Series and parallel AC circuits This worksheet and all related les are licensed under the Creative

Commons Attribution License, version 1.0. To view a copy of this license, visit http://creativecommons.org/licenses/by/1.0/, or send a letter to Creative Commons, 559 Nathan Abbott Way, Stanford, California 94305, USA. The terms and conditions of this license allow for free copying, distribution, and/or modication of all licensed works by the general public. Resources and methods for learning about these subjects (list a few here, in preparation for your research):

Questions Question 1 Doorbell circuits connect a small lamp in parallel with the doorbell pushbutton so that there is light at the button when it is not being pressed. The lamps lament resistance is such that there is not enough current going through it to energize the solenoid coil when lit, which means the doorbell will ring only when the pushbutton switch shorts past the lamp:

Doorbell switch Solenoid 18 V 60 Hz Lamp

Suppose that such a doorbell circuit suddenly stops working one day, and the home owner assumes the power source has quit since the bell will not ring when the button is pressed and the lamp never lights. Although a dead power source is certainly possible, it is not the only possibility. Identify another possible failure in this circuit which would result in no doorbell action (no sound) and no light at the lamp. le 03447 Question 2 Calculate the total impedance oered by these two inductors to a sinusoidal signal with a frequency of 60 Hz:

750 mH L1 350 mH Ztotal @ 60 Hz = ??? L2

Show your work using two dierent problem-solving strategies: Calculating total inductance (Ltotal ) rst, then total impedance (Ztotal ). Calculating individual impedances rst (ZL1 and ZL2 ), then total impedance (Ztotal ). Do these two strategies yield the same total impedance value? Why or why not? le 01832

Question 3 Calculate the total impedance oered by these two capacitors to a sinusoidal signal with a frequency of 3 kHz:

C1 0.01 F Ztotal @ 3 kHz = ??? C2 0.022 F

Show your work using two dierent problem-solving strategies: Calculating total capacitance (Ctotal ) rst, then total impedance (Ztotal ). Calculating individual impedances rst (ZC 1 and ZC 2 ), then total impedance (Ztotal ). Do these two strategies yield the same total impedance value? Why or why not? le 01834 Question 4 Write an equation that solves for the impedance of this series circuit. The equation need not solve for the phase angle between voltage and current, but merely provide a scalar gure for impedance (in ohms):

Ztotal = ???

le 00850

Question 5 Write an equation that solves for the impedance of this series circuit. The equation need not solve for the phase angle between voltage and current, but merely provide a scalar gure for impedance (in ohms):

Ztotal = ???

le 01844

Question 6 A student measures voltage drops in an AC circuit using three voltmeters and arrives at the following measurements:

V V V
OFF A COM

A A
OFF

A V A

COM

V V
OFF

A A

COM

Upon viewing these measurements, the student becomes very perplexed. Arent voltage drops supposed to add in series, just as in DC circuits? Why, then, is the total voltage in this circuit only 10.8 volts and not 15.74 volts? How is it possible for the total voltage in an AC circuit to be substantially less than the simple sum of the components voltage drops? Another student, trying to be helpful, suggests that the answer to this question might have something to do with RMS versus peak measurements. A third student disagrees, proposing instead that at least one of the meters is badly out of calibration and thus not reading correctly. When you are asked for your thoughts on this problem, you realize that neither of the answers proposed thus far are correct. Explain the real reason for the discrepancy in voltage measurements, and also explain how you could experimentally disprove the other answers (RMS vs. peak, and bad calibration). le 01566

Question 7 Draw a phasor diagram showing the trigonometric relationship between resistance, reactance, and impedance in this series circuit:

2.2 k R 5 V RMS 350 Hz L 680 mH

Show mathematically how the resistance and reactance combine in series to produce a total impedance (scalar quantities, all). Then, show how to analyze this same circuit using complex numbers: regarding component as having its own impedance, demonstrating mathematically how these impedances add up to comprise the total impedance (in both polar and rectangular forms). le 01827 Question 8 Calculate the magnitude and phase shift of the current through this inductor, taking into consideration its intrinsic winding resistance:

Inductor

65

1.5 H

Vin 10 VAC 135 Hz

le 00639

Question 9 Calculate the necessary size of the capacitor to give this circuit a total impedance (Ztotal ) of 4 k, at a power supply frequency of 100 Hz:

2k2 100 Hz C = ???

le 04042 Question 10 Draw a phasor diagram showing the trigonometric relationship between resistance, reactance, and impedance in this series circuit:

2.2 k R 5 V RMS 350 Hz C 0.22 F

Show mathematically how the resistance and reactance combine in series to produce a total impedance (scalar quantities, all). Then, show how to analyze this same circuit using complex numbers: regarding each of the component as having its own impedance, demonstrating mathematically how these impedances add up to comprise the total impedance (in both polar and rectangular forms). le 01828

Question 11 Which component, the resistor or the capacitor, will drop more voltage in this circuit?

47n 725 Hz 5k1

Also, calculate the total impedance (Ztotal ) of this circuit, expressing it in both rectangular and polar forms. le 03784 Question 12 Calculate the total impedance of this series LR circuit and then calculate the total circuit current:

250m

5k1

34 V RMS 3 kHz
Also, draw a phasor diagram showing how the individual component impedances relate to the total impedance. le 02103

Question 13 A quantity sometimes used in DC circuits is conductance, symbolized by the letter G. Conductance is 1 ), and it is measured in the unit of siemens. the reciprocal of resistance (G = R Expressing the values of resistors in terms of conductance instead of resistance has certain benets in parallel circuits. Whereas resistances (R) add in series and diminish in parallel (with a somewhat complex equation), conductances (G) add in parallel and diminish in series. Thus, doing the math for series circuits is easier using resistance and doing math for parallel circuits is easier using conductance:

Rtotal = R1 + R2 + R3

Gtotal = G1 + G2 + G3

R1 R2 R3 Rtotal = 1 1 1 1 + + R1 R2 R3 R1 R2 R3

Gtotal =

1 1 1 1 + + G1 G2 G3

In AC circuits, we also have reciprocal quantities to reactance (X ) and impedance (Z ). The reciprocal 1 1 of reactance is called susceptance (B = X ), and the reciprocal of impedance is called admittance (Y = Z ). Like conductance, both these reciprocal quantities are measured in units of siemens. Write an equation that solves for the admittance (Y ) of this parallel circuit. The equation need not solve for the phase angle between voltage and current, but merely provide a scalar gure for admittance (in siemens):

Ytotal = ???

le 00853

Question 14 A quantity sometimes used in DC circuits is conductance, symbolized by the letter G. Conductance is 1 ), and it is measured in the unit of siemens. the reciprocal of resistance (G = R Expressing the values of resistors in terms of conductance instead of resistance has certain benets in parallel circuits. Whereas resistances (R) add in series and diminish in parallel (with a somewhat complex equation), conductances (G) add in parallel and diminish in series. Thus, doing the math for series circuits is easier using resistance and doing math for parallel circuits is easier using conductance:

Rtotal = R1 + R2 + R3

Gtotal = G1 + G2 + G3

R1 R2 R3 Rtotal = 1 1 1 1 + + R1 R2 R3 R1 R2 R3

Gtotal =

1 1 1 1 + + G1 G2 G3

In AC circuits, we also have reciprocal quantities to reactance (X ) and impedance (Z ). The reciprocal 1 1 of reactance is called susceptance (B = X ), and the reciprocal of impedance is called admittance (Y = Z ). Like conductance, both these reciprocal quantities are measured in units of siemens. Write an equation that solves for the admittance (Y ) of this parallel circuit. The equation need not solve for the phase angle between voltage and current, but merely provide a scalar gure for admittance (in siemens):

Ytotal = ???

le 01845

10

Question 15 Calculate the total impedance oered by these three resistors to a sinusoidal signal with a frequency of 10 kHz: R1 = 3.3 k R2 = 10 k R3 = 5 k

Surface-mount resistors on a printed-circuit board

R1

R2

R3

Ztotal @ 10 kHz = ???

State your answer in the form of a scalar number (not complex), but calculate it using two dierent strategies: Calculate total resistance (Rtotal ) rst, then total impedance (Ztotal ). Calculate individual admittances rst (YR1 , YR2 , and YR3 ), then total impedance (Ztotal ). le 01836 Question 16 Calculate the total impedance oered by these three capacitors to a sinusoidal signal with a frequency of 4 kHz: C1 = 0.1 F C2 = 0.047 F C3 = 0.033 F

Surface-mount capacitors on a printed-circuit board

C1

C2

C3

Ztotal @ 4 kHz = ???

State your answer in the form of a scalar number (not complex), but calculate it using two dierent strategies: Calculate total capacitance (Ctotal ) rst, then total impedance (Ztotal ). Calculate individual admittances rst (YC 1 , YC 2 , and YC 3 ), then total impedance (Ztotal ). le 01846

11

Question 17 Calculate the total impedance of these parallel-connected components, expressing it in polar form (magnitude and phase angle):

Surface-mount components on a printed-circuit board

C1

33n

R1

510

Ztotal @ 7.9 kHz = ???

