Acer X193W Service Guide

Service guide files and updates are available on the CSD web: for more information, Please refer to http://csd.acer.com.tw/

100% Recycled Paper

Copyright
Copyright 2003 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.

Disclaimer
The information in this guide is subject to change without notice. Acer Incorporated makes no representations or warranties, either expresses or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose, Any Acer Incorporated software described in this manual is sold or licensed as is . Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, of its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.

Acer is a registered trademark of Acer Corporation. Intel is a registered trademark of Intel Corporation. Pentium and Pentium II/III are trademarks of Intel Corporation. Other brand and product names are trademarks and/or registered trademarks of their respective holders.

Conventions
The following conventions are used in this manual:

Screen messages

Denotes actual messages that appear on screen

Note

Gives bits and pieces of additional information related to the current topic.

Warning

Alerts you to any damage that might result from doing or not doing specific actions.

Caution

Gives precautionary measures to avoid possible hardware or software problems.

Important

Reminds you to do specific actions relevant to the accomplishment of procedures.

Preface
Before using this information and the product it supports, please read the following general information. 1. this Service Guide provides you with all technical information relating to the BASICCONFIGURATION decided for Acers global product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please contact your regional offices or the responsible personnel/channel to provide you with further technical details. 2. please not WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the printed Service Guide, for ACER -AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and Service of customer machines.

WARNING: (FOR FCC CERTIFIED MODELS)

NOTE: this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, Which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help.

NOTICE:
1. The changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibility of the user to correct such interference. As an ENERGY STAR Partner our company has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

WARNING:
To prevent fire or chock hazard, do not expose the monitor to rain or moisture. Dangerously high voltages are present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.

PRECAUTIONS
l Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, Swimming pool or in a wet basement. Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a trolley o r stand recommended by the manufacture or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacture and follow the kit instructions. l Slots and openings in the back and bottom of the cabinet area provided for ventilation. To ensure reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug or similar surface. Do not place the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided. l The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. l The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug. l Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges. l l Do not overload power strips and extension cords. Overloading can result in fire or electric shock. Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric shock. Never spill liquids on the monitor. l Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel. l To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100-240V AC, Min. 3.5A. l l The wall socket shall be installed near the equipment and shall be easily accessible. For use only with the attached power adapter (output 12V DC) which have UL,CSA listed license

SPECIAL NOTES ON LCD MONITORS

The following symptoms are normal with LCD monitor and do not indicate a problem.

NOTES
l Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. l l You may find slightly uneven brightness in the screen depending on the desktop pattern you use. The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the time. l Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for hours.

Table of contents
Chapter 1 MONITOR FEATURE 9 Chapter 2 OPERATING INSTRUTION 17 Chapter 3 M ACHINE ASSEMBLY ..24 Chapter 4 TROBLE SHOOTING ..29 Chapter 5 CONNECTOR INFORMATION ..32 Chapter 6 FRU LIST .33 Chapter 7 SCHEMATIC DIAGRAM 35

Chapter 1
Monitor Feature
Driving system Size Pixel pitch Viewable angle TFT Color LCD 19"W 0.2835 mm 160(H) x 160 (V) degree MTD panel: 300 cd/m (typ.) Brightness AUO panel: 300 cd/m (typ.) MTD panel: 600:1(typ.) Contrast Ratio LCD Panel Response time Video Input Separate Sync H-Frequency V-Frequency AUO panel: 600:1(typ.) 5ms (Tr+Tf) R,G,B Analog, DVI box (optional) H/V TTL 31-80KHZ 56-75HZ MTD: 16. 5 million Colors Display Color Maximum Dot Clock Max Resolution Plug & Play ON Mode EPA ENERGY STAR Audio output Input Connector Input Video Signal OFF Mode AUO: 16.7 million Colors 140MHz 1440X900 @75HZ VESA FPMPMI <37W <1W Rated Power 2.0W rms(Per channel) D-Sub 15 pin, DVI- D connector(optional) Analog : 0.7Vp-p,75OHM Horizontal : 408.24mm Screen Size (Active) Power Source Environmental Considerations Vertical : 255.15mm 90~264 Vac, 47~63HZ Operating Temp : Storage Temp : Operating Humidity : Weight (N.W.) Dimension TBDkg 506(W) x 415(H) x 126(D) mm(with packing) 5 to 40 degree ; -20 to 60 degree ; 20% to 80%

* Power Switch * MENU / EXIT * * Switch / Volume / Volume

* AUTO / ENTER * e-Color * Contrast/brightness * Focus * Clock * H.Position * W.Position * Language * OSD Color temperature * OSD Position & Timeout * Auto Config * Input * Information * Reset External Controls : Regulatory Compliance * Exit cUL, FCC, TUV, CE, TCO03.

Timings
The product has 34 memory modes in total. 26 modes are preset and 8 modes are user definable.

MODE NO. RESOLUTION Dot clock(MHz) fh H-Total ( us ) H-Sync ( us ) H-B-P ( us ) H-Active ( us ) H-F-P ( us ) f v V-Total (ms ) V-Sync ( ms ) V-B-P (ms ) V-Active ( ms ) V-F-P ( ms ) SYNC. H/V POLARITY SEP . SYNC MODE NO. RESOLUTION Dot clock(MHz) fh H-Total ( us ) H-Sync ( us ) H-B-P ( us ) H-Active ( us ) H-F-P ( us ) f v V-Total (ms ) V-Sync ( ms ) V-B-P (ms ) V-Active ( ms ) V-F-P ( ms ) SYNC. H/V POLARITY SEP . SYNC Y 640 x 480 31.5 Y 720 x 400 28.321

