Troubleshooting ST Path Damage Mechanisms

Thomas H.
(Tom) McCloskey, formerly

Manager of Turbomachinery at EPRI, is
now Senior Turbomachinery Consulting
Engineer at APTECH Engineering Services,
Inc., in Sunnyvale, California. Throughout
his 32-year career, he has been responsible
for the design, operation, maintenance, and
troubleshooting of both fossil and nuclear
steam turbines up to 1300 MW in size. Mr.
McCloskey holds seven patents in steam
turbine design and is a Fellow Member of
the American Society of Mechanical Engineers (ASME). He
received the ASME George Westinghouse Gold Medal in 1995 and
the Edison Electric Institute Prime Movers Award in 1984 and
1997.
ABSTRACT
Steam path damage, particularly of rotating and stationary
blading, has long been recognized as a leading cause of steam
turbine unavailability for large fossil fuel plants worldwide.
Turbine problems cost the utility industry as much as one billion
dollars per year. Failures of blades, discs, and rotors in both fossil
and nuclear steam turbines represent a serious economic loss of
availability and reliability for electric power generation suppliers
and other energy supplies worldwide. Turbine problems such as
deposition and erosion of blades can result in severe efficiency
losses, resulting in significant economic penalties. The primary
objective of this tutorial is to provide a methodology to identify the
underlying damage or failure mechanisms, determine the root
cause, and choose immediate and long-term actions to lessen or
prevent recurrence of the problem.
INTRODUCTION AND BACKGROUND
Failures of blades, discs, and rotors in both fossil and nuclear
steam turbines represent a serious loss of availability and
reliabilitywith significant economic consequencesfor steam
turbine operators worldwide. Preventing these failures from
occurring requires strict adherence to three philosophical beliefs
(McCloskey, et al., 1999):
Understanding the mechanism and root cause of each incident is

of paramount importance to permanent alleviation of the problem.
By understanding what causes a problem to occur, it should be

possible to anticipate its development, monitor evolving
precursors, and take early action to avoid a significant condition
from occurring.
A formalized companywide program for correction, prevention,

and control can minimize steam path problems in the turbine.
Events can emanate from inadequate initial design, poor operation
and maintenance, cycle chemistry environments, or lack of proper
management support.
Figures 1 and 2 depict some very early turbine steam path failures
showing rotating blade erosion and axial disc fatigue (Stodola,
1905; Campbell, 1924).
Figure 1. Double Sided Rotating Blade Erosion from Exfoliated
Boiler Oxides. (Courtesy Stodola, 1905)
Figure 2. High Cycle Fatigue in Turbine Discs from Axial
Blade/Disc Resonances. (Courtesy Campbell, 1924)
FORMALIZING A COMPANYWIDE PROGRAM
FOR CORRECTION, PREVENTION, AND
CONTROL OF STEAM PATH DAMAGE
This tutorial focuses on technical guidance to understand,
prevent, and correct turbine steam path damage. However, it is
clear from previous experience that more than just access to proper
technical guidance will be necessary to reduce the costs associated
with turbine damage. Organizations with formalized,
companywide programs and a commitment to reducing turbine
steam path damage will be the ones that garner the most significant
benefits from the technical experience base.
105
TROUBLESHOOTING TURBINE STEAM PATH DAMAGE MECHANISMS
by
Thomas H. McCloskey
Senior Turbomachinery Consulting Engineer
APTECH Engineering Services, Inc.
Sunnyvale, California
Aspects of successful programs include:
Emphasis on the importance of a corporate directive reflecting

continued management support for steam path damage reduction
activities (as part of ensuring the continued performance of the
turbines).
Emphasis on training and commitment of personnel. It is not

possible to overemphasize the importance of operator and
maintenance personnel training, experience, and commitment to
the health of the unit.
An emphasis on the importance of a multifunctional team, i.e.,

steam path failures are not just a maintenance problem, but should
involve operators, chemists, and other functional groups.
A recognition that the long-term view of damage prevention is

not only cost effective, but a requirement to enable extended
turbine outage intervals.
Training of key personnel (operators, chemists, maintenance

personnel, and management) is central to the success of the
program and is a continual process with the addition of new
program personnel and/or management. The maximum time
between training sessions should be limited to two years.
The necessary technical understanding and the solutions needed

to mitigate outbreaks of steam path damage are known and are
available; it is important to make sure that the information is
systematically applied to outbreaks of turbine damage and to
prevention of damage.
A commitment to determining the correct underlying cause of

damage. Much of the time damage is wrongly characterized,
making it impossible to prescribe the appropriate action and avoid
a repeat of the same damage in the future. In many cases, the final
failure is remote enough from the causing event or series of
causing events that the true cause is obscured.
Remaining life assessment for damage components is a critical

part of the successful turbine program. Such assessments,
combined with risk analysis, are particularly critical for units
moving to longer outage intervals.
A detailed nondestructive evaluation (NDE) inspection of a

turbine by trained staff is essential to detect developing or
emerging problems such as corrosion fatigue, stress corrosion
cracking, creep, high cycle fatigue, and low cycle fatigue in known
susceptible areas such as rotors and blades.
Established shutdown procedures such as to provide a dehumid-

ified atmosphere to the steam-touched components.
Three key parts of a formal program are:
A formal corporate directive or a philosophy statement to

provide action oriented directives and procedures.
Forming a multidisciplinary team. The turbine condition

assessment team (T-CAT) to take responsibility for all actions
required to ensure the continued reliable and safe operation of the
turbine including preventing steam path damage.
The comprehensive reporting and trending of steam path

condition. There clearly needs to be a responsible and accountable
person in each power plant whose specific task is to coordinate all
turbine steam path condition investigations.
Figure 3 details these three key aspects of the corporate program
along with the activities of the T-CAT.
Other success factors for the formalized program that are
addressed throughout this tutorial include:
Attention to indicators that damage is accumulating,
Evaluation of unit precursors to turbine damage,
Optimizing inspection and outage intervals,
Identifying the appropriate root cause of damage,
Determining the residual life of damaged turbine components,
Applying permanent engineering solutions to problems

identified,
Maintaining established procedures and careful control over

startup, shutdown, and layup conditions in the turbine.
Figure 3. Steam Turbine Root Failure Cause Analysis Flowchart.
Once established, the T-CAT and the formal program will have
representatives from, and continued interfaces with, plant
operating, maintenance, chemistry, and engineering personnel. For
example, cycle chemistry can have a significant impact on steam
path damage. Therefore, there is a need to allow operating
personnel to direct unit activities so as to set and achieve cycle
chemistry goals and thus protect the turbine. Actions might
include: application of permanent engineering solutions,
development of controllable procedures, and the use of instru-
mentation to monitor critical control parameters. Interaction
between the T-CAT and other such plant decisions will be critical.
A useful classification for influences on steam path damage is:
Operation-controllable,
Maintenance-controllable,
Chemistry-controllable,
Management-controllable,
Design-related,
Manufacture-related, and
Installation-related.
The last three of these are termed -related as the owner/operator
will have little control over them once the installation has been
completed, the exception being when replacements or upgrades are
contemplated. In contrast, the first four factors are controllable by
the organization. The key recognition provided in such a schema is
that specific activities, choices, and controls within the job function
of a variety of personnel will affect the occurrence of turbine steam
PROCEEDINGS OF THE THIRTY-FIRST TURBOMACHINERY SYMPOSIUM 2002 106
path damage. Training and clear directive is critical for each group
to have an appropriate role in preventing turbine damage. Without
specific directives, it can be very difficult for operating personnel
to convince system control personnel that significant conditions in
the unit are harmful to the turbine.
CORPORATE DIRECTIVES/PHILOSOPHY
STATEMENT AND PROGRAM GOALS
The most important step in implementing an effective turbine
steam path damage reduction program is to develop and issue a
corporate philosophy statement signed by senior management. The
statement provides corporate direction and support for all
functional groups within the organization to engage in activities
specifically targeted to ensuring the continued safe and reliable
operation of the turbine, including reducing turbine damage and
associated costs.
The philosophy statement should be built from short- and long-
term goals, and must also provide direction for the necessary
corrective and preventive actions necessary to reduce damage
accumulation.
THE TURBINE CONDITION ASSESSMENT
TEAMMULTIDISCIPLINARY APPROACH
AND PERSONNEL TRAINING
A turbine condition assessment team consisting of representa-
tives of all pertinent functional groups (maintenance, engineering,
operations, chemistry, and management) should be set up. It is
important that all functional groups are represented as this
increases the likelihood that each will then understand the implica-
tions of their actions on the performance of the turbine and in
meeting the overall goals established in the philosophy statement.
The T-CAT will have multiple functions, and between outages
the T-CAT should:
Monitor turbine performance. This may include all existing

