Warning: Inspection, Testing, Preventive Maintenance and Special Operating Instructions For Planetary Hoists
Warning: Inspection, Testing, Preventive Maintenance and Special Operating Instructions For Planetary Hoists
WARNING
CAUTION
! !
Read and understand these entire instructions BEFORE operating or servicing your BRADEN/Gearmatic
hoist. Retain these instructions for future reference. Failure to properly operate, maintain and service a
hoist may lead to loss of load control and result in property damage, serious injury or death.
i NOTE: If the oil sampling/analysis has not been performed as required, refer to the tear down
inspection section on page 3.
The user of BRADEN products is responsible for hoist inspection, testing and maintenance noted above
with frequency dependent upon the severity of the hoist duty cycle and the thoroughness of the preven-
tive maintenance program in effect.
Alternate inspection periods may be used if approved in writing by BRADEN. Those that are inter-
ested in an alternate inspection period should submit a written proposal to BRADEN that includes typical
duty cycle for the hoist along with a detailed description of the preventive maintenance program for these
hoists.
2
To provide customers with qualified outlets for hoist service and repairs, BRADEN has established author-
ized Service Centers. These Service Centers have factory trained service technicians, up-to-date service
information, extensive parts inventories, complete testing facilities, and are audited by BRADEN on a reg-
ular basis for compliance. BRADEN strongly recommends the use of BRADEN authorized Service
Centers for maintenance, repair and inspection of BRADEN/Gearmatic products. Contact the Braden
Product Support Department at 918-251-8511 for the names of current authorized Service Centers.
TEAR DOWN INSPECTION – Any Hoist that has NOT been subject to regular oil sample analysis
should undergo a tear down inspection on an annual (12 month) basis. Also, if a hoist has an
unknown history of repair and/or maintenance, it is recommended that the hoist undergo a tear down
inspection prior to it being placed into service.
A tear down inspection should include the hoist being completely disassembled, cleaned and inspected
and replacement of all worn, cracked, corroded or distorted parts such as pins, bearings, shafts, gears,
brake rotors, brake plates, drum and base. Refer to the applicable BRADEN or Gearmatic Service
Manual for more details. All seals and o-rings should be replaced during a tear down inspection.
Any deficiencies, such as those listed above shall be corrected immediately.
All of the following operations must be performed before the hoist is placed back in service:
The rebuilt hoist must be line pull tested to the rated load of the hoist (hoist rating will vary with motor,
gear ratio and drum options) with a dynamometer or equivalent measuring device. This test load should
be the maximum rating for the hoist for the specific application (at the normal hydraulic relief valve setting
for the hoist), not the reduced rating for personnel lifting.
The hoist must be dynamically tested by rotating the drum several times, in both the hoisting and lowering
directions, while under a load of at least 30% of the hoist lifting capacity. Check for smooth operation dur-
ing this procedure.
The brake should be tested per the brake test procedures on page 5.
After inspection or rebuild and testing, a new certificate for personnel handling will be issued by the
inspector/ service technician effective on the date the hoist is placed back in service.
3
PREVENTIVE MAINTENANCE AND OIL SAMPLE ANALYSIS RECOMMENDATIONS
Oil Change
The gear oil should be changed after the first 100 hours of operation and on an annual basis, at minimum,
thereafter. In severe duty applications, the gear oil should be changed every six months. Use only the
recommended type of lubricants; see service manual for details.
Proper oil sampling and analysis of the sample, is a vital part of a comprehensive preventive maintenance
program. Information obtained from the oil analysis is best utilized in conjunction with a regular program
of preventive maintenance. The early warning of abnormal wear provided by an analysis program allows
the user to substitute preventive maintenance for a far more costly and dangerous failure that may lead to
loss of load control that could result in property damage, personal injury or death. Early detection of
accelerated component wear allows the scheduling of corrective maintenance and can reduce in-opera-
tion failures and costly down time.
Prepare the hoist by cleaning the drain area and drain extension tube in order to obtain an uncontaminat-
ed sample. Operate the hoist in both directions for one to two minutes and then take the oil sample from
the drain port as soon as possible. Do not take the sample from the first oil out the drain port. Take a
sample from the mid-stream flow of the oil to obtain an accurate representation of the oil condition. After
taking an oil sample, check the oil level and add new oil as required. Refer to the applicable Braden serv-
ice manual for recommended lubricant.
