A785GM-A Manual2

Preface
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Version 1.0A
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp. AMD, Phenom, Athlon, Sempron and Duron are registered trademarks of AMD Corporation. Other product names used in this manual are the properties of their respective owners and are acknowledged.
Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the systems manufacturer could void the users authority to operate the equipment.
Preface
ii
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.
Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interferencecausing Equipment Regulations. Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilieur du Canada.
About the Manual

The manual consists of the following:
Chapter 1 Introducing the Motherboard Chapter 2 Installing the Motherboard Chapter 3 Using BIOS Chapter 4 Using the Motherboard Software Chapter 5 Hybrid Graphics Technology Support Chapter 6 Setting Up AMD SB710 RAID Configuration Chatper 7 Setting Up eJIFFY Chatper 8 Trouble Shooting
Describes features of the motherboard. page 1 Go to
Describes installation of motherboard components. page 7 Go to
Provides information on using the BIOS Setup Utility. Go to page 27
Describes the motherboard software Go to
page 47
Describes the Hybrid Graphics Technology Go to
page 55
Describes the AMD SB710 RAID Configuration Go to

page 59
Describes the eJIFFY setting up Go to page 67
Provides basic trouble shooting tips Go to page 85
Preface
iii
TABLE OF CONTENTS
Preface Chapter 1 i 1
Introducing the Motherboard 1 Introduction............................................................................................1 Features...................................................................................................2 Motherboard Components...................................................................4
Chapter 2
Installing the Motherboard 7 Safety Precautions...............................................................................7 Choosing a Computer Case..................................................................7 Installing the Motherboard in a Case.................................................7 Checking Jumper Settings....................................................................8
Setting Jumpers...............................................................................8 Checking Jumper Settings...............................................................9 Jumper Settings...............................................................................9
Installing Hardware..........................................................................10
Installing the Processor.................................................................10 Installing Memory Modules...........................................................11 Expansion Slots.............................................................................15 Connecting Optional Devices........................................................17 Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive............20 Installing a Floppy Diskette Drive................................................21
Connecting I/O Devices......................................................................22 Connecting Case Components..........................................................23

Front Panel Header.......................................................................25
Chapter 3
27
Using BIOS 27 About the Setup Utility....................................................................27

The Standard Configuration..........................................................27 Entering the Setup Utility...............................................................27 Resetting the Default CMOS Values...............................................28
Using BIOS............................................................................................29
Standard CMOS Setup..................................................................30 Advanced Setup.............................................................................32 Advanced Chipset Setup................................................................34
iv
Integrated Peripherals.................................................................35 Power Management Setup.............................................................36 PCI/PnP Setup..............................................................................37 PC Health Status...........................................................................38 M.I.B. (MB Intelligent BIOS)........................................................41 Load Default Settings....................................................................44 Supervisor Password....................................................................44 User Password..............................................................................45 Save & Exit Setup .........................................................................45 Exit Without Saving.......................................................................45 Updating the BIOS........................................................................46
Chapter 4
47
Using the Motherboard Software 47 About the Software DVD-ROM/CD-ROM....................................47 Auto-installing under Windows XP/Vista/7....................................47
Running Setup...............................................................................48
Manual Installation..........................................................................50 Utility Software Reference................................................................50
Chapter 5
55
Hybrid Graphics Technology Support 55 Hybrid Graphics Technology.........................................................55
Chapter 6
59
Setting Up AMD SB710 RAID Configuration 59 Setting Up a Bootable RAID Array...................................................59
Chapter 7
67
Setting Up eJIFFY 67 Introduction..........................................................................................67 Installation and BIOS Setup.................................................................68 Entering eJIFFY.............................................................................................71 Features Icons...........................................................................................72 Usage FAQ.................................................................................................73
Chapter 8
85
Trouble Shooting 85 Start up problems during assembly.......................................................85 Start up problems after prolong use.................................................86 Maintenance and care tips..................................................................86 Basic Troubleshooting Flowchart...................................................87
Chapter 1 Introducing the Motherboard Introduction

Thank you for choosing this motherboard. This motherboard is a high performance, enhanced function motherboard that supports AMD Phenom II/Phenom/Athlon II/Athlon /Sempron processors for high-end business or personal desktop markets. The motherboard incorporates the AMD 785G Northbridge (NB) and SB710 Southbridge (SB) chipsets. The Northbridge supports the HyperTransportTM 3.0 interface. The memory controller supports DDR2 memory DIMM frequencies of 1333/1066. It supports four DDR2 slots with maximum memory size of 32 GB*. One PCI Express x16 slot, intended for Graphics Interface, are fully compliant to the PCI Express Gen2 (version 2.0). In addition, two PCI Express x1 slots are supported. The SB710 Southbridge supports one PCI slot which is PCI v2.3 compliant. It integrates USB 2.0 interface, supporting up to twelve functional ports (six USB ports and three USB 2.0 headers support additional six USB ports). One onboard IDE connector supports two IDE devices in Ultra ATA 133/100/66/33 modes. The Southbridge integrates a Serial ATA host controller, supporting six SATA ports with maximum transfer rate up to 3.0 Gb/s each. It provides AMD SATA RAID configuration with RAID 0, 1 and 10 modes supported. There is an advanced full set of I/O ports in the rear panel, including PS/2 mouse and keyboard connectors, one VGA port, one HDMI port, six USB ports, one eSATA port, one LAN port and audio jacks for microphone, line-in and 8-ch line-out.
Introducing the Motherboard
Feature Processor
This motherboard uses a AMD socket that carries the following features: AMD Phenom II/Phenom/Athlon II/Athlon /Sempron proces sors Supports HyperTransport TM (HT) 3.0 interface speeds
HyperTransportTM Technology is a point-to-point link between two devices, it enables integrated circuits to exchange information at much higher speeds than currently available interconnect technologies.
Chipset
The AMD 785G Northbridge (NB) and SB710 Southbridge (SB) chipsets are based on an innovative and scalable architecture with proven reliability and performance. AMD 785G (NB) One x4 A-Link Express II interface for connection to an AMD Southbridge Supports PCIe Gen 2 (version 2.0) Proven RadeonTM graphics powering DirectX 10.1 Enhanced Digital Display integration Fully ACPI 2.0 and IAPC (Instantly Available PC) power management Single chip solution in 55nm, 1.1 V CMOS technology Integrated ATI Hybrid CrossFire, ATI AvivoTM HD1, AMD Cool'n'Quiet TM , ATI SurroundView TM, AMD OverDrive and AMD PowerNow! Compliant with PCI 2.3 specification at 33 MHz Supports six Serial ATA devices which speeds up to 3.0 Gb/s Integrated USB 2.0 Host Controller supporting up to twelve USB 2.0 ports Integrated IDE controller supports Ultra ATA 133/100/ 66/33 modes Supports integrated RAID0, RAID1, and RAID 10 (requires use of 4 or more SATA ports) functionalities across all 6 ports
SB710 (SB)
Memory
Supports DDR2 1066 (AM2+)/800/667/533/400 DDR SDRAM with Dual-channel architecture Accommodates four unbuffered DIMMs Up to 2 GB per DIMM with maximum memory size up to 8 GB 7.1 Channel High Definition Audio Codec SPDIF Out supports 96K/88.2K/48K/44.1KHz Power support: Digital:3.3V; Analog:5.0V MAxx PlayerTM from Waves Provides single ended CD input with DRM solutions and legacy OS issues Supports PCI ExpressTM 1.1 Integrated 10/100/1000 transceiver Wake-on-LAN and remote wake-up support
Audio
Onboard LAN

Expansion Options
The motherboard comes with the following expansion options: One PCI Express x16 for Graphics Interface Two PCI Express x1 slot Three 32-bit PCI v2.3 compliant slots One IDE connector supporting up to two IDE devices One floppy disk drive interface Five 7-pin SATA connectors This motherboard supports Ultra DMA bus mastering with transfer rates of 133/100/66/33 MB/s.
Integrated I/O
The motherboard has a full set of I/O ports and connectors: Two PS/2 ports for mouse and keyboard One VGA port One HDMI port One eSATA port Six USB ports One LAN port Audio jacks for microphone, line-in and 8-ch line-out
BIOS Firmware
The motherboard uses AMI BIOS that enables users to configure many system features including the following: Power management Wake-up alarms CPU parameters CPU and memory timing The firmware can also be used to set parameters for different processor clock speeds. 1. Some hardware specifications and software items are subject to change without prior notice. 2. Due to chipset limitation, we recommend that motherboard be operated in the ambiance between 0 and 50C.
Motherboard Components
Table of Motherboard Components

LABEL 1. CPU Socket 2. CPU_FAN 3. DRR2_1~4 4. ATX_POW ER 5. FDD 6. IDE 7. SPK 8. CLR_CMOS 9. SATA1~5 10. PW R_BOT 11. USB_PW R2 12. F_PANEL 13. RST_BOT 14. F_USB1~3 15. COM 16. SPDIFO 17. CD_IN 18. F_AUDIO 19. PCI1~3 20. PCIEX16 21. PCIE1~2 22. NB_FAN 23. SYS_FAN 24. USB_PW R3 25. USB_PW R1 26. ATX12V1 COMPONENTS AMD Phenom TM II/Phenom TM /Athlon TM II/Athlon TM / Sempron TM processors CPU cooling fan connector 240-pin DDR2 SDRAM slots Standard 24-pin ATX power connector Floppy disk connector Primary IDE connector Speaker header Clear CMOS jumper Serial ATA connectors Reset button USB Power Select Jumper Front panel switch/LED header Power on button Front Panel USB headers Onboard Serial port header SPDIF out header Analog audio input header Front panel audio header 32-bit add-on card slots PCI Express x16 slot for graphics interface PCI Express x1 slots Northbridge cooling fan connector System cooling fan connector USB Power Select Jumper USB Power Select Jumper 4-pin +12V power connector
This concludes Chapter 1. The next chapter explains how to install the motherboard.
Memo
Chapter 2 Installing the Motherboard Safety Precautions