instrumentation and monitoring systems, the installation of new
systems such as through access ports, periodic checks of efficiency,
etc.
Determine whether specific damage indicators are starting to

appear.
Determine whether precursors to turbine damage are occurring

in the unit. These precursors might include such conditions as
steam chemistry upsets, operational upsets, problems with other
equipment, etc.
If conditions arise that require turbine work, the T-CAT should

recommend whether:
The unit condition is acceptable to run until the next
assessment,
The unit requires work to be performed at the next weekend
shutdown,
The unit requires work at the next unit boiler outage.
Anticipate and be able to respond quickly to any turbine

incidents.
Establish the optimal interval between turbine outages (refer to

discussion below) and to review each step in the planned outage to
minimize the length of outage required.
Anticipate and be able to respond to any damage found during

planned turbine outages. This may include such anticipatory steps
as:
Building preprepared finite element models,
Accumulation of databases of materials properties,
Comparison of prior inspection records so changes in
component condition can be easily made (APPENDIX A Figures
A-1, A-2, A-3).
Assuming qualified repair procedures are in hand,
Advanced analysis to determine which run/repair/replace
choice will be used depending on the damage found once the
turbine is opened.
Review spares policy and establish the optimum inventory.
Determine what ramifications to other parts of the unit may be

implied by an incident of damage.
COMPREHENSIVE REPORTING AND TRENDING
Standardized report forms, such as shown in APPENDIX A
Figures A-1, A-2, A-3, for blading along with a means to store,
evaluate, and disseminate information about turbine condition/
damage are required. This will help in diagnosing damage
outbreaks, judging the efficacy of imposed solutions, and pre-
dicting future problems. This aspect of the formalized program is
particularly key in helping to evaluate the risk associated with
extending outage intervals. As discussed in detail below, a first
order analysis to judge the likelihood of a future problem is
typically based on an evaluation of unit or industry-wide history.
Without a formal means of accruing the necessary information,
such an analysis will have to rely on generic data.
ECONOMIC EVALUATIONS
An economic assessment of technically feasible options is
central to the correction of turbine damage. Each organization has,
or will develop, a preferred means of performing such analyses
when faced with a run/repair/replace decision. Some basic
concepts about such analyses are presented here.
It is interesting that there is a long history of economic account-
ability related to thermodynamics and power production, in fact it
was necessary during the earliest evaluations of thermodynamics to
have an effective accountancy for the forms of energy, so that all
could be equated with the universal standardmoney (Bernal,
1970).
The economic analysis will typically consist of some form of
cost-benefit analysis or, preferably, a discounted cash flow method
such as net present value (to take account of the timing of benefit
streams). An integral but difficult part of either type of analysis is
determining the expected benefits of a particular run/repair/re-
placement, and in the case of discounted cash flow methods, in
determining the timing of such benefits.
Costs to be considered include:
Capital cost of repair or replacement. This can typically be

calculated from original equipment manufacturer (OEM) or
consultant estimates, or, if the work is to be done inhouse, by
comparison with prior projects of a similar nature.
Cost of outage, including replacement power costs.
Cost of ongoing maintenance for a particular option. This may

be obtained from OEM or consultant recommendations, or
expectation from inhouse experience.
Requirement for and cost of periodic inspection or monitoring of

the component.
Benefits to be considered include:
Changes in outage schedule. Run (with existing damage) and

monitoring options may require a more frequent scheduled outage
than if the component is replaced. Such changes should be factored
into the benefit analysis.
Increases in unit output or improvements in efficiency, if relevant.
Improvements in operating flexibility and/or unit reliability.
Benefits of decreased emissions levels, if relevant.

EXTENDING THE INTERVAL BETWEEN
TURBINE-GENERATOR OUTAGES
Worldwide there are strong economic pressures to move toward
longer intervals between major overhauls. For example in North
America, major turbine inspection outages traditionally have been
scheduled every five years with a duration of approximately six to
eight weeks. Current achievable targets for outage intervals are
now 10 to 12 years with a decrease in duration by one to two weeks
(McCloskey and Pollard, 1995; Roemer, et al., 1997).
TROUBLESHOOTING TURBINE STEAM PATH DAMAGE MECHANISMS 107
Obviously, with longer periods between major inspections, there
is an increased risk of equipment failure. Outage extension needs
to be executed with no compromise to reliability of the turbine-
generator.
At the most basic level, what is required to make the extended
outage decision is an understanding of issues such as:
Identification of components that will limit turbine-generator

safe operating life, e.g., what components are at risk by extending
the period between outages?
Periodic check and accurate assessment of current machinery

condition/risk and developing conditions. In many cases, this can
be performed using a fiberscope and video probe to examine the
condition of the control, reheat, and exhaust stage blading.
Application of methods for tracking and monitoring the critical

components; ideally methods should be utilized that can provide
online, real-time reports on accumulated damage or performance
degradation.
Risk and decision analysis based on probability of failure for

components being monitored. Such assessments should be able to
assess the risks of deferring inspections and take into account a
specific machine type and operating and maintenance history. The
probability and consequences of outage extension decisions should
be calculated.
Assessment of operation and maintenance practices and the

effects on machinery condition/risk.
A proper, quantitative, probabilistic engineering analysis can
provide the foundation on which the risk of outage extension issue
can be judged, particularly when combined with an economic or
financial analysis of the implications of the outage extension
decision. A schematic showing the overall problem is shown in
Figure 4. Lengthening the interval between inspections increases
the equipment failure cost, but decreases the inspection cost. The
overall objective is to minimize the total cost.
Figure 4. Optimized Turbine Inspection Interval as Function of
Failure and Maintenance Costs.
A number of methods have been proposed that can be used to
obtain estimates of the probability of failure. (McCloskey and
Pollard, 1995; Latcovitch, 1997). Any such methodology should
rank components for inspection, focus inspections according to
risk, and allocate inspection resources cost effectively. A balance
between economics and safety constraints is inherent in such risk
assessment.
Three-level approaches will include such steps as:
Level 1Industry risk data can be combined with unit-specific

experience to establish a probability of failure, and from that to
establish a net present value versus time for the unit. Such a Level
1 will be formulated to provide guidance about overhaul interval
optimization even if no monitoring or engineering analysis has
been done on a specific component. It therefore relies on statistical
analysis of failure histories. A generic database, such as the North
American Electric Reliability Council Generation Availability
Data System (NERC GADS) database, can provide knowledge of
the high-risk components for a particular unit type, along with
history-based probability curves for the highest risk components.
Knowledge of unit-specific conditions, as derived from interviews
with plant personnel, can also be entered into the calculation of
failure probabilities.
The calculation of net present value will be constrained by
maintenance budget and forced outage rate limit. Figure 5 indicates
schematically the analytical methodology of this level of analysis.
Using such an approach, a net present value curve is calculated by
analysis; however, choice of outage interval is further constrained
by limits on the probability of failure.
Figure 5. Determination of Net Present Value as Function of
Scheduled Versus Forced Outages.
Level 2Specific component performance and integrity can be

evaluated using a rules-based approach to assess key parameters
such as stresses. At this level, results from tools such as finite
element models, coupled with periodic monitoring to refine the
estimate of probability of failure will be utilized.
Level 3Applies online sensor inputs to assess the conse-

quences of changes in operating conditions and continuously
update the probability of failure. Level 3 would apply measured
unit data to update component life analyses from a Level 2
analysis. It will track damage accumulated during operating
periods.
An overhaul outage inspection interval needs to be optimized by
net present value (NPV) and constrained by (McCloskey, et al.,
1999):
Maintenance budget limits.
Forced outage rate limits.
Safety limit, expressed as probability of failure or risk limits.

