Service Bulletin: Title
Service Bulletin: Title
May 2, 2005
SB137Z
TITLE REVISED TIME BETWEEN OVERHAUL (TBO) SPECIFICATIONS TO: FAA-Approved Propeller Repair Stations, Aircraft Manufacturers, Owners and Operators MODELS AFFECTED All Propellers, Governors, and Accumulators PUBLICATIONS AFFECTED 701115, 710930, 720415, 730720, MPC400, 780401, 780630, 790901, 810301, 810915, 860201, 880415, 890119, MPC1100-[X], CMM1100-[X] REASON This revision adds C406 and C409 life limits and changes the overhaul frequency letter designation for the C406, the C409 and the C1105 in Table 1, and the overhaul frequency notes in Steps 5J, 5S, and 5T. Adds a NOTE to Steps 5M and 5N to change the blade life limits for the C1101, C1102, C1103, and C1104. Also adds overhaul frequencies for the C230, C231, C233, C234 and C235. Changes to this service bulletin, with the exception of editorial and formatting changes, are indicated by vertical lines in the margin. DESCRIPTION Service Bulletin 137Z replaces Service Bulletin 137Y dated December 1, 2003. APPROVAL FAA approval has been obtained on technical data in this publication that affects product type design. ACCOMPLISHMENT INSTRUCTIONS 1. General A. The following pages show McCauleys mandatory specied time between overhaul for propellers, governors, and accumulators. Specications are based on hours of operation and calendar time, whichever occurs rst. The starting point for the calendar limit is the date of rst installation on an engine (not from date of manufacture or overhaul). Date of manufacture or overhaul is applicable when determining long term storage inspections. If the propeller has been removed from service, the TBO calendar limit still applies, not long term storage. NOTE: Calendar month is the period of time from the rst day of a month to the last day of the month. When the term calendar month is used, compliance can be achieved at any time Original Issue: December 28, 1979 Page 1 of 12
TO OBTAIN SATISFACTORY RESULTS, PROCEDURES SPECIFIED IN THIS SERVICE INFORMATION MUST BE ACCOMPLISHED IN ACCORDANCE WITH ACCEPTED METHODS AND PREVAILING GOVERNMENT REGULATIONS. MCCAULEY PROPELLER SYSTEMS CANNOT BE RESPONSIBLE FOR THE QUALITY OF WORK PERFORMED IN ACCOMPLISHING THIS SERVICE INFORMATION. McCauley Propeller Systems PO Box 7704 Wichita, Kansas 67277-7704
COPYRIGHT 1979 McCauley Propeller Systems
SERVICE BULLETIN
SB137Z
during the month, up to and including the last day of the month. For Example: a propeller with a 60 calendar month inspection interval is inspected and approved upon any given day of the month. This propeller will become due for inspection upon the last day of the same month, 60 months later. B. C. All deviations from published TBOs must be approved by your local Regulatory Authority with a recommendation from McCauley. If the propeller, governor, or accumulator is in storage in excess of two years, additional inspections are required. Once installed on an aircraft the propeller, governor, or accumulator calendar limit is not interrupted by subsequent removal and/or storage. Propeller, governor, and accumulator overhaul should, as much as practical, coincide with engine overhaul. For example, in a case where propeller TBO is 1500 hours and engine TBO is 1400 hours, the propeller should be overhauled at the same time as the engine. This is appropriate as long as neither TBO limit is exceeded.
D.
2.