Also, draw an admittance triangle for this circuit. le 02108 Question 18 Calculate the total impedance of this LR circuit, once using nothing but scalar numbers, and again using complex numbers:
R1 1k5 50m L1

Ztotal @ 8 kHz = ???

le 01837

12

Question 19 Calculate the total impedance oered by these two inductors to a sinusoidal signal with a frequency of 120 Hz:

Ztotal @ 120 Hz = ??? 500 mH L1 1.8 H L2

Show your work using three dierent problem-solving strategies: Calculating total inductance (Ltotal ) rst, then total impedance (Ztotal ). Calculating individual admittances rst (YL1 and YL2 ), then total admittance (Ytotal ), then total impedance (Ztotal ). Using complex numbers: calculating individual impedances rst (ZL1 and ZL2 ), then total impedance (Ztotal ). Do these two strategies yield the same total impedance value? Why or why not? le 01833 Question 20 Calculate the total impedance of this RC circuit, once using nothing but scalar numbers, and again using complex numbers:

Ztotal @ 400 Hz = ???

R1
7.9 k

C1 0.047 F

le 01838

13

Question 21 Calculate the total impedance oered by these two capacitors to a sinusoidal signal with a frequency of 900 Hz:

C1 0.33 F Ztotal @ 900 Hz = ??? C2 0.1 F

Show your work using three dierent problem-solving strategies: Calculating total capacitance (Ctotal ) rst, then total impedance (Ztotal ). Calculating individual admittances rst (YC 1 and YC 2 ), then total admittance (Ytotal ), then total impedance (Ztotal ). Using complex numbers: calculating individual impedances rst (ZC1 and ZC2 ), then total impedance (Ztotal ). Do these two strategies yield the same total impedance value? Why or why not? le 01835 Question 22 Calculate the total impedance for these two 100 mH inductors at 2.3 kHz, and draw a phasor diagram showing circuit impedances (Ztotal , R, and X ):
L1 100m L2 100m

Ztotal @ 2.3 kHz = ???

Now, re-calculate impedance and re-draw the phasor impedance diagram supposing the second inductor is replaced by a 1.5 k resistor:
L1 100m R1 1k5

Ztotal @ 2.3 kHz = ???

le 02080

14

Question 23 Calculate the total impedance for these two 100 mH inductors at 2.3 kHz, and draw a phasor diagram showing circuit admittances (Ytotal , G, and B ):
100m L1 100m L2

Ztotal @ 2.3 kHz = ???

Now, re-calculate impedance and re-draw the phasor admittance diagram supposing the second inductor is replaced by a 1.5 k resistor:
100m L1 1k5 R1

Ztotal @ 2.3 kHz = ???

le 02079 Question 24 Calculate the individual currents through the inductor and through the resistor, the total current, and the total circuit impedance:

5k1

250m

2.5 V RMS 3 kHz

Also, draw a phasor diagram showing how the individual component currents relate to the total current. le 02104

15

Question 25 Due to the eects of a changing electric eld on the dielectric of a capacitor, some energy is dissipated in capacitors subjected to AC. Generally, this is not very much, but it is there. This dissipative behavior is typically modeled as a series-connected resistance:

Equivalent Series Resistance (ESR) Real capacitor Ideal capacitor

Calculate the magnitude and phase shift of the current through this capacitor, taking into consideration its equivalent series resistance (ESR):

Capacitor

5 0.22 F

Vin 10 VAC 270 Hz

Compare this against the magnitude and phase shift of the current for an ideal 0.22 F capacitor. le 01847 Question 26 Solve for all voltages and currents in this series LR circuit:

175 mH

15 V RMS 1 kHz 710

le 01830

16

Question 27 Solve for all voltages and currents in this series LR circuit, and also calculate the phase angle of the total impedance:

10.3 H

5 k

24 V RMS 50 Hz
le 01831 Question 28 Solve for all voltages and currents in this series RC circuit:

0.01 F

15 V RMS 1 kHz 4.7 k

le 01848 Question 29 Solve for all voltages and currents in this series RC circuit, and also calculate the phase angle of the total impedance:

220n

3k3

48 V peak 30 Hz
le 01849

17

Question 30 One way to vary the amount of power delivered to a resistive AC load is by varying another resistance connected in series:

Rseries

Rload

A problem with this power control strategy is that power is wasted in the series resistance (I 2 Rseries ). A dierent strategy for controlling power is shown here, using a series inductance rather than resistance:

Lseries

Rload

Explain why the latter circuit is more power-ecient than the former, and draw a phasor diagram showing how changes in Lseries aect Ztotal . le 01829

18

Question 31 A technician needs to know the value of a capacitor, but does not have a capacitance meter nearby. In lieu of this, the technician sets up the following circuit to measure capacitance:

Volts/Div A
0.5 0.2 0.1 1 2 5 10 20 50 m 20 m 10 m 5m 2m

Sec/Div
1m 5m 250 50 10 2.5 0.5 0.1 0.025

Position

25 m 100 m 500 m 1 2.5 off

DC Gnd AC

X-Y Position A B Alt Chop Add Triggering Level A B Alt Line Ext. Intensity
Off Cal 1 V Gnd Trace rot.

Volts/Div B
0.5 0.2 0.1 1 2 50 m 20 m 10 m 5m 2m

Holdoff Ext. input

Position Invert Focus Beam find Norm Auto Single Reset AC DC

5 10 20

DC Gnd AC

Slope

LF Rej HF Rej

Cx
FUNCTION GENERATOR Hz 1 coarse fine 10 100 1k 10k 100k 1M

DC

output

You happen to walk by this technicians workbench and ask, How does this measurement setup work? The technician responds, You connect a resistor of known value (R) in series with the capacitor of unknown value (Cx ), then adjust the generator frequency until the oscilloscope shows the two voltage drops to be equal, and then you calculate Cx . Explain how this system works, in your own words. Also, write the formula you would use to calculate the value of Cx given f and R. le 02114

19

Question 32 A large AC electric motor under load can be considered as a parallel combination of resistance and inductance:

AC motor 240 VAC 60 Hz Leq Req

Calculate the current necessary to power this motor if the equivalent resistance and inductance is 20 and 238 mH, respectively. le 01839 Question 33 A large AC electric motor under load can be considered as a parallel combination of resistance and inductance:

AC motor 277 VAC 60 Hz Leq Req

Calculate the equivalent inductance (Leq ) if the measured source current is 27.5 amps and the motors equivalent resistance (Req ) is 11.2 . le 01840

20

Question 34 Calculate the total impedances (complete with phase angles) for each of the following inductor-resistor circuits:

0.5 H 470 290 Hz

200 mH 1.5 k 1H

100 Hz

100 Hz

0.5 H

470

0.2 H 290 Hz 1H

1.5 k

le 02106 Question 35 A doorbell ringer has a solenoid with an inductance of 63 mH connected in parallel with a lamp (for visual indication) having a resistance of 150 ohms:

Doorbell switch Solenoid 18 V 60 Hz Lamp

Calculate the phase shift of the total current (in units of degrees) in relation to the total supply voltage, when the doorbell switch is actuated. le 02105

21

Question 36 If the dielectric substance between a capacitors plates is not a perfect insulator, there will be a path for direct current (DC) from one plate to the other. This is typically called leakage resistance, and it is modeled as a shunt resistance to an ideal capacitance:

Real capacitor

Ideal capacitor

Leakage resistance

Calculate the magnitude and phase shift of the current drawn by this real capacitor, if powered by a sinusoidal voltage source of 30 volts RMS at 400 Hz:

0.75 F

Rleakage = 1.5 M

30 V RMS 400 Hz

Compare this against the magnitude and phase shift of the current for an ideal capacitor (no leakage). le 01850 Question 37 Voltage divider circuits may be constructed from reactive components just as easily as they may be constructed from resistors. Take this capacitive voltage divider, for instance:

C1

0.1 F Vin 10 VAC 250 Hz

Vout

C2

0.47 F

Calculate the magnitude and phase shift of Vout . Also, describe what advantages a capacitive voltage divider might have over a resistive voltage divider. le 00638

22

Question 38 A student is asked to calculate the phase shift for the following circuits output voltage, relative to the phase of the source voltage:

C Vsource R Vout

He recognizes this as a series circuit, and therefore realizes that a right triangle would be appropriate for representing component impedances and component voltage drops (because both impedance and voltage are quantities that add in series, and the triangle represents phasor addition):

R , VR
Zt
ota l

,V

tot

al

XC , VC

The problem now is, which angle does the student solve for in order to nd the phase shift of Vout ? The triangle contains two angles besides the 90o angle, and . Which one represents the output phase shift, and more importantly, why? le 03748 Question 39 Calculate the output voltage of this phase-shifting circuit, expressing it in polar form (magnitude and phase angle relative to the source voltage):

1.5 k Vout Vin 10 VAC 250 Hz 0.47 F

le 02620

23

Question 40 Calculate the output voltage of this phase-shifting circuit, expressing it in polar form (magnitude and phase angle relative to the source voltage):

Vin 5.4 VAC 1.2 kHz

0.033 F Vout 2.2 k

le 02621 Question 41 In this circuit, a series resistor-capacitor network creates a phase-shifted voltage for the gate terminal of a power-control device known as a TRIAC. All portions of the circuit except for the RC network are shaded for de-emphasis:

Lamp

330 k

AC source

TRIAC

DIAC

0.068 F

Calculate how many degrees of phase shift the capacitors voltage is, compared to the total voltage across the series RC network, assuming a frequency of 60 Hz, and a 50% potentiometer setting. le 00637 Question 42 Determine the input frequency necessary to give the output voltage a phase shift of 70o :

0.022 F Vin f = ??? 3.3 k Vout

le 02623

24

Question 43 Determine the input frequency necessary to give the output voltage a phase shift of 40o :

0.01 F Vin f = ??? 2.9 k Vout

le 02622 Question 44 Determine the input frequency necessary to give the output voltage a phase shift of -38o :

8.1 k Vin f = ??? 33 nF Vout

le 02626 Question 45 Determine the input frequency necessary to give the output voltage a phase shift of -25o :

1.7 k Vin f = ??? 0.047 F Vout

le 02625

25

Question 46 Determine the input frequency necessary to give the output voltage a phase shift of 75o :

12k5 Vin f = ??? Vout R 47m L

Also, write an equation that solves for frequency (f ), given all the other variables (R, L, and phase angle ). le 03282 Question 47 Determine the necessary resistor value to give the output voltage a phase shift of 44o :

R = ??? Vout 3.5 V 15 kHz 75 m L

Also, write an equation that solves for this resistance value (R), given all the other variables (f , L, and phase angle ). le 03283 Question 48 Determine the input frequency necessary to give the output voltage a phase shift of -40o :

Vin f = ???