The system will track:
Cumulative damage or performance degradation,
NPV incremental and cumulative cost of degradation by turbine

section,
Automate the performance of risk/decision analysis with proba-

bilities of failure and their associated costs.
Shortening Steam Turbine Outage Length
Large economic savings are also inherent in minimizing the
length of scheduled outages. Potential timesavings that are being
actively pursued include:
Preparation
Listing qualified sources
Premodeling of blade disc stages for damage types and
locations that are expected to require analysis or decision about
repair choice. Such activities typically include a database of
stresses.
Establishing databases of material properties, chemistry
effects, and surface treatments for rapid run-repair decisions
Support repair specifications for quality assurance of blades,
discs, partitions, seals, bearings, spill strips, and packing glands
Having adequate spares available
Shutdown and startup

Procedures, practices, and techniques are being compiled that
can reduce the margin of conservatism in generic loading and
starting curves.
Disassembly
Advanced bolting and coupling techniques
Cleaning and NDE of key components
Automating the recording of clearances during tear down
Outage activities
Making alignment changes to rotors and couplings with the

minimum number of moves
Potential for modifications to allow bearings to be isolated and

drained on an individual basis, as well as other potential time
savings in the oil flushing process
Assembly
Optimization of assembly procedures such as internal and unit
realignment and rebalancing
ROOT CAUSE INVESTIGATION
OF TURBINE STEAM PATH DAMAGE
This tutorial is focused on problems with the turbine blades,
rotors, discs, and seals. For each specific problem, topics include
microscopic features of the damage mechanism, common
locations, and susceptible components, failure mechanisms and
root causes, determining the extent of damage, repairs, and inter-
mediate and long-term actions to be taken. The following is a list
of the most prevalent turbine steam path damage mechanisms.
(Please note: Because of schedule limitations this tutorial will
cover only those damage mechanisms shown in italics.)
Creep in high pressure (HP) and intermediate pressure (IP)

rotors
Creep and high-temperature damage in HP and IP blades
Overheating caused by blade windage
Solid particle erosion
Deposit effects and removal in HP, IP, and low pressure (LP)
turbines
Copper deposition in the HP turbine
Low and high cycle fatigue in LP, IP, and HP blades
Fretting wear and fatigue
Environmentally related damage in blades and blade/disc

attachments
Pitting and crevice corrosion
Corrosion fatigue in LP blades
Stress corrosion cracking in LP blades and around the disc rim

and blade attachments
Liquid droplet erosion of rotating and stationary blading
Water induction damage, flow-accelerated corrosion, and

moisture-related damage
Training and clear directive are critical for each group to have an
appropriate role in preventing turbine damage. Without specific
directives, it can be very difficult for operating personnel to
convince system control personnel that significant conditions in the
unit are harmful to the turbine. Figure A-4 of APPENDIX A
provides a flowchart for the investigation of steam path damage or
failures. As shown, there are three avenues open to the investi-
gator(s) depending on the status of the event:
Turbine not opened, damage indicator foundThe turbine is

unopened, but an indicator listed in Table 14-1 in McCloskey, et
al. (1999) provides an alert that damage is accumulating in the
turbine. Indicators are discussed in more detail later in this
tutorial. Table 14-1 (McCloskey, et al.,1999) can be used to point
the investigator toward the correct mechanism, actions to evaluate
each indicator in more detail.
Turbine open, damage found by inspection during scheduled

outage or as a result of a failure that forced an outageThe
turbine is open and damage has been found. The damage may have
caused a shutdown, such as a failure that released broken blades
into the condenser or an extraction line, or damage may have been
found during a planned shutdown. The features of damage
(macroscopic, microscopic, and locations) can thus be used to
identify the possible mechanisms for either case.
Unit precursor observedTable 14-1 (McCloskey, et

