Sigma Vikote 56

page 1/3
J uly 2009 3 pages

Revision of September 2005
modied acrylic nish
nish coat for above water areas
good gloss and colour retention
resistant to water and splash of mild chemicals
fast drying
can be applied at low temperatures, down to -10C
white and various other colours (see also the SigmaCare Shade Card of PPG
Protective & Marine Coatings) - gloss
(1 g/cm =8.25 lb/US gal; 1 m/l =40.7 ft/US gal)
1.1 g/cm
35 2%
max. 538 g/kg (Directive 1999/13/EC, SED)
max. 569 g/l (approx. 4.7 lb/gal)
35 m
10 m/l for 35 m
1 hour at 5C, 30 min. at 20C
min. 8 hours at 5C, 4 hours at 20C
max. unlimited
at least 24 months
previous coat; chlorinated rubber, vinyl or acrylic coatings, dry and free from
any contamination
substrate temperature should be at least 3C above dew point
marine system sheets: 3102, 3103, 3104
stir well before use
the temperature of the paint should preferably be above 15C, otherwise
extra thinner may be required to obtain application viscosity
too much solvent results in reduced sag resistance
adequate ventilation must be maintained during application and curing
(please refer to sheets 1433 and 1434)

Thinner 21-06
5 - 10%, depending on required thickness and application conditions
approx. 0.28 - 0.33 mm (=0.011 - 0.013 in)
12 - 15 MPa (=approx. 120 - 150 bar; 1700 - 2130 p.s.i.)
DESCRIPTION
PRINCIPAL CHARACTERISTICS
COLOURS AND GLOSS
BASIC DATA AT 20C
Mass density
Volume solids
VOC (supplied)

Recommended dry lm thickness
Theoretical spreading rate
Touch dry after
Overcoating interval
Shelf life (cool and dry place)
RECOMMENDED
SUBSTRATE CONDITIONS
AND TEMPERATURES
SYSTEM SPECIFICATION
INSTRUCTIONS FOR USE
AIRLESS SPRAY
Recommended thinner
Volume of thinner
Nozzle orice
Nozzle pressure
SIGMA VIKOTE 56
page 2/3
J uly 2009
SIGMA VIKOTE 56

Thinner 21-06
0 - 5%, depending on required thickness and application conditions
1.8 - 2 mm
0.2 - 0.3 MPa (=approx. 2 - 3 bar; 28 - 43 p.s.i.)

Thinner 21-06
0 - 3%
Thinner 21-06
for paint and recommended thinners see safety sheets 1430, 1431 and relevant
material safety data sheets
this is a solvent borne paint and care should be taken to avoid inhalation of
spray mist or vapour as well as contact between the wet paint and exposed skin
or eyes
Colour scheme:
Sigma Vikote 56 colours to be applied on top of Sigma Vikote 46 colours
Sigma Vikote 56 colours Sigma Vikote 46 colours
7003, 7000, 1188, 3138, 3142 Offwhite
3179, 3149, 4150, 4171, 5163 Offwhite
1188, 1199, 5163, 5177, 6188 Light grey
5177, 5198, 8000 Dark grey
4199 Green
2182, 6179 Redbrown
8000 Black
Whilst it is always the aim of PPG Protective & Marine Coatings to supply
the same product on a worldwide basis, slight modication of the product is
sometimes necessary to comply with local or national rules/circumstances.
Under these circumstances an alternative product data sheet is used.
Explanation to product data sheets see information sheet 1411
Safety indications see information sheet 1430
Safety in conned spaces and health safety
Explosion hazard - toxic hazard see information sheet 1431
Safe working in conned spaces see information sheet 1433
Directives for ventilation practice see information sheet 1434
AIR SPRAY
Recommended thinner
Volume of thinner
Nozzle orice
Nozzle pressure
BRUSH/ROLLER
Recommended thinner
Volume of thinner
CLEANING SOLVENT
SAFETY PRECAUTIONS
ADDITIONAL DATA
Worldwide availability
REFERENCES
page 3/3
J uly 2009
SIGMA VIKOTE 56
LIMITATION OF LIABILITY
The information in this data sheet is based upon laboratory tests we believe to be accurate and is intended for
guidance only. All recommendations or suggestions relating to the use of the Sigma Coatings products made by PPG
Protective & Marine Coatings, whether in technical documentation, or in response to a specic enquiry, or otherwise,
are based on data which to the best of our knowledge are reliable. The products and information are designed for
users having the requisite knowledge and industrial skills and it is the end-user's responsibility to determine the
suitability of the product for its intended use.
PPG Protective & Marine Coatings has no control over either the quality or condition of the substrate, or the many
factors affecting the use and application of the product. PPG Protective & Marine Coatings does therefore not accept
any liability arising from loss, injury or damage resulting from such use or the contents of this data sheet (unless there
are written agreements stating otherwise).
The data contained herein are liable to modication as a result of practical experience and continuous product
development.
This data sheet replaces and annuls all previous issues and it is therefore the user's responsibility to ensure that this
sheet is current prior to using the product.
The English text of this document shall prevail over any translation thereof.
PDS 7355
154022 white 7000002200

Sigma Vikote 56

Uploaded by

Copyright:

Available Formats

Sigma Vikote 56

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sigma Vikote 56

Uploaded by

Copyright:

Available Formats

page 1/3

J uly 2009 3 pages

You might also like