1 640 x 480 25.175

2 640x480 30.24 35.0kHz

3 640 x 480 31.5

31.469kHz 31.78(900dots) 3.813(108dots) 1.907(54dots) 25.42(720dots) 0.636(18dots) 70Hz(70.087) 14.27(449 lines) 0.064(2 lines) 1.112(35 lines) 12.71(400 lines) 0.384(12 lines) -/+

31.469kHz 31.778 (800 dots) 3.813 (96 dots) 1.907 (48 dots) 25.422 (640 dots) 0.636 (16 dots) 60Hz (59.940) 16.683 (525 lines ) 0.064 (2 lines ) 1.049 (33 lines ) 15.253 (480 lines ) 0.317 ( 10 lines) -/-

37.861kHz 26.413 (832 dots) 1.270(40 dots) 4.064(128 dots) 20.317(640 dots) 0.762(24 dots) 72.809Hz 13.735(520 lines) 0.079(3 lines) 0.739(28 lines) 12.678(480 lines) 0.237(9 lines) -/-

28.571(864 dots) 2.116 (64 dots) 3.175 (96 dots) 21.164 (640 dots) 2.116 (64 dots) 66.7 HZ (66.667) 15.000 (525 lines ) 0.086 (3 lines ) 1.114 (39 lines ) 13.714 (480 lines ) 0.086 (3 lines ) +/+ Or -/-

Y 5 800 x 600 36 35.16kHz 28.44(1024 dots) 2.00(72 dots) 3.56(128 dots) 22.22(800 dots) 0.67(24 dots) 56.25 17.78(625 lines) 0.06(2 lines) 0.63(22 lines) 17.07(600 lines) 0.03( 1 line) +/+ 6

Y 7 800 x 600 40 37.879kHz 26.40 (1056 dots) 3.200 (128 dots) 2.200 ( 88 dots) 20.00 ( 800 dots) 1.000 (40 dots) 60Hz (60.316) 16.58 (628 lines) 0.106 (4 lines) 0.607 (23 lines) 15.84 (600 lines) 0.026 (1 line ) +/+

Y 8 800 x 600 49.5 46.875kHz 21.333 (1056dots) 1.616 (80 dots) 3.232 (160 dots) 16.162 (800 dots) 0.323 (16 dots) 75Hz (75.000) 13.333 (625lines) 0.064 (3 lines) 0.448 (21 lines) 12.80 (600lines) 0.021 (1 line ) +/+

37.500kHz 26.667(840 dots) 2.032 (64 dots) 3.810 (120 dots) 20.317 (640 dots) 0.508 (16 dots) 75Hz (75) 13.333 (500 lines) 0.080 (3 lines) 0.427 (16 lines) 12.80 (480 lines) 0.027 ( 1 line ) -/-

MODE NO. RESOLUTION Dot clock(MHz) fh H-Total ( us ) H-Sync ( us ) H-B-P ( us ) H-Active ( us ) H-F-P ( us ) f v V-Total (ms ) V-Sync ( ms ) V-B-P (ms ) V-Active ( ms ) V-F-P ( ms ) SYNC. H/V POLARITY SEP . SYNC MODE NO. RESOLUTION Dot clock(MHz) fh H-Total ( us ) H-Sync ( us ) H-B-P ( us ) H-Active ( us ) H-F-P ( us ) f v V-Total (ms ) V-Sync ( ms ) V-B-P (ms ) V-Active ( ms ) V-F-P ( ms ) SYNC. H/V POLARITY SEP . SYNC Y Y2 800 x 600 50

10 832 x 624 57.283 49.72kHz 20.11(1152 dots) 1.12(64 dots) 3.91(224 dots) 14.52( 832 dots ) 0.56(32 dots ) 74.55Hz 13.41(667 lines) 0.06(3 lines) 0.78(39 lines) 12.55 (624 lines) 0.02(1 line) +/+

11 1024 x 768 65 48.363kHz 20.677(1344 dots) 2.092(136 dots) 2.462(160 dots) 15.754(1024 dots) 0.369(24 dots) 60.004Hz 16.666(806 lines) 0.124(6 lines) 0.600(29 lines) 15.880(768 lines) 0.062(3 lines) -/-

12 1024 x 768 75 56.48kHz 17.71(1328 dots) 1.81(136 dots) 1.92(144 dots) 13.65(1024 dots) 0.32(24 dots) 70.07Hz 14.27(806 lines) 0.11(6 lines) 0.51(29 lines) 13.60(768 lines) 0.05(3 lines) -/-

48.077kHz 20.80 (1040dots) 2.400 ( 120 dots) 1.280 (64 dots) 16.00 (800 dots) 1.120 (56 dots) 72Hz (72.188) 13.85 (666 lines) 0.125 (6 lines) 0.478 (23 lines) 12.48 (600 lines) 0.770 ( 37 +/+ line )

Y 13 14 1280 x 1024 108 63.981kHz 15.630 (1688 dots) 1.037 (112 dots) 2.296 (248 dots) 11.852 (1280 dots) 0.444 (48 dots) 60.020Hz 16.661 (1066 lines) 0.047 ( 3 lines) 0.594 ( 38 lines) 16.005 (1024 lines) 0.016 (1 line ) +/+

Y 15 1280 x 1024 135 79.976KHz 12.504 (1688 dots) 1.067 (144 dots) 1.837 (248 dots) 9.481 (1280dots) 0.119 (16 dots) 75.025 Hz 13.329 (1066 lines) 0.038 (3 lines) 0.475 (38 lines) 12.804(1024 lines) 0.013 (1 lines) +/+