al.,1999) can also be utilized to determine which mechanism may
result from a particular precursor. Precursors are also discussed
below.
As shown in APPENDIX A Figures A-4 and A-5, each of these
three paths is an entry point for a series of actions to work through
confirmation of mechanism(s), determination and confirmation of
root cause, (fatigue, corrosion fatigue, and stress corrosion
cracking), and taking short-term and long-term actions to prevent
or minimize future damage by this mechanism. A final, but often
overlooked, step is to look and consider carefully whether the
damage in the turbine steam path is a warning or precursor to
damage occurring in the boiler, condenser, feedwater heaters,
piping, or other major system components.
Case Studies of Cracking and Damage
of Blades in Low Pressure Turbines
Figures 6 and 7 are typical generic examples of the diagnosis of
cracking and damage of blades in the LP turbines of fossil and
nuclear units. APPENDIX A Figure A-5 provides screening
questions to direct an investigator to quickly determine the most
probable damage mechanism. Then, in the relevant chapter(s) of
McCloskey, et al. (1999), the investigator will find additional
means to confirm the initial diagnosis.
Figure 6. Combination of Pitting, Corrosion Fatigue, High Cycle
Fatigue in Low Pressure Blade Airfoil Section.
Figure 7. Evolution of Cracking in LP Blade from Corrosion, SCC,
LCF, and HCF.
Fatigue, corrosion fatigue (CF), and stress corrosion cracking
(SCC) of major steam turbine components, such as blades, discs,
and rotors, have been consistently identified among the main
causes of turbine unavailability. Particularly susceptible are
rotating blades in the phase transition zone (PTZ) of low pressure
turbines that have historically been the leading cause of steam
turbine unavailability for large fossil fuel plants. SCC of discs and
corrosion fatigue of blades and their attachments also affects
nuclear units in phase transition regions. The economic impact is
even higher than in fossil units.
In McCloskey, et al., (1999), several chapters look at pure
fatigue of blades, i.e., in the absence of environmental effects;
other chapters examine the effects of pure environment, leading
to damage such as pitting and localized corrosion. Many more
chapters examine the synergistic effects of static and dynamic
stresses, pitting from the steam environment, corrosion fatigue of
blades, SCC of disc rim attachment areas, and SCC of blades (refer
to APPENDIX A Figures A-6 and A-7).
Fatigue in Low Pressure Blades
Fatigue in LP turbine blades, with or without environmental
effects, is one of the most common underlying causes of steam
turbine failures. This tutorial looks at the pure mechanical (i.e.,
without environmental) aspects of cracking by cyclic loads in LP
blades. It cannot be overemphasized that any blade failure by
cracking that occurs in the phase transition zone of the LP
(typically the last two rows in fossil units and the area beginning
anywhere from about the L-3 to L-6 rows in nuclear units) will be
influenced by the effect of the local environment.
Unfortunately, although fatigue is a very common damage
mechanism, many of the analysis methods for evaluating the root
cause and most of the options for preventing fatigue damage will
require users to seek outside assistance. Thus, this tutorial covers
fatigue in some detail so as to provide an understanding of the
underlying issues. In those cases where the influence of environment
is extensive, the operator may have significant control over the
incidence of failures by the careful control of steam chemistry.
Nature of Features of Fatigue Damage
The fracture surface of a fatigue failure nearly always consists of
an initiating defect, a long section of incremental crack growth,
and a final failure by overload.
Macroscopically, high cycle fatigue (HCF) typically manifests
in a relatively smooth, flat surface with beach marks in the
propagation region. The beach marks are macroscopically visible
ridges representative of transient conditions. Such changes may be
in the load level or in environment. Both beach marks and
microscopic striations (discussed below) expand concentrically
from the fatigue origin or origins and thus can be used to help
identify the site of initiation. Oxidation or corrosion of the crack tip
will lead to discoloration of the metal and help highlight the
benchmark. Figure 8 shows a typical high cycle fatigue crack that
has occurred at the intersection between the blade airfoil and a
tiewire (Sanders and Southall, 1993).
Figure 8. High Cycle Fatigue Failure of Low Pressure Blade at
Intersection of Airfoil with Tiewire and Stellite Moisture
Impingement Wear Strip.
Microscopically, high cycle fatigue cracking is typically
straight, transgranular, and shows fatigue striations. The striations
are closely spaced ridges that indicate the crack tip at various
points in time.
Low cycle fatigue (LCF) will differ in that there is typically
mechanical deformation at the failure surface, i.e., stresses are
sufficiently large that they will cause plastic deformation at the
leading edge of the crack. Figures 9 and 10 show a low cycle
fatigue failure of an L-1 blade. Although low cycle fatigue damage
per cycle is significant, the number of large strain cycles that drive
such damage is limited, usually less than 1000 cycles for base-
loaded machines, and less than 10,000 for topping machines. As a
result, the damage caused by crack propagation under low cycle
fatigue is localized, i.e., near the initiation site. However, once the
crack begins to grow, it is influenced by the much more numerous
strain levels that result in high cycle fatigue. Once a blade begins
to be influenced by high cycle fatigue, the remaining life of the
blade is very limited, only on the order of days or weeks. Thus, in
blades, the evidence of low cycle fatigue will typically appear only
in the area near the initiation site, while the majority of the surface
will show features of high cycle fatigue (Laird and Duquette,
1972).
In blades, the region of final fracture is typically fairly small
dimensionally so that common features of fracture such as chevron
marks (sharp V-shaped patterns whose tips point back toward the
origin) will generally not be obvious.
If there is evidence of staining or deposition on the fatigue
surface, it is highly likely that there has been a contribution from
the steam and water chemistry environment.
Susceptible Units and Locations
Fatigue is ubiquitous; it can cause damage in the blading of all
turbine types and stages. It tends to be more prevalent in the latter
stages of LP turbines because the length of the blades leads to
higher stress levels and allows for a variety of resonances.
Location on an individual blade. Fatigue damage can occur
almost anywhere on a blade, particularly where there is a stress
concentration. As a result, on LP blades, the roots, steeple fillet
regions, shroud tenons, tiewires, and tiewire holes are the most
susceptible. For example, Figure 11 shows the fatigue failure of an
LP blade that was caused by breaking of the outer tiewire. The
subsequent change in frequency caused the blade to fail by high
cycle fatigue, with the damage originating at the inner tiewire hole.
Figure 12 illustrates the most common locations of fatigue damage
on LP blades.
High cycle fatigue can occur anywhere along the length of the
blade. One reason for this is that dynamic (vibratory) stresses can
reach a maximum anywhere along the blade length depending on
Figure 9. L-1 (Next to Last) Stage Blade Failure at Base of Airfoil
Due to Low Cycle Fatigue.
Figure 10. Closeup of Low Cycle Fatigue Failure Shown in Figure 9.
Figure 11. High Cycle Fatigue of Low Pressure Blade at Tiewire,
Caused When Crack in Tiewire Changed Natural Frequency of
Blade in Group Packet.
Figure 12. Most Common Locations of Fatigue Damage on Low
Pressure Blades. (H indicates typical locations of HCF; L
indicates typical locations for LCF.)
the active mode shape. This is illustrated in Figure 13, which shows
the level of vibratory stresses for the first five modes of a 3000 rpm
blade. The y-axis in Figure 13 is the maximum relative dynamic
stress. From Figure 13, for example, a failure by the third mode of
vibration might occur at the tiewire as the maximum dynamic
stress occurs at approximately 0.8 of the distance to the blade tip
(Somm, 1976). Low cycle fatigue typically occurs only in areas
near the blade root and is typically caused by speed cycling.
Figure 13. Distribution of First Five Harmonics of Vibratory/
Dynamic Stresses as Function of Blade Length.
Affected rows. Most failures in turbine blading of fossil units
occur in low pressure blades, particularly concentrated in the L-0
and L-1 stages. Unfortunately, although in some cases location by
row may help determine the applicable loading, there can be a
considerable range over which particular causes can lead to blade
fatigue failures.
Each turbine blade row of a particular turbine design tends to
have distinctive problems. For example, the operating life of L-0
rows of a particular turbine design is generally controlled by low
cycle fatigue caused by start-stop cycling, although in extreme off-
design conditions stall flutter may also cause fatigue damage by a
high cycle fatigue mechanism. In contrast, the L-2 and L-3 rows of
the same design are generally controlled by high cycle fatigue
typically as a result of resonance with particular blade-disc modes
with per-rev harmonics of rotational speed (Dewey, et al., 1983).
Affected blades or groups of blades. Fatigue cracking patterns
may indicate the type of loading that lead to a fatigue failure. For
example, cracking has been found to originate in microcracks in
the tenons, induced during assembly of shrouds that subsequently
propagate by steady-state and vibratory stresses. Torsional
vibration is more typical in the shroud/cover whereas axial
vibration (the higher energy mode) tends to be the dominant mode
in the blade root. The dynamic stresses caused by resonances are
higher in the end or next-to-end blades for the most troublesome
modes, such as tangential and torsional vibrational modes.
High cycle fatigue may tend to selectively affect blades as slight
differences in blade manufacturing and installation can result in
slight differences in response to excitations. Flutter, a form of high
cycle fatigue caused by an aerodynamic instability, may result in
clusters of failures. Figure 14 shows the pattern of high cycle
fatigue in a row of freestanding, titanium, and L-1 blades (Rust, et
al., 1990).
Figure 14. Distinct, Closely Tuned Clusters of Blade Failures in Row
of Aerodynamically Unstable Titanium L-1 Freestanding Blades.
In blade groups, the mode of resonance causing a high cycle
fatigue failure can usually be determined by examining where in
the group the failure occurs, and the origin and direction of crack
propagation.
Low cycle fatigue, which is caused by the cycling of centrifugal
stresses in the root that accompanies unit speed changes, will
typically affect multiple blades since groups or individual free-
standing blades in a row experience a fairly consistent amount of
centrifugal loading. However, trailing or leading blades within a
group may experience somewhat earlier failures as a result of
covers or tiewires redistributing the overall centrifugal loads
toward the outer members. Indications that this damage
mechanism is active are shown in Table 1.
Table 1. Indications Damage Mechanism Is Active.
There are few unitwide precursors for this mechanism. One is
detecting vibration in the rotor as a result of imbalance, indicating
a forcing function that, if unchecked, could lead to high cycle
fatigue in blades.
Appraisal Means Indicator
Without Opening Turbine Sudden change in journal bearing vibration and/or change in
phase angle caused by loss of a blade or shroud as a result of
fatigue damage.
Increased vibration of blades may indicate either that fatigue
has become active or that loading is higher than anticipated
and could initiate fatigue.
With Opened Turbine Presence of fatigue damage found by inspection. Loss of
blade.
Unit precursors indicating that this damage mechanism may
have become active.
It should be noted that fatigue will occur in steam turbines,
particularly in the last stages of the LP and first stage of the HP
turbine. A key to the design and fabrication process is to provide
acceptably (long) fatigue life, including an allowance for environ-
mental effects.
Mechanism of Fatigue Damage
Fatigue is the phenomenon of damage accumulation caused by
cyclic or fluctuating stresses. A simple illustration of the nature of
the cyclic loading is shown in Figure 15 where smax = the
maximum stress, smin = the minimum stress, sa = the stress
amplitude or alternating stress, sm = the mean stress (equal to half
the sum of smax + smin), and sr = the stress range.
Figure 15. Graphical Definition of Both Dynamic and Static
Fatigue Stresses.
In turbine blades, fatigue can be either low cycle (high stress) or
high cycle (low stress); there is no fundamental difference in the
mechanism between the two types of fatigue. High cycle fatigue is
characterized by loads that cause only local plastic deformation
(small-scale yielding), while the rest of the component is loaded
well within the elastic range; low cycle fatigue is typically caused
by loads that produce considerably more plastic deformation. The
precise distinction between low cycle fatigue and high cycle
fatigue is somewhat arbitrary. Generally failure that occurs in less
than 104 to 105 cycles is considered low cycle fatigue; failure in a
greater number of cycles is high cycle fatigue.
Low cycle fatigue is incremental crack growth caused by large
stress cycles such as centrifugal stresses that occur during unit
start-stop, overspeed, or thermal cycles. Low cycle fatigue can also
occur if the original design of the blade was inadequate to
accommodate the operating loads, or if the blade contains manu-
facturing defects or shortcomings.
In contrast, high cycle fatigue damage accumulates over a much
larger number of cycles at lower stress (strain) levels per cycle.
Many blade failures occur as a result of high cycle fatigue, caused
by a variety of loading conditions. The most typical failure occurs
when the frequency of the excitation is near a resonance frequency
or harmonic of the blade. The rate of high cycle fatigue crack
growth can be rapid as a result of the superposition of dynamic
(vibratory) stresses in combination with the high mean stress
induced by centrifugal loading. The dynamic stresses that develop
depend on the frequency and shape of the exciting force, the
response of the blade, both natural frequency and mode shape, and
the energy dissipated through the various damping mechanisms
present.
A factor that complicates the diagnosis of LP blade failures is
that they typically occur by a combination of mechanisms. For
example, initiation may occur as a result of high stresses at a stress
concentration (low cycle fatigue) with subsequent damage accu-
mulation (propagation) driven by lower stresses more typical of
high cycle fatigue. Further complicating the diagnosis is that in the
phase transition zone, the rate at which both these stages, initiation
and propagation, occurs is dramatically influenced by the local
environment.
Stages of Fatigue Crack Growth
Fatigue is typically manifested as three distinct phases:
Initiation,
Stable propagation of a crack, and
Final failure that ensues when a critical crack size is reached and
failure occurs by fracture or overload.
Fatigue is dependent upon the frequency and magnitude of the
stress cycles and is generally independent of stress duration.
Origins for fatigue cracks can include:
Locally aggressive environment that produces corrosion pits or