Follow these safety precautions when installing the motherboard Wear a grounding strap attached to a grounded device to avoid damage from static electricity Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard Leave components in the static-proof bags they came in Hold all circuit boards by the edges. Do not bend circuit boards
Choosing a Computer Case

There are many types of computer cases on the market. The motherboard complies with the specifications for the ATX system case. Firstly, some features on the motherboard are implemented by cabling connectors on the motherboard to indicators and switches on the system case. Make sure that your case supports all the features required. Secondly, this motherboard supports one floppy diskette drive and two enhanced IDE drives. Make sure that your case has sufficient power and space for all drives that you intend to install. Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O template in the case matches the I/O ports installed on the rear edge of the motherboard. This motherboard carries an ATX form factor of 305 X 220 mm. Choose a case that accommodates this form factor.
Installing the Motherboard in a Case

Refer to the following illustration and instructions for installing the motherboard in a case. Most system cases have mounting brackets installed in the case, which correspond the holes in the motherboard. Place the motherboard over the mounting brackets and secure the motherboard onto the mounting brackets with screws. Ensure that your case has an I/O template that supports the I/O ports and expansion slots on your motherboard.
Installing the Motherboard
Do not over-tighten the screws as this can stress the motherboard.
Checking Jumper Settings

This section explains how to set jumpers for correct configuration of the motherboard.
Setting Jumpers
Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on the correct pins. The illustrations show a 2-pin jumper. When the jumper cap is placed on both pins, the jumper is SHORT. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is OPEN. This illustration shows a 3-pin jumper. Pins 1 and 2 are SHORT.
SHORT
OPEN
Checking Jumper Settings

The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled.
Jumper Settings
Jumper Type Description Setting (default) 1-2: NORMAL CLR_CMOS 3-pin Clear CMOS 2-3: CLEAR CMOS Before clearing the CMOS, make sure to turn off the system. 1-2: VCC5 2-3: 5VSB
1 CLR_CMOS 1 USB_PWR1
USB_PWR1 3-pin
USB Power Cotroller
USB_PWR2
3-pin
USB Power Cotroller
1-2: VCC5 2-3: 5VSB
1 USB_PWR2 1 USB_PWR3
USB_PWR3 3-pin
USB Power Cotroller
1-2: VCC5 2-3: 5VSB
1. To avoid the system unstability after clearing CMOS, we recommend users to enter the main BIOS setting page to Load Default Settings and then Save & Exit Setup. 2. Make sure the power supply provides enough 5VSB voltage before selecting the 5VSB function. 3. It is required that users place the USB_PWR1 & USB_PWR2 & USB_PWR3 cap onto 2-3 pin rather than 1-2 pin as default if you want to wake up the computer by USB/PS2 KB/Mouse.
10
Installing Hardware
Installing the Processor
Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface-mount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components. On most motherboards, there are small surface-mount resistors near the processor socket, which may be damaged if the cooling fan is carelessly installed. Avoid using cooling fans with sharp edges on the fan casing and the clips. Also, install the cooling fan in a well-lit work area so that you can clearly see the motherboard and processor socket.
Before installing the Processor

This motherboard automatically determines the CPU clock frequency and system bus frequency for the processor. You may be able to change these settings by making changes to jumpers on the motherboard, or changing the settings in the system Setup Utility. We strongly recommend that you do not over-clock processors or other components to run faster than their rated speed. Warning: 1. Over-clocking components can adversely affect the reliability of the system and introduce errors into your system. Over-clocking can permanently damage the motherboard by generating excess heat in components that are run beyond the rated limits. 2. Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components. This motherboard has a Socket AM3/AM2+ processor socket. When choosing a processor, consider the performance requirements of the system. Performance is based on the processor design, the clock speed and system bus frequency of the processor, and the quantity of internal cache memory and external cache memory.
11
CPU Installation Procedure

The following illustration shows CPU installation components. 1 2 Install your CPU. Pull up the lever away from the socket and lift up to 90-degree angle. Locate the CPU cut edge (the corner with the pin hold noticeably missing). Align and insert the CPU correctly. Press the lever down and apply thermal grease on top of the CPU. Put the CPU Fan down on the retention module and snap the four retention legs of the cooling fan into place. Flip the levers over to lock the heat sink in place and connect the CPU cooling Fan power cable to the CPUFAN connector. This completes the installation.
3 4
To achieve better airflow rates and heat dissipation, we suggest that you use a high quality fan with 4800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of CPU fan/heatsink supplied. The form and size of fan/heatsink may also vary.
Installing Memory Modules

This motherboard accommodates four memory modules. It can support four 240-pin DDR2 1066 (AM2+)/800/667/533/400. The total memory capacity is 8 GB.
DDR2 SDRAM memory module table

Memory module Memory Bus
DDR2 DDR2 DDR2 DDR2 DDR2
400 533 667 800 1066
200 266 333 400 533
MHz MHz MHz MHz MHz
You must install at least one module in any of the four slots. Each module can be installed with 2 GB of memory. Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges. Do not touch the components or metal parts. Always wear a grounding strap when you handle the modules.
12
Installation Procedure
Refer to the following to install the memory modules. 1 2 3 This motherboard supports unbuffered DDR2 SDRAM only. Push the latches on each side of the DIMM slot down. Align the memory module with the slot. The DIMM slots are keyed with notches and the DIMMs are keyed with cutouts so that they can only be installed correctly. Check that the cutouts on the DIMM module edge connector match the notches in the DIMM slot. Install the DIMM module into the slot and press it firmly down until it seats correctly. The slot latches are levered upwards and latch on to the edges of the DIMM. Install any remaining DIMM modules.
4 5
For best performance and compatibility, we recommend that users install DIMMs in the sequence of DIMM3, DIMM4, DIMM1 and DIMM2.
Recommend configuration for best performance and compatibility

Number of DIMMs DIMM 1 DIMM 2 DIMM 3 DIMM 4 AM2 Single Channel Dual Channel Single Channel Dual Channel
1 2 3 4
AM2+ * Unganged Mode Ganged Mode Unganged Mode Ganged Mode
: operation with normal performance : operation with the best performance
13
Table A: DDR2 (memory module) QVL (Qualified Vendor List)

The following DDR2 1066(AM2+) /800/667/533/400 memory modules have been tested and qualified for use with this motherboard.
Type
DDR2 533
Size
1 GB 512 MB
Vendor
A-data Micron Apacer Corsair Kingston
Module Name
Vitesta MT4HTF6464AY-667E1 AU01GE667C5KBGC 78.01G9O.9K5 VS1GB667D2 KVR667D2N5 MT8HTF12864AY-667E1 AL7E8E63B-6E1T AL7E8F63J-6E1 AL7E8F73C-6E1 Golden Bar M378T2863DZS 0742 78.A1G9O.9K4 HYMP125U64AP8-Y5 AB-A 0623 KVR667D2N5/2G PC2-5300U AL8E8F73C-6E1 M2GVD6G3I41P0U1E5E AU01GE800C5KBGC 78.01GAO.9K5 78.01GA0.9L5 Geil Millenary HYMP112U64CP8-S6 AB KLDD48F-B8KU5 NGES KVR800D2N5/1G 1.8V 9905316-054.A01LF NT1GT64U88D0BY-AD RML1320EH38D7F-800 Golden Bar M378T2953EZ3-CE7 0726 M378T2863EHS-CF7 0849 DIMM 5-5-5 GU341G0ALEPR6B2C6CE Red A-DATA M2OMI6H3J4720L1C5Z 78.A1GAO.9K4 78.A1GC0.9L4 CM2X2048-6400C5 Geil Platinum Edition HYMP125U64CP8-S6 AB KLDE88F-B8KU5 NHES KVR800D2N6/2G-SP KVR800D2N5/2G MT16HTF25664AY-800E1 NT2GT64U8HD0BY-AD AL8E8F73C-8E1 M378T5663QZ3-CF7 M378T5663EH3-CF7 GU342G0ALEPR692C6CE M378T5263AZ3-CF7 0819 MT8HTF12864AY-1GAE1 MT16HTF25664AY-1GAE1
1GB DDR2 667
Micron PSC Samsung Apacer Hynix Kingston LeadMax PSC A-DATA Apacer Geil Hynix KingMax Kingston Nanya Ramaxel Samsung Transcend Unifosa A-DATA
2GB
1 GB
DDR2 800
Apacer CORSAIR Geil Hynix KingMax
2 GB
Kingston Micron Nanya PSC Samsung Unifosa
DDR2 1066
4 GB 1 GB 2GB
Samsung Micron Micron
14
Due to the Phenom CPU and memory module limitation, the DRAM may need to adjust the voltage for supporting DDR2 1066. The memory modules which can be used stably are listed in the above QVL table for reference.
15
Expansion Slots
Installing Add-on Cards
The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboards features and capabilities. With these efficient facilities, you can increase the motherboards capabilities by adding hardware that performs tasks that are not part of the basic system.
PCIE1~2 Slots
The PCI Express x1 slots are fully compliant to the PCI Express Generation 2.0 (version 2.0). The PCI Express x16 slot is used to install an external PCI Express graphics card that is fully compliant to the PCI Express Generation 2.0 (version 2.0). This motherboard is equipped with three standard PCI slots. PCI stands for Peripheral Component Interconnect and is a bus standard for expansion cards, which for the most part, is a supplement of the older ISA bus standard. The PCI slots on this board are PCI v2.3 compliant. Before installing an add-on card, check the documentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation.
PCIEX16 Slot
PCI1~3 Slots
16
Follow these instructions to install an add-on card: 1 2 3 Remove a blanking plate from the system case corresponding to the slot you are going to use. Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot. Secure the metal bracket of the card to the system case with a screw.
For some add-on cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the add-on card.
17
Connecting Optional Devices

