Scanspeak Full V10

Model
Imp Fs Hz 4 4 4 4 4 4 4 4 4 4 4 4 4 8 4 8 4 8 4 8 4 4 4 4 4 8 4 4 4 8 8 4 8 4 8 8 8 4 8 4 4 600 700 425 600 625 420 490 500 500 500 520 520 64 66 34 35 30 31 32 33 520 520 520 520 520 500 75 35 39.5 30 30 33 28 20.5 21 23 19 18 19 20.5 20.5
Qts
Vas Ltrs
Power
dB Xmax 2.83V/m mm P 88.4 89.2 89.6 86.9 87.4 87.4 90.7 91.6 91.6 91.6 90.4 90.4 90 87.2 85.9 83.4 87.2 85.4 88.1 85.5 94.5 94.5 94.5 94.5 94.5 91 89 90 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 3.5 3.5 9 9 9 9 9 9 0.2 0.2 0.2 0.2 0.2 0.4 3.0 3.0 6.5 6.5 6.5 6.5 6.5 9.0 9.0 9.0 9.0 9.0 9.0 13 13
Box Liter
F3 Hz
Sealed/Vented
Price Each $121.85 $124.55 $130.90 $152.40 $157.30 $164.65 $508.20 $212.95 $232.65 $232.65 $271.35 $271.35
Illuminator Series Tweeters

D2004/6020-00: " dome tweeter, 55.5mm , metal grill, chamber D3004/6020-00: 1" dome tweeter, 62mm , metal grill, chamber D3004/6020-10: 1" dome tweeter, 62nn , metal grill, deep chamber R2004/6020-00: " ring radiator, 55.5mm , metal grill, chamber R3004/6020-00: 1" ring radiator, 62mm , metal grill, chamber R3004/6020-10: 1" ring radiator, 62mm , metal grill, deep chamber D3004/6640-00: 1" Beryllium dome, AirCirc neo. magnet, Black D3004/6600-00: 1" dome, AirCirc, neodymium magnet D3004/6620-00: 1" dome, AirCirc, neo magnet, rubber front, Black D3004/6620-01: 1" dome, AirCirc, neo magnet, rubber front, Silver R3004/6620-00: 1" ring radiator, AirCirc, neo, rubber front, Black R3004/6620-01: 1" ring radiator, AirCirc, neo, rubber front, Silver 12MU/4731T: 4" midrange, paper cone, neo magnet, underhung VC 12MU/8731T: 4" midrange, paper cone, neo magnet, underhung VC 15WU/4741T: 5.25" woofer, paper cone, neo magnet, underhung VC 15WU/8741T: 5.25" woofer, paper cone, neo magnet, underhung VC 18WU/4741T: 6.5" woofer, paper cone, neo magnet, underhung VC 18WU/8741T: 6.5" woofer, paper cone, neo magnet, underhung VC 18WU/4747T: 6.5" woofer, aluminum cone, neo magnet, underhung 18WU/8747T: 6.5" woofer, aluminum cone, neo magnet, underhung R2904/7000-00: Premium Ring Radiator - Silver R2904/7000-05: Premium Ring Radiator - Black w/silver plug R2904/7000-09: Premium Ring Radiator - Black D2904/7100-02: Premium Wide Surround Tweeter - Silver D2904/7100-03: Premium Wide Surround Tweeter - Black D2905/9900: 1 textile dome, SD-2, LCD, NRC, CDD 12M/4631G: 4.5 slit paper cone, neodymium magnet, R3 15M/4531K: 5" slit paper cone midrange, Glass former 15W/4531G: 5 slit paper cone, NRCS, SD-1, R3, Glass former 15W/8530K-00: 5 paper cone, NRCS, SD-1, R3, Glass former 15W/8530K-01: 5 paper cone, NRCS, SD-1, R3, Glass former 18W/4531G: 7" slit paper cone, SD-1, R3, Glass former 18W/8531G: 7 slit paper cone, SD-1, R3, Glass former 22W/4851T: 8" hard paper cone, SD-1, Titanium former 22W/8851T: 8" hard paper cone, SD-1, Titanium former 22W/8857T: 8" Black Aluminum cone, SD-1, Titanium former 26W/8861T: 10" hard paper cone, SD-1, Titanium former 26W/4867T: 10" Black Aluminum cone, SD-1, Titanium former 26W/8867T: 10" Black Aluminum cone, SD-1, Titanium former 23W/4557T-00: 10" Aluminum Cone, SD-1, Titanium former, Silver 23W/0-00-00: 10" Aluminum Cone Passive Radiator, Silver 23W/4557T-02: 10" Aluminum Cone, SD-1, Titanium former, Black 23W/0-00-02: 10" Aluminum Cone Passive Radiator, Black D2008/8512: " dome, chamber D2010/8513: dome, chamber, foam on faceplate, ff D2905/9300: 1 textile dome, chamber, FF D2905/9500: 1 textile dome, NRC, FF D2905/9700: 1 textile dome, SD-2, LCD, NRC D2904/9800: 1 aluminum dome, diffuser, SD-2, NRC 60 50 50 60 50 50 160@2.5k 160@2.5k 160@2.5k 160@2.5k 160@2.5k 160@2.5k 0.24 0.29 0.23 0.26 0.29 0.33 0.28 0.31 5.4 5.9 20.1 20.1 49.9 49 48.7 49.2 80 80 80 80 80 80 80 80 160@2.5k 160@2.5k 160@2.5k 160@2.5k 160@2.5k 225@2.8k 0.33 0.22 0.32 0.27 0.35 0.35 0.36 0.22 0.25 0.30 0.31 0.30 0.29 2.4 24 16 28 28 42 59 127 127 89 234 223 179 60 60 60 70 60 170 170 170 170 170 170 225 225 40@75
Illuminator Series Midranges

0.1 / 0.1 0.1 / 0.1 0.15 / 0.25 0.15 / 0.25 0.25 / 0.5 0.35 / 0.6 0.2 / 0.45 0.25 / 0.6 190 / 115 190 / 115 115 / 60 105 / 58 80 / 55 70 / 50 97 / 59 84 / 55 $298.70 $298.70 $342.15 $342.15 $341.40 $341.40 $325.50 $325.50 $371.15 $371.15 $371.15 $312.30 $312.30 $262.30 0.7 / 1.0 3.0 / 5.0 4/6 5.1 / 7.4 9.5 / 15 14 / 23 21 / 36 10 / 28 18 / 34 14 / 35 55 / 90 46 / 71 36 / 57 28 / 59 28 / 59 160 / 100 $314.20 100 / 70 88 / 58 77 / 55 60 / 40 65 / 41 54 / 35 70 / 40 60 / 38 60 / 38 40 / 28 43 / 29 46 / 31 33 / 27 33 / 27 $223.80 $235.70 $213.90 $223.70 $237.05 $237.05 $374.40 $374.40 $348.95 $416.70 $381.30 $381.30 $434.20 $166.90 $434.20 $166.90 $77.45 $83.85 $122.55 $140.15 $180.25 $214.00
Illuminator Series Woofers
Revelator Series Tweeters
Revelator Series Midranges
Revelator Series Mid/Bass & Woofers

87 85.5 84.5 90 87 89 88 89 88.5 89 87 83 83
0.44 43.5 0.44 43.5
Fs 10.5 Hz, Sd 232 cm2, Mms 400g, Vas 43.5 Ltrs, Qms 11.5, Excursion +20mm Fs 10.5 Hz, Sd 232 cm2, Mms 400g, Vas 43.5 Ltrs, Qms 11.5, Excursion +20mm
Classic Series Tweeters

8 8 8 8 8 4 800 800 650 550 500 500 150#4k 150@4k 150@2.5k 150@2.5k 225@2.8k 160@2.8k 90 90 90 90 89.5 90 0.7 0.7 0.4 0.4 0.4 0.1
Model
Imp Fs Hz 8 8 8 8 8 8 8 6 6 4 8 4 4 8 4 8 4 4 8 4 8 4 8 4 8 4 8 4 4 450 26 30 28 28 20 20 1100 650 475 700 550 630 300 90 90 100 50 52 43 45 39 40 30 30 23 23 20 21
Qts
Vas Ltrs
Power
dB Xmax 2.83V/m mm P 89 86.5 89 88 87.5 87 88 91.4 91 94.1 91.3 90.8 91.9 92 89.8 86.6 92.4 88.8 85.8 89.7 86.9 90.8 88 92.4 88.8 90.5 89 89 89 0.4 5.0 6.5 6.5 6.5 5.5 6.5 0.5 0.5 0.3 0.5 0.2 0.2 0.5 2.6 2.6 1.5 1.5 1.5 4.3 4.2 4.3 4.2 5.7 5.8 6 6 12.5 12.5
Box Liter
F3 Hz
Sealed/Vented
Price Each $192.00
Classic Series Mid/Tweeter

