SC9711

MCU EMBEDDED A/D CONVERTER FOR DMM(33/4 DIGITS)

DESCRIPTION
SC9711 is a 4000 counts digital multi-meter.

FEATURES
* ADC display three times pre second; * Auto Range Function Voltage(DC/AC): 400.0mV, 4.000V, 40.00V, 1000V Current(DC/AC): (400.0A,4000A), (40.00mA, 400.0mA), (10.00A) Resistor: 400.0 ,4.000k , 40.00k , 400.0k , 4.000M ,40.00M Diode and Continuity Measurement: Capacitance: 4.000nF, 40.00nF, 400.0nF, 4.000F, 40.00F, 200.0F(30Sec) Frequency: 9.999Hz, 99.99Hz, 999.9Hz, 9.999KHz, 99.99KHz, 999.9KHz, 9.999MHz Duty: 0.1%~99.9% * 3V battery operation * Low power consumption: Less than 6mW * Range Selection/Display Hold/Auto Power-Off/Relative * 1/3 bias, 1/4 duty LCD drive * 2.4V battery replacing caution detect * built-in AC/DC switch OPAMP * Built-in CMOS bandgap reference Device SC9711 SC9711X DIE Package QFP-100-14 x 20-0.65
QFP-100-14x20-0.65

ORDERING INFORMATIONS

APPLICATIONS
* Hand-held DMM * Pocket DMM * Pen-type DMM * Clamp Meter

BLOCK DIAGRAM

HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn

REV:1.1

2007.11.07 Page 1 of 14

SC9711
ELECTRICAL CHARACTERISTICS (Tamb=25C, VDD=3V)
Characteristics Recommend Operating Voltage Supply Current Power-off Current Digital Input High Voltage Digital Input Low Voltage Pull Up Current Analog Ground Voltage Analog Power Supply Voltage Build In Reference Voltage Reference Voltage Output Symbol VDD IDD IPO VIH VIL IPU AGND VDDA VBAND Relative AGND voltage VDD=2.4~3.6 REF1 VBATT FLCD VLCD FBEEP DC ADPx1 input=0V DC ADPx1 input Full Scale240.0mV AC ADPx1 240mVrms 20Hz~1KHz RCC O.L 10 4050 4000 360 VFREA VIL( relative AGND) VIH(relative AGND) VPP=100mV square wave input VPP=100mV square wave input VIL(relative AGND) VIH(relative AGND) VPP=600mV square wave input 5M -600 600 500k 1 -60 60 60 Ohm Counts Counts Counts mV mV Hz s mV mV Hz (To be continued) 0.2 % -0.001 -1 2.8 Relative to AGND voltage 2.25 Vin=0 VDD/2-3% 3.4 1.1 -2000 0.44 2.4 32 3 2.7 0.000 0 0.0001 +1 Counts 3.2 2.55 5 VDD/2 3.7 1.25 At DCV mode AT Power off VDD-0.5 0.5 10 VDD/2+3% 4 1.4 +2000 Test conditions Min. 2.4 1.5 Typ. Max. 3.6 2 10 Unit V mA A V V A V V V ppm/V V V Hz V KHz

Voltage Coefficient Recommend Input Reference Voltage Low Battery Detector Voltage LCD Frame Frequency LCD Pk-Pk Driver Voltage Beeper Frequency Zero Input Reading Linearity (max. Deviation From Best Straight Line Fit) AC Measurement Error Continuity Check Value ADC Measurement Display Count Autorange Up Counts Autorange Down Counts Frequency Counter Input Level (Hz/duty Control) Frequency Counter Max. Input Frequency (Hz/Duty Control) Duty Measurement Min. Pulse Width Error (Hz/duty Control) Frequency Counter Input Level (MEAS=0100) Frequency Counter Input Max. Frequency (MEAS=0100) Bandwidth

FMAXA *1 VFRED

FMAXD

HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn

REV:1.1

2007.11.07 Page 2 of 14

SC9711
(Continued) Characteristics Duty Measurement Min. Pulse Width Error (MEAS=0100) Symbol *1 Test conditions VPP=600mV square wave input 4.000nF Capacitor Measurement Accuracy After Zero Input Relative 400.0nF 40.00nF 400.0nF 4.000F 40.00F Min. Typ. Max. 100 5%+25 2%+10 0.5%+3 1%+2 1.5%+2 Unit ns Counts Counts Counts Counts Counts