Refer to the following for information on connecting the motherboards optional devices:
COM: Onboard serial port header

Connect a serial port extension bracket to this header to add a serial port to your system.
Pin Signal Name DCDB SINB SOUTB DTRB GND DSRB RTSB CTSB RI Key Function Data Carrier Detect Serial Input UART B Serial Output UART B Data Terminal Ready Ground Data Set Ready RART B Request to Send Clear to Send Ring Indicator No pin
1 2 3 4 5 6 7 8 9 10
18
SATA1~5: Serial ATA connectors

These connectors are used to support the new Serial ATA devices for the highest data transfer rates (3.0 Gb/s), simpler disk drive cabling and easier PC assembly. It eliminates limitations of the current Parallel ATA interface. But maintains register compatibility and software compatibility with Parallel ATA.
Pin Signal Name Ground TXRXGround Pin Signal Name TX+ Ground RX+ -
1 3 5 7
2 4 6 -
SPDIFO: SPDIF out header

This is an optional header that provides an S/PDIF (Sony/Philips Digital Interface) output to digital multimedia device through optical fiber or coaxial connector.
Pin Signal Name SPDIF +5VA Key GND Function SPDIF digital output 5V analog Power No pin Ground
1 2 3 4
F_AUDIO: Front Panel Audio header

This header allows the user to install auxiliary front-oriented microphone and lineout ports for easier access.
Pin Pin Signal Name Signal Name PORT 1L PORT 1R PORT 2R SENSE_SEND PORT 2L Pin Signal Name Function AUD_GND PRESENCE# SENSE1_RETURN KEY SENSE2_RETURN
1 3 5 7 9
2 4 6 8 10
CD_IN: Analog audio input connector

Pin Signal Name CD_L GND GND CD_R Ground Ground Right CD-in signal Function Left CD-in signal
1 2 3 4
19
F_USB1~3: Front Panel USB headers

The motherboard has six USB ports installed on the rear edge I/O port array. Additionally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.
Pin Signal Name USBPWR USBPWR USB_FP_P0USB_FP_P1USB_FP_P0+ USB_FP_P1+ GND GND Key USB_FP_OC0 Function Front Panel USB Power Front Panel USB Power USB Port 0 Negative Signal USB Port 1 Negative Signal USB Port 0 Positive Signal USB Port 1 Positive Signal Ground Ground No pin Overcurrent signal
1 2 3 4 5 6 7 8 9 10
Please make sure that the USB cable has the same pin assignment as indicated above. A different pin assignment may cause damage or system hang-up.
20
Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive

This section describes how to install IDE devices such as a hard disk drive and a CDROM drive.
About IDE Devices

Your motherboard has one IDE interface. An IDE ribbon cable supporting two IDE devices is bundled with the motherboard. You must orient the cable connector so that the pin1 (color) edge of the cable corresponds to the pin 1 of the I/O port connector. IDE: IDE Connector This motherboard supports five high data transfer SATA ports with each runs up to 3.0 Gb/s. To get better system performance, we recommend users connect the CDROM to the IDE channel, and set up the hard drives on the SATA ports.
IDE devices enclose jumpers or switches used to set the IDE device as MASTER or SLAVE. Refer to the IDE device users manual. Installing two IDE devices on one cable, ensure that one device is set to MASTER and the other device is set to SLAVE. The documentation of your IDE device explains how to do this.
About SATA Connectors

Your motherboard features five SATA connectors supporting a total of five drives. SATA refers to Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE hard drives which are currently used in most PCs. These connectors are well designed and will only fit in one orientation. Locate the SATA connectors on the motherboard and follow the illustration below to install the SATA hard drives.
Installing Serial ATA Hard Drives

To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the Serial ATA protocol. This SATA cable comes with an SATA power cable. You can connect either end of the SATA cable to the SATA hard drive or the connector on the motherboard.
SATA cable
(optional)
SATA power cable
(optional)
21
Refer to the illustration below for proper installation: 1 2 3 Attach either cable end to the connector on the motherboard. Attach the other cable end to the SATA hard drive. Attach the SATA power cable to the SATA hard drive and connect the other end to the power supply.
This motherboard supports the Hot-Plug function.
Installing a Floppy Diskette Drive

FDD: Floppy Disk Connector
Connect the single end of the floppy connector to the onboard floppy connector firstly, and then connect the remaining plugs on the other end to the floppy drives correspondingly. You must orient the cable connector so that the pin 1 (color) edge of the cable corresponds to the pin 1 of the I/O port connector.
22
Connecting I/O Devices

The backplane of the motherboard has the following I/O ports:
PS2 Mouse PS2 Keyboard VGA Port HDMI Port USB Ports eSATA Port
Use the upper PS/2 port to connect a PS/2 pointing device. Use the lower PS/2 port to connect a PS/2 keyboard. Connect your monitor to the VGA port. Connect the HDMI port to the HDMI devices. Use the USB ports to connect USB devices. Use this port to connect to an external SATA box or a Serial ATA port multiplier. Connect an RJ-45 jack to the LAN port to connect your computer to the network. Use the audio jacks to connect audio devices. The D port is for stereo line-in signal, while the F port is for microphone in signal. This motherboard supports 8-channel audio devices that correspond to the A,B, C, and E port respectively. In addition, all of the 3 ports, B, C, and E provide users with both right & left channels individually. Users please refer to the following note for specific port function definition. A: Center & Woofer B: Back Surround C: Side Surround D: Line-in E: Front Out F: Mic_in Rear
LAN Port
Audio Ports
The above port definition can be changed to audio input or audio output by changing the driver utility setting.
23
Connecting Case Components

After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following: 1 2 3 4 5 6 7 Connect the CPU cooling fan cable to CPU_FAN. Connect the standard power supply connector to ATX_POWER. Connect the case speaker cable to SPK. Connect the case switches and indicator LEDs to the F_PANEL. Connect the system cooling fan connector to SYS_FAN. Connect the auxiliary case power supply connector to ATX12V1. Connect the northbridge cooling fan connector to NB_FAN.
Connecting 24-pin power cable

Users please note that the 24-pin power cable can be connected to the ATX_POWER connector.
With ATX v2.x power supply, users please note that when installing 24-pin power cable, the latches of power cable and the ATX_POWER match perfectly. 24-pin power cable
24
CPU_FAN: Cooling FAN Power Connector

Pin Signal Name GND +12V Sense PWM Function System Ground Power +12V Sensor CPU FAN control
1 2 3 4
Users please note that the fan connector supports the CPU cooling fan of 1.1A~2.2A (26.4W max.) at +12V.
ATX_POWER: ATX 24-pin Power Connector

Pin Signal Name +3.3V +3.3V Ground +5V Ground +5V Ground PWRGD +5VSB +12V +12V +3.3V Pin Signal Name +3.3V -12V COM PS_ON COM COM COM -5V +5V +5V +5V COM
1 2 3 4 5 6 7 8 9 10 11 12
13 14 15 16 17 18 19 20 21 22 23 24
SYS_FAN/NB_FAN: FAN Power Connectors

Pin Signal Name GND +12V Function
1 2 3
Sense
System Ground Power +12V Sensor
SPK: Internal speaker

Pin Signal Name VCC Key NC Signal
1 2 3 4
ATX12V1: ATX 12V Power Connector

Pin Signal Name Ground Ground +12V +12V
1 2 3 4
25
Front Panel Header

The front panel header (F_PANEL) provides a standard set of switch and LED headers commonly found on ATX or Micro ATX cases. Refer to the table below for information:
Pin 1 3 5 7 9
Signal
Function
Pin 4 6 8 10
Signal
Function
HD_LED_P Hard disk LED (+) 2 HD_LED_N Hard disk LED (-) RST_SW_N Reset Switch (-) RST_SW_P RSVD Reset Switch (+) Reserved
FP PWR/SLP *MSG LED (+) FP PWR/SLP *MSG LED (-) PWR_SW_P Power Switch (+) PWR_SW_N Power Switch (-) Key No pin
* MSG LED (dual color or single color)
Hard Drive Activity LED

Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that data is being read from or written to the hard drive. For the LED to function properly, an IDE drive should be connected to the onboard IDE interface. The LED will also show activity for devices connected to the SCSI (hard drive activity LED) connector.
Power/Sleep/Message waiting LED

Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides power on/off, sleep, and message waiting indication.
Reset Switch
Supporting the reset function requires connecting pin 5 and 7 to a momentarycontact switch that is normally open. When the switch is closed, the board resets and runs POST.
Power Switch
Supporting the power on/off function requires connecting pins 6 and 8 to a momentary-contact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off. The time requirement is due to internal de-bounce circuitry. After receiving a power on/off signal, at least two seconds elapses before the power supply recognizes another on/off signal.
This concludes Chapter 2. The next chapter covers the BIOS.
26
Memo
27
Chapter 3 Using BIOS About the Setup Utility

