Ecs 945GCT-M2 - 1333

i
Preface
Copyright
This publication, including all photographs, illustrations and software, is protected
under international copyright laws, with all rights reserved. Neither this manual, nor
any of the material contained herein, may be reproduced without written consent of
the author.
Version 1.0A
Disclaimer
The information in this document is subject to change without notice. The manufac-
turer makes no representations or warranties with respect to the contents hereof and
specifically disclaims any implied warranties of merchantability or fitness for any
particular purpose. The manufacturer reserves the right to revise this publication and
to make changes from time to time in the content hereof without obligation of the
manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel
Corporation.
Other product names used in this manual are the properties of their respective
owners and are acknowledged.
Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment onto an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with
this equipment to ensure compliance with the pertinent RF emission limits govern-
ing this device. Changes or modifications not expressly approved by the system’s
manufacturer could void the user’s authority to operate the equipment.
Preface
ii
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the
following conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interfer-
ence that may cause undesired operation
Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-
causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur
le matériel brouilieur du Canada.
About the Manual

The manual consists of the following:
Chapter 1 Describes features of the motherboard.

Introducing the Motherboard Go to H page 1
Chapter 2 Describes installation of motherboard

components.
Installing the Motherboard
Go to H page 7
Chapter 3 Provides information on using the BIOS

Setup Utility.
Using BIOS
Go to H page 27
Chapter 4 Describes the motherboard software

Using the Motherboard Soft- Go to H page 43
ware
Preface
iii
TABLE OF CONTENTS
Preface i
Chapter 1 1
Introducing the Motherboard 1
Introduction...............................................................................................1
Feature........................................................................................................2
Motherboard Components......................................................................4
Chapter 2 7
Installing the Motherboard 7
Safety Precautions ................................................................................7
Choosing a Computer Case....................................................................7
Installing the Motherboard in a Case...................................................7
Checking Jumper Settings......................................................................8
Setting Jumpers...................................................................................8
Checking Jumper Settings...................................................................9
Jumper Settings...................................................................................9
Installing Hardware..............................................................................10
Installing the Processor....................................................................10
Installing Memory Modules..............................................................12
Expansion Slots................................................................................16
Connecting Optional Devices...........................................................18
Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive..............21
Installing a Floppy Diskette Drive....................................................22
Connecting I/O Devices......................................................................23
Connecting Case Components...........................................................24
Front Panel Header..........................................................................26
Chapter 3 27
Using BIOS 27
About the Setup Utility...................................................................... 27
The Standard Configuration.............................................................27
Entering the Setup Utility..................................................................27
Using BIOS...........................................................................................28
Standard CMOS Setup......................................................................29
Advanced Setup.................................................................................30
Advanced Chipset Setup....................................................................32
iv
Integrated Peripherals.......................................................................33
Power Management Setup..................................................................34
PCI/PnP Setup....................................................................................35
PC Health Status................................................................................36
Frequency/Voltage Control.................................................................37
Load Optimal Defaults......................................................................38
Supervisor Password.........................................................................38
User Password...................................................................................39
Save & Exit Setup..............................................................................40
Exit Without Saving............................................................................40
Updating the BIOS............................................................................41
Chapter 4 43
Using the Motherboard Software 43
About the Software CD-ROM............................................................43
Auto-installing under Windows 2000/XP.........................................43
Running Setup....................................................................................44
Manual Installation..............................................................................46
Utility Software Reference..................................................................46
1
Chapter 1
Introducing the Motherboard
Introduction
Thank you for choosing the 945GCT-M2/1333 motherboard. This motherboard is a
high performance, enhanced function motherboard designed to support the LGA775
socket Intel CoreTM 2 Duo/*Pentium D/*Pentium 4/Celeron D processors for high-
end business or personal desktop markets.
The motherboard incorporates the 945GC Northbridge (NB) and ICH7 Southbridge
(SB) chipsets. The Northbridge supports a Front Side Bus (FSB) frequency of 1333/
1066/800/533 MHz using a scalable FSB Vcc_CPU. The memory controller supports
DDR2 memory DIMM frequencies of 667/533/400. It supports two DDR2 Sockets
with up to maximum memory of 2 GB DDR2 Maximum memory bandwidth of 10.7
GB/s in dual-channel interleaved mode assuming DDR2 667 MHz. High resolution
graphics via one PCI Express slot, intended for Graphics Interface, is fully compliant
to the PCI Express Base Specification revision 1.0a.
* Under ECS validation, this motherboard is capable to support FSB 1333 MHz.
The ICH7 Southbridge supports two PCI slots which are PCI v2.3 compliant. It
implements an EHCI compliant interface that provides 480 Mb/s bandwidth for
eight USB 2.0 ports (four USB ports and two USB 2.0 headers support additional four
USB ports). One onboard IDE connector supports 2 IDE devices in Ultra ATA 100/
66/33 mode. The Southbridge integrates a Serial ATA host controller, supporting four
SATA ports with maximum transfer rate up to 3.0 Gb/s each.
The motherboard is equipped with advanced full set of I/O ports in the rear panel,
including PS/2 mouse and keyboard connectors, COM1, one VGA port, four USB
ports, one LAN port and audio jacks for microphone, line-in and line-out.
“*” stands for this motherboard is ready to support Pentium D/ Pentium 4

processors.

2
Feature
Processor
The motherboard uses an LGA775 type of Intel Core TM 2 Duo/*Pentium D/
*Pentium 4/Celeron D that carries the following features:
• Accommodates Intel CoreTM 2 Duo/*Pentium D/*Pentium 4/Celeron D pro-
cessors
• Supports a system bus (FSB) of 1333/1066/800/533 MHz
• Supports “Hyper-Threading” technology CPU
* Supports 05A, 06 FMB CPU
* This motherboard is ready to support Pentium D/ Pentium 4 processors
“Hyper-Threading” technology enables the operating system into thinking it’s
hooked up to two processors, allowing two threads to be run in parallel, both on
separate “logical” processors within the same physical processor.
Chipset
The 945GC Northbridge (NB) and ICH7 Southbridge (SB) chipsets are based on an
innovative and scalable architecture with proven reliability and performance.
945GC (NB) • Supports 32-bit host bus addressing, allowing the CPU to
access the entire 2 GB of the memory address space.
• 2 GB/s point-to-point Direct Media Interface (DMI) to ICH7 (1
GB/s)each direction.
• Supports 256-Mb, 512-Mb and 1-Gb DDR2 technologies for
x8 and x16 devices
• Supports high quality 3D setup, Render Engine and high-
quality texture engine
ICH7 (SB) • Enhanced DMA Controller, interrupt controller, and timer func-
tions
• Compliant with PCI Express Base Specification, Revision
1.0a
• Compliant with PCI 2.3 specification
• Integrated SATA 3.0 Gb/s Host Controller
• Integrated USB 2.0 Host Controller supporting up to eight
USB 2.0 ports
• Integrated IDE controller supports Ultra ATA 100/66/33
Memory
• Supports DDR2 667/533/400 DDR SDRAM with Dual-channel architec-
ture
• Accommodates two unbuffered DIMMs
• Up to 1 GB per DIMM with maximum memory size up to 2 GB
Audio
• 5.1 Channel High Definition Audio Codec
• All DACs support 192K/96K/48K/44.1KHz sample rate
• Software selectable 2.5V/3.75V VREFOUT
• Meets Microsoft WHQL/WLP 2.x audio requirements
• Direct Sound 3DTM compatible
3
Onboard LAN (Optional)

The onboard LAN controller provides the following features:
• Integrated 10/100/1000 transceiver