Y 16 1152 x 864 108 67.5 KHz 14.815(1600 dots) 1.185(128 dots) 2.370(256 dots) 10.667(1152 dots) 0.593(64 dots) 75.06 Hz 13.333(900 lines) 0.044(3 lines) 0.474(32 lines) 12.800(864 lines) 0.015(1 lines) +/+

1024 x 768 78.75 60.02kHz 16.66(1312 dots) 1.22 (96 dots) 2.23 (176 dots) 13.00 (1024 dots) 0.20 (16 dots) 75.03Hz 13.33 (800 lines) 0.05 (3 lines) 0.47 (28 lines) 12.80 (768 lines) 0.02 (1 lines) +/+

MODE NO. RESOLUTION Dot clock(MHz) fh H-Total ( us ) H-Sync ( us ) H-B-P ( us ) H-Active ( us ) H-F-P ( us ) f v V-Total (ms ) V-Sync ( ms ) V-B-P (ms ) V-Active ( ms ) V-F-P ( ms ) SYNC. H/V POLARITY SEP . SYNC MODE NO. RESOLUTION Dot clock(MHz) fh H-Total ( us ) H-Sync ( us ) H-B-P ( us ) H-Active ( us ) H-F-P ( us ) f v V-Total (ms ) V-Sync ( ms ) V-B-P (ms ) V-Active ( ms ) V-F-P ( ms ) SYNC. H/V POLARITY SEP . SYNC Y Y

17 1280 x 960 108 60.000 KHz 16.667 (1800dots) 1.037 ( 112 dots) 2.889 (312 dots) 11.852 (1280 dots) 0.889 (96 dots) 60.00Hz 16.667 (1000 lines) 0.050 (3 lines) 0.600 (36 lines) 16.000 (960 lines) 0.017 ( 1 +/+ line )

19 1280 x 720 74.481 44.760KHz 22.341 (1664dots) 1.826 ( 136 dots) 2.578 (192 dots) 17.186 (1280 dots) 0.752 (56 dots) 60.000Hz 16.667 (746 lines) 0.067 (3 lines) 0.492 (22 lines) 16.086 (720 lines) 0.022 (5 lines) -/+

20 1280 x 768 79.5 47.776KHz 20.931 (1664dots) 1.61 ( 128 dots) 2.415 (192 dots) 16.101 (1280 dots) 0.805 (64 dots) 59.87Hz 16.703 (798 lines) 0.147 (7 lines) 0.419 (20 lines) 16.075 (768 lines) 0.063 (3 lines) -/+

21 1280 x 768 102.25 60.289KHz 16.587 (1696dots) 1.252 ( 128 dots) 2.034 (208 dots) 12.518 (1280 dots) 0.782 (80 dots) 74.893Hz 13.352 (805 lines) 0.116 (7 lines) 0.448 (27 lines) 12.739 (768 lines) 0.05 (3 lines) -/+

Y 22 23 1440 x 900 106.5 55.935KHz 17.878 (1904dots) 1.427 ( 152 dots) 2.178 (232 dots) 13.521 (1440 dots) 0.751 (80 dots) 59.887Hz 16.698 (934 lines) 0.107 (6 lines) 0.447 (25 lines) 16.09 (900 lines) 0.054 (3 lines) -/+

Y 24 1440 x 900 136.75 70.635KHz 14.157 (1936dots) 1.112 ( 152 dots) 1.814 (248 dots) 10.53 (1440 dots) 0.702 (96 dots) 74.984Hz 13.336 (942 lines) 0.085 (6 lines) 0.467 (33 lines) 12.741 (900 lines) 0.042 (3 lines) -/+

Y 26 848 x 480 33.75 31.02 KHz 32.237 (1088 dots) 3.319 (112 dots) 3.319 (112 dots) 25.126 (848 dots) 0.474 (16 dots) 60 Hz 16.667 (517 lines ) 0.258 (8 lines ) 0.741 (23 lines ) 15.474 (480 lines ) 0.193 (6 lines ) +/+

1360 x 768 85.5 47.712KHz 20.959 (1792dots) 1.31 ( 112 dots) 2.994 (256 dots) 15.906 (1360 dots) 0.749 (64 dots) 60.015Hz 16.662 (795 lines) 0.126 (6 lines) 0.377 (18 lines) 16.097 (768 lines) 0.063 (3 lines) +/+

BLOCK DIAGRAM
DVI_INPUT DVI-D DVI_IIC TO PANEL

EEPROM EDID 24C02 SCALER RTD2525LH(RTD2545L)

PANEL CONNETER

D_SUB15_INPUT(R/G/B/HS/VS/SOG)

D-SUB15

D-SUB15_IIC

EEPROM EDID 24C02

CONTROL BUS

EEPROM 24C16 MCU RTD2021

BUTTON BOARD
B B

5DVCC

AUDIO INPUT 33VCC LDO TO 3.3V POWER BOARD

AUDIO AMP TPA6021A4 SPEAKER

18DVCC LDO TO 1.8V

PCB CONDUCTOR VIEW

e2

Chapter 2
OPERATING INSTRUCTIONS
Front Panel Definition This Section defines the front panel User Interface for Led Indictor and Key function. Key Definition: There are six keys defined in this system and described bellows. * Adjusting display settings(User can select the key "AUTO + < + POWER" to enter factory mode)

External Controls Power on/off 1 POWER Blue: power on Amber: in sleep mode OSD Function Press to view OSD. Press again to exit a selection in OSD. If OSD is active, press to select or adjust OSD options. If OSD is inactive, press once, then press the buttons marked or to adjust the volume.

Left/ PLUS

Right / MINUS

If OSD is active, press to select or adjust OSD options. If OSD is inactive, press once, then press the buttons marked or to adjust the volume.