The computer uses the latest American Megatrends Inc. BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS. The BIOS (Basic Input and Output System) Setup Utility displays the systems configuration status and provides you with options to set system parameters. The parameters are stored in battery-backed-up CMOS RAM that saves this information when the power is turned off. When the system is turned back on, the system is configured with the values you stored in CMOS. The BIOS Setup Utility enables you to configure: Hard drives, diskette drives and peripherals Video display type and display options Password protection from unauthorized use Power Management features
The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options. This chapter provides explanations for Setup Utility options.
The Standard Configuration

A standard configuration has already been set in the Setup Utility. However, we recommend that you read this chapter in case you need to make any changes in the future. This Setup Utility should be used: when changing the system configuration when a configuration error is detected and you are prompted to make changes to the Setup Utility when trying to resolve IRQ conflicts when making changes to the Power Management configuration when changing the password or making other changes to the Security Setup
Entering the Setup Utility

When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are completed, the following message appears: Press DEL to enter SETUP
Using BIOS
28
Press the delete key to access the BIOS Setup Utility.
CMOS Setup Utility -- Copyright (C) 1985-2005, American Megatrends, Inc.
Standard CMOS Setup Advanced Setup Advanced Chipset Setup Integrated Peripherals Power Management Setup PCI/PnP Setup PC Health Status
: Move
M.I.B (MB Intelligent BIOS)

Load Default Settings
Supervisor Password User Password

Save & Exit Setup Exit Without Saving
Enter : Select +/-/: Value F10: Save F1:General Help F9: Optimized Defaults
ESC: Exit
v02.62 (C)Copyright 1985-2008, American Mega trends, Inc.
Resetting the Default CMOS Values

When powering on for the first time, the POST screen may show a CMOS Settings Wrong message. This standard message will appear following a clear CMOS data at factory by the manufacturer. You simply need to Load Default Settings to reset the default CMOS values. Note: Changes to system hardware such as different CPU, memories, etc. may also trigger this message.
Using BIOS
29
Using BIOS
When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>. Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for information. Some options (marked with a triangle ) lead to submenus that enable you to change the values for the option. Use the cursor arrow keys to scroll through the items in the submenu. In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a triangle . The default BIOS setting for this motherboard applies for most conditions with optimum performance. It is not suggested to change the default values in the BIOS setup and the manufacture takes no responsibility to any damage caused by changing the BIOS settings.
BIOS Navigation Keys

The BIOS navigation keys are listed below: KEY
ESC Exits the current menu Scrolls through the items on a menu Modifies the selected fields values Select Load a default optimized setting Saves the current configuration and exits setup Displays a screen that describes all key functions
FUNCTION
< >
+/Enter F9 F10 F1
Using BIOS
30
For the purpose of better product maintenance, the manufacture reserves the right to change the BIOS items presented in this manual. The BIOS setup screens shown in this chapter are for reference only and may differ from the actual BIOS. Please visit the manufactures website for updated manual.
Standard CMOS Setup

This option displays basic information about your system.
CMOS Setup Utility -- Copyright (C) 1985-2005, American Megatrends, Inc. Standard CMOS Setup Date Time IDE Master IDE Slave SATA1 SATA 2 SATA 3 SATA 4 SATA5 eSATA IDE BusMaster Drive A: Mon 11/02/2009 02:52:22 Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected Enabled 1.44 MB 31/2 Help Item User [Enter], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system Date.
: Move
Enter : Select +/-/: Value F10: Save ESC: Exit F1: General Help F9: Optimized Defaults
Date & Time The Date and Time items show the current date and time on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility. IDE Master This motherboard supports five SATA channels and each channel allows one SATA device to be installed. Use these items to configure each device on the SATA channel.
CMOS SETUP UTILITY Copyright (C) 1985-2005, American Megatrends, Inc. IDE Master SATA Device : Not Detected Auto Auto Auto Auto Auto Enabled Help Item Disabled: Disables LBA Mode. Auto: Enables LBA Mode if the device supports it and the device is not already formatted with LBA Mode disabled.
LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T 32Bit Data Transfer
: Move
Enter : Select +/-/: Value F10: Save ESC: Exit F1: General Help F9: Optimized Defaults
Using BIOS
31
LBA/Large Mode (Auto) Use this item to set the LAB/Large mode to enhance hard disk performance by optimizing the area the hard disk is visited each time. Block (Multi-Sector Transfer) (Auto) If the feature is enabled, it will enhance hard disk performance by reading or writing more data during each transfer. PIO Mode (Auto) Use this item to set the PIO mode to enhance hard disk performance by optimizing the hard disk timing. DMA Mode (Auto) DMA capability allows user to improve the transfer-speed and data-integrity for compatible IDE devices. S.M.A.R.T. (Auto) The S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) system is a diagnostics technology that monitors and predicts device performance. S.M.A.R.T. software resides on both the disk drive and the host computer. 32Bit Data Transfer (Enabled) Use this item to set the onboard SATA-IDE channel to be disabled, IDE, or RAID. Press <Esc> to return to the Standard CMOS Setup page.
IDE BusMaster (Enabled) This item enables or disables the DMA under DOS mode. We recommend you to leave this item at the default value. Drive A (Disabled) This item defines the characteristics of any diskette drive attached to the system. You can connect one or two diskette drives.
Press <Esc> to return to the main menu setting page.
Using BIOS
32
Advanced Setup
This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Advanced Setup Help Item AMD C&Q Enhanced Halt (CIE) Quick Power on Self Test Boot Up Numlock Status APIC Mode 1st Boot Device 2nd Boot Device 3rd Boot Device Removable Drives Boot Other Device ECS eJIFFY Function Auto Disabled Enabled On Enabled Hard Drive CD/DVD 1st FLOPPY DRIVE Press Enter Yes Disabled Enable/disable the generation of ACPI _PPC, _PPS, and _PCT objects.
: Move AMD C&Q (Auto)
Enter : Select +/-/: Value F10: Save ESC: Exit F1:General Help F9: Optimized Defaults
This item helps the system to lower the frequency when CPU idles. When the frequency decreases, the temperature will drop automatically as well. Enhanced Halt (C1E) (Disabled) This item enables or disables enhanced halt. Quick Power on Self Test (Enabled) Enable this item to shorten the power on testing (POST) and have your system start up faster. You might like to enable this item after you are confident that your system hardware is operating smoothly. Boot Up Numlock Status (On) This item defines if the keyboard Num Lock key is active when your system is started. APIC Mode (Enabled) This item allows you to enable or disable the APCI (Advanced Programmable Interrupt Controller) mode. APIC provides symmetric multi-processing (SMP) for systems, allowing support for up to 60 processors. 1st/2nd3rd Boot Device (Hard Drive/CD/DVD/1st Floppy DRIVE) Use this item to determine the device order the computer used to look for an operating system to load at start-up time. The devices showed here will be different depending on the exact devices installed on your motherboard.
Using BIOS
33
Removable Drives (Press Enter) Scroll to this item and press <Enter> to view the following screen:
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Removable Drives Removable Drives 1st Drive 1st FLOPPY DRIVE Help Item Specifies the boot sequence from the available devices.
: Move
Enter : Select F1:General Help
+/-/: Value F10: Save ESC: Exit F9: Optimized Defaults
Press <Esc> to return to the Advanced Setup page. Boot Other Device (Yes) When enabled, the system searches all other possible locations for an operating system if it fails to find one in the devices specified under the First, Second and Third boot devices. ECS eJIFFY Function (Disabled) Use this item to enable or disable the ECS eJIFFY Function. eJIFFY is ECS uniquesoftware program for the quick access to the internet without entering O.S. Pleaserefer to Chapter 7 to know more about eJIFFY.
Using BIOS
34
Advanced Chipset Setup

This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Advanced Chipset Setup Help Item Internal Graphics Mode GFX Clock Override Share Memory Size Init Display First Memory Hole Remapping HDMI Audio DCT Unganged Mode UMA Disabled Auto PCI Enabled Enabled Always Options Disabled UMA
: Move
+/-/: Value F10: Save F9: Optimized Defaults
ESC: Exit
Internal Graphics Mode (UMA) Use this item to choose the onboard VGA mode. You can select [Disabled] to disablethe onboard VGA, [UMA] to use the system memory.
Warning: If Disabled Internal Graphics Mode, please Loading default toEnable it.
GFX Clock Override (Disabled) Use this item to enable or disable GFX Clock Override. Share Memory Size (Auto) This item lets you allocate a portion of the main memory for the onboard VGA display application. Init Display First (PCI) Use this item to select which graphics controller to use as the primary boot devices. Memory Hole Remapping (Enabled) This item allows users to enable or disable memroy hole remapping. HDMI Audio (Enabled) This item is used to enable or disable the onboard audio chip. DCT Unganged Mode (Always) This item is used to select the DCT mode (DRAM Controller mode).
Using BIOS
35
Integrated Peripherals
This page sets up some parameters for peripheral devices connected to the system.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Integrated Peripherals Onboard IDE Controller Onboard SATA Mode SATA Configuration Onboard AUDIO Function Onboard LAN Function Onboard LAN Boot ROM Serial Port1 Address USB Functions Legacy USB Support Enabled Enabled IDE Enabled Enabled Disabled Disabled Enabled Enabled Help Item DISABLED: disables the integrated IDE Controller. Enabled: enables both Controllers.
: Move
Onboard IDE Controller (Enabled) Use this item to enable or disable the onboard IDE interface. Onboard SATA Mode (Enabled) Use this item to enable or disable the onboard SATA mode. SATA Configuration (IDE) Use this item to show the Serial ATA Configuration options: Disabled, Compatible, Enhanced. Onboard AUDIO Function (Enabled) Use this item to enable or disable the onboard Audio function. Onboard LAN Function (Enabled) Use this item to enable or disable the onboard LAN function. Onboard LAN Boot ROM (Disabled) Use this item to enable or disable the booting from the onboard LAN or a network add-in card with a remote boot ROM installed. Serial Port1 Address (Disabled) Use this item to enable or disable the onboard COM1 serial port, and to assign a port address. USB Functions (Enabled) Use this item to enable or disable the USB function. Legacy USB Support (Enabled) Use this item to enable or disable support for legacy USB devices. Setting to Auto allows the system to detect the presence of USB device at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled. Press <Esc> to return to the main menu setting page.
Using BIOS
36
Power Management Setup