• Supports PCI v2.3, 32-bit, 33/66 MHz
• Supports Wake-On-LAN (WOL) function and remote wake-up
• Supports 10/100 Mb/s N-Way Auto negotiation operation

• Half/Full duplex capacity
• Supports Wake-On-LAN (WOL) function and remote wake-up
Expansion Options
The motherboard comes with the following expansion options:
• One PCI Express Slot for Graphic Interface
• Two 32-bit PCI v2.3 compliant slots
• One 40-pin IDE connector that support two IDE devices
• One floppy disk drive interface
• Four 7-pin SATA connectors
The motherboard supports UDMA bus mastering with transfer rates of 100/66/33
Mb/s.
Integrated I/O
The motherboard has a full set of I/O ports and connectors:
• Two PS/2 ports for mouse and keyboard
• One serial port
• One VGA port
• Four USB ports
• One LAN port
• Audio jacks for microphone, line-in and line-out
BIOS Firmware
This motherboard uses AMI BIOS that enables users to configure many system
features including the following:
• Power management
• Wake-up alarms
• CPU parameters
• CPU and memory timing
The firmware can also be used to set parameters for different processor clock
speeds.
1.Some hardware specifications and software items are subject to change

without prior notice.
2.Due to chipset limitation, we recommend that motherboard be oper-
ated in the ambiance between 0 and 50° C.

4
Motherboard Components

5
Table of Motherboard Components
LABEL COMPONENTS
LGA775 Socket for Intel® CoreTM 2 Duo/
1. CPU Socket
*Pentium® D/ *Pentium® 4/ Celeron® D CPUs
2. CPU_FAN CPU cooling fan connector
3. DIMM1/2 240-pin DDR2 SDRAM slots
4. ATX1 Standard 24-Pin ATX Power connector
5. SATA1~4 Serial ATA connectors
6. F_USB1~2 Front Panel USB headers
7. SPK1 Speaker header
8. USBPWR_F Front Panel USB Power Select Jumper
9. F_PANEL1 Front panel switch/LED header
10. IDE1 Primary IDE connector
11. CLR_CMOS Clear CMOS jumper
12. FDD Floppy Disk Drive connector
13. SPDIFO1 SPDIF out header
14. CD_IN1 Analog audio input connector
15. F_AUDIO1 Front Panel Audio header
16. PCI1~2 32-bit add-on card slots
17. PCIEX16 PCI Express slot for graphics interface
18. USBPWR_R Rear Panel USB PS/2 Power Select Jumper
19. SYS_FAN System Fan connector
20. ATX12V1 4-pin +12V power connector
21. LPT1 Parallel port header
“*” stands for this motherboard is ready to support Pentium D/Pentium 4

processors.
This concludes Chapter 1. The next chapter explains how to install the motherboard.

6
Memo

7
Chapter 2
Safety Precautions
• Follow these safety precautions when installing the motherboard
• Wear a grounding strap attached to a grounded device to avoid dam-
age from static electricity
• Discharge static electricity by touching the metal case of a safely
grounded object before working on the motherboard
• Leave components in the static-proof bags they came in
• Hold all circuit boards by the edges. Do not bend circuit boards
Choosing a Computer Case

There are many types of computer cases on the market. The motherboard complies
with the specifications for the Micro ATX system case. First, some features on the
motherboard are implemented by cabling connectors on the motherboard to indica-
tors and switches on the system case. Make sure that your case supports all the
features required. Secondly, this motherboard supports one floppy diskette drive and
two enhanced IDE drives. Make sure that your case has sufficient power and space for
all drives that you intend to install.
Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O
template in the case matches the I/O ports installed on the rear edge of the
motherboard.
This motherboard carries a Micro ATX form factor of 244 x 200 mm. Choose a case
that accommodates this form factor.
Installing the Motherboard in a Case

Refer to the following illustration and instructions for installing the motherboard in
a case.
Most system cases have mounting brackets installed in the case, which correspond
the holes in the motherboard. Place the motherboard over the mounting brackets
and secure the motherboard onto the mounting brackets with screws.
Ensure that your case has an I/O template that supports the I/O ports and expansion
slots on your motherboard.

8
Do not over-tighten the screws as this can stress the motherboard.
Checking Jumper Settings

This section explains how to set jumpers for correct configuration of the motherboard.
Setting Jumpers
Use the motherboard jumpers to set system configuration options. Jumpers with
more than one pin are numbered. When setting the jumpers, ensure that the jumper
caps are placed on the correct pins.
The illustrations show a 2-pin jumper. When

the jumper cap is placed on both pins, the
jumper is SHORT. If you remove the jumper
cap, or place the jumper cap on just one pin,
the jumper is OPEN. SHORT OPEN
This illustration shows a 3-pin jumper. Pins

1 and 2 are SHORT.

9
Checking Jumper Settings

The following illustration shows the location of the motherboard jumpers. Pin 1 is
labeled.
Jumper Settings
Jumper Type Description Setting (default)
1-2: NORMAL
2-3: CLEAR CMOS
CLR_CMOS 3-pin Clear CMOS
Before clearing the 1
CMOS, make sure to
CLR_CMOS
turn off the system.
Front Panel 1-2: VCC 1
USBPWR_F 3-pin USB Power
Select Jumper
2-3: 5VSB USBPWR_F
Rear USB PS/2 1
USBPWR_R 3-pin Power Select 1-2: VCC
Jumper 2-3: 5VSB
USBPWR_R
1. To avoid the system unstability after clearing CMOS, we recommend

users to enter the main BIOS setting page to “Load Optimal Defaults”
and then “Save Changes and Exit”.
2. Make sure the power supply provides enough 5VSB voltage before
selecting the 5VSB function.
3. It is required that users place the USBPWR_F & USBPWR_R cap onto
2-3 pin rather than 1-2 pin as default if you want to wake up the com-
puter by USB/PS2 KB/Mouse.
10
Installing Hardware
Installing the Processor
Caution: When installing a CPU heatsink and cooling fan make sure
that you DO NOT scratch the motherboard or any of the surface-mount
resistors with the clip of the cooling fan. If the clip of the cooling fan
scrapes across the motherboard, you may cause serious damage to the
motherboard or its components.
On most motherboards, there are small surface-mount resistors near
the processor socket, which may be damaged if the cooling fan is care-
lessly installed.
Avoid using cooling fans with sharp edges on the fan casing and the
clips. Also, install the cooling fan in a well-lit work area so that you can
clearly see the motherboard and processor socket.
Before installing the Processor

This motherboard has a LGA775 socket. When choosing a processor, consider the
performance requirements of the system. Performance is based on the processor
design, the clock speed and system bus frequency of the processor, and the quantity
of internal cache memory and external cache memory.
This motherboard automatically determines the CPU clock frequency and system
bus frequency for the processor. You may be able to change the settings in the system
Setup Utility. We strongly recommend that you do not over-clock processors or
other components to run faster than their rated speed.
Warning:
1. Over-clocking components can adversely affect the reliability of the
system and introduce errors into your system. Over-clocking can per-
manently damage the motherboard by generating excess heat in com-
ponents that are run beyond the rated limits.
2. Always remove the AC power by unplugging the power cord from the
power outlet before installing or removing the motherboard or other
hardware components.
Fail-Safe Procedures for Over-clocking

When end-users encounter failure after attempting over-clocking, please take the
following steps to recover from it.
1. Shut down the computer.
2. Press and hold the “Page Up Key (PgUp)” of the keyboard, and then boot the
PC up.
3. Two seconds after the PC boots up, release the “Page Up Key (PgUp)”.
4. System will stop on POST screen and show CMOS setting wrong. Press F1 enter
Setup and load default setting again.