WARNING
CAUTION
! !
Hot oil may cause personal injury and/or burns to unprotected skin. Make certain the oil has cooled to a
safe temperature (less than 110o F or 43o C) before taking an oil sample, changing oil or servicing the
winch.
Analysis
Iron Contaminates
501 to 800 ppm Caution - Abnormal Sample (monitor on a more frequent time line)
801 ppm & up Unacceptable - Abnormal Sample (further investigation required, tear down inspec-
tion recommended)
In all contaminate monitoring, equally important as the level of contamination, is the change in the amount
of contamination compared to previous samples.
4
BRAKE TEST PROCEDURE FOR BRADEN/Gearmatic HOISTS
All BRADEN planetary hoists have a spring applied, hydraulically released, multiple disc brake inside the
hoist housing (Gearmatic hoists have a large single brake disc). This brake holds a suspended load
when the directional control valve is in neutral, or when hydraulic power is lost. A brake clutch assembly
permits the power train and drum to rotate in the direction to lift a load, while the brake remains fully
applied. A load cannot be lowered, however, without applying hydraulic pressure to the release port and
releasing the brake.
Hoists ordered for personnel handling cranes will have a needle valve in the brake release line. They will
also have a tee in the brake release line between the needle valve and the brake release port on the
hoist. One opening in the tee is capped. With the valve closed and the cap removed from the tee, the
brake is isolated from system pressure and vented to atmosphere. The brake cannot be released under
these conditions by actuating the directional control valve.
NEEDLE VALVE
"DR" PORT ON
COUNTERBALANCE
VALVE
HOIST PORT
ON MOTOR
One purpose of the valve/tee combination is to provide a means to test the brake; the other is to provide
a means to lower a load when hydraulic power is lost.
Brake Test Procedure (Hoists Equipped With Brake Valves) - Test to be performed with minimal load
on the hoist.
Remove the lockwire on the valve handle and close the valve tightly.
Remove the plug in the tee (in the brake release circuit).
With the hydraulic power unit running, move the directional control valve handle slowly to the full open,
lowering position.
Increase the engine speed, if necessary, to bring system pressure up to the relief valve setting. The hoist
drum should remain stationary.
If the drum rotates, the hoist should be disassembled and the brake should be examined for wear. In
addition, the brake springs should be measured for correct free length in those hoists using helical com-
pression springs.
5
Replace any parts showing excessive wear, and any spring whose length is shorter than the minimum
shown in the hoist Service Manual.
Reassemble the brake and hoist and repeat the above steps.
When testing is complete, be sure to reinstall the plug in the tee, fully open the valve and replace the
lockwire.
The above procedure utilizes the hoist hydraulic motor to test the brake’s ability to resist approximately
115% of the rated hoist load.
1. Remove the lockwire on the needle valve handle and close the valve tightly.
The following procedure releases the multiple disc brake while leaving the brake valve closed. Since gear
type motors are not zero leakage devices, internal motor leakage permits the load to slowly rotate the
motor although its outlet is blocked by the closed brake valve. This procedure will NOT work if there is lit-
tle or no oil in the motor. Using properly rated pipe and fittings the standpipe described below may be
permanently installed in the hydraulic system to avoid installing one in an emergency.
WARNING
CAUTION
! !
The standpipe referred to in step (3) below MUST be used. Attempting this procedure with no oil in the
motor or with the brake valve stuck in the open position will cause the load to free fall, which could result
in property damage, personal injury or death.
3. Remove both main hoses from the motor and attach a standpipe to the motor port on the opposite
side of the motor from the brake valve. NOTE: This port may be fitted with a manifold. The stand-
pipe is simply a length of pipe (approximately 12 inches (305 mm) long) attached to a 90o elbow. The
other end of the elbow is attached to a short nipple and fitting suitable for mounting to the motor port
or manifold. The standpipe is installed with the standpipe pointing up in a vertical position. While the
load is being lowered, oil MUST be added to the standpipe as necessary to prevent the motor from
running dry.