This page sets up some parameters for system power management operation.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Power Management Setup Help Item Select the ACPI state used for System Suspend.
ACPI Suspend Type PWRON After PWR-Fail Resume By RING Resume By PCI/PCI-E/Lan PME Resume By USB (S3) Resume By PS2 KB (S3) Resume By PS2 MS (S3) Resume on RTC Alarm
S3 Power Off Disabled Disabled Disabled Disabled Disabled Disabled
: Move
+/-/: Value F10: Save F9: Optimized Defaults
ESC: Exit
ACPI Suspend Type (S3) Use this item to define how your system suspends. In the default, S3, the suspend mode is a suspend to RAM, i.e, the system shuts down with the exception of a refresh current to the system memory. PWRON After PWR-Fail (Power Off) This item enables your computer to automatically restart or return to its operating status. Resume By RING (Disabled) The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the Modem. You must use an ATX power supply in order to use this feature. Resume By PCI/PCI-E/Lan PME (Disabled) The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the PCI Modem or PCI LAN card. You must use an ATX power supply in order to use this feature. Use this item to do wake-up action if inserting the PCI card. Resume By USB (S3) (Disabled) This item allows you to enable/disable the USB device wakeup function from S3 mode.
Using BIOS
37
Resume By PS2 KB (S3) (Disabled) This item enables or disables you to allow keyboard activity to awaken the system from power saving mode. Resume By PS2 MS (S3) (Disabled) This item enables or disables you to allow mouse activity to awaken the system from power saving mode. Resume on RTC Alarm (Disabled) The system can be turned off with a software command. If you enable this item, the system can automatically resume at a fixed time based on the systems RTC (realtime clock). Use the items below this one to set the date and time of the wake-up alarm. You must use an ATX power supply in order to use this feature. Press <Esc> to return to the main menu setting page.
PCI / PnP Setup

This page sets up some parameters for devices installed on the PCI bus and those utilizing the system plug and play capability.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. PCI / PnP Setup Init Display First PCI Help Item Options PCI-E PCI
: Move
Init Display First (PCI) Use this item to select which graphics controller to use as the primary boot devices.
Using BIOS
38
PC Health Status
On motherboards support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. PC Health Status -=- System Hardware Monitor-=Smart Fan Function Press Enter Shutdown Temperature (CPU) Disabled CPU Temperature : 41C/105F CPU Fan Speed System FAN Speed CPU Vcore VDIMM : 4655 RPM : N/A : 1.424V : 1.936V Help Item
: Move
Smart Fan Function

Scroll to this item and press <Enter> to view the following screen:
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Smart Fan Function Help Item SMART FAN Control Smart Fan Mode SMART Fan start PWM value. SMART Fan start TEMP. (C) DeltaT1 SMART Fan Slope PWM value CPU FAN Full Limit Temp. Enabled Normal 43 27 +3 3 PWM value/C 55C Options Disabled Enabled
: Move
+/-/: Value
F10: Save
ESC: Exit
F9: Optimized Defaults
SMART FAN Control (Enabled) This item allows you to enable/disable the control of the system fan speed by changing the fan voltage. SMART Fan Mode (Normal) This item allows you to select the fan mode (Normal, Quiet, Silent, or Manual) for a better operation environment. If you choose Normal mode, the fan speed will be auto adjusted depending on the CPU temperature. If you choose Quite mode, the fan speed will be auto minimized for quiet environment. If you choose Silent mode, the fan speed will be auto restricted to make system more quietly. If you choose Manual mode, the fan speed will be adjust depending on users parameters.
Using BIOS
39
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Smart Fan Function Help Item SMART FAN Control Smart Fan Mode SMART Fan start PWM value. SMART Fan start TEMP. (C) DeltaT1 SMART Fan Slope PWM value CPU FAN Full Limit Temp. Enabled Quiet 20 52 +3 8 PWM value/C 65C Options Normal: auto adjusts depending on the CPU temperature. Quiet: auto minimizes fan speed for quiet environment operation.
: Move Enter : Select F1:General Help
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Smart Fan Function Help Item SMART FAN Control Smart Fan Mode SMART Fan start PWM value. SMART Fan start TEMP. (C) DeltaT1 SMART Fan Slope PWM value CPU FAN Full Limit Temp. Enabled Silent 5 60 +3 14 PWM value/C 68C Options Normal: auto adjusts depending on the CPU temperature. Quiet: auto minimizes fan speed for quiet environment operation.
: Move
Enter : Select
+/-/: Value
F10: Save
ESC: Exit
F1:General Help
F9: Optimized Defaults
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Smart Fan Function Help Item SMART FAN Control Smart Fan Mode SMART Fan start PWM value. SMART Fan start TEMP. (C) DeltaT1 SMART Fan Slope PWM value CPU FAN Full Limit Temp. Enabled Manual 43 27 +3 3 PWM value/C 55C Options Normal: auto adjusts depending on the CPU temperature. Quiet: auto minimizes fan speed for quiet environment operation.
: Move Enter : Select F1:General Help
Using BIOS
40
SMART Fan start PWM value (43) This item is used to set the start PWM value of the smart fan. SMART Fan start TEMP. (C) (27) This item is used to set the start temperature of the smart fan. DeltaT1 (+3) This item specifies the range that controls CPU temperature and keeps it from going so high or so low when smart fan works. SMART Fan Slope PWM value (4 PWM value/C) This item is used to set the Slope Select PWM of the smart fan. CPU FAN Full Limit Temp. (55C) This item is used to set the Slope Select PWM of the smart fan. Press <Esc> to return to the PC Health Status page.
Shutdown Temperature (CPU) (Disabled) Enable you to set the maximum temperature the CPU can reach before powering down System Component Characteristics These items display the monitoring of the overall inboard hardware health events, such as System & CPU temperature, CPU & DIMM voltage, CPU & system fan speed,...etc. CPU Temperature CPU Fan Speed System FAN Speed CPU Vcore VDIMM
Using BIOS
41
M.I.B. (MB Intelligent Bios)

This page enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have installed in your system.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. M.I.B.(MB Intelligent BIOS)
Memory Configuration
CPU Frequency Ctrl: HT Frequency CPU/HT Reference Clock (MHz) Auto Detect DIMM/PCI Clk Spread Spectrum CPU Voltage DIMM Voltage
Press Enter Disabled Auto 200 Enabled Enabled 0 12
Help Item
AMD Phenom (tm) II X3 715 Processor Speed :2800MHz, NB CLK: 1800MHz Current CPU Frequency Current CPU Voltage Current NB Frequency 2800MHz 1.4250v 1800MHz
: Move
ESC: Exit
Memory Configuration
Scroll to this item and press <Enter> to view the following screen:
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Memory Configuration Help Item Disabled Auto Auto XOR of Address bits Auto Limit Manual
Memory Configuration DRAM Frequency DRAM Timing Mode Bank Interleaving Channel Interleaving
Memory CLK : N/A, 333MHz CAS Latency (Tcl) : N/A, 5.0 RAS/CAS Delay (Trcd) : N/A, 5 CLK Row Precharge Time (Trp) : N/A, 5 CLK Min Active RAS (Tras) : N/A, 15 CLK RAS/RAS Delay (Trrd) : N/A, 3 CLK Row Cycle (Trc) : N/A, 20 CLK
: Move
ESC: Exit
Using BIOS
42
DRAM Frequency (Disabled) This item enables users to adjust the DRAM frequency. The default setting is auto and we recommend users leave the setting unchanged. Modify it at will may cause the system to be unstable. DRAM Timing Mode (Auto) This item enables you to specify the DRAM timing mode to be configured automatically or manually. Bank Interleaving (Auto) This item is used to set the bank interleaving. Channel Interleaving (XOR of Address bits) This item is used to set the channel interleaving. Memory CLK (N/A, 333 MHz) This item is used to set the memory clock mode. CAS Latency (Tcl) (N/A, 5.0) This item controls the timing delay (inclockcycles) before the DRAM starts a read command after receiving it. RAS/CAS Delay (Trcd) (N/A, 5 CLK) This is the amount of time a CAS is performed after a RAS. The lower the better, but some DRAM does not support low figures. Row Precharge Time (Trp) (N/A, 5 CLK) This item specifies the Row precharge to Active or Auto-Refresh of the same bank. Min Active RAS (Tras) (N/A, 15 CLK) This item determins the time RAS takes to read from and write to a memory cell. RAS/RAS Delay (Trrd) (N/A, 3 CLK) This item specifies the active-to-active delay of different banks. Row Cycle (Trc) (N/A, 20 CLK) Use this item to specify the Row Cycle Time. Press <Esc> to return to the M.I.B page. CPU Frequency Ctrl (Disabled) This item allows user to enable or disable CPU frequency control. HT Frequency (Auto) This item enables users to adjust the HT frequency. The default setting is auto and we recommend users leave the setting unchanged. Modify it at will may cause the system to be unstable. CPU/HT Reference Clock (MHz) (200) Use this item to set the CPU/HT Reference Clock through clock gen. Auto Detect DIMM/PCI Clk (Enabled) When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI slots. Spread Spectrum (Enabled) If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system.
Using BIOS
43
CPU Voltage (0) This item allows users to adjust the CPU voltage. DIMM Voltage (12) This item allows users to adjust the DIMM voltage. Incorrectly doing overclock/overvoltage may result in damage to CPU, chipset, or memory and reduce the useful life of these components. This function is for advanced users only and we recommend you not to alter the default settings to prevent system instability or other unexpected results. (Enable for AM2+ / Disable for AM2) AMD Athlon (tm) II x3715 Processor This is display-only field and displays the information of the CPU installed in your computer. NB CLK (1800 MHz) This item shows the frequency of Northbridge clock. Current CPU Frequency (2800 MHz) This item indicates the current CPU frequency. Users can not make any change tothis item. Please noted that the frequency will be varied with different CPU. Current CPU Voltage (1.4250v) This item indicates the current CPU voltage. Current NB Frequency (1800 MHz) This item indicates the current NB frequency.
Using BIOS
44
Load Default Settings

