picture tube
grounding lead on the picture tube. See Figure 2.
UHF / VHF / CATV

75
VIDEO
Figure 1. Cabinet Back Removal
Note: If Picture Tube is being replaced, mount the Degaussing

Coil properly on the tube. See Figure 2.
DEGAUSSING
COIL
DEGAUSSING
COIL HOLDER
DEGAUSSING
COIL HOLDER
TO PICTURE TUBE
SOCKET BOARD
GROUND
DEGAUSSING
COIL SOCKET
PICTURE-TUBE
GROUNDING LEAD
Figure 2. Picture Tube Removal
12
CHASSIS ELECTRICAL PARTS LIST

CAUTION: To Protect against electrical shock and for continued product safety, refer to SAFETY PRECAUTIONS,
X-RADIATION PRECAUTIONS, HIGH VOLTAGE HOLD-DOWN TEST, and PRODUCT SAFETY NOTICE on Page 2.

PRODUCT SAFETY SHOULD BE CONSIDERED WHEN A REPLACEMENT IS MADE IN ANY AREA OF A RECEIVER.
COMPONENTS INDICATED BY A STAR () IN THIS PARTS LIST AND THE SCHEMATIC DIAGRAM DESIGNATE
COMPONENTS IN WHICH SAFETY CAN BE OF SPECIAL SIGNIFICANCE. IT IS PARTICULARLY RECOMMENDED
THAT ONLY PARTS DESIGNATED ON THE FOLLOWING PARTS LIST BE USED FOR COMPONENT REPLACEMENT
DESIGNATED BY A STAR. NO DEVIATIONS FROM RESISTANCE, WATTAGE, AND VOLTAGE RATINGS MAY BE MADE
FOR REPLACEMENT ITEMS DESIGNATED BY A STAR.
Notes: Parts having Location Number are located on the following boards.
Numbers under 700 Series . . . . . . . . . . . . . . . . . . . . .On the Main Board.
Numbers 700 Series . . . . . . . . . . . . . . . . . . . . . . . . . . .On the Picture Tube Socket Board.
Numbers 900 Series . . . . . . . . . . . . . . . . . . . . . . . . . . .Out of Board.
All Other Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . .On the Main Board
Note: Schematic part location numbers may not always match with the part descriptions.
The part descriptions are correct and should be used.
Schematic
Location
Part No.
Schematic
Location
Description
CAPACITORS
NOTES:
Read description of the Capacitor as follows:
(Example)
CERAMIC
100P
50V
Rated Voltage
Tolerance Symbols:
less than 10PF
A . .Not specified
B . .0.1PF
C . .0.25PF
D . .0.5PF
F . .1PF
G . .2PF
R . .+0.25 - 0PF
S . .+0 - 0.25PF E . .+0 - 1PF
more than 10PF
A . .Not specified
B . .0.1%
C . .0.25%
D . .0.5%
F . .1%
G . .2%
H . .3%
J . .5%
K . .10%
L . .15%
M . .20%
N . .30%
P . .+100 - 0%
Q . .+30 - 10% T . .+50 - 10%
U . .+75 - 10% V . .+20 - 10%
W .+100 - 10% X . .+40 - 20%
Y . .+150 - 10% Z . .+80 - 20%
Rated Value: P...Pico Farad U...Micro Farad
Material:
CERAMIC . . . . . .Ceramic
MT-PAPER . . . . .Metalized Paper
POLYESTER . . .Polyester
MT-POLYEST . .Metalized Polyester
POLYPRO . . . . .Polypropylene
MT-POLYPRO . .Metalized Polypropylene
COMPO-FILM . .Composite Film
MT-COMPO . . . .Metalized Composite
STYRENE . . . . . .Styrene
TA-SOLID . . . . .Tantalum Solid
AL-SOLID . . . . . .Aluminum Solid
ELECT . . . . . . . .Electrolytic
NP-ELECT . . . . .Non-Polarized Electrolytic
OS-SOLID . . . . .Aluminum Solid with Organic
Semiconductive Electrolytic
13
C001
C002
C003
C004
C006
C010
C011
C012
C015
C101
C103
C106
C131
C132
C133
C134
C137
C138
C140
C141
C142
C143
C144
C147
C148
C201
C202
C203
C204
C206
C207
C208
C209
C211
C212
C213
C214
Part No.
404 084 3801

404 084 3801
403 235 5701
403 235 5701
403 224 6108
404 084 3009
404 084 3009
404 088 5702
404 084 3108
404 091 6406
403 224 6108
404 084 4105
403 364 7508
403 343 4603
401 150 6001
404 084 3801
403 224 5705
403 224 6108
403 235 1208
404 086 6503
403 296 0004
404 084 3207
403 224 6108
403 224 6108
404 084 2200
404 084 2804
403 224 6108
404 084 2705
404 084 4105
404 084 2705
403 224 6108
401 150 6001
403 323 3602
404 084 3702
404 091 6604
404 091 6604
404 084 4006
Description
ELECT
ELECT
CERAMIC
CERAMIC
CERAMIC
ELECT
ELECT
ELECT
ELECT
ELECT
CERAMIC
ELECT
CERAMIC
CERAMIC
MT-GLAZE
ELECT
CERAMIC
CERAMIC
CERAMIC
POLYESTER
CERAMIC
ELECT
CERAMIC
CERAMIC
ELECT
ELECT
CERAMIC
ELECT
ELECT
ELECT
CERAMIC
MT-GLAZE
CERAMIC
ELECT
ELECT
ELECT
ELECT
1U M 50V
1U M 50V
5600P K 50V
5600P K 50V
0.01U K 50V
220U M 16V
220U M 16V
22U M 16V
330U M 16V
220U M 6.3V
0.01U K 50V
3.3U M 50V
10P J 50V
0.022U K 50V
0.000 ZA 1/10W
1U M 50V
1000P K 50V
0.01U K 50V
330P J 50V
0.047U J 63V
0.1U K 25V
47U M 16V
0.01U K 50V
0.01U K 50V
100U M 6.3V
100U M 16V
0.01U K 50V
10U M 16V
3.3U M 50V
10U M 16V
0.01U K 50V
0.000 ZA 1/10W
0.047U K 50V
0.47U M 50V
4.7U M 25V
4.7U M 25V
2.2U M 50V
Schematic
Location
C216
C401
C402
C403
C404
C406
C407
C408
C411
C416
C421
C427
C471
C473
C482
C484
C489
C493
C497
C501
C502
C503
C504
C506
C508
C511
C516
C518
C601
C606
C608
C609
C612
C613
C614
C622
C625
C626
C628
C629
C630
C631
C632
C683
C693
C701
C702
Part No.
403 224 6108

404 087 1903
403 224 6108
404 084 6901
403 235 5800
403 075 7101
403 076 3102
404 085 4609
403 343 7901
404 077 4402
403 346 7126
403 372 6807
403 392 8508
404 091 6406
403 224 6108
404 084 3306
403 256 0808
404 084 5706
404 087 4102
404 084 4204
404 084 3009
404 056 5307
404 084 3207
404 084 4501
404 084 4402
403 276 0208
404 085 4500
404 089 5909
403 028 1705
403 237 7901
403 394 8407
404 084 3900
404 084 5706
404 096 0706
404 088 2909
404 088 7102
403 222 1303
403 262 1806
403 271 9602
404 049 4706
404 085 9000
404 090 9002
404 086 6800
404 084 5003
404 087 3402
403 262 2308
403 266 4902
404 084 2903
404 073 9005
404 091 9704
404 084 3009
404 084 3801
404 088 2909
404 088 7102
404 088 2909
404 088 7102
404 088 5702
404 086 5100
403 235 1109
403 069 8305
Schematic
Location
Description
CERAMIC
ELECT
CERAMIC
NP-ELECT
CERAMIC
CERAMIC
CERAMIC
ELECT
MT-POLYPRO
MT-POLYPRO
MT-POLYPRO
MT-POLYPRO
MT-POLYPRO
ELECT
CERAMIC
ELECT
MT-COMPO
MT-POLYEST
ELECT
ELECT
ELECT
NP-ELECT
ELECT
ELECT
ELECT
ELECT
ELECT
POLYESTER
CERAMIC
MT-COMPO
POLYESTER
ELECT
MT-POLYEST
MT-POLYEST
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
ELECT
ELECT
POLYESTER
POLYESTER
POLYESTER
ELECT
CERAMIC
CERAMIC
ELECT
ELECT
ELECT
ELECT
ELECT
CERAMIC
CERAMIC
CERAMIC
CERAMIC
ELECT
POLYESTER
CERAMIC
CERAMIC
0.01U K
330U M
0.01U K
1U M
6800P K
1000P K
3900P K
47U M
7200P H
7200P H
0.27U J
0.27U J
0.27U J
220U M
0.01U K
470U M
0.47U J
0.47U J
22U M
4.7U M
220U M
2.2U M
47U M
470U M
220U M
2.2U K
2200U M
5600P K
56P J
0.22U J
0.22U K
10U M
0.47U J
0.22U M
1000P M
1000P M
1000P K
1000P K
1000P K
330U M
330U M
3300P J
6800P J
0.01U J
1000U M
1200P K
1200P K
1000U M
220U M
220U M
220U M
1U M
1000P M
1000P M
1000P M
1000P M
22U M
0.1U J
270P J
0.01U Z
50V
10V
50V
50V
50V
500V
500V
35V
1.5KV
1.5K
250V
250V
250V
6.3V
50V
16V
50V
63V
100V
50V
16V
100V
16V
35V
35V
50V
25V
63V
50V
50V
50V
50V
63V
275V
250V
250V
1K
1K
1K
200V
200V
63V
63V
63V
35V
1K
1K
16V
160V
160V
16V
50V
250V
250V
250V
250V
16V
63V
50V
50V
C711
C721
C742
C801
C802
C806
C811
C829
C862
C863
C864
C866
C868
C869
C1004
C1006
C1007
C1051
C1052
C1059
C1101
C1102
C1103
C1902
C3401
C3404
C3406
C3407
C3408
C3411
C3412
C3413
C3414
C3416
C3417
C3418
C3421
C3422
C3423
C3424
C3426
C3427
C3431
C3432
C3433
C3434
C3436
C3439
Part No.
403 235 1109

403 235 1109
403 077 2807
403 224 6108
404 084 3207
404 091 6406
404 084 3801
404 084 3801
403 234 9809
403 234 9809
403 224 6108
404 084 3207
403 358 0102
404 084 4006
404 084 4006
404 091 6604
404 091 6604
404 088 5702
403 296 0004
404 084 2705
404 084 4006
404 091 6604
404 091 6604
404 084 2705
404 087 1200
404 089 6500
403 325 2504
403 235 5701
404 084 3702
404 084 3702
404 084 3207
404 091 6604
404 084 2804
404 089 6500
404 091 6604
404 089 6500
403 224 5606
403 323 3602
403 342 9203
404 089 6500
403 299 1820
404 084 3801
403 224 6009
404 087 1200
403 224 6009
403 343 4603
404 089 6500
404 089 6500
Description
CERAMIC
CERAMIC
CERAMIC
CERAMIC
ELECT
ELECT
ELECT
ELECT
CERAMIC
CERAMIC
CERAMIC
ELECT
CERAMIC
ELECT
ELECT
ELECT
ELECT
ELECT
CERAMIC
ELECT
ELECT
ELECT
ELECT
ELECT
ELECT
NP-ELECT
CERAMIC
CERAMIC
ELECT
ELECT
ELECT
ELECT
ELECT
NP-ELECT
ELECT
NP-ELECT
CERAMIC
CERAMIC
TA-SOLID
NP-ELECT
TA-SOLID
ELECT
CERAMIC
ELECT
CERAMIC
CERAMIC
NP-ELECT
NP-ELECT
270P J
270P J
1000P Z
0.01U K
47U M
220U M
1U M
1U M
18P J
18P J
0.01U K
47U M
0.033U K
2.2U M
2.2U M
4.7U M
4.7U M
22U M
0.1U K
10U M
2.2U M
4.7U M
4.7U M
10U M
0.1U M
4.7U M
0.012U K
5600P K
0.47U M
0.47U M
47U M
4.7U M
100U M
4.7U M
4.7U M
4.7U M
2700P K
0.047U K
3.3U K
4.7U M
10U K
1U M
4700P K
0.1U M
4700P K
0.022U K
4.7U M
4.7U M
50V
50V
2K
50V
16V
6.3V
50V
50V
50V
50V
50V
16V
50V
50V
50V
25V
25V
16V
25V
16V
50V
25V
25V
16V
50V
50V
50V
50V
50V
50V
16V
25V
16V
50V
25V
50V
50V
50V
10V
50V
10V
50V
50V
50V
50V
50V
50V
50V
DIODES
D002
D101
D351
D408
D421
D422
14
407 013 4306

407 013 7109
408 008 2406
408 047 6205
408 047 6502
407 222 4401
407 158 1307
407 158 1307
DIODE 1S2076A
DIODE 1S2473
DIODE 1N4148
ZENER DIODE MTZJ36A (36V)
ZENER DIODE MTZJ5.1A (5.1V)
ZENER DIODE 1Z150 (150V)
ZENER DIODE HZ11B2L (11V)
Schematic
Location
D428
D429
D471
D472
D481
D482
D486
D487
D490
D501
D502
D601
D602
D603
D604
D612
D613
D614
D623
D624
D625
D680
D683
D693
D699
D801
Part No.
407 054 5904

407 099 7109
407 013 4306
407 013 7109
408 008 2406
407 006 4108
407 007 7603
407 005 7308
407 005 8602
407 088 6502
407 007 6606
407 124 5506
407 124 6404
407 011 4407
407 054 0008
407 099 6102
407 005 8602
407 011 3004
407 088 6502
408 009 9404
408 047 7707
407 005 7308
407 005 8602
407 088 6502
407 118 2207
407 005 7605
407 013 3200
408 008 8606
407 005 7605
407 013 3200
408 008 8606
407 005 7605
407 013 3200
408 008 8606
407 005 7605
407 013 3200
408 008 8606
407 218 0707
407 231 2801
407 057 9800
407 063 9702
407 006 0100
407 007 6606
407 124 5506
407 124 6404
407 106 2806
407 129 7000
407 211 5808
407 013 4306
407 013 7109
408 008 2406
407 013 4306
407 013 7109
408 008 2406
407 099 5600
407 006 0100
407 013 4306
407 013 7109
408 008 2406
Description
ZENER DIODE RD15EB3 (15V)

ZENER DIODE MTZJ15C (15V)
DIODE 1S2076A
DIODE 1S2473
DIODE 1N4148
DIODE ERB44-04
DIODE EU2
DIODE EM01Z
DIODE ERA15-02
DIODE MPG06D
DIODE ES1
DIODE RMPG06G
DIODE ERA18-04
DIODE TVR1G
ZENER DIODE MTZJ10B (10V)
DIODE ERA15-02
DIODE S5277B
DIODE MPG06D
DIODE 1N4002ID
ZENER DIODE MTZJ5.6C (5.6V)
DIODE EM01Z
DIODE ERA15-02
DIODE MPG06D
DIODE EM2B
DIODE 1S1887A
DIODE GP15G
DIODE EM2B
DIODE 1S1887A
DIODE GP15G
DIODE EM2B
DIODE 1S1887A
DIODE GP15G
DIODE EM2B
DIODE 1S1887A
DIODE GP15G
PC TLP421(BL)
PHOTO COUPLE PC123YC2
ZENER DIODE RD9.1EB3 (9.1V)
DIODE ERA91-02
DIODE ES1
DIODE RMPG06G
DIODE ERA18-04
DIODE RU3YX
DIODE RU4AM LF-L1
DIODE FE201-6L43
DIODE 1S2076A
DIODE 1S2473
DIODE 1N4148
DIODE 1S2076A
DIODE 1S2473
DIODE 1N4148
DIODE ERA91-02
DIODE 1S2076A
DIODE 1S2473
DIODE 1N4148
Schematic
Location
D806
D831
D834
D836
D843
D1051
D1052
D1059
D1901
Part No.
407 013 4306

407 013 7109
408 008 2406
407 222 5903
408 047 4706
407 013 4306
407 013 7109
408 008 2406
407 013 4306
407 013 7109
408 008 2406
408 047 2306
408 047 2306
407 206 5608
408 047 9206
Description
DIODE 1S2076A
DIODE 1S2473
DIODE 1N4148
ZD UDZS-TE-173.6B (3.6V)
DIODE 1S2076A
DIODE 1S2473
DIODE 1N4148
DIODE 1S2076A
DIODE 1S2473
DIODE 1N4148
ZENER DIODE UDZS10B (10V)
INTEGRATED CIRCUITS
IC001
IC501
IC601
IC681
IC801
IC802
IC1001
IC3401
409 275 7903

409 340 1904
409 172 8102
409 528 6202
410 497 4106
409 333 3700
409 376 1503
409 440 8902
409 495 6908
409 528 8404
409 424 4906
409 467 1108
IC LA4525
IC LA7841
IC SE130NH
IC PQ050ES1MXP
IC LA76950
IC 24LC02B/P
IC ST24C02B6
IC M24C02-BN6
IC CAT24WC02P
IC S524A40X21-DCB0
IC NJM2533M
IC CXA2134Q-T6
COILS
LF601
L143
L602
L623
L625
L627
L701
L801
L811
L812
L901
L1901
15
645 012 0589

645 052 6862
610 031 3873
645 016 2534
645 005 0763
610 078 5946
652 000 1725
610 078 5946
652 000 1725
645 005 0763
610 029 8484
645 008 0012
645 008 2894
645 016 3104
645 006 2490
645 016 2411
645 006 2490
645 016 2411
645 060 9596
645 008 2894
645 016 3104
LINE FILTER
LINE FILTER
INDUCTOR, 10U K
INDUCTOR, 10U K
CORE, PIPE
PIPE CORE
CORE, PIPE
PIPE CORE
CORE, PIPE
CORE, PIPE
PEAKING COIL 330UH K
INDUCTOR, 330U K
INDUCTOR, 5.6U K
INDUCTOR, 5.6U K
INDUCTOR, 1U K
INDUCTOR, 1U K
INDUCTOR, 1U K
INDUCTOR, 1U K
DEGAUSSING COIL
INDUCTOR, 5.6U K
INDUCTOR, 5.6U K
Schematic
Location
Part No.
Schematic
Location
Description
TRANSISTORS
Q001
Q005
Q131
Q132
Q401
Q402
Q486
Q490
Q601
Q613
Q627
Q681
405 011 8401

405 011 8500
405 011 8609
405 012 2002
405 012 2101
405 012 2309
405 020 7501
405 020 7709
405 020 7907
405 151 8705
405 157 0505
405 008 4805
405 008 4904
405 011 8401
405 011 8500
405 011 8609
405 012 2002
405 012 2101
405 012 2309
405 020 7501
405 020 7709
405 020 7907
405 151 8705
405 157 0505
405 001 7407
405 001 7605
405 004 3109
405 004 3208
405 006 1707
405 006 1806
405 151 3304
406 000 6804
405 018 0507
405 018 0606
406 017 4602
405 023 5009
405 023 5306
405 023 5009
405 023 5306
405 148 1801
405 016 9502
405 009 6907
405 009 7003
405 089 0000
405 089 0109
405 011 8401
405 011 8500
405 011 8609
405 012 2002
405 012 2101
405 012 2309
405 020 7501
405 020 7709
405 020 7907
405 151 8705
405 157 0505
Q693
TR 2SC1740S-Q
TR 2SC1740S-R
TR 2SC1740S-S
TR 2SC1815-GR
TR 2SC1815-O
TR 2SC1815-Y
TR 2SC945A-PA
TR 2SC945A-QA
TR 2SC945A-RA
TR 2SC536NG-NPA
TR 2SC536NF-NPA
TR 2SB764-E
TR 2SB764-F
TR 2SC1740S-Q
TR 2SC1740S-R
TR 2SC1740S-S
TR 2SC1815-GR
TR 2SC1815-O
TR 2SC1815-Y
TR 2SC945A-PA
TR 2SC945A-QA
TR 2SC945A-RA
TR 2SC536NG-NPA
TR 2SC536NF-NPA
TR 2SA1015-O(SAN)
TR 2SA1015-Y(SAN)
TR 2SA564A-Q(CU)
TR 2SA564A-R(CU)
TR 2SA933S-Q
TR 2SA933S-R
TR 2SA608NF-NPA
TR 2SA1015-GR(SAN)
TR 2SC3332-R
TR 2SC3332-S
TR TT2168LS-YB11
TR 2SD400-E-MP
TR 2SD400-F-MP
TR 2SD400-E-MP
TR 2SD400-F-MP
TR 2SK2638
TR 2SC3069
TR 2SB985-S
TR 2SB985-T
TR 2SA1707-S
TR 2SA1707-T
TR 2SC1740S-Q
TR 2SC1740S-R
TR 2SC1740S-S
TR 2SC1815-GR
TR 2SC1815-O
TR 2SC1815-Y
TR 2SC945A-PA
TR 2SC945A-QA
TR 2SC945A-RA
TR 2SC536NG-NPA
TR 2SC536NF-NPA
Q695
Q701
Q711
Q721
Q831
16
Part No.
405 011 8401

405 011 8500
405 011 8609
405 012 2002
405 012 2101
405 012 2309
405 020 7501
405 020 7709
405 020 7907
405 151 8705
405 157 0505
405 001 7605
405 004 3208
405 004 4809
405 041 6507
405 041 6705
405 066 4304
405 066 9903
405 067 0008
405 067 0107
406 000 3605
405 041 6507
405 041 6705
405 066 4304
405 066 9903
405 067 0008
405 067 0107
406 000 3605
405 041 6507
405 041 6705
405 066 4304
405 066 9903
405 067 0008
405 067 0107
406 000 3605
405 002 0308
405 002 0407
405 002 6726
405 002 6924
405 134 5925
405 147 2205
405 163 1503
405 163 2708
405 173 9605
405 173 9704
Description
TR 2SC1740S-Q
TR 2SC1740S-R
TR 2SC1740S-S
TR 2SC1815-GR
TR 2SC1815-O
TR 2SC1815-Y
TR 2SC945A-PA
TR 2SC945A-QA
TR 2SC945A-RA
TR 2SC536NG-NPA
TR 2SC536NF-NPA
TR 2SA1015-Y(SAN)
TR 2SA564A-R(CU)
TR 2SA608-F-CTV-NP
TR 2SC2621-D-RA
TR 2SC2621-E-RA
TR 2SC2621-C-RA
TR 2SC2688(1)-K
TR 2SC2688(1)-L
TR 2SC2688(1)-M
TR 2SC3620(LB-SAN-1)
TR 2SC2621-D-RA
TR 2SC2621-E-RA
TR 2SC2621-C-RA
TR 2SC2688(1)-K
TR 2SC2688(1)-L
TR 2SC2688(1)-M
TR 2SC2621-D-RA
TR 2SC2621-E-RA
TR 2SC2621-C-RA
TR 2SC2688(1)-K
TR 2SC2688(1)-L
TR 2SC2688(1)-M
TR 2SA1037K-T-96-R
TR 2SA1037K-T-96-S
TR 2SA1179-M6
TR 2SA1179-M7-TB
TR 2SA1037AK T146 R
TR 2SA1037AK T146 S
TR 2SA1179N-M6-TB
TR 2SA1179N-M7-TB
TR 2SA1235A1E
TR 2SA1235A1F
Schematic
Location
Part No.
Schematic
Location
Description
RESISTORS
NOTES:
Read description of the Resistor as follows:
(Example)
CARBON
4.7K J A
1/4W
Rated Wattage
Performance Symbols:
A..General B...Non-flammable
Z...Low noise
Other...Temperature coefficient
Tolerance Symbols:
A...0.05% B...0.1% C...0.25%
D...0.5% F...1% G...2%
J...5%
K...10% M...20%
P...+5 -15%
Rated Value, ohms:
K...1,000
M...1,000,000
Material:
CARBON . . . . . . . .Carbon
MT-FILM . . . . . . . .Metal Film
OXIDE-MT . . . . . .Oxide Metal Film
SOLID . . . . . . . . . .Composition
MT-GLAZE . . . . . .Metal Glaze
WIRE WOUND . . .Wire Wound
CERAMIC RES . . .Ceramic
FUSIBLE RES . . . .Fusible
R001
R002
R003
R004
R005
R006
R013
R106
R107
R128
R131
R132
R133
R134
R135
R136
R137
R138
R139
R141
R142
R143
R144
R201
R202
R203
R204
R206
R207
R208
R209
401 256 0101

401 256 0101
401 162 2800
401 162 2800
401 150 5905
401 014 4105
401 027 2600
401 008 2001
401 012 7009
401 255 6005
401 162 3401
401 255 6500
401 150 6209
401 255 6401
401 150 6001
401 256 3805
401 256 6301
401 256 6301
401 162 3609
401 162 4002
401 256 1702
401 150 6209
401 150 6001
401 162 4101
401 150 5905
401 027 5502
401 027 2105
401 162 3005
401 162 3005
401 256 6905
401 256 7100
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
CARBON
CARBON
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
8.2K JA
8.2K JA
1.8K JA
1.8K JA
10K JA
1.5K JA
5.6K JA
18K JA
10K JA
1M JA
39K JA
100 JA
1K JA
3K JA
0.000 ZA
1.5K JA
47K JA
47K JA
470 JA
560 JA
33K JA
1K JA
0.000 ZA
5.6K JA
10K JA
6.8K JA
56 JA
22K JA
22K JA
680 JA
680K JA
1/10W
1/10W
1/10W
1/10W
1/10W
1/4W
1/6W
1/2W
1/4W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/6W
1/6W
1/10W
1/10W
1/10W
1/10W
R276
R281
R287
R288
R289
R353
R405
R406
R411
R412
R413
R414
R417
R421
R422
R423
R426
R428
R471
R472
R481
R482
R485
R486
R487
R488
R489
R491
R492
R493
R494
R495
R497
R499
R503
R504
R505
R506
R507
R508
R509
R511A
R517
R518
R601
R602
R603
R604
R605
R607A
R608
R609
R610
R611
R612
R613
R616
17
Part No.
401 024 9701