11
CPU Installation Procedure

The following illustration shows CPU installation components.
A. Read and follow the instructions shown on the

sticker on the CPU cap.
B. Unload the cap
· Use thumb & forefinger to hold the
lifting tab of the cap.
· Lift the cap up and remove the cap
completely from the socket.
C. Open the load plate

· Use thumb & forefinger to hold the
hook of the lever, pushing down and pulling
aside unlock it.
· Lift up the lever.
· Use thumb to open the load plate. Be
careful not to touch the contacts.
D. Install the CPU on the socket

· Orientate CPU package to the socket.
Make sure you match triangle marker
to pin 1 location.
E. Close the load plate

· Slightly push down the load plate onto the
tongue side, and hook the lever.
· CPU is locked completely.
F. Apply thermal grease on top of the CPU.
G. Fasten the cooling fan supporting base onto

the CPU socket on the motherboard.
H. Make sure the CPU fan is plugged to the

CPU fan connector. Please refer to the CPU
cooling fan user’s manual for more detail
installation procedure.
1. To achieve better airflow rates and heat dissipation, we suggest that you
use a high quality fan with 3800 rpm at least. CPU fan and heatsink
installation procedures may vary with the type of CPU fan/heatsink sup
plied. The form and size of fan/heatsink may also vary.
2. DO NOT remove the CPU cap from the socket before installing a CPU.
3. Return Material Authorization (RMA) requests will be accepted only if the
motherboard comes with the cap on the LGA775 socket.

12
Installing Memory Modules

This motherboard accommodates two memory modules. It can support two 240-pin
DDR2 667/533/400. The total memory capacity is 2 GB.
DDR2 SDRAM memory module table

Memory module Memory Bus
DDR2 400 200 MHz
DDR2 533 266 MHz
DDR2 667 333 MHz
You must install at least one module in any of the two slots. Each module can be
installed with 256 MB to 1 GB of memory; total memory capacity is 2 GB.
Do not remove any memory module from its antistatic packaging until
you are ready to install it on the motherboard. Handle the modules only
by their edges. Do not touch the components or metal parts. Always
wear a grounding strap when you handle the modules.
Installation Procedure
Refer to the following to install the memory modules.
1 This motherboard supports unbuffered DDR2 SDRAM .
2 Push the latches on each side of the DIMM slot down.
3 Align the memory module with the slot. The DIMM slots are keyed with
notches and the DIMMs are keyed with cutouts so that they can only be
installed correctly.
4 Check that the cutouts on the DIMM module edge connector match the
notches in the DIMM slot.
5 Install the DIMM module into the slot and press it firmly down until it
seats correctly. The slot latches are levered upwards and latch on to
the edges of the DIMM.
6 Install any remaining DIMM modules.

13
Please check the table below for the CPU FSB frequency and its corresponding
memory support frequency.
CPU FSB Frequency Memory Support Frequency

1333 DDRII533, DDRII667*
1066 DDRII533, DDRII667
800 DDRII400, DDRII533, DDRII667
533 DDRII400, DDRII533
*When you use a FSB1333-CPU on this motherboard, it will run at DDRII500 if you
adopt a DDRII533 memory module; and it will run at DDRII500 if “DRAM
Frequency” in “ F requency/Voltage Control” of BIOS is selected to “Auto”, while it
will run at DDRII667 when selected to “667MHZ” .
Table A: DDR2(memory module) QVL (Qualified Vendor List)
The following DDR2 667/533/400 memory modules have been tested and qualified
for use with this motherboard.
Type Size Vendor Module Nam e
HYMP532U646-E3 AA
256 MB Hynix
DDRII 400 NT256T64UH4A0F-5A
512 MB Nanya NT512T64U88A0F-5A
A-DATA M2OHY2F3G3110A1B0Z
Elixir M2U25664TUH4A0F-37B
Infineon HYS64T32400HU-3.7-A
256 MB ELPIDA E5116AF-5C-E
Kingston
HYB18T512160AC-3.7
Ramaxel RML 1040M28D5F-533
Samsung M378T3253FGO-CD5
AET660UD00-370A98U
Aeneon AET660UD00-370A98X
AET660UD00-370A98Z
DDRII 533
512 MB
ELPIDA E5108AB-5C-E
Kingston
HYB18T512800AF37
PQI MEABR321LA01AA
Samsung M378T6553BGO-CD5
Apacer ELPIDA E5108AB-5C-E
1 GB Kingston NANYA NT5TU64M8AE-37B
PQI MEABR421LA0106
UMAX UMAX U2S12D30TP-5C

14

Infineon HYS64T325001HU-3-A
256 MB
Ramxel 5NB31 D9DCG
AD29608A88-3EG
A-DATA
Eipida M20EL5G3H3160B100Z
Corsair K4T5108QC
Corsair VALUESELECT 32M8CEC
64M8CFE PS1000545
GL2L64M088BA18W
GEIL
GL2L64M088BA30AW
Infinity 0547W64M8 PC5300
512 MB
Ramxel 5LB31 D9DCL
DDRII 667
K4T51083QC
Samsung
PC35300U-25331-Z
Sync MAX 04400WB01 R050008A
JetRam J12Q3AB-6
Transcend SEL520ZCE6 K4T51083QC
TAIWAN-G6E
Tw inmos TMM6208G8M30B
AM4B5708GQJS7E0631F
Apacer
Elpida AM4B5708GQJS7E0631
1 GB
Infineon HYB18T512800BF3S
PQI PQB2648D38R0648

15
Table B: DDR2(memory module) QVL (Qualified Vendor List)

The following DDR2 667/533 memory modules have been tested and qualified for
use when you use a FSB 1333-CPU on this motherboard.
Corsair VC256MB533D2 4PB11D9CHM
Elpida Japan E2508AA-T7F-E
Kingmax Hynix HY5PS121621
256 MB Nanya NT5TU32M16AG-37B
5PB42 D9DCD
Ramaxel
Elpida D5116AF-5C-E
Tw inmos Elpida 8D22IB-ED
AET94F370
Aeneon
AET93F370
Samsung K4T51083QB-ZCD5
Corsair
VS512MB533D2 64M8CEC
Elpida 04180WB01
Hynix HY5PS12821
Infineon HY818T512800AF37 33346778
DDRII 533
Hynix HYB18T512800AF37
512 MB
Kingston Hynix HY5PS12821
Nanya NT5TU64M8AE-37B
5PB32 D9DCN
Ramaxel Elpida E5108AG-5C-E
6AD11 D9GCT
Samsung PC2-4200U-4444-10-B1 K4T51083QF-ZCD5
Elpida E5108AB-5C-E
Tw inmos
Samsung 8D22JB-KM
Apacer Eipida E5108AB-5C-E
Geil A016E2864T2AG8AKT5H120001
1GB Infineon HY818T512800AF37 33344539
Kingmax KKEA88E4AAKG-37
PQI PQI PQB2648D38R0651
256 MB Infineon HYS64T325001HU-3-A HYB18T256
APOGEE AU51082-667P005
64M8CFE PS1000545
Corsair
VALUESELECT 32M8CEC
GEIL GL2L64M088BA18W
Infinity 0547W64M8 PC5300
512 MB PSC AL6E8E63B-6E1T
Ramxel 5LB31 D9DCL
DDRII 667
Samsung K4T51083QC
Sync MAX 04400WB01 R050008A
Transcend JetRam J12Q3AB-6
Tw inmos TMM6208G8M30B
APOGEE AU51082-667P005
Infineon Aeneon AET93E30RB-0650
1 GB
PQI PQI PQB2648D38R0648
PSC AL6E8E63B-6E1T