troughs, localized corrosion, or local dissolution.
Rubbing or fretting damage.
Stress concentrations such as blade roots, tiewires, shrouds,

tenons, and erosion inserts.
Material processing or fabrication defects such as: forging

segregation, exposure of end grains, laps or folds in the material,
tears in forming or stamping, casting porosity and cold shuts, and
various weld problems such as porosity and cold working.
Grinding or machining tool marks.
Inadequate or improper repairs.

Fatigue, although it takes place under globally elastic
conditions, can occur only with plastic deformation on the
microscopic level, typically only at the crack tip. The sharp crack
grows as a result of alternating stresses that cause crack extension
and blunting. This extension and blunting causes the characteristic
striations. One striation is formed for each cycle, which, in many
materials, can allow for careful estimation of the crack growth rate
by measuring their spacing using an electron microscope.
POSSIBLE ROOT CAUSES OF FATIGUE
The primary root causes of fatigue failures are cyclic stresses.
There are myriad sources of steady-state and dynamic stresses that
affect turbine blades. All the principal sources of stresses in LP
blading, the nature of the loading (steady-state or dynamic), the
source or root cause of the stress, and its contribution to fatigue
through increased mean stresses, as high cycle fatigue or low cycle
fatigue, all need to be carefully identified and analyzed. The key
for the turbine engineer will be to identify the specific cause of the
problem so that proper corrective action can be taken; unfortu-
nately, there are few easy ways to do so. Typically, a blade
assessment including finite element analysis and fatigue life
prediction will be required to fully confirm the underlying root
cause of a failure.
DETERMINING THE EXTENT OF FATIGUE DAMAGE
The choice of inspection method will depend on the location.
Applicable methods include: visual inspection, liquid penetrant
testing, magnetic particle, ultrasonic testing, and eddy current
testing. These methods are listed in order of increasing sensitivity
for crack detection. Visual and magnetic particle methods are the
most widely used for field inspection, although experience has
shown that these methods are not always effective in finding tightly
closed cracks. If cracks are found, the extent of cracking must be
accurately assessed. In many cases, this may require removal of
some blades.
BACKGROUND TO REPAIRS
AND IMMEDIATE ACTIONS
Most of the strategies to correct, or at least to mitigate, the root
cause of fatigue are longer term. Repair, refurbishment, reblading
with available replacement, or removal of a damaged row may be
used as temporary measures to get a unit back online, or in parallel
with longer term actions to deal with the underlying cause. In no
case should the simple replacement of blades be considered the end
point of the indicated actions; if the underlying cause is not
corrected, the failures will typically recur.
When cracks are small, they can usually be removed by local
grinding. This has proven effective in corner cracks at top
serrations in L-0 and L-1 roots. Alternatively, it may be possible to
remove the crack by machining, while still maintaining a sound
load-bearing surface between blade and disc. Leading and trailing
edge cracks can also be blended out. Polishing of accessible
areas such as the trailing edges of blades has been found to be
beneficial by removing pitting (Ortolano, 1987).
Shotpeening is, on balance, beneficial. It introduces surface
compressive stresses that improve fatigue and corrosion fatigue
resistance, although it does not change the materials resistance to
pitting or generalized corrosion. Further, the long-term benefits of
shotpeening are not presently known.
Refurbishment may not be capable of returning damaged blades
to new condition, but may be sufficient to return them to operable
condition. This may result in some loss of efficiency, but the ability
to return the unit to service quickly and with minimum downtime
may justify such a decision.
There is probably no part of a blade that cannot be repaired;
however, as with all repair/replace/refurbish options, an economic
analysis, such as described below, should be performed.
BACKGROUND TO LONG-TERM ACTIONS
AND PREVENTION OF REPEAT FAILURES
Figure 16 provides a generic list of options for addressing
fatigue failures in LP turbine blades. The shaded boxes indicate
those steps or options that can typically be executed by a user; the
others may require outside assistance. It is important that the
underlying loading problem be clearly identified so that the proper
choice of preventive action can be taken. An economic evaluation
of the various options should be the first step in the process.
Figure 16. Long-Term Technical Options for Addressing and
Correcting Fatigue in LP Turbine Blades.
Economic Evaluation of Blade Damage Due to Fatigue
As with many other damage types, there may be multiple
potential solutions. An economic analysis of the options will help
guide the user toward the optimal decision. Such an economic
evaluation, including the required availability of the unit, the type
and cost of repair, the availability of replacement blades, cost of
analysis, testing, cost of potential modifications, and expected life
of any modification should accompany a set of long-term actions.
Analysis of Steam Blade Path Damage Due to Fatigue
Blade analysis is performed for a variety of reasons:
Confirming that fatigue is the root cause of the failures

observed,
Comparing alternative fixes to a problem, and
Estimating future reliability by determining life.