4. Fill the standpipe with hydraulic oil, making certain that oil is not running out of the brake valve. If oil is
running out of the brake valve, stop the emergency lowering procedure. Remove the spring retainer
and tap the main spool of the brake valve to the closed position. Replace the spring retainer. After
completing the emergency lowering procedure, the brake valve MUST be serviced and repaired if the
spool was stuck.
WARNING
CAUTION
! !
Do not touch the motor, brake valve or standpipe while lowering a load. They may become hot enough
to cause burns.
6
6. Operate the hand pump up to about 1,000 psi (6,900 kPa). A suspended load will slowly come down.
Releasing the pressure on the hand pump will cause the load to stop. If a chattering noise is heard
while the load is coming down, pump the hand pump to a higher pressure until the noise stops. Do
not exceed 1,500 psi (10,350kPa) to the brake release port.
7. Always inspect the brake plates for signs of overheating and replace if necessary following this proce-
dure. Refer to the applicable Braden or Gearmatic service manual for details.
8. If this procedure was performed due to a malfunction of the hoist, remove the hoist from service and
perform a teardown and inspection to correct the cause of the malfunction before returning the hoist to
service.
PERSONNEL HANDLING
BRADEN recognizes that most hoists and cranes are designed and intended for handling materials and
not personnel. The crane or hoist is only to be used to handle personnel if it can be shown there
is no less hazardous way of carrying out the job. In these situations, all safety precautions must be
strictly adhered to. BRADEN recommends adherence to the latest revision of API 2D (RP 2D) and/or
ANSI/ASME standard B30.5 and/or OSHA and/or other applicable standards for your application. It is
important that you obtain a copy of all applicable safety standards, and that you read and understand
them prior to using the hoist. In addition to, or in conjunction with, the applicable standards, BRADEN
requires *:
• The hoist must be maintained in accordance with the recommendations in this document and the
service procedures in the Installation, Maintenance and Service Manual for your specific hoist.
• When handling personnel, the allowable line pull will be limited to 30% of the hoist rated line pull.
This reduction increases the hoist design factor from 3:1 to 10:1, approximately. Example: a hoist
rated at 15,000 lbs. on the first layer will be rated at 15,000 x 0.3 = 4,500 lbs. on the first layer when
handling personnel.
• Personnel are only permitted to ride in an approved personnel platform as described in API, OSHA or
ANSI/ASME standards.
• The crane must be in good working order and equipped with all required safety equipment, including
an anti two-blocking device or warning signal and a boom angle and length indicator. Two-blocking
occurs when the load block or hook assembly comes in contact with the upper block or point sheave
assembly and often results in damage to the wire rope, rigging and/or hoist.
• Personnel being lifted or supported shall wear safety belts with lanyards attached to designated points
unless lifting over water. If lifting over water, provide approved personal flotation devices (PFD’s).
• The lifting and supporting shall be made under controlled conditions and under the direction of an
appointed signal person.
• The operator and signal person shall conduct a test lift, without personnel in the personnel platform, to
verify adequacy of the crane footing or support. The crane outriggers, if so equipped, must be fully
extended and properly set.
• Cranes shall not travel (move locations) while personnel are on the personnel platform.
• The platform must be landed or tied off, and all brakes set before personnel enters or exits.
7
* If there are any questions, concerns, or conflicts with other safety standards, call or write the BRADEN
Product Support Department, PO Box 547, Broken Arrow, OK, 74012, USA, Telephone (918) 251-8511
Additional information can be obtained from the following organizations:
- Booklet on “Hoisting Personnel”, Crane Institute of America Inc., 1063 Maitland Center Commons,
Suite 100, Maitland, Florida, 32751 USA (800) 832-2726
- OSHA Standard 29 CFR 1926.550 - Cranes, Derricks, Hoists, Elevators, and Conveyors, Occupational
Safety and Health Administration (OSHA), 200 Constitution Ave. N.W., Washington D.C. 20210 USA
(202) 219-4667
- ANSI/ASME Standard B30.5, American National Standards Institute (ANSI), 11 W. 42nd Street, New
York, New York 10036 USA (212) 642-4900
- API Specification RP 2D, American Petroleum Institute (API) 1220 L Street, N.W., Washington, DC
20005 USA (202) 682-8375