100m L 2k1 R

Vout

Also, write an equation that solves for frequency (f ), given all the other variables (R, L, and phase angle ). le 03280

26

Question 49 Determine the necessary resistor value to give the output voltage a phase shift of -60o :

100m 10 V 8 kHz L R = ???

Vout

Also, write an equation that solves for this resistance value (R), given all the other variables (f , L, and phase angle ). le 03281 Question 50 Determine the input frequency necessary to give the output voltage a phase shift of 25o :

27n Vin f = ??? C 5k9 R Vout

Also, write an equation that solves for frequency (f ), given all the other variables (R, C , and phase angle ). le 03284 Question 51 Determine the necessary resistor value to give the output voltage a phase shift of 58o :

33n C 9V 4.5 kHz R = ??? Vout

Also, write an equation that solves for this resistance value (R), given all the other variables (f , C , and phase angle ). le 03285

27

Question 52 Determine the necessary resistor value to give the output voltage a phase shift of -64o :

R = ??? Vout 11 V 1.3 kHz 15n C

Also, write an equation that solves for this resistance value (R), given all the other variables (f , C , and phase angle ). le 03287 Question 53 Use algebraic substitution to generate an equation expressing the output voltage of the following circuit given the input voltage, the input frequency, the capacitor value, and the resistor value:

C Vout Vin R

Vout = le 03818 Question 54 Use algebraic substitution to generate an equation expressing the output voltage of the following circuit given the input voltage, the input frequency, the capacitor value, and the resistor value:

C1

C2 Vout

Vin

Vout = le 03819

28

Question 55 Determine the total current and all voltage drops in this circuit, stating your answers the way a multimeter would register them:

L1 R1

L2 R2

Vsupply
L1 = 250 mH L2 = 60 mH R1 = 6.8 k R2 = 1.2 k Vsupply = 13.4 V RMS fsupply = 6.5 kHz

Also, calculate the phase angle () between voltage and current in this circuit, and explain where and how you would connect an oscilloscope to measure that phase shift. le 01841

29

Question 56 Determine the total current and all component currents in this circuit, stating your answers the way a multimeter would register them:

L1 R1

L2 R2

Vsupply
L1 = 1.2 H L2 = 650 mH R1 = 33 k R2 = 27 k Vsupply = 19.7 V RMS fsupply = 4.5 kHz

Also, calculate the phase angle () between voltage and current in this circuit, and explain where and how you would connect an oscilloscope to measure that phase shift. le 01842

30

Question 57 Determine the total current and all voltage drops in this circuit, stating your answers the way a multimeter would register them:

C1 R2 C2 R1

C1 = 125 pF C2 = 71 pF R1 = 6.8 k R2 = 1.2 k Vsupply = 20 V RMS fsupply = 950 kHz

Also, calculate the phase angle () between voltage and current in this circuit, and explain where and how you would connect an oscilloscope to measure that phase shift. le 01851 Question 58 Calculate the voltage drops across all components in this circuit, expressing them in complex (polar) form with magnitudes and phase angles each:

1.5 V 180 Hz
0.01 F C1 R1 7.1 k C2 0.15 F

le 01852

31

Question 59 Determine the phase angle () of the current in this circuit, with respect to the supply voltage:

V V
OFF

A A

COM

R1

C1
FUNCTION GENERATOR Hz 1 coarse fine 10 100 1k 10k 100k 1M

DC

output

V V
OFF

A A

COM

le 01853

32

Question 60 Calculate the total (source) current in this parallel RC circuit, based on the readings taken by the dual-trace oscilloscope (both of the inductive current probes show branch currents in units of 1 amp per division):

A B

A B

Itotal = le 04065 Question 61 Calculate the total impedances (complete with phase angles) for each of the following capacitor-resistor circuits:

3.3 F

0.1 F

100 Hz

470

290 Hz

1.5 k

0.22 F

3.3 F 100 Hz

470

0.1 F

0.22 F

290 Hz

1.5 k

le 02109

33

Question 62 Complete the table of values for this circuit, representing all quantities in complex-number form (either polar or rectangular, your choice):

R1 470

3.3 F

C1

17 V 60 Hz

R1 V I Z
le 03611 Question 63

C1

Total 17 V 0o

Determine the size of capacitor (in Farads) necessary to create a total current of 11.3 mA in this parallel RC circuit:

11.3 mA

5.2 V 500 Hz

790

le 02110

34

Question 64 The input impedance of an electrical test instrument is a very important parameter in some applications, because of how the instrument may load the circuit being tested. Oscilloscopes are no dierent from voltmeters in this regard:

Volts/Div A
0.5 0.2 0.1 1 2 5 50 m 20 m 10 m 5m 2m

Sec/Div
1m 5m 250 50 10 2.5 0.5 0.1 1 2.5 off 0.025

Position

25 m 100 m 500 m

Zinput Input impedance (how much impedance the tested circuit "sees" from the oscilloscope)

10 20

DC Gnd AC

X-Y Position A B Alt Chop Add Triggering Level A B Alt Line Ext. Intensity
Off Cal 1 V Gnd Trace rot.

Volts/Div B
0.5 0.2 0.1 1 2 5 10 20 50 m 20 m 10 m 5m 2m

Holdoff Ext. input

Position Invert Focus Beam find Norm Auto Single Reset AC DC

DC Gnd AC

Slope

LF Rej HF Rej

Typical input impedance for an oscilloscope is 1 M of resistance, in parallel with a small amount of capacitance. At low frequencies, the reactance of this capacitance is so high that it may be safely ignored. At high frequencies, though, it may become a substantial load to the circuit under test:

Oscilloscope input (typical)

To circuit under test

1 M

20 pF

Calculate how many ohms of impedance this oscilloscope input (equivalent circuit shown in the above schematic) will impose on a circuit with a signal frequency of 150 kHz. le 02111

35

Question 65 If the source voltage in this circuit is assumed to be the phase reference (that is, the voltage is dened to be at an angle of 0 degrees), determine the relative phase angles of each current in this parallel circuit:

Itotal

IR

IC

I (R) = I (C ) = I (total) = le 02112 Question 66 Capacitors and inductors are complementary components both conceptually and mathematically, they seem to be almost exact opposites of each other. Calculate the total impedance of this series-connected inductor and capacitor network:

Ztotal = ???

XL = 45

XC = 58

le 00851

36

Question 67 Write an equation that solves for the impedance of this series circuit. The equation need not solve for the phase angle between voltage and current, but merely provide a scalar gure for impedance (in ohms):

Ztotal = ???

XL

XC

le 00852 Question 68 Is this circuits overall behavior capacitive or inductive? In other words, from the perspective of the AC voltage source, does it appear as though a capacitor is being powered, or an inductor?

0.1 F 85 mH

15 V 1.8 kHz

Now, suppose we take these same components and re-connect them in parallel rather than series. Does this change the circuits overall appearance to the source? Does the source now see an equivalent capacitor or an equivalent inductor? Explain your answer.

85 mH

0.1 F

15 V 1.8 kHz

le 01554

37

Question 69 Calculate the voltage dropped across the inductor, the capacitor, and the 8-ohm speaker in this sound system at the following frequencies, given a constant source voltage of 15 volts:

47 F

2 mH

8 Amplifier 15 VAC

f = 200 Hz f = 550 Hz f = 900 Hz Regard the speaker as nothing more than an 8-ohm resistor. le 00640 Question 70 Suppose you are building a circuit and you need an impedance of 1500 -41o at a frequency of 600 Hz. What combination of components could you connect together in series to achieve this precise impedance? le 00644

38

Question 71 Write an equation that solves for the admittance of this parallel circuit. The equation need not solve for the phase angle between voltage and current, but merely provide a scalar gure for admittance (in siemens):

Ytotal = ???

BL

BC

le 00854 Question 72 Calculate the total impedance of this parallel network, given a signal frequency of 12 kHz:

Ztotal = ???