401 150 5905
401 255 6500
401 255 6500
401 255 6500
401 024 7400
401 061 6404
401 007 1104
401 053 3206
401 007 4204
401 162 4101
401 024 6700
402 080 3702
401 086 5802
401 052 6802
401 053 2605
401 027 5205
401 025 1902
401 006 7701
401 067 3100
401 010 2600
401 011 9004
401 025 4606
401 065 1801
401 026 6609
401 059 1602
401 066 5204
401 012 5708
401 156 8504
401 019 4001
401 019 4001
401 061 5308
401 068 1600
401 026 6609
401 026 7002
401 027 5502
401 008 4401
401 027 2303
401 006 7602
401 025 4606
401 027 5502
401 065 2808
401 025 4606
401 256 7308
402 083 6106
402 000 1603
402 088 1502
402 090 2108
401 021 5003
401 066 3002
401 021 5003
402 059 4600
401 150 6001
401 150 6100
401 012 5708
401 027 0309
402 001 8502
401 064 1802
401 150 5905
Description
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
OXIDE-MT
CARBON
MT-FILM
CARBON
MT-GLAZE
CARBON
OXIDE-MT
MT-FILM
MT-FILM
MT-FILM
CARBON
CARBON
CARBON
OXIDE-MT
CARBON
CARBON
CARBON
OXIDE-MT
CARBON
OXIDE-MT
OXIDE-MT
CARBON
MT-FILM
CARBON
CARBON
OXIDE-MT
OXIDE-MT
CARBON
CARBON
CARBON
CARBON
CARBON
CARBON
CARBON
CARBON
OXIDE-MT
CARBON
MT-GLAZE
WIRE WOUND
SOLID
RESISTER
RESISTER
CARBON
OXIDE-MT
CARBON
FUSIBLE RES
MT-GLAZE
MT-GLAZE
CARBON
CARBON
FUSIBLE RES
OXIDE-MT
MT-GLAZE
12K JA
10K JA
100 JA
100 JA
100 JA
10K JA
390 JA
1K JA
4.7K FA
120 JA
5.6K JA
100 JA
6.8 JB
2.7K FA
10K FA
3.3K FA
680 JA
15K JA
1 JB
3.9 JA
47 JB
1 JB
18K JA
12 JA
390 JA
15 JA
22 JA
1K JA
33K FA
390K JA
390K JA
39 JA
4.7 JA
390 JA
3.9K JA
6.8K JA
2.7 JA
560 JA
1 JA
18K JA
6.8K JA
120 JA
18K JA
6.8K JA
1 KA
3.3M MA
3.3M JA
3.3M JA
560K JA
2.2 JA
560K JA
22 J0.000 ZA
2.2K JA
1K JA
47K JA
10 J0.39 JA
10K JA
1/6W
1/10W
1/10W
1/10W
1/10W
1/6W
1W
1/2W
1/6W
1/2W
1/10W
1/6W
7W
1/6W
1/6W
1/6W
1/6W
1/6W
1/2W
2W
1/2W
1/4W
1/6W
2W
1/6W
1W
2W
1/4W
1/6W
1/4W
1/4W
1W
2W
1/6W
1/6W
1/6W
1/2W
1/6W
1/2W
1/6W
1/6W
2W
1/6W
1/10W
7W
1/2W
1/2W
1/2W
1/4W
2W
1/4W
1/2W
1/10W
1/10W
1/4W
1/6W
1/2W
2W
1/10W
Schematic
Location
R617
R618
R619
R627
R628
R630
R683
R692
R693
R694
R695
R699
R701
R703
R704
R706
R707
R711
R713
R714
R716
R717
R721
R723
R724
R726
R727
R802
R803
R804
R806
R807
R808
R809
R810
R813
R814
R816
R831
R833
R856
R857
R861
R862
R863
R864
R866
R867
R868
R881
R882
R883
R884
R1008
R1009
R1011
R1012
R1013
R1051
R1052
Part No.
402 092 2007

401 020 0801
401 162 3005
401 150 5905
401 013 5301
401 018 2909
401 162 3708
401 025 4903
401 256 5106
401 024 7400
401 162 3005
401 024 7400
401 025 7409
401 162 2404
401 027 8107
401 009 1508
401 065 4604
401 025 7409
401 162 2404
401 255 9006
401 009 1508
401 065 4604
401 025 7409
401 162 2404
401 027 8107
401 009 1508
401 065 4604
401 162 3005
401 162 3005
401 024 7400
401 162 3708
401 150 5905
401 150 5905
401 162 3708
401 024 7400
401 150 5905
401 150 5905
401 152 3206
401 150 5806
401 024 7400
401 024 6700
401 024 6700
401 026 7408
401 256 5809
401 024 6700
401 256 0200
401 255 6500
401 255 6005
401 026 1000
401 255 6500
401 255 6500
401 024 6700
401 024 6700
401 256 2709
401 255 6500
401 256 1405
401 255 6500
401 256 1405
401 256 2709
401 256 2709
Schematic
Location
Description
FUSIBLE RES
CARBON
MT-GLAZE
MT-GLAZE
CARBON
CARBON
MT-GLAZE
CARBON
MT-GLAZE
CARBON
MT-GLAZE
CARBON
CARBON
MT-GLAZE
CARBON
CARBON
OXIDE-MT
CARBON
MT-GLAZE
MT-GLAZE
CARBON
OXIDE-MT
CARBON
MT-GLAZE
CARBON
CARBON
OXIDE-MT
MT-GLAZE
MT-GLAZE
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
CARBON
CARBON
CARBON
MT-GLAZE
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
MT-GLAZE
MT-GLAZE
CARBON
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
220 J470 JA
22K JA
10K JA
1.2K JA
330 JB
4.7K JA
180K JA
560K JA
10K JA
22K JA
10K JA
220 JA
1.2K JA
82 JA
2.7K JA
12K JA
220 JA
1.2K JA
82 JA
2.7K JA
12K JA
220 JA
1.2K JA
82 JA
2.7K JA
12K JA
22K JA
22K JA
10K JA
4.7K JA
10K JA
10K JA
4.7K JA
10K JA
10K JA
10K JA
330 JA
100K JA
10K JA
100 JA
100 JA
39K JA
270K JA
100 JA
120K JA
100 JA
1M JA
2.7K JA
100 JA
100 JA
100 JA
100 JA
75 JA
100 JA
330K JA
100 JA
330K JA
75 JA
75 JA
1/4W
1/4W
1/10W
1/10W
1/4W
1/4W
1/10W
1/6W
1/10W
1/6W
1/10W
1/6W
1/6W
1/10W
1/6W
1/2W
2W
1/6W
1/10W
1/10W
1/2W
2W
1/6W
1/10W
1/6W
1/2W
2W
1/10W
1/10W
1/6W
1/10W
1/10W
1/10W
1/10W
1/6W
1/10W
1/10W
1/10W
1/10W
1/6W
1/6W
1/6W
1/6W
1/10W
1/6W
1/10W
1/10W
1/10W
1/6W
1/10W
1/10W
1/6W
1/6W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
Part No.
R1059
R1101
R1102
R1103
R1104
R1106
R1901
R1902
R1903
R1904
R1905
R1906
R1907
R1910
R1911
R3401
R3402
R3406
R3407
R3411
R3421
R3422
R3426
401 026 9600

401 255 6500
401 256 1405
401 255 6500
401 256 1405
401 256 2709
401 150 5905
401 150 6209
401 162 2800
401 150 6100
401 256 7605
401 162 4101
401 256 0408
401 024 7004
401 024 7004
401 162 2909
401 162 2909
401 150 5806
401 255 6005
401 265 4008
401 162 3104
401 255 6401
401 256 7605
SW1901
645 006 9673

645 027 7382
645 052 2284
645 006 9673
645 027 7382
645 052 2284
645 006 9673
645 027 7382
645 052 2284
645 006 9673
645 027 7382
645 052 2284
645 006 9673
645 027 7382
645 052 2284
645 006 9673
645 027 7382
645 052 2284
Description
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
470 JA
100 JA
330K JA
100 JA
330K JA
75 JA
10K JA
1K JA
1.8K JA
2.2K JA
3.9K JA
5.6K JA
12K JA
1K JA
1K JA
220 JA
220 JA
100K JA
1M JA
62K JA
3.3K JA
3K JA
3.9K JA
1/6W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/6W
1/6W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
SWITCHES
SW1902
SW1903
SW1904
SW1905
SW1906
SWITCH, PUSH (POWER)

SWITCH, PUSH (VOL +)
SWITCH, PUSH (VOL )
SWITCH, PUSH (VOL )
SWITCH, PUSH (VOL )
SWITCH, PUSH (CH )
SWITCH, PUSH (CH )
SWITCH, PUSH (CH )
SWITCH, PUSH (CH )
SWITCH, PUSH (CH )
SWITCH, PUSH (CH )
SWITCH, PUSH (MENU)
SWITCH, PUSH (MENU)
SWITCH, PUSH (MENU)
TRANSFORMERS
T401
T402
T601
18
610 223 1656

652 000 0703
652 001 2400
645 065 9706
645 056 7360
645 057 8656
DRIVE TRANS
TRANS, DRIVE
TRANS, DRIVE
TRANS, FLYBACK
TRANS, POWER, PULSE
TRANS, POWER, PULSE
Schematic
Location
Part No.
Description
Schematic
Location
CRYSTAL/FILTERS
X141
X201
X801
421 009 9403

610 012 0655
610 204 4195
610 245 9746
645 004 1938
645 004 1945
SAW F TSF5246P
CRYSTAL OSCILLATOR
CRYSTAL OSCILLATOR
CRYSTAL OSCILLATOR
OSC, CRYSTAL 32.768KHZ
OSC, CRYSTAL 32.768KHZ
MISCELLANEOUS
A100
A101
A700
A1901
F601
610 310 6847

645 063 9814
645 063 9821
610 310 6854
645 047 6228
423 007 1601
423 007 1809
423 018 8101
423 029 8008
ASSY, PWB, MAIN G8TCM

TUNER, U/V
TUNER, U/V
ASSY, PWB, SOCKET G8TCM
UNIT, REMOCON RECEIVER
FUSE 125V 4A
FUSE 125V 4A
FUSE 125V 4A
FUSE 125V 4A
F601A
F601B
K701
K1002
K1051
K1101
PS601
Q901
RL601
SP901
SP902
W601
W900
19
Part No.
645 000 5077

645 016 0479
645 000 5077
645 016 0479
645 028 0306
645 038 1904
645 007 1584
645 051 1271
408 046 5209
414 012 3209
645 011 2713
645 015 8629
645 052 5933
652 000 0656
652 000 0656
645 023 1681
645 056 9531
610 306 8282
Description
HOLDER, FUSE
HOLDER, FUSE
HOLDER, FUSE
HOLDER, FUSE
SOCKET, CRT 8P
JACK, RCA-3
SOCKET, DIN 4P
JACK, RCA-3
TH PTDAA1BF3R0Q100
CRT A51QDX992X003
RELAY
RELAY
RELAY
SPEAKER, 8
SPEAKER, 8
CORD, POWER
CORD, POWER-2.0MK
ASSY, WIRE GND
CABINET PARTS LIST

6
5
4
3
2
1
8
9
MENU
CH
- VOL +
POWER
AS
12
11
10
13
ACCESSORY PARTS LIST
CABINET PARTS LIST

KEY NO.
PARTS NO.
1
OR
2
3
OR
4
5
OR
6
OR
7
8
9
10
11
12
13
610 306 5267

610 310 8483
610 268 9648
610 316 5776
412 053 3905
412 054 0002
610 102 7151
610 312 5640
610 312 5657
412 036 1805
411 078 1101
412 018 8402
610 306 5007
610 289 5148
610 299 5527
610 293 2560
610 306 5342
610 306 5311
DESCRIPTION
KEY NO.
CABINET FRONT ASSY

CABINET FRONT ASSY
CRT SPACER 2.0MM (BOT 2)
CRT SPACER 3.5MM (TOP 2)
CRT MTG SCREW M6/35 HI-LO
DC HOLDER (2 USED)
CABINET BACK
CABINET BACK
SCREW 4X14 (7 USED)
SCREW 4X14 (7 USED)
SCREW 3X10 (1 USED)
BUTTON UNIT
CAP RC
DEC SHEET
SANYO BADGE
DEC AV SHEET
DOOR
PARTS NO.
610 312 9143
610 312 9150
610 312 9167
645 065 6910
645 065 6934
610 312 0287
610 312 0317
20
DESCRIPTION
OWNERS MANUAL (ENG)
OWNERS MANUAL (SPA)
OWNERS MANUAL (FRE)
RC TRANSMITTER
RC TRANSMITTER
RC BATTERY COVER
RC BATTERY COVER
B10B10900
NA7D
21
R1007
KB
1
C416
C411
X
C
J406
R1011
KX5P
KX4P
KX3P
T402H4
L413
R498
R407
KX1P
C471
R611
2
Q601H1
Q612
C614
R619
Q613
C612
R614
D613
C613
D603
C604
D884
TP51
D883
X
R602
C606A
C606
A2
R609
R620
R618
R607
R607A
R603
KD
L612
E
R616
J606
J609
J610
D614
R601H2
R601A
R601
Q627
R692
R629
D627
R693
KD2P
L611
D611
R606
C603
R601H3
C683
J690
KD1P
R610
J613
J615
Q611
R617
R608
R604
D604
D602
D601
C693
D693
E Q693
C634
C3436
48
12
13
C3401
C3404
10
R601H1
A1
J608
C3414
C3411
TP301
C011
C010
C3412
C3408
J3404
C601C
J603
E R628
Q681 E
20
C3413
J3403
C3416
LF601
R471
Q601H2
R491
C633A
D471
C633
C493
D699
J605
R485
R493
X
C608A
J005
R492
T601H7
C608
T601H2
R605
C611
T601AH14
J611
J619
J616
C632
R494
T601AH11
T601
L602
D612
J614
2
1
L602A
R635
R612
T601A
C632A
D487
Q402H3
C482
77
R353
D481
L404
R631
R694
Q635
E
R634
R699
Q695
IC601
D351
T401
R405A
R695
R481
T401A
16
Q831
C630
R630
R632
R405
10
16
C629
L3401
40
IC
34
01
24
C3418
R627
D408
L625
J481
TP318
R404
10
L626
C625
D625
R489
J482
C822
C3431
C408
C407
D623
R489A
TJ2
J811
C806
L801
37
25
R3422
R3421
C3417
J3402
C015
D001
IC681A
C800
C1901
C601
F601A
C689
R1901
C601B
J1907
C631A
X X
C631
C1902
D1901
F601B
L1901
C1101
R1103
R1104
C601A
J601
D683
D629 IC681
D680
R686
R691
D1902
D1102
J013
SW1901
Q401
R430
J618
TJ6
C406
R406
C623
L623
L627
TJ5
R487
R499
R884
R3401
C411A
C412A
D624
C624
D486
E R486
D836
D834
J842
R883
R1911
R1910
C3439
C3432
C1007
36
C3427
30
C3424
C003
C001
C002
R1903
J427
D406
C412
R208
C622
C144
J426
D407
J402
R833
Q486
Q005
C626
C489
J843
R683
L812
L811
J809
J808
TP317
IC001
C3422
R408
17
L4
R416
J1013
R005
C416A
R1002
J401
R006
Q001 R832
D490
C829
J831
R813
J872
C811
J806
R013
J804
J868
J867
J866
R868
33
C1006
J3471
C1102
C1103
C006
R003
SW1902
Q402H2
C418
J408
L401A
C628
TJ1
C417A
E
D002
J1011
J1014
L416H2
L401
R106
L416H1
C417
J407
Q402H4
R417
Q490
C012
J014
R488
R517
Q402
L402
J417
C473
C490
J871
J352
D843
R861
R831
R510
C413A
J492
J463
L416
C413
10
J1009
J869
R810
C866
J873
J421
J818
J017
J144
J3401
J016
D472
R1906
POWER
J413
R1004
R468
IC501H1
D503
J416
IC501P
R463
J504
C419
J1058
J861
R495A
C511A
C414A
IC501
D801
R144
C414
J501
J502
C497
J1008
J1007
L414A
J411
R461
C463
J1057
C148
R495
R511A
Q402H1
R1001
J412
J503
C461
J353
J1059
R206
L414
R511
AGC
R464
C466
C462
R816
R814
D831
R497
R1052
J446
J418
J419
C214
IC1001
R209
J863
J817
C802
R882
R881
R497A
K1051
J881
SW1903
C511
K1001
R463A
D482
R1006
C508
C491
R482
K1002
R513
C502
R467
R462
L143
R863
R867
C415
R1008
C501
R503
C503
R518
J462
R138
D806
R141
D461
TP132
D429
R139
J206
R282
R504
R428
R136
L132
C143
C282
J207
R426
C208
X801
D502
D1059
R1009
R472
R512
C1052
C3434
C3433
R509
D501
D1001
R505
SCL
40
32
C421
R423
J801
IC802
C516
D1003
R142
C209
J204
R205
C212
R281
L142
R129
C142
C213
R866
J464
C147
R143
R146
C133
R207
C869
30
R862
R508
R506
D1002
X201
J862
X131
C131
R131
50
C867
J1004
R421
C129
C506
R127
R128
C211
C864
D428
R130 R137
C132 R864
C146
C504
60
R134
C141
C138
C137
64
C427
J1001
J1006
IC801
C868
Q132
J131
TP36
PB
C484
R1051
J814
R804
R3426
C1004
MB
C863
C862
J1002
X141
4
C3426
C1059
R201
R1059
1
L131
R202
C216
J1003
C207
J1056
C136
J1054
20
C403
J813
J802
C401
R411
D421
J803
C861
D1004
TB
C1001
R133
C202
TP35
C1003
C519
C518
R001
J1052
10
R287
C404
J1051
C203
R204
R203
KS
C402
D1052
R132
J202
J201
J807
R807
J1053
C134
Q131
C206
B10B1090A
R289
R288
R857
C201
C204
J203
C810
C808
C807
R808
C801
+
PB
R507
PB
R856
J1081
J461
L141
TP7
C1002
R107
R412
D422
R803
R413
R802
D1051
C102
J142
J141
J143
R276
J146
C1051
C813
D101
SDA
C101
C218
R414
C018
R3407
J414
R1012
R1013
J117
J114
R422
J848
R135
J104
C106
EN
C103
R103
J113
TE7
R806
R809
C809
C3421
C3403
C3402
R3402
R1902
1B
R002
C3423
R3406
SW1904
VOL-UP
60
A101
C004
C3406
C3407
SW1905
R1101
TJ3
PB
R004
R3411
R1907
R1102
SW1906
R1904
PS
IF
K1101
VOL-DN
J021
R1106
C812
CH-UP
KSP
R1905
CH-DN
MENU
L416
J116
COMPONENT AND TESTPOINT LOCATIONS
MAIN BOARD FOIL SIDE
A1901
J1901
PB1
RL601
LF601B
LF601A
PS601
PS601A
C609H1
C609
C609H2
J604
R615
R613
Q601
J622
C884
TP50
D881
T402H11
T402H5
T402H2
T402H7
R1003
T402
T402H8
T402H1
T402H10
T402H9
KY1P
X
KT1P
C883
D882
X
KT2P
X
KT3P
X
KT4P
X
KT5P
CAUTION
4A 125V
FOR CONTINUED PROTECTION AGAINST A RISK OF FIRE,

REPLACE ONLY WITH THE SAME TYPE 4A, 125V FUSE.
ATTENTION : POUR MAINTENIR LA PROTECTION CONTRE
LES RISQUES D INCENDIE UTILISER UN FUSIBLE DE
MAIN BOARD COMPONENTS AND TEST POINTS GRID LOCATIONS

Part
Loc.
Part
Loc.
Part
Loc.
D002
D429
D612
D806
IC001
IC501
IC601
IC681
IC801
IC802
IC1001
IC3401
Q001
C3
E2
B5
E3
F5
D2
C5
C6
F4
F4
E3
E5
D4
Q005
Q131
Q132
Q401
Q402
Q486
Q490
Q601
Q613
Q627
Q681
Q693
Q695
D4
F3
E3
B2
C2
C4
D4
A3
A4
B6
C6
B5
B5
Q831
R512
R513
TE7
TP7
TJ1
TJ6
TP16
TP50
TP51
TP317
TP318
D5
E2
E2
F2
F3
C3
D3
F3
A2
A2
E5
E5
22
D001
4
J016
J017
D472
C1007
C1006
J3471
C1103
C1102
J144
J3401
AUDIO OUT
1
8
IC001
C001
C3427
C3439
C421
R423
D834
D421
20
C212
R833
R832
D490
C490
J871
50
KS
C518
C519
J204
R411
J207
R426
J861
R810
D843
R489
C623
L626
L623
D486
C626
R486
E Q486
R006
Q005
C829
J014
J352
J869
C866
X201
C869
J803
J802
C401
J863
IC801
R489A
L627
D625
E Q490
C012
J872
C811
40
R804 C403
J801
L625
R487
J873
R013
J804
J831
R499
D836
J806
4 IC802
C625
J842
J843
30
J868
J867
J866
J421
33
32
J817
C802
J818
R868
L811
L812
R883
R884
C822
L801
C806
J811
TJ2
J481
L3401
J482
1
R630
J202
J201
R203
R204
C206
R863
C203
10
C211
C148
J1007
J1008
R417
Q001
J1009
C489
C608
C611
J618
L131
J131
X131
L132
R276
TP7
L404
C218
J461
J1081
R856
R857
J1053
J1056
J1054
J1003
J1002
J1006
J1001
R421
J1004
D429
J464
J462
D461
D806
R462
J502
C463
R471
J416
C101
J116
D101
D1051
D1052
J1051
C503
C414A
C413A
J104
C106
R507
R505
C415
R482
C484
R497
D482
R497A
R408
C416
C418
Q402H1
D502
C416A
R511
C417A
J427
V-ADJ.DOWN
R1059
D1004
J1052
C1051
J113
C102
C1003
C1004
R508
R504
R509
V-ADJ.UP
IC501
R512
C502
J412
J411
R511A
J426
C417
H-OUT
C413
C414
J501
J503
C508
Q402
Q402H2
C412A
C411A
R506
J117
R107
J504
C501
C516
D501
C1002
TUNER
C1001
C1059
C506
C466
L401
D407
J408
C412
D406
C411
J406
C504
J114
R428
D428
R464
R461
10
L402
J407
R406
C406
R430
Q401
R404
R491
C493
R485
D487
D351
R353
R481
D408
L401A
D503
R468
IC501P
C461
R463A
R422
J848
R405A
TE7
C407
IC501H1
C408
R106
L141
J142
J143
J141
C497
L143
L142
R414
J419
D801
J463
J492
J1011
J1014
R494
R493
R492
D471
C471
D481
C482
R405
DIP
J402
J401
D002
J417
C473
J1013
J353
J446
J418
R412
Q132
C201
Q131
64
E
C419
C143
E
C134
C204
D422
60
C141
J206
C213
J1058
C214
J1057
J1059
C628
C624
C622
D624
D623
10
10
C015
5
C002
C3424
C3418
C3417
J3402
C3416
C3413
J3403
C3436
R699
R612
C608A
R611
Q601H1
TUNER
C010
C011
C3411
C3408
C3404
C3401
C629
IC601
3
R694
T601A
D699
L416
J013
C3414
C3412
J3404
C1101
C634
R1910
R1911
C3432
J809
J808
C693
16
16
L602A
Q611
D611
L611
C511A
R510
C511
J413
23
C1901
C683
D693
Q695
C630
1
L602
T601
R604
R617
R606
R610
L612
Q612
KX
D1102
D1902
Q681
J690
R692
E
R631
R603
R605
J614
3
J616
D614
R607
J606
D613
R614
C614
KB
R467
1
X141
4
C633A
B10B10900
NA7D
KX5P
KX4P
K1051
KY1P
TJ3
J1907
IC681
E
D629
D680
Q627
R601H3
C603
C604
R607A
C613
C612
Q613
L417
L416
K1101
IC681A
R686
60
1B
L1901
Q693
R634
D601
D602
D604
D603
R618
T402H1
K1001
K1002
HLC
R495
AV
T402H10
Q635
R601H2
C606A
L413
T402H9
E
D627
R601A
A2
C606
R602
R513
T402H7
R495A
A101
KT3P
KX3P
KX1P
????
R628
R601H1
R601
A1
LF601
J608
C601
T402H2
T402H8
J601
D683
C601C C601B
Q402H4
CLK
B
T402H4
T402H5
T402H11
C1902
C631A
C601A
FBT
KTP
L416H1
V-OUT
T401
Q402H3
R498
R488
TJ5
T601H2
TJ6
L416H2
C633
Q601H2
KY
F601A
KT5P
T402
TP50
ACK
T601H7
R615
TJ1
POWER-TRANS
Q601
B10B1090A
KT1P
GND
T601AH14
L414A
NA7D
T601AH11
R635
L414
R613
C632A
X801
POWER-CIRCUIT
C632
C609H1
D1901
C631
F601B
PS601A
R472
C609
D612
C609H2
KD1P
KD2P
R463
KT4P
R407
STA
TUS
KD
4A 125V
MTS
4A-125V
SW1905
SW1902
F-AV
KSP
1
SW1904
SW1903
SW1901
RL601
T401A
KT2P
PS601
SW1906
CH-DN
MENU
CH-UP
VOL-UP
VOL-DN
POWER
A1901
TP301
LF601B
LF601A
HDT
TP51
DATA
PS
COMPONENT AND TESTPOINT LOCATIONS (Cont.)