If OSD is active, press to enter a selection in OSD. If OSD is 5 AUTO inactive, press and the monitor will automatically optimize the position, focus and clock of your display.

Adjusted Brightness and Contrast by e-color, there are 5 eColor options for your refrence: User, Text, Standard, Graphics, Movie

OSD options OSD options OSD options

OSD menu

Acer eColor Management: Brightness and Contrast adjusted by Acer eColor Management. User: Brightness and Contrast adjusted by User mode.

Focus: This removes any horizontal distortion and makes the picture clear and sharp. Clock: If there are any vertical stripes seen on the background of the screen, this renders them less noticeable by minimizing their size. It also changes the size of the horizontal screen.

H-Position: This adjusts the horizontal. V-Position: This adjusts the vertical.

Color adjustment: There are three ways to adjust color: Warm (reddish white) Cool (bluish white) User (you can adjust the colors red, green and blue to the intensity you desire)

OSD options OSD options

Language for EU: English, Deutsch, Espanol, Hollands, Pyccknn, Francais, Italiano, Suomalainen

OSD Settings: This changes the position of the OSD window on the screen and the staying time.

Input signal: Select either Analog Input or Digital Input video.

Information: This shows information about the screen.

This page only be visible in factory mode R,G,B OFFSET : Adjust current RGB cut off level R,G,B GAIN : Adjust current RGB Driver value. SPREAD : Adjust chip set internal frequency spread effect for EMI testing.

This page only be visible in factory mode

AUTO BURN : Use the chip set internal pattern for hot running monitor panel and inverter. AUTO COLOR : Perform Auto Balance measurement by chip set internal signal. And reference these values to initial all other color temperature detail parameters. COLOR UPDATE: Force presently R,G,B offset and gain parameters update to currently temperature memory address. FACTORY RESET : Recall to factory setting and power off immediately. VERSION : Display F/W version and panel vender and DDC serial no.

Acer e-color management

User Text Standard Graphics Movie

Brightness 77 44 77 97 77

Contrast 50 50 50 60 56

LED Definition
The system equips one dual color (blue/amber) led to indict system status and defined as bellows:

LED Color Blue Amber Dark

System Status System in normal operation mode System in power-saving mode System in power-off mode

LOGO:
When the monitor is power on, the LOGO will be showed in the center, and disappear slowly.

HOW TO OPTIMIZE THE DOS-MODE

Plug and play Plug & play DDC2B feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC2B. The DDC2B is a bi-directional data channel based on the I2 C protocol. The host can request EDID information over the DDC2B channel.

THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL. This monitor meets the Green monitor standards as set by the Video Electronics Standards Association(VESA) and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees (NUTEK). This feature is designed to conserve electrical energy by reducing power consumption when there is no video-input signal present. When there is no video input signal this monitor, following a time -out period, will automatically switch to an OFF mode. This reduces the monitors internal power supply consumption. After the video input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to a Screen Saver feature except the display is completely off. The display is restored by pressing a key on the keyboard, or clicking the mouse.

USING THE RIGHT POWER CORD The accessory power cord for the Northern American region is the wallet plug with NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for the power cord shall be 125 volt AC. Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of a minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type attachment plug, rated 10A, 250V,CEE-22 male configuration. The other end terminates with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. Please note that power supply card needs to use VDE 0602, 0625, 0821 approval power cord in European counties.

Chapter 3
Machine assembly
This chapter contains step-by-step procedures on how to assemble the monitor for maintenance and trouble shooting NOTE: 1. The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding to avoid mismatch when putting back the components. 2. Note: The monitor surface is susceptible to scratching! Therefore, lay the monitor on a soft surface when mounting or removing the base. 3. Wear gloves. Front View: (unit: mm)

Real View:

Side View:

(unit: mm)

Assembly Procedure

1. Take out hinge cover from stand.

2. Remove 4pcs screws from stand and take out it.

3. Remove 1pcs screw from rear cover and take out it.

4. Tear off all the tapes.

5. Tear off the lamp cable from p/b.

6. Remove 2pcs screws from PCB shielding.

7. Tear off the b/b cable from m/b.

8. Take off the PCB shielding and bezel from panel.

9. separate the b/b from bezel.

10. Remove 4pcs IO NUTs from m/b.

11. Remove 8pcs screws from m/b and p/b, then separate them..

Chapter 4
TROUBLE SHOOTING
This chapter provides trouble shooting information for X193W

1. No Power No Power

Change Power Board

NO

Check CN1 +5V

No Check Short Of Main Board

Yes

Check Q7,Q8,=1.8V

NO Change Q7,Q8,Q9,U1 Yes

Change Y1

NO

Check Y1=24MHz

Yes

Change U3 or U7 Change U5 RUN Software ISP

NO Check U3 Pin 15,16 Clock

Yes

Check U7 Check Bottom Board Pin X1 Clock

NO Change U7

2. Missing Color Missing Color

Change Cable

NO

Check VGA Cable

Yes

Check R70,R73,R78 Change R70,R73,R78 Yes NO

Change U7 or CN8 Cable or Panel

NO

Check CN8 LVDS Signal

Yes

Adjustment R/G/B Color

NO Check OSD R/G/B Gain

Yes

Change Panel

3. Always show NO SIGNEL NO SIGNEL

Change Cable

NO

Check VGA Cable

Yes

Yes VGA Check C20,C23,R70,R7 3 Change U7

NO Change R70,R73,L5,R73 ,R75 C22,C24

Chapter 5
Connector Information
Phone jack stereo PIN1. AC power cord: CEE22 typed connector PIN2. Audio cable PIN3. Audio: Line-in receptacle

Video signal connector 15P Mini D-Sub connector x 1

PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Signal Red Green Blue No Pin Ground Ground Red Ground Green Ground Blue +5 V for DDC Ground Ground SDA (DDC Data) H Sync V Sync SCL (DDC Clock)

Chapter 6
FRU (Field Replaceable Unit) LIST
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of X193W. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). NOTE: Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel(http://aicsl.acer.com.tw/spl/). For whatever reasons a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED CERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts repair and service of customer machines. NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how best to dispose it, or follow the rules set by your regional Acer office on how to return it.