1n

10k

105m

le 01541 Question 73 An AC electric motor operating under loaded conditions draws a current of 11 amps (RMS) from the 120 volt (RMS) 60 Hz power lines. The measured phase shift between voltage and current for this motor is 34o , with voltage leading current. Determine the equivalent parallel combination of resistance (R) and inductance (L) that is electrically equivalent to this operating motor. le 01542 Question 74 Calculate the impedance of a 145 mH inductor connected in series with 750 resistor at a frequency of 1 kHz, then determine the necessary resistor and inductor values to create the exact same total impedance in a parallel conguration. le 00645

39

Question 75 Dont just sit there! Build something!! Learning to mathematically analyze circuits requires much study and practice. Typically, students practice by working through lots of sample problems and checking their answers against those provided by the textbook or the instructor. While this is good, there is a much better way. You will learn much more by actually building and analyzing real circuits, letting your test equipment provide the answers instead of a book or another person. For successful circuit-building exercises, follow these steps: Carefully measure and record all component values prior to circuit construction. Draw the schematic diagram for the circuit to be analyzed. Carefully build this circuit on a breadboard or other convenient medium. Check the accuracy of the circuits construction, following each wire to each connection point, and verifying these elements one-by-one on the diagram. 5. Mathematically analyze the circuit, solving for all voltage and current values. 6. Carefully measure all voltages and currents, to verify the accuracy of your analysis. 7. If there are any substantial errors (greater than a few percent), carefully check your circuits construction against the diagram, then carefully re-calculate the values and re-measure. For AC circuits where inductive and capacitive reactances (impedances) are a signicant element in the calculations, I recommend high quality (high-Q) inductors and capacitors, and powering your circuit with low frequency voltage (power-line frequency works well) to minimize parasitic eects. If you are on a restricted budget, I have found that inexpensive electronic musical keyboards serve well as function generators for producing a wide range of audio-frequency AC signals. Be sure to choose a keyboard voice that closely mimics a sine wave (the panute voice is typically good), if sinusoidal waveforms are an important assumption in your calculations. As usual, avoid very high and very low resistor values, to avoid measurement errors caused by meter loading. I recommend resistor values between 1 k and 100 k. One way you can save time and reduce the possibility of error is to begin with a very simple circuit and incrementally add components to increase its complexity after each analysis, rather than building a whole new circuit for each practice problem. Another time-saving technique is to re-use the same components in a variety of dierent circuit congurations. This way, you wont have to measure any components value more than once. le 00605 1. 2. 3. 4.

40

Answers Answer 1 Solenoid coil failed open Wire broken anywhere in circuit Answer 2 First strategy: Ltotal = 1.1 H Xtotal = 414.7 Ztotal = 414.7

90o or Ztotal = 0 + j 414.7

Second strategy: XL1 = 282.7 ZL1 = 282.7 90o XL2 = 131.9 ZL2 = 131.9 90o Ztotal = 414.7 90o or Ztotal = 0 + j 414.7 Follow-up question: draw a phasor diagram showing how the two inductors impedance phasors geometrically add to equal the total impedance. Answer 3 First strategy: Ctotal = 6.875 nF Xtotal = 7.717 k Ztotal = 7.717 k

90o or Ztotal = 0 j 7.717 k

Second strategy: XC 1 = 5.305 k ZC1 = 5.305 k 90o XC 2 = 2.411 k ZC1 = 2.411 k 90o Ztotal = 7.717 k 90o or Ztotal = 0 j 7.717 k Answer 4 Ztotal = R2 + X 2 Follow-up question: algebraically manipulate this equation to produce two more; one solving for R and the other solving for X . Answer 5 Ztotal = R2 + X 2 Answer 6 AC voltages still add in series, but phase must also be accounted for when doing so. Unfortunately, multimeters provide no indication of phase whatsoever, and thus do not provide us with all the information we need. (Note: just by looking at this circuits components, though, you should still be able to calculate the correct result for total voltage and validate the measurements.) Ill let you determine how to disprove the two incorrect explanations oered by the other students! Challenge question: calculate a set of possible values for the capacitor and resistor that would generate these same voltage drops in a real circuit. Hint: you must also decide on a value of frequency for the power source.

41

Answer 7

Z tota

6 2.6

XL = 1.495 k

R = 2.2 k
Scalar calculations R = 2.2 k XL = 1.495 k Zseries = R2 + XL 2 Zseries = 22002 + 14952 = 2660 Complex number calculations ZL = 1.495 k 90o (Polar form) ZR = 2.2 k 0o ZR = 2.2 k + j 0 ZL = 0 + j 1.495 k (Rectangular form) Zseries = Z1 + Z2 + Zn (General rule of series impedances) Zseries = ZR + ZL (Specic application to this circuit) Zseries = 2.2 k 0o + 1.495 k 90o = 2.66 k 34.2o Zseries = (2.2 k + j 0 ) + (0 + j 1.495 k) = 2.2 k + j 1.495 k Answer 8 I = 7.849 mA Answer 9 C = 0.476 F

-87.08o

42

Answer 10

R = 2.2 k

Scalar calculations R = 2.2 k XC = 2.067 k Zseries = R2 + XC 2 Zseries = 22002 + 20672 = 3019 Complex number calculations ZC = 2.067 k 90o (Polar form) ZR = 2.2 k 0o ZR = 2.2 k + j 0 ZC = 0 j 2.067 k (Rectangular form) Zseries = Z1 + Z2 + Zn (General rule of series impedances) Zseries = ZR + ZC (Specic application to this circuit)

Zseries = 2.2 k 0o + 2.067 k 90o = 3.019 k 43.2o Zseries = (2.2 k + j 0 ) + (0 j 2.067 k) = 2.2 k j 2.067 k Answer 11 The resistor will drop more voltage. Ztotal (rectangular form) = 5100 - j4671 Ztotal (polar form) = 6916 Answer 12 Ztotal = 6.944 k I = 4.896 mA RMS Answer 13 Ytotal = G2 + B 2 -42.5o

Follow-up question #1: draw a phasor diagram showing how Y , G, and B relate. Follow-up question #2: re-write this equation using quantities of resistance (R), reactance (X ), and impedance (Z ), instead of conductance (G), susceptance (B ), and admittance (Y ). Answer 14 Ytotal =

Z to

XC = 2.067 k

l ta

= 9 01 3. k

G2 + B 2

Follow-up question #1: draw a phasor diagram showing how Y , G, and B relate. Follow-up question #2: re-write this equation using quantities of resistance (R), reactance (X ), and impedance (Z ), instead of conductance (G), susceptance (B ), and admittance (Y ).

43

Answer 15 First strategy: Rtotal = 1.658 k Ztotal = 1.658 k Second strategy: YR1 = 303 S YR2 = 100 S YR3 = 200 S Ytotal = 603 S Ztotal = 1.658 k Answer 16 First strategy: Ctotal = 0.18 F Ztotal = 221 Second strategy: YC 1 = 2.51 mS YC 2 = 1.18 mS YC 3 = 829 S Ytotal = 4.52 mS Ztotal = 221 Answer 17 Ztotal = 391.4 -39.9o

Ytotal = 2.555 mS YC1 = 1.638 mS 39.9o YR1 = 1.961 mS

Answer 18 Scalar calculations R1 = 1.5 k GR1 = 666.7 S XL1 = 2 .513 k BL1 = 397.9 S Ytotal = G2 + B 2 = 776.4 S 1 Ztotal = Ytotal = 1.288 k Complex number calculations R1 = 1.5 k ZR1 = 1.5 k 0o XL1 = 2.513 k ZL1 = 2.513 k 90o 1 Ztotal = 1 + = 1.288 k 30.83o 1
ZR1 ZL1

44

Answer 19 First strategy: Ltotal = 391.3 mH Xtotal = 295.0 Ztotal = 295.0 90o or Ztotal = 0 + j 295.0 Second strategy: ZL1 = XL1 = 377.0 YL1 = YL2 =
1 ZL1

= 2.653 mS = 736.8 S = 295

ZL1 = XL2 = 1.357 k

1 ZL2

Ytotal = 3.389 mS Ztotal =

1 Ytotal

Third strategy: (using complex numbers) XL1 = 377.0 ZL1 = 377.0 90o XL2 = 1.357 k ZL2 = 1.357 k 90o Ztotal = 295.0 90o or Ztotal = 0 + j 295.0 Follow-up question: draw a phasor diagram showing how the two inductors admittance phasors geometrically add to equal the total admittance. Answer 20 Scalar calculations R1 = 7.9 k GR1 = 126.6 S XC 1 = 8 .466 k BC 1 = 118.1 S Ytotal = G2 + B 2 = 173.1 S 1 Ztotal = Ytotal = 5.776 k Complex number calculations R1 = 7.9 k ZR1 = 7.9 k 0o XC 1 = 8.466 k ZC1 = 8.466 k 90o 1 Ztotal = 1 + = 5.776 k 43.02o 1
ZR1 ZC1

Answer 21 First strategy: Ctotal = 0.43 F Xtotal = 411.3 Ztotal = 411.3

90o or Ztotal = 0 j 411.3

Second strategy: ZC 1 = XC 1 = 535.9 YC 1 = YC 2 =

1 ZC 1

= 1.866 mS = 565.5 S = 411.3

ZC 1 = XC 2 = 1.768 k
1 ZC 2

Ytotal = 2.432 mS Ztotal =

1 Ytotal

45

Third strategy: (using complex numbers) XC 1 = 535.9 ZC1 = 535.9 90o XC 2 = 1.768 k ZC1 = 1.768 k 90o Ztotal = 411.3 90o or Ztotal = 0 j 411.3 Answer 22

Phasor diagram
L1 100m L2 100m

Ztotal = 2.890 k

XL1 = 1.445 k XL2 = 1.445 k

Phasor diagram
L1 100m R1 1k5

Ztotal = 2.083 k

XL1 = 1.445 k R1 = 1.5 k

46

Answer 23

Phasor diagram
100m L1 100m L2

BL1 = 692 S Ztotal = 722.6 BL2 = 692 S Ytotal = 1.384 mS Phasor diagram

100m L1

1k5 R1

GR1 = 666.7 S Ztotal = 1.041 k BL1 = 692 S Ytotal = 960.9 S

Challenge question: why are the susceptance vectors (BL1 and BL2 ) pointed down instead of up as impedance vectors for inductances typically are? Answer 24 IL = 530.5 A RMS IR = 490.2 A RMS Itotal = 722.3 A RMS Ztotal = 3.461 k Answer 25 I = 3.732206 mA I = 3.732212 mA not? Follow-up question #2: explain how the ESR of a capacitor can lead to physical heating of the component, especially under high-voltage, high-frequency conditions. What safety concerns might arise as a result of this? Answer 26 VL = 12.60 volts RMS VR = 8.137 volts RMS I = 11.46 milliamps RMS

89.89o for the real capacitor with ESR. 90.00o for the ideal capacitor.