D3806/8200: 1.5" textile dome mid/tweeter 18W/8535: 7 carbon paper cone, SD-1, R3 18W/8542: 7" paper cone, SD motor, foam surround 18W/8545: 7 carbon paper cone, SD-1, R3 18W/8545K: 7 carbon paper cone, SD-1, R3, Glass former 21W/8555:8" paper/carbon cone woofer, SD-1 26W/8565: 10" paper/carbon cone woofer, SD-1 D2606/9200: 1" textile dome tweeter D2606/9220: 1" textile dome tweeter with chamber, vented pole piece D2604/8330: 1" textile dome, large roll surround D2608/9130: 1" textile dome, double magnet, high efficiency R2604/8320: 1" textile ring tweeter, wave guide, chamber R2604/8330: 1" textile ring dome tweeter, wave guide, double magnet D7608/9200-10: 3" textile dome midrange, needs chamber on back 10F/4424G: 4" fiberglass cone midrange, neodymium magnet 10F/8424G: 4" fiberglass cone midrange, neodymium magnet 15M/4624G: 5" fiberglass cone midrange, phase plug, 24mm VC 12W/4524G: 5" fiberglass cone woofer, 24mm VC 12W/8524G: 5" fiberglass cone woofer, 24mm VC 15W/4434G: 5" fiberglass cone woofer, shorting ring, 34mm VC 15W/8434G: 5" fiberglass cone woofer, shorting ring, 34mm VC 18W/4434G: 6" fiberglass cone woofer, shorting ring, 34mm VC 18W/8434G: 6" fiberglass cone woofer, shorting ring, 34mm VC 22W/4534G: 8" fiberglass cone woofer, shorting ring, 34mm VC 22W/8534G: 8" fiberglass cone woofer, shorting ring, 34mm VC 26W/4534G: 10" fiberglass cone woofer, shorting ring 34mm VC 26W/8534G: 10" fiberglass cone woofer, shorting ring 34mm VC 26W/4558T: 10" Aluminum cone subwoofer, shorting ring 26W/0-00: 10" Aluminum cone passive radiator 400 gram 30W/4558T: 12" Aluminum cone subwoofer, shorting ring 30W/0-00: 12" Aluminum cone passive radiator 425 gram 100@1.5k 0.38 0.22 0.27 0.28 0.31 0.41 72 49 48 48 134 225 70 70 100 100 100 100 100@2.5k 100@2k 100@2k 100@2k 100@2k 100@2k 80@500 0.30 2.06 0.37 0.43 0.27 0.32 2.1 3.6 8.2 8.2 15RMS 15RMS 75RMS 40RMS 40 RMS 60RMS 60RMS 60RMS 60RMS 70RMS 70RMS 70RMS 70RMS 150RMS 150RMS
Classic Series Woofers

30 / 46 4 / 14 8 / 15 9 / 19 20 / 35 60 / 48 / 33 107 / 58 75 / 46 70 / 42 55 / 36 40 / $182.95 $194.40 $174.40 $170.15 $247.75 $259.20 $36.65 $51.90 $53.90 $81.40 $54.45 $63.80 1/1.5 / 1.5 / 2.5 / 2/3 2 / 4.5 3 / 3.5 3/5 5 / 12 6 / 15 18 / 45 18 / 45 35 / 85 45 / 100 - / 56 - / 90 500 / 270 / 210 / 205 / 145 / 80 135 / 75 160 / 80 145 / 75 100 / 60 90 / 55 75 / 40 75 / 40 55 / 32 50 / 31 - / 28 - / 26 $103.10 $100.95 $100.95 $77.85 $64.90 $64.90 $70.70 $70.70 $73.75 $73.75 $88.20 $88.20 $106.40 $106.40 $247.40 $132.75 $270.30 $158.15 $432.00 $450.00 $14.70 $15.00 88 88 91 4 4 4 3/6 8 / 15 20 / 45 145 / 80 90 / 55 70 / 40 $76.20 $76.90 $85.55
Discovery Series Dome Tweeters
Discovery Series Midranges
Discovery Series Woofers
0.21 12.9 0.25 12.9 0.29 28.5 0.34 28.5 0.34 0.36 0.40 0.28 0.34 95 156 150 104 147 0.39 94.2
Discovery Series Subwoofers and Passive Radiators

Use with 26W/4558T in 1 cubic foot for F3 of 35Hz use amp with 25Hz boost Use with 30W/4558T in 2 cubic feet for F3 of 30Hz
Discovery Series Autosound Component Systems

820012: 5" 2-way Component System, 2x 5" fiberglass cone woofers, 2x 19mm ring dome tweeters with flush/wedge mounts, 2x 2500Hz crossovers 820013: 6" 2-way Component System, 2x 6" fiberglass cone woofers, 2x 19mm ring dome tweeters with flush/wedge mounts, 2x 3000Hz crossovers 290001: Scan speak flow resistive aperiodic vent, used to lower the box Q of a sealed box. It makes the driver behave as if the box is 25% larger. Each 127001: Scan speaker grill for Classic 18W woofers, does not fit the Revelator or Illuminator woofers. Each
Classic Vifa Drivers Built by Scan-Speak

P13WH00-08: 5" mineral filled poly cone, 140mm cast frame P17WJ00-08: 6.5" mineral filled poly cone, 170mm cast frame P21WO20-08: 8" mineral filled poly cone, 215mm cast frame 8 8 8 60 37 28 0.33 0.33 10 113 40 40 80 0.35 34.7
Founded in 1970, Scan-Speak still resides at our original address in Videbaek, Denmark. Located in the heart of the Jutland peninsula, our acoustic engineers adhere to our legendary policy of "Never compromise". We never compromise on our product quality, sound quality or pursuit of perfection in a given application. We set the loudspeaker industry's gold standard for audiophiles, and are constantly viewed as a market benchmark by other high-end speaker manufacturers. For close to 40 years, Scan-Speak has been on a quest to create transducers that reveal the finest details in recordings, concealing nothing from the listener. This quest has resulted in several revolutionary inventions, where distortion in the magnet systems and the moving parts of the speaker is minimized. Our philosophy is simple: the emitted sound must be dynamic, giving a transient response and providing tonal balance.
Illuminator D2004/6020-00
Illuminator D3004/6020-00 4
The face plates are die cast in aluminum for a beautiful look with maximum mechanical stability. D3004/602000 is optimized to offer small package sizes that can fit into tight spaces such as compact cabinets and automotive trim pieces. The back chamber is die cast in aluminum and designed with a contoured shape that functions as a heat sink in high power applications. This tweeter is a good choice for home or autosound systems. Driver Highlights: 1 soft dome, compact size, ring neodymium magnet, aluminum faceplate and house, protective grill.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 89.2dB 700 Hz 3.0 ohm 0.02 mH 50W 7 cm2 26 mm 2.1 mm 2.5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Outside diameter Cutout diameter Flange thickness Depth Screw Circle 0.2 / 1.6 mm 1.7 Tm 0.35 g 61.9 mm 48.5 mm 5 mm 21.5 mm 53.9 mm
The face plates are die cast in aluminum for a beautiful look with maximum mechanical stability. D2004/602000 is optimized to offer small package sizes that can fit into tight spaces such as compact cabinets and automotive trim pieces. The back chamber is die cast in aluminum and designed with a contoured shape that functions as a heat sink in high power applications. Driver Highlights: 3/4 soft dome, compact size, ring neodymium magnet, aluminum faceplate and house, protective grill.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 88.4dB 600 Hz 3.4 ohm 0.02 mH 50W 4.5 cm2 19 mm 1.8 mm 2.5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Outside diameter Cutout diameter Flange thickness Depth Screw Circle 0.4 / 01.8mm 1.3 Tm 0.22 g 55.5 mm 42.1 mm 5 mm 29.3 mm 47.6 mm
The face plates are die cast in aluminum for a beautiful look with maximum mechanical stability. D3004/602010 is optimized to offer small package sizes that can fit into tight spaces such as compact cabinets and automotive trim pieces. The back chamber is die cast in aluminum and designed with a contoured shape that functions as a heat sink in high power applications. Driver Highlights: 1 soft dome, compact size, ring neodymium magnet, aluminum faceplate and house, protective grill, large chamber.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 89.6dB 425 Hz 3.0 ohm 0.02 mH 50W 7 cm2 26 mm 2.1 mm 2.5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Outside diameter Cutout diameter Flange thickness Depth Screw Circle 0.2 / 1.6 mm 1.7 Tm 0.35 g 61.9 mm 48.5 mm 5 mm 55.4 mm 53.9 mm
Illuminator R2004/6020-00 4
The face plates are die cast in aluminum for a beautiful look with maximum mechanical stability. R2004/602000 is optimized to offer small package sizes that can fit into tight spaces such as compact cabinets and automotive trim pieces. The back chamber is die cast in aluminum and designed with a contoured shape that functions as a heat sink in high power applications. Driver Highlights: soft ring dome, compact size, ring neodymium magnet, aluminum faceplate and house, protective grill, chamber.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 86dB 675 Hz 2.8 ohm 0.02 mH 50W 3.8 cm2 19 mm 1.8 mm 2.5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Outside diameter Cutout diameter Flange thickness Depth Screw Circle 0.4 / 1.6 mm 1.3 Tm 0.22 g 55.5 mm 42.1 mm 5 mm 29.3 mm 47.6 mm
The face plates are die cast in aluminum for a beautiful look with maximum mechanical stability. R3004/602000 is optimized to offer small package sizes that can fit into tight spaces such as compact cabinets and automotive trim pieces. The back chamber is die cast in aluminium and designed with a contoured shape that functions as a heat sink in high power applications. Driver Highlights: 1 soft ring dome, compact size, ring neodymium magnet, aluminium faceplate and house, protective grill, chamber.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 87.4dB 625 Hz 3.0 ohm 0.02 mH 50W 5.6 cm2 26 mm 2.1 mm 2.5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Outside diameter Cutout diameter Flange thickness Depth Screw Circle 0.2 / 1.6 mm 1.7 Tm 0.35 g 61.9 mm 48.5 mm 5 mm 21.5 mm 53.9 mm
The face plates are die cast in aluminum for a beautiful look with maximum mechanical stability. D3004/602010 is optimized to offer small package sizes that can fit into tight spaces such as compact cabinets and automotive trim pieces. The back chamber is die cast in aluminium and designed with a contoured shape that functions as a heat sink in high power applications. Driver Highlights: 1 soft ring dome, compact size, ring neodymium magnet, aluminium faceplate and house, protective grill, large chamber.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 87.4dB 420 Hz 3.0 ohm 0.02 mH 50W 5.6 cm2 26 mm 2.1 mm 2.5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Outside diameter Cutout diameter Flange thickness Depth Screw Circle 0.2 / 1.6 mm 1.7 Tm 0.35 g 61.9 mm 48.5 mm 5 mm 55.4 mm 53.9 mm
This tweeter features a 99% pure Beryllium dome diaphragm. The large roll surround and Beryllium dome diaphragm provide a flat frequency response to above 40KHz with outstanding off-axis dispersion and a silky-smooth sound. AirCir magnet system with neodymium magnets and unique air flow. Driver Highlights:- 1" Beryllium Diaphragm (99% pure Beryllium)AirCirc Magnet System with 6 Neodymium Magnet slugs- Die cast rubber painted aluminium faceplate for maximum mechanical stability and beautiful look- Protective grill.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 91.5dB 500 Hz 3.0 ohm 0.03 mH 160W@2.5K 7 cm2 26 mm 2.1 mm 2.5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Outside diameter Cutout diameter Flange thickness Depth Screw Circle 0.2 / 1.6 mm 2.3 Tm 0.35 g 104 mm 77 mm 5 mm 23 mm 90 mm
The new D3004/660000 builds on the experience of the one-inch R29 ring radiator, resulting in low resonance frequency, but further provides the extended dispersion characteristics of a -inch dome. Tymphanys unique AirCirc Magnet System named for the way it optimizes air flow within the chamber rearranges the traditional magnet structure from a single magnet to an open magnetic circuit comprised of six separate neodymium slugs. This, in combination with the chamber, results in the elimination of the reflections and resonances that compromise the performance of traditional motors.
Tymphanys unique AirCirc Magnet System - named for the way it optimizes air flow within the chamber rearranges the traditional magnet structure from a single magnet to an open magnetic circuit comprised of six separate neodymium slugs. This, in combination with the chamber, results in the elimination of the reflections and resonances that compromise the performance of traditional motors. The D3004 gives engineers improved control over critical midrange performance, for superb vocal rendition and excellent imaging at all listening locations. Driver Highlights: 1" soft dome, AirCirc Magnet System, Rubber painted aluminum faceplate, Black
Tymphanys unique AirCirc Magnet System - named for the way it optimizes air flow within the chamber rearranges the traditional magnet structure from a single magnet to an open magnetic circuit comprised of six separate neodymium slugs. This, in combination with the chamber, results in the elimination of the reflections and resonances that compromise the performance of traditional motors. The D3004 gives engineers improved control over critical midrange performance, for superb vocal rendition and excellent imaging at all listening locations. Driver Highlights: 1" soft dome, AirCirc Magnet System, Rubber painted aluminum faceplate, Silver
The ring radiator tweeter uses a phase plug. The dome is attached to the phase plug, so the radiating area is now concentrated around the voice coil. This offers more control and reduces distortion and loss that occur at the center of the dome on dome tweeters. Tymphanys unique AirCirc Magnet System - named for the way it optimizes air flow within the chamber rearranges the traditional magnet structure from a single magnet to an open magnetic circuit comprised of six separate neodymium slugs. This, in combination with the chamber, results in the elimination of the reflections and resonances that compromise the performance. Black
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 90.4dB 520 Hz 3.0 ohm 0.03 mH 160W@2.5K 5.6 cm2 26 mm 2.1 mm 2.5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Outside diameter Cutout diameter Flange thickness Depth Screw Circle 0.2 / 1.6 mm 2.3 Tm 0.3 g 104 mm 77 mm 5 mm 23 mm 90 mm
The ring radiator tweeter uses a phase plug. The dome is attached to the phase plug, so the radiating area is now concentrated around the voice coil. This offers more control and reduces distortion and loss that occur at the center of the dome on dome tweeters. Tymphanys unique AirCirc Magnet System - named for the way it optimizes air flow within the chamber rearranges the traditional magnet structure from a single magnet to an open magnetic circuit comprised of six separate neodymium slugs. This, in combination with the chamber, results in the elimination of the reflections and resonances that compromise the performance. Silver
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 90.4dB 520 Hz 3.0 ohm 0.03 mH 160W@2.5K 5.6 cm2 26 mm 2.1 mm 2.5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Outside diameter Cutout diameter Flange thickness Depth Screw Circle 0.2 / 1.6 mm 2.3 Tm 0.3 g 104 mm 77 mm 5 mm 23 mm 90 mm
Illuminator 4.5" 12MU/4731T-00 4