This option opens a dialog box to ask if you are sure to install optimized defaults or not. You select [OK], and then press <Enter>, the Setup Utility loads all default values; or select [Cancel], and then press <Enter>, the Setup Utility does not load default values.
Supervisor Password
This page helps you install or change a password.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Supervisor Password Supervisor Password :Not Installed Press Enter Help item Install or Change the password.
Change Supervisor Password
: Move
Supervisor Password (Not Installed) This item indicates whether a supervisor password has been set. If the password has been installed, Installed displays. If not, Not Installed displays. Change Supervisor Password (Press Enter) You can select this option and press <Enter> to access the sub menu. You can use the sub menu to change the supervisor password.
Using BIOS
45
User Password
This page helps you install or change a password.
CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. User Password User Password Change User Password : Not Installed Press Enter Help Item Install or Change the password.
: Move
User Password (Not Installed) This item indicates whether a user password has been set. If the password has been installed, Installed displays. If not, Not Installed displays. Change User Password (Press Enter) You can select this option and press <Enter> to access the sub menu. You can use the sub menu to change the user password. This item will show if the supervisor password is set. Press <Esc> to return to the main menu setting page.
Save & Exit Setup

Highlight this item and press <Enter> to save the changes that you have made in the Setup Utility and exit the Setup Utility. When the Save and Exit dialog box appears, select [OK] to save and exit, or select [Cancel] to return to the main menu.
Exit Without Saving

Highlight this item and press <Enter> to discard any changes that you have made in the Setup Utility and exit the Setup Utility. When the Exit Without Saving dialog box appears, select [OK] to discard changes and exit, or select [Cancel] to return to the main menu. If you have made settings that you do not want to save, use the Exit Without Saving item and select [OK] to discard any changes you have made.
Using BIOS
46
Updating the BIOS

You can download and install updated BIOS for this motherboard from the manufacturers Web site. New BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. Install new BIOS as follows: 1 2 If your motherboard has a BIOS protection jumper, change the setting to allow BIOS flashing. If your motherboard has an item called Firmware Write Protect in Advanced BIOS features, disable it. (Firmware Write Protect prevents BIOS from being overwritten.) Prepare a bootable device or create a bootable system disk. (Refer to Windows online help for information on creating a bootable system disk.) Download the Flash Utility and new BIOS file from the manufacturers Web site. Copy these files to the bootable device. Turn off your computer and insert the bootable device in your computer. (You might need to run the Setup Utility and change the the boot priority items on the Advanced BIOS Features Setup page, to force your computer to boot from the bootable device first.) At the C:\ or A:\ prompt, type the Flash Utility program name and the file name of the new BIOS and then press <Enter>. Example: AMINF340.EXE040706.ROM When the installation is complete, remove the bootable device from the computer and restart your computer. If your motherboard has a Flash BIOS jumper, reset the jumper to protect the newly installed BIOS from being overwritten. The computer will restart automatically.
4 5
This concludes Chapter 3. Refer to the next chapter for information on the software supplied with the motherboard.
Using BIOS
47
Chapter 4 Using the Motherboard Software About the Software DVD-ROM/CD-ROM

The support software DVD-ROM/CD-ROM that is included in the motherboard package contains all the drivers and utility programs needed to properly run the bundled products. Below you can find a brief description of each software program, and the location for your motherboard version. More information on some programs is available in a README file, located in the same directory as the software. Before installing any software, always inspect the folder for files named README.TXT or something similar. These files may contain important information that is not included in this manual. 1. Never try to install all software from folder that is not specified for use with your motherboard. 2. The notice of Intel HD Audio Installation (optional): The Intel High Definition audio functionality unexpectedly quits working in Windows Server 2003 Service Pack 1 or Windows XP Professional x64 Edition. Users need to download and install the update packages from the Microsoft Download Center before installing HD audio driver bundled in the driver CD. Please log on to http://support.microsoft.com/ default.aspx?scid=kb;en-us;901105#appliesto for more information.
Auto-installing under Windows XP/Vista/7

The Auto-install DVD-ROM/CD-ROM makes it easy for you to install the drivers and software for your motherboard. If the Auto-install DVD-ROM/CD-ROM does not work on your system, you can still install drivers through the file manager for your OS (for example, Windows Explorer). Refer to the Utility Folder Installation Notes later in this chapter. The support software DVD-ROM/CD-ROM disc loads automatically under Windows XP/Vista/7. When you insert the DVD-ROM/CD-ROM disc in the DVD-ROM/CDROM drive, the autorun feature will automatically bring up the install screen. The screen has three buttons on it, Setup, Browse CD and Exit.
If the opening screen does not appear; double-click the file setup.exe in the root directory.
Using the Motherboard Software
48
Drivers Tab Setup Click the Setup button to run the software installation program. Select from the menu which software you want to install.
Browse CD The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the contents of the support disk. Before installing the software from Windows Explorer, look for a file named README.TXT or something similar. This file may contain important information to help you install the software correctly. Some software is installed in separate folders for different operating systems. In installing the software, execute a file named SETUP.EXE by doubleclicking the file and then following the instructions on the screen.
Exit
The EXIT button closes the Auto Setup window.
Utilities Tab Lists the software utilities that are available on the disk. Information Tab Displays the path for all software and drivers available on the disk.
Running Setup
Follow these instructions to install device drivers and software for the motherboard:
1. Click Setup. The installation program begins:
The following screens are examples only. The screens and driver lists will be different according to the motherboard you are installing. The motherboard identification is located in the upper left-hand corner.
49
2. Click Next. The following screen appears:
3. Check the box next to the items you want to install. The default options are recommended. 4. Click Next run the Installation Wizard. An item installation screen appears:
5.
Follow the instructions on the screen to install the items.
Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the installation.
50
Windows Vista/7 will appear below UAC (User Account Control) message after the system restart. You must select Allow to install the next driver. Continue this process to complete the drivers installation.
Manual Installation
Insert the disk in the DVD-ROM/CD-ROM drive and locate the PATH.DOC file in the root directory. This file contains the information needed to locate the drivers for your motherboard. Look for the chipset and motherboard model; then browse to the directory and path to begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that automatically detects your operating system before installation. Other drivers have the setup program located in the operating system subfolder. If the driver you want to install does not have a setup program, browse to the operating system subfolder and locate the readme text file (README.TXT or README.DOC) for information on installing the driver or software for your operating system.
Utility Software Reference

All the utility software available from this page is Windows compliant. They are provided only for the convenience of the customer. The following software is furnished under license and may only be used or copied in accordance with the terms of the license. 1 . These software(s) are subject to change at anytime without prior no tice. Please refer to the support disk for available software. 2 . Please go to ECS website to download AMD Cool n QuietTM technology.
51
HDMI Audio setting SOP

OS: XP system
1. Control Panel-->Sound and Audio Device Properties
2. a. Audio--> Sound playback--> Default device--> HD Auido Output b. Audio--> Sound playback--> Default device--> HDMI Auido Output
3. a. User Playback Audio speaker function working b. User Playback HDMI speaker function working
52
OS: Vista system

Control Panel--> Soundback--> Sound--> Digital Output Device (HDMI) --> Set Default
1. Volume --> Playback
2. Digital Output Device (HDMI) --> Set Default --> OK User HDMI Playback function working
53
3. Speaker --> Set Default --> OK User Speaker Palyback function working
4. SPDIF-Out --> Set Default --> OK User SPDIF-Out Playback function working
This concludes chapter 4.
54
Memo
55
Chapter 5 Hybrid Graphics Technology Support Hybrid Graphics Technology

