KSB Etanorm R

Product Introduction 1211.
1/16-10 G4
50 and 60 Hz
Etanorm/Etanorm-R
Standardized Pumps
Automation products available: PumpExpert PumpDrive (MM) Hyamaster hyatronic
Fields of Application
Water supply Fire-fighting systems Sprinkling Irrigation Drainage Heating Air-conditioning systems Drinking water Service water Hot water Cooling water Swimming pool water Sea water Fire-fighting water Brackish water Condensate Brine Oils Cleaning agents
Designation
EN(-R) 40 - 160 43 (6238) G 10 *) Type series Etanorm Pump size, e.g. Actual impeller diameter - 100 mm, e.g. 143 mm = (angular reduction of impeller vanes) e.g. actual diameter 162/138 mm = Casing material, e.g. JL 1040 2) Shaft seal, e.g. mechanical seal Q1 Q1 X4GG
2) to EN 1561 = GJL-250 *) for Etanorm only
Fluid
Pure liquids not chemically or mechanically aggressive to the pump materials.
Accessories
Drive Surface-cooled KSB-IEC three-phase squirrel cage motor Winding: up to 2.2 kW: 220-240 V/380-420 V 3 kW and above: 380-420 V/660-725 V Design: IMB 3 Enclosure: IP 55 Thermal class: F with temperature sensors: 3 PTC resistors Operating mode: continuous operation S1 or surface-cooled three-phase squirrel cage motor as described above, but West European brand to KSBs choice. Coupling Flexible coupling with/without spacer sleeve Contact Guard Coupling guard as per EN 294. Baseplate Sectional steel / folded steel plate, fabricated sectional steel for the complete unit (pump and motor) in torsion-resistant design.
Operating Data
Q H t p2 up to 1900 m3/h, (528 l/s) up to 102 m -30 C to +140 C up to 16 bar 1)
1) see pressure/temperature limits given on page 5 of type series booklet 1211.5/9-10.
Design
Horizontal volute casing pump, single-stage (pump size 125-200/2 two-stage), with power ratings and main dimensions to EN 733 up to DN 200 / extension Etanorm-R, with bearing bracket, in back pull-out design. Shaft with replaceable shaft sleeve/shaft protecting sleeve in the shaft seal area. Volute casing and impeller with replaceable wear rings. Volute casing with integrally cast pump feet.
Bearings
Deep-groove ball bearings, grease-lubricated.
Shaft Seal
Mechanical seal to EN 12756 (Stanard for Etanorm, for Etanorm-R as option) or gland packing.
Certification
Certified quality management ISO 9001.
Etanorm/Etanorm-R Selection charts

Etanorm
n = 2900 1/min
20 120 100 300 20 30 30 40 50 40 50 US.gpm IM.gpm 100 100 200 200 300 300 400 500 400 500 1000 1000 2000 2000 3000
32-250.1
4)
32-250
2) 3) 4)
40-250
1) 2)
50-250
1) 2)
65-250
1) 2)
80-250
1) 2)
100-250
1) 2)
200
65-200
50
32-200.1
1) 2) 4)
40-200
1) 2)
50-200
1) 2)
1) 2)
40
80-200
1) 2)
32-200
1) 2)
100-200
1) 2)
125-200
1) 2) 4)
30
32-160.1
1) 2) 4)
100
32-160
1) 2)
40-160
1) 2)
50-160
1) 2)
65-160
1) 2)
80-160
1) 2)
100-160
20
32-125 32-125.1
1) 2) 3) 4)
1) 2) 4)
40-125
50-125 65-125
50 40
10 30 ft 20 5 H [m] 4 3.5 4 5 Q[m /h] 2

3
Lieferbar auch in: / Also available in: / Egalement livrable en: / Anche consegnabile in: / Ook leverbaar in: / Tambin disponible en: 1) Zinnbronze / Tin bronze / Bronze ordinaire / Bronzo allo stagno / Tinbrons / Bronce al estao 2) Sphaeroguss / Spheroidal graphite cast iron / Fonte nodulaire / Ghisa sferoidale / Nodulair gietijzer / Fundicin esferoidal Nicht lieferbar in: / Not available in: / Nxiste pas en: / No consegnabile in: / Niet leverbaar in: / No disponible en: 3) Chrom-Nickel-Molybdaen-Stahlguss / Cast chrome nickel molybdenum steel / Acier coul au nickel-chrome-molybdne / Acciaio fuso al cromo-nickel molibdeno / Chroom-nikkel-molybdeen gietstaal / Acero fundido al cromo-niquel molibdeno 4) Ergaenzungsgroessen in EN 733 nicht enthalten / Supplementary sizes not included in EN 733 / Les tailles complmentaires ne sont pas couvertes par EN 733 / Grandezze suppplementari non incluse in EN 733 / Aanuullende grootten niet in EN 733 inbegrepen / Tamaos adicionales no includdos en EN 733
10 3 4 5
20 l/s
30 10
40
50 20
100 30 40 50
200
300 100
400
500
700
KE1211.452/8
Etanorm / Etanorm-R
n = 1450 1/min
10 100 US.gpm 10 20 20 30 30 40 50 40 50 100 100 200 200 300 400 300 500 400 500 1000 1000 2000 2000 3000 4000 5000 3000 4000 5000 300 125--500.2R 2) 4) 150--500.1R
2) 4)
IM.gpm
200--500R
2) 4)
50 80--400 4) 40 30 40--315 2) 4) 50--315 2) 4) 20 32--250.1