(b)
(3)
For all propeller models, If storage period exceeds ve (5) years, before entering service or returning to service perform the following inspection and parts replacement: (a) Disassemble as necessary to replace all rubber seals and lubricants. Total disassembly (such as removing ferrules from blades) is not required unless evidence of corrosion warrants further disassembly. This must be accomplished only by a FAA approved propeller repair station or international equivalent in accordance with the appropriate propeller service manual. Make logbook entry of compliance with Service Bulletin 137Y. Inspect parts for damage and corrosion, repair/replace parts as necessary. Work must be accomplished only by a FAA approved propeller repair station or international equivalent in accordance with the appropriate propeller service manual. Make logbook entry of compliance with Service Bulletin 137Y. SB137Z May 2, 2005
(b)
Page 2
SERVICE BULLETIN
SB137Z
3. Long Term Storage of Governors and Accumulators A. The following is applicable to new and overhauled governors or accumulators prior to entering service (engine installation) or at any time governor or accumulator is removed from service. Storage time is determined from date of manufacture or overhaul or removal from aircraft. (1) (2) Storage must be in a clean and dry environment, preferably in the original shipping carton and above ground level, to minimize exposure to dirt and moisture. If storage period exceeds 2 years, before entering service or returning to service, perform the following inspection: (a) (b) Inspect externally for damage and corrosion. Test run the governor on a governor test bench to verify correct operation and check for leakage. This must be accomplished only by a FAA approved governor repair station or international equivalent in accordance with the governor service manual. Pressure check accumulator to verify correct operation and check for leakage. This must be accomplished only by a FAA approved governor repair station or international equivalent in accordance with the governor service manual.
(c)
(3)
If storage period exceeds 5 years before entering service or returning to service, perform the following inspection and parts replacement:
WARNING:
COMPLETELY RELEASE ALL AIR OR NITROGEN PRESSURE BEFORE ANY DISASSEMBLY OF ACCUMULATOR. REMOVAL OF RETAINING RINGS WITH AIR PRESSURE INSIDE THE CYLINDER WILL RESULT IN EXPLOSIVE BLOW-OUT OF PARTS WITH DANGER OF SERIOUS INJURY.
(a)
Disassemble as necessary to replace all rubber seals and gaskets. Total disassembly (such as disassembling the yweight assembly) is not required unless evidence of corrosion warrants further disassembly. Inspect parts for damage and corrosion, repair/replace parts as necessary. 1 Critical inspection areas for governors are I.D. of drive gear, O.D. of the pilot spool, and "toes" of yweight. Work must be accomplished only by a FAA approved governor repair station or international equivalent in accordance with the governor service manual. Critical inspection area for accumulators is inside of cylinder for corrosion. Work must be accomplished only by a FAA approved governor repair station or international equivalent in accordance with the governor service manual.
(b)
(4)
Test run the governor on a governor test bench to verify correct operation and check for leakage. This must be accomplished only by a FAA approved governor repair station or international equivalent in accordance with the governor service manual. Pressure check accumulator to verify correct operation and check for leakage. This must be accomplished only by a FAA approved governor repair station or international equivalent in accordance with the governor service manual.
(5)
4.
Propeller Models A. The propeller model designation is impression stamped on the propeller hub. Change letters are frequently stamped at the end of the model designation (e.g. 2A34C50-BM). These letters indicate engineering changes and/or previous overhaul modications. In Table 1, unless specic change letters are shown, the overhaul frequency note applies to all propellers of that model, regardless of change letters. Use the highest letter stamped after hub model number to determine frequency of overhaul. (Refer to Step 5.)
Page 3
SERVICE BULLETIN
SB137Z
Example : Propeller model 2A36C66-ALMOR 'R' is the highest letter = TBO note C. applies Propeller model 2A36C66-AEF 'F' is the highest letter = TBO note A. applies Table 1: Propeller Models Model Designation 2A36C1 2B36C7 2D34C8 2D34C9 2AF31C10 2D34C11 B2D34C11 2D36C14 B2D34C15 B2D34C16 2A36C18 2A31C21 2A34C22 2A36C23 2AF36C26 2D36C28 2A36C29 D2AF34C30 B2A36C31 D2A36C31 C2A36C32 D2A36C33 D2A34C34 D3AF32C35 2AF36C38 2AF36C39 D2AF34C41 D2AF34C42 2A36C43 Overhaul Frequency Note A. B. B. B. A. A. A. A. A. A. A. A. A. A. A. A. A. A. A. A. A. A. A. A. A. A. A. A. A.