A generic procedure for assessment of blade life when subjected to
fatigue is shown in Figure 17 (McCloskey, et al., 1999).
Figure 17. Low Pressure Turbine Blade Remaining Assessment
Flowchart. (Sections refer to McCloskey, et al., 1999.)
The following describe the assessment outlined in Figure 17. As
it is a generic procedure, the analyst should pick the appropriate
steps depending on the nature and extent of the failure.
Compile inspection data, metallurgical results, and unit data.
Evaluating where the damage is occurring helps determine which
stress sources are causing the problem, and thus narrow the scope
of the more time consuming and expensive analytical methods.
Inspection results should include answers to such questions as:
What is the general nature of the damage? Is rubbing, fretting,

or deformation seen with the fatigue cracking?
What can be learned from the location of failures?
Which stage or stages are affected?
Are the failures in individual blades or groups?
Are groups of blades affected? In groups, are all blades equally

affected? Which blades in the group are damaged (only leading
blades, only trailing blades, both leading and trailing blades, all
blades equally, etc.)?
Where on the damaged blades is the damage occurring?
What can be learned from the geometry of the blade and

attachments near the area of failure? Are there measurable gaps
between the blade root and disc rim attachment? Are tiewire,
tiewire hole, tenon, or shroud tolerances or geometries implicated
in the failure? Are failures associated with a stress concentration?
Can exciting forces be measured? If such forces can be

measured, can they be compared to the speed of rotation?
Can the blade vibration modes be measured directly? Perhaps

the most direct method to confirm the underlying driving force
behind a fatigue failure is to directly determine which blades in a
row are vibrating, the corresponding modes, and the magnitude of
the vibration. The principal means for online vibration
measurement is a time-of-arrival method using magnetic sensors
such as a blade vibration monitor (BVM) shown in Figure 18
(Rozelle, et al., 1989).
Figure 18. Noncontacting, Online Steam Turbine Blade Vibration
Monitoring System.
Information from metallurgical examinations should also be
gathered. A summary of key elements of a generic metallurgical
failure examination is as follows:
Identify the source of initiation such as a manufacturing or

material defect, fretting, corrosion, erosion, or impact.
Evaluate the role of the environment. The first step in this

process is to plot the locations of failure on the heat balance
diagram and on a Mollier diagram. Next is a review of steam purity
recommended limits. The third step is a detailed surface analysis of
deposits and cracks using techniques to determine the presence of
key anions. Is there evidence of significant deposits?
Measure fatigue crack spacing. Can low cycle fatigue be

identified as the primary mode of propagation of the cracking, or is
it high cycle fatigue?
Unit information will also be required, including load history
and chemical history of steam. The load history of the unit may
include such information as:
Unit load cycling (a key determinant of low cycle fatigue),
Load changes (which can help account for thermal fatigue),
Number of overspeed governor trips that have occurred,
Period of time that blades were at overspeed conditions,
Conditions that may have lead to subsynchronous or supersyn-

chronous operation.
The period over which the failure has occurred will be an important
clue and help identify, for example, whether a source of stress
consistent with low cycle fatigue or high cycle fatigue is
appropriate.
The following questions should be considered:
Can failures be related to specific unit operation?
Are cycles to failure related to unit start-stops, for example?
Can failures be related to low load operation?
Can failures be related to operation with high backpressure?

Preliminary identification of the failure mechanism is needed.
From the inspection and metallurgical data it should be possible to
identify the general failure mechanism.
Evaluate available information on similar failures from unit,
sister unit, or industry experience. In some cases, it may be
possible to gain considerable insight about the problem and likely
fixes from past incidents.
Determine whether a detailed analysis is required. Once fatigue
is suspected or has been confirmed, it is likely that a detailed
analysis is required. Only very special circumstances would
change this decision. Such situations would have all the following
characteristics:
The failure is isolated to a single blade or only a few blades,
The cause can be clearly identified,
The fix is straightforward, such as a simple replacement or weld

repair,
It is clear the fix will achieve the owners goals for blade life.
Such a set of circumstances might occur, for example, where there
was an isolated blade manufacturing defect that had been clearly
identified as the source of an isolated fatigue failure.
Define the material properties. These may come from historical
records or open literature values, preferably with confirmation of
critical properties by testing. One of the difficulties in any detailed
assessment is dealing with the natural scatter in actual material
properties. Judgment will be required to balance the amount of
data collected against the cost to do so. Material properties of
interest will depend on the damage type being evaluated but will
typically include:
Strength,
Fatigue crack growth rate,
Fracture toughness, and
Hardness.
If the failures have occurred in the phase transition zone, crack
growth rates corresponding to corrosion fatigue will be more
relevant than those typical of pure fatigue.
Gather and evaluate design information. Is the Campbell
diagram available? Are there obvious blade modes that are more
likely to have had resonance with per-rev excitation (Campbell,
1924)?
Define the geometry of the blade, attachments, and damage.
Dimensions should be specified from plant measurements.
Generate a finite element model of the blade. Models should be
defined using actual dimensions of all relevant stress concentra-
tions, nature of blade groups (freestanding or grouped, integral or
riveted covers, tiewires, etc.), and detail of attachments. If failure
appears to be a disc-blade interaction, the investigator will need to
expand the model to include the disc; rotor modeling may also
need to be included if rotor torsional modes are suspected to be an
underlying root cause of the failure.
Calculate steady-state stresses. This should include an analysis
of such stresses as centrifugal stress, steam bending, and any
steady-state thermal stresses. This analysis should identify
locations of maximum stress and their distribution throughout the
blade. The effect of stress concentrations such as at the root
attachment and in tiewires or shrouding should be included. Three-
dimensional analysis is typically required to identify potential high
stress areas; a two-dimensional analysis may be sufficient to focus
on key locations for more detailed evaluation.
Calculate natural frequencies and mode shapes. Plot a Campbell
diagram or interference diagram to illustrate the relationship of
mode frequencies to rotor speed. Suspect a resonance problem if
blade frequencies are close to per-revolution harmonics. Plot the
modal shapes. Applications of these techniques for the diagnosis of
failures are given in the case studies later in this tutorial. It may be
necessary to take into account the changes in blade frequencies
caused by corrosion, erosion, or deposit build up in the analysis of
underlying root causes. This calculation may also include effects
that occur at operating speed but would not show up in a static
model of the blade such as stress stiffening, causing blade
frequencies to be higher than would be measured at zero rpm or
spin softening (Campbell, 1924).
Confirm with a modal test where possible. Blade frequencies
and modal shapes can be documented at zero rpm and compared
with the finite element results. If they compare well, it is
reasonable to assume that the dynamic behavior of the blade is also
well represented.
Calculate the dynamic stresses in response to unsteady forces
using an appropriate forcing function. These might include such
sources as nozzle-wake interactions, flutter, or other unsteady
dynamic steam forces. Estimate time to failure using fatigue and
fracture mechanics analysis. A typical fatigue analysis will use a
local strain approach that allows for the cumulative effect of
multiple strain sources such as modal resonance and mean strains
from centrifugal loading. Input to the fatigue analysis will include
the material, unit history (start/stops), and operating temperature.
Steady stress amplitude, dynamic frequency, and stress amplitude
determined from prior calculations are also used in the fatigue
analysis. Fracture mechanics will be used to determine the lifetime
after the formation of a crack.
Iterate the analysis to evaluate alternative solutions. Options
need to be compared to demonstrate that superior performance in
fatigue can be expected. This step is critical if geometry or material
changes are anticipated, such as the introduction of longer (or
shorter) shrouding, changing to or from freestanding blades, or
changing root attachment geometry. Where operating practices can
be modified to reduce the rate of damage accumulation, these
effects should also be quantified.
It has been estimated that given the various uncertainties in
material properties, excitation, damping, and cumulative damage
estimates, current blade life estimates are within a factor of three
to four of measured life values (Rieger and McCloskey, 1988). For
this reason, use of a finite element analysis (FEA) code and similar
calculations should be used primarily as relative indicators of
performance, not as absolute predictions of life.
Monitoring of Blade Vibratory Stresses and Mode Shapes
Monitoring of actual blade vibration should be strongly
considered. As a minimum, a means to determine whether any
modification has actually lowered the driving forces on a blade is
recommended. Many operators may also wish to place long-term
online monitors on highly susceptible rows. A continuous
monitoring system to detect rotor vibrations and the resulting
rotor-blade coupling reductions in blade fatigue life can also
correct line operations such as high speed reclosing while taking
into account fatigue life consumption (Tsundoa, et al., 1989).
BLADE DESIGN MODIFICATIONS
Several design changes to blading can be made. These typically
require the participation of outside consulting organizations or
original equipment manufacturers. This category might include
going to freestanding blades, changing from freestanding to
grouped or continuously banded blading, or adding damping
devices between blade groups. Other design changes include:
Reduce rotating weight. This strategy aims at reducing blade