16
Expansion Slots
Installing Add-on Cards
The slots on this motherboard are designed to hold expansion cards and connect
them to the system bus. Expansion slots are a means of adding or enhancing the
motherboard’s features and capabilities. With these efficient facilities, you can
increase the motherboard’s capabilities by adding hardware that performs tasks that
are not part of the basic system.
PCIEX16 The PCI Express slot is used to install an external PCI Express graphics
Slot card that is fully compliant to the PCI Express Base Specification revi-
sion 1.0a.
PCI 1~2 This motherboard is equipped with two standard PCI slots. PCI stands
Slots for Peripheral Component Interconnect and is a bus standard for expan-
sion cards, which for the most part, is a supplement of the older ISA bus
standard. The PCI slots on this board are PCI v2.3 compliant.
1. Before installing an add-on card, check the documentation for the

card carefully. If the card is not Plug and Play, you may have to manu-
ally configure the card before installation.
2. FSB1333-CPU will operate in overclocking mode. Under this situa-
tion, PCIE frequency will also be overclocked from 100MHz to 125MHz.

17
Follow these instructions to install an add-on card:

1 Remove a blanking plate from the system case corresponding to the
slot you are going to use.
2 Install the edge connector of the add-on card into the expansion slot.
Ensure that the edge connector is correctly seated in the slot.
3 Secure the metal bracket of the card to the system case with a screw.
1. For some add-on cards, for example graphics adapters and network adapt-
ers, you have to install drivers and software before you can begin using the
add-on card.
2. The onboard PCI interface does not support 64-bit SCSI cards.

18
Connecting Optional Devices

Refer to the following for information on connecting the motherboard’s optional
devices:
F_AUDIO1: Front Panel Audio header for Azalia

This header allows the user to install auxiliary front-oriented microphone and line-
out ports for easier access.
Pin Signal Name Function

Pin Signal Name
1 AUD_MIC Front Panel Microphone input signal
2 AUD_GND Ground used by Analog Audio Circuits
3 MIC_BIAS Microphone Power
4 AUD_VCC Filtered +5V used by Analog Audio Circuits
5 AUD_F_R Right Channel audio signal to Front Panel
6 AUD_RET_R RightChannelAudiosignaltoReturnfromFrontPanel
7 REVD Reserved
8 Key No Pin
9 AUD_F_L Left Channel Audio signal to Front Panel
10 AUD_RET_L Left Channel Audio signal to Return from Front Panel

19
SATA1~4: Serial ATA connectors

These connectors are used to support the new Serial ATA devices for the highest data
transfer rates (3.0 Gb/s), simpler disk drive cabling and easier PC assembly. It elimi-
nates limitations of the current Parallel ATA interface. But maintains register com-
patibility and software compatibility with Parallel ATA.
Pin Signal Name Pin Signal Name

1 Ground 2 TX+
3 TX- 4 Ground
5 RX- 6 RX+
7 Ground - -
CD_IN1: Analog Audio Input connector

1 CD_L CD In right channel
2 GND Ground
3 GND Ground
4 CD_R CD In left channel
F_USB1~2: Front Panel USB headers

The motherboard has four USB ports installed on the rear edge I/O port array.
Additionally, some computer cases have USB ports at the front of the case. If you
have this kind of case, use auxiliary USB connector to connect the front-mounted
ports to the motherboard.

1 USBPWR Front Panel USB Power
2 USBPWR Front Panel USB Power
3 USB_FP_P0- USB Port 0 Negative Signal
4 USB_FP_P1- USB Port 1 Negative Signal
5 USB_FP_P0+ USB Port 0 Positive Signal
6 USB_FP_P1+ USB Port 1 Positive Signal
7 GND Ground
8 GND Ground
9 Key No pin
10 USB_FP_OC0 Overcurrent signal
Please make sure that the USB cable has the same pin assignment as
indicated above. A different pin assignment may cause damage or system
hang-up.

20
SPDIFO1: SPDIF out header

This is an optional header that provides an SPDIFO (Sony/Philips Digital Interface)
output to digital multimedia device through optical fiber or coaxial connector.
Pin Signal Name

1 SPDIFOUT
2 +5V
3 Key
4 GND

21
Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive

This section describes how to install IDE devices such as a hard disk drive and a CD-
ROM drive.
About IDE Devices

Your motherboard has one IDE channel interface. An IDE ribbon cable supporting
two IDE devices is bundled with the motherboard.
You must orient the cable connector so that the pin1 (color) edge of the
cable corresponds to the pin 1 of the I/O port connector.
IDE1: IDE Connector

This motherboard supports four high data transfer SATA ports with each runs up
to 3.0 Gb/s. To get better system performance, we recommend users connect the
CD-ROM to the IDE channel, and set up the hard dives on the SATA ports.
IDE devices enclose jumpers or switches used to set the IDE device as MASTER or
SLAVE. Refer to the IDE device user’s manual. Installing two IDE devices on one
cable, ensure that one device is set to MASTER and the other device is set to SLAVE.
The documentation of your IDE device explains how to do this.
About SATA Connectors

Your motherboard features four SATA connectors supporting a total of four drives.
SATA refers to Serial ATA (Advanced Technology Attachment) is the standard inter-
face for the IDE hard drives which are currently used in most PCs. These connectors
are well designed and will only fit in one orientation. Locate the SATA connectors on
the motherboard and follow the illustration below to install the SATA hard drives.
Installing Serial ATA Hard Drives

To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the
Serial ATA protocol. This SATA cable comes with a SATA power cable. You can
connect either end of the SATA cable to the SATA hard drive or the connector on the
SATA cable (optional) SATA power cable (optional)

22
Refer to the illustration below for proper installation:
1 Attach either cable end to the connector on the motherboard.

2 Attach the other cable end to the SATA hard drive.
3 Attach the SATA power cable to the SATA hard drive and connect the
other end to the power supply.
This motherboard does not support the “Hot-Plug” function.
Installing a Floppy Diskette Drive

FDD: Floppy Disk Connector
Connect the single end of the of the floppy connector to the onboard floppy
connector firstly, and then connect the remaining plugs on the other end to the
floppy drives correspondingly.
You must orient the cable connector so that the pin 1 (color) edge of
the cable corresponds to the pin 1 of the I/O port connector.

23
Connecting I/O Devices

The backplane of the motherboard has the following I/O ports:
PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device.
PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard.
Serial Port (COM1) Use the COM port to connect serial devices such as mice or
fax/modems.
VGA Port Connect your monitor to the VGA port.
LAN Port Connect an RJ-45 jack to the LAN port to connect your
computer to the Network.
USB Ports Use the USB ports to connect USB devices.
Audio Ports Use the three audio ports to connect audio devices. The first
jack is for stereo line-in signal. The second jack is for stereo
line-out signal. The third jack is for microphone.
This motherboard may adopt 8-channel audio ports that

correspond to the A, B, C, and E port respectively. In addi-
tion, all of the 3 ports, B, C, and E provide users with both
right & left channels individually. Users please refer to the
following note for specific port function definition.
A: Center & Woofer D: Line-in

B: Back Surround E: Front Out
C: Side Surround F: Mic_in Rear
The above port definition can be changed to audio input or
audio output by changing the driver utility setting.