Page 4
SERVICE BULLETIN
SB137Z
Model Designation D2A36C45 D2AF34C46 D2AF36C48 D2A34C49 2A34C50 D2AF34C52 2D34C53-less than O 2D34C53-O or higher B2D34C53-less than O B2D34C53-O or higher D2AF34C54 2AF34C55-less than O 2AF34C55-O or higher D3AF34C56 B2E34C57 D2A34C58-less than O D2A34C58-O or higher F2A34C58 D2AF34C59 D2AF34C60 D2AF34C61-less than O D2AF34C61-O or higher D2AF34C65-less than O D2AF34C65-O or higher 2A34C66-less than P 2A34C66-P or higher D2A34C67 2AF36C68 B2D34CT69 E2A34C70-less than P E2A34C70-P or higher D2AF34C71 3AF32C72-less than N 3AF32C72-N or higher E2A34C73-less than P Overhaul Frequency Note A. A. A. A. A. A. A. C. A. C. A. A. C. A. A. A. C. A. A. A. A. C. A. C. A. C. A. A. A. A. C. A. A. C. A.
Page 5
SERVICE BULLETIN
SB137Z
Model Designation E2A34C73-P or higher 3AF34C74 3AF32C75 3A32C76 D3A32C77 D2A34C78-less than P D2A34C78-P or higher D3A32C79 D3AF32C80-less than N D3AF32C80-N or higher D2AF34C81-less than O D2AF34C81-O or higher 2A36C82 3AF34C86 3AF32C87-less than N 3AF32C87-N or higher D3AF32C87-less than N D3AF32C87-N or higher D3A32C88 2AF36C89 D3A32C90-less than N D3A32C90-N or higher D2AF34C91 3AF34C92 SAF32C93-less than N 3AF32C93-N or higher D2A34C98 2A34C201-less than C 2A34C201-C or higher 2D34C202 2A34C203-less than C 2A34C203-C or higher C2A34C204-less than C C2A34C204-C or higher B2A34C205 Overhaul Frequency Note C. A. A. A. A. A. C. A. A. C. A. C. A. A. A. C. A. C. A. A. A. C. A. A. A. C. A. C. E. D. D. E. D. E. A.
Page 6
SERVICE BULLETIN
SB137Z
Model Designation B2D34C206 B2D34C207 B2D34C208 2A34C209-less than C 2A34C209-C or higher 2A34C210 B2D34C211 B2D34C212 B2D34C213 B2D34C214 2D34C215 2A34C216 B2D34C217 B2D34C218 B2D34C219 B2D34C220 2A34C221 2A37C223-less than C 2A37C223-C or higher B2D37C224 B2A34C225 2A34C227-less than C 2A34C227-C or higher B2A37C228 B2D37C229 D2A37C230 D2A37C231 2A37C232 E2A37C233 E2A37C234 B2D34C235 C2D37C236 B2A37C238 2A34C239 2A34C240 Overhaul Frequency Note D. D. D. D. E. D. D. D. D. D. D. D. D. D. D. D. D. C. E. D. D. D. E. A. D. E. E. E. E. E. E. E. E. E. D.
Page 7
SERVICE BULLETIN
SB137Z
Model Designation 2A34C241 D2AF34C301 D2AF34C302 D2AF34C303 D2AF34C304 D2AF34C305-less than B D2AF34C305-B or higher D2AF34C306 D2AF34C307 D2AF34C308 D2AF34C310 D2AF34C312 D2AF34C314 D2AF34C315 D2AF34C317 D2AF34C318 D2AF34C320 D3A34C401 D3A34C402 D3A34C403 D3A34C404 B3D34C405 3A32C406-less than D 3A32C406-D or higher B3D32C407 D3A32C408 D3A32C409-less than D D3A32C409-D or higher D3A36C410 D3A32C411 B3D32C412 B3D34C413 B3D32C414 C3D36C415 B3D36C416 Overhaul Frequency Note E. D. D. D. D. A. D. D. D. D. D. E. E. E. E. E. E. D. D. D. D. D. S. T. D. A. S. T. D. D. D. D. D. D. D.