The Illuminator midrange is based on compact underhung motor systems with large neodymium ring magnets. The patent pending motor offers a very long linear excursion together with a very high force factor. The top plate is shaped to guide the backside airflow around the motor and with the very open cast aluminum chassis design the driver is virtually free from compression. The cone and dust cap is made in one piece full cone technology. Frame diameter 120mm, cutout hole size 101mm, depth 66mm.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 90 dB 64 Hz 3.1 ohm 0.11 mH 80W 58 cm2 32 mm 6.0 mm 13.0 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 3.5 & 10mm 5.14 Tm 5.4 g 0.8 kg 5.4 ltrs 3.64 0.26 0.24
Illuminator 4.5" 12MU/8731T-00 8

The Illuminator midrange is based on compact underhung motor systems with large neodymium ring magnets. The patent pending motor offers a very long linear excursion together with a very high force factor. The top plate is shaped to guide the backside airflow around the motor and with the very open cast aluminum chassis design the driver is virtually free from compression. The cone and dust cap is made in one piece full cone technology. Frame diameter 120mm, cutout hole size 101mm, depth 66mm.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 87.2 dB 66 Hz 5.9 ohm 0.13 mH 80W 58 cm2 32 mm 6.2 mm 13.0 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 3.4 & 11mm 6.1 Tm 4.7 g 0.8 kg 5.9 ltrs 3.63 0.31 0.29
Illuminator 5.25" 15WU/4741T-00 4

The Illuminator woofers are based on compact under-hung motor systems with large neodymium ring magnets. The patent pending motor offers a very long linear excursion together with a very high force factor. The top plate is shaped to guide the backside airflow around the motor and with the very open cast aluminum chassis design the driver is virtually free from compression. F3 of 60Hz in 0.25 cubic foot vented . Frame diameter 149mm, cutout hole diameter 123mm, depth 91mm.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter VC height Air gap 85.9dB 34 Hz 3.2 ohm 0.5 mH 80W 92 cm2 42 mm 8 mm 20 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 9 / 12 mm 6 Tm 13 g 1.6 kg 20.1 ltrs 3.47 0.25 0.23

TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter VC height Air gap 83.4dB 35 Hz 5.9 ohm 0.41 mH 80W 92 cm2 42 mm 8 mm 20 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 9 / 12 mm 6 Tm 12.3 g 1.6 kg 20.1 ltrs 3.37 0.28 0.26

TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter VC height Air gap 87.2dB 30 Hz 3.2 ohm 0.5 mH 80W 154 cm2 42 mm 8 mm 20 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 9 / 16 mm 6 Tm 18.9 g 1.7 kg 49.4 ltrs 3.56 0.32 0.29

TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter VC height Air gap 85.4dB 31 Hz 5.9 ohm 0.41 mH 80W 154 cm2 42 mm 8 mm 20 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 9 / 16 mm 7.5 Tm 18 g 1.7 kg 48.6 ltrs 3.51 0.37 0.33

The Illuminator woofers are based on compact under-hung motor systems with large neodymium ring magnets. The patent pending motor offers a very long linear excursion together with a very high force factor. The top plate is shaped to guide the backside airflow around the motor and with the very open cast aluminum chassis design the driver is virtually free from compression. Black anodized aluminum cone. Frame diameter 184mm, cutout hole diameter 160mm, depth 98mm.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter VC height Air gap 88.1dB 32 Hz 3.2 ohm 0.39 mH 80W 154 cm2 42 mm 8 mm 20 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 9 / 16 mm 6 Tm 17 g 1.7 kg 48.7 ltrs 3.42 0.30 0.28

The Illuminator woofers are based on compact under-hung motor systems with large neodymium ring magnets. The patent pending motor offers a very long linear excursion together with a very high force factor. The top plate is shaped to guide the backside airflow around the motor and with the very open cast aluminum chassis design the driver is virtually free from compression. Black anodized aluminum cone. Frame diameter 184mm, cutout hole diameter 160mm, depth 98mm.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter VC height Air gap 85.5dB 33 Hz 5.9 ohm 0.41 mH 80W 154 cm2 42 mm 8 mm 20 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 9 / 16 mm 7.5 Tm 16 g 1.7 kg 49.2 ltrs 3.31 0.35 0.31
R2904/7000 4
The R2904/7000 tweeter is the new flagship tweeter in the Scan-speak line. This tweeter incorporates many innovative design concepts. The first notable difference is the use of a phase plug. The dome is attached to the phase plug, so the radiating area is now concentrated around the voice coil. This offers more control and reduces distortion and loss that occur at the center of the dome on dome tweeters. The phase plug also acts as a wave guide, reducing high frequency cancellations. A specially designed venting system uses a needle to cut down on turbulence in the air cavity. Better dynamics are achieved by not using ferrofluid, voice coil cooling is performed by the venting system and conduction through copper rings. The new SD-2 neodymium magnet system improves transient response.
TECHNICAL DATA: Sensitivity 2.83V/1M 94.5dB Free air resonance Fs 520 Hz DC resistance 3.0 ohm V.C. inductance 0.01 mH Power 12dB@Hz 150W@2.7K Effective cone area V.C. diameter Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight 5.6 cm2 28 mm 0.2 / 1.6mm 2.8 Tm 0.3 g 0.42 kg
D2904/7100 4
The D2904/7100 tweeter is a 1" soft dome with wide surround, using the same chambering as the Ring Radiator. The carefully designed dome and surround result in a linear response and an exceptionally good off axis response. Note the smooth roll off on the low end, making this tweeter a good choice for simple slopes A specially designed venting system uses a needle to cut down on turbulence in the air cavity. Better dynamics are achieved by not using ferrofluid, voice coil cooling is performed by the venting system and conduction through copper rings. The new SD-2 neodymium magnet system improves transient response.
TECHNICAL DATA: Sensitivity 2.83V/1M 94.4dB Free air resonance Fs 520 Hz DC resistance 3.0 ohm V.C. inductance 0.01 mH Power 12dB@Hz 150W@2.5K Effective cone area V.C. diameter Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight 7 cm2 28 mm 0.2 / 1.6mm 2.8 Tm 0.35 g 0.42 kg
D2905/9900
Revelator Dome Tweeter
The D2905/9900 is our state of the art tweeter. This revelation is a 1" textile dome tweeter that will reach new borders within high-end loudspeaker drive units. The new magnet system with SD caps and rings that eliminate the electrical phase shift. The new chamber design reduces air noises and compression. The 130mm machined aluminum front plate has more controlled directivity (down to 2Khz). The textile dome is hand coated and a special device is placed behind it to reduce dynamic compression.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter 91dB 500 Hz 4.7 0.01 mH 225W@2.8kHz 8.5 cm2 28 mm V.C. height Air gap height Lin. & max. excursion Air gap flux density BL Moving mass incl. air Net weight 3.3mm 2.5mm 0.4/ 1.5 mm 3.5 Tm 0.45 g 0.8 kg
Revelator 4.5 Midrange