24
Connecting Case Components

After you have installed the motherboard into a case, you can begin connecting the
motherboard components. Refer to the following:
1 Connect the CPU cooling fan cable to CPU_FAN.
2 Connect the system cooling fan connector to SYS_FAN.
3 Connect the case switches and indicator LEDs to the F_PANEL1.
4 Connect the standard power supply connector to ATX1.
5 Connect the auxiliary case power supply connector to ATX12V1.
6 Connect the case speaker cable to SPK1.
Connecting 24-pin power cable

The ATX1 24-pin connector allows you to connect to ATX v2.x power
supply.
With ATX v2.x power supply, users please

note that when installing 24-pin power
cable, the latches of power cable and the
ATX1 match perfectly.
24-pin power cable
Connecting 4-pin power cable

The ATX12V1 power connector is used to provide power to the CPU.
When installing 4-pin power cable, the

latches of power cable and the ATX12V1
match perfectly.
4-pin power cable

25
CPU_FAN: FAN Power Connector

1 GND System Ground
2 +12V Power +12V
3 Sense Sensor
4 PWM CPU FAN control
Users please note that the fan connector supports the CPU cooling fan of
1.1A ~ 2.2A (26.4W max) at +12V.
SYS_FAN: FAN Power Connector

1 GND System Ground
2 +12V Power +12V
3 Sense Sensor
ATX1: ATX 24-pin Power Connector

Pin Signal Name Pin Signal Name
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 Ground 15 Ground
4 +5V 16 PS_ON
5 Ground 17 Ground
6 +5V 18 Ground
7 Ground 19 Ground
8 PWRGD 20 -5V
9 +5VSB 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 +3.3V 24 Ground
ATX12V1: ATX 12V Power Connector
Pin Signal Name

1 Ground
2 Ground
3 +12V
4 +12V
SPK1: Internal speaker

Pin Signal Name
1 VCC
2 Key
3 NC
4 Signal

26
Front Panel Header

The front panel header (F_PANEL1) provides a standard set of switch and LED
headers commonly found on ATX or Micro ATX cases. Refer to the table below for
information:
Pin Signal Function Pin Signal Function

1 HD_LED_P Hard disk LED(+) 2 FP PWR/SLP *MSG LED(+)
3 HD_LED_N Hard disk LED(- ) 4 FP PWR/SLP *MSG LED(-)
5 RST_SW_N Reset Switch(-) 6 PWR_SW_P Power Switch(+)
7 RST_SW_P Reset Switch(+) 8 PWR_SW_N Power Switch(-)
9 RSVD Reserved 10 Key No pin
* MSG LED (dual color or single color)
Hard Drive Activity LED
Connecting pins 1 and 3 to a front panel mounted LED provides visual indication
that data is being read from or written to the hard drive. For the LED to function
properly, an IDE drive should be connected to the onboard IDE interface. The LED
will also show activity for devices connected to the SCSI (hard drive activity LED)
connector.
Power/Sleep/Message waiting LED
Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides
power on/off, sleep, and message waiting indication.
Reset Switch
Supporting the reset function requires connecting pins 5 and 7 to a momentary-
contact switch that is normally open. When the switch is closed, the board resets and
runs POST.
Power Switch
Supporting the power on/off function requires connecting pins 6 and 8 to a momen-
tary-contact switch that is normally open. The switch should maintain contact for at
least 50 ms to signal the power supply to switch on or off. The time requirement is
due to internal de-bounce circuitry. After receiving a power on/off signal, at least two
seconds elapses before the power supply recognizes another on/off signal.
This concludes Chapter 2. The next chapter covers the BIOS.

27
Chapter 3
Using BIOS
About the Setup Utility

The computer uses the latest “American Megatrends Inc. ” BIOS with support for
Windows Plug and Play. The CMOS chip on the motherboard contains the ROM
setup instructions for configuring the motherboard BIOS.
The BIOS (Basic Input and Output System) Setup Utility displays the system’s
configuration status and provides you with options to set system parameters. The
parameters are stored in battery-backed-up CMOS RAM that saves this information
when the power is turned off. When the system is turned back on, the system is
configured with the values you stored in CMOS.
The BIOS Setup Utility enables you to configure:
• Hard drives, diskette drives and peripherals

• Video display type and display options
• Password protection from unauthorized use
• Power Management features
The settings made in the Setup Utility affect how the computer performs. Before
using the Setup Utility, ensure that you understand the Setup Utility options.
This chapter provides explanations for Setup Utility options.
The Standard Configuration

A standard configuration has already been set in the Setup Utility. However, we
recommend that you read this chapter in case you need to make any changes in the
future.
This Setup Utility should be used:

• when changing the system configuration
• when a configuration error is detected and you are prompted to make
changes to the Setup Utility
• when trying to resolve IRQ conflicts
• when making changes to the Power Management configuration
• when changing the password or making other changes to the Security
Setup
Entering the Setup Utility

When you power on the system, BIOS enters the Power-On Self Test (POST)
routines. POST is a series of built-in diagnostics performed by the BIOS. After the
POST routines are completed, the following message appears:
Press DEL to enter SETUP
Using BIOS
28
Press the delete key to access the BIOS Setup Utility.

CMOS Setup Utility -- Copyright (C) 1985-2005, American Megatrends, Inc.
f Standard CMOS Setup fFrequency/Voltage Control

f Advanced Setup Load Default Settings
f Advanced Chipset Setup fSupervisor Password
f Integrated Peripherals fUser Password
f Power Management Setup Save & Exit Setup
f PCI/PnP Setup Exit Without Saving
f PC Health Status
mnlk: Move Enter : Select +/-/: Value F10: Save and Exit
F1:General Help F9: Optimized Defaults ESC: Exit
v02.58 (C)Copyright 1985-2004, American Mega trends, Inc.
Using BIOS
When you start the Setup Utility, the main menu appears. The main menu of the
Setup Utility displays a list of the options that are available. A highlight indicates
which option is currently selected. Use the cursor arrow keys to move the highlight
to other options. When an option is highlighted, execute the option by pressing
<Enter>.
Some options lead to pop-up dialog boxes that prompt you to verify that you wish to
execute that option. Other options lead to dialog boxes that prompt you for infor-
mation.
Some options (marked with a triangle f) lead to submenus that enable you to change
the values for the option. Use the cursor arrow keys to scroll through the items in the
submenu.
In this manual, default values are enclosed in parenthesis. Submenu items are denoted
by a triangle f .
The default BIOS setting for this motherboard applies for most conditions
with optimum performance. It is not suggested to change the default
values in the BIOS setup and the manufacture takes no responsibility to
any damage caused by changing the BIOS settings.
BIOS Navigation Keys
The BIOS navigation keys are listed below:
KEY FUNCTION
ESC Exits the current menu
mnlk Scrolls through the items on a menu
+/-/PU/PD Modifies the selected field’s values
Enter Select
F9 Loads an optimized setting for better performance
F10 Saves the current configuration and exits setup
F1 Displays a screen that describes all key functions
Using BIOS
29
For the purpose of better product maintenance, the manufacture reserves

the right to change the BIOS items presented in this manual. The BIOS
setup screens shown in this chapter are for reference only and may differ
from the actual BIOS. Please visit the manufacture’s website for updated
manual.
Standard CMOS Setup
This option displays basic information about your system.
CMOS Setup Utility -- Copyright (C) 1985-2005, American Megatrends, Inc.
Standard CMOS Setup
System Date Sun 01/01/2007 Help Item

System Time 00 : 12 : 59
Use [Enter], [TAB]
fPrimary IDE Master Not Detected or [SHIFT-TAB] to
fPrimary IDE Slave Not Detected select a field.
fSecondary IDE Master Not Detected
fSecondary IDE Slave Not Detected Use [+] or [-] to
f Third IDE Master Not Detected configure system Date.
fThird IDE Slave Not Detected
PCI IDE BusMaster Enabled