Chapter 7
D D

SCHEMATIC DIAGRAM

CONTENTS SCHEMATIC
CONTENT POWER MCU VGA AND TMDS INPUT RTD2525LH

SHEET
35 36 37 38 39 40
B

AUDIO

5DVCC 5DV L19 EC1 100uF/16V C1 0.1u/6 120/CX20129813/8 CN1 CONN 3x2-R 3DVCC 3DVCC R3 0 ohm/6 L1 120/CX20129813/8 U1 AIC1084/TO252 3 VIN VOUT 2 VO 4 GND
D

AUDIO POWER

C1,EC1,L19 CLOSED CN1

1 3 5

2 4 6

R2 1K4/6 1%

EC3 100uF/16V +

R6 Q1 MMBT3906 L2 2 1U/6

1K/6

VRMT R5 2.2K/6 1%

1 10K/6

C3

C68 0.1U/6

U1-1 3 VIN

VOUT GND

3DVCC AIC1117/NC
C

U1U1-1layout
C

R8 1K/6 R9 C4 1U/8/NC 2 Q2 DTC144EUA 1 VBRI U2-1 AP1117/NC 3 VIN VOUT 2 GND 0/6 3

2005/09/30

C2

0.1u/6

TO252 package

2005/09/30

U2U2-1layout
MCU_VCC D7 A
B

1.8DVCC U2 AP1084/NC 3 VIN VOUT 2 VOUT 4 GND R10 330/6 1%/NC C5 0.1u/6/NC + EC4 100uF/16V/NC

D6 K A K SMB/NC

D1 DSUB_5V 1N4148 D4 Bus_Power 1N4148

D2 2 1N4148 1

D35 120/CX201209813/8 3 L3 EC2 100uF/16V BAT54C 0.1u/6

SMB/NC

C9

3DVCC 1

D3 SSM12 2

FOR PC99
3 D
SN7002E

M1 M2 M3 S10M30 S10M30 S10M30

G
A

2 3 C

MH1 M34-D80 5 4 3

MH2 M34-D80
A

MMBT3906

2 1 7 8 9

5 4 3

2 1 7 8 9

2 E

R1 150/6 1%/NC

2007.11.22 pin define modify

MCU_VCC MCU_VCC

3DVCC

CN3 10 9 8 7 6 5 4 3 2 1 10 9 8 7 6 5 4 3 2 1 MENU_O SEL_O PWR_O UP_O DOWN_O RIGHT_O LEFT_O R1 G1

*Co-lay CN3/CN2 note: R24 CN3 NC R25 NC

Reset circuit
U5 VCC
4

R12 C6 10K/6 LED_G

R13 10K/6 2

3 2 1

R7 RST 1K/6/NC

3 C
R14 4.7K/6 2 1 Q5 3 Q4 MMBT3906 MMBT3906

CN2

RST GND

1U/6/NC R16 82K/6/NC

1K

1K
4

7101-E10N

NC/TCM810S

LED_R

R17

4.7K/6

MMBT3906 3

MCU_VCC

HOTKEY_M KEY1 KEY2 PWR KEY1 KEY2 KEY1 KEY2 R19 R20 R21 R22 R23 R24 R25 R26 R27 C11 0.1u/6 C12 0.1u/6 C13 0.1u/6 C7 0.1u/6 C8 0.1u/6 1K/6 1K/6 1K/6 4.7K/6 4.7K/6 10K/6 10K/6 200/6 300/6 2005/09/30 MENU_O SEL_O PWR_O UP_O DOWN_O RIGHT_O LEFT_O R1 G1