The 12M/4631G is a Revelator driver using the slit cone technology. Some of the slits are used to control cone resonance and the other set of slits add rigidity. This speaker also has the new dynamic linear suspension for lower compression and higher linearity. Every facet of this driver is designed to reduce resonance in all structures. A neodymium magnet has been chosen to reduce the depth, yet increase the magnetic energy.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 89 dB 75 Hz 3.2 ohm 0.22 mH 40W 49 cm2 38 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 3 & 7mm 5.3 Tm 6.5 g 0.6 kg 2.4 ltrs 5.57 0.35 0.33
12M/4631G 4
15M/4531K 4
The 15M/4531K is a 5 Revelator midrange. It features a slit-paper non-resonant cone and dust cap structure, dynamic linear suspension, SD-1 magnet system, Grasshopper cast chassis with maximized air flow, glass fiber voice coil former and resonance terminating mounting system. The 15M/4531K is intended for use as a midrange, with a usable frequency range between 100Hz and 6kHz. As you can see from the response curve, this speaker has a lot of energy in the upper frequency range.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 90 dB 35 Hz 3.5 ohm 0.17 mH 60W 95 cm2 38 mm 11 mm 5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 3 & 8mm 6.0 Tm 11 g 1.6 kg 24 ltrs 4.8 0.24 0.23
15W/4531G-00 4
The 15W/4531G-01 is a 5 Revelator mid/woofer. It features a slit-paper uncoated non-resonant cone and dust cap structure, dynamic linear suspension, SD-1 magnet system, Grasshopper cast chassis with maximized air flow, glass fiber voice coil former and resonance terminating mounting system. The 15W/4531G provides a more extended frequency response than its brothers, but still fantastic bass down to the mid 50s in a vented enclosure. This version is only available in 4 ohm.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 87 dB 40 Hz 3.4 ohm 0.25 mH 60W 95 cm2 38 mm 17.5 mm 5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 6.5 & 9mm 5.7 Tm 13 g 1.6 kg 15.8 ltrs 4.6 0.34 0.32
15W/8530K-00/01
The 15W/8530K-01 is a 5 Revelator mid/woofer. It features a non-resonant cone and dust cap structure, dynamic linear suspension, SD-1 magnet system, Grasshopper cast chassis with maximized air flow and resonance terminating mounting system. Less resonance in all structures, lower compression and higher linearity, faster termination of excess energy and higher sound pressure capability make the 15W have more musical and dynamic capability than any other 5 we know of. Wonderful bass in a small box!
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 85.5/84.5dB 30/32 Hz 5.8 ohm 0.35 mH 60W 95 cm2 38 mm 18 mm 5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 6.5 & 9mm 7/5.9 Tm 13 g 1.7/1.2 kg 27.4/24 ltrs 4.9/5.23 0.29/0.44 0.27/0.41
18W/4531G 4
The 18W/4531G-00 is a 7 Revelator mid/woofer. It features a non-resonant cone and dust cap structure, dynamic linear suspension, SD-1 magnet system, Grasshopper cast chassis with maximized air flow and resonance terminating mounting system. Less resonance in all structures, lower compression and higher linearity, faster termination of excess energy and higher sound pressure capability. The 18W/4531G should have an F3 of about 65Hz sealed and 40Hz vented. This is a popular driver for automotive applications.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter VC height Air gap height 90dB 33 Hz 3.4 ohm 0.3 mH 70W 150 cm2 38 mm 17.5 mm 5 Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 6.5 / 11 mm 5.7 Tm 17.5 g 1.7 kg 41.9 ltrs 5.2 0.38 0.35
18W/8531G 8
The 18W/8531G-00 is a 7 Revelator mid/woofer. It features a non-resonant cone and dust cap structure, dynamic linear suspension, SD-1 magnet system, Grasshopper cast chassis with maximized air flow and resonance terminating mounting system. Less resonance in all structures, lower compression and higher linearity, faster termination of excess energy and higher sound pressure capability. The 18W/8531G should have an F3 of about 50Hz sealed and 35Hz vented.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter VC height Air gap 87dB 28 Hz 5.8 ohm 0.35 mH 60W 150 cm2 38 mm 18 mm 5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 6.5 / 11 mm 6.8 Tm 17.5 g 1.7 kg 58.2 ltrs 5.1 0.39 0.36
22W/4851T 4
The 22W/4851T is a new addition to the Revelator line. This robust 8" woofer was designed to provide deep and accurate bass in a small enclosure. This woofer features a 2" voice coil on a titanium former, a low loss linear suspension and symmetric drive motor. The deep set hard paper cone is attached to the frame with a minimal reflection rubber surround. The 9mm X-max insures good linear travel. We suggest a 1.2 cubic foot enclosure with a 2" vent by 8" long for and F3 of 50Hz.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter VC height Air gap 89 dB 21 Hz 3.7 ohm 0.3 mH 170 W 220 cm2 50 mm 24 mm 6 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 9 / 14 mm 8.2 Tm 32.5 g 3.6 kg 126 ltrs 5.2 0.23 0.22
22W/8851T 8
The 22W/8851T is a new addition to the Revelator line. This robust 8" woofer was designed to provide deep and accurate bass in a small enclosure. This woofer features a 2" voice coil on a titanium former, a low loss linear suspension and symmetric drive motor. The deep set hard paper cone is attached to the frame with a minimal reflection rubber surround. The 9mm X-max insures good linear travel. We suggest a 1.2 cubic foot enclosure with a 2.5" vent by 8" long for and F3 of 38Hz.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter VC height Air gap 88 dB 21 Hz 6.2 ohm 0.35 mH 170 W 220 cm2 50 mm 24 mm 6 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 9 / 14 mm 9.9 Tm 31 g 3.6 kg 126 ltrs 5.1 0.26 0.25
22W/8857T 8
The 22W/885TT is a new addition to the Revelator line. This robust 8" woofer was designed to provide deep and accurate bass in a small enclosure. This woofer features a 2" voice coil on a titanium former, a low loss linear suspension and symmetric drive motor. The deep set black aluminum cone is attached to the frame with a minimal reflection rubber surround. The 9mm X-max insures good linear travel. We suggest a 1.2 cubic foot enclosure with a 2" vent by 8" long for and F3 of 38Hz.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter VC height Air gap 86 dB 23 Hz 6.2 ohm 0.35 mH 170 W 220 cm2 50 mm 24 mm 6 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 9 / 14 mm 10.1 Tm 37 g 3.6 kg 87.7 ltrs 4.9 0.32 0.30
26W/8861T 8
The 26W/8861T is a new addition to the Revelator line. This robust 10" woofer was designed to provide deep and accurate bass in a small enclosure. This woofer features a 2" voice coil on a titanium former, a low loss linear suspension and symmetric drive motor. The deep set hard paper cone is attached to the frame with a minimal reflection rubber surround. The 9mm X-max insures good linear travel. We suggest a 2.75 cubic foot enclosure with a 3" vent by 9.5" long for and F3 of 30Hz.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter VC height Air gap 88.5 dB 19 Hz 6.2 ohm 0.35 mH 170 W 320 cm2 50 mm 24 mm 6 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 9 / 14 mm 9.9 Tm 43.5 g 3.7 kg 234 ltrs 5.2 0.33 0.31
26W/4867T 4
The 26W/4867T a new black Aluminum cone woofer. Aluminum is a good material for subwoofer cones, very stiff and light. These cones reduce distortion and also help cool the voice coil, by conducting heat away from the coil. This woofer has a low loss suspension for increased bass response and the SD-1 motor system for less intermodulation distortion. Very rigid cast frame, large windows. We recommend a 2.5 cubic foot enclosure with a 3" diameter vent by 10" long, the F3 would be about 29Hz.
26W/8867T 8
The 26W/8867T a new black Aluminum cone woofer. Aluminum is a good material for subwoofer cones, very stiff and light. These cones reduce distortion and also help cool the voice coil, by conducting heat away from the coil. This woofer has a low loss suspension for increased bass response and the SD-1 motor system for less intermodulation distortion. Very rigid cast frame, large windows. We recommend a 2.3 cubic foot enclosure with a 3" diameter vent by 11" long, the F3 would be about 29Hz.
23W/4557T 4
The 23W/4557T is a very high end subwoofer, designed to be used with a passive radiator in a small enclosure. This sub has a very rigid aluminum cone, low loss rubber surround and cast frame. The passive radiator is similar, but with a weight attached to the bass of the cone. The 23W/4557T is using the SD-1 motor system. There are gold plated binding posts and the woofer is covered by a decorative rubber cap. Frequency response with the passive is down to 25Hz. One cubic foot sealed has an F3 of 33Hz. Also in black cone.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter VC height Air gap 82 dB 21 Hz 3.45 ohm 0.45 mH 225 W 232 cm2 50 mm 34 mm 8 mm Lin. & max. excursion 13 / 20 mm Force factor BL Product 9.3 Tm Moving mass incl. air 101 g Net weight 4.6 kg Vas 45 ltrs Qms 4.8 Qes 0.52 Qts 0.47 Black cone part# 23W/4557T-02
23W/0-00 Passive
This is the passive radiator intended for use with the 23W/4557T active woofer. We recommend putting both in a 1.0 cubic foot enclosure. This should yield a bass response down to 25Hz. The woofer should still be linear at 180 watts and have an output of about 104dB. The curve below is a simulation of the woofer and passive radiator in a 1.0 cubic foot box. This was done in Bass Box Pro by Harris Technologies. Also in black cone.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter VC height Air gap dB 11 Hz - ohm - mH - W 232 cm2 - mm max. excursion 20 mm Force factor BL Product - Tm Moving mass incl. air 400 g Net weight 1.2 kg Vas 43.3 ltrs Qms 11.5 Qes Qts Black cone part# 23W/0-00-02
D2008/8512
Similar to the D2008, but with several improvements, a foam impregnated front face plate and a lower resonance. Double chambered 3/4" damped textile dome tweeter with the same diaphragm and voice coil as the D2008. The lower resonance of this driver will allow it to be crossed over lower than most other 3/4" dome tweeters, yet retain the low distortion and clarity of a 3/4" dome. We recommend a steeper x-over slope be used when the x-over point is below 3KHz.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height
88dB 800 Hz 5.7 ohm 0.08 mH 150W@4K 3.8 cm2 19 mm 3.1 mm 2 mm
Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts
0.7 / 1.2 mm 2.4 Tm 0.25 g 0.4 kg 1.26 1.24 0.63
D2010/8513
Similar to the D2008, but with several improvements, a foam impregnated front face plate and a lower resonance. Double chambered 3/4" damped textile dome tweeter with the same diaphragm and voice coil as the D2008. The lower resonance of this driver will allow it to be crossed over lower than most other 3/4" dome tweeters, yet retain the low distortion and clarity of a 3/4" dome. We recommend a steeper x-over slope be used when the x-over point is below 3KHz.
D2905/9300 1" Dome Tweeter