4)
300--500R 2) 4) 250--500R
2) 4)
200
100--400
125--400
2)
150--400
1) 2)
200--400R
2) 4) 2) 4)
300--400R
2) 4)
65--315 2)
80--315 2)
100--315
1) 2)
125--315
1) 2)
250--400R
100
150--315
1) 2)
32--250
2) 4)
40--250
1) 2)
50--250 1) 2)
65--250
1) 2)
80--250
1) 2)
200--330R 100--250
1) 2)
250--330R
2) 4)
125--250
1) 2)
2) 4)
300--360R
2) 4)
50 40
150--250
1) 4)
32--200.1 1) 2) 4) 10 32--160.1
1) 2) 4)
32--200
1) 2)
40--200 1) 2)
50--200
65--200
1) 2) 1) 2)
80--200 1) 2) 100--200
1) 2)
125--200 150--200
200--260R
2) 4)
300--340R
2) 4)
30
32--160
1) 2)
40--160 1) 2)
50--160 1) 2)
4)
250--300R 200--250R
2) 4) 2) 4)
65--160
1) 2)
80--160
1) 2)
100--160
1) 2) 4)
20
5 4 3 32--125.1 1) 2) 3) 4)
32--125
40--125
50--125 65--125 10
2 H [m]
5 4 ft 3 2000 400 500 KE1211.454/9
1 0.8
3
3 1
Q[m /h] 2
10 3 4 5
20 l/s
30 10
40
50 20
100 30 40
200 50
300
400 100
500 200
1000 300
Etanorm/Etanorm-R
Etanorm
n = 3500 1/min
30 100 30 40 50 40 50 US.gpm IM.gpm 100 100 200 200 300 300 400 500 400 500 1000 1000 2000 2000 300 3000
32-200.1 1) 2) 4) 32-200 1) 2)
40-200 1) 2)
50-200 1) 2) 65-200 1) 2)
80-200 1) 2)
200
100-200 1) 2) 125-200
50
32-160.1 1) 2) 4)
1) 2) 4) 40-160 32-160 1) 2) 1) 2) 50-160 1) 2)
40
65-160 1) 2) 80-160 100-160 1) 2) 1) 2) 4)
30
32-125 32-125.1 1) 2) 3) 4) 40-125 50-125
100
20
65-125
H [m]
50
40
10
30
ft
6 6 2 10 3
20 500 800 200 KE1211.4062/6
Q[m /h] 4 5
20 l/s
30 10
40
50 20
100 30 40 50
200
300 100
400
Etanorm / Etabloc / Etanorm-R

n = 1750 1/min
10 100 US.gpm 10 20 20 30 30 40 50 40 50 100 100 200 200 300 400 300 500 400 500 1000 1000 2000 2000 3000 4000 5000 3000 4000 5000
10000 10000 300
IM.gpm
80--400 4) 50 40--315 40 30 32--250.1 4) 20 32--200.1 1) 2) 4) 32--200 1) 2) 32--160.1 1) 2) 4) 10 32--160