Follow-up question #1: can this ESR be detected by a DC meter check of the capacitor? Why or why

47

Answer 27 VL = 13.04 volts RMS VR = 20.15 volts RMS I = 4.030 milliamps RMS Z = 32.91o Answer 28 VC = 14.39 volts RMS VR = 4.248 volts RMS I = 903.9 A RMS Follow-up question: identify the consequences of a shorted capacitor in this circuit, with regard to circuit current and component voltage drops. Answer 29 VC = 47.56 volts peak VR = 6.508 volts peak I = 1.972 milliamps peak Z = 82.21o Follow-up question: what would we have to do to get these answers in units RMS instead of units peak? Answer 30 Inductors are reactive rather than resistive components, and therefore do not dissipate power (ideally).

Ztotal Ztotal Rload

XL(series)

XL(series) Rload

Follow-up question: the inductive circuit is not just more energy-ecient it is safer as well. Identify a potential safety hazard that the resistive power-control circuit poses due to the energy dissipation of its variable resistor.

48

Answer 31 Ill let you gure out how to explain the operation of this test setup. The formula you would use looks like this: Cx = 1 2f R

Follow-up question: could you use a similar setup to measure the inductance of an unknown inductor Lx ? Why or why not? Challenge question: astute observers will note that this setup might not work in real life because the ground connection of the oscilloscope is not common with one of the function generators leads. Explain why this might be a problem, and suggest a practical solution for it. Answer 32 Isupply = 12.29 A Answer 33 Leq = 61.11 mH Answer 34

0.5 H 470 290 Hz

200 mH 1.5 k

100 Hz

Ztotal = 565.3 33.76o

1H Ztotal = 2.652 k 55.55o

100 Hz

0.5 H Ztotal = 261.2 56.24o

470

0.2 H 290 Hz 1H Ztotal = 297.6 78.55o

1.5 k

Answer 35 = 81 degrees Suppose the lamp turned on whenever the pushbutton switch was actuated, but the doorbell refused to ring. Identify what you think to be the most likely fault which could account for this problem.

49

Answer 36 I = 56.548671 mA I = 56.548668 mA Answer 37 Vout = 1.754 V 0o 89.98o for the real capacitor with leakage resistance. 90.00o for the ideal capacitor.

Follow-up question #1: explain why the division ratio of a capacitive voltage divider remains constant with changes in signal frequency, even though we know that the reactance of the capacitors (XC 1 and XC 2 ) will change. Follow-up question #2: one interesting feature of capacitive voltage dividers is that they harbor the possibility of electric shock after being disconnected from the voltage source, if the source voltage is high enough and if the disconnection happens at just the right time. Explain why a capacitive voltage divider poses this threat whereas a resistive voltage divider does not. Also, identify what the time of disconnection from the AC voltage source has to do with shock hazard. Answer 38 The proper angle in this circuit is , and it will be a positive (leading) quantity. Answer 39 Vout = 6.7 V Answer 40 Vout = 2.593 V -47.9o

61.3o

Answer 41 EC phase shift = -76.7o Challenge question: what eect will a change in potentiometer setting have on this phase angle? Specically, will increasing the resistance make the phase shift approach -90o or approach 0o ? Answer 42 f = 798 Hz Answer 43 f = 6.54 kHz Answer 44 f = 465 Hz Answer 45 f = 929 Hz Answer 46 f = 11.342 kHz f= R 2L tan

50

Answer 47 R = 6.826 k R = 2f L tan Answer 48 f = 2.804 kHz f = Answer 49 R = 2.902 k R= Answer 50 f = 2.143 kHz f= Answer 51 R = 669.7 R= 1 2f C tan 1 2RC tan 2f L tan R tan 2L

Answer 52 R = 16.734 k R= Answer 53 Vout = R Vin

1 2f C 2

tan 2f C

+ R2

Answer 54 Vout = R Vin

C1 +C2 2f C1 C2 2

+ R2

51

Answer 55 Itotal = 0.895 mA VL1 = 9.14 V VL2 = 2.19 V VR1 = 6.08 V VR2 = 1.07 V = 57.71o

I suggest using a dual-trace oscilloscope to measure total voltage (across the supply terminals) and voltage drop across resistor R2 . Theoretically, measuring the voltage dropped by either resistor would be ne, but R2 works better for practical reasons (oscilloscope input lead grounding). Phase shift then could be measured either in the time domain or by a Lissajous gure analysis. Answer 56 Itotal = 2.12 mA IL1 = 581 A IL2 = 1.07 mA IR1 = 597 A IR2 = 730 A = 51.24o

Measuring with an oscilloscope requires the addition of a shunt resistor into this circuit, because oscilloscopes are (normally) only able to measure voltage, and there is no phase shift between any voltages in this circuit because all components are in parallel. I leave it to you to suggest where to insert the shunt resistor, what resistance value to select for the task, and how to connect the oscilloscope to the modied circuit. Answer 57 Itotal = 2.269 mA VC 1 = 3.041 V VC 2 = 5.354 V VR1 = 15.43 V VR2 = 2.723 V = 24.82o (voltage lagging current)

I suggest using a dual-trace oscilloscope to measure total voltage (across the supply terminals) and voltage drop across resistor R2 . Theoretically, measuring the voltage dropped by either resistor would be ne, but R2 works better for practical reasons (oscilloscope input lead grounding). Phase shift then could be measured either in the time domain or by a Lissajous gure analysis. Answer 58 VC1 = 0.921 V VC2 = 0.921 V VR1 = 1.184 V

52.11o 52.11o 37.90o

Follow-up question: how much phase shift is there between the capacitors voltage drop and the resistors voltage drop? Explain why this value is what it is.

52

Answer 59 = 26.51o Challenge question: explain how the following phasor diagram was determined for this problem:

2.0 8V

7V 4.126.51
o

4.66 V

Answer 60 Itotal = 3.61 amps peak or 2.55 amps RMS Answer 61

3.3 F

0.1 F

100 Hz

470

290 Hz

1.5 k

Ztotal = 673.4 -45.74o

0.22 F Ztotal = 8.122 k -79.36o

3.3 F 100 Hz Ztotal = 336.6 -44.26o

470

0.1 F

0.22 F

290 Hz Ztotal = 1.129 k -41.17o

1.5 k

53

Answer 62

R1 470

3.3 F

C1

17 V 60 Hz

R1 V I Z
Answer 63 C = 562.2 nF Answer 64 Zinput = 52.98 k at 150 kHz

C1 17 V 0o 21.15 mA 90o 803.8 -90o

Total 17 V 0o 41.9 mA 30.3o 405.7 -30.3o

17 V 0o 36.17 mA 0o 470 0o

Follow-up question: what are the respective input impedances for ideal voltmeters and ideal ammeters? Explain why each ideal instrument needs to exhibit these impedances in order to accurately measure voltage and current (respectively) with the least impact to the circuit under test. Answer 65 I (R) = 0o I (C ) = 90o I (total) = some positive angle between 0o and 90o , exclusive Answer 66 Ztotal = 13

-90o

Follow-up question: does this circuit appear to be inductive or capacitive from the sources point of view? Answer 67 Ztotal = R2 + (XL XC )2

Answer 68 Overall, the rst (series) circuits behavior is inductive. The second (parallel) circuits behavior, though, is capacitive. Follow-up question: which component dominates the behavior of a series LC circuit, the one with the least reactance or the one with the greatest reactance? Which component dominates the behavior of a parallel LC circuit, the one with the least reactance or the one with the greatest reactance?

54

Answer 69 f = 200 Hz ; VL = 1.750 V ; VC = 11.79 V ; Vspeaker = 5.572 V f = 550 Hz ; VL = 6.472 V ; VC = 5.766 V ; Vspeaker = 7.492 V f = 900 Hz ; VL = 9.590 V ; VC = 3.763 V ; Vspeaker = 6.783 V This circuit is known as a midrange crossover in stereo system design. Answer 70 A 1132.1 resistor connected in series with a 269.6 nF capacitor would suce. Answer 71 Ytotal =

G2 + (BL BC )2 26.98o

Answer 72 Ztotal = 8.911 k Answer 73 Rparallel = 13.16 Lparallel = 51.75 mH

Challenge question: in the parallel LR circuit, the resistor will dissipate a lot of energy in the form of heat. Does this mean that the electric motor, which is electrically equivalent to the LR network, will dissipate the same amount of heat? Explain why or why not. Answer 74 Ztotal = 1.18 k

50.54o

If connected in parallel: R = 1.857 k ; L = 243.3 mH. Hint: if you are having diculty guring out where to start in answering this question, consider the fact that these two circuits, if equivalent in total impedance, will draw the exact same amount of current from a common AC source at 1 kHz. Answer 75 Let the electrons themselves give you the answers to your own practice problems!