The D2905/9300 is a 1 textile dome tweeter with a very flat frequency response and low distortion. The D2905/9300 achieves a lower resonance and increased clarity by using several coatings of damping material on the dome and chambering behind the dome. Both these damping factors and the use of a light magnetic fluid, reduce the resonances as much as possible, while reducing compression affects. this tweeters linear response and openness make it a good choice for any system.
0.7 / 1.2 mm 2.4 Tm 0.25 g 0.4 kg 1.26 1.24 0.63 TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 90dB 650 Hz 4.7 ohm 0.08 mH 150W@2.5K 8.5 cm2 28 mm 3.3 mm 2.5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 0.4 / 1.5 mm 3.5 Tm 0.45 g 0.7 kg 0.94 0.72 0.41
88dB 800 Hz 5.7 ohm 0.08 mH 150W@4K 3.8 cm2 19 mm 3.1 mm 2 mm
D2905/9500 1" Dome Tweeter

The D2905/9500 is similar to the D2905/9300, but with non-resonant chamber. The optimized pole piece geometry reduces flow resistance and the anti-resonator-plug in the rear chamber eliminates turbulence. A light ferrofluid is used in the air gap to ensure optimal linear mechanical behavior and minimal micro-dynamic non-linearity. This tweeter has a smooth transparent sound and very low levels of distortion. A perfect choice for any high end system.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 90dB 550 Hz 4.7 ohm 0.07 mH 150W@2.5K 8.5 cm2 28 mm 3.3 mm 2.5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 0.4 / 1.5 mm 3.5 Tm 0.45 g 0.7 kg 1.04 0.60 0.38
D2905/9700 1 Dome Tweeter

The D2905/9700 uses the same hand coated dome and voice coil of the D2905/9500, but uses the motor system of the Revelator. The Symmetric Drive technology eliminates almost all electrical phase shift. The carefully machined top plate minimize air noise and compression. Copper caps act as heat conductors. High power handling is achieved without ferrofluid and improves micro-dynamic linearity. The tweeter has excellent dynamic and detailing capability.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter V.C. height Air gap height 89.5dB 500 Hz 4.7 0.01 mH 225W@2.8kHz 8.5 cm2 28 mm 3.3 mm 2.5 mm Lin. & max. excursion BL Moving mass incl. air Net weight Vas Qms Qes Qts 0.4/ 1.5 mm 3.5 Tm 0.45 g 0.7 kg 3.45 0.54 0.47
D2904/9800 4
The D2904/9800 is a high-end 1 aluminum dome tweeter. The magnet system uses the Symmetric Drive technology that almost eliminates electrical phase shift. The specially designed chamber reduces air noise and compression. The geometry of the dome causes the break-up to appear beyond the audible range. A specially designed diffusor is used to equalize the response in the upper octave. The tweeter has a very clear and open sound.
D3806/8200 1.5" Dome Mid/Tweeter

The D3806/8200 is a 1.5 textile dome mid/tweeter. The large dome allows for a lower crossover point. Large dome typically have better transient response too. This tweeter is a good choice for use in a system where a lower crossover point is required, or where an upper mid is needed. This tweeter has the SD motor system for reduced distortion and a tuned rear chamber. Flange is 125mm in diameter, 91mm cut out diameter and 47mm depth.
0.1 / 1.5 mm 2.8 Tm 0.50 g 0.7 kg 3.09 0.84 0.66 TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 89dB 450 Hz 5.7 ohm 0.04 mH 100W@1.5K 14 cm2 38 mm 3.2 mm 2.5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 0.4 / 1 mm 3.8 Tm 0.9 g 1.1 kg 0.93 1.00 0.48
88dB 500 Hz 3.5 ohm 0.01 mH 160W@2.8K 8.5 cm2 28 mm 2.5 mm 2.5 mm
18W/8535 7" Carbon/Paper Woofer