CN2 10 9 8 7 6 5 4 3 2 1

5DVCC

R166 4.7K/6

R52 4.7K/6

R53 4.7K/6

U4 8 7 6 5 VCC WP SCL SDA A0 A1 A2 GND 1 2 3 4

C16 0.1u/6

D37 NC/DAN217K HOTKEY_M 3

D29 DAN217K

D30 DAN217K

D31 DAN217K

KEY1

KEY2

PWR

EEPROM_WP IICSCL IICSDA

Junction from A change to B

4501-10-10P-R

AT24C16N-10SC-2.7

TO BUTTON BOARD
3

MCU_VCC R32 4.7K/6 R33 4.7K/6 R35 4.7K/6 R36 4.7K/6

MCU_VCC R37 RST R38 4.7K/6 4.7K/6 R44 4.7K/6/NC 4.7K/6 4.7K/6 4.7K/6 4.7K/6 4.7K/6 4.7K/6 100/6 100/6

PANEL_PW12 RTD_SD3/SDI RTD_SCLK VRMT

MCU_VCC R48 R170 R171 R39 R45 R46 R47 41 40 39 38 37 36 35 34 33 4 5DVCC R191 NC/4.7K/6 4.7K/6 4.7K/6 4.7K/6 4.7K/6

R41

DSUB_DET DVI_DET Hot_Plug VBRI VOLUME DDC2_SCL DDC2_SDA STBY

R164 R168 R167 R54 R56

100/6 100/6 100/6 100/6 100/6

44 45 46 47 48 1 2 3 9 10 11 12 13 14 8 5

VCC

RST

P5.0/PWM0 P5.1/PWM1 P5.2/PWM2 P5.3/PWM3 P5.4/PWM4 P5.5/PWM5 DSCL2/P5.6 DSDA2/P5.7

P1.0/T2 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7

EEPROM_WP IICSCL R59 IICSDA R161 LED_G LED_R R162 R163 100/6 100/6

100/6 100/6

U3 RTD2120L Y1

15

16

24MHz R165 NC/1M/6 C14 10pF/6

1

C15 10pF/6
1

17 18 19 6 7

VSS NC NC NC NC

XO

XI

DDC_SDA DDC_SCL

NC NC NC NC VSYNC NC NC RTD2120L P3.2/INT0 P6.7 P3.3/INT1 P6.6/CLKO1 P3.4/T0 P6.5 P3.5/T1 P6.4 P7.6/CLKO2 P6.3/ADC3 P7.7 P6.2/ADC2 P6.1/ADC1 ASDA/P3.1/TXD P6.0/ADC0 ASCL/P3.0/RXD

31 32 30 29 28 43 42 27 26 25 24 23 22 21 20

R49

R50

R51

R57

(PWR_SEL)
KEY3 R58 0/6

R28 1K/6
2

R190 R173

NC/1K/6 1K/6

HOTKEY_M PWR KEY3 DDC_WP KEY2 KEY1

XI

R29 2K/6

C17 DDC_WP 0.1U/6

PAGE1 VGA INPUT

DDC_SDA 16 CN4 11

L5

19/CX190T06009/6 R70 R71 C20 10pF/6 R72 100/6 C21 0.047u/6 100/6 C19 0.047u/6 R1+

RED+IN

RED-IN 1 6 2 7 3 8 4 9 5 10 RED+IN RED-IN GREEN+IN GREEN-IN BLUE+IN BLUE-IN 1 2 D33 EGA10603V05A1-B/NC L6

75/6/F 19/CX190T06009/6

R1-

DDC_SDA 12 IN-H
D

GREEN+IN
DSUB_5V R74 1 2 D32 EGA10603V05A1-B/NC C23 10pF/6 GREEN-IN L7 75/6/F 19/CX190T06009/6

R73

100/6

C22

0.047u/6

13 14

G1+
D

IN-V

DDC_SCL 15
17

DSUB_5V
DSUB_DET

DSUB_5V

R75

100/6

C24

0.047u/6

G1-

VGA

BLUE+IN
C27 R79 10pF/6 BLUE-IN 75/6/F L4 IN-H 19/CX190T06009/6 R81 R82 2K/6

R78

100/6

C26

0.047u/6

B1+

DGND

5DVCC 1 R80 100/6 C28 0.047u/6 B1-

DSUB_5V 2 D27 BAT54C/NC DSUB_5VCC 3 1 R174 4K7/6/NC 1 R175 4K7/6/NC U9 2 2

DDC_SCL

2007.12.07 change for EMI

100/6 C29 22P/6

AHS1

IN-V
R84
C

R83

100/6 C30 22P/6

AVS1

3DVCC

2K/6

DDC_SCL R176 1 DDC_SDA R177 1

2 100/6/NC 2 100/6/NC

6 5 1 2 3

SCL SDA NC0 NC1 NC2 24C02/NC

VCC WP GND

8
C

7 4

DDC_WP 1 C69 0.1uF/6/NC 2

D9 DAN217K/NC

D10 DAN217K/NC

D11 DAN217K/NC

RED+IN

GREEN+IN

BLUE+IN

3 5DVCC 1

(DVI-5V) Bus_Power 2 D28 BAT54C/NC DVI_5VCC 3 1 R178 4K7/6/NC 1 R179 4K7/6/NC U10 2 2

TX1+
1 2 D21 EGA10603V05A1-B/NC D12 EGA10603V05A1-B/NC 1 2 D13 EGA10603V05A1-B/NC 1 2 D23 EGA10603V05A1-B/NC 1 2 D24 EGA10603V05A1-B/NC 1 2 D25 EGA10603V05A1-B/NC 1 2 D26 EGA10603V05A1-B/NC 1 2 D19 EGA10603V05A1-B/NC 1 2 D20 EGA10603V05A1-B/NC 1 2 D22 EGA10603V05A1-B/NC

IN-H
2

IN-V

TX0-

TX0+

TXC+

TXC-

TX2-

TX2+

TX1-

EMI

DDC2_SCL DDC2_SDA
B

R180 1 R181 1

2 100/6/NC 2 100/6/NC

6 5 1 2 3

SCL SDA NC0 NC1 NC2 24C02/NC

VCC WP GND

8
B

CN5

2007.12.07 change for EMI

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 C31 0.1u/6 TX2TX2+

7 4

DDC_WP 1 C70 0.1uF/6/NC 2

25 31

RX2RX2+ GND RX4RX4+ SCL SDA VS RX1RX1+ GND RX3RX3+ 5V GND HP RX0RX0+ GND RX5RX5+ GND RXC+ RXC-

TX2TX2+

DDC2_SCL DDC2_SDA

EDID EEPROM(NC);IF EDID MCU DDCRAM NC

DDC2_SCL DDC2_SDA

DDC2_SCL
1 2 D17 EGA10603V05A1-B/NC TX1TX1+ Bus_Power (DVI-5V)