MAIN BOARD PARTS SIDE
PICTURE TUBE SOCKET BOARD
C702
R701
B10B1090B
Q701A
R717
R704
R707
K7B
D1902
R706
Q701
(-)
9V HEATER +B
L701
R727
R716
R726
????
K7U1
SCREEN
Q721
Q721A
C742
K701
R711
R721
R724
E
Q711
Q711A
K7S
5 (-) (-)
GND
K7Y1
G R1
PIC TUBE SOCKET BOARD COMPONENTS

Part
Loc.
Q701
Q711
Q721
N/A
N/A
N/A
For parts or service contact

SANYO Fisher Service Corporation
21605 Plummer Street
Chatsworth, CA 91311 (U.S.A.)
300 Applewood Crescent,
Concord, Ontario L4K 5C7 (CANADA)
April / 2004 / 2000 SMC
Printed in U.S.A.
24
MODEL DS20930
Chassis No. 20930-06
WAVEFORMS
CAUTION
SCHEMATIC DIAGRAMS

ATTENTION: POUR MAINTENIR LA PROTECTION
CONTRE LES RISQUES D' INCENDIE UTILISER UN
FUSIBLE DE RECHANGE DE MEME TYPE 4A, 125V.
BLOCK DIAGRAM
4A 125V
NOTES ON SCHEMATIC DIAGRAMS

1. All resistance values in ohms K=1,000 M=1,000,000.
2. Unless otherwise noted on schematic, all capacitor values less than 1 are expressed in F (Micro Farad),
and the values more than 1 are in pF.
3. Unless otherwise noted on schematic, voltage reading taken with VOM from point indicated to chassis
ground. Voltage reading taken using color-bar signal VHF channel 5, all controls at normal. Line voltage at 120
volts. Some voltages may vary with signal strength.
4. Waveforms were taken with color-bar signal and controls set for normal picture. Waveforms marked with
an may vary with signal strength.
5. The Symbol
indicates a fusible resistor, which protects the circuit from possible short circuits.
Note: Voltages were measured with offset color-bar signal and controls set for normal picture.
SDL
SCL
ANT
64
IF
A101
UHF/VHF TUNER
WITH PLL
& BAND SW
61
AGC
VIDEO
DET.
60
56
VIDEO
AMP.
VIDEO
SW.
FM
DET.
IC1001
AV SW
54
THE COMPONENTS DESIGNATED BY A STAR () ON THIS SCHEMATIC DIAGRAM DESIGNATE COMPONENTS

WHOSE VALUES ARE OF SPECIAL SIGNIFICANCE TO PRODUCT SAFETY. SHOULD ANY COMPONENT
DESIGNATED BY A STAR NEED TO BE REPLACED, USE ONLY THE PART DESIGNATED IN THE PARTS LIST. DO NOT
DEVIATE FROM THE RESISTANCE, WATTAGE AND VOLTAGE RATINGS SHOWN.
1 V1 IN
AUDIO IN-2 (L)
FM
AMP.
23
AV1/2S
24
MUTE
39
32
46
S-Y IN
BUS SDA
31
45
C IN
SW1901-1906
CONTROL KEYS
KEY IN
36
A1901
RC PRE-AMP
RC IN
26
IIC SCL
28
37
ABL IN
27
10
ACL IN
IC802
EEPROM
IIC SDA
Q001
POWER OFF
NOISE
CANCEL
AUDIO IN-1 (L)
RESET
PHOTO COUPLERS
ABL
L
V
H-PULSE
44
TOP VIEW
EC
EC
EC
B
E
IC501
VERT.
OUTPUT
17
V-DRIVE
15
E/W
5
1
6/7
T402
HORIZ.
OUTPUT
TRANS.
SIDE VIEW
BC
EC
TOP VIEW
C
B ... BASE
1
12
32
OUT
GND
IN (2) (3)
(1)
C ... COLLECTOR
E ... EMITTER
B
INFRARED EMITTING
B ... BASE
C ... COLLECTOR
E ... EMITTER
CHIP TRANSISTORS
E
BC
Q401
HORIZ.
DRIVE
H-DRIVE
47
L901
DEGAUSING
COIL
AC120V
60Hz
25
HOLD DOWN
T601
CONVERTER
TRANS.
D623
LF601
LINE
FILTER
A....ANODE
K....CATHODE
C601
D625
Q613
ERR.
AMP.
TOP VIEW
12 x 10 3 = 12K ohm
D624
D612
PHOTO
COUPLER
CHIP RESISTORS
4A 125V
13
14
K1011
FRONT
AV IN
(AV 1)
8
4
Q721
-R OUT
Q711
-G OUT
Q701
-B OUT
IC001
AUDIO
AMP. 3
SP901
LEFT
SPEAKER
Q132-E (TP16)
(Internal Video)
Q401- B
(Horizontal Drive)
48 VERT
0.6V VERT
1.0V HORIZ
.7V HORZ
Q402- B
(Horizontal Output)
Q601- G
(Power Switching)
T402- 9
(Heater)
21V HORZ
15V 50KHz
28V HORIZ
SP902
RIGHT
SPEAKER
ABL
H.V.
FOCUS
SCREEN
HEATER
LOW +B
D482
HOLD DOWN
DETECT.
Q901
PIX TUBE
D481
+200V
POWER ON/OFF
IC681
5V REG.
Q681
12V SW
DRIVE
+130V
D471
AUDIO +B
15V
+30V
IC601
POWER
REG.
D601-D604
FULL WAVE
RECTIFIER
D806
TJ1
Q601
SW.
12
Q402
HORIZ.
OUTPUT
29
POWER
FAIL
PS601
POSISTOR
F601
AC
FUSE
RGB
DRIVE
CUT/
OFF
I/O
PORTS
RL601
RELAY
K
K
A
33
CLOCK
CONTROL
21
X 801
X OUT
H
DRIVE
34
+12V
1
COUNT TERMINALS IN
ARROW DIRECTION
X IN
MARK
C809
C808
TOP VIEW
DEFLECTION
YOKE
L902
H-PULSE
5
40
V
DRIVE
DIODES
TRANSISTORS
IC501- 1
(Inverting Input)
AUDIO +B
T401
H-DRIVE
TRANS.
INTEGRATED CIRCUITS
IC501- 5
(Vertical Output)
AUDIO IN-1 (R)
Q831
RESET
1.0V HORIZ
VIDEO IN-1
Q005
AUDIO +B
SWITCH
VIDEO
MATRIX
SYNC
SEP.
THIS TV CONTAINS CRITICAL PARTS TO PROTECT AGAINST X-RADIATION. NOMINAL 2ND ANODE VOLTAGE IS
29.1KV AT ZERO BEAM CURRENT AT 120 VOLTS AC LINE, AND MUST NOT EXCEED 31.1KV UNDER ANY
OPERATING CONDITION. SEE HIGH VOLTAGE CHECK ON PAGE 9.
4.0V HORIZ
Q131
BUFFER
X-RADIATION WARNING NOTE
K1001
REAR
AV IN
(AV2)
VIDEO IN-2 (R)
S-SW
I/O
PORTS
3.8V HORIZ
VIDEO IN-2
3 V2 IN
BUS SCL
4.0V HORIZ
K1051
S-VIDEO IN
SERVICE NOTES:
1. When replacing parts on circuit boards, clamp the lead wires to terminals before soldering.
2. When replacing high wattage resistors on circuit board, keep the resistor body 10 mm (3/8) from circuit board.
3. Keep wires away from high voltage and high temperature components.
IC801- 54
(Video Input)
Y
C
S-SW
Q132
BUFFER
63
IC801- 14
(B-Output)
3 LS OUT-R
33 34 36 37
13
TP16
X141
SAW
FILTER
IC801- 13
(G-Output)
4 LS OUT-L
IC3401
MTS DECODER
IC801- 12
(R-Output)
5V
ALWAYS
D002
POWER FAIL
12V
D627
+12V
Q635
OVERLOAD
PROTECT.
Q486
9V REG.
Q627
12V SW.
Q490
5V REG.
Q693,
Q695
STANDBY MODE
ALWAYS +5V
CONTROL
D801
9V
TJ5
D428
(13V)
D429
ANODE LEAK
DETECT.
(7V)
5V
B6
R428
g8tcm
123
VOLTAGE CHARTS
NOTE: Voltages were measured using color-bar signal and the controls set for normal picture.
Device/Pin #
D612-1
CAPACITOR AND RESISTOR CODE CHART

D612-2
CAPACITOR (Example)
D612-3
500 C K 1500 B
D ...........................
T ............................
J ............................
K ...........................
M ...........................
N ...........................
P ...........................
Z ...........................
C ...........................
C ...........................
E ...........................
F ...........................
N ...........................
T ............................
K ...........................
H ...........................
P ...........................
M ...........................
Characteristics
Value code
Tolerance code
Material code
Voltage rating
0.5pF
+50% 10%
5%
10%
20%
30%
+100% 0%
+80% 20%
0.25pF
Ceramic
Electrolytic
Polyester
Polypropylene
Tantalum
Ceramic
MT-Composite
NP. Electrolytic
MT-Polypropylene
RESISTOR (Example)
6 Y K 4.7
D ...........................
F ...........................
G ...........................
J ............................
K ...........................
M ...........................
F ............................
N ...........................
S ...........................
Y ...........................
C ...........................
D ...........................
W ..........................
Value code
Tolerance code
Material code
Wattage rating
25
0.5%
1%
2%
5%
10%
20%
Fusible
Metalized Carbon
Oxide Metalized
Wire Wound
Solid
Carbon Film
Wire Wound
D612-4
IC001-1
IC001-2
IC001-3
IC001-4
IC001-5
IC001-6
IC001-7
IC001-8
IC501-1
IC501-2
IC501-3
IC501-4
IC501-5
IC501-6
IC501-7
IC601-1
IC601-2
IC601-3
IC681-1
IC681-2
IC681-3
IC801-1
IC801-2
IC801-3
IC801-4
IC801-5
IC801-6
IC801-7
IC801-8
IC801-9
IC801-10
IC801-11
IC801-12
IC801-13
IC801-14
IC801-15
IC801-16
IC801-17
IC801-18
IC801-19
IC801-20
IC801-21
IC801-22
IC801-23
Device/Pin #
Volts/Mode
POWER ON:
25.7
POWER ON:
24.8
POWER ON:
0.7
POWER ON:
14.7
6.0
13.2
5.6
GND
N.C.
1.4
1.4
GND
GND
14.3
29.5
2.9
2.9
29.2
2.8
130.0
28.3
GND
13.4
GND
5.0
2.5
2.5
3.2
2.4
2.2
2.2
2.2
5.1
2.5
9.2
8.1
2.3
2.4
2.6
2.2
2.2
2.3
1.7
5.1
2.7
0.5
GND
.04
POWER OFF:
9.6
POWER OFF:
8.0
POWER OFF:
0.4
POWER OFF:
1.7
IC801-24
IC801-25
IC801-26
IC801-27
IC801-28
IC801-29
IC801-30
IC801-31
IC801-32
IC801-33
IC801-34
IC801-35
IC801-36
IC801-37
IC801-38
IC801-39
IC801-40
IC801-41
IC801-42
IC801-43
IC801-44
IC801-45
IC801-46
IC801-47
IC801-48
IC801-49
IC801-50
IC801-51
IC801-52
IC801-53
IC801-54
IC801-55
IC801-56
IC801-57
IC801-58
IC801-59
IC801-60
IC801-61
IC801-62
IC801-63
IC801-64
IC802-1
IC802-2
IC802-3
IC802-4
IC802-5
IC802-6
IC802-7
IC802-8
IC1001-1
IC1001-2
IC1001-3
26
Volts/Mode
1.5
4.9
0
0
0
4.8
4.9
4.1
4.0
1.9
2.6
4.9
0
0
1.8
4.9
4.9
3.3
GND
0
1.2
2.5
2.6
0
2.6
0.3
2.8
0.3
5.0
3.5
2.6
5.0
2.5
2.6
2.3
2.8
2.4
1.8
GND
2.8
2.8
GND
GND
GND
GND
0
0
GND
5.0
2.5
0
2.5
Device/Pin #
IC1001-4
IC1001-5
IC1001-6
IC1001-7
IC1001-8
IC3401-1
IC3401-2
IC3401-3
IC3401-4
IC3401-5
IC3401-6
IC3401-7
IC3401-8
IC3401-9
IC3401-10
IC3401-11
IC3401-12
IC3401-13
IC3401-14
IC3401-15
IC3401-16
IC3401-17
IC3401-18
IC3401-19
IC3401-20
IC3401-21
IC3401-22
IC3401-23
IC3401-24
IC3401-25
IC3401-26
IC3401-27
IC3401-28
IC3401-29
IC3401-30
IC3401-31
IC3401-32
IC3401-33
IC3401-34
IC3401-35
IC3401-36
IC3401-37
IC3401-38
IC3401-39
IC3401-40
IC3401-41
IC3401-42
IC3401-43
IC3401-44
IC3401-45
IC3401-46
IC3401-47
IC3401-48
Volts/Mode
0
0
5.0
1.8
GND
4.1
4.1
4.1
4.1
3.6
3.7
GND
4.1
4.1
4.1
4.1
4.9
4.1
1.3
1.3
0
GND
3.2
9.1
0
4.1
4.1
3.7
3.9
4.1
4.1
4.1
1.9
4.1
4.1
2.0
4.1
4.1
4.1
0
4.1
4.1
4.1
4.1
4.1
4.1
GND
4.1
4.1
4.2
GND
4.1
4.1
Device/Pin #
Q001-B
Q001-C
Volts/Mode
POWER ON:
0.7
POWER ON:
Q001-E
Q005-B
Q005-C
Q005-E
1.9
GND
13.4
14.0
14.0
Q131-B
Q131-C
Q131-E
Q132-B
Q132-C
Q132-E
Q401-B
Q401-C
Q401-E
Q402-B
Q402-C
Q402-E
Q486-B
Q486-C
Q486-E
Q490-B
Q490-C
Q490-E
2.2
9.2
1.5
1.2
GND
1.9
0.3
52.1
GND
0
130
GND
9.9
11.6
9.2
5.9
6.7
5.2
Q601-G
Q601-D
Q601-S
Q613-B
Q613-C
Q613-E
Q627-B
Q627-C
Q627-E
Q681-B
Q681-C
Q681-E
Q693-B
Q693-C
Q693-E
POWER ON:
5.8
POWER ON:
157
POWER ON:
.9
POWER ON:
0.3
POWER ON:
4.7
GND
POWER ON:
12.7
POWER ON:
13.2
POWER ON:
13.3
POWER ON:
0.7
POWER ON:
0
GND
POWER ON:
0.5
POWER ON:
27.4
POWER ON:
0.6
Device/Pin #
POWER OFF:
0
POWER OFF:
Q695-B
Q695-C
17.0
Q695-E
Q701-B
Q701-C
Q701-E
Q711-B
Q711-C
Q711-E
Q721-B
Q721-C
Q721-E
Q831-B
Q831-C
Q831-E
Volts/Mode
POWER ON:
27.4
GND
POWER ON:
27.5
2.4
154.9
2.2
2.4
158.0
2.2
2.3
159.0
2.2
4.2
4.9
4.9
POWER OFF:
7.4
POWER OFF:
8.0
POWER OFF:
0.4
POWER OFF:
164
POWER OFF:
0
POWER OFF:
0.1
POWER OFF:
0.1
POWER OFF:
8.0
POWER OFF:
0
POWER OFF:
8.0
POWER OFF:
0
POWER OFF:
6.0
POWER OFF:
5.2
POWER OFF:
7.1
POWER OFF:
4.7
27
28

REMOTE SENSOR
TP11
R1910
1K
C1902
16EM10
LBWA
C148
6.3EM100
LBWA
R106
1/2DJ18K
C862
CJ18CL
C866
16EM47
LBWA
28
29
30
31
32
1/10GJ 1MC
R861
1/10GJ
39KC
C403
PM1
LBZA
<STATUS>
R488
1SJ15
TP318
TP317
37
36
38
39
29
VETC
28
VE
SAPIN
C3423
10TK3.3DR
C3422
KK0.047LZB
R3422
1/10GJ3KC
R3421
1/10GJ3.3KC
C3421
KK2700
LZB
C011
16EM470LBWA
C3414
16EM220
LBWA
C010
16EM470LBWA
R472
2SJ3.9
C3416
PM4.7
LBZA
15V
AUDIO AMP.
IC001
LA4525
Q005
2SB764E
:2SB764F
R005
1/10GJ10KC
AUDIO MUTE
9V-REG.
C006
KK0.01LZB
C511
FK0.22BF
:HJ0.22G
KX3P
DY
ITC(CRT COMPONENT)
R513
X
KX1P
<ABL>
<ACL>
R508
18K
C504
25EM2200
LBWA
C503
EK2.2AE
R505
1/2DJ
2.7
R699
10K
D680
R
1000KK
1200CTB
:1000KK
1200CRD
B1
Q695
2SA1015Y
:2SA564ARCU
:2SA608FCNP
R695
1/10GJ
22KC
D699
C630
EM1LBWA
R406
1/2DJ1K
R417
7SJ6.8VC
R701
220
K7S
R706
1/2DJ2.7K
KB
C471
16EM470
LBWA
D471
R471
1/2DJ
11
2
2SJ4.7
3
R703
1/10GJ1.2KC
C701
CJ270CL
CRT
Q901
C614
63FJ0.01
LBZA
R686
J
R482
DJ1B
D482
R423
1/6NF
3.3K
D481
ES1
R421
1/6NF
2.7K
LETTER
SIDE
TOP VIEW
2SC1740S
HOLD DOWN CIRCUIT

TP7
R422
1/6NF
10K
D422 D421
HZ11
HZ11
B2L
B2L
C421
6.3EM
220LBWA
P (7DD00021) 1S2076A,1S2471, 1N4148

9. LIST OF REPLACEABLE TRANSISTORS.
6. VIEW OF TR & FET & IC.
R428
15K
AA (7DD00192) 1S2076, 1S2473, DS442, 1N4148, 1SS133
ARE RELATED WITH X-RADIATION.
5. THICK LINES ARE 15WATTS SUPPLY LINE.
C484
EM4.7
LBWA
TE7
D428
HEATER
11
R497
D429
R
AFC
10
1B
R287 1/10GJ100C
R288 1/10GJ100C
R289 1/10GJ100C
LOW +B
8
C482
100EM22
LBWA
R726
1/2DJ2.7K
R716
1/2DJ2.7K
V+B
C493
100PM
2.2X
EC
7. ISOLATION BORDER LINE.

COLD SIDE
KS
GND
HOT SIDE
B
B
EC
E
BC
3
1 2 S
GD
IN CASE
OF TR
IN CASE
OF IC
IN CASE
OF FET
AD (7T200183)
Q,R,S
AE (7QT00202)
Q,R,S
2SC945A
Q,P
AC (7T200182)
O,Y,GR
2SA564A
R
Q,R
Y,GR
R,Q,P
2SA933S
AB (7T200181)
R
Q,R
2SC1815
2SA1015
Y,GR
O,Y,GR
10. "J" : JUMPER WIRE.

"X" : PART NOT USED.
IMPORTANT:
SCHEMATIC PART LOCATION NUMBERS MAY NOT ALWAYS MATCH THE SCHEMATIC SYMBOLS.
THE SCHEMATIC SYMBOLS AND PART DESCRIPTIONS ARE CORRECT AND SHOULD BE USED.
THE PART DESCRIPTIONS WILL BE LISTED UNDER THE LOCATION NUMBER IN THE PARTS LIST.
R704
82
B-OUT
Q701
R481
1/2DJ
47B
<B>
15V
4. PARTS MARKED WITH
C711
CJ270
CL
R619
1/10GJ
22KC
R (7DD00019) 1S2076, 1S2473, DS442, 1N4148
3. ALL CAPACITORS ARE 50WV RATING UNLESS OTHERWISE NOTED.
10
R493
DJ560K
<G>
R711
220
TP51
R494
DJ560K
3
9V
5
R491
DJ1K
TP50
K701
12V
M (7ED00025) 1SS176, 1SS133, GMA01
AND RESISTANCE VALUE ARE "1/4".
SOCKET
D683
R
R616
1/10GJ
10KC
8. LIST OF REPLACEABLE DIODES.
2. RESISTORS SPECIFIED WITH TYPE OF RESISTOR, TOLERANCE
C721
CJ270
CL
G-OUT
Q711
R713
1/10GJ
1.2KC
2000KZ
1000HE
D613
R617
FJ
220P
NOTES;
1. RESISTORS SPECIFIED WITH RESISTANCE VALUE ARE "1/6DJ".
TP35
C613
63FJ
6800LBZA
POWER REG.
IC601
SE130NH
D693
K7Y1
GNDCONNECTOR
W900
29
30
31
KD
R602
1/2CM
3.3MXU
:1/2XJ
3.3MVA
:1/2XJ
3.3MVCA
F.B.T
T402
500KK
1000A
SC
C742
C406
TP36
R721
220
R714
1/10GJ82C
FO
3
K7U1
R723
1/10GJ
1.2KC
R727
2SJ
12K
R-OUT
Q721
R724
82
500KK
3900A
<R>
2SJ
12K
Q701/Q711/Q721
2SC2621CRA
:2SC2621(DRA:ERA)
:2SC2688'1'(K:L:M):QT0229Z
C407
HV
K7B
L701
R707
2SJ
12K
63FJ0.1LBZA
Q401
2SC3332R
:2SC3332S
R717
ASSY,PWB,SOCKET G8TCM
J606
J
RELAY DRI.
Q693
AE
R693
1/10GJ
560KC
R404
J
J426
J
C473
HJ0.47G
:63GJ0.47
LBZA
C408
35EM47LBWA
R618
DJ470
C632
250KM
1000VBBW
AC CORD
KD2P
D614
Q613
2SC3069
R694
10K
R692
180K
C693
KY1P
1/2FJ
22
W601
KD1P
J611
1/10GZ0C
R614
J
A2
R607A
R609
1/10GJ
2.2KC
PS601
RL601
J616
J
D612
C601
275GM0.22VDC
R610
DJ1K
L602
16
T401
L401
J
L402
J
2SJ
0.39
D604
D603
J619
1/10GZ
0C
J615
1/10GZ 0C
A1
F601A
R608
1/10GZ0C
J613
1/10GZ 0C
C625
D611
J
R613
D408
J408
J
D625
C628
160EM
220XJ
:160EM
220VEA
R630
DJ 330B
Q402
TXXGA
0137505M
14
L625
1SJ390
H-OUT
R507
1/2DJ1
130V
TJ1
R611
47K
11
<B>
<G>
<R>
<X-RAY>
<POWER FAIL>
130V
R405
R504
6.8K
R506
560
HORIZONTAL DEFLECTION
<H-PULSE>
R503
26V
<H-DRIVE>
C506
63FK5600
R509 LBZB
6.8K
R512
X
C416
250MJ0.27AP
:250MJ0.27AU
:250MJ0.27AY
C411
1500MH7200XK
:1500MH7200AN
C508
CJ56G
B1
C683
16EM100
LBWA
R502TM
3.9K
C516
EM10LBWA
KX4P
C501
35EM
470LBWA
<V-OUT>
<E/W>
VCC
6
IN
OUT
2
GND
2SJ120
R628
DJ1.2K
Q681
AE
C502
35EM220
LBWA
D501
C626
16EM1000
LBWA
R606
J
2SK2638 F82 R612

1/2FJ10
L623
L627
R627
1/10GJ
10KC
R683
1/10GJ
4.7KC
L404
J
Q601
D624
10
C629
16EM220
LBWA
C608
1000KK
1000NH
F601
LF601
F601B
R603
DJ560K
R605
DJ560K
5
13
C622
35EM1000
LBWA
Q627
2SB985S
:2SB985T
:2SA1707S:2SA1707T
D601
C612
63FJ3300
LBZA
R884
KT5P
KT4P
KT3P
KT2P
KTP
KT1P
1
R511A
KX5P
R492
1/6NF33K
TJ2
J427
J
ASSY, PWB, MAIN G8TCM

FOR TEST EQUIPMENT
<POWER ON/OFF>
9V
2SJ2.2
L626
J
D623
26V
100
100
R883
R882
R881
D806
R
D502
12
D602
200EM330XG
:200EM330XL
R604
1 2 3
IC681
PQ050EA1MXP
<POWER FAIL>
R518
1/10
GJ
6.8KC
TJ3
26V
C609
5 VOLTS REG
5V
12V
<R>
7WK1VEA
T601
<B>
<G>
R601
<ALWAYS +5V>
1/10GJ100C
1/10GJ100C
<V-OUT>
D002
R
C631
250KM
1000VBBW
:250KM
1000VBW
R487
390
D486
R485
18K
R006
DJ1.5K
R013
5.6K
<DATA>
D487
SP902
1.0W 10Z
C012
EM1LBWA
2SJ12
Q486
2SD400E-MP
:2SD400F-MP
<CLK>
R517
1/10
GJ
18KC
4 4
C015
16EM330
D472
LBWA
R489
2SJ22
R486
<ACL>
26V
SP901
C3418
PM4.7
LBZA
C003
KK5600
LZB
C001
EM0.22
LBWA
SPEAKER OUT
Q001
AE
<SIF>
R276
12K
KSP
1 1 1
<POWER FAIL>
LA7841
REAR A/V (AV2)
35
34
33
32
31
40
43
SURRTC
TVOUT-L
TVOUT-R
AUX2-L
30
C3424
PM4.7
LBZA
9V
TJ5
IC501
FRONT A/V (AV1)
C3433
KK4700
LZB
C3434
KK0.022
LZB
VEOUT
C004
KK5600
LZB
R004
1/10GJ
1.8KC
R003
1/10GJ
1.8KC
TP34
R499
390
D490
VCAIN
C3426
10TK10DR
C002
EM0.22LBWA
R001
1/10GJ8.2KC
R495
1SJ39
C497
16EM47
LBWA
C218
16EM47LBWA
VCATC
R3426
1/10GJ3.9KC
C3427
EM1LBWA
C3417
25EM4.7
LBWA
C3413
25EM4.7
LBWA
C3412
16EM47
LBWA
R002
1/10GJ8.2KC
Q490
2SD400E-MP
:2SD400F-MP
VCAWGT
R3411
1/10GF
62KC
TP301
TJ6
AUX1-R
VEWGT
C3411
EM0.47
LBWA
L811
D801
R
Video
L3401
J
C3408
EM0.47
LBWA
L812
5V
41
PCINT1
PCINT2
PLINT
TRE-R
MAINOUT
NC 42
MAININ
27
L
4
26
C402
KK0.01
LZB
25
24
R414
100
R411
1/6NF4.7K
23
DGND
IC3401
CXA2134QP
NC
AUX1-L
22
C3406
KK0.012
LZB
C3407
KK5600
LZB
R802
1/10GJ22KC
R803
1/10GJ22KC
R804
10K
R806
1/10GJ4.7KC
21
R1104
1/10GJ
330KC
20
R412
1/2DJ
120
R133
1/10GJ
1KC
19
R204
56
5VB6
18
R201
1/10GJ
5.6KC
R202
1/10GJ
10KC
C207
KK0.01
LZB
R203
6.8K
R135
1/10GJ75C
17
C518
63GJ0.47
LBZA
C201
16EM100
LBWA
TP21
16
15
R1103
1/10GJ
100C
14
<H-PULSE>
13
IIC SDA
12
REMOCON IN
11
C203
16EM10
LBWA
C204
EM3.3
LBWA
C206
16EM220
LBWA
10
HOR
OUT
C401
10EM330
LBWA
R413
1/10GJ
5.6KC
IF Vcc
9
C216
KK0.01
LZB
C202
KK0.01
LZB
Q131
AE
R134
1/10GJ
3.3KC
R132
1/10GJ100C
R131
1/10GJ
33KC
C136
CJ150CL
C138
KK0.01
LZB
C137
KK1000
LZB
4
C134
EM1
LBWA
3
C133
1/10GZ0C
C132
KK0.022
LZB
C131
CJ10CL
HOR
VCC
V/Y
SW
E/W
[952]
SCL
R3407
R868
2.7K
DC
VOL
RGB Vcc
FM
AMP
BPF
POWER FAIL
/ACK
VER
RAMP
MEMORY
IC802
C_SYNC
PHASE
SHIFTER
MUTE
SW
VER
C/D
DRIVE
/CUT-OFF
AV1/2
ABL
ACL
SDA
C3404
PM4.7LBZA
R3406
1/10GJ
100KC
DATA
I/O
PORT I
R1102
1/10GJ
330KC
27
AFC2
LSOUT-L
VER
SEP
LSOUT-R
FS
I
R1101
1/10GJ
100C
26
FBP
BUS SCL
0SD
SW
R3402
1/10GJ
220C
8
AFC1
CONTRAST
BRIGHT
C404
KK6800LZB
FM
DET
C806
6.3EM220
LBWA
ADC
BUS SDA
0SD
CONTRAST
R3401
1/10GJ220C
CLOCK
500K
DET
TIMER
0
25
CLOCK
CONTROL
BUS
STATUS
SPLL
OSB
G
SYNC
SEP
C802
16EM47
LBWA
C801
KK0.01
LZB
BASS-L
C1103
25EM4.7
LBWA
24
OSD
VM
[952]
LIM
AMP
RAM
HS
R
SOUND
DET
ROM
R807
1/10GJ
10KC
22 STIN
NOISETC
SAPOUT
23
HS
VS
R808
1/10GJ
10KC
C1102
25EM4.7
LBWA
AUX2-R
21 SUOUT
ENABLE
VS
HOR
C/D
COLOR
CLAMP
BASE
TIMER
RGB
MATRIX
BS
SG
CPU
CORE
20 NC
BUS
DL
SHARP
V/Y
SW
L801
PDC
TOUT-L
19 VCC
1/256
44
TINT
CVBS
TRAP
C3436
PM4.7
LBZA
C3401
EM0.1
LBWA
CPU TST B
TOUT-R
HOR
VCO
K1101
2
R1 IN
CPU TST G
SW
VC0
VIDEO
DET
BPF
AUDIO PROCESSOR
DEM0
ACC
R1106
1/10GJ
75C
C829
EM1LBWA
D834
R809
1/10GJ4.7KC
BPF
DC
REST
VIF
AMP
D836
R
CPU TST R
POWER
TRAP
R833
10K
R831
1/10 GJ
100KC
VOLIN-R
RESET
L1 IN
I/O
PORT 0
AFT
DAH
YC SW
IF
AGC
CLOCK
CONTROL
RST
18 SAPTC
VDD
V DET
RESET
VIDEO
SW
SN
PLL
17 GND
X-RAY
45
CLMP
DC ADJ
VX0
46
APC1
BASS-R
AFT
FSC
SYNC
CLMP
16 NC
CLMP
IIC SCL
VIDEO
AMP
RF
AGC
15 IREF
IC801
D831
C3439
PM4.7
LBZA
<ALWAYS 5V>
Video/V
Vcc
QXXAVC367
UOC LA76950
V1 IN
C3432
EM0.1
LBWA
R816
1/10GJ
330C
C3431
KK4700
LZB
33
47
34
VOLIN-L
TRE-L
NC
35
48
36
R862
1/10GJ
270KC
KEY IN
C864
KK0.01
LZB
37
COMPIN
14 VGR
38
39
ABL IN
RF AGC
X801
40
41
42
R863
100
C868
KK0.033
LZB
43
44
45
46
47
48
10
49
11
50
R1013
1/10GJ
330KC
C1101
EM2.2
LBWA
R814
1/10GJ
10KC
12
51
C863
CJ18CL
R864
1/10GJ
120KC
C869
EM2.2
LBWA
R866
1/10GJ
100C
D351
R281
1/10GJ10KC
C427
KK0.01LZB
C208
1/10GZ0C
X201
S-SW
52
5V
13
53
R1012
1/10GJ
100C
Q831
AJ
<X-RAY>
54
R1011
1/10GJ
330KC
R813
1/10GJ
10KC
C811
EM1
LBWA
R810
10K
55
R205 1/10GZ0C
C209
KK0.047
LZB
R206
1/10GJ
22KC
56
C212
EM1
LBWA
C213
25EM4.7
LBWA
C129
R129
CJ330 CL 1/10GJ
220C
57
R867
1/10GJ
1MC
R353
10K
GND
8
VCC
R426
680
58
5V
C1007
25EM4.7
LBWA
D843
R
59
R1009
1/10GJ
100C
R2 IN
<ABL IN>
60
Video
<RESET>
61
5
62
C211 EM0.47
LBWA
R136
1/10GJ
1.5KC
C141
63FJ
0.047LBZA
R137
1/10GJ
47KC
63
SW1901
<H-PULSE>
L2 IN
C1006
25EM4.7
LBWA
<S-SW>
25KK0.1 R138
LZB 1/10GJ
47KC
R142
1/10GJ
33KC
C142
R143
1/10GJ
1KC
C147
KK0.01
LZB
64
S-VIDEO
R1008
1/10GJ
75C
C1004
EM2.2
LBWA
<X-RAY>
R128
1/10
GJ820KC
C214
EM2.2
LBWA
R209
1/10GJ
680KC
R208
1/10GJ
680C
R207
1/10GJ
22KC
L141
J
K1002
V2 IN
R144
1/10GZ
0C
R139
1/10GJ
470C
<IF>
X141
TP132
POWER
<V2 IN>
5VB6
S-GND
D1059
UDZS
10BG
<AV1/2>
Q132
AC
VOL.+
<V1 IN>
IC1001
NJM2533MP
L132
J
VOL.-
R1052
1/10GJ
75C
C1059
16EM10
LBWA
R1901
1/10GJ
10KC
K1051
1
<C IN>
TP16
B1
<130V>
CH +
D1052
DZXLB
ZA10B
R1059
470
S-SW
C IN
<Y IN>
D101
CH -
Y IN
R1051
1/10GJ
75C
<KEY IN>
C144
KK0.01
LZB
C103
KK0.01
LZB
D1901
L143
C143
16EM47
LBWA
R107
DJ10K
PRESET
SW1905
L142
J
C101
6.3EM
220LBWA
R857
100
R141
1/10GJ
680C
R856
100
R1911
1K
5VB6
SW1906
5VB6
SW1902
SW1903
C106
EM3.3
LBWA
SW1904
<RF AGC>
L1901
C1051
16EM22LBWA
C1052
KK0.01LZB
R1902
1/10GJ1KC
5V
15
R1903
1/10GJ1.8KC
R1904
1/10GJ2.2KC
AGC
MB
R1905
1/10GJ3.9KC
GND
10
IF
PB
TU+B
CLK
DATA
14 13 12
A1901
U20B40500
R1906
1/10GJ5.6KC
A101
TUNER
D1051
DZXLB
ZA10B
D1902
R1907
1/10GJ12KC
MODEL DS20930
32
C606
250KM
1000VBBW
:250KM
1000VBW
L901
DEG COIL