The 18W/8535 woofer features the SD-1 magnet system which almost eliminates modulation and dynamic distortion and reduce clipping when the drivers is taken beyond linear excursion. The carbon fiber filled paper cone is impregnated and coated to damp resonance. The low loss rubber surround combines dynamic linearity with low coloration. The smaller magnet increases the Qts making this driver a good choice for a sealed enclosure.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter V.C. height Air gap height 86.5dB 26 Hz 5.8 ohm 0.3 mH 70W 145 cm2 38 mm 15 mm 5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 5 / 10 mm 5.7 Tm 15.5 g 2.5 kg 71.2 liters 2.50 0.45 0.38
18W/8542
7" Paper Cone Woofer
The 18W/8542 is a classic paper cone woofer with foam surround. The back coated paper cone delivers smooth and warm sound reproduction. The speaker is intended for high end 2-way systems in bass reflex enclosures. This woofer has the large Symetric Drive (SD) magnet system for reduced distortion. The surround is made of double coated foam material with long term stability. A coating is used to dampen unwanted resonances where the surround is attached to the cone.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter V.C. height Air gap height 89dB 30 Hz 5.5 ohm 0.2 mH 70W 135 cm2 42 mm 19 mm 6 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 6.5 / 10mm 7.8 Tm 15 g 2.3 kg 47.9 liters 1.7 0.26 0.23
18W/8545
7" Carbon fibre Paper Woofer
This 7" features the heavily damped and carbon fibre impregnated paper cone that dampens resonances normally associated with stiff cones. The magnet system is the new SD-1 system which eliminates modulation and dynamic distortion, as well as clipping distortion created as it exceeds its maximum linear excursion. These designs all together make a drive unit with a very open sound with excellent detailing combined with low coloration and very precise imaging. Cast frame, rubber surround.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter V.C. height Air gap height 88dB 28 Hz 5.5 ohm 0.4 mH 100W 145 cm2 42 mm 19 mm 6 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 6.5 / 10mm 8.0 Tm 20 g 2.3 kg 47.6 liters 2.30 0.30 0.27
18W/8545K
7" Carbon fibre Paper Woofer
This 7" features the heavily damped and carbon fibre impregnated paper cone that dampens resonances normally associated with stiff cones. The magnet system is the new SD-1 system which eliminates modulation and dynamic distortion, as well as clipping distortion created as it exceeds its maximum linear excursion. This driver uses a fiberglass voice coil former. Try it in a 1/2 cubic foot box with a 1.5" diameter vent by 5.2" long, f3 48Hz.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power Effective cone area V.C. diameter V.C. height Air gap height 87.5dB 28 Hz 5.5 ohm 0.4 mH 100W 145 cm2 42 mm 19 mm 6 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts 6.5 / 10mm 8.2 Tm 20.5 g 2.4 kg 46.4 liters 5.20 0.30 0.28
D2606/9200 6
The D2606/9200 is a 1" coated silk fabric dome tweeter. This tweeter uses ferrofluid to cool the voice coil and reduce the resonance peak. The linear response face plate provides a very smooth response at a fairly high sensitivity. The voice coil is attached to the leads by a high power braided tinsel lead wire. A damped cavity in the pole pieces reduces reflections and lowers the resonance frequency. The tweeter has field repairable voice coil assembles (600058). This tweeter was previously produced under the part number D27TG15-06 and could be a good replacement for D26TG05 tweeters too, but with 5 screw holes instead of 4.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 91.4dB 1100 Hz 4.6 ohm 0.04 mH 100W@2.5K 7.1 cm2 26 mm 1.6 mm 2.5 mm Lin. & max. excursion Air gap flux density Force factor BL Product Moving mass incl. air Outside diameter Cutout diameter Flange thickness Depth Screw Circle 0.2 / 1.6 mm 2.7 Tm 0.3 g 104 mm 72 mm 4.2 mm 27.1 mm 94 mm
D2606/9220 6
The D2606/9220 is a 1" coated silk fabric dome tweeter. This tweeter uses ferrofluid to cool the voice coil and reduce the resonance peak. The large rear chamber provides a low resonance frequency and reduces reflections. The low fs allows for a lower crossover point. by a high power braided tinsel lead wire. The tweeter has field repairable voice coil assembles (600058). This tweeter can be used to be produced under the part number D27TG35-06 and is a good replacement for older D26TG35 tweeters. It can also replace the D27TG45, but with 4 screw holes instead of 5.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 91.4dB 850 Hz 4.6 ohm 0.01 mH 100W@2K 7.1 cm2 26 mm 2.1 mm 2.5 mm Lin. & max. excursion Air gap flux density Force factor BL Product Moving mass incl. air Outside diameter Cutout diameter Flange thickness Depth Screw Circle 0.2 / 1.6 mm 2.8 Tm 0.33 g 104 mm 72 mm 4.2 mm 38.9 mm 94 mm
D2604/8330 4
The D2604/8330 is a 1" textile dome with a large roll surround which provides extended frequency response above 40kHz. The double magnet provide greater efficiency as well as a chamber to reduce reflections and lower the resonance frequency. The tweeter uses high temperature copper-clad aluwire. The tweeter also has a well behaved roll off on the low end, which should allow the tweeter to use more simplified crossovers. The off axis response is also very good, making this tweeter a good choice for automotive systems too. The low fs allows for a lower crossover point.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 93 dB 475 Hz 2.8 ohm 0.04 mH 100W@2K 8 cm2 25 mm 2.0 mm 2.5 mm Linear excursion Air gap flux density Force factor BL Product Moving mass incl. air Outside diameter Cutout diameter Flange thickness Depth Screw Circle 0.3 mm - Tm 0.42 g 104 mm 72 mm 5 mm 54.6 mm 92 mm
D2608/9130 8
The D2608/9130 has a very light 1" textile dome with high internal damping. The optimized magnet system feature dual magnets, low compression and magnetic cooling fluid. The magnet system is designed to reduce reflections and turbulence. The face plate is black die cast aluminum. The 8 ohm impedance, yet high efficiency of 91.3dB makes this a rather unique tweeter. The low resonance frequency and magnetic fluid will allow for a low crossover point. This tweeter is a good choice for all high end speaker systems.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 91.3dB 700 Hz 5.6 ohm 0.04 mH 100W@2K 7 cm2 26 mm 1.5 mm 2.5 mm Linear excursion Air gap flux density Force factor BL Product Moving mass incl. air Outside diameter Cutout diameter Flange thickness Depth Screw Circle 0.5 mm - Tm -g 104 mm 72 mm 4.5 mm 32.3 mm 92 mm
R2604/8320 4
The R2604/8320 features the unique dual ring radiator diaphragm made from coated silk fabric. The tweeter also uses a patented wave guide center plug to reduce distortion. The low resonance frequency allows for a low crossover point. A special chamber lowers the fs and reduces internal reflections. The frequency range extends beyond 40kHz! Copper-clad aluwire assures good power handling at lower crossover points. This tweeter has quickly become a favorite with loudspeaker designers. The D2604/8320 used to be produced under the part number XT25TG30.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 90 dB 550 Hz 2.9 ohm 0.02 mH 100W@2.5K 5.4 cm2 25 mm 2.2 mm 2.5 mm Linear excursion Air gap flux density Force factor BL Product Moving mass incl. air Outside diameter Cutout diameter Flange thickness Depth Screw Circle 0.2 mm - Tm 0.3 g 104 mm 72 mm 5 mm 39.8 mm 92 mm
R2604/8330 4
The R2604/8330 features the unique dual ring radiator diaphragm made from coated silk fabric. The tweeter also uses a patented wave guide center plug to reduce distortion. The low resonance frequency allows for a low crossover point. A special chamber lowers the fs and reduces internal reflections. The frequency range extends beyond 40kHz! Copper-clad aluwire assures good power handling at lower crossover points. The Double magnet increases efficiency and extends the upper frequency range. The D2604/8330 used to be produced under the part number XT25BG60.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 92 dB 440 Hz 2.9 ohm 0.02 mH 100W@2.5K 5.4 cm2 25 mm 2.2 mm 2.5 mm Linear excursion Air gap flux density Force factor BL Product Moving mass incl. air Outside diameter Cutout diameter Flange thickness Depth Screw Circle 0.2 mm - Tm 0.3 g 104 mm 72 mm 5 mm 54.6 mm 92 mm
D7608/9200-10 8
The D7608/9200-10 is one of the last remaining 3" textile dome tweeters. A textile dome mid is a perfect choice for upper midrange where fast action is required. The pre-coated fabric dome has a very smooth and natural sounding response. The 3" voice coil provides good transient response and heat dispersion. An internal grill is used to protect the dome from being pushed in. The rear plate is perforated with holes, so the midrange requires the use of a 1 to 2 liter sealed and stuffed chamber (not included). This midrange has exceptional off axis response and would be good in a car if you can work out a chamber.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power 12dB@Hz Effective cone area V.C. diameter V.C. height Air gap height 92.0dB 300 Hz 5.7 ohm 0.13 mH 80W@500Hz 55 cm2 76 mm 2.9 mm 2.0 mm Linear excursion 0.4.5 mm Force factor BL Product 4.7 Tm Moving mass incl. air 3.3 g Outside diameter 152 mm Cutout diameter 115.5 mm Flange thickness 4 mm Depth 25.6 mm Screw Circle 134 mm ***Must use with 1 to 2 liter chamber
4" Fiberglass Cone Midrange

The Discovery series is designed for the discerning audiophile customer. The coated fiberglass cone reduces vibration and standing waves, and the vented motor system minimizes power compression. The combined result is a very open and dynamic sound. This midrange also features a strong neodymium magnet, NR surround and aluminum chassis. In 1 liter sealed your F3 is 275Hz, in 1.2 liters vented, 1"vent diameter x 3", your F3 is 125Hz. This driver has a very extended response.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power RMS Effective cone area V.C. diameter V.C. height Air gap height 89.8dB 90 Hz 3.2 ohm 0.1 mH 15W 36 cm2 20 mm 9.2 mm 4 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts Cms 2.6 / 7mm 3.9 Tm 2.8 g 0.3 kg 2.0 liters 3.20 0.32 0.29 1.1 mm/N
10F/4424G 4
4" Fiberglass Cone Midrange

The Discovery series is designed for the discerning audiophile customer. The coated fiberglass cone reduces vibration and standing waves, and the vented motor system minimizes power compression. The combined result is a very open and dynamic sound. This midrange also features a strong neodymium magnet, NR surround and aluminum chassis. In 1 liter sealed your F3 is 275Hz, in 1.2 liters vented, 1"vent diameter x 3", your F3 is 125Hz. This driver has a very extended response.
10F/8424G 8
5.25" Fiberglass Cone Mid

The Discovery series is designed for the discerning audiophile customer. The coated fiberglass cone reduces vibration and standing waves. The phase plug improves linearity and eliminates distortion caused by reflections that occur behind dust caps. The coated foam surround improves sensitivity. Highlights: Aluminum Chassis, Fiberglass cone, coated foam surround, raised spider, aluminum shorting ring Flange 149mm, cutout 114mm, depth 60.9mm. Use in small sealed enclosure.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power RMS Effective cone area V.C. diameter V.C. height Air gap height 92.4 dB 100 Hz 3.2 ohm 0.23 mH 75W 80 cm2 25 mm 8 mm 5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts Cms 1.5 / 8mm 5.3 Tm 6.2 g 1.0 kg 3.7 liters 5.62 0.47 0.43 0.41 mm/N
15M/4624G 4
12W/4524G 4 4.5" Fiberglass Cone Woofer

The Discovery series is designed for the discerning audiophile customer. The coated fiberglass cone reduces vibration and standing waves, and the vented motor system minimizes power compression. Suitable as small woofer or midrange in a larger system. Driver Highlights: Aluminum Chassis, Fiberglass cone, NR rubber surround, Raised spider, shorting ring Flange 124.7mm, cutout 100mm, depth 58.4mm. Use vented for use as a woofer or sealed for use as a midrange.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power RMS Effective cone area V.C. diameter V.C. height Air gap height 88.8dB 50 Hz 3.1 ohm 0.4 mH 40W 59 cm2 25 mm 10 mm 4 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts Cms 3 / 9mm 4.4 Tm 6.1 g 1.0 kg 8.2 liters 3.35 0.30 0.27 1.67 mm/N

The Discovery series is designed for the discerning audiophile customer. The coated fiberglass cone reduces vibration and standing waves, and the vented motor system minimizes power compression. Suitable as small woofer or midrange in a larger system. Driver Highlights: Aluminum Chassis, Fiberglass cone, NR rubber surround, Raised spider, shorting ring Flange 124.7mm, cutout 100mm, depth 58.4mm. Use vented for use as a woofer or sealed for use as a midrange.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power RMS Effective cone area V.C. diameter V.C. height Air gap height 85.8 dB 52 Hz 5.7 ohm 0.6 mH 40W 59 cm2 25 mm 10 mm 4 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts Cms 3 / 10mm 5.4 Tm 5.6 g 1.0 kg 8.2 liters 3.42 0.35 0.32 1.67 mm/N
5.25" Fiberglass Cone Woofer

The Discovery series is designed for the discerning audiophile customer. The coated fiberglass cone reduces vibration and standing waves, and the vented motor system minimizes power compression. The combined result is a very open and dynamic sound. Driver Highlights: Aluminum Chassis, Fiberglass cone, NR rubber surround, Raised spider, shorting ring Flange 149mm, cutout 114mm, depth 60.9mm. In 4 liter box with 1.5" diameter vent by 4" long, F3 is 80Hz.
15W/4434G 4