55

Notes Notes 1 After discussing alternative possibilities with your students, shift the discussion to one on how likely any of these failures are. For instance, how likely is it that the solenoid coil has developed an open fault compared to the likelihood of a regular wire connection going bad in the circuit? How do either of these possibilities compare with the likelihood of the source failing as a result of a tripped circuit breaker or other power outage? Notes 2 The purpose of this question is to get students to realize that any way they can calculate total impedance is correct, whether calculating total inductance and then calculating impedance from that, or by calculating the impedance of each inductor and then combining impedances to nd a total impedance. This should be reassuring, because it means students have a way to check their work when analyzing circuits such as this! Notes 3 A common misconception many students have about capacitive reactances and impedances is that they must interact oppositely to how one would normally consider electrical opposition. That is, many students believe capacitive reactances and impedances should add in parallel and diminish in series, because thats what capacitance (in Farads) does! This is not true, however. Impedances always add in series and diminish in parallel, at least from the perspective of complex numbers. This is one of the reasons I favor AC circuit calculations using complex numbers: because then students may conceptually treat impedance just like they treat DC resistance. The purpose of this question is to get students to realize that any way they can calculate total impedance is correct, whether calculating total capacitance and then calculating impedance from that, or by calculating the impedance of each capacitor and then combining impedances to nd a total impedance. This should be reassuring, because it means students have a way to check their work when analyzing circuits such as this! Notes 4 Ask your students if this equation looks similar to any other mathematical equations theyve seen before. If not, square both sides of the equation so it looks like Z 2 = R2 + X 2 and ask them again. Notes 5 Ask your students if this equation looks similar to any other mathematical equations theyve seen before. If not, square both sides of the equation so it looks like Z 2 = R2 + X 2 and ask them again. Notes 6 This question has two dierent layers: rst, how to reconcile the strange voltage readings with Kirchhos Voltage Law; and second, how to experimentally validate the accuracy of the voltmeters and the fact that they are all registering the same type of voltage (RMS, peak, or otherwise, it doesnt matter). The rst layer of this question regards the basic concepts of AC phase, while the second exercises troubleshooting and critical thinking skills. Be sure to discuss both of these topics in class with your students.

56

Notes 7 I want students to see that there are two dierent ways of approaching a problem such as this: with scalar math and with complex number math. If students have access to calculators that can do complexnumber arithmetic, the complex approach is actually simpler for series-parallel combination circuits, and it yields richer (more informative) results. Ask your students to determine which of the approaches most resembles DC circuit calculations. Incidentally, this is why I tend to prefer complex-number AC circuit calculations over scalar calculations: because of the conceptual continuity between AC and DC. When you use complex numbers to represent AC voltages, currents, and impedances, almost all the rules of DC circuits still apply. The big exception, of course, is calculations involving power. Notes 8 Inductors are the least pure of any reactive component, due to signicant quantities of resistance in the windings. Discuss this fact with your students, and what it means with reference to choosing inductors versus capacitors in circuit designs that could use either. Notes 9 Nothing special to note here, just practice with the impedance triangle (and the capacitive reactance formula). Notes 10 I want students to see that there are two dierent ways of approaching a problem such as this: with scalar math and with complex number math. If students have access to calculators that can do complexnumber arithmetic, the complex approach is actually simpler for series-parallel combination circuits, and it yields richer (more informative) results. Ask your students to determine which of the approaches most resembles DC circuit calculations. Incidentally, this is why I tend to prefer complex-number AC circuit calculations over scalar calculations: because of the conceptual continuity between AC and DC. When you use complex numbers to represent AC voltages, currents, and impedances, almost all the rules of DC circuits still apply. The big exception, of course, is calculations involving power. Notes 11 Ask your students how they were able to make the determination of greater voltage drop. Which method yields the fastest solution (i.e. requires the fewest steps)? Notes 12 This would be an excellent question to have students present methods of solution for. Sometimes I have students present nothing but their solution steps on the board in front of class (no arithmetic at all), in order to generate a discussion on problem-solving strategies. The important part of their education here is not to arrive at the correct answer or to memorize an algorithm for solving this type of problem, but rather how to think like a problem-solver, and how to methodically apply the math they know to the problem(s) at hand. Notes 13 Ask your students if this equation looks familiar to them. It should! The answer to the second follow-up question is a matter of algebraic substitution. Work through this process with your students, and then ask them to compare the resulting equation with other equations theyve seen before. Does its form look familiar to them in any way?

57

Notes 14 Ask your students if this equation looks familiar to them. It should! The answer to the challenge question is a matter of algebraic substitution. Work through this process with your students, and then ask them to compare the resulting equation with other equations theyve seen before. Does its form look familiar to them in any way? Notes 15 This question is set up to be more complex than it has to be. Its purpose is to get students thinking in terms of parallel admittances, in a manner similar to parallel conductances. Notes 16 This question is another example of how multiple means of calculation will give you the same answer (if done correctly!). Make note to your students that this indicates an answer-checking strategy! Notes 17 Some students may wonder why every side of the triangle is represented by a Y term, rather than Y for the hypotenuse, G for the adjacent, and B for the opposite. If students ask about this, remind them that conductance (G) and susceptance (B ) are simple two dierent types of admittances (Y ), just as resistance (R) and reactance (X ) are simply two dierent types of impedances (Z ). Notes 18 Some electronics textbooks (and courses) tend to emphasize scalar impedance calculations, while others emphasize complex number calculations. While complex number calculations provide more informative results (a phase shift given in every variable!) and exhibit conceptual continuity with DC circuit analysis (same rules, similar formulae), the scalar approach lends itself better to conditions where students do not have access to calculators capable of performing complex number arithmetic. Yes, of course, you can do complex number arithmetic without a powerful calculator, but its a lot more tedious and prone to errors than calculating with admittances, susceptances, and conductances (primarily because the phase shift angle is omitted for each of the variables). Notes 19 The purpose of this question is to get students to realize that any way they can calculate total impedance is correct, whether calculating total inductance and then calculating impedance from that, or by calculating the impedance of each inductor and then combining impedances to nd a total impedance. This should be reassuring, because it means students have a way to check their work when analyzing circuits such as this! Notes 20 Some electronics textbooks (and courses) tend to emphasize scalar impedance calculations, while others emphasize complex number calculations. While complex number calculations provide more informative results (a phase shift given in every variable!) and exhibit conceptual continuity with DC circuit analysis (same rules, similar formulae), the scalar approach lends itself better to conditions where students do not have access to calculators capable of performing complex number arithmetic. Yes, of course, you can do complex number arithmetic without a powerful calculator, but its a lot more tedious and prone to errors than calculating with admittances, susceptances, and conductances (primarily because the phase shift angle is omitted for each of the variables).

58

Notes 21 A common misconception many students have about capacitive reactances and impedances is that they must interact oppositely to how one would normally consider electrical opposition. That is, many students believe capacitive reactances and impedances should add in parallel and diminish in series, because thats what capacitance (in Farads) does! This is not true, however. Impedances always add in series and diminish in parallel, at least from the perspective of complex numbers. This is one of the reasons I favor AC circuit calculations using complex numbers: because then students may conceptually treat impedance just like they treat DC resistance. The purpose of this question is to get students to realize that any way they can calculate total impedance is correct, whether calculating total capacitance and then calculating impedance from that, or by calculating the impedance of each capacitor and then combining impedances to nd a total impedance. This should be reassuring, because it means students have a way to check their work when analyzing circuits such as this! Notes 22 Phasor diagrams are powerful analytical tools, if one knows how to draw and interpret them. With hand calculators being so powerful and readily able to handle complex numbers in either polar or rectangular form, there is temptation to avoid phasor diagrams and let the calculator handle all the angle manipulation. However, students will have a much better understanding of phasors and complex numbers in AC circuits if you hold them accountable to representing quantities in that form. Notes 23 Phasor diagrams are powerful analytical tools, if one knows how to draw and interpret them. With hand calculators being so powerful and readily able to handle complex numbers in either polar or rectangular form, there is temptation to avoid phasor diagrams and let the calculator handle all the angle manipulation. However, students will have a much better understanding of phasors and complex numbers in AC circuits if you hold them accountable to representing quantities in that form. Notes 24 This would be an excellent question to have students present methods of solution for. Sometimes I have students present nothing but their solution steps on the board in front of class (no arithmetic at all), in order to generate a discussion on problem-solving strategies. The important part of their education here is not to arrive at the correct answer or to memorize an algorithm for solving this type of problem, but rather how to think like a problem-solver, and how to methodically apply the math they know to the problem(s) at hand. Notes 25 Although capacitors do contain their own parasitic eects, ESR being one of them, they still tend to be much purer components than inductors for general use. This is another reason why capacitors are generally favored over inductors in applications where either will suce.

59

Notes 26 Nothing special here just a straightforward exercise in series AC circuit calculations. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. The following is a sample of a written problem-solving strategy for analyzing a series resistive-reactive AC circuit: Step Step Step Step Step 1: 2: 3: 4: 5: Calculate all reactances (X ). Draw an impedance triangle (Z ; R ; X ), solving for Z Calculate circuit current using Ohms Law: I = V Z Calculate series voltage drops using Ohms Law: V = IZ Check work by drawing a voltage triangle (Vtotal ; V1 ; V2 ), solving for Vtotal

By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made. Notes 27 Nothing special here just a straightforward exercise in series AC circuit calculations. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. The following is a sample of a written problem-solving strategy for analyzing a series resistive-reactive AC circuit: Step Step Step Step Step 1: 2: 3: 4: 5: Calculate all reactances (X ). Draw an impedance triangle (Z ; R ; X ), solving for Z Calculate circuit current using Ohms Law: I = V Z Calculate series voltage drops using Ohms Law: V = IZ Check work by drawing a voltage triangle (Vtotal ; V1 ; V2 ), solving for Vtotal

By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made.