The Hybrid Graphics technology provides significant display performance boost to AMD-based systems by inserting the external PCI Express graphics card and enabling both the discrete GPU and the AMD785G graphics core to render simultaneously in Hybrid CrossFireTM mode. Follow the steps below to start the Hybrid Graphics technology. 1.Insert a graphics card (which can be used for Hybrid Graphics technology, such as HD3400 series) into the PCIEX16 slot. Make sure that the card is properly seated on the slot.
* For reference only 2. For Hybrid Graphics, if display by PCI-Express, you must enter the BIOS, set the Surround View in Advanced Chipset Setup to PCI Express. Then press F10 to save the configuration and exit the BIOS. After entering OS, enter Catalyst Control Center to enable Hybrid CrossFireTM.
Hybrid Graphics Technology Support
56
SurroundViewTM provides the power and convenience of multiadapter, multimonitor support for computers that use a PCI-Express based graphics card in conjunction with ATI integrated graphic processors. And there are two options: Disabled and PCI Express. If SurroundView TM set to Disabled , and Init Display First set to OnBoard, SurroundViewTM will be Enabled by Catalyst Control Center based on cancel the Enable CrossFireTM option. While if display by OnBoard, you must enter the BIOS, set the Init Display First in Advanced Chipset Setup to OnBoard. Then press F10 to save the configuration and exit the BIOS. After entering OS, enter Catalyst Control Center to enable CrossFireTM.
3. Click with your right mouse button on My Computer , then click the option Manage and choose the Device Manager, finally, click the Display Adapters. The following screen appears. Be sure that the external ATI graphics (ATI Radeon HD 3400 Grapics) and Onboard graphics (Radeon HD 4200) are both displaying in the Display adapters.
57
4. Enter Catalyst Control Center, you can see the option of CrossFireTM, click it and select Enable CrossFireTM, then Hybrid Graphics starts.
To disable Hybrid Graphics, please make sure to cancel Enable CrossFireTM in Catalyst Control Center firstly.
58
Memo
59
Chapter 6 Setting Up AMD SB710 RAID Configuration Setting Up a bootable RAID Array
This section explains how to configure a bootable AMD RAID array.
Setting Up the BIOS

1 Start your computer, then press Delete to enter the BIOS setup. The BIOS CMOS Setup Utility screen appears.
Figure 1.1
2
BIOS CMOS Setup Utility Main Screen
Use the arrow keys to select Integrated Peripherals (see Figure 1.1), then press Enter. The Integrated Peripherals screen (or a screen similar to it) appears.
Figure 1.2 3
Integrated Peripherals Screen
Use the arrow keys to select the SATA Configuration (see Figure 1.2) and globally set SATA Configuration to RAID.
AMD RAID Configuration
60
4 Press F10 to save the configuration and exit. The PC reboots. Enter the RAID BIOS Setup by pressing Ctrl-F when prompted, and proceed to set up the AMD RAID BIOS as described in the next section.
Configuring the AMD RAID BIOS

The AMD RAID BIOS set up lets you choose the RAID type and which hard drives you want to make part of the array.
Entering the RAID BIOS Setup:

1 Wait until you see the RAID software prompting you to press Ctrl-F. The RAID prompt appears as part of the system POST and boot process prior to loading of the OS. You have a few seconds to press Ctrl-F before the screen disappears. 2 Press Ctrl-F. The Main Menu screen appears (Figure 1.3).
Figure 1.3
Main Menu
61
3 Select [2], then select LD 1 in the following page. The Define LD Menu screen appears (Figure 1.4).
Figure 1.4
Define LD Menu
Using the Define a New Array Screen

If necessary, press the tab key to move from field to field until the appropriate field is highlighted. Selecting the RAID Mode By default, this is set to Mirroring. To change to a different RAID mode, press the spacebar until the mode that you want appears in the RAID Mode boxRAID0/1/10/JBOD. Note: Not all RAID levels are supported on all platforms.
Selecting the Stripe Block Size Stripe block size is given in kilobytes, and affects how data is arranged on the disk. It is recommended to leave this value at the default Optimal, which is 64KB, but the values can be 64 KB and 128 KB. When choose RAID 1, the Stripe block size is unchangable.
62
Assigning the Disks

1. Select the Assignment to Y to designate a free disk to be used as a RAID array disk. Figure 1.5 illustrates the Define a New Array screen after two disks have been assigned as RAID 0 array disks.
Figure 1.5
FastBuild UtilityArray Disks Assigned
2. Press Ctrl-Y to save the configuration and exit. The Define LD Menu screen appears (Figure 1.6).
Figure 1.6
Define LD Menu
63
3. Press ESC to exit. The Main Menu screen appears (Figure 1.7).
Figure 1.7
4 Press Y to reboot.
Main Menu
The following screen appears (Figure 1.8).
Figure 1.8
64
Installing the RAID Drivers

Your system may come with a Windows install CD that already includes AMD RAID drivers. If so, then this section is not relevant. If that is not the case (or you are trying to install a new version of Windows), then you will need an AMD RAID driver F6 install floppy. Check to see if one came with your system. If not, you can create one by downloading the appropriate driver package and following the steps in this section. 1 2 Copy all files in "...\RAID\ATI\SB750\Floppy\Win3264" to a floppy disk. After you complete the RAID BIOS setup, boot from the Windows CD. The Windows Setup program starts.
Figure 1.9 3 Press F6 and wait a few moments for the Windows Setup screen to appear.
Figure 1.10 4
Windows SetupSpecify Devices
Specify the AMD drivers. a Insert the floppy that has the RAID driver, press S, then press Enter.
65
The following Windows Setup screen appears:
Figure 1.11
Windows SetupSelected SCSI Adapter
b Select ATI AHCI Compatible RAID Controller-x86 platform and press Enter for 32-bit OS or Select ATI AHCI Compatible RAID Controller-x64 platform and press Enter for 64-bit OS. The following Windows Setup screen appears listing both drivers:.
Figure 1.12 Windows SetupAMD drives listed 5 Press Enter to continue with Windows XP Installation. Be sure to leave the floppy disk inserted in the floppy drive until the blue screen portion of Windows XP installation is completed, then take out the floppy. 6 Follow the instructions on how to install Windows XP. After Windows XP is completely installed, it is recommended that you install the ForceWare software in order to access the FastBuild RAID Management tool. Note: Each time you add a new hard drive to a RAID array, the RAID driver will have to be installed under Windows once for that hard drive. After that, the driver will not have to be installed.
66
Memo
67
Chapter 7 Setting Up eJIFFY Introduction

eJIFFY is a fast boot program under Linux. Instead of waiting Windows O.S to start execution, eJIFFY is ready to provide users the instant enjoyment on web browsing, photo review and online chat just within several seconds after boot up.
Note: eJIFFY is ECS optional feature utility corresponding to the DVD activation and BIOS setup. Please check the hard copy users guide or product color-box to see if the model has embodded eJIFFY feature. (eJIFFY icon on color-box )
Version: 4.0
Setting Up eJIFFY
68
Installation and BIOS Setup

DVD Activation
Finish the DVD utility setup, and then set the BIOS to complete eJIFFY activation. 1. Insert ECS software utility DVD and enter below Utilities screen. Click eJIFFY feature item to install.
2. Follow the onscreen instructions to finish eJIFFY setup.
Setting Up eJIFFY
69
3. After setting up eJIFFY under Windows, you can switch eJIFFY display/keyboard language from English to your local language. The changes will be applied after rebooting.
Note: The keyboard language selection list offers several more regional keyboard setups to switch with the default English typing. Please refer to the usage FAQ for more tips.
Setting Up eJIFFY
70
4. Restart your computer after eJIFFY installation. Press <DEL> or click the BIOS Setup button on the post screen to enter the BIOS setup page after boot up.
5. And then enter the Advanced Setup page to enable the item ECS eJIFFY Function. Press F10 to save the configuration and exit. Restart your computer.
Note: 1. eJIFFY is available in SATA/IDE/AHCI mode. It does not support RAID configuration and the onboard 34-pin floppy drives. 2. Please refer to ECS website for new eJIFFY application updates.
Setting Up eJIFFY
71
Entering eJIFFY
The post screen appears within several seconds after boot up and it has three buttons on it, Operating system, eJIFFY and BIOS Setup.
Click to enter the normal OS you have installed such as Windows. Click to enter eJIFFY OS.
Click to set the BIOS.
If you click eJIFFY, the following screen will appear. And If you make no choice it will enter the normal OS automatically after ten seconds.
Setting Up eJIFFY
72
Feature Icons
The following illustration shows the main feature icons that eJIFFY provides on the menu.
eWeb: Firefox for web browsing/webmail and watching flash video.
ePix: Photo viewing.
ePal: On-line chat tool to use the most popular IMs in the world. (MSN, ICQ , AIM, etc.)
Shows ePal on-line connection status.
Shut Down/Restart: Ends your session and turns off the computer./Ends your session and restart the computer.. Click once to connect the storage disk to your computer. Click for the second time to remove your storage disk safely. (please refer to the FAQ for more usage information.)
Shows the network connection status.
Language Control Panel
Switch Keyboard Languages
Setting Up eJIFFY
73
Usage FAQ
Language Control Panel: Besides setting English as the default interface, eJIFFY offers multi-language displays and keyboard settings for languageswitch. Open the language control panel to select a preferable language setting.
Keyboard Language Setup

Step1. Click to open the language control panel.
Setting Up eJIFFY
74
Step 2: Click Keyboard Language icon
to open the keyboard selection
list, which offers several regional keyboard settings besides default English keyboard.
Step 3: Click the selected keyboard language (e.g. French) and press OK.
Setting Up eJIFFY
75
Tips for Language Switch:

Tip 1: Click Change Keyboard icon to switch the typing language.
The typing language on text box will switch to the selected one:
Click
again to switch to English typing back.
Tip 2. If you use the default English keyboard, eJIFFY still offers other language inputs to switch with English.
Click Apply:
to enable all possible language inputs you want to apply, and click
Setting Up eJIFFY
76
Setting Up eJIFFY
77
Setting Up eJIFFY
78
Tip 3. How to change display language? Open the Language Control Panel and click to show the display language
list. Check your desired display language. Your selected display language will be applied after rebooting.
Setting Up eJIFFY
79
eWeb: Firefox for web browsing/webmail and watching flash video.
Q1: How to download files to hard disk through eWeb? Click on the file link directly. Then select Save File in the pop-up window.
Note: 1. Before downloading files, please mount the storage devices to make sure the device is connected with eJIFFY interface. (Please refer to the usage FAQ to mount devices) 2. eWeb does not support Office Viewer/Reader/Writer format under eJIFFY interface. Please enter the Operating System to open Office files. 3. eWeb supports to open video/audio files online in Flash player format. Due to firefox limitation, the browser does not support files in Real player or Media player formats.
Setting Up eJIFFY
80
Q2: How to save image file through eWeb? 1. Select the image you want to save and press the right key of your mouse to show the menu, then click the option Save Image As from the menu.
2. Then the Save Image window appears. You may rename the image file in the Name column and save the file in a folder as the following picture shows.
Rename the image file.
Select a root directory.
Then select a subdirectory or click Create Folder to create a new folder.
Click here to save the image file.
Setting Up eJIFFY
81
ePix: Photo viewing.
Q1: How to find image files saved in hard disk through ePix?
Enter the ePix window, then click the icon Folder located in the upper left-hand corner, then follow the path for the files you have saved to view the image files.
Setting Up eJIFFY
82
Q2: How to use the fit function under slide show? 1. Click Edit and select Preferences option from the menu.
2. Click Viewer and choose Keep previous zoom in After loading an image. Close the window and you can use the fit function under slide show now.
Note: ePix supports to view image files only. It cannot support Office Viewer or other forms beside image files. Supported image types are: BMP, JPEG, GIF (including GIF animations), PNG, TIFF, ICO and XPM.
Setting Up eJIFFY
83
Mount/Unmount Disk.
Q1: What does it mean for Mount Disk? Mount means to connect the storage devices to eJIFFY interface. After plugging the external device to the computer such as USB drives, a new disk icon will appear as the following picture shows. Please click the mount prompt on the icon. It will change to to show the device is detected successfully.
Q2: What does it mean for Unmount Disk? Unmount is to safely remove the storage devices. To unplug the external storage devices such as USB drives, users need to clik the Unmount prompt as the following picture shows, then the icon will change to , you can remove the device now.
Setting Up eJIFFY
84
Memo
Setting Up eJIFFY
85
Chapter 8 Trouble Shooting Start up problems during assembly

After assembling the PC for the first time you may experience some start up problems. Before calling for technical support or returning for warranty, this chapter may help to address some of the common questions using some basic troubleshooting tips.
a) System does not power up and the fans are not running.
1.Disassemble the PC to remove the VGA adaptor card, DDR memory, LAN, USB and other peripherals including keyboard and mouse. Leave only the motherboard, CPU with CPU cooler and power supply connected. Turn on again to see if the CPU and power supply fans are running. 2. Make sure to remove any unused screws or other metal objects such as screwdrivers from the inside PC case. This is to prevent damage from short circuit. 3. Check the CPU FAN connector is connected to the motherboard. 4. For Intel platforms check the pins on the CPU socket for damage or bent. A bent pin may cause failure to boot and sometimes permanent damage from short circuit. 5. Check the 12V power connector is connected to the motherboard. 6. Check that the 12V power & ATX connectors are fully inserted into the motherboard connectors. Make sure the latches of the cable and connector are locked into place.
b) Power is on, fans are running but there is no display

1. Make sure the monitor is turned on and the monitor cable is properly connected to the PC. 2. Check the VGA adapter card (if applicable) is inserted properly. 3. Listen for beep sounds. If you are using internal PC speaker make sure it is connected. a. continuous 3 short beeps : memory not detected b. 1 long beep and 8 short beeps : VGA not detected
Trouble Shooting
86
c) The PC suddenly shuts down while booting up.

1. The CPU may experience overheating so it will shutdown to protect itself. Ensure the CPU fan is working properly. 2. From the BIOS setting, try to disable the Smartfan function to let the fan run at default speed. Doing a Load Optimised Default will also disable the Smartfan.
Start up problems after prolong use

After a prolong period of use your PC may experience start up problems again. This may be caused by breakdown of devices connected to the motherboard such as HDD, CPU fan, etc. The following tips may help to revive the PC or identify the cause of failure. 1. Clear the CMOS values using the CLR_CMOS jumper. Refer to CLR_CMOS jumper in Chapter 2 for Checking Jumper Settings in this user manual. When completed, follow up with a Load Optimised Default in the BIOS setup. 2. Check the CPU cooler fan for dust. Long term accumulation of dust will reduce its effectiveness to cool the processor. Clean the cooler or replace a new one if necessary. 3. Check that the 12V power & ATX connectors are fully inserted into the motherboard connectors. Make sure the latches of the cable and connector are locked into place. 4. Remove the hard drive, optical drive or DDR memory to determine which of these component may be at fault.
Maintenance and care tips

Your computer, like any electrical appliance, requires proper care and maintenance. Here are some basic PC care tips to help prolong the life of the motherboard and keep it running as best as it can. 1. Keep your computer in a well ventilated area. Leave some space between the PC and the wall for sufficient airflow. 2. Keep your computer in a cool dry place. Avoid dusty areas, direct sunlight and areas of high moisture content. 3. Routinely clean the CPU cooler fan to remove dust and hair. 4. In places of hot and humid weather you should turn on your computer once every other week to circulate the air and prevent damage from humidity. 5. Add more memory to your computer if possible. This not only speeds up the system but also reduces the loading of your hard drive to prolong its life span. 6. If possible, ensure the power cord has an earth ground pin directly from the wall outlet. This will reduce voltage fluctuation that may damage sensitive devices.
Trouble Shooting
Basic Troubleshooting Flowchart
Power Bu on is pressed but PC fails to start.
Check if Power Supply Unit (PSU) is working
No
AC power cord is plugged and PSU switch is turned on?
No
Yes
Any Beep sound is connected
No
if CPU 12V power
No
CLR CMOS and check
Yes
Problem with PSU or board? If board problem -> contact RMA
Check if monitor has display
Yes Yes
- If 3 short beeps: DIMM memory not properly inserted or memory failure - If 1 long beep and 8 short beeps: VGA not detected Check if monitor has display Restart the PC
Halt at POST screen
No
Turn on PSU switch or connect to wall socket and restart.
Yes
No
CLR CMOS and restart.
Board problem -> contact RMA
If fail, contact RMA
Yes
Peripheral device issue
HDD problem. System fail to start or unstable a er modify BIOS se ng. CLR CMOS and restart
CMOS setup error,
need to CLRCMOS.
87
88
Memo
Trouble Shooting

A785GM-A Manual2

Uploaded by

Copyright:

Available Formats

A785GM-A Manual2

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

A785GM-A Manual2

Uploaded by

Copyright:

Available Formats

Preface

Federal Communications Commission (FCC)

Canadian Department of Communications

About the Manual

Describes features of the motherboard. page 1 Go to

Describes installation of motherboard components. page 7 Go to

Provides information on using the BIOS Setup Utility. Go to page 27

Describes the motherboard software Go to

Describes the Hybrid Graphics Technology Go to

Describes the AMD SB710 RAID Configuration Go to

Describes the eJIFFY setting up Go to page 67

Provides basic trouble shooting tips Go to page 85

Connecting I/O Devices......................................................................22 Connecting Case Components..........................................................23

Using BIOS 27 About the Setup Utility....................................................................27

Manual Installation..........................................................................50 Utility Software Reference................................................................50

Hybrid Graphics Technology Support 55 Hybrid Graphics Technology.........................................................55

Setting Up AMD SB710 RAID Configuration 59 Setting Up a Bootable RAID Array...................................................59

Chapter 1 Introducing the Motherboard Introduction

Introducing the Motherboard

Introducing the Motherboard

Introducing the Motherboard

Introducing the Motherboard

Table of Motherboard Components

Introducing the Motherboard

Introducing the Motherboard

Chapter 2 Installing the Motherboard Safety Precautions

Choosing a Computer Case

Installing the Motherboard in a Case

Installing the Motherboard

Do not over-tighten the screws as this can stress the motherboard.

Checking Jumper Settings

Installing the Motherboard

Checking Jumper Settings

USB Power Cotroller

USB Power Cotroller

1-2: VCC5 2-3: 5VSB

USB Power Cotroller

1-2: VCC5 2-3: 5VSB

Installing the Motherboard

Before installing the Processor

Installing the Motherboard

CPU Installation Procedure

Installing Memory Modules

DDR2 SDRAM memory module table

DDR2 DDR2 DDR2 DDR2 DDR2

400 533 667 800 1066

200 266 333 400 533

MHz MHz MHz MHz MHz

Installing the Motherboard

Recommend configuration for best performance and compatibility

AM2+ * Unganged Mode Ganged Mode Unganged Mode Ganged Mode

: operation with normal performance : operation with the best performance

Installing the Motherboard

Table A: DDR2 (memory module) QVL (Qualified Vendor List)

1GB DDR2 667

Apacer CORSAIR Geil Hynix KingMax

Kingston Micron Nanya PSC Samsung Unifosa

Samsung Micron Micron

Installing the Motherboard

Installing the Motherboard