The Discovery series is designed for the discerning audiophile customer. The coated fiberglass cone reduces vibration and standing waves, and the vented motor system minimizes power compression. The combined result is a very open and dynamic sound. Driver Highlights: Aluminum Chassis, Fiberglass cone, NR rubber surround, raised spider, shorting ring Flange 149mm, cutout 114mm, depth 60.9mm. In 4 liter box with 1.5" diameter vent by 4" long, F3 is 80Hz.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power RMS Effective cone area V.C. diameter V.C. height Air gap height 869 dB 45 Hz 5.7 ohm 0.8 mH 60W 80 cm2 32 mm 13.4 mm 5 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts Cms 4.2 / 8mm 7.3 Tm 8.61 g 1.2 kg 12.8 liters 3.74 0.27 0.25 1.43 mm/N
15W/8434G 8

The Discovery series is designed for the discerning audiophile customer. The coated fiberglass cone reduces vibration and standing waves, and the vented motor system minimizes power compression. The combined result is a very open and dynamic sound. Driver Highlights: Aluminum Chassis, Fiberglass cone, NR rubber surround, Raised spider, shorting ring Flange 179.6mm, cutout 144.3mm, depth 73.2mm. In 15 liter box with 2" diameter vent by 4.5" long, F3 is 55Hz.
18W/4434G 4

The Discovery series is designed for the discerning audiophile customer. The coated fiberglass cone reduces vibration and standing waves, and the vented motor system minimizes power compression. The combined result is a very open and dynamic sound. Driver Highlights: Aluminum Chassis, Fiberglass cone, NR rubber surround, Raised spider, shorting ring Flange 179.6mm, cutout 144.3mm, depth 73.2mm. In 15 liter box with 2" diameter vent by 4.5" long, F3 is 55Hz.
8" Fiberglass Cone Woofer

The Discovery series is designed for the discerning audiophile customer. The coated fiberglass cone reduces vibration and standing waves, and the vented motor system minimizes power compression. The combined result is a very open and dynamic sound. Driver Highlights: Aluminum Chassis, Fiberglass cone, NR rubber surround, Raised spider Flange 225mm, cutout 185mm, depth 84.5mm. In 35 liter box with 2" diameter vent by 4" long, F3 is 45Hz.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power RMS Effective cone area V.C. diameter V.C. height Air gap height 92.4dB 30 Hz 3.0 ohm 0.33 mH 70W 235 cm2 38 mm 17.3 mm 6 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts Cms 5.7 / 12mm 6 Tm 23.7 g 2.1 kg 95 liters 3.70 0.37 0.34 1.23 mm/N
22W/4534G 4

22W/8434G 8

TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power RMS Effective cone area V.C. diameter V.C. height Air gap height 90.5 dB 23 Hz 3.8 ohm 0.70 mH 70W 350 cm2 38 mm 18 mm 6 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts Cms 6 / 12mm 8.8 Tm 52 g 2.9 kg 156 liters 9.57 0.37 0.36 0.92 mm/N
26W/4534G 4

TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power RMS Effective cone area V.C. diameter V.C. height Air gap height 89 dB 23 Hz 5.7 ohm 0.96 mH 70W 350 cm2 38 mm 18 mm 6 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts Cms 6 / 12mm 10.1 Tm 50.5 g 2.9 kg 150 liters 9.12 0.42 0.40 0.95 mm/N
26W/8534G 8
10" Aluminum Subwoofer

This Discovery 10" subwoofer has many fantastic features. The cone is black anodized aluminum for stiffness. The dust cap is a layered paper and fiberglass. An aluminum shorting ring and aluminum pole piece extension is used to reduce distortion and power compression. A Titanium voice coil former improves power handling. The voice coil is vented below the spider and behind the dust cap for added VC cooling. Us in 2 cubic feet with 3" vent by 10" long for an F3 of 30Hz.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power RMS Effective cone area V.C. diameter V.C. height Air gap height 88dB 21 Hz 2.6 ohm 0.83 mH 150W 352 cm2 51 mm 33 mm 8 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Magnet weight Vas Qms Qes Qts Cms 12.5/28mm 10.5 Tm 105 g 2.25 kg 94.9 liters 5.56 0.33 0.31 0.55 mm/N
26W/4558T 4
26W/0-00
10" Aluminum Cone
Passive Radiator
This passive is built similarly to the active woofer. Same black anodized aluminum cone, paper/fiberglass dust cap, cast frame, low damping large roll rubber surround and Nomex spider. In place of the voice coil, a weight is added to tune the passive radiator to 11Hz. More mass could be added to the weight, but too much mass will make the passive sluggish and may reduce the live of the product.
TECHNICAL DATA: Free air resonance Fs Effective cone area Max excursion Moving mass incl. air Vas Qms Cms Rms 11 Hz 352 cm2 28mm 400 g 95 liters 13.7 0.55 mm/N 1.97 kg/s
When paired with the 26W/4558T woofer in a 1 cubic foot box and an amplifier with a 25Hz boost, your F3 will be about 35Hz. Without a boost the F3 is about 45Hz. When using the 1 cubic foot box with passive radiator in a car, without any boost and with 6dB of cabin gain, your F3 is about 19Hz. This should be very impressive in a car environment.
12" Aluminum Subwoofer

This Discovery 12" subwoofer has many fantastic features. The cone is black anodized aluminum for stiffness. The dust cap is a layered paper and fiberglass. An aluminum shorting ring and aluminum pole piece extension is used to reduce distortion and power compression. A Titanium voice coil former improves power handling. The voice coil is vented below the spider and behind the dust cap for added VC cooling. Us in 2.5 cubic feet with 3" vent by 12" long for an F3 of 30Hz.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power RMS Effective cone area V.C. diameter V.C. height Air gap height 89dB 17 Hz 2.6 ohm 0.83 mH 150W 466 cm2 51 mm 33 mm 8 mm Lin. & max. excursion Force factor BL Product Moving mass incl. air Magnet weight Vas Qms Qes Qts Cms 12.5/ 28mm 10.5 Tm 135 g 2.25 kg 197 liters 5.01 0.34 0.32 0.65 mm/N
30W/4558T 4
30W/0-00
12" Aluminum Cone
Passive Radiator
This passive is built similarly to the active woofer. Same black anodized aluminum cone, paper/fiberglass dust cap, cast frame, low damping large roll rubber surround and Nomex spider. In place of the voice coil, a weight is added to tune the passive radiator to 11Hz. More mass could be added to the weight, but too much mass will make the passive sluggish and may reduce the live of the product.
TECHNICAL DATA: Free air resonance Fs Effective cone area Max excursion Moving mass incl. air Vas Qms Cms Rms 9.5 Hz 466 cm2 28mm 435 g 200 liters 14 0.65 mm/N 1.84 kg/s
When paired with the 30W/4558T woofer, we recommend a 2.0 to 2.5 cubic foot box for an F3 of about 30Hz. This F3 is about the same wether you use a boost on the amp or not. If not using a 25Hz boost, you will have a leaner and tighter bass and with the boost you will have a more pronounced bass. You can also use this passive with the 26W/4558T in a 1.5 cubic foot box with a similar F3 of 35Hz, but with a 2dB gain in efficiency from the 10" passive.
P13WH00 8 5" Poly Cone Woofer

This classic 5" Vifa woofer now being built by Scan-speak was used in many DIY and commercial systems over the years. The P13WH00 has a mineral filled poly cone, rubber surround and cast frame. You might choose this as a replacement for similar Vifa drivers in the 140mm frame size. We understand this to be the last production run of this speaker. You can use this driver in a 6 liter box with a 1.5" diameter port by 4.5" long for an F3 of 83Hz.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power RMS Effective cone area V.C. diameter V.C. height Air gap height 88 dB 60 Hz 5.7 ohm 0.7 mH 40W 86 cm2 25 mm 14 mm 6 mm Linear excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts Cms 4mm 6 Tm 7.5 g - kg 10 liters 1.38 0.43 0.33 - mm/N
6.5" Poly Cone Woofer

This classic 6.5" Vifa woofer now being built by Scan-speak was perhaps the most popular driver in the world at one time. This classic woofer was used in many commercial products. The P17WJ00 has a mineral filled poly cone, rubber surround and cast frame. This woofer should be considered as a good replacement for other classic Vifa and Seas woofers in the same frame size. You can use this woofer in a 15 liter box with a 2" diameter port by 7" long for an F3 of 55Hz.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power RMS Effective cone area V.C. diameter V.C. height Air gap height 88dB 37 Hz 5.8 ohm 0.55 mH 40W 136 cm2 32 mm 14 mm 6 mm Linear excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts Cms 4mm 6.5 Tm 14 g - kg 34.7 liters 1.55 0.45 0.35 - mm/N
P17WJ00 8
History P21WO20 8
Founded in 1970, Scan-Speak still resides at our original address in Videbaek, Denmark. Located in the heart of the Jutland peninsula, our acoustic engineers adhere to our legendary policy of "Never compromise". We never compromise on our product quality, sound quality or pursuit of perfection in a given application. We set the loudspeaker industry's gold standard for audiophiles, and are constantly viewed as a market benchmark by other high-end speaker manufacturers. For close to 40 years, Scan-Speak has been on a quest to create transducers that reveal the finest details in recordings, concealing nothing from the listener. This quest has resulted in several revolutionary inventions, where distortion in the magnet systems and the moving parts of the speaker is minimized. Our philosophy is simple: the emitted sound must be dynamic, giving a transient response and providing tonal balance. Scan-Speak transducers have righteously been called "the best that money can buy", and we agree fully. All our transducers are hand-built with the utmost attention to quality at their core. Their prices reflect this, providing solutions targeted towards high-end audiophile applications. Needless to say, Scan-Speak is dedicated to proving an unwavering high-quality in manufacturing.
8" Poly Cone Woofer

This classic 8" Vifa woofer now being built by Scan-speak. This classic woofer was used in many commercial products. The P21WO20 has a mineral filled poly cone, rubber surround and cast frame. This woofer should be considered as a good replacement for other classic Vifa and Seas woofers in the same frame size. You can use this woofer in a 45 liter box with a 3" diameter port by 8" long for an F3 of 40Hz.
TECHNICAL DATA: Sensitivity 2.83V/1M Free air resonance Fs DC resistance V.C. inductance Power RMS Effective cone area V.C. diameter V.C. height Air gap height
91 dB 28 Hz 5.7 ohm 0.9 mH 80W 235 cm2 40 mm 14 mm 6 mm
Linear excursion Force factor BL Product Moving mass incl. air Net weight Vas Qms Qes Qts Cms
4mm 7.4 Tm 22.5 g - kg 113 liters 1.6 0.41 0.33 - mm/N
820012 Autosound 5" Car Component System