April / 2004 / 2000 SMC
Printed in U.S.A.
AS
Notice
CORRECTION
PRODUCTION CHANGE
SERVICE FLASH
ADD INFORMATION
FILE NO.
REVISION 04

Category :
COLOR TELEVISION
Model:
DS20930
Date:
JULY / 15 / 2003
Destination: U.S.A. / CANADA
20930-04
REF : No. SM780088-03
NOTE: Match the Chassis No. on the units back cover with the Chassis No. in the Service
Manual. If the Service Manual Chassis No. does not match the units, additional Service
Literature is required. This chassis is similar to Chassis No. 20930-03. Only the
difference Service Information is given in this manual. For detailed Service Information,
refer to the Original Service Manual and Notices for Chassis No. 20930-03 used in Model
DS20930 (SM780088-03).
1. IN THE CHASSIS ELECTRICAL PARTS LIST
The reason for change.

A : Misprint
B : Quality Reliability
D : Design
E : Add as a possible sub
G : Purchasing Request
C : Standardization
F : Schematic location change
Page &
Section
Schematic
Location
Page 19,
Chassis
Electrical
Parts List
R497
Old
401 068 1600
OXIDE-MT 4.7 JA 2W
1
NO
-------------------------------------------------------------New
401 068 6209
OXIDE-MT 5.6 JA 2W
1
NO
A100
Old
610 306 8077
ASSY, PWB, MAIN
1
NO
-------------------------------------------------------------New
610 306 8176
ASSY, PWB, MAIN
1
NO
A700
Old
610 306 8084
ASSY, PWB, SOCKET
1
YES
-------------------------------------------------------------New
610 306 8183
ASSY, PWB, SOCKET
1
YES
Q901
Old
414 012 3209
CRT A51QDX992X003
1
NO
-------------------------------------------------------------New
414 012 3100
CRT A51QDK190X022
1
NO
Page 20
Chassis
Electrical
Parts List
Part No.
DS20930, G8TBA, PRODUCT CODE 111367880
Description
Qty
Interchangeability
Reason

July / 2003 / 2000 SMC
Printed in U.S.A.
AS
Notice
CORRECTION
PRODUCTION CHANGE
SERVICE FLASH
ADD INFORMATION
FILE NO.
REVISION 03

Category :
COLOR TELEVISION
Model:
DS20930
Destination:
U.S.A. / CANADA
Date:
JULY / 15 / 2003

REF : No.
20930-03
SM780078
NOTE: Match the Chassis No. on the units back cover with the Chassis No. in the Service Manual.
If the Service Manual Chassis No. does not match the units, additional Service Literature
is required. This chassis is similar to Chassis No. 20930-00, however, all Service Information
is given in this Notice for Chassis No. 20930-03 used in Model DS20930.
Contents
Specifications
Safety Instructions . . . . . . . . . . . . . . . . . . 2
Service Adjustments . . . . . . . . . . . . . . 3 - 9
Purity and Convergence . . . . . . . . . 10 - 11
Service Hints . . . . . . . . . . . . . . . . . . . . . . 12
Mechanical Disassemblies. . . . . . . . . . . 13
Chassis Electrical Parts List . . . . . . 14 - 20
Cabinet Parts List . . . . . . . . . . . . . . . . . . 21
Component and Test Point
Locations . . . . . . . . . . . . . . . . . . . 22 - 24
Schematic Insert . . . . . . . . . . . . . . . 25 - 32
Schematic Notes . . . . . . . . . . . . . . . . . 25
Pin Layouts . . . . . . . . . . . . . . . . . . . . . 25
Capacitor and Resistor Codes . . . . . . 25
Block Diagram . . . . . . . . . . . . . . . 26 - 27
Voltage Charts . . . . . . . . . . . . . . . 26 - 28
Waveforms. . . . . . . . . . . . . . . . . . . . . . 28
Schematic Diagrams . . . . . . . . . . 29 - 32
Power Rating . . . . . . . . . . . . . . . . . . . . . 120V, 60Hz

75W (Avg), 2.0A (Max)
Antenna Input Impedance . . . . . . . . . . . . . . . . . 75
UHF/VHF/CATV
Receiving Channel . . . . . . . . . . . . . . . . 2 - 13 (VHF),
14 - 69 (UHF),
01, 14-94, 95-125 (CATV)
Remote Ready . . . . . . . . . . 24 Key Remote Control
Sound Output . . . . . . . . . . . . . . . . . . . . . . 1.0 W/CH
Intermediate Frequency
Picture IF Carrier . . . . . . . . . . . . . . . . . . 45.75MHz
Sound IF Carrier . . . . . . . . . . . . . . . . . . 41.25MHz
Color Sub Carrier . . . . . . . . . . . . . . . . . 42.17MHz
Picture Tube . . . . . . . . . . . . . . . . . A51QDX992X003
Semiconductors
Integrated Circuits. . . . . . . . . . . . . . . . . . . . . . . . 9
Transistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Except within Tuner and RC Pre-Amp.
Cabinet Dimensions
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 588mm
Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . 466mm
Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 493mm
DS20930, G8TAA, PRODUCT CODE 111367880
SAFETY INSTRUCTIONS
SAFETY PRECAUTIONS
WARNING: The chassis of this receiver has a floating
ground with the potential of one half the AC line voltage in
respect to earth ground. Service should not be attempted by
anyone not familiar with the precautions necessary when
working on this type of equipment.
The following precautions must be observed:
1. An isolation transformer must be connected in the power
line between the receiver and the AC line before any service is performed on the receiver.
READING SHOULD NOT EXCEED 750 mV.

AC VOLTMETER
(5000 ohms per volt or more sensitivity)
TELEVISION
RECEIVER
2. Comply with all caution and safety-related notes provided on the side of the cabinet, inside the cabinet, on the
chassis, and the picture tube.
1500 ohm
10 watt
3. When replacing a chassis in the cabinet, always be certain

that all the protective devices are installed properly, such
as control knobs, adjustment covers, shields and barriers.
DO NOT OPERATE THIS TELEVISION RECEIVER
WITHOUT THE PROTECTIVE SHIELD IN POSITION AND
PROPERLY SECURED.
4. Before replacing the back cover of the set, thoroughly
inspect the inside of the cabinet to see that no stray parts
or tools have been left inside.
Before returning any television to the customer, the
service technician must perform the following safety
checks to be sure that the unit is completely safe to
operate without danger of electrical shock.
ANTENNA COLD CHECK

Remove AC plug from the 120 VAC outlet and place a
jumper across the two blades. Connect one lead of an ohmmeter to the jumpered AC plug, and touch the other lead to
each exposed antenna terminal (UHF and VHF antenna terminals). The resistance must measure between 1M ohm and
5.2M ohm. Any resistance value below or above this range
indicates an abnormality which requires corrective action.
LEAKAGE CURRENT CHECK

Plug the AC line cord directly into a 120 VAC outlet. (Do not
use an isolation transformer for this check.) Use an AC voltmeter, that has 5000 ohms per volt or more sensitivity.
Connect a 1500 ohm 10 watt resistor, paralleled by a 0.15 F
150 VAC capacitor, between a known good earth ground
(water pipe, conduit, etc.) and all exposed metal parts of the
cabinet (antennas, handle bracket, metal cabinet, screw
heads, metal overlays, control shafts, etc.). Measure the AC
voltage across the 1500 ohm resistor. The AC voltage
should not exceed 750 mV. A reading exceeding 750 mV
indicates that a dangerous potential exists. The fault must
be located and corrected. Repeat the above test with the
receiver power plug reversed.
NEVER RETURN A RECEIVER TO THE CUSTOMER
WITHOUT TAKING THE NECESSARY CORRECTIVE ACTION.
Good earth ground

such as a water pipe,
conduit, etc.
0.15 F 150V AC
AC OUTLET
To be touched to all of exposed metal parts.

Voltmeter Hook-up for Leakage Current Check.
X-RADIATION PRECAUTION
The primary source of X-RADIATION in solid-state receivers is
the picture tube. The picture tube is specially constructed to
limit X-Ray emission. For continued X-RADIATION protection,
the replacement tube must be the same type as the original
(including the suffix letter in the part numbers). Excessive high
voltage may produce potentially hazardous X-RADIATION. To
avoid such hazards, the high voltage must be maintained within
specific limits. Refer to the X-RADIATION WARNING NOTE on
the CHASSIS SCHEMATIC in this service manual for specific
high voltage limits. If the high voltage exceeds specified limits,
check the components specified on the chassis schematic
diagram and take the necessary corrective action. Carefully
follow the instructions for the +B Voltage Check and the High
Voltage Check to maintain the high voltage within the specified
limits.

To prevent X-RADIATION from the picture tube due to
excessive high voltage, a HOLD-DOWN circuit is provided in
the high voltage circuit. Every time the receiver is serviced,
the high voltage HOLD-DOWN circuit must be tested for
proper operation. Refer to the HIGH VOLTAGE HOLDDOWN TEST in service adjustments.

When replacing components in a receiver, always keep in
mind the necessary product safety precautions. Pay special
attention to the replacement of components marked with a
star () in the parts list and in the schematic diagrams. To
ensure safe product operation, it is necessary to replace
those components with the exact same PARTS.
SERVICE ADJUSTMENTS
GENERAL
This set has an On-screen Service Menu system included in the CPU that allows remote operation for most of the service adjustments.
To enter the Service Menu, first disconnect the AC power cord. Then while pressing the MENU key on the front control panel, reconnect the AC power cord. The adjustments can now be made with the remote control or front control panel keys.
ON-SCREEN SERVICE MENU SYSTEM

1. Enter the Service Menu:
While pressing the MENU key on the front control panel, reconnect the AC power cord. The Service Menu Display will now
appear. (See Figure 1.)
NO.
DATA
XX OPT XXX XXXXXXXX
TITLE
ITEM NO.
BINARY DATA
(8 bit)
DECIMAL DATA
Figure 1. Service Menu Display

2. Service Adjustments:
Press the or key to select the desired service menu you want to adjust. (See page 4 for On-screen Service Menu.)
Use the + or key to adjust the data.

3. Exit from the Service Menu:
IC802 (EEPROM) REPLACEMENT

When IC802 (EEPROM) is replaced, IC801 (CPU) will automatically write the initial reference data into IC802 for basic TV operation.
However, the bus data should be checked and some bus data should be set up before attempting the service adjustments.
(See pages 4 6 for detailed information.)
INITIAL BUS DATA SETUP

Note: When IC802 (EEPROM) is replaced, change the following initial reference data for proper TV operation before
attempting the service adjustments.
1. Disconnect the AC power cord (AC 120V line).
2. While pressing the MENU key on the front control panel, reconnect the AC power cord.
The Service Menu display will now appear.
3. Select NO. 03 HP (H Phase) with or key. Adjust the data with + or key for 14.
4. Select NO. 04 VS (V Size) with or key. Adjust the data with + or key for 33.
5. Select NO. 07 VLN (V Lin) with or key. Adjust the data with + or key for 13.
6. Select NO. 10 VSC (V S Correction) with or key. Adjust the data with + or key for 6.
7. Select NO. 11 HBL (H Blanking Right) with or key. Adjust the data with + or key for 1.
8. Select NO. 12 HBL (H Blanking Left) with or key. Adjust the data with + or key for 5.
9. Select NO. 19 GD (Green Drive) with or key. Adjust the data with + or key for 6.
10. Select NO. 28 PRE (Preshoot Adj) with or key. Adjust the data with + or key for 3.
11. Select NO. 33 BSS (Black Streak Start) with or key. Adjust the data with + or key for 0.
12. Select NO. 37 AF (Auto Flesh) with or key. Adjust the data with + or key for 1.
13. Select NO. 54 SCO (Sub Color) with or key. Adjust the data with + or key for 14.
14. Select NO. 55 STI (Sub Tint) with or key. Adjust the data with + or key for 24.
15. Select NO. 57 OPT (SA Option ) with or key. Adjust the data with + or key for 100.
16. Select NO. 58 OP2 (SA Option 2) with or key. Adjust the data with + or key for 32.
17. Select NO. 63 SBO (Sub Bright Offset) with or key. Adjust the data with + or key for 4.
18. Press the MENU key to turn off the Service Menu display.
Table 1. ON-SCREEN SERVICE MENU

checked and be set up or readjusted according to the procedures described in the following pages. Initial Setup Data marked
with an * should be changed from Initial Reference Data. (See page 3 for Initial Bus Data Setup.)
NO.
TITLE
INITIAL REFERENCE
DATA
INITIAL SETUP
DATA
RANGE OF DATA
01
HFR
29
29
0~63
02
AFC
0, 1
AFC Gain & Gate
03
HP
15
14*
0~31
Horizontal Phase (Horizontal Centering)
04
VS
64
33*
0~127
Vertical Size
05
VPO
0~63
Vertical Position
06
VSP
0, 1
Vertical Set Up (Sync Sensitivity)
07
VLN
18
13*
0~31
Vertical Linearity
08
CRS
0~3
Cross B/W
09
GRY
0, 1
Gray Mode
10
VSC
6*
0~31
Vertical S Correction
11
HBR
1*
0~7
H BLK R
12
HBL
5*
0~7
H BLK L
13
CDM
0, 1
C D Mode
14
VC
0~7
Vertical Compression
FUNCTION
Horizontal Frequency
15
RB
0~255
Red Bias
16
GB
0~255
Green Bias
17
BB
0~255
Blue Bias
18
RD
64
64
0~127
Red Drive
19
GD
6*
0~15
Green Drive
20
BD
64
64
0~127
Blue Drive
21
SBI
48
48
0~127
22
OSD
0~3
23
POS
0, 1
Pre/Over SW
24
FLS
0~7
Filter System
25
CKO
0~7
Color Killer Operation
26
GYA
0, 1
G-Y Angle
27
CRG
0~3
Coring Gain
28
PRE
3*
0~3
Pre Shoot Adjust
Sub Bias
OSD Contrast
29
WP
0, 1
White Peak Limiter
30
FSW
0, 1
FBP Blanking Switch
31
VBL
0, 1
Vertical Blanking Switch
32
BSG
0~3
Black Str Gain
33
BSS
0*
0~3
Black Str Start
34
DCR
0~3
DC Reset
35
YGM
0~3
Y Gamma
36
CBP
0, 1
C Bypass
37
AF
1*
0, 1
Auto Flesh
38
BAT
0~7
Bright ABL Threshold
39
MSD
0, 1
Mid Stop Def
40
ABL
0, 1
Auto Bright Limit
41
RYA
0~15
R-Y/B-Y Angle
42
RAD
15
15
0~63
RF AGC Delay
43
IAS
0, 1
IF AGC
44
FMM
0, 1
FM Mute
45
FL
15
15
0~31
FM Level
Table 1. ON-SCREEN SERVICE MENU (Continued)

checked and be set up or readjusted according to the procedures described in the following pages. Initial Setup Data
marked with an * should be changed from Initial Reference Data. (See page 3 for Initial Bus Data Setup.)
NO.
TITLE
INITIAL REFERENCE
DATA
INITIAL SETUP
DATA
RANGE OF DATA
FUNCTION
46
VL
0~7
Video Level
47
EWD
39
39
0~63
EW DC
48
EWA
30
30
0~63
EW Amp
49
EWT
34
34
0~63
EW Tilt
50
EWP
0~7
EW Corner Top
51
EWB
0~7
EW Corner Bottom
52
HSC
0~7
Horiz Size Comp
53
SB
32
32
0~63
Sub Bright
54
SCO
14*
0~31
Sub Color
55
STI
20
24*
0~31
Sub Tint
56
SSH
12
12
0~31
Sub Sharpness
57
OPT
100*
0~255
Option (See Note 1 page 6.)
58
OP2
32*
0~255
Option 2 (See Note 2 page 6.)
59
HR
27
27
0~63
OSD Horizontal Position
60
ATT
0~63
Input Level
61
WDB
32
32
0~63
Wideband
62
SPC
32
32
0~63
Spectral
63
SBO
4*
0~255
Sub Bright Offset
64
PCO
40
40
0~63
PIP Color
65
PTI
40
40
0~63
PIP Tint
66
PUV
24
24
0~63
PIP Top Position
67
PDV
147
147
0~255
PIP Bottom Position
68
PLH
10
10
0~63
PIP Left Position
69
PRH
101
101
0~255
PIP Right Position
70
PCN
42
42
0~63
PIP Y Level
71
PBS
15
15
0~63
PIP BGP Phase
72
DRV
64
64
0~127
Red Drive Adjustment
(See Note 3 page 6.)
64
64
0~127
Blue Drive Adjustment
0~255
Red Bias Adjustment
0~255
Green Bias Adjustment
0~255
Blue Bias Adjustment
73

PROGRAM CODES
DRIVE / BIAS ADJUSTMENTS
The microprossesor used in this model is a multi-purpose

type and is used in several different models. To ensure
proper operation and the correct features for your particular model, the Program Codes must be correct.
Note 3. Red/Blue Drive Adjustments in Service Menu NO.

72 DRV: Adjust Red and Blue Drive Levels alternately with
1, 3, 7, and 9 keys on the remote control. (See Figure 2.) The
Drive Level adjustment data will be written in the Service
Menu No. 18 and 20 automatically.
Note 1. Option Data 1 (NO. 57 OPT) should be decimal 100

(01100100 binary). See page 3 INITIAL DATA SETUP, step
12, for set up procedure. If this program code is wrong the
TV will not operate properly.
BIT
FUNCTION
1
RD()
DATA
0
0, 1
TV
HOTEL
MONITOR
00: TV
01: HOTEL
10: MONITOR
11: INHIBITED (=TV)
VIDEO INPUT
NONE
3, 4
CLOCK
NOT USED
STEREO/MONO
MONO
6, 7
SURROUND
(N/A)
(N/A)
BD()
(N/A)
BD(+)
STEREO
00: NONE
01: YES
10: NOT USED
11: NOT USED
Note 2. Option Data 2 (NO. 58 OP2) should be decimal 32

(00100000 binary). See page 3 INITIAL DATA SETUP, step
13, for set up procedure. If this program code is wrong the
TV will not operate properly.
YES
NONE
COLOR ENHANCER
NOT USED
INITIAL CHANNEL
NOT USED
NOT USED
NOT USED
PIP
AV1/AV1, AV2
TONE/BASS, TREBLE
GAME KEY
NOT USED
AV1
AV1, AV2
NOT USED
NONE
(N/A)
RB(+)
GB()
(N/A)
GB(+)
BB()
(N/A)
BB(+)
Figure 3.
DATA
VGUIDE
Note 4. Red/Green/Blue Bias Adjustments in Service Menu

NO. 73: Adjust each Bias Level with 1, 3, 4, 6, 7, or 9 key on
the remote control. (See Figure 3.) The Bias Level adjustment data will be written in the Service Menu No. 15 ~ 17
automatically.
YES
Figure 2.
FUNCTION
3
RD(+)
(N/A)
RB()
BIT
2
(N/A)
YES

ANTENNA CONNECTIONS
VCO ADJUSTMENT
This receiver is designed for UHF/VHF reception. A 75 ohm

terminal is provided for UHF and VHF receptions. When
connecting a CATV antenna system, connect the 75 ohm
coaxial cable directly to the 75 ohm terminal. For 300 ohm
VHF antenna, use an adapter (not included with the TV set).
Note: VCO must be adjusted after IC101 (Signal Processor),

IC802 (EEPROM) or T151 (VCO Coil) is replaced.
CIRCUIT PROTECTION
Fuse F601 (4A) is included in the AC line. This fuse must be
replaced with the proper fuse (see Parts List).
CAUTION
4A 125V

ATTENTION : POUR MAINTENIR LA PROTECTION CONTRE LES RISQUES
D INCENDIE UTILISER UN FUSIBLE DE
+B VOLTAGE CHECK
Connect Voltmeter + lead to TJ1 130V and lead to ground
(TE7). Connect receiver to AC 120V line. Tune receiver to an
active channel. Reset the picture controls to the FACTORY
PRESET levels (press remote control RESET key twice).
Voltage must measure between +128.0V and +132.0V. If the
voltage is out of this range, the power circuit must be
checked. No +B adjustment is provided on this chassis.
HORIZONTAL CENTERING ADJUSTMENT

2. Check that picture is in the horizontal center of TV screen.
If picture is not centered horizontally, perform steps 3 ~ 6.
5. Select NO. 03 HP (Horizontal Phase) with or key.
6. Adjust the data with + or key for horizontal center. To
turn off the Service Menu display, press the MENU key.

2. Set the picture controls to the Sports level.
3. Connect digital voltmeter + lead to pin 58 of IC101 and
lead to ground (TE 7).
4. Confirm a reading of 3.6 0.2 VDC.
5. If voltage is out of specifications adjust T151 for
3.6 0.2 VDC.
RF AGC ADJUSTMENT
1. Tune receiver to strongest VHF station in your area.
2. Set contrast and brightness controls for maximum.
(120V AC line).
5. Select NO. 42 RAD (RF AGC Delay) with or key.
6. Adjust the data with + or key in the direction which
causes snow to appear; then in the opposite direction
until the snow just disappears.
7 . To turn off the Service Menu display, press the MENU key.
VIDEO LEVEL
1. Connect color-bar generator to antenna terminals.
(AC 120V line).
3. Connect oscilloscope to TP16 (Q202 emitter) and ground.
5. Select NO. 46 VL (Video Level) with the or key.
6. Adjust the + or key for an oscilloscope reading of 1.0
0.1 VP-P at TP16. Press the MENU key to turn off the
Service Menu display.
VERTICAL SIZE ADJUSTMENT

2. Check the vertical size of the picture. If the vertical size is
too large or small, perform steps 3 ~ 6.
5. Select NO. 04 VS (Vertical Size) with or key.
6. Adjust the data with + or key for full scan. To turn off
the Service Menu display, press the MENU key.
VERTICAL CENTERING ADJUSTMENT

2. Check that picture is in the center of TV screen. If picture
center is too low, add resistor R513 (1K ohm 1/2W). If picture
center is too high, add resistor R512 (1K ohm, 1/2W).
1.0 0.1 VP-P
Figure 4.

BRIGHTNESS LEVEL ADJUSTMENT
GRAYSCALE ADJUSTMENT
1. Set the picture controls to the Sports levels or Reset
(use MENU key and or key or RESET key).
(120V AC line).
4. Select NO. 15 RB (Red Bias), NO. 16 GB (Green Bias),
and NO. 17 BB (Blue Bias) with or key and set each
data to 0 with + or key.
5. Select NO. 18 RD (Red Drive) and NO. 20 BD (Blue Drive)
with or key and set each data to 64 with + or key.
6. Set NO. 19 GD (Green Drive Reduction) data to 6, NO. 53
SB (Sub-Brightness) data to 32, NO. 54 SCO (Sub Color)
data to 14, NO. 55 STI (Sub Tint) to 24, and NO. 56 SSH
(Sub Sharpness) data to 12 with or , and + or keys.
7. Turn Screen Control (T402) to minimum (fully counterclockwise).
8. Select the Service Menu NO. 73 (Bias Adjustments) with
or key.
9. Advance Screen Control (T402) clockwise to obtain just
visible one color line. If line does not appear, place this
control to maximum (fully clockwise).
10. Raise each Bias Level with 3, 6, and 9 keys to obtain just
visible white line. See Figure 5.
1
RB()
(N/A)
RB(+)
GB()
(N/A)
GB(+)
BB()
(N/A)
BB(+)


Service Menu NO. 73
11. Select the Service Menu NO. 72 DRV (Drive Adjustments)
with or key.
12. Adjust Red and Blue Drive Levels alternately with 1, 3,
7, or 9 key to produce normal black and white picture in
highlight areas. (See Figure 6.)
1
RD()
(N/A)
RD(+)
(N/A)
(N/A)
(N/A)
BD()
(N/A)
BD(+)
Note: Grayscale, RF AGC, Video Level, and High Voltage Check

must be adjusted before attempting Brightness Level
Adjustment.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Connect a color-bar generator to the antenna terminals.