60

Notes 28 Nothing special here just a straightforward exercise in series AC circuit calculations. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. The following is a sample of a written problem-solving strategy for analyzing a series resistive-reactive AC circuit: Step Step Step Step Step 1: 2: 3: 4: 5: Calculate all reactances (X ). Draw an impedance triangle (Z ; R ; X ), solving for Z Calculate circuit current using Ohms Law: I = V Z Calculate series voltage drops using Ohms Law: V = IZ Check work by drawing a voltage triangle (Vtotal ; V1 ; V2 ), solving for Vtotal

By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made. Notes 29 Bring to your students attention the fact that total voltage in this circuit is given in peak units rather than RMS, and what eect this has on our answers. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. The following is a sample of a written problem-solving strategy for analyzing a series resistive-reactive AC circuit: Step Step Step Step Step 1: 2: 3: 4: 5: Calculate all reactances (X ). Draw an impedance triangle (Z ; R ; X ), solving for Z Calculate circuit current using Ohms Law: I = V Z Calculate series voltage drops using Ohms Law: V = IZ Check work by drawing a voltage triangle (Vtotal ; V1 ; V2 ), solving for Vtotal

By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made. Notes 30 If appropriate, you may want to mention devices called saturable reactors, which are used to control power in AC circuits by the exact same principle: varying a series inductance. Notes 31 This method of measuring capacitance (or inductance for that matter) is fairly old, and works well if the unknown component has a high Q value.

61

Notes 32 This is a practical example of a parallel LR circuit, as well as an example of how complex electrical devices may be modeled by collections of ideal components. To be honest, a loaded AC motors characteristics are quite a bit more complex than what the parallel LR model would suggest, but at least its a start! Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. The following is a sample of a written problem-solving strategy for analyzing a series resistive-reactive AC circuit: Step Step Step Step Step 1: 2: 3: 4: 5: Calculate all reactances (X ). Draw an impedance triangle (Z ; R ; X ), solving for Z Calculate circuit current using Ohms Law: I = V Z Calculate series voltage drops using Ohms Law: V = IZ Check work by drawing a voltage triangle (Vtotal ; V1 ; V2 ), solving for Vtotal

By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made. Notes 33 Here is a case where scalar calculations (R, G, X, B, Y) are much easier than complex number calculations (all Z) would be. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. The following is a sample of a written problem-solving strategy for analyzing a series resistive-reactive AC circuit: Step Step Step Step Step 1: 2: 3: 4: 5: Calculate all reactances (X ). Draw an impedance triangle (Z ; R ; X ), solving for Z Calculate circuit current using Ohms Law: I = V Z Calculate series voltage drops using Ohms Law: V = IZ Check work by drawing a voltage triangle (Vtotal ; V1 ; V2 ), solving for Vtotal

By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made. Notes 34 Have your students explain how they solved for each impedance, step by step. You may nd dierent approaches to solving the same problem(s), and your students will benet from seeing the diversity of solution techniques.

62

Notes 35 This would be an excellent question to have students present methods of solution for. Sometimes I have students present nothing but their solution steps on the board in front of class (no arithmetic at all), in order to generate a discussion on problem-solving strategies. The important part of their education here is not to arrive at the correct answer or to memorize an algorithm for solving this type of problem, but rather how to think like a problem-solver, and how to methodically apply the math they know to the problem(s) at hand. Notes 36 Discuss with your students the fact that electrolytic capacitors typically have more leakage (less Rleakage ) than most other capacitor types, due to the thinness of the dielectric oxide layer. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. The following is a sample of a written problem-solving strategy for analyzing a series resistive-reactive AC circuit: Step Step Step Step Step 1: 2: 3: 4: 5: Calculate all reactances (X ). Draw an impedance triangle (Z ; R ; X ), solving for Z Calculate circuit current using Ohms Law: I = V Z Calculate series voltage drops using Ohms Law: V = IZ Check work by drawing a voltage triangle (Vtotal ; V1 ; V2 ), solving for Vtotal

By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made. Notes 37 Capacitive voltage dividers nd use in high-voltage AC instrumentation, due to some of the advantages they exhibit over resistive voltage dividers. Your students should take special note of the phase angle for the capacitors voltage drop. Why it is 0 degrees, and not some other angle? Notes 38 Too many students blindly use impedance and voltage triangles without really understand what they are and why they work. These same students will have no idea how to approach a problem like this. Work with them to help them understand! Notes 39 This is a very practical application of resistor-capacitor (RC) circuits: to introduce a phase shift to an AC signal. Examples of where a circuit such as this may be used include oscillators (to introduce phase shift into a feedback network for a total phase shift of 360o ) and thyristor ring control circuits (phase-shifting the triggering voltage in relation to the source voltage). Notes 40 This is a very practical application of resistor-capacitor (RC) circuits: to introduce a phase shift to an AC signal. Examples of where a circuit such as this may be used include oscillators (to introduce phase shift into a feedback network for a total phase shift of 360o ) and thyristor ring control circuits (phase-shifting the triggering voltage in relation to the source voltage).

63

Notes 41 In this question, I purposely omitted any reference to voltage levels, so the students would have to set up part of the problem themselves. The goal here is to build problem-solving skills. Notes 42 Phase-shifting circuits are very useful, and important to understand. They are particularly important in some types of oscillator circuits, which rely on RC networks such as this to provide certain phase shifts to sustain oscillation. Notes 43 Phase-shifting circuits are very useful, and important to understand. They are particularly important in some types of oscillator circuits, which rely on RC networks such as this to provide certain phase shifts to sustain oscillation. Notes 44 Phase-shifting circuits are very useful, and important to understand. They are particularly important in some types of oscillator circuits, which rely on RC networks such as this to provide certain phase shifts to sustain oscillation. Notes 45 Phase-shifting circuits are very useful, and important to understand. They are particularly important in some types of oscillator circuits, which rely on RC networks such as this to provide certain phase shifts to sustain oscillation. Notes 46 Discuss with your students what a good procedure might be for calculating the unknown values in this problem, and also how they might check their work. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made.

64

Notes 47 Discuss with your students what a good procedure might be for calculating the unknown values in this problem, and also how they might check their work. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made. Notes 48 Discuss with your students what a good procedure might be for calculating the unknown values in this problem, and also how they might check their work. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made. Notes 49 Discuss with your students what a good procedure might be for calculating the unknown values in this problem, and also how they might check their work. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made.

65

Notes 50 Discuss with your students what a good procedure might be for calculating the unknown values in this problem, and also how they might check their work. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made. Notes 51 Discuss with your students what a good procedure might be for calculating the unknown values in this problem, and also how they might check their work. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made. Notes 52 Discuss with your students what a good procedure might be for calculating the unknown values in this problem, and also how they might check their work. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made.

66

Notes 53 Discuss with your students what a good procedure might be for calculating the unknown values in this problem, and also how they might check their work. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made. Notes 54 Discuss with your students what a good procedure might be for calculating the unknown values in this problem, and also how they might check their work. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made.

67

Notes 55 Some students many wonder what type of numerical result best corresponds to a multimeters readings, if they do their calculations using complex numbers (do I use polar or rectangular form, and if rectangular do I use the real or the imaginary part?). The answers given for this question should clarify that point. It is very important that students know how to apply this knowledge of AC circuit analysis to real-world situations. Asking students to determine how they would connect an oscilloscope to the circuit to measure is an exercise in developing their abstraction abilities between calculations and actual circuit scenarios. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. The following is a sample of a written problem-solving strategy for analyzing a series resistive-reactive AC circuit: Step Step Step Step Step 1: 2: 3: 4: 5: Calculate all reactances (X ). Draw an impedance triangle (Z ; R ; X ), solving for Z Calculate circuit current using Ohms Law: I = V Z Calculate series voltage drops using Ohms Law: V = IZ Check work by drawing a voltage triangle (Vtotal ; V1 ; V2 ), solving for Vtotal

By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made.

68

Notes 56 Some students many wonder what type of numerical result best corresponds to a multimeters readings, if they do their calculations using complex numbers (do I use polar or rectangular form, and if rectangular do I use the real or the imaginary part?). The answers given for this question should clarify that point. It is very important that students know how to apply this knowledge of AC circuit analysis to real-world situations. Asking students to determine how they would connect an oscilloscope to the circuit to measure is an exercise in developing their abstraction abilities between calculations and actual circuit scenarios. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. The following is a sample of a written problem-solving strategy for analyzing a series resistive-reactive AC circuit: Step Step Step Step Step 1: 2: 3: 4: 5: Calculate all reactances (X ). Draw an impedance triangle (Z ; R ; X ), solving for Z Calculate circuit current using Ohms Law: I = V Z Calculate series voltage drops using Ohms Law: V = IZ Check work by drawing a voltage triangle (Vtotal ; V1 ; V2 ), solving for Vtotal

By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made.

69

Notes 57 Some students many wonder what type of numerical result best corresponds to a multimeters readings, if they do their calculations using complex numbers (do I use polar or rectangular form, and if rectangular do I use the real or the imaginary part?). The answers given for this question should clarify that point. It is very important that students know how to apply this knowledge of AC circuit analysis to real-world situations. Asking students to determine how they would connect an oscilloscope to the circuit to measure is an exercise in developing their abstraction abilities between calculations and actual circuit scenarios. It is noteworthy that the low capacitances shown here approach parasitic capacitances between circuit board traces. In other words, whoever designs a circuit to operate at 950 kHz cannot simply place components at will on the board, but must consider the traces themselves to be circuit elements (both capacitive and inductive in nature!). The calculations used to obtain the given answers, of course, assume ideal conditions where the PC board is not considered to possess capacitance or inductance. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. The following is a sample of a written problem-solving strategy for analyzing a series resistive-reactive AC circuit: Step Step Step Step Step 1: 2: 3: 4: 5: Calculate all reactances (X ). Draw an impedance triangle (Z ; R ; X ), solving for Z Calculate circuit current using Ohms Law: I = V Z Calculate series voltage drops using Ohms Law: V = IZ Check work by drawing a voltage triangle (Vtotal ; V1 ; V2 ), solving for Vtotal

By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made.