FUNCTION AND RANGE TABLE

MEA4 MEA3 MEA2 MEA1 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 1 1 1 1 0 0 0 0 1 1 1 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 DCV ACV OHM Hz CAP Diode/ Beeper A V OHM/Diode/Beeper/CAP A mA Diode Beeper Hfe 400mV full scale input, no decimal, input through ADP (100/Amp, gain)(V/(C input, 1 1 1 1 Temp no decimal, input from ADP2. AC/DC switch AC/DC switch HZ/Duty/A HZ/Duty/A Diode/ Beeper switch AC/DC switch AC/DC switch HZ/Duty/A HZ/Duty/V HZ/Duty SELECT(1(0(1) Hz/Duty(1(0(1) Hz/Duty/V Hz/Duty/V

HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn

REV:1.1

2007.11.07 Page 3 of 14

SC9711

PIN CONFIGURATION
SEG10 SEG11 SEG12 SEG13 SEG14 COM1 XOUT VDDA RLCD SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9

VGG

TXD

N.C

N.C

N.C

N.C

N.C

80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51

N.C
50 49 48 47 46 45 44 43 42

XIN

CA

CB

VB

COM2 81 COM3 82 COM4 83 ENTX 84 BEEPER 85 BLOUT 86 RST 87 N.C 88 REFI 89 REFO 90 FTA 91 N.C 92 FTB 93 FTC 94 TSTC 95 OP1N 96 N.C 97 OP1O 98 N.C 99 OP2P
100

N.C N.C VDD N.C AGND N.C GND TSTA LCDC2 LCDC1 MEA1 MEA2 MEA3 MEA4 CAP Hz/DUTY HOLD REL RANGE SELECT

SC9711

41 40 39 38 37 36 35 34 33 32 31

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

OP2O

ADIP

SA

ADP

SMV

ONEK

TENK

HUNK

CRES1

RCAP1

RCAP2

CRES2

TESTB

RL

ADPC1

PIN DESCRIPTIONS
Pin no. 1 2 3 4 5 6 7 8 9 10 11 symbol OP2N NC OP2O AD1P NC AD1N NC SA SGND ADP DT Current measurement ADC connection Analog ground ADC negative input Additional ADC positive input Diode measurement resistor connection AC measurement negative input AC measure positive input AC measurement positive input Description AC measure negative input Pin no 51 52 53 54 55 56 57 58 59 60 61 symbol NC VB NC CB CA VGG NC VDDA RLCD NC XIN Oscillator input port (To be continued) Voltage stabilization output/ analog power LCD drive voltage regulate resistor Double connection Double voltage capacitor positive connection Double voltage output voltage capacitor Bias current input Description

HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn

REV:1.1

ADPC2

ONEM

SGND

TENM

OP2N

N.C

N.C

ADIN

N.C

N.C

N.C

N.C

N.C

N.C

DT

2007.11.07 Page 4 of 14

SC9711
(Continued) Pin no. 12 13 symbol NC High impedance voltage input/R SMV measurement ADC positive 63 NC input/diode resistor connection 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 CRES1 RL RCAP1 RCAP2 ONEK NC TENK NC HUNK NC ONEM NC TENM CRES2 TESTB ADPC1 ADPC2 SELECT RANGE REL HOLD Hz/DUTY CAP MEA4 MEA3 MEA2 MEA1 LCDC1 LCDC2 TSTA GND NC 10M resistor connection The capacitor of Resistor voltage Back light control pin No Use. No Use. Measure mode selected Auto/manual switch control Relative function Display Hold Hz/DUTY change No Use. Measure mode select 4 Measure mode select 3 Measure mode select 2 Measure mode select 1 No Use. No Use. Test pin 21.5V battery negative input 1.111M resistor connection 100.1k resistor 10.01k resistor connection R measurement filter capacitor connection Resistor reference voltage input No Use. No Use. 1.000k resistor 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 TXD NC SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 COM1 COM2 COM3 COM4 ENTX BEEPER BLOUT RST NC REFI REFO FTA NC FTB FTC TSTC ADC filter positive input pin ADC preceding filter negative port Test pin (To be continued) reference voltage input Bandgap output ADC filter positive output pin reference voltage LCD segment 14 LCD segment 13 LCD segment 12 LCD segment 11 LCD segment 10 LCD segment 9 LCD segment 8 LCD segment 7 LCD segment 6 LCD segment 5 LCD segment 4 LCD segment 3 LCD segment 2 LCD segment 1 Backplane 1 of LCD display Backplane 2 of LCD display Backplane 3 of LCD display Backplane 4 of LCD display no use Beeper output Back Light digital output CPU reset input Power control Description Pin no 62 symbol XOUT Description Oscillator output port

HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn

REV:1.1

2007.11.07 Page 5 of 14

SC9711
(Continued) Pin no. 46 47 48 49 50 symbol AGND NC VDD NC NC 21.5V battery positive input Description 3V battery midpoint, analogy ground. Pin no 96 97 98 99 100 symbol OP1N NC OP1O NC OP2P AC/Dc switcher OPAMP input pin AC signal buffer operate amplifier output pin AC Description signal buffer operate amplifier input pin (-)