Switch the generator to the crosshatch pattern.
Reset the picture controls to the Sports levels.
Connect voltmeter (high impedance) + lead to terminal
TP51 and lead to terminal TP50 on main board. Set
voltmeter for 1.5V ~ 3V range.
Turn off the receiver and disconnect the AC power cord.
While pressing the MENU key, reconnect the AC power
Select NO. 53 SB (Sub Brightness) with or key.
Adjust the data with + or key for 680mVDC.
Check brightness level on every active channel, readjust
(repeat steps 5 ~ 9), if necessary.
Note: Do not set to excessive brightness level, otherwise

the contrast level will be suppressed.

Every time the receiver is serviced, the HIGH VOLTAGE
HOLD-DOWN circuit must be tested for proper operation by
following these steps:
1. Connect receiver to 120V AC line. Tune receiver to
active channel. Reset the picture controls to the Sports
levels.
2. Check that the voltage measured between TP7 and TE7
(ground side) is within 16.5 VDC to 21 VDC. If the voltage is out of this range, the Hold-Down Circuit must be
checked.
3. Connect a DC Voltage supply to TP7 and TE7 through a
100 ohm 1/4W resistor. Adjust the DC voltage to 23 VDC.
The receiver should shutdown, losing raster and sound.
Then the receiver should turn off automatically. This
reaction indicates that the Hold-Down circuit is functioning properly. If the receiver does not shutdown, a
malfunction is indicated and its cause must be found
and corrected.
4. To obtain picture again, remove the DC Supply and wait
a few minutes. Now turn on the receiver.
HIGH VOLTAGE CHECK

Note: +B (+130V) Voltage Check and Grayscale Adjustment
must be completed before attempting high voltage
Check.

Service Menu NO. 72 DRV
13. Check for proper grayscale at all brightness levels.
To turn off the Service Menu display, press the MENU key.
Note: If Grayscale Adjustment is made after picture tube
replacement, check Brightness Level Adjustment.
FOCUS ADJUSTMENT
Adjust focus control (T402) for well defined scanning lines.
1. Connect high voltage voltmeter lead to ground, and

connect + lead to anode of picture tube.
2. Tune receiver to an active channel and confirm TV is
operating properly.
3. Eliminate the beam current by adjusting the contrast
and brightness controls to minimum.
4. Confirm high voltage is within 28.0 KV and 31.1 KV. If
reading is not within range, check horizontal circuit.
No high voltage adjustment is provided on this chassis.
SOUND ADJUSTMENT
SEPARATION ADJUSTMENT
1. Connect a color-bar generator to the antenna terminals

with audio signal of 1KHz at 100% modulation.
2. Set the picture controls to the Sports levels
3. Connect oscilloscope + lead to TP21 (base Q135) and
lead to ground.
(AC 120V line).
6. Select NO. 45 FL (FM Level) with the or key.
7. Adjust the data with the + or key for an oscilloscope
reading of 0.693 10% VP-P at TP21.
8. Press the MENU key to turn off the Service Menu display
and disconnect the oscilloscope from the chassis.

(AC 120V line).
8. Connect oscilloscope CH1 to TP317 and CH2 to TP318
and ground.
9. Connect an MTS TV/Stereo generator to antenna terminal.
11. Select pilot, 300Hz audio frequency and Left modulating
signal.
12. Select NO. 61 WDB (Wide Band) with the or key.
13. Adjust the + or key for minimum low frequencies at
14. Select 4 KHz audio frequency and Right modulating signal.
15. Select NO. 62 SPC (Spectral) with the or key.
16. Adjust the + or key for minimum high frequencies at
Repeat adjustments (steps 1116) until no further decreases
in amplitude can be obtained. Press the MENU key to turn
off the Service Menu display.
0.693 10% VP-P
Minimize L leakage
Figure 7.
TP317 (R)
MULTI-SOUND SECTION ADJUSTMENTS
300Hz
Note: Multi-Sound Section must be adjusted after

IC101 (Signal Processor), IC3401 (MTS Decoder), or
IC802 (EEPROM) is replaced.
Minimize R leakage
TP318 (L)
4KHz
INPUT LEVEL ADJUSTMENT

1. Connect a signal to the antenna terminals with audio of
1 KHZ 100% modulation.
(AC 120V line).
3. Connect voltmeter (RMS) to TP317 and ground.
5. Select NO. 60 ATT (Attenuation) with the or key.
6. Adjust the + or key for a voltmeter reading of 400 20
mVrms at TP317.
Figure 8. Separation Adjustments
PURITY AND CONVERGENCE ADJUSTMENTS

CAUTION: The Purity and Convergence adjustments have been made at the factory. Readjustments should be made
only after the picture tube or deflection yoke is replaced. Follow the steps below for necessary readjustments.
PURITY ADJUSTMENTS
DEFLECTION YOKE
RUBBER
WEDGE
DEFLECTION YOKE
MOUNTING SCREW
Figure 1. Deflection Yoke Movement
PURITY
MAGNET
TABS
SIX-POLE
MAGNET TABS
FOUR-POLE
MAGNET TABS
34
12
1. When replacing picture tube or deflection yoke, mount

deflection yoke and purity and convergence magnets
assembly properly. See Figure 1. Position the picture
tube facing east or west. Demagnetize the picture tube
and receiver using an external degaussing coil. Set
receiver to Service Menu NO. 73 (no vertical sweep)
while degaussing.
2. Place the yoke on tube neck fully forward against glass.
3. Place the CPM on the tube neck aligning the center of
the purity magnet tabs over center of Focus Gap (G3 & G4).
See Figure 2.
4. Connect a color-bar generator to the antenna terminal.
Switch the generator to a white field. Move yoke backward on the neck until a uniform white field is obtained.
5. Allow 30 minutes warm up on a blank white field (high
intensity grayscale).
Note: If white field cannot be obtained check Grayscale
Adjustments on page 8.
6. Reset the picture controls to the Auto levels. Select a green
raster, either with the signal generator or by adjusting the
bias controls. If a signal generator is used for this step skip
to Step 11. If the bias controls will be used go to step 7.
7. Adjust Service Menu NO. 15 RB (Red Bias), NO. 16 GB
(Green Bias), and NO. 17 BB (Blue Bias) data each to 00.
8. Select Service Menu NO. 73 (no vertical sweep).
9. Adjust the Screen Control counterclockwise until the
horizontal scan line is no longer visible.
10. Select Service Menu NO. 16 GB (Green Bias) and
increase the data to produce a green raster. If retrace
lines appear reduce screen control slightly.
11. Pull yoke back on tube neck to obtain three-color raster
(blue, green and red).
12. Adjust the angle between the two purity magnet tabs to
center the vertical green belt in the picture tube. Do not
rotate tabs. See Figure 3.
13. Slowly slide the deflection yoke forward until a uniform
green screen is obtained.
14. Check the purity of the red and blue screens for uniformity. Turn off other colors to check (use bias controls or
use generator). If necessary, readjust the yoke position
until all screens are pure.
15. If bias controls and screen control were used to set purity reset Grayscale and Bright Level. Refer to Grayscale
Adjustment on page 8 and Brightness Level Adustment
on page 8.
16. Confirm that the yoke is not tilted. Tighten the yoke
mounting screw. Adjust convergence next.
ANGLE
OF TABS
FOCUS GAP
(G3-G4)
Figure 2. Purity and Convergence Magnets
ANGLE OF MAGNET TABS
MAGNET TABS
Figure 3. Adjusting Magnet
10
CONVERGENCE ADJUSTMENT
CENTER CONVERGENCE ADJUSTMENT
OUTER AREA CONVERGENCE ADJUSTMENT
1. Connect a crosshatch generator to antenna terminals.

2. Set Contrast to low level to eliminate blooming. Reduce
Brightness level to obtain black background if necessary.
3. Adjust the angle between the four-pole magnet tabs 1
and 2 (Figure 2), and superimpose the red and blue vertical lines in the center area of the picture screen. See
Figure 4.
4. Keeping the tabs at the same angle, rotate them together
to superimpose the blue and red horizontal lines in the
center area of the picture screen. See Figure 4.
5. Adjust the six-pole magnet tabs 3 and 4 so the converged red/blue line is superimposed on the green line.
This is the same procedure used in steps 3 and 4. See
Figure 5.
The outer area convergence is performed by positioning of

the yoke as follows:
1. Move the top of the yoke toward or away from the picture tube. This movement will affect the vertical lines at
the top and bottom and the horizontal lines at the sides.
See Figure 6.
2. Check that splits at 12 oclock and 6 oclock positions
are minimized, adjust yoke for best compromise.
Secure with wedge at 12 oclock position. See Figure 1.
3. Move the side of the yoke toward or away from the picture tube to converge the horizontal lines at the top and
bottom and the vertical lines at the sides. See Figure 7.
4. Check that splits at 12 oclock and 6 o,clock are minimized, adjust yoke for best compromise. Secure yoke
position with the side wedges. See Figure 1.
Note: When re-using the rubber wedges, apply a small
amount of silicone rubber adhesive or hot melt to
each of the wedges.
BLUE
GREEN
BLUE
RED
BLUE
RED
GREEN
Adjust four-pole tabs angle to
superimpose blue and red vertical
line.
Adjust four-pole tabs together

to superimpose red and blue
horizontal line.
RED
Figure 4. Blue and Red Line Movement

Line movement when adjusting
top of yoke in and out.
Figure 6. Top of Yoke Movement
BLUE
GREEN
RED
BLUE / RED
BLUE
GREEN
RED
BLUE
GREEN
RED
GREEN
Adjust six-pole tabs angle to

superimpose red / blue and
green vertical line.
Adjust six-pole tabs together

to superimpose red / blue and
green horizontal line.
BLUE
GREEN
RED
Figure 5. Blue/Red and Green Line Movement
Line movement when adjusting

side of yoke in and out.
Figure 7. Side of Yoke Movement
11
SERVICE HINTS
POWER FAILURE DETECTOR
This unit is equipped with a Power Failure Detector function included in the CPU which checks for an abnormal condition in
the chassis power supplies, including the power supply derived from the Horizontal Output Transformer.
If, while the power is on, a failure is caused by any of the following that results in a low voltage supply, the CPU will turn the
unit off in 1.5 seconds to prevent further damage:
Failure within the power supply circuits.

A short circuit in the load side from the supply.
Stoppage of the Horizontal Output Oscillator caused by the X Radiation protection Hold-Down Circuit.
If, while the power is off, the power is switched on and any of these failures remains uncorrected, the CPU will shut off the
power within three seconds.
Check the following if the unit is turned off by the power failure detector.
1. Disconnect the AC power cord (120V AC line) for at least 10 seconds.
2. Connect a DC Voltmeter to the following TEST POINTS.
TJ6
D429 Cathode
5V
5V
3. Press the Power key and check for the proper voltage supplies.
4. If either of these voltages is low, the power failure detector should turn the unit off within three seconds.
5. Check all circuits listed above.
Note: This unit is equipped with a Power Surge Protection feature included in the CPU. If power failure occurs three times
within 15 minutes, the CPU will automatically stop functioning to help prevent secondary damage. (TV will not turn on
by pressing the power key.) To reset the operating programs within the CPU, disconnect the AC power cord for at least
10 seconds.
12
MECHANICAL DISASSEMBLIES
CABINET BACK REMOVAL
CHASSIS REMOVAL
1. Refer to Figure 1, remove 8 screws.

2. Pull off cabinet back and remove.
1. Remove cabinet back.

2. Discharge the picture tube anode (2nd anode lead) to the
dag coating (picture tube grounding lead).
3. Disconnect degaussing coil socket (KD), picture tube
socket, deflection yoke connector (KX), speaker
connector (KSP), picture tube ground leads, and 2nd
anode lead.
4. Remove chassis completely by sliding it straight back.
PICTURE TUBE REMOVAL

CAUTION: Do not disturb the deflection yoke or magnet
assembly on the picture tube neck. Care must be taken to
keep these assemblies intact, unless picture tube is being
replaced. Discharge the picture tube to the coating before
handling the tube.
AV2 INPUT
1. Remove chassis, see Chassis Removal instructions.

2. Place cabinets front face down on a soft surface.
3. Remove the screw on each corner of the picture tube and
GENTLY lift the picture tube out of the cabinet.
4. Install a replacement picture tube in reverse order.
Properly install the degaussing coil and picture tube
grounding lead on the picture tube. See Figure 2.
AUDIO
L
S-VIDEO
(MONO)
UHF / VHF / CATV

75
VIDEO
Figure 1. Cabinet Back Removal
Note: If Picture Tube is being replaced, mount the Degaussing

Coil properly on the tube. See Figure 2.
DEGAUSSING
COIL
DEGAUSSING
COIL HOLDER
DEGAUSSING
COIL HOLDER
TO PICTURE TUBE
SOCKET BOARD
GROUND
DEGAUSSING
COIL SOCKET
PICTURE-TUBE
GROUNDING LEAD
Figure 2. Picture Tube Removal
13
CHASSIS ELECTRICAL PARTS LIST

CAUTION: To Protect against electrical shock and for continued product safety, refer to SAFETY PRECAUTIONS,
X-RADIATION PRECAUTIONS, HIGH VOLTAGE HOLD-DOWN TEST, and PRODUCT SAFETY NOTICE on Page 2.

PRODUCT SAFETY SHOULD BE CONSIDERED WHEN A REPLACEMENT IS MADE IN ANY AREA OF A RECEIVER.
COMPONENTS INDICATED BY A STAR () IN THIS PARTS LIST AND THE SCHEMATIC DIAGRAM DESIGNATE
COMPONENTS IN WHICH SAFETY CAN BE OF SPECIAL SIGNIFICANCE. IT IS PARTICULARLY RECOMMENDED
THAT ONLY PARTS DESIGNATED ON THE FOLLOWING PARTS LIST BE USED FOR COMPONENT REPLACEMENT
DESIGNATED BY A STAR. NO DEVIATIONS FROM RESISTANCE, WATTAGE, AND VOLTAGE RATINGS MAY BE MADE
FOR REPLACEMENT ITEMS DESIGNATED BY A STAR.
Notes: Parts having Location Number are located on the following boards.
Numbers under 700 Series . . . . . . . . . . . . . . . . . . . . .On the Main Board.
Numbers 700 Series . . . . . . . . . . . . . . . . . . . . . . . . . . .On the Picture Tube Socket Board.
Numbers 900 Series . . . . . . . . . . . . . . . . . . . . . . . . . . .Out of Board.
All Other Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . .On the Main Board
Note: Schematic part location numbers may not always match with the part descriptions.
The part descriptions are correct and should be used.
Schematic
Location
Part No.
Schematic
Location
Description
CAPACITORS
NOTES:
Read description of the Capacitor as follows:
(Example)
CERAMIC
100P
50V
Rated Voltage
Tolerance Symbols:
less than 10PF
A . .Not specified
B . .0.1PF
C . .0.25PF
D . .0.5PF
F . .1PF
G . .2PF
R . .+0.25 - 0PF
S . .+0 - 0.25PF E . .+0 - 1PF
more than 10PF
A . .Not specified
B . .0.1%
C . .0.25%
D . .0.5%
F . .1%
G . .2%
H . .3%
J . .5%
K . .10%
L . .15%
M . .20%
N . .30%
P . .+100 - 0%
Q . .+30 - 10% T . .+50 - 10%
U . .+75 - 10% V . .+20 - 10%
W .+100 - 10% X . .+40 - 20%
Y . .+150 - 10% Z . .+80 - 20%
Rated Value: P...Pico Farad U...Micro Farad
Material:
CERAMIC . . . . . .Ceramic
MT-PAPER . . . . .Metalized Paper
POLYESTER . . .Polyester
MT-POLYEST . .Metalized Polyester
POLYPRO . . . . .Polypropylene
MT-POLYPRO . .Metalized Polypropylene
COMPO-FILM . .Composite Film
MT-COMPO . . . .Metalized Composite
STYRENE . . . . . .Styrene
TA-SOLID . . . . .Tantalum Solid
AL-SOLID . . . . . .Aluminum Solid
ELECT . . . . . . . .Electrolytic
NP-ELECT . . . . .Non-Polarized Electrolytic
OS-SOLID . . . . .Aluminum Solid with Organic
Semiconductive Electrolytic
14
C001
C002
C003
C004
C006
C010
C011
C012
C015
C101
C103
C106
C131
C133
C134
C136
C137
C141
C142
C143
C146
C147
C151
C153
C161
C211
C212
C221
C251
C252
C253
C256
C257
C258
C272
C274
C284
Part No.
404 087 2801

404 087 2801
403 235 5701
403 235 5701
403 224 6108
404 087 2306
404 087 2306
404 088 5702
404 084 3108
404 084 2408
403 224 6108
404 084 4006
404 084 3801
403 224 6108
403 224 5705
401 150 6001
403 364 7508
403 224 6108
403 343 4603
403 224 6108
403 224 6108
404 084 2200
404 084 3702
404 084 3702
403 357 9601
404 084 6901
404 084 4006
404 084 6901
401 150 6001
404 086 6602
404 084 3702
404 084 3801
403 224 6108
404 084 3207
404 084 4105
404 084 2705
404 084 3207
Description
ELECT
ELECT
CERAMIC
CERAMIC
CERAMIC
ELECT
ELECT
ELECT
ELECT
ELECT
CERAMIC
ELECT
ELECT
CERAMIC
CERAMIC
MT-GLAZE
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
ELECT
ELECT
ELECT
CERAMIC
NP-ELECT
ELECT
NP-ELECT
MT-GLAZE
POLYESTER
ELECT
ELECT
CERAMIC
ELECT
ELECT
ELECT
ELECT
0.22 M 50V
0.22 M 50V
5600P K 50V
5600P K 50V
0.01U K 50V
220U M 25V
220U M 25V
22U M 16V
330U M 16V
470U M 6.3V
0.01U K 50V
2.2U M 50V
1U M 50V
0.01U K 50V
1000P K 50V
0.000 ZA 1/10W
10P J 50V
0.01U K 50V
0.022U K 50V
0.01U K 50V
0.01U K 50V
100U M 6.3V
0.47U M 50V
0.47U M 50V
0.1U Z 50V
1U M 50V
2.2U M 50V
1U M 50V
0.000 ZA 1/10W
0.047U K 63V
0.47U M 50V
1U M 50V
0.01U K 50V
47U M 16V
3.3U M 50V
10U M 16V
47U M 16V
Schematic
Location
C285
C401
C402
C403
C405
C406
C407
C408
C411
C416
C421
C427
C441
C471
C473
C482
C484
C489
C493
C497
C502
C503
C504
C505
C506
C508
C509
C511
C516
C601
C603
C604
C606
C608
C609
C612
C613
C614
C622
C625
C626
C628
C629
C630
C631
Part No.
403 224 6108

404 084 3306
403 224 6108
404 086 6800
404 084 6901
403 075 7101
403 076 3102
404 085 4609
404 077 4402
403 343 7901
403 346 7126
403 372 6807
404 081 2609
404 091 6406
403 224 6108
403 224 6108
404 084 3306
404 084 5706
403 115 0802
404 084 4204
404 084 3009
404 056 5307
404 084 2200
403 053 2104
403 276 0208
404 085 4500
404 084 5706
403 062 5301
403 312 2401
403 235 0300
404 084 5706
403 059 7707
403 059 8308
404 084 2705
404 066 2204
404 071 2404
404 089 1703
403 075 7101
403 075 7101
404 088 2909
404 088 7102
403 222 1303
403 262 1806
403 271 9602
404 042 7506
404 049 4706
404 085 9000
404 090 9002
404 086 6800
404 084 5003
404 084 4501
403 262 2308
403 266 4902
404 084 2903
404 073 9005
404 091 9704
404 084 3009
404 084 3801
404 088 2909
404 088 7102
Schematic
Location
Description
CERAMIC
0.01U K
ELECT
470U M
CERAMIC
0.01U K
POLYESTER
6800P J
NP-ELECT
1U M
CERAMIC
1000P K
CERAMIC
3900P K
ELECT
47U M
MT-POLYPRO 7200U H
MT-POLYPRO 7200U H
MT-POLYPRO 0.27U J
MT-POLYPRO 0.27U J
MT-POLYPRO 0.27U M
ELECT
220U M
CERAMIC
0.01U K
CERAMIC
0.01U K
ELECT
470U M
MT-POLYEST
0.47UJ
ELECT
22U M
ELECT
4.7U M
ELECT
220U M
NP-ELECT
2.2U M
ELECT
100U M 6
ELECT
220U M
ELECT
2.2U K
ELECT
2200U M
MT-POLYEST
0.47UJ
POLYESTER 5600P K
POLYESTER 5600P K
CERAMIC
56P J
MT-POLYEST
0.47UJ
POLYESTER
0.22U J
POLYESTER
0.22U K
ELECT
10U M
MT-POLYEST 0.22U M
MT-POLYEST 0.22U M
MT-POLYEST 0.22U M
CERAMIC
1000P K
CERAMIC
1000P K
CERAMIC
1000P M
CERAMIC
1000P M
CERAMIC
1000P K
CERAMIC
1000P K
CERAMIC
1000P K
ELECT
330U M
ELECT
330U M
ELECT
330U M
POLYESTER
3300P J
POLYESTER
6800P J
POLYESTER
0.01UJ
ELECT
470U M
CERAMIC
1200P K
CERAMIC
1200P K
ELECT
1000U M
ELECT
220U M
ELECT
220U M
ELECT
220U M
ELECT
1U M
CERAMIC
1000P M
CERAMIC
1000P M
50V
16V
50V
63V
50V
500V
500V
35V
1.5KV
1.5K
250V
250V
200V
6.3V
50V
50V
16V
63V
100V
50V
16V
100V
.3V
35V
50V
25V
63V
50V
50V
50V
63V
50V
50V
16V
275V
250V
275V
500V
500V
250V
250V
1K
1K
1K
200V
200V
200V
63V
63V
63V
35V
1K
1K
16V
160V
160V
16V
50V
250V
250V
C632
C634
C683
C689
C693
C701
C711
C721
C742
C801
C806
C809
C810
C811
C822
C829
C835
C841
C842
C843
C853
C854
C856
C857
C858
C862
C1001
C1002
C1051
C1052
C1059
C1071
C1080
C1081
C1902
C3401
C3404
C3406
C3407
C3408
C3411
C3412
C3413
C3414
C3416
C3417
C3418
C3421
C3422
C3423
C3424
C3426
C3427
C3431
C3432
C3433
C3434
C3436
C3439
15
Part No.
404 088 2909

404 088 7102
404 084 3207
404 084 3009
403 357 9601
404 086 5100
403 235 5305
403 224 5705
403 224 5705
403 077 2807
403 224 6108
404 084 2408
403 235 0607
403 235 0607
404 084 3801
404 088 5702
404 084 3801
403 224 6108
403 357 9601
403 357 9601
403 357 9601
404 087 1200
403 235 0508
404 084 3801
403 235 1000
403 224 5705
403 224 6108
404 084 2705
404 084 2705
404 088 5702
403 224 6108
404 084 2705
403 224 6108
403 357 9601
404 084 2705
404 084 2705
404 087 1200
403 086 0108
403 325 2504
403 235 5701
404 084 3702
404 084 3702
404 084 3207
404 084 4204
404 084 2804
403 086 0108
404 084 4204
403 086 0108
403 224 5606
403 323 3602
403 342 9203
403 086 0108
403 299 1820
404 084 3801
403 224 6009
404 087 1200
403 224 6009
403 343 4603
403 086 0108
403 086 0108
Description
CERAMIC
CERAMIC
ELECT
ELECT
CERAMIC
POLYESTER
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
ELECT
CERAMIC
CERAMIC
ELECT
ELECT
ELECT
CERAMIC
CERAMIC
CERAMIC
CERAMIC
ELECT
CERAMIC
ELECT
CERAMIC
CERAMIC
CERAMIC
ELECT
ELECT
ELECT
CERAMIC
ELECT
CERAMIC
CERAMIC
ELECT
ELECT
ELECT
NP-ELECT
CERAMIC
CERAMIC
ELECT 0
ELECT 0
ELECT
ELECT
ELECT
NP-ELECT
ELECT
NP-ELECT
CERAMIC
CERAMIC
TA-SOLID
NP-ELECT
TA-SOLID
ELECT
CERAMIC
ELECT
CERAMIC
CERAMIC
NP-ELECT
NP-ELECT
1000P M 250V
1000P M 250V
47U M 16V
220U M 16V
0.1U Z 50V
0.1U J 63V
1200P K 50V
1000P K 50V
1000P K 50V
1000P Z
2K
0.01U K 50V
470U M 6.3V
100P J 50V
100P J 50V
1U M 50V
22U M 16V
1U M 50V
0.01U K 50V
0.1U Z 50V
0.1U Z 50V
0.1U Z 50V
0.1U M 50V
82P J 50V
1U M 50V
220P J 50V
1000P K 50V
0.01U K 50V
10U M 16V
10U M 16V
22U M 16V
0.01U K 50V
10U M 16V
0.01U K 50V
0.1U Z 50V
10U M 16V
10U M 16V
0.1U M 50V
4.7U M 25V
0.012U K 50V
5600P K 50V
.47U M 50V
.47U M 50V
47U M 16V
4.7U M 50V
100U M 16V
4.7U M 25V
4.7U M 50V
4.7U M 25V
2700P K 50V
0.047U K 50V
3.3U K 10V
4.7U M 25V
10U K 10V
1U M 50V
4700P K 50V
0.1U M 50V
4700P K 50V
0.022U K 50V
4.7U M 25V
4.7U M 25V
Schematic
Location
C3441
C3442
C3447
C3448
Part No.
404 084 4204

404 084 4204
404 084 4204
404 084 4204
Schematic
Location
Description
ELECT
ELECT
ELECT
ELECT
4.7U M
4.7U M
4.7U M
4.7U M
50V
50V
50V
50V
D624
D625
D627
D629
DIODES
D001
D101
D351
D408
D421
D422
D428
D429
D471
D472
D481
D482
D486
D487
D490
D501
D502
D601
D602
D603
D604
D612
D613
D614
D623
408 047 4706

408 047 6205
408 047 6502
407 222 4401
407 158 1307
407 158 1307
407 054 5904
407 099 7109
407 013 4306
407 013 7109
408 008 2406
407 006 4108
407 007 7603
407 005 7308
407 005 8602
407 088 6502
407 007 6606
407 124 5506
407 124 6404
407 011 4407
407 054 0008
407 099 6102
407 005 7308
407 005 8602
407 011 3004
407 088 6502
408 009 9404
408 047 7707
407 005 7308
407 005 8602
407 011 3004
407 088 6502
408 009 9404
407 118 2207
407 005 7605
407 013 3200
408 008 8606
407 005 7605
407 013 3200
408 008 8606
407 005 7605
407 013 3200
408 008 8606
407 005 7605
407 013 3200
408 008 8606
407 218 0707
407 231 2801
407 057 9800
407 063 9702
407 006 0100
407 007 6606
407 124 5506
407 124 6404