1) 2) 4)
125--400 2) 100--400 200--400R 2) 4) 150--400

1) 2)
300--400R
2) 4)
200
50--315 4)
65--315 2)
80--315
2)
100--315
1) 2)
125--315
1) 2)
250--400R
2) 4)
150--315
1) 2)
250--330R 200--330R
2) 4) 2) 4)
300--360R
2) 4)
100
32--250
2) 4)
40--250
1) 2)
50--250
1) 2)
65--250
1) 2)
80--250
1) 2)
100--250
1) 2)
125--250
1) 2)
150--250 40--200
1) 2)
50--200
1) 2)
65--200
1) 2)
80--200
1) 2)
125--200 100--200
1) 2) 1) 2) 4)
1) 4)
200--260R
2) 4)
300--340R
2) 4)
50 40
150--200 40--160
1) 2)
50--160
1) 2)
4)
65--160
1) 2)
250--300R 200--250R
2) 4) 2) 4)
80--160
1) 2)
30
100--160
1) 2) 4)
32--125.1 1) 2) 3) 4)
32--125 40--125 50--125 65--125
20
5 4 3
10
2 H [m]
1 2 3 1 4 5 l/s
5 ft 4
Q[m /h] 2
10 3 4 5
20
30 10
40
50 20
100 30 40
200 50
300
400 100
500 200
1000 300 400
2000
3000
500 KE1211.4064/10
Etanorm/Etanorm-R Materials
Etanorm G / Etanorm-RG Volute casing Discharge cover Impeller Spaltringe Shaft Shaft sleeve Shaft protection sleeve Bearing bracket Etanorm-R GC1 Etanorm M Etanorm-RM Etanorm B Tin bronze CC 480 K--GS 3) Tin bronze CC 480 K-GS 3) Tin bronze CC 480 K-GS 3) Leaded bronze CC 495 K-GS 3) Chrome nickel molybdenum steel 1.4462 Chrome nickel molybdenum steel 1.4571 Chrome nickel molybdenum steel 1.4571 Grey cast iron JL 1040 1) Etanorm C Cast chrome nickel molybdenum steel 1.4408 Cast chrome nickel molybdenum steel 1.4408 Cast chrome nickel molybdenum steel 1.4408 Cast chrome nickel molybdenum steel 1.4408 Chrome nickel molybdenum steel 1.4462 Chrome nickel molybdenum steel 1.4571 Chrome nickel molybdenum steel 1.4571 Grey cast iron JL 1040 1) Grey cast iron JL 1040 1) Grey cast iron JL 1040 1) Grey cast iron JL 10401) 1.4408 Grey cast iron GG Tempering steel C45 Chrome nickel molybdenum steel 1.4571 1.4122 Grey cast iron JL 1040 1) Grey cast iron JL 1040 1) Tin bronze CC 480 K--GS 3) Grey cast iron/Leaded bronze CC 495 K-GS 3) Tempering steel C45 Chrome nickel molybdenum steel 1.4571 1.4122
Chrome nickel molybdenum steel 1.4122 Grey cast iron JL 1040

1)
Chrome nickel molybdenum steel 1.4122 Grey cast iron JL 1040 1) Etanorm-RS
Etanorm S Volute casing Discharge cover Impeller Spaltringe Shaft Shaft sleeve Shaft protection sleeve Bearing bracket
1) to EN 1561 = GJL-250 2) to EN 1563 = GJS-400-18-LT 3) to EN 1982
Sphroguss JS 1025 2) Sphroguss JS 1025 2) Grey cast iron JL 1040 1) Grey cast iron GG Tepering steel C45 Chrome nickel molybdenum steel 1.4571 1.4122 Chrome nickel molybdenum steel 1.4122 Grey cast iron JL 1040 1)
Benefits at a Glance
Large material selection Grey cast iron, tin bronze, nodular cast iron, cast chrome nickel molybdenum steel Pressure jacket designed for 16 bar to guarantee high operating reliability
Connecting dimensions and power ratings to EN 733 (Etanorm)
UGI055219
Wear rings service-friendly
S
Robust deep-groove ball bearings, protected against contamination by v-rings (Etanorm) Shaft sleeve/shaft protecting sleeve prevents wear on the shaft
1211.1/16-10
Impeller with optimized hydraulics, excellent efficiencies and fine graduation of the QHperformance chart
Mechanical seal or gland packing, uncooled
Back pull-out design: easy dismantling, the casing may remain in the pipeline when the pump is dismantled
KSB Aktiengesellschaft P.O. Box 1361, 91253 Pegnitz Bahnhofplatz 1, 91257 Pegnitz (Germany) Tel. +49 9241 71-0 Fax +49 9241 71-1791 www.ksb.com
15.04.2007
Suction geometry designed for max. suction capacity (NPSH) and optimal cavitation behaviour
Subject to technical modification without prior notice.
Type: Etanorm-R

KSB Etanorm R

Uploaded by

Copyright:

Available Formats

KSB Etanorm R

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

KSB Etanorm R

Uploaded by

Copyright:

Available Formats

Product Introduction 1211.

Automation products available: PumpExpert PumpDrive (MM) Hyamaster hyatronic

1) see pressure/temperature limits given on page 5 of type series booklet 1211.5/9-10.

Etanorm/Etanorm-R Selection charts

10 30 ft 20 5 H [m] 4 3.5 4 5 Q[m /h] 2

50 80--400 4) 40 30 40--315 2) 4) 50--315 2) 4) 20 32--250.1

5 4 ft 3 2000 400 500 KE1211.454/9

1) 2) 4) 40-160 32-160 1) 2) 1) 2) 50-160 1) 2)

65-160 1) 2) 80-160 100-160 1) 2) 1) 2) 4)

20 500 800 200 KE1211.4062/6

Etanorm / Etabloc / Etanorm-R

10000 10000 300

80--400 4) 50 40--315 40 30 32--250.1 4) 20 32--200.1 1) 2) 4) 32--200 1) 2) 32--160.1 1) 2) 4) 10 32--160

125--400 2) 100--400 200--400R 2) 4) 150--400

32--125 40--125 50--125 65--125

1000 300 400

Chrome nickel molybdenum steel 1.4122 Grey cast iron JL 1040

Connecting dimensions and power ratings to EN 733 (Etanorm)

Wear rings service-friendly

Mechanical seal or gland packing, uncooled

Subject to technical modification without prior notice.

You might also like