Floppy A Not Deteced
mnlk : Move Enter : Select +/-/: Value F10: Save and Exit
F1: General Help F9: Optimized Defaults ESC: Exit
System Date & System Time

The Date and Time items show the current date and time on the computer. If you are
running a Windows OS, these items are automatically updated whenever you make
changes to the Windows Date and Time Properties utility.
f IDE Devices
Your computer has one IDE channel which can be installed with one or two devices
(Master and Slave). In addition, this motherboard supports two SATA channels and
each channel allows one SATA device to be installed. Use these items to configure
each device on the IDE channel.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
Primary IDE Master
Primary IDE Master Help Item

Device : Not Detected
Type Auto Select the type

LBA/Large Mode Auto of device connected
Block (Multi-Sector Transfer) Auto to the system.
PIO Mode Auto
DMA Mode Auto
S.M.A.R.T Auto
32Bit Data Transfer Enabled
F1: General Help F9: Optimized Defaults ESC: Exit
Using BIOS
30
Type (Auto)
Use this item to configure the type of the IDE device that you specify. If the feature
is enabled, it will enhance hard disk performance by reading or writing more data
during each transfer
LBA/Large Mode (Auto)
Use this item to set the LBA/Large mode to enhance hard disk performance by
optimizing the area the hard disk is visited each time.
Block (Multi-Sector Transfer) (Auto)
If the feature is enabled, it will enhance hard disk performance by reading or writing
more data during each transfer.
PIO Mode (Auto)
Use this item to set the PIO mode to enhance hard disk performance by optimizing
the hard disk timing.
DMA Mode (Auto)
DMA capability allows user to improve the transfer-speed and data-integrity for
compatible IDE devices.
S.M.A.R.T. (Auto)
The S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) system is a
diagnostics technology that monitors and predicts device performance. S.M.A.R.T.
software resides on both the disk drive and the host computer.
32Bit Data Transfer (Enabled)
Use this item to enable or disable 32Bit Data Transfer.
Press <Esc> to return to the Standard CMOS Setup page.
Advanced Setup
This page sets up more advanced information about your system. Handle this page
with caution. Any changes can affect the operation of your computer.
Advanced Setup
CPU TM function Enabled Help Item

Max CPUID Value Limit Disabled
Execute Disable Bit Disabled
For the processor its
Intel (R) SpeedStep (tm) tech. Disabled
CPUID belows 0F41h.
Enhanced Halt (C1E) Enabled
TM2 only can be enabled
Quick Power on Self Test Enabled
under below setting.
Boot up Numlock Status On
1.Freq.>=3.6GHz
APIC Mode Enabled
FSB800
Boot Other Device Enabled
2. Freq. >= 2.86GHz
Security Check System
FSB533
Using BIOS
31
CPU TM function (Enabled)

For some specific brands of CPU, you can use this item to control the CPU frequency
and voltage according to its temperature.
Max CPUID Value Limit (Disabled)
Use this item to enable or disable the Max CPU ID value limit. When supports
Prescott and LGA775 CPUs, enables this to prevent the system from “rebooting”
when trying to install Windows NT 4.0.
Execute Disable Bit (Disabled)
This item is a security feature that helps you protect your CPU and operating system
against malicious software executing code. This item is available when CPU supports
the feature.
Intel (R) SpeedStep (tm) tech. (Disabled)
This item allows users to enable or disable the EIST (Enhanced Intel Speedstep
Technology) function. This item shows only if the CPU supports EIST.
Enhanced Halt (C1E) (Enabled)

This item enables or disables enhanced halt.
Quick Power on Self Test (Enabled)
Enable this item to shorten the power on testing (POST) and have your system start
up faster. You might like to enable this item after you are confident that your system
hardware is operating smoothly.
Boot Up Numlock Status (On)
This item defines if the keyboard Num Lock key is active when your system is
APIC Mode (Enabled)
This item allows you to enable or disable the APCI (Advanced Programmable Inter-
rupt Controller) mode. APIC provides symmetric multi-processing (SMP) for sys-
tems, allowing support for up to 60 processors.
Boot Other Device (Enabled)
When enabled, the system searches all other possible locations for an operating
system if it fails to find one in the devices specified under the First, Second and
Security Check (System)
This item is set to enable or disable the security check
Press <Esc> to return to the main menu setting page.
Using BIOS
32
Advanced Chipset Setup

This page sets up more advanced information about your system. Handle this page
with caution. Any changes can affect the operation of your computer.

Advanced Chipset Setup
Configure DRAM Timing By SPD Help Item

DVMT Mode Select DVMT Mode
DVMT/Fixed Memory 128MB Options
Share Memory Size Enabled, 8MB
Manual
By SPD
Configure DRAM Timing (By SPD)

When this item is set to enable, the DDR timing is configured using SPD. SPD (Serial
Presence Detect) is located on the memory modules, BIOS reads information coded
in SPD during system boot up.
DVMT Mode Select (DVMT Mode)

This item allows you to select the DVMT operating mode.
DVMT/Fixed Memory (128MB)

When set to Fixed Mode, the graphics driver will reserve a fixed portion of the
system memory as graphics memory. When set to DVMT Mode, the graphics chip
will dynamically allocate system memory as graphics memory, according to system
and graphics requirements..
Share Memory Size (Enabled, 8MB)

This item lets you allocate a portion of the main memory for the onboard VGA
display application.
Using BIOS
33
Integrated Peripherals
This page sets up some parameters for peripheral devices connected to the system.
Integrated Peripherals
Onboard IDE Controller Enabled Help Item

Onboard SATA Controller Enabled
USB Functions Enabled
Legacy USB Support Enabled Disable / Enable the
Audio Controller Enabled integrated IDE
Onboard LAN Function Enabled Controller
Onboard LAN Boot ROM Disabled
Serial Port1 Address 3F8&IRQ4
Parallel Port Address 378
Parallel Port Mode ECP
ECP Mode DMA Channel DMA3
Parallel Port IRQ IRQ7
Onboard IDE Controller (Enabled)

Use this item to enable or disable the onboard IDE interface.
Onboard SATA Controller (Enabled)
Use this item to enable or disable the onboard SATA controller.
USB Functions (Enabled)
Use this item to enable or disable the USB function.
Legacy USB Support (Enabled)
Use this item to enable or disable support for legacy USB devices. Setting to Auto
allows the system to detect the presence of USB device at startup. If detected, the
USB controller legacy mode is enabled. If no USB device is detected, the legacy USB
support is disabled.
Audio Controller (Enabled)
Use this item to enable or disable the onboard audio controller.
OnBoard LAN Function (Enabled)
Use this item to enable or disable the onboard LAN function.
OnBoard LAN Boot ROM (Disabled)
Use this item to enable or disable the booting from the onboard LAN or a network
add-in card with a remote boot ROM installed.
Serial Port1 Address (3F8&IRQ4)
Use this item to enable or disable the onboard COM1/2 serial port, and to assign a
port address.
Parallel Port Address (378)
Use this item to enable or disable the onboard Parallel port, and to assign a port
address.
Using BIOS
34
Parallel Port Mode (ECP)

Use this item to select the parallel port mode. You can select Normal (Standard
Parallel Port), ECP (Extended Capabilities Port), EPP (Enhanced Parallel Port), or
BPP (Bi-Directional Parallel Port).
ECP Mode DMA Channel (DMA3)
Use this item to assign the DMA Channel under ECP Mode function.
Parallel Port IRQ (IRQ7)
Use this item to assign IRQ to the parallel port.
Power Management Setup