ZENER DIODE MTZJ15C (15V)
DIODE 1S2076A
DIODE 1S2473
DIODE 1N4148
DIODE ERB44-04
DIODE EU2
DIODE EM01Z
DIODE ERA15-02
DIODE MPG06D
DIODE ES1
DIODE RMPG06G
DIODE ERA18-04
DIODE TVR1G
DIODE EM01Z
DIODE ERA15-02
DIODE S5277B
DIODE MPG06D
DIODE 1N4002ID
DIODE EM01Z
DIODE ERA15-02
DIODE S5277B
DIODE MPG06D
DIODE 1N4002ID
DIODE EM2B
DIODE 1S1887A
DIODE GP15G
DIODE EM2B
DIODE 1S1887A
DIODE GP15G
DIODE EM2B
DIODE 1S1887A
DIODE GP15G
DIODE EM2B
DIODE 1S1887A
DIODE GP15G
PC TLP421(BL)
PHOTO COUPLE PC123YC2
DIODE ERA91-02
DIODE ES1
DIODE RMPG06G
DIODE ERA18-04
D680
D683
D693
D699
D801
D831
D834
D836
D843
D1001
D1002
D1051
D1052
D1059
D1901
D1902
Part No.
407 106 2806

407 129 7000
407 211 5808
407 013 4306
407 013 7109
408 008 2406
407 054 7007
407 099 7208
407 013 4306
407 013 7109
408 008 2406
407 013 4306
407 013 7109
408 008 2406
407 057 4201
407 099 5600
407 006 0100
407 013 4306
407 013 7109
408 008 2406
407 222 5903
408 047 4706
407 013 4306
407 013 7109
408 008 2406
407 013 4306
407 013 7109
408 008 2406
408 047 2306
408 047 2306
408 047 2306
408 047 2306
407 206 5608
408 047 8605
408 047 2306
Description
DIODE RU3YX
DIODE RU4AM LF-L1
DIODE FE201-6L43
DIODE 1S2076A
DIODE 1S2473
DIODE 1N4148
DIODE 1S2076A
DIODE 1S2473
DIODE 1N4148
DIODE 1S2076A
DIODE 1S2473
DIODE 1N4148
DIODE ERA91-02
DIODE 1S2076A
DIODE 1S2473
DIODE 1N4148
ZD UDZS-TE-173.6B (3.6V)
DIODE 1S2076A
DIODE 1S2473
DIODE 1N4148
DIODE 1S2076A
DIODE 1S2473
DIODE 1N4148
ZENER DIODE UDZS10B (10V)
INTEGRATED CIRCUITS
IC001
IC101
IC501
IC601
IC681
IC801
IC802
IC1081
IC3401
409 275 7903

409 491 4809
409 453 5905
409 172 8102
409 528 6202
410 418 8602
409 333 3700
409 376 1503
409 440 8902
409 495 6908
409 497 0706
409 528 8404
409 051 3006
409 467 1108
IC LA4525
IC LA76834NM-TBM
IC LA78041
IC SE130NH
IC PQ050ES1MXP
IC M37272M*-***FP T4
IC 24LC02B/P
IC ST24C02B6
IC M24C02-BN6
IC CAT24WC02P
IC S524C20D21-DCB0
IC S524A40X21-DCB0
IC TC4053BP
IC CXA2134Q-T6
COILS
LF601
L164
L602
16
645 012 0589

645 052 6862
645 003 9713
645 016 2657
645 005 0763
LINE FILTER
LINE FILTER
INDUCTOR, 15U K
INDUCTOR, 15U K
CORE, PIPE
Schematic
Location
L623
L625
L801
L811
L812
L821
L851
L901
L1901
Description
Part No.
610 078 5946

652 000 1725
610 078 5946
652 000 1725
645 008 2894
645 016 3104
645 006 2490
645 016 2411
645 006 2490
645 016 2411
645 008 2894
645 016 3104
645 008 2894
645 016 3104
645 060 9596
645 008 2894
645 016 3104
PIPE, CORE
CORE, PIPE
PIPE, CORE
CORE, PIPE
INDUCTOR, 5.6U K
INDUCTOR, 5.6U K
INDUCTOR, 1U K
INDUCTOR, 1U K
INDUCTOR, 1U K
INDUCTOR, 1U K
INDUCTOR, 5.6U K
INDUCTOR, 5.6U K
INDUCTOR, 5.6U K
INDUCTOR, 5.6U K
ASSY, COIL, DEGAUSSING
INDUCTOR, 5.6U K
INDUCTOR, 5.6U K
Schematic
Location
Q401
Q402
Q486
Q490
Q601
Q613
Q627
Q635
TRANSISTORS
Q001
Q005
Q135
Q202
Q208
405 011 8401

405 011 8500
405 011 8609
405 012 2002
405 012 2101
405 012 2309
405 020 7501
405 020 7709
405 020 7907
405 151 8705
405 157 0505
405 008 4805
405 008 4904
405 011 8401
405 011 8500
405 011 8609
405 012 2002
405 012 2101
405 012 2309
405 020 7501
405 020 7709
405 020 7907
405 151 8705
405 157 0505
405 001 7407
405 001 7605
405 004 3109
405 004 3208
405 006 1707
405 006 1806
405 151 3304
406 000 6804
405 001 7407
405 001 7605
405 004 3109
405 004 3208
405 006 1707
405 006 1806
405 151 3304
406 000 6804
TR 2SC1740S-Q
TR 2SC1740S-R
TR 2SC1740S-S
TR 2SC1815-GR
TR 2SC1815-O
TR 2SC1815-Y
TR 2SC945A-PA
TR 2SC945A-QA
TR 2SC945A-RA
TR 2SC536NG-NPA
TR 2SC536NF-NPA
TR 2SB764-E
TR 2SB764-F
TR 2SC1740S-Q
TR 2SC1740S-R
TR 2SC1740S-S
TR 2SC1815-GR
TR 2SC1815-O
TR 2SC1815-Y
TR 2SC945A-PA
TR 2SC945A-QA
TR 2SC945A-RA
TR 2SC536NG-NPA
TR 2SC536NF-NPA
TR 2SA1015-O(SAN)
TR 2SA1015-Y(SAN)
TR 2SA564A-Q(CU)
TR 2SA564A-R(CU)
TR 2SA933S-Q
TR 2SA933S-R
TR 2SA608NF-NPA
TR 2SA1015-GR(SAN)
TR 2SA1015-O(SAN)
TR 2SA1015-Y(SAN)
TR 2SA564A-Q(CU)
TR 2SA564A-R(CU)
TR 2SA933S-Q
TR 2SA933S-R
TR 2SA608NF-NPA
TR 2SA1015-GR(SAN)
Q681
Q693
Q695
Q701
Q711
17
Part No.
405 018 0507

405 018 0606
406 017 4602
405 023 5009
405 023 5306
405 023 5009
405 023 5306
405 148 1801
405 016 9502
405 009 6907
405 009 7003
405 089 0000
405 089 0109
405 011 8401
405 011 8500
405 011 8609
405 012 2002
405 012 2101
405 012 2309
405 020 7501
405 020 7709
405 020 7907
405 151 8705
405 157 0505
405 011 8401
405 011 8500
405 011 8609
405 012 2002
405 012 2101
405 012 2309
405 020 7501
405 020 7709
405 020 7907
405 151 8705
405 157 0505
405 011 8401
405 011 8500
405 011 8609
405 012 2002
405 012 2101
405 012 2309
405 020 7501
405 020 7709
405 020 7907
405 151 8705
405 157 0505
405 001 7605
405 004 3208
405 004 4809
405 041 6507
405 041 6705
405 066 4304
405 066 9903
405 067 0008
405 067 0107
406 000 3605
405 041 6507
405 041 6705
405 066 4304
405 066 9903
Description
TR 2SC3332-R
TR 2SC3332-S
TR TT2168LS-YB11
TR 2SD400-E-MP
TR 2SD400-F-MP
TR 2SD400-E-MP
TR 2SD400-F-MP
TR 2SK2638
TR 2SC3069
TR 2SB985-S
TR 2SB985-T
TR 2SA1707-S
TR 2SA1707-T
TR 2SC1740S-Q
TR 2SC1740S-R
TR 2SC1740S-S
TR 2SC1815-GR
TR 2SC1815-O
TR 2SC1815-Y
TR 2SC945A-PA
TR 2SC945A-QA
TR 2SC945A-RA
TR 2SC536NG-NPA
TR 2SC536NF-NPA
TR 2SC1740S-Q
TR 2SC1740S-R
TR 2SC1740S-S
TR 2SC1815-GR
TR 2SC1815-O
TR 2SC1815-Y
TR 2SC945A-PA
TR 2SC945A-QA
TR 2SC945A-RA
TR 2SC536NG-NPA
TR 2SC536NF-NPA
TR 2SC1740S-Q
TR 2SC1740S-R
TR 2SC1740S-S
TR 2SC1815-GR
TR 2SC1815-O
TR 2SC1815-Y
TR 2SC945A-PA
TR 2SC945A-QA
TR 2SC945A-RA
TR 2SC536NG-NPA
TR 2SC536NF-NPA
TR 2SA1015-Y(SAN)
TR 2SA564A-R(CU)
TR 2SA608-F-CTV-NP
TR 2SC2621-D-RA
TR 2SC2621-E-RA
TR 2SC2621-C-RA
TR 2SC2688(1)-K
TR 2SC2688(1)-L
TR 2SC2688(1)-M
TR 2SC2621-D-RA
TR 2SC2621-E-RA
TR 2SC2621-C-RA
TR 2SC2688(1)-K
Schematic
Location
Schematic
Location
Description
Part No.
Q711 (Cont.)405 067 0008

405 067 0107
406 000 3605
Q721
405 041 6507
405 041 6705
405 066 4304
405 066 9903
405 067 0008
405 067 0107
406 000 3605
Q831
405 002 0308
405 002 0407
405 002 6726
405 002 6924
405 134 5925
405 147 2205
405 163 1503
405 163 2708
Q1071
405 001 7407
405 001 7605
405 004 3109
405 004 3208
405 006 1707
405 006 1806
405 151 3304
406 000 6804
TR 2SC2688(1)-L
TR 2SC2688(1)-M
TR 2SC2621-D-RA
TR 2SC2621-E-RA
TR 2SC2621-C-RA
TR 2SC2688(1)-K
TR 2SC2688(1)-L
TR 2SC2688(1)-M
TR 2SA1037K-T-96-R
TR 2SA1037K-T-96-S
TR 2SA1179-M6
TR 2SA1179-M7-TB
TR 2SA1037AK T146 R
TR 2SA1037AK T146 S
TR 2SA1179N-M6-TB
TR 2SA1179N-M7-TB
TR 2SA1015-O(SAN)
TR 2SA1015-Y(SAN)
TR 2SA564A-Q(CU)
TR 2SA564A-R(CU)
TR 2SA933S-Q
TR 2SA933S-R
TR 2SA608NF-NPA
TR 2SA1015-GR(SAN)
RESISTORS
NOTES:
Read description of the Resistor as follows:
(Example)
CARBON
4.7K J A
1/4W
Rated Wattage
Performance Symbols:
A..General B...Non-flammable
Z...Low noise
Other...Temperature coefficient
Tolerance Symbols:
A...0.05% B...0.1% C...0.25%
D...0.5% F...1% G...2%
J...5%
K...10% M...20%
P...+5 -15%
Rated Value, ohms:
K...1,000
M...1,000,000
Material:
CARBON . . . . . . . .Carbon
MT-FILM . . . . . . . .Metal Film
OXIDE-MT . . . . . .Oxide Metal Film
SOLID . . . . . . . . . .Composition
MT-GLAZE . . . . . .Metal Glaze
WIRE WOUND . . .Wire Wound
CERAMIC RES . . .Ceramic
FUSIBLE RES . . . .Fusible
R001
R002
R003
R004
R005
R006
R013
R106
R107
R131
R133
R135
R137
R142
R143
R151
R161
R162
R163
R164
R166
R167
R201
R208
R209
R212
R251
R252
R272
R273
R274
R276
R281
R284
R287
R288
R289
R321
R353
R400
R401
R402
R405
R406
R409
R411
R421
R422
R423
R426
R428
R441
R442
R443
R444
R449
R471
R472
R481
R482
18
Part No.
401 256 0101

401 256 0101
401 162 2800
401 162 2800
401 150 5905
401 014 4105
401 027 2600
401 008 2001
401 023 2802
401 256 1702
401 255 6401
401 150 6001
401 150 6209
401 256 1702
401 150 6209
401 152 3206
401 150 5806
401 150 5806
401 256 0002
401 150 6209
401 256 7506
401 162 2701
401 026 9600
401 150 6209
401 255 6500
401 256 7100
401 162 3005
401 025 8208
401 256 7308
401 150 5905
401 162 4101
401 024 9701
401 150 5905
401 026 9303
401 255 6500
401 255 6500
401 255 6500
401 150 5905
401 024 7400
401 024 6700
401 012 4503
401 013 4205
401 063 5306
401 007 1104
401 162 4101
402 080 3702
401 286 5305
401 052 6802
401 264 9301
401 256 6905
401 025 1902
401 024 7004
401 150 5905
401 026 9907
401 025 4606
401 265 1700
401 006 7701
401 069 5607
401 010 2600
401 011 9004
Description
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
CARBON
CARBON
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
MT-GLAZE
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
CARBON
CARBON
CARBON
OXIDE-MT
CARBON
MT-GLAZE
OXIDE-MT
MT-FILM
MT-FILM
MT-GLAZE
MT-GLAZE
CARBON
CARBON
MT-GLAZE
CARBON
CARBON
MT-GLAZE
CARBON
OXIDE-MT
CARBON
CARBON
8.2K JA
8.2K JA
1.8K JA
1.8K JA
10K JA
1.5K JA
5.6K JA
18K JA
8.2K JA
33K JA
3K JA
0.000 ZA
1K JA
33K JA
1K JA
330 JA
100K JA
100K JA
120 JA
1K JA
390 JA
180 JA
470 JA
1K JA
100 JA
680K JA
22K JA
22K JA
6.8K JA
10K JA
5.6K JA
12K JA
10K JA
47 JA
100 JA
100 JA
100 JA
10K JA
10K JA
100 JA
100 JA
120 JA
82 JA
1K JA
5.6K JA
6.8 JB
2.4K FA
10K FA
3.3K FA
680 JA
15K JA
1K JA
10K JA
4.7K JA
18K JA
4.7K FA
1 JB
8.2 JA
47 JB
1 JB
1/10W
1/10W
1/10W
1/10W
1/10W
1/4W
1/6W
1/2W
1/4W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/6W
1/10W
1/10W
1/10W
1/10W
1/6W
1/10W
1/10W
1/10W
1/6W
1/10W
1/6W
1/10W
1/10W
1/10W
1/10W
1/6W
1/6W
1/4W
1/4W
1W
1/2W
1/10W
7W
1/6W
1/6W
1/10W
1/10W
1/6W
1/6W
1/10W
1/6W
1/6W
1/10W
1/2W
2W
1/2W
1/4W
Schematic
Location
R485
R486
R487
R488
R489
R491
R492
R493
R494
R495
R497
R499
R503
R504
R505
R506
R507
R508
R509
R511
R517
R518
R601
R602
R603
R604
R605
R607
R608
R609
R610
R611
R612
R613
R616
R617
R618
R619
R627
R628
R629
R630
R631
R632
R634
R683
R692
R693
R694
R695
R699
R701
R703
R704
R706
R707
R711
R713
Part No.
401 025 4606

401 069 5607
401 026 6609
401 059 1602
401 066 5204
401 012 5708
401 156 8504
401 019 4001
401 019 4001
401 061 1706
401 068 1600
401 026 6609
401 026 7002
401 027 5502
401 006 8104
401 027 2303
401 006 7602
401 025 4606
401 027 5502
401 065 2808
401 025 4606
401 256 7209
402 083 6106
402 000 1603
402 088 1502
402 090 2108
401 010 9203
401 066 3002
401 021 5003
402 059 4600
401 150 6001
401 256 3805
401 013 5301
401 027 0309
402 001 8502
401 064 1802
401 150 5905
402 001 7208
401 020 0801
401 162 3005
401 150 5905
401 013 5301
401 150 6209
401 026 3905
401 022 3107
401 150 6209
401 027 0309
401 026 9907
401 025 4903
401 256 5106
401 024 7400
401 162 3005
401 012 7009
401 025 3807
401 256 0309
401 027 8107
401 009 1508
401 065 4604
401 025 3807
401 256 0309
Schematic
Location
Description
CARBON
OXIDE-MT
CARBON
OXIDE-MT
OXIDE-MT
CARBON
MT-FILM
CARBON
CARBON
OXIDE-MT
OXIDE-MT
CARBON
CARBON
CARBON
CARBON
CARBON
CARBON
CARBON
CARBON
OXIDE-MT
CARBON
MT-GLAZE
WIRE WOUND
SOLID
RESISTER
RESISTER
CARBON
OXIDE-MT
CARBON
FUSIBLE RES
MT-GLAZE
MT-GLAZE
CARBON
CARBON
FUSIBLE RES
OXIDE-MT
MT-GLAZE
FUSIBLE RES
CARBON
MT-GLAZE
MT-GLAZE
CARBON
MT-GLAZE
CARBON
CARBON
MT-GLAZE
CARBON
CARBON
CARBON
MT-GLAZE
CARBON
MT-GLAZE
CARBON
CARBON
MT-GLAZE
CARBON
CARBON
OXIDE-MT
CARBON
MT-GLAZE
18K JA
8.2 JA
390 JA
15 JA
22 JA
1K JA
33K FA
390K JA
390K JA
33 JA
4.7 JA
390 JA
3.9K JA
6.8K JA
1.2 JA
560 JA
1 JA
18K JA
6.8K JA
120 JA
18K JA
18K JA
1 KA
3.3M MA
3.3M JA
3.3M JA
560K JA
2.2 JA
560K JA
22 J0.000 ZA
1.5K JA
1.2K JA
47K JA
10 J0.39 JA
10K JA
220 J470 JA
22K JA
10K JA
1.2K JA
1K JA
330 JA
6.8K JA
1K JA
47K JA
4.7K JA
180K JA
560K JA
10K JA
22K JA
10K JA
180 JA
820 JA
82 JA
2.7K JA
12K JA
180 JA
820 JA
1/6W
2W
1/6W
1W
2W
1/4W
1/6W
1/4W
1/4W
1W
2W
1/6W
1/6W
1/6W
1/2W
1/6W
1/2W
1/6W
1/6W
2W
1/6W
1/10W
7W
1/2W
1/2W
1/2W
1/2W
2W
1/4W
1/2W
1/10W
1/10W
1/4W
1/6W
1/2W
2W
1/10W
1/4W
1/4W
1/10W
1/10W
1/4W
1/10W
1/6W
1/4W
1/10W
1/6W
1/6W
1/6W
1/10W
1/6W
1/10W
1/4W
1/6W
1/10W
1/6W
1/2W
2W
1/6W
1/10W
R714
R716
R717
R721
R723
R724
R726
R727
R803
R804
R806
R807
R808
R809
R810
R813
R814
R816
R823
R829
R831
R833
R835
R842
R843
R844
R846
R847
R848
R849
R851
R852
R853
R854
R856
R857
R858
R862
R864
R881
R882
R883
R884
R886
R1001
R1002
R1003
R1004
R1006
R1007
R1051
R1052
R1053
R1054
R1059
R1071
R1073
R1081
R1082
R1083
19
Part No.
401 255 9006

401 009 1508
401 065 4604
401 025 3807
401 256 0309
401 027 8107
401 009 1508
401 065 4604
401 024 6700
401 024 6700
401 162 3708
401 150 5905
401 150 5905
401 162 3708
401 162 3005
401 150 5905
401 150 5905
401 152 3206
401 024 6700
401 024 6700
401 150 5806
401 024 7400
401 256 5908
401 162 4002
401 162 4002
401 162 4002
401 024 7004
401 027 2600
401 027 2600
401 027 2600
401 150 6209
401 162 3401
401 255 6005
401 150 6100
401 024 6700
401 024 6700
401 162 3005
401 255 6500
401 256 0200
401 255 6500
401 255 6500
401 024 6700
401 024 6700
401 150 5905
401 256 2709
401 256 2709
401 150 5905
401 256 6004
401 150 5905
401 256 6004
401 256 2709
401 256 2709
401 024 7400
401 026 1307
401 024 7004
401 026 6609
401 024 6700
401 162 3005
401 162 3005
401 256 6004
Description
MT-GLAZE
CARBON
OXIDE-MT
CARBON
MT-GLAZE
CARBON
CARBON
OXIDE-MT
CARBON
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
CARBON
MT-GLAZE
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
CARBON
CARBON
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
CARBON
CARBON
CARBON
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
82 JA
2.7K JA
12K JA
180 JA
820 JA
82 JA
2.7K JA
12K JA
100 JA
100 JA
4.7K JA
10K JA
10K JA
4.7K JA
22K JA
10K JA
10K JA
330 JA
100 JA
100 JA
100K JA
10K JA
2.7K JA
560 JA
560 JA
560 JA
1K JA
5.6K JA
5.6K JA
5.6K JA
1K JA
39K JA
1M JA
2.2K JA
100 JA
100 JA
22K JA
100 JA
120K JA
100 JA
100 JA
100 JA
100 JA
10K JA
75 JA
75 JA
10K JA
27K JA
10K JA
27K JA
75 JA
75 JA
10K JA
27K JA
1K JA
390 JA
100 JA
22K JA
22K JA
27K JA
1/10W
1/2W
2W
1/6W
1/10W
1/6W
1/2W
2W
1/6W
1/6W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/6W
1/6W
1/10W
1/6W
1/10W
1/10W
1/10W
1/10W
1/6W
1/6W
1/6W
1/6W
1/10W
1/10W
1/10W
1/10W
1/6W
1/6W
1/10W
1/10W
1/10W
1/10W
1/10W
1/6W
1/6W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/6W
1/6W
1/6W
1/6W
1/6W
1/10W
1/10W
1/10W
Schematic
Location
R1084
R1901
R1902
R1903
R1904
R1905
R1906
R1907
R1909
R1910
R3401
R3402
R3406
R3407
R3411
R3421
R3422
R3426
R3432
R3441
R3442
R3443
R3444
R3445
R3446
R3447
R3448
Part No.
401 150 5905

401 150 5905
401 150 6209
401 162 2800
401 150 6100
401 256 7605
401 162 4101
401 256 0408
401 024 7004
401 024 7004
401 162 2909
401 162 2909
401 150 5806
401 255 6005
401 265 4008
401 162 3104
401 255 6401
401 256 7605
401 150 5905
401 256 1405
401 255 6500
401 256 1405
401 255 6500
401 256 1405
401 255 6500
401 256 1405
401 255 6500
Schematic
Location
Description
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
CARBON
CARBON
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
MT-GLAZE
10K JA
10K JA
1K JA
1.8K JA
2.2K JA
3.9K JA
5.6K JA
12K JA
1K JA
1K JA
220 JA
220 JA
100K JA
1M JA
62K JA
3.3K JA
3K JA
3.9K JA
10K JA
330K JA
100 JA
330K JA
100 JA
330K JA
100 JA
330K JA
100 JA
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/6W
1/6W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
SWITCHES
SW1901
SW1902
SW1903
SW1904
SW1905
SW1906
645 006 9673

645 027 7382
645 052 2284
645 006 9673
645 027 7382
645 052 2284
645 006 9673
645 027 7382
645 052 2284
645 006 9673
645 027 7382
645 052 2284
645 006 9673
645 027 7382
645 052 2284
645 006 9673
645 027 7382
645 052 2284

SWITCH, PUSH (VOL )
SWITCH, PUSH (VOL )
SWITCH, PUSH (VOL )
SWITCH, PUSH (CH )
SWITCH, PUSH (CH )
SWITCH, PUSH (CH )
SWITCH, PUSH (CH )
SWITCH, PUSH (CH )
SWITCH, PUSH (CH )
SWITCH, PUSH (MENU)
SWITCH, PUSH (MENU)
SWITCH, PUSH (MENU)
T402
T601
645 049 3775

610 000 1077
652 000 0703
645 060 1224
645 056 7360
645 057 8656
Description
CRYSTAL/FILTERS
X141
X161
X251
X801
421 008 9008

610 015 3059
645 041 1618
610 012 0655
610 204 4195
610 245 9746
645 000 6692
645 021 5483
SAW F TSF5235P
TRAP, CERAMIC 4.5MHZ
TRAP, CERAMIC 4.5MHZ
CRYSTAL OSCILLATOR
CRYSTAL OSCILLATOR
CRYSTAL OSCILLATOR
OSC, CERAMIC 8.00MHZ
OSC, CERAMIC 8.00MHZ
MISCELLANEOUS
A100
A101
A700
A1901
F601
F601A
F601B
K701
K1002
K1011
K1051
PS601
Q901
RL601
SP901
SP902
W601
W902
TRANSFORMERS
T151
T401
Part No.
TRANS, OSC 45.75MHZ

DRIVE, TRANS
TRANS, DRIVE
TRANS, FLYBACK
TRANS, POWER, PULSE
TRANS, POWER, PULSE
20
610 306 8077

645 052 6077
645 052 6084
610 306 8084
645 047 6228
423 007 1601
423 007 1809
423 018 8101
423 029 8008
645 000 5077
645 016 0479
645 000 5077
645 016 0479
645 025 6103
645 028 0306
645 038 1904
645 051 1271
645 007 1584
408 046 5209
414 012 3209
645 000 4155
645 011 2713
645 015 8629
645 024 7767
645 024 7828
645 052 5933
645 040 8618
652 000 0656
645 040 8618
652 000 0656
645 023 1681
645 056 9531
610 306 8282
ASSY, PWB, MAIN

TUNER, U/V
TUNER, U/V
ASSY, PWB, SOCKET
UNIT, REMOCON RECEIVER
FUSE 125V 4A
FUSE 125V 4A
FUSE 125V 4A
FUSE 125V 4A
HOLDER, FUSE
HOLDER, FUSE
HOLDER, FUSE
HOLDER, FUSE
SOCKET, CRT 8P
SOCKET, CRT 8P
JACK, RCA-3
JACK, RCA-3
SOCKET, DIN 4P
TH PTDAA1BF3R0Q100
CRT A51QDX992X003
RELAY
RELAY
RELAY
RELAY
RELAY
RELAY
SPEAKER, 8
SPEAKER, 8
SPEAKER, 8
SPEAKER, 8
CORD, POWER
CORD, POWER-2.0MK
ASSY, WIRE GND CONNECTOR
CABINET PARTS LIST
6
5
4
3
2
1
8
9
MENU
CH
- VOL +
POWER
AS
12
11
10
13
ACCESSORY PARTS LIST
CABINET PARTS LIST

KEY NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
PARTS NO.
610 306 5267
610 268 9648
412 053 3905
OR 412 054 0002
610 102 7151
610 306 5298
412 036 1805
OR 411 078 1101
412 018 8402
610 306 5007
610 289 5148
610 299 5527
610 285 5685
610 306 5342
610 306 5311
DESCRIPTION
KEY NO.
CABINET FRONT ASSY

