Series: Inductors For Standard Circuits

I N D U C T O R S
NL453232 4532 [1812 inch]*

NL565050 5650 [2220 inch]
* Dimensions Code JIS[EIA]
May 2013
Inductors for Standard Circuits
Wound Ferrite
NL series
(1/12)
I N D U C T O R S
001-01 / 20130516 / e511_nl.fm
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 40C, Humidity: 10 to 75% RH or
less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
REMINDERS
(2/12)
I N D U C T O R S
001-01 / 20130516 / e511_nl.fm
All specifications are subject to change without notice.
Inductors for Standard Circuits
Wound Ferrite
FEATURES
Resin mold type wound inductor for standard circuits.
1 to 10000H, E-12 Series, wide lineup compatible with J (5%) tolerance, can be used for applications that need to meet strict L
tolerance such as filter circuits.
Has excellent inductance temperature characteristics in the operating temperature range.
APPLICATION
Smart meters, AV equipment, xDSL, electronic devices for communications infrastructure such as mobile base stations, industrial
equipment, other
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT

Operating temperature range includes self-temperature rise.

The Storage temperature range is for after the circuit board is mounted.
Product compatible with RoHS directive
Compatible with lead-free solders
Overview of the NL Series
NL 453232 T - 1R0 J - PF
Series name
LWH Dimensions
Packaging style
Inductance Inductance
tolerance
Internal code
(mm) (H)
453232 4.53.23.2 T Taping 1R0 1 J 5%
565050 5.65.05.0 100 10
101 100
102 1000
103 10000
Type
Temperature range
Package quantity Individual weight Operating
temperature
Storage
temperature
C C
(pieces/reel)
mg
NL453232 40 to +105 40 to +105 500 180
NL565050 40 to +105 40 to +105 400 380
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
(3/12)
I N D U C T O R S
001-01 / 20130516 / e511_nl.fm
Overview of the NL Series
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150C 180C 90 to 120s 230C 40s 255C 10s max.
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T
:

T
e
m
p
e
r
a
t
u
r
e
(4/12)
I N D U C T O R S
001-01 / 20130516 / e511_nl.fm
NL series
NL453232 Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
R0.2
C0.5
102J
4.50.3
3
.
2
0
.
2
3
.
2
0
.
2
2
.
6
0
.
1
0.5 (3.3) (0.6) (0.6)
Dimensions in mm
2
.
8
1.5 3 1.5
(5/12)
I N D U C T O R S
001-01 / 20130516 / e511_nl.fm
NL series NL453232 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE

Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (10% below the initial value)
Idc2: When based on the temperature increase (Temperature increase of 20C by self heating)
Measurement equipment
Equivalent measurement equipment may be used.
L
Q
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(MHz)
min.
DC resistance
()
max.
Rated current
(mA)
max.
Part No.
(H) Tolerance
1 5% 50 7.96 100 0.5 450 NL453232T-1R0J-PF
1.2 5% 50 7.96 80 0.55 430 NL453232T-1R2J-PF
1.5 5% 50 7.96 70 0.6 410 NL453232T-1R5J-PF
1.8 5% 50 7.96 60 0.65 390 NL453232T-1R8J-PF
2.2 5% 50 7.96 55 0.7 380 NL453232T-2R2J-PF
2.7 5% 50 7.96 50 0.75 370 NL453232T-2R7J-PF
3.3 5% 50 7.96 45 0.8 355 NL453232T-3R3J-PF
3.9 5% 50 7.96 40 0.9 330 NL453232T-3R9J-PF
4.7 5% 50 7.96 35 1 315 NL453232T-4R7J-PF
5.6 5% 50 7.96 33 1.1 300 NL453232T-5R6J-PF
6.8 5% 50 7.96 27 1.2 285 NL453232T-6R8J-PF
8.2 5% 50 7.96 25 1.4 270 NL453232T-8R2J-PF
10 5% 50 2.52 20 1.6 250 NL453232T-100J-PF
12 5% 50 2.52 18 2 225 NL453232T-120J-PF
15 5% 50 2.52 17 2.5 200 NL453232T-150J-PF
18 5% 50 2.52 15 2.8 190 NL453232T-180J-PF
22 5% 50 2.52 13 3.2 180 NL453232T-220J-PF
27 5% 50 2.52 12 3.6 170 NL453232T-270J-PF
33 5% 50 2.52 11 4 160 NL453232T-330J-PF
39 5% 50 2.52 10 4.5 150 NL453232T-390J-PF
47 5% 50 2.52 10 5 140 NL453232T-470J-PF
56 5% 50 2.52 9 5.5 135 NL453232T-560J-PF
68 5% 50 2.52 9 6 130 NL453232T-680J-PF
82 5% 50 2.52 8 7 120 NL453232T-820J-PF
100 5% 40 0.796 8 8 110 NL453232T-101J-PF
120 5% 40 0.796 6 8 110 NL453232T-121J-PF
150 5% 40 0.796 5 9 105 NL453232T-151J-PF
180 5% 40 0.796 5 9.5 102 NL453232T-181J-PF
220 5% 40 0.796 4 10 100 NL453232T-221J-PF
270 5% 40 0.796 4 12 92 NL453232T-271J-PF
330 5% 40 0.796 3.5 14 85 NL453232T-331J-PF
390 5% 40 0.796 3 16 80 NL453232T-391J-PF
470 5% 40 0.796 3 26 62 NL453232T-471J-PF
560 5% 30 0.796 3 30 50 NL453232T-561J-PF
680 5% 30 0.796 3 30 50 NL453232T-681J-PF
820 5% 30 0.796 2.5 35 30 NL453232T-821J-PF
1000 5% 30 0.252 2.5 40 30 NL453232T-102J-PF
Measurement item Product No. Manufacturer
L, Q 4194A Agilent Technologies
Self-resonant frequency 8753C Agilent Technologies
DC resistance VP-2941A Panasonic
(6/12)
I N D U C T O R S
001-01 / 20130516 / e511_nl.fm
L FREQUENCY CHARACTERISTICS GRAPH
0.001 0.01 0.1 10 1 100
0.1
100000
100
1000
10000
1
10
I
n
d
u
c
t
a
n
c
e
(
H
)