This page sets up some parameters for system power management operation.
Power Management Setup
*ACPI Suspend Type S3 (STR) Help Item

Soft-off by PWR-BTTN Delay 4 Sec
PWRON After PWR-Fail Power Off Select the ACPI
Resume On LAN Disabled state used for
Wake-Up by PME Enabled System Suspend.
Power On by Ring Disabled
USB KB Wakeup From S3 Disabled
PS2 Keyboard Wakeup Disabled
PS2 Mouse Wakeup Disabled
Resume on RTC Alarm Disabled
*ACPI Suspend Type (S3(STR))

Use this item to define how your system suspends. In the default, S3, the suspend
mode is a suspend to RAM, i.e, the system shuts down with the exception of a refresh
current to the system memory. This item will not show when the FSB reaches 1333
MHz.
Soft-Off By PWR-BTTN (Delay 4 Sec)
Under ACPI (Advanced Configuration and Power management Interface) you can
create a software power down. In a software power down, the system can be resumed
by Wake Up Alarms. This item lets you install a software power down that is con-
trolled by the power button on your system. If the item is set to Instant-Off, then the
power button causes a software power down. If the item is set to Delay 4 Sec, then
you have to hold the power button down for four seconds to cause a software power
down.
PWRON After PWR-Fail (Power Off)
This item enables your computer to automatically restart or return to its operating
status.
Resume On LAN (Disabled)
This item allows users to enable or disable LAN activity to wake up the system from
a power saving mode.
Using BIOS
35
Wake-Up by PME (Enabled)

The system can be turned off with a software command. If you enable this item, the
system can automatically resume if there is an incoming call on the PCI Modem or
PCI LAN card. You must use an ATX power supply in order to use this feature. Use
this item to do wake-up action if inserting the PCI card.
Power On by Ring (Disabled)
system can automatically resume if there is an incoming call on the Modem. You
must use an ATX power supply in order to use this feature.
USB KB Wakeup From S3 (Disabled)
This item allows you to enable/disable the USB device wakeup function from S3/S4
mode.
PS2 Keyboard Wakeup (Disabled)
This item enable or disable you to allow keyboard activity to awaken the system
from power saving mode.
PS2 Mouse Wakeup (Disabled)
This item enable or disable you to allow mouse activity to awaken the system from
power saving mode.
Resume on RTC Alarm (Disabled)
system can automatically resume at a fixed time based on the system’s RTC (realtime
clock). Use the items below this one to set the date and time of the wake-up alarm.
You must use an ATX power supply in order to use this feature.
PCI/PnP Setup
This page sets up some parameters for devices installed on the PCI bus and those
utilizing the system plug and play capability.
PCI/PnP Setup
Init Display First PCI Express Card Help Item

Allocate IRQ to PCI VGA Yes
Select which graphics
controller to use as
the primary boot
device.
Using BIOS
36
Init Display First (PCI Card)

Use this item to select which graphics controller to use as the primary boot devices.
Allocate IRQ to PCI VGA (Yes)
If this item is enabled, an IRQ will be assigned to the PCI VGA graphics system. You
set this value to No to free up an IRQ.
PC Health Status
On motherboards support hardware monitoring, this item lets you monitor the
parameters for critical voltages, temperatures and fan speeds.
PC Health Status
Help Item
Hardware Health Event Monitoring
fSmart Fan Function Press Enter
Shutdown Temperature Disabled
CPU Temperature 39°C/102°F
CPU Fan Speed 4272 RPM
CPU VCore 1.280 V
VDIMM 1.840 V
f Smart Fan Function

Scroll to this item and press <Enter> to view the following screen:
Smart Fan Function
SMART Fan Control Disabled Help Item
Fan configuration
mode setting
Using BIOS
37
SMART Fan Control (Disabled)

This item allows you to enable/disable the control of the system fan speed by chang-
ing the fan voltage.
Press <Esc> to return to the PC Health Status page.
Shutdown Temperature (Disabled)

Enable you to set the maximum temperature the system can reach before powering
down.
System Component Characteristics
These items display the monitoring of the overall inboard hardware health events,
such as System & CPU temperature, CPU & DIMM voltage, CPU & system fan
speed,...etc.
• CPU Temperature
• CPU Fan Speed
• CPU VCore
• VDIMM
Frequency/Voltage Control
This page enables you to set the clock speed and system bus for your system. The
clock speed and system bus are determined by the kind of processor you have in-
stalled in your system.
Frequency/Voltage Control
Manufacturer : Intel Help Item

Ratio Actual Value: 9
CPU Frequency Setting 266MHz Options
DRAM Frequncy Auto
Auto Detect DIMM/PCI Clk Enabled Auto
Spread Spectrum Disabled 400 MHz
CPU Frequency Auto 533 MHz
667 MHz
Manufacturer (Intel)
This item displays the information of current manufacturer of the CPU installed in
your computer.
Ratio Actual Value
These items show the locked ratio status and the actual ratio of the CPU installed in
your system.
CPU Frequency Setting (266 MHz)
This item indicates the current CPU frequency. Users can not make any change to
this item. Please be noted that the frequency will be varied with different CPU.
Using BIOS
38
DRAM Frequency (Auto)

This item shows the frequency of the DRAM in your computer. When it is FSB 1333
MHz CPU, the select options will be Auto, 533 MHz, and 667 MHz, and when it is
not FSB 1333 MHz CPU, the select options will be Auto, 400 MHz, 533 MHz and
667 MHz.
Auto Detect DIMM/PCI Clk (Enabled)
When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI slots.
Spread Spectrum (Disabled)
If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic
Interference) generated by the system.
CPU Frequency (Auto)
Use this option to adjust CPU frequency. And this item shows only when the FSB
reaches 1333 MHz.
Load Optimal Defaults

This option opens a dialog box that lets you install optimized defaults for all
appropriate items in the Setup Utility. Press <Y> and then <Enter> to install the
defaults. Press <N> and then <Enter> to not install the defaults. The optimized
defaults place demands on the system that may be greater than the performance
level of the components, such as the CPU and the memory. You can cause fatal
errors or instability if you install the optimized defaults when your hardware does
not support them. If you only want to install setup defaults for a specific option,
select and display that option, and then press <F7>.
Supervisor Password
This page helps you install or change a password.
Supervisor Password
Security Settings Help Item
Supervisor Password : Not Installed Install or Change the

Change Supervisor Password Press Enter password.
Using BIOS
39
Supervisor Password (Not Installed)

This item indicates whether a supervisor password has been set. If the password has
been installed, Installed displays. If not, Not Installed displays.
Change Supervisor Password (Press Enter)
You can select this option and press <Enter> to access the sub menu. You can use the
sub menu to change the supervisor password.
User Password
This page helps you install or change a password.