CRT SPACER 2.0 MM (4 USED)
DC HOLDER (2 USED)
CABINET BACK
SCREW 4X14 (7 USED)
SCREW 4X14 (7 USED)
SCREW 3X10 (1 USED)
BUTTON UNIT
CAP RC
DEC SHEET
SANYO BADGE-SMALL
DEC AV SHEET
DOOR
PARTS NO.
610 306 8749
610 309 7138
610 309 7145
645 051 8485
645 051 8539
610 290 1221
610 290 1283
21
DESCRIPTION
OWNERS MANUAL (ENG)
OWNERS MANUAL (SPA)
OWNERS MANUAL (FRE)
RC TRANSMITTER
RC TRANSMITTER
RC BATTERY COVER
RC BATTERY COVER
J201
E
Q202
J216
C212
L164
J441
C153
R006
L136
C151
KS
L811
L812
R848
R846
R849
R847
Q001
J803
R013
J852
J851
C012
C284
J134
C147
C272
J841
R284
C274
J843
J842
E Q490
C131
Q135
J131
R833
R832
C628
J618
D422
J141
L146
R803
J142
R804
R276
J453
R400
J447
J449
J448
J445
L284
J493
J492
R499
C497
J446
D490
J1011
J1013
J401
J402
DIP
L141
R144
J102
R422
J849
J276
J847
R856
J846
R857
J1081
J1006
J1007
R503
D429
R421
J1004
J1083
J1082
TP113
J848
D801
J1014
D806
R517
IC501H3
J494
R106
C516
J502
C502
C407
J113
J114
Q1071
R107
R1071
R509
C102
L401
J407
D101
R1053
R1054
J1053
C1081
L1001
J409
C101
J116
J117
D1051
D1052
J1051
D428
R428
J104
C106
D482
C416
C416A
C414
R482
J413
C511
R510
C511A
R497
C484
V-ADJ.UP
R497A
V-ADJ.DOWN
IC501H2
R513
R507
R505
R1059
D1001
J1052
C1051
C1001
C503
J412
J411
Q402
R511A
R511
H-OUT
C1059
L501
R512
D502
J501
C501
C504
16
TUNER
IC501
R508
R506
R504
J1001
J1003
R1072
R430
L402
C506
IC1081
D501
C473
R416
R406
Q401
C406
L401A
R514
R1073
R404
C417A
C408
L404
D408
R481
R353
C418
J211
R201
X161
X251
C403
C256
C221
C426
C401
C405
C509
R884
C829
CPU
Q005
C624
D624
C622
R405
R494
R485
D487
R408
C258
C253
D351
L801
D843
X801
C851
C489
Q486
C626
D486
R489
L623
D623
R699
C211
J209
L256
Q208
R252
C421
C252
D421
R441
R443
R401
R444
C505
J812
J443
R829
R402
R823
R883
C822
C856
J624
R486
C853
D836
J802
R489A
D625
C623
L626
C482
D481
C481
R405A
C015
C3435
C3437
C3448
J3471
C3442
J144
C3441
J3401
J017
D472
KSP
AUDIO OUT
C001
1 D001
C002
C3427
C3447
J809
C802
C811
L821
R683
L851
J482 R487
J481
L625
C625
10
10
C608
C493
R491
J111
TE7
A101
IC001
J690
J3402
C3424
C3418
1B
C010
C011
C3411
C3417
C3416
C3413
J3403
PS
60
J013
C3414
C3412
J3404
C3439
C3432
J814
D834
L863
C806
J811
L3401
16
R612
C608A
R471
K1002
K1001
C3408
C3436
R630
T601A
T601
C611
R493
R492
D471
C471
22
C3404
C3401
C629
IC601
Q695
16
L602A
R604
R611
Q601H1
KX
TP10
R617
D611
L611
J808
R1910
R1909
C634
R694
J614
L602
R606
Q611
R610
L612
Q612
B10B09900 A
NA7C
KX5P
KX4P
TUNER
HLC
C1002
C683
C693
Q693
C630
R631
3
J616
R605
D614
R603
E
J606
D613
C614
T402H10
C1901
Q681
R692
D693
R601H3
C604
R607
C613
E
C612 R614
Q613
C417
D1002
E
D629
D680
E Q627
R634
D601
D602
C603
D603
D604
R618
C412A
K1051
KY1P
D1902
IC681A
IC681
R686
E
Q635
R601H2
C606A
T402A
J1907
J601
E
D627
R601A
A2
C606
R602
T402H7
AV
T402H1
K1003
L413
C411
T402H9
KX3P
KX1P
????
R628
R601H1
R601
A1
R411
T402H6
TP301
LF601
J608
C601
T402H11B
L1901
D683
C601C C601B
T402H2
T402H8
C412
T402H3
T402H12
TJ3
T402H4
T402H5
T402B
T402H11
R412
TP317
TP132
KT3P
X141
TJ6
R488
C633A
1
R495
V-OUT
CLK
KB 4
KY
FBT
KTP
R495A
B10B0990A A
KT5P
T402
TP50
ACK
IC501H1
T401A
1
4
TP34
C633
Q601H2
TJ1
T151
8
TJ5
J112
KT4P
R407
STA
TUS
T601H7
IC802
5
T601AH11
R472
IVC
R615
T601AH14
NA7C
KT1P
T601H2
TJ2
R613
R635
D612
POWER-CIRCUIT
C609H2
C632A
TP7
GND
C632
C609H1
D1901
C601A
C609
K1011
F-AV
F601A
KD
C1902
C631
C631A
F601B
PS601A
TP318
4A 125V
T401
R498
KT2P
PS601
SW1905
MTS
4A-125V
SW1904
SW1903
SW1902
ATTENTION : POUR MAINTENIR LA PROTECTION CONTRE

LES RISQUES D INCENDIE UTILISER UN FUSIBLE DE
4A 125V
SW1906
CH-DN
SW1901
FOR CONTINUED PROTECTION AGAINST A RISK OF FIRE,

REPLACE ONLY WITH THE SAME TYPE 4A, 125V FUSE.
CAUTION
MENU
CH-UP
VOL-DN
VOL-UP
A1901
POWER
RL601
HDT
TP51
DATA
KD1P
KD2P
POWER-TRANS
Q601
LF601B
LF601A
D699
COMPONENT AND TESTPOINT LOCATIONS

MAIN BOARD PARTS SIDE
B10B09900
A
NA7C
4
23
TJ3
C416A
C416
R411
J407
KB
KX5P
R3437
C417
X
C412A
C412
C411
T402H4
L413
KX3P
T402H3
R412
T402H5
T402H2
T402
T402H7
T402H6
L611
Q612
R609
R619
R616
R607
T402H11
Q613 E
C612
R614
D613
R618
C613
J609
J610
D614
C609H1
C614
L612
J605
J604
C604
D604
X
R602
C606
X
C606A
R601H2
A2
R601
Q627
R601A
E
D627
R610
J606
R603
R606
R629
R692
C683
C3436
48
24
C3416
12
13
C3401
A1
R691
J608
C601C
J603
E R628
R601H1
C3408
J3404
C3412
R3411
C3414
C3411
TP301
C011
C010
R3401
C3404
10
Q681 E
20
C3413
J3403
R3422
R3421
C3418
C3417
C004
J3402
IC
34
01
KD
Q601H1
D611
Q611
J613
J615
R608
D603
D602
C603
R601H3
40
KD2P
C884
D884
R611
R617
R604
R605
J619
D601
ER634
C693
R693
D693
E Q693
C634
25
KD1P
R471
C471
Q601H2
R491
C633A
D471
C633
C493
C611
C608A
J611
R694
Q635
IC601
37
30
C003
IC001
LF601
D881
R407
R485
R495
R492
D487
T601H7
C608
T601H2
J614
C632A
R493
T601AH14
R494
T601AH11
T601
R631
C632
C481
R695
Q695
C3439
C3432
36
C3427
R353
T401
J616
D481
L602
2
1
L602A
D612
R612
TJ5
T601A
R630
C629
R481
C482
77
J481
C002
C3424
C001
C015
D001
R627
D408
L404
C821
C630
R683
L851
L3401
J482
J811
R635
16
16
R489
J802
C806
C822
L863
D834
R1909
R1910
C3447
R632
R405
C625
D625
R489A
R487
D836
C853
C854
R814
R816
C811
L821
J814
J808
J809
C3435
R3433
R3432
TP317
C3437
R003
C006
IC681A
C800
C1901
C601
C601A
J601
D683
F601A
C689
R1901
C601B
J1907
C631A
X X
C631
C1902
D1901
F601B
L1901
C1002
R3442
R3441
R3443
R3444
J013
D629 IC681
D680
R686
D1002
D1902
R1002
POWER
R404
R005
10
L625
D486
R486
J624
R853
C858
R801
IC801
R813
D843
C802
R883
L801
R402
J443
R401
J812
C505
J3471
C3448
C3442
C3441
TP318
C408
10
Q486
L626
C856
J005
C857
C852
R858
20 21
22
C829
R823
R829
D351
C402
R444
R443
R441
D421
J144
C252
R252
C421
R001
R002
J017
J3401
D472
KSP
C3434
C3433
Q401
T401A
C407
C623
L623
C626
C489
Q005
C851
X801
10
C862
30
J813
R862
R881
R882
C405
C441
C427
C401
R251
C253
J209
L256
J018
C3431
R406
J618
C622
D624
C624
Q001
42 40
R884
J881
C509
C282
R442
C426
C256
R321
R281
40
41
C251
R209
C221
Q208
C211
J211
C3422
SW1901
R430
C406
J402
J401
R488
IC501H3
R416
J1013
C628
E
R006
J803
C012
J804
TJ1
J409
L401A
L401
J1014
J1011
R833
C835
R510
C473
R106
R832
D490
R495A
C511
L402
C404
R013
J852
J851
R852
C511A
R511
IC501H2
J493
R835
R844
R842
R843
R847
C807
C810
30
C403
R851
J411
J494
IC501H1
J492
R849
R848
J441
25
50
R854
R1902
J413
K1003
L501
D501
R499
TJ6
J412
R512
R517
Q490 E
R810
24
R212
X251
R221
C257
J216
C258
X161
R201
J201
Q831
R511A
R3436
R518
C497
L812
L811
KS
R886
J501
D801
J446
R846
C809
D806
L284
J445
C285
J842
J843
C842
TP36
20
R289
R806
R809
R513
C516
J502
J449
J448
J447
R400
J453
R287
R288
IC501
C508
C506
C502
D429
R503
J1007
C841
D482
FIX
-R
C501
D502
R506
R509
R514
R284
J841
C284
60
C212
R211
Q202 E
R497
FIX
-L
D831
R497A
K1001
R508
J1001
R276
R273
IC
10
1
10
R165
C808
R507
V-IN
C801
TJ2
R408
R482
AUX2-R
R505
R1001
R3447
R504
R1006
R1007
R1081
R1082
R1004
C503
C504
J1002
J1006
C272
64
C153
R807
R808
R831
C418
K1002
R421
J1004
J1083
J1082
C131
TP35
IC802
R428
D1059
L1001
R272
C1059
R1003
C843
R161
R134
R3445
IC1081
C274
R274
C484
R1051
R409
C414
K1051
J1003
R1084
R162
C803 C161
C804
R803
C147
70
65
L164
A
R164
PB2
R3435
C1081
1
16
R804
J142
80
R133 L136
PB3
J414
R1052
R3434
C1001
R857
R856
J1081
TP113
J131
R131
R3448
C1071
R1073
R1071
R137
C135
C132
R1059
R1054
R1083
R1072
L146
J141
R135
C142
R142
R166
R163
B10B0990A
C151
R282
D428
R3446
SCL
J1052
D1001
J1053
J847
J276
J846
R141
C141
J134
C143
R143
J1051
MB
R1053
J112
J848
J102
L141
R144
D422
D1052
TB
J1071
J849
TP132
C1052
Q1071
R107
J114
R422
X141
D1051
C102
C103
R103
J113
C134
AUX2-L
EN
C1051
A101
C146
R449
T402A
J111
J104
C101
D101
SDA
C106
AGC
J117
C812
C813
PB
R167
1
J217
R864
TP7
R423
R472
R1903
IF
R426
SW1902
D699
R151
R3426
R405A
TE7
+
SW1903
D623
Q135
C3426
R1906
C152
C138
R136
C136
C133
C137
C3423
SW1904
VOL-UP
1B
TP10
T151
+
PB
R1904
60
PS
J021
R3407
SW1905
VOL-DN
R004
PB
C3403
C3402
R3402
R1907
CH-UP
R699
R208
C3421
R3406
C3406
C3407
R1905
PB
SW1906
C417A
K1011
CH-DN
MENU
J690
J116
MAIN BOARD FOIL SIDE

A1901
J1901
RL601
LF601A
LF601B
PS601
PS601A
C609
C609H2
R613
Q601
R615
J622
TP51
C883
D883
TP50
C1080
T402H8
T402H12
T402H11B
T402H1
T402H9
T402H10
PB1
KX1P
T402B
KY1P
1
KX4P
MAIN BOARD COMPONENTS AND TEST POINTS GRID LOCATIONS
Part
Loc.
Part
Loc.
Part
Loc.
Part
Loc.
Part
Loc.
Part
Loc.
D429
D612
D801
IC001
IC101
IC501
IC601
IC681
E2
B5
D3
F6
E4
D2
C5
C6
IC801
IC802
IC1081
IC3401
Q001
Q005
Q135
Q202
D4
E4
E2
E5
D4
D4
F3
F4
Q208
Q401
Q402
Q486
Q490
Q601
Q613
Q627
F5
B2
C2
D4
D3
A3
A4
C6
Q635
Q681
Q693
Q695
Q831
Q1071
R512
R513
B5
C6
B5
B5
D5
F2
D1
D1
TE7
TP7
TJ1
TJ6
TP16
TP21
TP50
TP51
F2
F3
C3
D3
F4
F3
A2
A2
TP317
TP318
T151
E5
E5
F4
KT1P
R498
D882
X
KT2P
X
KT3P
X
KT4P
X
KT5P

PICTURE TUBE SOCKET BOARD
Q701
C702
R707A
B10B0990B
R701
1
R706
Q701A
R707
K7B
R717
(-)
9V HEATER +B
R704
R717A
R727
R727A
R716
R726
????
K7U1
SCREEN
Q721
Q721A
C742
K701
E
Q711
R711
5 (-) (-)
R724
R721
Q711A
K7S
GND
K7Y1
G R1
PIC TUBE SOCKET BOARD COMPONENTS

Part
Loc.
Q701
Q711
Q721
N/A
N/A
N/A

July / 2003 / 2000 SMC
Printed in U.S.A.
24
MODEL DS20930
WAVEFORMS
CAUTION
SCHEMATIC DIAGRAMS

BLOCK DIAGRAM
NOTES ON SCHEMATIC DIAGRAMS
1. All resistance values in ohms K=1,000 M=1,000,000.
2. Unless otherwise noted on schematic, all capacitor values less than 1 are expressed in F (Micro Farad),
and the values more than 1 are in pF.
3. Unless otherwise noted on schematic, voltage reading taken with VOM from point indicated to chassis
ground. Voltage reading taken using color-bar signal VHF channel 5, all controls at normal. Line voltage at 120
volts. Some voltages may vary with signal strength.
4. Waveforms were taken with color-bar signal and controls set for normal picture. Waveforms marked with
an may vary with signal strength.
5. The Symbol
indicates a fusible resistor, which protects the circuit from possible short circuits.
SERVICE NOTES:
1. When replacing parts on circuit boards, clamp the lead wires to terminals before soldering.
2. When replacing high wattage resistors on circuit board, keep the resistor body 10 mm (3/8) from circuit board.
3. Keep wires away from high voltage and high temperature components.
4A 125V
Note: Voltages were measured with offset color-bar signal and controls set for normal picture.
SDL
SCL
A101
UHF/VHF TUNER
WITH PLL
& BAND SW
H-S
IF
AGC
BUS SCL
BUS SDA
IC802
EEPROM
IIC SCL
IIC SDA
28
V-S
34
38
35
32
33
Q135
BUFFER
IC101
SIGNAL PROCESS
MUTE
SDA 9
S SW
X141 78/79
SAW
FILTER
RF AGC 77
11
ACL
Y 52
RC IN
S/COMP SW
AV1/AV2 SW
31
SW1901-1906
CONTROL KEYS
KEY IN
10
30
X IN
19
C808
MARK
B
EC
Y 54
K
K
A
A
29
RL601
RELAY
BC
EC
3
27
TOP VIEW
C
B ... BASE
1
12
32
IN
(1)
OUT
GND (3)
(2)
C ... COLLECTOR
E ... EMITTER
B
AC120V
60Hz
F601
AC
FUSE
11
Q601
SW.
C601
CHIP RESISTORS
TOP VIEW
S-Y 1
L
H
V1/V2 2
S-C 3
INT-V 5
V 14
1.0V HORIZ
K1001
REAR
AV IN
(AV2)
IC501- 5
(Vertical Output)
IC501- 1
(Inverting Input)
Q202-E (TP16)
(Internal Video)
Q401- B
(Horizontal Drive)
48 VERT
0.6V VERT
1.0V HORIZ
.7V HORZ
Q402- B
(Horizontal Output)
Q601- G
(Power Switching)
T402- 9
(Heater)
21V HORZ
15V 50KHz
28V HORIZ
Q202
BUFFER
Q001
POWER OFF
NOISE
CANCEL
4.5MHz L164
SOUND X161
TRAP
VIDEO
SW.
V
SYNC
SEP.
49
36
V-S
37
H-S
33
H-PULSE
26
BPA
COLOR
DEMOD
IC501
VERT.
OUTPUT
Q401
HORIZ.
DRIVE
30
5
ABL
1
6/7
H.V.
T402
HORIZ.
FOCUS
OUTPUT
SCREEN
TRANS.
HEATER
9
T401
H-DRIVE
TRANS.
BLACK
STRETCH
DEFLECTION
YOKE
L902
5
1
Q402
HORIZ.
OUTPUT
8
4
SHARP
40
HOLD DOWN
CONT
BRITE
12
Q721
-R OUT
Q711
-G OUT
Q701
-B OUT
IC001
AUDIO
AMP. 3
SP901
LEFT
SPEAKER
SP902
RIGHT
SPEAKER
LOW +B
HOLD DOWN
DETECT.
R
K1011
FRONT
AV IN
(AV 1)
AUDIO IN-1 (R)
H
HORIZ.
DRIVER
Q1071
BUFF.
D482
17
13
Q831
RESET
VIDEO IN-1
AUDIO +B
ABL
AUDIO IN-1 (L)
DELAY
LINE
C 4
Q005
AUDIO +B
SWITCH
56 VIDEO
VIDEO
DET.
Y 15
AFT S-CURVE
OSD
SW.
14
RGB
OUT
18
Q901
PIX TUBE
19
15
POWER FAIL
TJ1
D612
PHOTO
COUPLER
+130V
D627
26V
Q681
12V SW
DRIVE
Q635
OVERLOAD
PROTECT.
Q693,
Q695
AUDIO +B
D471
D802
12V
+12V
26V
15V
5V
ALWAYS
IC681
5V REG.
IC601
POWER
REG.
+200V
POWER
ON/OFF
Q613
ERR.
AMP.
4A 125V
V1 12
RESET
D624
D623
D601-D604
FULL WAVE
RECTIFIER
A....ANODE
K....CATHODE
V2 13
75
FM
DET.
CAP
VIDEO
OUT
Y CV IN
OSD (R)
OSD (G)
OSD (B)
OSD (BLK)
T601
CONVERTER
TRANS.
D625
LF601
LINE
FILTER
INFRARED EMITTING
B ... BASE
C ... COLLECTOR
E ... EMITTER
CHIP TRANSISTORS
E
BC
3.4V HORIZ
D481
PS601
POSISTOR
L901
DEGAUSING
COIL
K
A
SIDE VIEW
17
42
41
40
39
Q208
9/10
X 801
25
1
COUNT TERMINALS IN
ARROW DIRECTION
20
IC1081
VIDEO SWITCH
BEAM
VOLTAGE
DETECT.
ABL-IN
IC801
CPU
WITH
CAPTION
DECODER
+12V
B
B
E C
EC
B
EC
X OUT
DIODES
BUS
INTERFACE
SCL 10
EXT. VIDEO
A1901
RC PRE-AMP
C809
3.4V HORIZ
AUDIO IN-2 (R)
THIS TV CONTAINS CRITICAL PARTS TO PROTECT AGAINST X-RADIATION. NOMINAL 2ND ANODE VOLTAGE IS
29.1KV AT ZERO BEAM CURRENT AT 120 VOLTS AC LINE, AND MUST NOT EXCEED 31.1KV UNDER ANY
OPERATING CONDITION. SEE HIGH VOLTAGE CHECK ON PAGE 8.
AUDIO IN-2 (L)
ANT
X-RADIATION WARNING NOTE
TOP VIEW
3.4V HORIZ
LS OUT-R
TP 16
INT. VIDEO
TOP VIEW
IC101- 52
(Video Input)
VIDEO IN-2
RF AGC
TRANSISTORS
33 34 36 37
13
K1051
S-VIDEO IN
(AV 2)
PHOTO COUPLERS
IC101- 19
(B-Output)
Y
C
S-SW
THE COMPONENTS DESIGNATED BY A STAR () ON THIS SCHEMATIC DIAGRAM DESIGNATE COMPONENTS

WHOSE VALUES ARE OF SPECIAL SIGNIFICANCE TO PRODUCT SAFETY. SHOULD ANY COMPONENT
DESIGNATED BY A STAR NEED TO BE REPLACED, USE ONLY THE PART DESIGNATED IN THE PARTS LIST. DO NOT
DEVIATE FROM THE RESISTANCE, WATTAGE AND VOLTAGE RATINGS SHOWN.
INTEGRATED CIRCUITS
IC101- 18
(G-Output)
4 LS OUT-L
IC3401
MTS DECODER
IC101- 17
(R-Output)
Q486
9V REG.
Q627
12V SW.
STANDBY MODE
ALWAYS +5V
CONTROL
Q490
5V REG.
9V
TJ5
D801
D428
(13V)
D429
ANODE LEAK
DETECT.
(7V)
5V
B6
R428
12 x 10 3 = 12K ohm
g7taa
123
VOLTAGE CHARTS
NOTE: Voltages were measured using color-bar signal and the controls set for normal picture.
Device/Pin #
D612-1
CAPACITOR AND RESISTOR CODE CHART

D612-2
CAPACITOR (Example)
D612-3
500 C K 1500 B
D ...........................
T ............................
J ............................
K ...........................
M ...........................
N ...........................
P ...........................
Z ...........................
C ...........................
C ...........................
E ...........................
F ...........................
N ...........................
T ............................
K ...........................
H ...........................
P ...........................
M ...........................
Characteristics
Value code
Tolerance code
Material code
Voltage rating
0.5pF
+50% 10%
5%
10%
20%
30%
+100% 0%
+80% 20%
0.25pF
Ceramic
Electrolytic
Polyester
Polypropylene
Tantalum
Ceramic
MT-Composite
NP. Electrolytic
MT-Polypropylene
RESISTOR (Example)
6 Y K 4.7
D ...........................
F ...........................
G ...........................
J ............................
K ...........................
M ...........................
F ............................
N ...........................
S ...........................
Y ...........................
C ...........................
D ...........................
W ..........................
Value code
Tolerance code
Material code
Wattage rating
25
0.5%
1%
2%
5%
10%
20%
Fusible
Metalized Carbon
Oxide Metalized
Wire Wound
Solid
Carbon Film
Wire Wound
D612-4
IC001-1
IC001-2
IC001-3
IC001-4
IC001-5
IC001-6
IC001-7
IC001-8
IC101-1
IC101-2
IC101-3
IC101-4
IC101-5
IC101-6
IC101-7
IC101-8
IC101-9
IC101-10
IC101-11
IC101-12
IC101-13
IC101-14
IC101-15
IC101-16
IC101-17
IC101-18
IC101-19
IC101-20
IC101-21
IC101-22
IC101-23
IC101-24
IC101-25
IC101-26
IC101-27
IC101-28
IC101-29
IC101-30
IC101-31
IC101-32
IC101-33
IC101-34
IC101-35
Device/Pin #
Volts/Mode
POWER ON:
25.7
POWER ON:
24.8
POWER ON:
0.7
POWER ON:
14.7
6.7
15.4
N.C.
GND
N.C.
1.4
1.4
GND
GND
GND
GND
GND
GND
5.1
2.1
2.7
3.8
3.6
4.3
1.5
1.5
1.4
0.2
8.2
2.5
2.2
2.4
GND
GND
GND
GND
GND
N.C.
2.1
2.6
5.3
2.7
0.4
GND
N.C.
1.0
1.8
N.C.
POWER OFF:
9.6
POWER OFF:
8.0
POWER OFF:
0.4
POWER OFF:
1.7
IC101-36
IC101-37
IC101-38
IC101-39
IC101-40
IC101-41
IC101-42
IC101-43
IC101-44
IC101-45
IC101-46
IC101-47
IC101-48
IC101-49
IC101-50
IC101-51
IC101-52
IC101-53
IC101-54
IC101-55
IC101-56
IC101-57
IC101-58
IC101-59
IC101-60
IC101-61
IC101-62
IC101-63
IC101-64
IC101-65
IC101-66
IC101-67
IC101-68
IC101-69
IC101-70
IC101-71
IC101-72
IC101-73
IC101-74
IC101-75
IC101-76
IC101-77
IC101-78
IC101-79
IC101-80
26
Volts/Mode
5.0
4.3
4.7
GND
0
GND
GND
GND
2.3
3.6
2.1
3.1
GND
2.5
GND
GND
2.6
5.1
2.9
2.6
2.5
GND
3.6
4.4
4.4
GND
GND
GND
GND
2.4
2.2
2.2
2.4
3.2
GND
GND
GND
2.3
GND
2.2
2.6
2.2
2.9
2.9
GND
Device/Pin #
IC501-1
IC501-2
IC501-3
IC501-4
IC501-5
IC501-6
IC501-7
IC601-1
IC601-2
IC601-3
IC681-1
IC681-2
IC681-3
IC801-1
IC801-2
IC801-3
IC801-4
IC801-5
IC801-6
IC801-7
IC801-8
IC801-9
IC801-10
IC801-11
IC801-12
IC801-13
IC801-14
IC801-15
IC801-16
IC801-17
IC801-18
IC801-19
IC801-20
IC801-21
IC801-22
IC801-23
IC801-24
IC801-25
IC801-26
IC801-27
IC801-28
IC801-29
IC801-30
IC801-31
IC801-32
IC801-33
IC801-34
IC801-35
IC801-36
Volts/Mode
Device/Pin #
2.5
25.9
2.9
GND
18.0
26.5
2.6
130.0
24.8
GND
13.4
GND
5.0
4.0
4.9
4.9
0
0
0.3
0
0
0
4.9
GND
4.8
GND
4.9
1.9
0.2
2.1
GND
2.2
2.0
GND
4.9
GND
GND
4.9
0.3
POWER ON:
4.9
2.4
2.8
0
4.9
3.6
4.9
3.7
4.8
4.9
POWER OFF:
IC801-37
IC801-38
IC801-39
IC801-40
IC801-41
IC801-42
IC802-1
IC802-2
IC802-3
IC802-4
IC802-5
IC802-6
IC802-7
IC802-8
IC1081-1
IC1081-2
IC1081-3
IC1081-4
IC1081-5
IC1081-6
IC1081-7
IC1081-8
IC1081-9
IC1081-10
IC1081-11
IC1081-12
IC1081-13
IC1081-14
IC1081-15
IC1081-16
IC3401-1
IC3401-2
IC3401-3
IC3401-4
IC3401-5
IC3401-6
IC3401-7
IC3401-8
IC3401-9
IC3401-10
IC3401-11
IC3401-12
IC3401-13
IC3401-14
IC3401-15
IC3401-16
IC3401-17
IC3401-18
IC3401-19
IC3401-20
IC3401-21
Volts/Mode
4.9
4.8
0.2
0
0
0
GND
GND
GND
GND
4.9
4.9
GND
5.0
2.5
2.9
2.5
2,4
2.4
GND
GND
GND
0
0
0
2.9
2.5
2.9
2.9
9.3
4.1
4.1
4.1
4.1
3.6
3.7
GND
4.1
4.1
4.1
4.1
4.9
4.1
1.3
1.3
0
GND
3.2
9.1
0
4.1
Device/Pin #
IC3401-22
IC3401-23
IC3401-24
IC3401-25
IC3401-26
IC3401-27
IC3401-28
IC3401-29
IC3401-30
IC3401-31
IC3401-32
IC3401-33
IC3401-34
IC3401-35
IC3401-36
IC3401-37
IC3401-38
IC3401-39
IC3401-40
IC3401-41
IC3401-42
IC3401-43
IC3401-44
IC3401-45
IC3401-46
IC3401-47
IC3401-48
Q001-B
Q001-C
Volts/Mode
Q486-B
Q486-C
Q486-E
Q490-B
Q490-C
Q490-E
4.1
3.7
3.9
4.1
4.1
4.1
1.9
4.1
4.1
2.0
4.1
4.1
4.1
0
4.1
4.1
4.1
4.1
4.1
4.1
GND
4.1
4.1
4.2
GND
4.1
4.1
POWER ON:
0.7
POWER ON:
Q001-E
Q005-B
Q005-C
Q005-E
0
GND
15.4
16.0
16.1
Q135-B
Q135-C
Q135-E
Q202-B
Q202-C
Q202-E
Q208-B
Q208-C
Q208-E
Q401-B
Q401-C
Q401-E
Q402-B
Q402-C
Q402-E
2.2
5.0
1.5
1.7
GND
2.3
2.5
GND
3.1
0.3
17.7
GND
3.2
N/A
3.2
27
Device/Pin #
Q601-G
Q601-D
Q601-S
Q613-B
Q613-C
Q613-E
Q627-B
Q627-C
Q627-E
Q635-B
Q635-C
POWER OFF:
0
POWER OFF:
17.0
Q635-E
Q681-B
Q681-C
Q681-E
Q693-B
Q693-C
Q693-E
Q695-B
Q695-C
Q695-E
Q701-B
Q701-C
Q701-E
Device/Pin #
Volts/Mode
9.9
11.6
9.2
5.9
6.7
5.2
POWER ON:
5.8
POWER ON:
157
POWER ON:
15
POWER ON:
0.2
POWER ON:
4.7
GND
POWER ON:
12.7
POWER ON:
13.2
POWER ON:
13.3
POWER ON:
3.4
POWER ON:
25.0
POWER ON:
3.4
POWER ON:
0.7
POWER ON:
0
GND
POWER ON:
0.5
POWER ON:
24.7
POWER ON:
0.6
POWER ON:
24.7
GND
POWER ON:
24.8
2.4
154.9
2.2
POWER OFF:
0.4
POWER OFF:
164
POWER OFF:
Q711-B
Q711-C
Q711-E
Q721-B
Q721-C
Q721-E
Q831-B
Q831-C
Q831-E
Q1071-B
Q1071-C
Q1071-E
Volts/Mode
2.4
158.0
2.2
2.3
159.0
2.2
4.2
4.9
4.9
3.0
GND
3.7
POWER OFF:
0.1
POWER OFF:
0.1
POWER OFF:
8.0
POWER OFF:
0
POWER OFF:
8.0
POWER OFF:
1.3
POWER OFF:
8.2
POWER OFF:
1.1
POWER OFF:
0
POWER OFF:
6.0
POWER OFF:
5.2
POWER OFF:
7.1
POWER OFF:
4.7
POWER OFF:
7.4
POWER OFF:
8.0
28
MODEL DS20930