centrifugal stresses by using a lighter shroud (titanium, for
example), cover, or lighter blades (such as by switching to
titanium). Note that tuning options described below may also
reduce weight but with a different intent.
Geometric changes to lower stress concentration. This strategy

also aims to reduce blade stresses, particularly in the root
attachment where cracks have often initiated, by enlarging the
hook radii to reduce stress concentration. Other susceptible
locations that might benefit from modification of geometry
include: vane-platform fillets, tiewire fillets or hole edges, and
cover or attachment discontinuities.
Blade Tuning Options
Reduce/add weight to bladeStiffening the lower region of the

airfoil or by removing material from the blade tip or coverband
assembly can increase the blade frequency (Hesler and Marshall,
1993). The frequency can be decreased by removing material from
the airfoil base or adding material to the blade tip or coverband
assembly. Case Study I later in this tutorial describes in detail how
a resonance problem in the L-2 row was corrected by adding mass
to the tip of the rotating blade.
Add frictional damping or material dampingFrictional

damping, also called mechanical, interface, or Coulomb damping,
arises from the relative motion between contacting parts such as
shrouds, snubbers, damping pins, and root cover sealing plates.
Mechanical damping is the most widely applied form of damping
and can be a significant source of total damping. Material damping
is typically of much smaller magnitude; it is an inherent property
of the blading material.
Change stiffness of blade/discAn example of this option is

continuous blade cover and tiewires (or sleeves) near the blade
midsection of last stage blades intended to provide improved
response to buffeting or stall flutter. The continuous design
provides both increased stiffness and damping in the tiewire
sleeves. APPENDIX A Figure A-8 shows a variety of interblade
connection designs that can be used to change the vibration
response characteristics of blades.
In the U.S., the use of long arc shrouding for tuning purposes was
introduced into boiler feedpump drive turbines (variable speed) in
1973. By 1984, when more than 80 rows of auxiliary turbine blades
were modified to long arcs, the first implementation of continuous
long arc shrouding was made. There are now more than 30
successful modifications of this concept to rows of previously failing
blades. The design consists of using the proper long arc of shrouding,
depending on the harmonic nearest to, or most likely to be exciting
the tangential mode of vibration, and linking the ends of these long
arcs with a Z-shaped joint. In addition, tiewire arcs are the same arc
length as the covers, but overlapped to ensure a continuous tie. Case
Study II shows an example where long arc shrouding covering 42 to
43 blades was used to replace five to six blade groups in order to
reduce the problems associated with tangential vibration modes.
Add/move/change tiewires or tenons.
Mixed tuning of blades. In the case of unstalled flutter, mixed

tuning of blades has been found to provide significant reduction of
a problem (Evans, 1993). This utilizes alternating blades with
natural frequencies sufficiently far apart to decouple the vibrations
within blade groups. This strategy will avoid sustained negative
aerodynamic damping and thus avoid the high levels of
aerodynamic response. Examples of before and after BVM test
results utilizing mixed tuning in steel blades are shown in Figure 19.
The degree of mixed tuning required depends on:
Blade geometry.
Material.
Aerodynamic properties.
Figure 19. Comparison of Original and Mixed Tuned Rotating
Blade Vibration Amplitudes to Reduced HCF Failures from
Unstalled Flutter.
Mixed tuning was first applied to freestanding rows of steel
blades, and has now been used with titanium with excellent results
(Nedeljkovic, et al., 1991).
Reduce/add weight to rotor. The objective is to ensure that rotors

avoid resonance with a frequency equal to two times the electrical
grid frequency.
Operating Changes
Operating changes are one of the few areas of improvement that
are within the control of the operator to reduce fatigue failures in
LP blading. Unfortunately, for the most part, they are not likely to
make economic sense. Thus, they are listed mostly for complete-
ness and for those rare conditions where the fatigue problem is so
dramatic that a temporary change in operating practice is prudent
until the problem can be corrected.
Avoid extreme off-load conditions. Raising the minimum load

and operating at lower backpressure are sometimes used to
improve conditions that lead to stall flutter.
Prevent over or underfrequency operation.

For overfrequency conditions, this can be performed, for example,
by immediate reduction of speed to rated levels following
generator breaker trip. For underfrequency conditions, system load
shedding schemes should be in place to allow system frequency to
return to normal (Kundur, 1993).
CASE STUDY I
ANALYSIS AND CORRECTION OF FAILURES
IN AN L-2 ROW CAUSED BY RESONANCE
This case study describes one example of a significant and
recurring problem in L-2 rows. It includes analysis and confirmatory
testing to diagnose the problem and evaluate the potential solution.
Tuning of the blades by increasing the weight was found to solve the
problem that was caused by resonances (Hesler and Marshall, 1993).
Unit and failure history. The fossil station has two 500 MW
turbines, each with four exhaust flows. Repeated fatigue cracking
had occurred in the coverband assembly and blade tenons of the L-
2 rows following plant commissioning. Over a 10-year period
these failures were responsible for an average 4 percent loss in
availability.
Blade design. The L-2 blades were 318 mm (~12.5 inches) in
length. The blades were arranged in groups of 12 using a
coverband attached to the blade tips with two peened tenons per
blade. Adjacent groups were joined with a short coverband
segment, termed a buttstrap. Each buttstrap spanned a total of four
blades in the joined groups. The buttstrap was installed beneath the
coverband and held by the peened tenons. Blades under the
buttstrap had slightly shorter airfoils to accommodate the 3 mm
(0.12 inch) thick material.
Finite element analysis results. A finite element model of the
bladed disc was developed. This allowed for detailed analysis of
stresses and natural frequencies. The continuous nature of the
coverband eliminated most tangential modes resulting in primarily
axial modes.
Figure 20 shows the Campbell diagram that resulted. The
designation D refers to the nodal diameters. The interference
diagram at zero and 3000 rpm is shown in Figure 21. A modal
shape plot is shown in Figure 22 for a typical axial mode. The
modal shape plot is used to help visualize physically the
deformation that is occurring and aid in interpreting the results of
the Campbell and interference diagrams. The nodes are locations
of zero displacement and the highest deformations occur between
nodes. Understanding where the locations of highest deformation
are located may allow a comparison to the failure locations and
confirm that the calculated modes are those relevant to the failure.
Field and laboratory testing results. Two types of testing, modal
testing at zero rpm and strain gauging at operating speed, were
used to confirm and refine the model and to analyze the proposed
solutions. The modal testing confirmed the strong possibility of
axial mode resonance involving one or more modes at about five
nodal diameters, which can be seen from the interference diagram
(Figure 21). The strain gauge data indicated a strong blade
response at 300 Hz involving the sixth nodal diameter axial mode
(Figure 22). In fact the frequency of the damaging mode was found
to be 298.8 Hz or only a margin of 1.2 Hz from resonance.
Life estimation. Using the strain gauge and finite element
results, the fatigue initiation life of the coverband assembly was
calculated. The life estimate, on the order of a few months, was
consistent with the field experience. It was confirmed that the 300
Hz vibration was the cause of initiation.
Modifications. It was clear from the analysis and testing that
detuning to get rid of the resonance conditions was the appropriate
strategy to pursue. Of the various detuning options available, the
chosen strategy was to lower the blade frequency by adding mass
to the blade. The finite element analysis and modal testing were
reperformed using a specific detuning mass. An additional mass of
38 grams per blade was added (Figure 23). This approach had the
following advantages:
Not changing the airfoil and thus leaving the aerodynamic char-
acteristics intact,
The modifications could be performed without removing the