DDC2_SDA
2 D18 EGA10603V05A1-B/NC

DDC_SDA
1 2 D14 EGA10603V05A1-B/NC

DDC_SCL
2 D15 EGA10603V05A1-B/NC 1

TX1TX1+

Bus_Power
R86 100/6 R85 10K/6 Hot_Plug DVI_DET Hot_Plug

Bus_Power

TX0TX0+

TX0TX0+

2007.12.07 change for EMI

2 D34 EGA10603V05A1-B/NC 1 2 D16 EGA10603V05A1-B/NC 1 2 D36 EGA10603V05A1-B/NC TXC+ TXC-

TXC+ TXC-

DVI-D
5 4 3 2 1

32 26

3 C
TX0+ TX0TX1+ TX1TX2+ TX2TXC+ TXCB1B1+ G1G1+ R1R1+ AHS1 AVS1 DDC2_SCL DDC2_SDA RTD_SCLK RTD_SD3/SDI TX0+ TX0TX1+ TX1TX2+ TX2TXC+ TXCB1B1+ G1G1+ R1R1+ AHS1 AVS1 DDC2_SCL DDC2_SDA 100/6 100/6 R110 R111 DDCSCL_HDCP DDCSDA_HDCP

3 C

5DVCC

R183
RTD2525LH/2545LH 0 ohm RTD2545LR with OD NC

R185
NC 0 ohm

C73
NC 0.1uF

2N3904 SOT23
B 1 3 D E 2

2N3906 SOT23
B 1 3 C E 2

L11 120/CX201209813/8 2 R93 C32 1 10K/6 1U/8 Q10 AO3415 3 C43 2200P/6 R94 10K/6 PANEL_VCC C44 0.1u/6 EC6 100UF/16V
D

PANEL_VCC

2007.11.14 modify;reserve for 2545LR

R3.3VCC R1.8DVCC R1.8DVCC R185 R183 0/6/NC 0/6 R3.3VCC

AOS3415L SOT23
G 2
DGND

CHDTC144 SOT323
B 2 E 1

R92 2K2/6

C33 1U/8

C74 0.1u/6

C73 0.1u/6/NC DGND

S 1

RTD_SCLK DGND RTD_SD3/SDI XI XI DDCSDA_HDCP DDCSCL_HDCP

U7U7-1 Co-Lay. U7: QFN package; Q7-1:QFP package

3 R95 1 10K/6 PANEL_PW12 Q6 2N3904 DDCSCL_HDCP DDCSDA_HDCP

RTD_SD3/SDI

RTD_SD3/SDI

TMDS_VCC

TMDS_VCC

RTD_SCLK

RTD_SCLK

R1.8DVCC

TX2+

DGND2

TX2+

DGND2

TX2-

RXE0+

TX2-

1.8DVCC R1.8AVCC L8 120/CX201209813/8 R1.8AVCC

TMDS_VCC 48 47 U7

RXE0+

XI

RXE0-

RXE0-

modify T1 112107
CN8 CONN FFC-30/NC

XI

U7-1

TXO0-

TMDS_VDD

DDCSCL/PWM0

TMDS_VDD

V0/RX2N

V0/RX2N

DDCSCL/PWM0

VCLK/RX2P

VCLK/RX2P

TXO0+

TXO0-

PGND

PGND

SCL

SDA

SCL

VCCK

SDA

VCCK

DDCSDA/PWM1/IRQ

EC7 + 100uF/16V

C50 0.1u/6

R99 1K/6 1%

DDCSDA/PWM1/IRQ

TXO0+

0.1u/6 C49

RXE0RXE0+ RXE1RXE1+ RXE2RXE2+ DGND TXO1TXO1+ TXO2TXO2+ 36 35 34 33 32 31 30 29 28 27 26 25 RXE1RXE1+ RXE2RXE2+ RXECRXOCRXEC+ RXOC+ RXE3RXE3+ RXO0RXO0+ RXO1RXO1+ PANEL_VCC PANEL_VCC R100 R101 0/6/NC 0/6/NC RXO2RXO2+ RXOCRXOC+ RXO3RXO3+ DGND P26 P27 RXO1RXO1+ DGND RXECRXEC+ RXE3RXE3+ RXO0RXO0+ DGND