Page 8
SERVICE BULLETIN
SB137Z
Model Designation B3D32C417 3A32C418 B3D32C419 D3A34C420-less than D D3A34C420-D or higher B3D34C421 3A34C422 3A34C423-less than D 3A34C423-D or higher B3D36C424 B3D36C427 B3D36C428 B3D36C429 D3A36C430 B3D36C431 B3D36C432 B3D36C433 3A36C434 D3A36C435 D3A36C436 B3D36C442 D3A34C443 3FF32C501 3AF34C502 3AF34C503 3AF32C504 3AF32C505 3AF32C506 3AF32C507 3AF32C508 3AF32C509 3AF37C510 3AF32C511 3AF32C512 3AF36C514 Overhaul Frequency Note D. D. D. D. E. D. D. D. E. D. D. D. D. E. E. E. E. E. E. E. E. E. D. D. D. D. D. D. D. D. D. D. D. D. D.
Page 9
SERVICE BULLETIN
SB137Z
Model Designation 3AF32C515 3AF37C516 3AF32C521 3AF32C522 3AF32C523 3AF32C524 3AF32C525 B3DF36C526 B3DF36C527 3AF32C528 3FF34C529 3GFR34C601 3GFR34C602 4HFR34C652 4HFR34C653 4HFR34C661 4HFR34C662 4HFR34C663 4HFR34C664 4HFR34C665 3GFR34C701 3GFR34C702 3GFR34C703 3GFR34C704 4HFR34C754 4HFR34C755 4HFR34C756 4JFR34C758 4HFR34C762 4HFR34C763 4HFR34C764 4HFR34C766 4HFR34C768 4HFR34C769 4HFR34C771 Overhaul Frequency Note D. D. D. D. D. F. D. F. F. F. F. G. G. H. O. H. H. L. H. K. G. G. I. G. G. G. G. G. G. G. H. G. H. H. H.
Page 10
SERVICE BULLETIN
SB137Z
Model Designation 4HFR34C773 4HFR34C774 4HFR34C775 5JFR36C1003 5HFR34C1008 B5JFR36C1101 C5JFR36C1102 B5JFR36C1103 C5JFR36C1104 5HFR34C1105 Fixed Pitch Propellers Propeller Governors Propeller Accumulators 5. Overhaul Frequency Notes A. 1200 hours or 60 calendar months, whichever occurs rst, except: (1) All C1, C14, C18, C28, C29, C31, C32, C33 and C45 propellers with plain (no prex or sufx) blade serial numbers (00000 thru 21297) - the overhaul frequency is 1000 hours or 60 calendar months, whichever occurs rst. All 2A36C23, D2AF34C30, D3AF32C35, 2AF34C55, 3AF32C75, 3A32C76 and 2A36C82 propellers with hub serial number 71XXXX and higher - the overhaul frequency is 1500 hours or 60 calendar months, whichever occurs rst. Overhaul Frequency Note H. G. G. F. H. M. M. N. N. H. P. Q. R.
(2)
B.
1000 hours or 60 calendar months, whichever occurs rst, except: (1) All 2D34C9 propellers with hub serial number 71XXXX and higher - the overhaul frequency is 1500 hours or 60 calendar months, whichever occurs rst.
C.
1500 hours or 60 calendar months, whichever occurs rst, except: (1) Agricultural aircraft installations - the overhaul frequency is 1200 hours or 60 calendar months, whichever occurs rst.
D.