130mm Mid/Woofers "EURO-DIN" Aluminum Die Cast Basket Neodymium Magnet System Vented Pole Piece Black Coated NRSC* Fiberglass Cone Low Loss Rubber Surround The Discovery car audio systems 19mm Ring Dome Tweeters have been designed with the same Wedge Housing Flange and Nut for Flush Mounting engineering and attention to detail that has made their home speakers Crossovers (2nd Order @ 2500Hz) famous. The standard frame size of the Grill, Cables and Screws woofer and the two mounting *Non-Resonant-Suspension-Coupled options for the tweeter should make for an easy installation. Reduces breakup modes.
SYSTEM DATA: Nominal Impedance Sensitivity 2.83V/1M Frequency Range Crossover frequency WOOFER DATA: Free air resonance Fs Effective cone area Sd V.C. diameter Linear excursion Force factor BL Product Moving mass incl. air Vas Qms Qes Qts Weight Woofer diameter At mounting tabs Cut out diameter Depth Screw mount diameter Flange thickness TWEETER DATA: Free air resonance Fs Effective cone area Sd Voice coil diameter Weight Tweeter diameter Cut out diameter Depth Overall thickness Surface or Wedge mount 25.4mm = 1" 130 mm 152 mm 113 mm 52 mm 138 mm +2.5 3.8 mm 1000Hz 3.8 cm2 19mm 60 g 42 mm 39 mm 18 mm 26 mm
820013 Autosound 6" Car Component System

165mm Mid/Woofers "EURO-DIN" Aluminum Die Cast Basket Neodymium Magnet System Vented Pole Piece Black Coated NRSC* Fiberglass Cone Low Loss Rubber Surround The Discovery car audio systems 19mm Ring Dome Tweeters have been designed with the same Wedge Housing Flange and Nut for Flush Mounting engineering and attention to detail that has made their home speakers Crossovers (2nd Order @ 3000Hz) famous. The standard frame size and Grill, Cables and Screws multiply mounting options of the *Non-Resonant-Suspension-Coupled woofer and the two mounting options for the tweeter should Reduces breakup modes. make for an easy installation.
SYSTEM DATA: Nominal Impedance Sensitivity 2.83V/1M Frequency Range Crossover frequency WOOFER DATA: Free air resonance Fs Effective cone area Sd V.C. diameter Linear excursion Force factor BL Product Moving mass incl. air Vas Qms Qes Qts Weight 4 ohm 90dB 60Hz - 28kHz 3000Hz/12dB 55 Hz 138 cm2 32 mm 4mm 4.8 Tm 12.5 g 12.6 liters 3.06 0.56 0.48 590 g Woofer diameter Cut out diameter Depth Screw mount diameter Flange thickness TWEETER DATA: Free air resonance Fs Effective cone area Sd Voice coil diameter Weight Tweeter diameter Cut out diameter Depth Overall thickness Surface or Wedge mount 25.4mm = 1" 165.5 mm 141 mm 63 mm 156.5 mm +.75 3.3 mm 1000Hz 3.8 cm2 19mm 60 g 42 mm 39 mm 18 mm 26 mm
4 ohm 88dB 70Hz - 28kHz 2500Hz/12dB 80 Hz 80 cm2 32 mm 4mm 4.8 Tm 10 g 4.6 liters 4.41 0.65 0.57 510 g
Driver Dimensions in Millimeters A B Unit 55.5 5 D2004/6020-00, R2004/6020-00 61.9 5 D3004/6020-00, R3004/6020-00 61.9 5 D3004/6020-10, R3004/6020-10 104 5 D3004/6640-00, D3004/6600-00 104 5 D3004/6620-00, D3004/6620-01 104 5 R3004/6620-00, R3004/6620-01 104 5.9 R2904/7000, D2904/7100 130 5 D2905/9900 92 3.5 D2008/8512 98 5 D2010/8513 104.5 3 D2905/9300, 9500, 9700 104.5 3 D2904/9800 125 4 D3806/8200 104 4.2 D2606/9200 Discovery 104 4.2 D2606/9220 Discovery 104 5 D2604/8330 Discovery 104 4.5 D2608/9130 Discovery 104 5 R2604/8320 Discovery 104 4 R2604/8330 Discovery 152 4 D7608/9200-10 Discovery Mid 97.5 3.5 10F's Discovery 120 4 12MU's Illuminator 115.5 3 12M's Revelator 124.7 5 12W's Discovery
C 29.3 21.5 55.4 23 23 23 25 48 37.5 41 41 43 45 27.1 38.9 54.6 32.3 39.8 54.6 25.6 40 70 48.4 58.4
D 42.1 48.5 48.5 77 77 77 70 90 69 69 74 74 92 72 72 72 72 72 72 115.5 78 101 92 100
Driver Dimensions in Millimeters A B Unit 130 6 13M's Classic 149 4.8 15M & W's Discovery 148 6 15M's Revelator 148 6 15W's Revelator 149 6.5 15WU's Illuminator 179.6 5.2 18W's Discovery 182 5.5 18W's Revelator 177 4 18W's Classic 184 7.5 18WU's Illuminator 225 5.2 22W's Discovery 222 7 22W's Revelator 255 6 23W's Revelator 255 6 23W's Passives 255 6 25W's Classic 272 5.6 26W's Discovery 270 5 26W Discovery Subwoofer 270 5 26W Discovery Passive 260 7 26W's Revelator 308 5 30W Discovery Subwoofer 308 5 30W Discovery Passive 42 8 820012 & 820013 tweeter 130 3.8 820012 woofer 165.5 3.3 820013 woofer 130 3 Flow Resistor (SSV)
C 45.5 61.9 71 71 90 73.2 77 70 97.3 84.5 111 135 73 86 100.4 135.5 70.9 124.7 144.3 80 18 52 63 19
D 103 114 125 125 123 144.3 156 158 158 185 194 225 225 228 231 240 240 228 280 280 39 113 141 109
25.4mm = 1" 28.3 liters = 1 cubic foot 1 cubic foot = 1728 cubic inches Box Volume = L x W x H We can assist you with your speaker design.
Founded in 1970, Scan-Speak is one of the oldest and most experienced loudspeaker manufacturers in the world. Their "Never Compromise" philosophy assures you as a customer that the product will be engineered and built to exceptional standards. Please visit the Scan-speak website for a history of the company, as well as the most updated news, information and specifications.
www.scan-speak.dk

Scanspeak Full V10

Uploaded by

Copyright:

Available Formats

Scanspeak Full V10

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Scanspeak Full V10

Uploaded by

Copyright:

Available Formats

Model

Illuminator Series Tweeters

Illuminator Series Midranges

Illuminator Series Woofers

Revelator Series Tweeters

Revelator Series Midranges

Revelator Series Mid/Bass & Woofers

0.44 43.5 0.44 43.5

Classic Series Tweeters

Price Each $192.00

Classic Series Mid/Tweeter

Classic Series Woofers

Discovery Series Dome Tweeters

Discovery Series Midranges

Discovery Series Woofers

Discovery Series Subwoofers and Passive Radiators

Discovery Series Autosound Component Systems

Classic Vifa Drivers Built by Scan-Speak

Illuminator 4.5" 12MU/4731T-00 4

Illuminator 4.5" 12MU/8731T-00 8

Illuminator 5.25" 15WU/4741T-00 4

Illuminator 5.25" 15WU/8741T-00 8

Illuminator 6.5" 18WU/4741T-00 4

Illuminator 6.5" 18WU/8741T-00 8

Illuminator 6.5" 18WU/4747T-00 4

Illuminator 6.5" 18WU/8747T-00 8

Revelator 4.5 Midrange

88dB 800 Hz 5.7 ohm 0.08 mH 150W@4K 3.8 cm2 19 mm 3.1 mm 2 mm

0.7 / 1.2 mm 2.4 Tm 0.25 g 0.4 kg 1.26 1.24 0.63

D2905/9300 1" Dome Tweeter

88dB 800 Hz 5.7 ohm 0.08 mH 150W@4K 3.8 cm2 19 mm 3.1 mm 2 mm

D2905/9500 1" Dome Tweeter

D2905/9700 1 Dome Tweeter

D3806/8200 1.5" Dome Mid/Tweeter

18W/8535 7" Carbon/Paper Woofer

4" Fiberglass Cone Midrange

4" Fiberglass Cone Midrange

5.25" Fiberglass Cone Mid

12W/4524G 4 4.5" Fiberglass Cone Woofer

12W/8524G 8 4.5" Fiberglass Cone Woofer

5.25" Fiberglass Cone Woofer

5.25" Fiberglass Cone Woofer

6.5" Fiberglass Cone Woofer

18W/8434G 8 6.5" Fiberglass Cone Woofer

8" Fiberglass Cone Woofer

8" Fiberglass Cone Woofer

10" Fiberglass Cone Woofer

10" Fiberglass Cone Woofer

10" Aluminum Subwoofer

12" Aluminum Subwoofer

P13WH00 8 5" Poly Cone Woofer

6.5" Poly Cone Woofer

8" Poly Cone Woofer

91 dB 28 Hz 5.7 ohm 0.9 mH 80W 235 cm2 40 mm 14 mm 6 mm

4mm 7.4 Tm 22.5 g - kg 113 liters 1.6 0.41 0.33 - mm/N

820012 Autosound 5" Car Component System

820013 Autosound 6" Car Component System

D 42.1 48.5 48.5 77 77 77 70 90 69 69 74 74 92 72 72 72 72 72 72 115.5 78 101 92 100

You might also like