46

45

44

43

42

41

40

39

38

37

48

47

46

45

44

43

42

41

40

39

38

37

If U7=2545LR R99=6.2K
DGND TX1+

RXET

1 2

V1/REXT V2/RX1P V3/RX1N V4/RX0P V5/RX0N V6/RXCP V7/RXCN AVS AHS ADC_GND B-

TXO1TXO1+ TXO2TXO2+

36 35 34 33 32 31 30 29 28 27 26 25

RXE1RXE1+ RXE2RXE2+ RXECRXOCRXEC+ RXOC+ RXE3RXE3+ RXO0RXO0+ RXO1RXO1+

RXET TX1+ TX1TX0+ TX0TXC+ TXCAVS1 AHS1 DGND B1B1+

1 2 3 4 5 6 7 8 9 10 11 12

V1/REXT V2/RX1P V3/RX1N V4/RX0P V5/RX0N V6/RXCP V7/RXCN AVS AHS ADC_GND BB+ G+ R+ GR-

TX1C

3 4 5 6 7 8 9 10 11 12

1.8DVCC R1.8DVCC L10 120/CX201209813/8 R1.8DVCC

TX0+ TX0TXC+

RTD2525LH

TXOCTXOC+ TXO3TXO3+ TXE0TXE0+ TXE1-

RTD2545LH/NC

TXOCTXOC+ TXO3TXO3+ TXE0TXE0+ TXE1-

0.1u/6 C37

EC5 + 100uF/16V

C38 0.1u/6

TXCAVS1 AHS1

DGND 3DVCC 3DVCC

DGND B1B1+ R3.3VCC L23 R3.3VCC CX201209813/8/NC

ADC_VDD

TXE3+

TXE2+

TXE3+

TXE2+

BJT_B

BJT_B

PGND

PGND

TXE3-

TXE2-

TXE3-

L13 TMDS_VCC CX201209813/8

13

14

15

16

17

18

19

20

21

22

23

24

13

14

15

16

17

18

19

20

21

22

23

R1.8AVCC

R1.8AVCC

EC11 100uF/16V/NC

R1.8DVCC

DGND1

DGND1

RXO3+

RXO3+

EC10 100uF/16V

RXO3-

RXO2-

C75 0.1u/6/NC

G1+

G1+

R1+

G1-

G1-

R1-

R3.3VCC R1.8DVCC R189 R1.8DVCC R187 0/6/NC 0/6 R3.3VCC

B

DGND
B

DGND

2007.11.14 modify;reserve for 2545LR

C71 BJT_B 0.1u/6 R104 1K/6 1.8DVCC 3DVCC R105 470/6 R106 470/6 R107 470/6 R182 470/6/NC DGND C72 0.1u/6/NC DGND DGND

R1+

R1-

3 D
SN7002E CN6 RXE0RXE1RXE2DGND RXECRXE3RXO0DGND RXO1RXO2RXOCRXO3P27 PANEL_VCC 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 RXE0+ RXE1+ RXE2+ DGND RXEC+ RXE3+ RXO0+ DGND RXO1+ RXO2+ RXOC+ RXO3+ P26 PANEL_VCC PANEL_VCC

2007.11.14 modify;reserve for 2545LR

3 OUT

R187
RTD2525LH/2545LH 0 ohm NC RTD2545LR with OD

R189
NC 0 ohm

C72
NC 0.1uF

DTC144EUA

Q7 MMBT3906 2

IN 2

GND

3 1

RXO3-

RXO2-

BJT_B

BJT_B

C40 0.1u/6

RXO2+

RXO2+

24

TXE2-

TMDS_VCC

B+ G+ R+ GR-

TXE1+ VCCK

ADC_VDD

TXE1+ VCCK

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

XIN

XIN

Q8 MMBT3906 2

PANEL_VCC

1841 30P

Q9 MMBT3906 2

3 C
3 MMBT3906

Q13 MMBT3906/NC 2

B
3

E
A

2525LH :2x 3906 2545LH :3x 3906 2545LR(OD function):4x 3906 IF U2(U2-1) ;(this part NC,R104)

5DV AL1 1 2

VDD VDD AR1 4.7K/6/NC AR14 0/6/NC 3 AR2 10K/6/NC AR3 0/6/NC VOLU
D

120/CX201209813/8/NC

AC1 AC2 0.1u/6/NC 100uF/16V/NC

AGND VOLUME 2

AC3 1U/8/NC

PC AUDIO-IN

AQ1 DTC144EUA/NC

AR5 30K/6/NC

2007/01/16 for EMI solution

2007.11.14 modify
AU1 AGND AJ1 1 2 3 4 5 ZD005D100/NC R_LINE L_LINE AL4 120/CX201209813/8/NC AR7 1 2 Z0415 1 2 Z0416 AR9 AL5 120/CX201209813/8/NC 100/6/NC 100/6/NC RIN_PC LIN_PC AC4 AC5 0.47U/16V/6/NC 0.47U/16V/6/NC VDD AC8 220P/6/NC
C

VDD AR6 10K/6/NC 4 8 RIN+ LIN+ SE/~BTL VOLUME 19 18 VOLU AR8 1K/6/NC AGND 1 AL3 120/CX201209813/8/NC 2

AC6 220P/6/NC

AR10 20K/6/NC

AR11 20K/6/NC

3 AC7 0.47U/6/NC AC9 1 + 330uF/16V/NC 1 2

PVDD

BYPASS ~FADE

16 15 AGND AGND SHOUTDOWN 1 2 4606-04-04P-R 20 4 3 2 1 4 3 2 1 ACN1 1 AC10 0.47U/16V/6/NC

AGND

PGND ~SHOUTDOWN RINROUTVDD ROUT+ LINLOUT10 14

AGND AGND

AGND 5 AC11 VDD 0.47U/16V/6/NC VDD 6 AC12 0.47U/16V/6/NC AC13 0.47U16V/6/NC VDD AGND 7

AL2 120/CX201209813/8/NC 2

AGND

VDD AR12
B

9 AC14 11

PVDD AGND LOUT+ 12

AL6 120/CX201209813/8/NC 2

PGND

NC

10K/6/NC 3

AR13

10K/6/NC

SHOUTDOWN

0.47U/16V/6/NC

SPEAKER OUT
AC15 AC16 AC17 AC18 2006/10/19 0.1U/6/NC 0.1U/6/NC0.1U/6/NC0.1U/6/NC

AGND
B

13

AGND CHDTC144EUPT/NC

TPA6021A4/NC

STBY

AGND AQ2 AGND 1 AGND AGND AGND

17

AGND

2007/12/10

EMI

CN1
D

10 9 8 7 6 5 4 3 2 1 4401-E10-10P-R

MENU AUTO POWER E COLOR RIGHT LEFT AMBER GREEN 3 LED1 LED Dual 1 D1 DIODE DIAC

SW4 3 1 4 2 HDK632A SW5 3 1 4 2 HDK632A SW1 3 1 4 2 HDK632A SW6 3 1 4 2 HDK632A SW3 3 1 4 2 HDK632A SW2 3 1 4 2 HDK632A

MENU/SELECT

Button Board
D

AUTO/EXIT

POWER

E COLOR

RIGHT

LEFT

LED PIN 1,3 SWAP

C C

H1 2 3 4 5 9 8 7 6 2 3 4 5

H2 9 8 7 6

MTH276D126

MTH276D126

FRONT VIEW LED1 POWER + MENU AUTO E 11 SW1

A

SW2

SW3

SW4

SW5

SW6
A

Power Board

7 5 3

4 6