70

Notes 58 The rst challenge of this question is for students to gure out how to reduce this series-parallel combination to something simpler. Fortunately, this is very easy to do if one remembers the properties of parallel capacitances. Students may be surprised to discover the phase shift between VC and VR is the value it is. However, this should not remain a mystery. Discuss this with your class, taking time for all of them to understand why the voltage phasors of a resistor and a capacitor in a simple series circuit will always be orthogonal. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. The following is a sample of a written problem-solving strategy for analyzing a series resistive-reactive AC circuit: Step Step Step Step Step 1: 2: 3: 4: 5: Calculate all reactances (X ). Draw an impedance triangle (Z ; R ; X ), solving for Z Calculate circuit current using Ohms Law: I = V Z Calculate series voltage drops using Ohms Law: V = IZ Check work by drawing a voltage triangle (Vtotal ; V1 ; V2 ), solving for Vtotal

By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made. Notes 59 This is an interesting question for a couple of reasons. First, students must determine how they will measure phase shift with just the two voltage indications shown by the meters. This may present a signicant challenge for some. Discuss problem-solving strategies in class so that students understand how and why it is possible to determine . Secondly, this is an interesting question because it shows how something as abstract as phase angle can be measured with just a voltmeter no oscilloscope required! Not only that, but we dont even have to know the component values either! Note that this technique works only for simple circuits. A practical point to mention here is that multimeters have frequency limits which must be considered when taking measurements on electronic circuits. Some high-quality handheld digital meters have frequency limits of hundred of kilohertz, while others fail to register accurately at only a few thousand hertz. Unless we knew these two digital voltmeters were sucient for measuring at the signal frequency, their indications would be useless to us. Notes 60 This is a really simple trigonometry problem, disguised by the necessity of having to interpret the oscilloscope display. Notes 61 Have your students explain how they solved for each impedance, step by step. You may nd dierent approaches to solving the same problem(s), and your students will benet from seeing the diversity of solution techniques.

71

Notes 62 Ask your students to share their problem-solving techniques for this question: how they solved for each parameter and in what order they performed the calculations. Notes 63 Have your students explain how they solved for each impedance, step by step. You may nd dierent approaches to solving the same problem(s), and your students will benet from seeing the diversity of solution techniques. Notes 64 Mention to your students that this capacitive loading eect only gets worse when a cable is attached to the oscilloscope input. The calculation performed for this question is only for the input of the oscilloscope itself, not including whatever capacitance may be included in the test probe cable! This is one of the reasons why 10 probes are used with oscilloscopes: to minimize the loading eect on the tested circuit. Notes 65 Some students will be confused about the positive phase angles, since this is a capacitive circuit and they have learned to associate negative angles with capacitors. It is important for these students to realize, though, that the negative angles they immediately associate with capacitors are in reference to impedance and not necessarily to other variables in the circuit! Notes 66 Here, the complementary nature of inductive and capacitive reactances is plain to see: they subtract in series. Challenge your students by asking them what the total impedance of this circuit would be if the two reactances were equal. Notes 67 Ask your students why one of the reactance terms under the radicand is positive and the other is negative. The way this equation is written, does it matter which term is negative? As your students if we would obtain the same answer if it were written as Ztotal = R2 + (XC XL )2 instead. Challenge them to answer this question without using a calculator!

72

Notes 68 As usual, the real point of this question is to get students to think about the analytical procedure(s) they use, and to engage their minds in problem-solving behavior. Ask them why they think the circuits behave inductively or capacitively. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. The following is a sample of a written problem-solving strategy for analyzing a series resistive-reactive AC circuit: Step Step Step Step Step 1: 2: 3: 4: 5: Calculate all reactances (X ). Draw an impedance triangle (Z ; R ; X ), solving for Z Calculate circuit current using Ohms Law: I = V Z Calculate series voltage drops using Ohms Law: V = IZ Check work by drawing a voltage triangle (Vtotal ; V1 ; V2 ), solving for Vtotal

By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made. Notes 69 This is an interesting circuit to analyze. Note how, out of the three frequency points we performed calculations at, the speakers voltage is greatest at the middle frequency. Note also how the inductor and capacitor drop very disparate amounts of voltage at the high and low frequencies. Discuss this circuits behavior with your students, and ask them what practical function this circuit performs. Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. The following is a sample of a written problem-solving strategy for analyzing a series resistive-reactive AC circuit: Step Step Step Step Step 1: 2: 3: 4: 5: Calculate all reactances (X ). Draw an impedance triangle (Z ; R ; X ), solving for Z Calculate circuit current using Ohms Law: I = V Z Calculate series voltage drops using Ohms Law: V = IZ Check work by drawing a voltage triangle (Vtotal ; V1 ; V2 ), solving for Vtotal

By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made.

73

Notes 70 As usual, the most important part of your students answers is not the gures themselves, but rather their methods of solution. Students should be very familiar with how to calculate the impedance of a series-connected group of components, but calculating component values from an impedance gure may be a challenge to some. Notes 71 Ask your students why one of the reactance terms under the radicand is positive and the other is negative. The way this equation is written, does it matter which term is negative? Ask your students if we would obtain the same answer if the equation were written as Ytotal = G2 + (BC BL )2 instead. Challenge them to answer this question without using a calculator! Notes 72 Ask your students how they obtained the phase angle for this circuit. There is more than one way to calculate this! Students often have diculty formulating a method of solution: determining what steps to take to get from the given conditions to a nal answer. While it is helpful at rst for you (the instructor) to show them, it is bad for you to show them too often, lest they stop thinking for themselves and merely follow your lead. A teaching technique I have found very helpful is to have students come up to the board (alone or in teams) in front of class to write their problem-solving strategies for all the others to see. They dont have to actually do the math, but rather outline the steps they would take, in the order they would take them. The following is a sample of a written problem-solving strategy for analyzing a series resistive-reactive AC circuit: Step Step Step Step Step 1: 2: 3: 4: 5: Calculate all reactances (X ). Draw an impedance triangle (Z ; R ; X ), solving for Z Calculate circuit current using Ohms Law: I = V Z Calculate series voltage drops using Ohms Law: V = IZ Check work by drawing a voltage triangle (Vtotal ; V1 ; V2 ), solving for Vtotal

By having students outline their problem-solving strategies, everyone gets an opportunity to see multiple methods of solution, and you (the instructor) get to see how (and if!) your students are thinking. An especially good point to emphasize in these open thinking activities is how to check your work to see if any mistakes were made. Notes 73 If students get stuck on the challenge question, remind them that an electric motor does mechanical work, which requires energy. Notes 74 This is an interesting question, requiring the student to think creatively about how to convert one conguration of circuit into another, while maintaining the same total eect. As usual, the real purpose of a question like this is to develop problem-solving strategies, rather than to simply obtain an answer.

74

Notes 75 It has been my experience that students require much practice with circuit analysis to become procient. To this end, instructors usually provide their students with lots of practice problems to work through, and provide answers for students to check their work against. While this approach makes students procient in circuit theory, it fails to fully educate them. Students dont just need mathematical practice. They also need real, hands-on practice building circuits and using test equipment. So, I suggest the following alternative approach: students should build their own practice problems with real components, and try to mathematically predict the various voltage and current values. This way, the mathematical theory comes alive, and students gain practical prociency they wouldnt gain merely by solving equations. Another reason for following this method of practice is to teach students scientic method: the process of testing a hypothesis (in this case, mathematical predictions) by performing a real experiment. Students will also develop real troubleshooting skills as they occasionally make circuit construction errors. Spend a few moments of time with your class to review some of the rules for building circuits before they begin. Discuss these issues with your students in the same Socratic manner you would normally discuss the worksheet questions, rather than simply telling them what they should and should not do. I never cease to be amazed at how poorly students grasp instructions when presented in a typical lecture (instructor monologue) format! An excellent way to introduce students to the mathematical analysis of real circuits is to have them rst determine component values (L and C) from measurements of AC voltage and current. The simplest circuit, of course, is a single component connected to a power source! Not only will this teach students how to set up AC circuits properly and safely, but it will also teach them how to measure capacitance and inductance without specialized test equipment. A note on reactive components: use high-quality capacitors and inductors, and try to use low frequencies for the power supply. Small step-down power transformers work well for inductors (at least two inductors in one package!), so long as the voltage applied to any transformer winding is less than that transformers rated voltage for that winding (in order to avoid saturation of the core). A note to those instructors who may complain about the wasted time required to have students build real circuits instead of just mathematically analyzing theoretical circuits: What is the purpose of students taking your course? If your students will be working with real circuits, then they should learn on real circuits whenever possible. If your goal is to educate theoretical physicists, then stick with abstract analysis, by all means! But most of us plan for our students to do something in the real world with the education we give them. The wasted time spent building real circuits will pay huge dividends when it comes time for them to apply their knowledge to practical problems. Furthermore, having students build their own practice problems teaches them how to perform primary research, thus empowering them to continue their electrical/electronics education autonomously. In most sciences, realistic experiments are much more dicult and expensive to set up than electrical circuits. Nuclear physics, biology, geology, and chemistry professors would just love to be able to have their students apply advanced mathematics to real experiments posing no safety hazard and costing less than a textbook. They cant, but you can. Exploit the convenience inherent to your science, and get those students of yours practicing their math on lots of real circuits!

75