FUNCTION DESCRIPTION
Auto/manual switch RANGE RANGE is the Push-Type switcher, and set in auto switch at power-on. If pressed RANGE key, it switch into manual step. In manual states, press it up jumper one step. If jumper from highest step to lowest step, only need pressed the key for 2 second, automatic switch into auto step. Hz/Duty and CAP because of the measure mode cannot switch into manual switch mode. Display hold HOLD HOLD Key is the Push-Type switcher, use for holding the display data. Relatively value display REL REL Key is the Push-Type switcher. Besides Hz/Duty, other measurements have this function, it can automatic switch into auto switch mode. Auto power-off When measure operating more than 15 minutes, and didn t switch the measure step (that is didn t press the push button), it will switch into standby mode automatically. If press the select key, auto power off invalidation. Back Light Control: When pressed the BLCTR or RANGE more than 2s, B1OUT will be set to 1 , and if press BLCTR again, it will be cleared. Beeper When select Rel Hold Range HZ/DUTY and BLCTR keys pressed and function switched , the Beeper On about 0.5~1S. When ACV>750V, DCV>1000V, AC/DCA >4000A, AC/DC mA, AC/DC A>10A, the beeper will hold ON to indicator the warning of the out of range. At one minute before auto power off, beeper will beep five times, and before shut down, beep one time.

HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn

REV:1.1

2007.11.07 Page 6 of 14

SC9711

CURRENT MEASUREMENT
Current measurement
900K I+ 10 Ohm 100K DT I10K SGND SA 400mA SMV 40mA

LCD DISPLAY
LCD display

LCD DISPLAY AND FORMAT

SCHEMATIC
Current measure 10 R10:R11=9:1 No No No No No No No No No AC measurement R23+VR3,R24=R25 No No No No No Yes Yes Yes Yes Reference Voltage R18, R19, VR1 Temperature Yes Yes Yes Yes Yes Yes Yes Yes Yes (To be continued)

Network DC 400mV DC 4V DC 40V DC 400V DC 1000V AC 400mV AC 4V AC 40V AC 400V No R5/(R4+R5)=1/10 R6/(R4+R6)=1/100 R7/(R4+R7)=1/1000 R8/(R4+R8)=1/10000 R5/(R4+R5)=1/10, R21:R22=9:1 R5/(R4+R5)=1/10 R6/(R4+R6)=1/100 R7/(R4+R7)=1/1000

HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn

REV:1.1

2007.11.07 Page 7 of 14

SC9711
(Continued) Network AC 1000V R 400 R 4k R 40k R 400k R 4M R 40M DC 400A DC 4000A DC 40mA DC 400mA DC 10A AC 400A AC 4000A AC 40mA AC 400mA AC 10A CAP Diode R8/(R4+R8)=1/10000 R4//R8=1k R4//R8=1k R4//R7=10k R4//R6=100k R4//R5=1M R4=10M R13+R14+R15=1k R13+R14+R15=1k R13+R14=10 R13+R14=10 R13=0.01 R13+R14+R15=1k R13+R14+R15=1k R13+R14=10 R13+R14=10 R13=0.01 R9+VR2 (R30+R31)/R31=10 Current measure 10 R10:R11=9:1 No No No No No No No No Yes No Yes No Yes No Yes No No No No AC measurement R23+VR3,R24=R25 Yes No No No No No No No No No No No Yes Yes Yes Yes Yes No No Reference Voltage R18, R19, VR1 Temperature Yes No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes

FUNCTION AND JUMPER SERRING

MEA4 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 MEA3 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 MEA2 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 MEA1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 DCV ACV OHM Hz CAP Diode/Beeper A V OHM/Diode/Beeper/CAP A mA Diode Beeper Hfe Temp Function Jumper J2 J2 J1, J3 J7, J8 J1, J3 J1, J3 J5, J6 J2 J1, J3 J6 J4, J6 J1, J3 J1, J3 J9 J10, J11 Input V/OHM/Diode, COM V/OHM/Diode, COM V/OHM/Diode, COM V/OHM/Diode, COM V/OHM/Diode, COM V/OHM/Diode, COM A/mA, COM V/OHM/Diode, COM V/OHM/Diode, COM 10A, COM A/mA, COM V/OHM/Diode, COM V/OHM/Diode, COM ADP (pin 10), COM ADP2 (pin 95), COM

HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn

REV:1.1

2007.11.07 Page 8 of 14

SC9711

LIST OF COMPONENT PARAMETER

PART TYPE 0.01 0.47F 0.47F 1.111M 100k 100k 100k 100k 100k 100k 101.0k 10k 10k 10k 10M 10nF 10F 10F 10F DESIGNATOR R15 C10 C11 R5 R11 R26 R27 R9 R3 R17 R6 R22 R7 R12 R4 C7 C14 C20 C19 PART TYPE 10F 10F 10F 1k 1k 1M 1M 1M 1N914 1N914 BUZZER 200k 20k 22k 22k 27nF 27nF 27nF 27nF 28.5k DESIGNATOR C14 C3 C4 R8 R28 R16 R30 R1 D1 D2 B1 R2 R19 R25 R24 C13 C6 C8 C12 R23 PART TYPE 4.7F 40k 40k 47nF 4MHz 500k 9.99 900K 90k 990 Key Key Key Key Key Key VR10k VR2k VR30k VR40k DESIGNATOR C9 R35 R18 C5 U2 R20 R14 R10 R21 R13 S6 S2 S1 S4 S3 S5 VR1 VR3 VR2 VR4

HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn

REV:1.1

2007.11.07 Page 9 of 14

SC9711

TYPICAL APPLICATION CIRCUIT

HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn

REV:1.1

2007.11.07 Page 10 of 14

SC9711

CHIP TOPOGRAPHY

Chip Size: 4.12 x 5.37 (mm2) Note: the substrate is connecting with VDD.

HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn

REV:1.1

2007.11.07 Page 11 of 14

SC9711

PAD CORRDINATES (Unit: m)

Pin no. 1 3 4 6 8 9 10 11 13 14 15 16 17 18 20 22 24 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 46 48 52 Symbol OP2N OP2O ADIP ADIN SA SGND ADP DT SMV CRES1 RL RCAP1 RCAP2 ONEK TENK HUNK ONEM TENM CRES2 TESTB ADPC1 ADPC2 SELECT RANGE REL Hz/HOLD DUTY CAP MEA4 MEA3 MEA2 MEA1 LCDC1 LCDC2 TSTA GND AGND VDD VB X 819.4 980.6 1141.8 1303 1464.2 1625.4 1786.6 1947.8 2109 2270.2 2431.4 2592.6 2753.8 2915 3076.2 3237.4 3398.6 3559.8 3721 3912.2 4162.2 4412.2 5037.4 5037.4 5037.4 5037.4 5037.4 5037.4 5037.4 5037.4 5037.4 5037.4 5037.4 5037.4 5037.4 5037.4 5037.4 5037.4 5037.4 Y 203.75 203.75 203.75 203.75 203.75 203.75 203.75 203.75 203.75 203.75 203.75 203.75 203.75 203.75 203.75 203.75 203.75 203.75 203.75 203.75 203.75 203.75 324.75 555.55 786.85 1018.15 1259.45 1448.7 1637.95 1827.2 2016.45 2205.7 2394.95 2584.2 2773.45 2963.2 3146.1 3335.85 3515.2 Pin no. 54 55 56 58 59 61 62 64 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 89 90 91 93 94 95 96 98 100 Symbol CB CA VGG VDDA RLCD XIN XOUT TXD SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 COM1 COM2 COM3 COM4 ENTX BEEPER BLOUT RST REFI REFO FTA FTB FTC TSTC OP1N OP1O OP2P X 4432.95 4239.75 4083.55 3837.65 3696.75 3425.75 3274.35 3113.45 2667.05 2521.15 2375.25 2229.35 2083.45 1937.55 1791.65 1645.75 1499.85 1353.95 1208.05 1062.15 916.25 770.35 203.8 203.8 203.8 203.8 203.8 203.8 203.8 203.8 203.8 203.8 203.8 203.8 203.8 203.8 203.8 203.8 203.8 Y 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3790.65 3216.25 3070.35 2924.45 2778.55 2623.85 2453.85 2302.65 2156.25 1867.65 1706.45 1545.25 1384.05 1222.85 1061.65 900.45 739.25 578.05

Note: the original point of the coordinate is the die center.

HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn

REV:1.1

2007.11.07 Page 12 of 14

SC9711

PACKAGE OUTLINE
QFP-100-14x20-0.65 Unit: mm

HANDLING MOS DEVICES:

Electrostatic charges can exist in many things. All of our MOS devices are internally protected against electrostatic discharge but they can be damaged if the following precautions are not taken: Persons at a work bench should be earthed via a wrist strap. Equipment cases should be earthed. All tools used during assembly, including soldering tools and solder baths, must be earthed. MOS devices should be packed for dispatch in antistatic/conductive containers.

HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn

REV:1.1

2007.11.07 Page 13 of 14

SC9711

ATTACHMENT Revision History

Data 2004.08.04 2007.11.07 REV 1.0 1.1 Original Modify the FUNCTION AND JUMPER SERRING Description Page

HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn

REV:1.1

2007.11.07 Page 14 of 14