TUNER
C1051
16EM22LBWA
A101
10
AGC
MB
IF
9V
L1001
J
C101
6.3EM
470LBWA
J1002
1/10GZ0C
R1007
1/10GJ
27KC
R1004
1/10GJ
27KC
K1051
R1003
1/10GJ
10KC
C Y
GND GND
10
9
R1052
1/10GJ75C
R1059
1K
S-SW
C IN
C1059
16EM10LBWA
C1080
KZ0.1LZF
C1081
16EM10LBWA
5VB6
R857
100
C1052
KK0.01LZB
R1081
1/10GJ22KC
J1003
J
J1053
J
R856
100
R1082
1/10GJ22KC
12
AV1/AV2 SW
15 16
17 18
Y IN
R1051
1/10GJ75C
S/COMP SW
13
D1051
GND
14
PB
TU+B
DATA
CLK
F1BAM0280
:F1BAM0290
D1052
7
8
S-VIDEO OUT
6 2 4 3 1 5
S-GND
D1059
R1006
1/10GJ
10KC
R106
R107
DJ8.2K 1/2DJ18K
14
13
<CV OUT>
12
11
10
R208
1/10GJ1KC
41
R809
1/10GJ R810
4.7KC 1/10GJ22KC
6
IC802
VER
C/D
80
IF-GND
X141
SF5235P
C146
KK0.01
LZB C147
SDA,SCL
BUS
TP20
L141
J
R131
1/10GJ
33KC
C131
EM1 R803
LBWA 100
6.3EM100LBWA
R161
1/10GJ100KC
C161
KZ0.1
LZF
R162
1/10GJ
100KC
R823
100
ABL
DRIVE/
CUT-OFF
CLAMP
10
E/W
11
12
13
C843
KZ0.1
R273 C272 LZF
1/10GJ EM3.3
LBWA
R804 10KC
100
R274
1/10GJ
5.6KC
14
C842
KZ0.1
LZF
15
5V
L146
J
R864
1/10GJ
120KC
C505
63GJ0.47
LBZA
33
SDA
VCAWGT
32
18
19
20
21
22
23
24
VCATC
31
DGND
VCAIN
30
MAININ
VEOUT
29
MAINOUT
VETC
28
VEWGT
PCINT1
PCINT2
PLINT
14
C284 C285
16EM47 KK0.01
LBWA LZB
Q490
2SD400
E-MP
C497
6.3EM
100LBWA
R284
47
D490
5VB6
20
21
22
C3423
10TK3.3DR
R3422
1/10GJ3KC
C3422
KK0.047LZB
25
24
23
C011
25EM220LBWA
R3421
1/10GJ3.3KC
C3421
KK2700
LZB
C3418
25PM4.7D
C3413 C3414
EM4.7 16EM100
LBWA LBWA
R003
1/10GJ
1.8KC
TP34
L284
J
<9.0V B5>
IC001
LA4525
AUDIO MUTE
C012
16EM22LBWA
C631
R601
POWER CIRCUIT
7WK1VEA
DY
R518
1/10GJ
18KC
C416
200MM0.27UVB
:250MJ0.27UAP
C508
CJ56CL
R509
6.8K
R512
X
1
KX1P
R513
X
C504
25EM
2200
LBWA
R508
18K
R504
6.8K
R506
560
R507
1/2DJ1
T401
L401
J
C473
HJ0.47
R406
1/2DJ1K
L402
R411
C408
35EM
47LBWA
FO
D612
PHOTO
26V
R630
330
R632
1/10GJ
1KC
R634
47K
R692
180K R694
10K
Q695
2SA
1015Y
R703
1/10GJ820C
C701
KK1200LZB
R701
180
J606
J
RL601
Q693
AE
J616
J
R614
J
R617
C606
250KM
1000VBW
D613
FJ
220P
Q613
2SC3069
R616
1/10G
J10KC
C689
KZ0.1LZF
R618
DJ470
C614
63FJ
0.01
LBZA
R619
1/10GJ
22KC
D683
R
12V
R686 J
POWER REG.
SE130NH
D693
R602
1/2CM
3.3MXU
IC601
CAUTION
D471
5
LOW +B
R726
1/2DJ2.7K
8
6
R716
1/2DJ2.7K
11
KB
J11NA040N
R471
1/2DJ1B
C471
16EM470
LBWA
R497
2SJ4.7
R706
1/2DJ2.7K
Q901
R289 1/10GJ100C
R287 1/10GJ100C
R288 1/10GJ100C
4A 125V
15V
CRT
D429
R
K7Y1
AFC
10
D482
9
R428
15K
TE7
D428
RELAY DRI.
R423
TP7
11
1/10GF3.3KC
D481
C484
EM4.7
LBWA
R421
1/6NF
2.2K

HOLD DOWN CIRCUIT
R482
DJ1B
HEATER
R422
1/6NF
10K
D421
D422
HZ11
HZ11
B2L
B2L
C421
6.3EM220LBWA
KS
GND
C493
100PM
2.2X
R704
82
R713
1/10GJ
820C B-OUT
Q701
C632
250KM
1000
VBW
10
R493
DJ390K
R494
DJ390K
5 9
C482
100
EM22
TP51
<B>
C711
KK1000
LZB
R481
1/2DJ
47B
3
V+B
4
5
R711
180
9V
K701
1000
LZB
R491
DJ1K
1
<G>
TP50
SOCKET
KK
T402
<R>
K7U1
R721
180
G-OUT
Q711
C630
EM1L
BWA
TP35
R714
1/10GJ82C
C613
GNDCONNECTOR
W902
NOTES;
1. RESISTORS SPECIFIED WITH RESISTANCE VALUE ARE "1/6DJ".
2. RESISTORS SPECIFIED WITH TYPE OF RESISTOR, TOLERANCE
AND RESISTANCE VALUE ARE "1/4".
3. ALL CAPACITORS ARE 50WV RATING UNLESS OTHERWISE NOTED.
4. PARTS MARKED WITH
ARE RELATED WITH X-RADIATION.
5. THICK LINES ARE 15WATTS SUPPLY LINE.
6. VIEW OF TR & FET & IC.
LETTER
TOP VIEW
SIDE
N
B
EC
1
7. ISOLATION BORDER LINE.
COLD SIDE
HOT SIDE
E CB
E
BC3
12S
GD
IN CASE
OF TR
IN CASE
OF IC
IN CASE
OF FET
8. LIST OF REPLACEABLE DIODES.

M (7ED00025)
R (7DD00019)
AA (7DD00192)
P (7DD00021)
1SS176, 1SS133, GMA01

1S2076, 1S2473, DS442, 1N4148
1S2076, 1S2473, DS442, 1N4148, 1SS133
1S2076A,1S2471, 1N4148
9. LIST OF REPLACEABLE TRANSISTORS.

AD (7T200183)
AE (7QT00202)
AB (7T200181)
AC (7T200182)
2SC1740S
Q,R,S
Q,R,S
2SA933S
R
Q,R
2SC945A
Q,P
R,Q,P
2SA564A
R
Q,R
2SC1815
Y,GR
O,Y,GR
2SA1015
Y,GR
O,Y,GR
10. "J" : JUMPER WIRE.

"X" : PART NOT USED.
IMPORTANT:
SCHEMATIC PART LOCATION NUMBERS MAY NOT ALWAYS MATCH THE SCHEMATIC SYMBOLS.
THE SCHEMATIC SYMBOLS AND PART DESCRIPTIONS ARE CORRECT AND SHOULD BE USED.
THE PART DESCRIPTIONS WILL BE LISTED UNDER THE LOCATION NUMBER IN THE PARTS LIST.
29
30
31
KD
D614
63FJ
R609
DJ1.5K 6800
LBZA
D629
TP320
SC
F.B.T
C742
2000KZ
1000HE
C721
K7S
D699
TP319
TP36
2
R723
1/10GJ
820C
L602
16
PS601
R727
2SJ
12K
R-OUT
Q721
C625
1000KK
1200CRD
A2
R607
1/2
FJ22
J611
1/10GZ0C
R610
DJ1.2K
J619
J615
1/10GZ0C
AC CORD
F601B
C601
C612
63FJ
3300
LBZA
1/10GZ0C
A1
63FJ0.1LBZA
R724
82
D611
J
W601
250GK
0.22XD
R606
J
R611
47K
F601
4A125V
F601A
R608
1/10GZ0C
J613
1/10GZ0C
LF601
12K
Q701/Q711/Q721
2SC2621CRA
R613
2SJ0.39
11
R695
1/10GJ
22KC
R693
1/10GJ
560KC
Q401
2SC3332R
C406
500KK
1000A
C407
500KK
3900A
HV
K7B
12K
D408
C693
KY1P
X
R717
2SJ
C634
16EM47
LBWA
R404
J
7SJ
6.8VC
L625
Q635
AE
R505
1/2DJ
1.2
2SK2638F82 3
H-OUT
C503
EK2.2AE
R631
DJ6.8K
R405
82
Q402
TT2168LS
21
Q601
COUPLER
B1
7200XK
C506
FK5600
BF
130V
HORIZONTAL DEFLECTION
C411
1500MH
R503
3.9K
R514
J
26V
R629
1/10GJ
1KC
<RGB>
C516
16EM10LBWA
KX3P
L902
R612
1/2FJ10
L623
D625
IN
OUT
R517
18K
D502
TJ1
X
130V
D624
C628
160EM
220XJ
<X-RAY>
D501
R699
DJ10K
C502
35EM
220
2SJ120
KX4P
R511
FOR TEST EQUIPMENT
<POWER FAIL>
KT5P
C511
KX5P FK0.22D
Q681
AE
10
B1
D680
R
R605
DJ560K
D604
C604
500KK1000A
D603
C608
1000KK
1000NH
R603
DJ560K
14
C683
16EM220LBWA
<H-PULSE>
L501
J
KT4P
KT3P
1
KT2P
1
KTP
KT1P
ASSY, PWB, MAIN
L413
HLC
X
<H-DRIVE>
L404
J
C626
16EM
1000
LBWA
R627
1/10GJ
10KC
D601
C603
500KK
1000A
D602
C609
200EM330XG
R604
2SJ2.2
13
C622
35EM
470
LBWA
R628
DJ1.2K
R683
4.7K
L626
J
R408
J
GND
VCC
R485
18K
D487
VERTICAL DEFLECTION
26V
R492
1/6NF33K
D623
Q627
2SB985S
C629
16EM
220LBWA
12
PQ050EA1MXP
100
R884
1/10GJ100C
R276
12K
LA78041
R707
2SJ
26V
T601
TJ3
X
IC681
12V
100
R883
R882
R881
1/10GJ100C
<POWER FAIL>
Q001
AE
250KM
1000VBW
26V
1 2 3
D627
R
<ABL>
ASSY, PWB, SOCKET
5 VOLTS REG
5V
R005
1/10GJ10KC
R006
DJ1.5K
9V-REG.
R487
390
D486
<POWER ON/OFF>
<ALWAYS +5V>
IC501
R013
5.6K
<ACL>
15V
Q005
2SB764E
C003
KK5600LZB
32
SP901
SP902
1.0W 10Z
R472
2SJ8.2
D472
J
J005
1/10GZ0C
Q486
2SD400E-MP
<SIF>
C006
KK0.01LZB
<VERTICAL-OUT>
D001
3
R489
2SJ22
R486
2SJ8.2
C489
16EM220LBWA
TJ5
1/10GJ6.8KC
AUDIO AMP.
C001
EM0.22
LBWA
SPEAKER OUT
C010
25EM220LBWA
C3416
25PM4.7D
C004
KK5600LZB
R004
1/10GJ
1.8KC
KSP
1
C015
16EM330
LBWA
C002
EM0.22LBWA
9V
R272
19
C3424
25PM4.7D
C3417
EM4.7LBWA
C3412
16EM47LBWA
R001
1/10GJ8.2KC
R499
390
18
C3426
10TK10DR
L3401
J
R002
1/10GJ8.2KC
1SJ15
17
27
R3426
1/10GJ3.9KC
C3427
EM1LBWA
VE 26
SAPIN
R3411
1/10GF
62KC
TP301
R488
16
15
R495
1SJ33
TJ6
TRE-R
IC3401
CXA2134QP
AUDIO PROCESSOR
FRAME-GND
17
36
NC 35
SCL
NC
16
AUX2-R
C3411
EM0.47LBWA
R443 4.7K
SURRTC
34
AUX1-R
TVOUT-L
TVOUT-R
AUX2-L
AUX1-L
LSOUT-L
13
C3408
EM0.47LBWA
NC
LSOUT-R
D801
R
R444 18K
25
10
R402
DJ120
37
38
BASS-L
R3407
11
1/10GJ
1MC
12
C3406
C3407
KK0.012 KK5600
LZB
LZB
39
VOLIN-R
<5V B6>
R3406
1/10GJ
100KC
C401
16EM470
LBWA
C509
63GJ 0.47
LBZA
C841
KZ0.1
LZF
C274
16EM10
LBWA
C3404
25PM4.7D
R401
DJ100
C402
63FJ6800
KK0.01
LBZA
LZB
26
L863
J
D831
28
VER
RAMP
AFT
MEMORY
ST24C02B6
27mA +5V
HDR
VCC
C143
KK0.01
LZB
TP132
VER
SEP
27
FRAME-GND
R829
100
OSD
SW
78
TP113
R862
1/10GJ
100C
OSD
FIX GAIN
BRIGHT
R813
1/10GJ
10KC
R814
1/10GJ
10KC
VIF
R833
10K
C829 R831
EM1 1/10
LBWA GJ
100KC
R886
1/10GJ10KC
C801
KK0.01
LZB
C862
KK0.01
LZB
C811
EM1LBWA
<ALWAYS 5V>
BLK,B,G,R
D836
R
D834
R808
1/10GJ
10KC
R816
1/10GJ
330C
C141
KK0.01
LZB
R143
1/10GJ
1KC
29
RF
AGC
77
L801
R400
100
C403
IF
AGC
79
R806
1/10GJ
4.7KC
C405
PM1
LBZA
R409
1/10GJ
5.6KC
TP12
76
KK0.022
LZB
R144
J
TP11
L811
Q831
AJ
C142
L812
R807
1/10GJ
10KC
R3402
1/10GJ220C
31
30
75
C809
CJ100
CL
D843
R
H-GND
DC
REST
R142
1/10GJ
33KC
<RF AGC>
C822
16EM
22
LBWA
CONTRAST
BRIGHT
IF-GND
42
C810
CJ100
CL
C806
6.3EM
470
LBWA
D351
RGB
MATRIX
40
HS
VS
G
40
R3401
1/10GJ220C
41
39
R137
1/10GJ
1KC
CPU
RESET
32
BLACK
STRETCH
74
33
HDR
OUT
DC
VOL
73
R135
1/10GZ0C
COLOR
CLAMP
42
38
R844
1/10GJ560C
PEAKING
CORING
43
37
POWER
FAIL
S SELECT
AV1/AV2
36
72
TP21
R353
10K
R281
1/10GJ10KC
44
L821
35
34
BLK
33
MUTE
32
ACK
31
S-SEL
ABL-IN
30
R849
5.6K
31
PHASE
SHIFTER
AFC1
45
46
29
STATUS
KEY-IN
RC
IN
AVCC
HLF
28
R843
1/10GJ560C
FM
DET
K1011
27
DEMO
34
SW
26
BUS
SCL
25
IIC
SCL
24
BUS
SDA
23
IIC
DSA
22
IC801
QXXAVB927P
AFT
S-CURVE
POWER
RES
VCC
<C022>
FS
RF-AGC
VHOLD
CVIN
CNVSS
XIN
XOUT
VSS
uPROCESSOR
R848
5.6K
DELAY
LINE
C3401
EM0.1LBWA
R449
1/10GF4.7KC
NC
Q135
2 AE
2ND AMP
BPF
R3441
1/10GJ
330KC
R3442
1/10GJ
100C
TRAP
35
47
TOUT-L
STIN
NOISETC
SAPOUT
AFC2
48
1
SUOUT
HDR
C/D
C3436
25PM4.7D
NC
FBP
VCC
1/256
SYNC
SEP
C3441
EM4.7
LBWA
37
C3431
KK4700
LZB
R441
1K
36
LIM
AMP
71
C441
KK0.01LZB
C3439
25PM
4.7D
38
ACC
KILLER
R3443
1/10GJ
330KC
R3444
1/10GJ
100C
R1 IN
R442
1/10GJ10KC
<P-FAIL>
R842
1/10GJ560C
39
C3442
EM4.7
LBWA
C3433 C3434
KK4700 KK0.022
LZB
LZB
C3432
EM0.1LBWA
<X-RAY>
H-GND
HDR
VCO
1ST AMP
BPF
R847
5.6K
C427
KK0.01
LZB
<12V>
10
CW
KIL
TINT
70
C835
KK0.01
LZB
11
APC1
L1 IN
40
BPF
BPF
D1002
FRONT A/V JACK
SPLL
69
Q1071
AC
R426
1/10GJ680C
X-RAY
VIDEO
SW
R1002
1/10GJ75C
V1 IN
41
<H-PULSE>
12
C137
CJ10CL
BLK
42
43
FRAME-GND
SW
R846
1K
44
<H-DRIVE>
13
45
<HS>
14
46
<VS>
15
CLMP
47
16
NC
48
17
49
18
68
C134
KK1000LZB
19
50
VCO
VIDEO
DET
IF-VCC
60mA
20
51
VIDEO
AMP
IF-GND
21
52
SAPTC
CLMP
67
C133
R133
1/10GJ KK0.01
LZB
3KC
R835
1/10GJ2.7KC
R858
1/10GJ
22KC
53
A2C
PLL
L851
54
C136
1/10GZ
0C
R851
1/10GJ
1KC
55
65
EM0.47LBWA
C856
EM1LBWA
C858
KK1000
LZB
56
TOUT-R
NC
FRAME-GND
C854
CJ82CL
R852
1/10GJ39KC
1
57
C151
66
C857
CJ220CL
58
BASS-R
59
R1084
1/10GJ10KC
GND
60
R2 IN
R3445
1/10GJ
330KC
R3446
1/10GJ
100C
R1083
1/10GJ27KC
NC
61
R3447
1/10GJ
330KC
C3447
EM4.7LBWA
VOLIN-L
TRE-L
NC
62
REAR A/V JACK
L2 IN
C1002
16EM10LBWA
<V-OUT>
1K
R151
1/10GJ
330C
C853
EM0.1LBWA
63
C3448
EM4.7LBWA
R853
1/10GJ
1MC
R1909
64
C251
1/10GZ
0C
R167
1/10GJ
180C
R854
1/10GJ2.2KC
C1071
KK0.01LZB
2VP-P
D1901 SW1906 SW1905 SW1904 SW1903 SW1902 SW1901
X801
C153
EM0.47
LBWA
POWER
R1053
10K
C256
EM1
LBWA
19mA +8V
VOL.+
BLK
VOL.-
R1071
390
R321
1/10GJ
10KC
R3448
1/10GJ
100C
R1054
27K
C252
63FK0.047LBZB
X251
C221
PM1LBZA
CH +
<SDA>
CH -
PRESET
R212
1/10
GJ
680KC
V/C/VERT
GND
C253
EM0.47LBWA
R251
1/10GJ
22KC
R209
1/10GJ
100C
C258
16EM47
LBWA
VIF/SIF/Y/C/DEFLECTION
1
2
1
2
R166
1/10GJ
390C
1
2
1
2
L1901
C212
EM2.2
LBWA
1VP-P
T151
L14B1840N
2VP-P
LA76834NMP
<RF AGC>
R252
22K
C211
PM1
LBZA
R163
1/10GJ
120C
<IF>
1
L164
IC101
D1001
C SW
C257
KK0.01
LZB
L256
J
V2 IN
R1910
1K
R1901
1/10GJ10KC
5VB6
1VP-P
X161
C1902
16EM10LBWA
Q202
AC
R164
1/10GJ1KC
R1073
100
Q208
AC
<SCL>
R1902
1/10GJ1KC
R1903
1/10GJ1.8KC
R1904
1/10GJ2.2KC
R1905
1/10GJ3.9KC
R1907
1/10GJ12KC
R1906
1/10GJ5.6KC
C106
EM2.2LBWA
V/C/VERT
VCC
A1901
U20B40500
VIDEO SW
H
C1001
16EM10LBWA
SW
Y SW
IREF
J201
1/10
GZ0C
COMPIN
VGR
AV
R201
470
TP16
K1002
R1001
1/10GJ75C
TC4053BP
<130V>
D1902
15
VCC
V1 IN
16
B1
REMOTE SENSOR
IC1081
D101
V2 IN
C103
KK
0.01
LZB
L901
D. COIL

DS20930 1

Uploaded by

Copyright:

Available Formats

DS20930 1

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DS20930 1

Uploaded by

Copyright:

Available Formats

AS

Please add this notice to the Service Manual listed below.

Effective from : Chassis No.

Destination: U.S.A. / CANADA

REF : No. SM780088-06

The reason for change.

DS20930, G8TDM, PRODUCT CODE 111367880

REFERENCE No. SM780088-07

Please add this notice to the Service Manual listed below.

Effective from : Chassis No.

Power Rating . . . . . . . . . . . . . . . . . . . . . 120V, 60Hz

DS20930, G8TCM, PRODUCT CODE 111367880

REFERENCE No. SM780088-06

READING SHOULD NOT EXCEED 750 mV.

3. When replacing a chassis in the cabinet, always be certain

ANTENNA COLD CHECK

LEAKAGE CURRENT CHECK

Good earth ground

To be touched to all of exposed metal parts.

HIGH VOLTAGE HOLD-DOWN TEST

PRODUCT SAFETY NOTICE

ON-SCREEN SERVICE MENU SYSTEM

1. Enter the Service Menu:

Use the + or key or number keys to adjust the data.

Figure 1. Service Menu Display

(b7) (b6) (b5) (b4) (b3) (b2) (b1) (b0)

IC802 (EEPROM) REPLACEMENT

INITIAL BUS DATA SETUP

Disconnect the AC power cord (AC 120V line).

SERVICE ADJUSTMENTS (Cont.)

Table 1. ON-SCREEN SERVICE MENU

Sub Contrast (4~0)

Sub Color (5~0)

Sub Tint (4~0)

Sub Bright (5~0)

Sub Sharpness (4~0)

AFC(6) Horizontal Frequency (5~0)

Horizontal Phase (4~0)

V Sync Sep (7) V Kill (6) V DC (5~0)

H Blanking L (6~5) V. Linearity (4~0)

H Blanking R (6~5 V Shift (3~0)

Vertical S Correction (4~0)

V Test (7~6) V Compression (5~3)Count Down Mode (0)

Red Bias (7~0)

Green Bias (7~0)

Blue Bias (7~0)

Red Drive (6~0)

Green Drive (3~0)

Blue Drive (6~0)

Sub Bias (6~0)

On Screen Display Contrast (1~0)

Coring Gain (7~6)

S Trap Test (6~4) Y/C Filter Mode (2~0)

Auto Flesh (7) C Bypass (5)

Color Killer (2~0)

R-Y/B-Y Angle (3~0)

Cb DC Offset (7~4) Cr DC Offset (3~0)

G-Y Angle (3)

IF AGC (7) S Trap SW (6) RF AGC (5~0)