Frequency(MHz)
102J
821J
681J
561J
391J
221J
181J
471J
331J
271J
151J
820J
680J
390J
270J
101J
121J
560J
470J
330J
220J
120J
100J
6R8J
5R6J
4R7J
3R9J
180J
150J
3R3J
2R7J
2R2J
1R8J
1R5J
1R2J
1R0J
8R2J
Product No. Manufacturer
4294A Agilent Technologies
(7/12)
I N D U C T O R S
001-01 / 20130516 / e511_nl.fm
Q FREQUENCY CHARACTERISTICS GRAPH
0
10
20
30
40
50
60
Q
70
80
90
100
0.001 0.01 0.1 10 1 100
Frequency(MHz)
271J
821J
102J
331J
681J
391J
561J
471J
151J
121J
101J
820J
470J
330J
270J
560J
680J
220J
3R9J
5R6J
4R7J
6R8J
8R2J
100J
120J
150J
180J
1R0J
3R3J
2R7J
1R2J
2R2J
1R8J
1R5J
181J
390J
221J
(8/12)
I N D U C T O R S
001-01 / 20130516 / e511_nl.fm
NL series
NL565050 Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
472J
5.60.3
5
0
.
3
5
0
.
3
C1
4
0
.
2
1 (4.6) (0.5) (0.5)
472J
Dimensions in mm
4
.
5
2 4 2
(9/12)
I N D U C T O R S
001-01 / 20130516 / e511_nl.fm
CHARACTERISTICS SPECIFICATION TABLE

Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (10% below the initial value)
Idc2: When based on the temperature increase (Temperature increase of 20C by self heating)
L
Q
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(MHz)
min.
DC resistance
()
max.
Rated current
(mA)
max.
Part No.
(mH) tolerance
1.2 5% 30 0.252 1.5 17 75 NL565050T-122J-PF
1.5 5% 30 0.252 1.4 20 70 NL565050T-152J-PF
1.8 5% 30 0.252 1.3 30 60 NL565050T-182J-PF
2.2 5% 30 0.252 1.2 35 55 NL565050T-222J-PF
2.7 5% 30 0.252 1.1 55 45 NL565050T-272J-PF
3.3 5% 30 0.252 1 60 40 NL565050T-332J-PF
3.9 5% 30 0.252 1 70 38 NL565050T-392J-PF
4.7 5% 30 0.252 0.9 78 36 NL565050T-472J-PF
5.6 5% 30 0.252 0.8 85 33 NL565050T-562J-PF
6.8 5% 30 0.252 0.7 110 30 NL565050T-682J-PF
8.2 5% 30 0.252 0.6 125 28 NL565050T-822J-PF
10 5% 20 0.0796 0.5 150 25 NL565050T-103J-PF
Measurement item Product No. Manufacturer
L, Q 4194A Agilent Technologies
Self-resonant frequency 8753C Agilent Technologies
DC resistance VP-2941A Panasonic
(10/12)
I N D U C T O R S
001-01 / 20130516 / e511_nl.fm
NL series NL565050Type
L FREQUENCY CHARACTERISTICS GRAPH
0.001 0.01 0.1 1 10
1
100000
100
1000
10000
100000
10
Frequency(MHz)
I
n
d
u
c
t
a
n
c
e
(
H
)

103J
472J
682J
562J
332J
272J
222J
182J
152J
122J
822J
392J
(11/12)
I N D U C T O R S
001-01 / 20130516 / e511_nl.fm
Q FREQUENCY CHARACTERISTICS GRAPH
0
10
20
30
40
50
60
Q
0.001 0.01 0.1 1 10
Frequency(MHz)
103J
562J
822J
682J
472J
332J
122J
222J
182J
152J
272J
392J
(12/12)
I N D U C T O R S
001-01 / 20130516 / e511_nl.fm
NL series
Packaging Style
REEL DIMENSIONS
* These values are typical values.
TAPE DIMENSIONS
Type A B C D E
NL453232 180 17 60 13 0.5
NL565050 180 17 60 13 0.5
E 13.00.5
21.00.8
C
B 2.00.5
A
Dimensions in mm
(1.0)
D
F
E
W
P0 P2 D0 P1
A0
t
B
0
K
Dimensions in mm
Type A0 B0 D0 E F P0 P1 P2 W K t
NL453232 3.6 4.9 1.5+0.1/-0 1.750.1 5.500.05 4.000.10 8.000.10 2.000.05 12.00.30 3.2 0.4
NL565050 5.4 5.8 1.5+0.1/-0 1.750.1 5.500.05 4.000.10 8.000.10 2.000.05 12.00.30 5.4 0.4

Series: Inductors For Standard Circuits

Uploaded by

Copyright:

Available Formats

Series: Inductors For Standard Circuits

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Series: Inductors For Standard Circuits

Uploaded by

Copyright:

Available Formats

I N D U C T O R S

NL453232 4532 [1812 inch]*

You might also like