User Password
Security Settings Help Item
User Password : Not Installed Install or Change the

Change User Password Press Enter password.
User Password (Not Installed)

This item indicates whether a user password has been set. If the password has been
installed, Installed displays. If not, Not Installed displays.
Change User Password (Press Enter)
You can select this option and press <Enter> to access the sub menu. You can use the
sub menu to change the supervisor password. This item will show if Supervisor
Password is set.
Using BIOS
40
Save & Exit Setup

Highlight this item and press <Enter> to save the changes that you have made in the
Setup Utility and exit the Setup Utility. When the Save and Exit dialog box appears,
select [OK] to save and exit, or select [Cancel] to return to the main menu.
Exit Without Saving

Highlight this item and press <Enter> to discard any changes that you have made in
the Setup Utility and exit the Setup Utility. When the Exit Without Saving dialog
box appears, select [OK] to discard changes and exit, or select [Cancel] to return to
the main menu.
If you have made settings that you do not want to save, use the “Discard
Changes and Exit” item and select [OK] to discard any changes you have
made.
Using BIOS
41
Updating the BIOS

You can download and install updated BIOS for this motherboard from the
manufacturer’s Web site. New BIOS provides support for new peripherals, improve-
ments in performance, or fixes for known bugs. Install new BIOS as follows:
1 Create a bootable system disk. (Refer to Windows online help for
information on creating a bootable system disk.)
2 Download the Flash Utility and new BIOS file from the manufacturer’s
Web site. Copy these files to the bootable device.
3 Turn off your computer and insert the bootable device in your com-
puter. (You might need to run the Setup Utility and change the boot
priority items on the Advanced BIOS Features Setup page, to force
your computer to boot from the bootable device first.)
4 At the C:\ or A:\ prompt, type the Flash Utility program name and the file
name of the new bios and then press <Enter>. Example: AMINF340.EXE
040706.ROM
5 When the installation is complete, remove the bootable device from the
computer and restart your computer. If your motherboard has a Flash
BIOS jumper, reset the jumper to protect the newly installed BIOS from
being overwritten. The computer will restart automatically.
This concludes Chapter 3. Refer to the next chapter for information on the software
supplied with the motherboard.
Using BIOS
42
Memo
Using BIOS
43
Chapter 4
Using the Motherboard Software
About the Software CD-ROM
The support software CD-ROM that is included in the motherboard package contains
all the drivers and utility programs needed to properly run the bundled products.
Below you can find a brief description of each software program, and the location for
your motherboard version. More information on some programs is available in a
README file, located in the same directory as the software. Before installing any
software, always inspect the folder for files named README.TXT, INSTALL.TXT,
or something similar. These files may contain important information that is not
included in this manual.
1. Never try to install all software from folder that is not specified for use
with your motherboard.
2. The notice of Intel HD Audio Installation (optional): The Intel High
Definition audio functionality unexpectedly quits working in Windows
Server 2003 Service Pack 1 or Windows XP Professional x64 Edition.
Users need to download and install the update packages from the Microsoft
Download Center “before” installing HD audio driver bundled in the
driver CD. Please log on to http://support.microsoft.com/
default.aspx?scid=kb;en-us;901105#appliesto for more information.
Auto-installing under Windows 2000/XP
The Auto-install CD-ROM makes it easy for you to install the drivers and software
for your motherboard.
If the Auto-install CD-ROM does not work on your system, you can still
install drivers through the file manager for your OS (for example, Win-
dows Explorer). Refer to the Utility Folder Installation Notes later in this
chapter.
The support software CD-ROM disc loads automatically under Windows 2000/XP.
When you insert the CD-ROM disc in the CD-ROM drive, the autorun feature will
automatically bring up the install screen. The screen has three buttons on it, Setup,
Browse CD and Exit.
If the opening screen does not appear; double-click the file “setup.exe”
in the root directory.
44
Setup Tab
Setup Click the Setup button to run the software installation program.
Select from the menu which software you want to install.
Browse CD The Browse CD button is the standard Windows command that al-
lows you to open Windows Explorer and show the contents of the
support CD.
Before installing the software from Windows Explorer, look for a file
named README.TXT, INSTALL.TXT or something similar. This
file may contain important information to help you install the soft-
ware correctly.
Some software is installed in separate folders for different operating
systems, such as Windows 2000/XP. Always go to the correct folder
for the kind of OS you are using.
In install the software, execute a file named SETUP.EXE or
INSTALL.EXE by double-clicking the file and then following the in-
structions on the screen.
Exit The EXIT button closes the Auto Setup window.
Application Tab
Lists the software utilities that are available on the CD.
Read Me Tab
Displays the path for all software and drivers available on the CD.
Running Setup
Follow these instructions to install device drivers and software for the motherboard:
1. Click Setup. The installation program begins:
The following screens are examples only. The screens and driver lists
will be different according to the motherboard you are installing.
The motherboard identification is located in the upper left-hand corner.

45
2. Click Next. The following screen appears:
3. Check the box next to the items you want to install. The default options are recom
mended.
4. Click Next run the Installation Wizard. An item installation screen appears:
5. Follow the instructions on the screen to install the items.
Drivers and software are automatically installed in sequence. Follow the onscreen
instructions, confirm commands and allow the computer to restart a few times to
complete the installation.

46
Manual Installation
Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root
directory. This file contains the information needed to locate the drivers for your
motherboard.
Look for the chipset and motherboard model; then browse to the directory and path
to begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that
automatically detects your operating system before installation. Other drivers have
the setup program located in the operating system subfolder.
If the driver you want to install does not have a setup program, browse to the
operating system subfolder and locate the readme text file (README.TXT or
README.DOC) for information on installing the driver or software for your oper-
ating system.
Utility Software Reference

All the utility software available from this page is Windows compliant. They are
provided only for the convenience of the customer. The following software is fur-
nished under license and may only be used or copied in accordance with the terms of
the license.
These software(s) are subject to change at anytime without prior notice.
Please refer to the support CD for available software.
This concludes Chapter 4.

Ecs 945GCT-M2 - 1333

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Ecs 945GCT-M2 - 1333

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ecs 945GCT-M2 - 1333

Uploaded by

Copyright:

Available Formats

i

Federal Communications Commission (FCC)

Canadian Department of Communications

About the Manual

Chapter 1 Describes features of the motherboard.

Chapter 2 Describes installation of motherboard

Chapter 3 Provides information on using the BIOS

Chapter 4 Describes the motherboard software

“*” stands for this motherboard is ready to support Pentium D/ Pentium 4

Introducing the Motherboard

Onboard LAN (Optional)

• Integrated 10/100/1000 transceiver

• Supports 10/100 Mb/s N-Way Auto negotiation operation

1.Some hardware specifications and software items are subject to change

Introducing the Motherboard

Introducing the Motherboard

Table of Motherboard Components

“*” stands for this motherboard is ready to support Pentium D/Pentium 4

Introducing the Motherboard

Introducing the Motherboard

Choosing a Computer Case

Installing the Motherboard in a Case

Installing the Motherboard

Do not over-tighten the screws as this can stress the motherboard.

Checking Jumper Settings

The illustrations show a 2-pin jumper. When

This illustration shows a 3-pin jumper. Pins

Installing the Motherboard

Checking Jumper Settings

Jumper Type Description Setting (default)

1. To avoid the system unstability after clearing CMOS, we recommend

Before installing the Processor

Fail-Safe Procedures for Over-clocking

Installing the Motherboard

CPU Installation Procedure

A. Read and follow the instructions shown on the

C. Open the load plate

D. Install the CPU on the socket

E. Close the load plate

F. Apply thermal grease on top of the CPU.

G. Fasten the cooling fan supporting base onto

H. Make sure the CPU fan is plugged to the

Installing the Motherboard

Installing Memory Modules

DDR2 SDRAM memory module table

Installing the Motherboard

CPU FSB Frequency Memory Support Frequency

Installing the Motherboard

Type Size Vendor Module Nam e

Installing the Motherboard

Table B: DDR2(memory module) QVL (Qualified Vendor List)

Installing the Motherboard

1. Before installing an add-on card, check the documentation for the

Installing the Motherboard

Follow these instructions to install an add-on card:

Installing the Motherboard

Connecting Optional Devices

F_AUDIO1: Front Panel Audio header for Azalia