2000 hours or 72 calendar months, whichever occurs rst, except: (1) (2) Agricultural aircraft installations - the overhaul frequency is 1200 hours or 60 calendar months, whichever occurs rst. Aerobatic installations - the overhaul frequency is 1000 hours or 72 calendar months, whichever occurs rst.
E. F. G. H. I. J.
2400 hours or 72 calendar months, whichever occurs rst. 3000 hours or 72 calendar months, whichever occurs rst. 3500 hours or 72 calendar months, whichever occurs rst. 5000 hours or 72 calendar months, whichever occurs rst. 4000 hours or 72 calendar months, whichever occurs rst. 2000 hours or 72 calendar months, whichever occurs rst.
Page 11
SERVICE BULLETIN
SB137Z
K. L. M. 5000 hours or 60 calendar months, whichever occurs rst. 10,000 hour life limit on blades and hub. 5000 hours or 72 calendar months, whichever occurs rst. 16,000 hour life limit on blades. 4000 hours or 60 calendar months, whichever occurs rst. 16,800 hour life limit on blades. (1) 6000 hours or 60 calendar months, whichever occurs rst, for those propellers with serial numbers higher than 931333, and those propellers serial number 931333 and lower modied per McCauley Service Letter 1993-12. 16,800 hour life limit on blades. NOTE: Blade Life Limits have been revised. For new blade Life Limits, refer to McCauley Alert Service Bulletin ASB246, latest revision, and Federal Aviation Administration Airworthiness Directive AD 2003-17-10. N. 5000 hours or 60 calendar months, whichever occurs rst. 14,500 hour life limit on blades, 26,500 hour life limit on hub. (1) 6000 hours or 60 calendar months, whichever occurs rst, for those C1103 and C1104 propellers identied by serial number in the Airworthiness Limitations Section, section 11, of the MPC1100-[X] or section 8, of the CMM1101-[X] and installed on 1500 shp aircraft. 16,800 hour life limit on blades. NOTE: Blade Life Limits have been revised. For new blade Life Limits, refer to McCauley Alert Service Bulletin ASB246, latest revision, and Federal Aviation Administration Airworthiness Directive AD 2003-17-10. O. 5000 hours or 72 calendar months, whichever occurs rst. Only for L106FA-0 blades used in the 4HFR34C653 propeller assemblies or blades that have been installed on Jetstream Series 3200 aircraft or history unknown: (1) Blades without change letter "A" must be retired from service before December 1, 2001 or upon reaching 2400 ight hours after August 1, 2000 or 16,000 hours time since new, whichever occurs rst. Blades with change letter "A" are life limited to 16,000 hours.
(2) P.
Fixed pitch propellers - 2000 hours or 72 calendar months which ever occurs rst. Additionally, the propeller mounting bolt torque should be checked at least once per year. Propeller mounting bolts must be magnetic particle inspected per ASTM E-1444 or liquid penetrant inspected per ASTM E-1417or replaced at every overhaul. Propeller mounting bolts must be replaced whenever the propeller is involved in a blade strike as dened in Service Bulletin 176[X]. (1) 1A170E/JHA[XXXX] propellers only, installed on Aircraft Operating as Pilot Schools per 14 CFR, Part 141, must be inspected per Service Bulletin 240[X] every 1000 hours or 72 calendar months which ever occurs.
Q. R. S.
All Propeller Governors - 1800 hours or 60 calendar months, whichever occurs rst. All Propeller Accumulators - 1800 hours or 60 calendar months, whichever occurs rst. 2000 hours or 72 calendar months, 10,000 hour life limit on blades and hub, except: (1) Aerobatic installations - the overhaul frequency is 1000 hours or 72 calendar months, whichever occurs rst. 10,000 hour life limit on blades and hub.
T.
2400 hours or 72 calendar months, whichever occurs rst. 10,000 hour life limit on blades and hub, except: (1) Aerobatic installations - the overhaul frequency is 1500 hours or 72 calendar months, whichever occurs rst. 10,000 hour life limit on blades and hub.
Page 12