blades,
The modification affected mass distribution only, stiffness was

not changed. Confirmation by strain gauge testing was performed
after the modification was made by the OEM.
Results. The frequency was shifted 11.8 Hz and 11.0 Hz at
the six and five nodal diameters. As a result the dynamic strain at
300 Hz was reduced dramatically, by a factor of 3.5 on peak instan-
taneous strain. The effect was a tenfold decrease in stress at the
failure site and a fatigue life estimate that exceeded 100 years.
Figure 20. Campbell Diagram of Predicted Natural Frequencies
for Case Study I.
Figure 21. Axial Mode Natural Frequencies and Nodal Diameters
in Interferenced Diagram Format.
CASE STUDY II
HIGH CYCLE FATIGUE OF
L-1 BLADES IN AN LP TURBINE
Analysis and Field Confirmation of the Cause and Retrofits
This case study was drawn from a research project that had
several objectives in addition to just the confirmation of a
retrofitted blade design. As a result, it is more comprehensive in
scope, for example, running finite element analyses with two
Figure 22. Undeformed and Deformed Shape Plots from Finite
Element Model Indicating Three Nodal Diameters.
Figure 23. Photo of Blade Modified by Addition of 38 Grams
Underneath Shroud of Rotating Blade Shifting Natural Frequency
of Blade Down by 11 Hz. (Case Study I)
different programs for comparison. However, the steps taken
provide a guide to those that might be considered.
Unit Information. The unit is oil fired and seawater cooled with
a cross-compound axial-flow turbine. The turbine-generator was
put into service in 1958 with a rated capacity of 215 MW. The L-0
stage blades are 109 cm (43 inches) long and the L-1 blades are
72.4 cm (28.5 inches) long. The L-1 blades are tapered and twisted
with a five-finger root attachment. The fingers are staggered and
attached to the disc rim with three axial pins per blade. The blades
were originally installed in groups of five or six with a 1.3 cm (0.5
inch) diameter solid tiewire and a 3.2 mm (0.125 in) thick shroud.
Blade failures. Cracks had been found in the tiewire, tiewire hole
region, tiewire braze, and shroud during every inspection for a 25-
year period. In 1983, a section of the L-1 blade broke off 5.1 cm (2
inches) above the blade platform. An examination showed high
cycle fatigue was the underlying cause with crack propagation
tangentially. Campbell diagram analysis of expected vibration was
performed and, as a result, the blades were changed from the short
arc groups spanning five to six blades to long arc groups spanning
42 or 43 blades, a quarter of the wheel.
Analysis performed. Finite element models for the six blade
group and the 42 blade group retrofit were developed. The
objectives were to predict the static and dynamic stress distribu-
tions and modal characteristics of the two designs. This
information was then used to predict the life to fatigue initiation.
Testing. Modal tests were performed on the original five and six
blade groups and on the retrofitted long arc blade groups.
Measured natural frequencies and mode shapes were compared to
corresponding values calculated by FEA. Dynamic stresses and
steady stresses were measured on the redesigned blade during
rotating tests using radio telemetry from strain gauges mounted on
the rotating blades.
Strain gauge locations were chosen for highest dynamic stresses
based on a preliminary finite element analysis. Dynamic gauges
were located on the leading edges, beneath the tiewire and 5 cm (2
inches) above the blade platform.
Blade natural frequencies were measured during a series of
ascending and descending speed ramps. The turbine was bought up
through operating speed to overspeed then allowed to coast down.
During coastdown, a stationary steam jet was turned on to provide
a once per-rev impulse. During these steam jet tests, the normal
steam was turned off. The telemetry testing was run over a 26 hour
period. Modal tests were run on a six blade group and on a 42 blade
group.
Modal Analysis and Testing Results. An interference diagram for
the six blade group is shown in Figure 24. Wherever the 1800 rpm
constant speed line crosses a set of nodal diameter modes, a
resonant condition is possible. In the six blade group, as shown in
Figure 24, this occurs near the fourth nodal diameter of the first
tangential mode set, suggesting that this harmonic may have been
the cause of the L-1 blade failures. This conclusion is supported by
the observation that tangential mode vibration produces high
stresses at the location of observed cracking and that the crack
propagation was clearly indicative of tangential mode vibration.
The Campbell diagram would not have identified the potential
resonance since it does not include disc effects or the relation
between nodal diameter and per-rev excitation. Although, as shown
in Figure 25, the Campbell diagram does indicate the possibility of
resonance at 120 and 180 Hz with the second and third modes of
vibration, respectively.
Figure 24. Interference Diagram for Six Blade Group Operating at
1800 RPM (30 Hz) for Case Study II.
Figure 25. Campbell Diagram of Six Blade Group Indicating
Tangential and Axial Modes of Vibration.
A similar analysis for the redesign (42 blade groups) indicated
that this tangential mode resonance could be avoided.
Stress and Fatigue Analysis Results. The steady-state stresses
were calculated using finite element analysis and compared to
strain gauge measurements. Dynamic stresses were calculated with
FEA using an estimate of blade excitation based on one-
dimensional nozzle flow theory. It was confirmed that the retrofit
design would have lower stresses in the tenon and vane region near
the tiewire hole, and, although it would exhibit higher stresses at
the base of the vane caused by axial mode vibration, it would have
much lower stresses for the tangential mode resonance.
Conclusions. Based on the analysis of vibration, stresses, and
fatigue life, the 42 and 43 blade groups were retrofit into the
affected unit.
CASE STUDY III
PROBABILISTIC METHODS APPLIED
TO BLADE ROOT CRACKING
This case illustrates how a probabilistic model of low cycle
fatigue crack initiation can be developed.
Problem. The machining tolerances in the root attachment of
multiple hook designs can dramatically affect low cycle fatigue life
of turbine blading.
Method of Analysis. A probabilistic model was developed that
used a Monte Carlo simulation to incorporate the uncertainties of
root tolerances and material properties. Three random variables
were used:
Gap sizes,
The strain-hardening coefficient, and
The fatigue ductility coefficient.

Figure 26 shows a limited set (51 data points on six bearing lands)
of root tolerances obtained from direct measurements, and the
assumed exponential distribution that was then used in this model
study. In actual field application, considerably more measurements
would typically be available. For this data set, the mean gap size
was 0.0036 mm (0.14 mil); the median gap was 0.0025 mm (0.1
mil). The distributions for strain hardening coefficient and fatigue
ductility coefficient were assumed to be normal distributions, again
based on data available.
Figure 26. Statistical Distribution of Gap Sizes for Root
Attachment in Case Study III.
The simulation procedure started with the calculation of a
maximum elastic stress for a random gap combination. Then the
plastic strain was calculated based on the strain-hardening
coefficient, also randomly chosen. Finally the low cycle fatigue life
was evaluated based on the calculated plastic strain and a randomly
selected fatigue ductility coefficient.
CASE STUDY IV
LAST STAGE BLADE FAILURE
CAUSED BY UNSTALLED FLUTTER
Unit Information. The unit contains a 1300 MW cross-
compound turbine with a double-flow high pressure (DFHP)
turbine and two double-flow low pressure (DFLP) turbines (LP1
and LP2) on the A line, along with a double-flow intermediate
pressure (DFIP) and two double-flow low pressure (DFLP)
turbines (LP3 and LP4) on the B line.
Blade failures. A catastrophic failure of an L-0 blade occurred
just above the platform during testing of an overspeed trip. A
second blade failed from impact with the first failure. The entire
HP line became dynamically unstable because of the large mass
imbalance, eventually causing extensive damage to all components
in the line, including the high DFHP, two DFLP, generator, exciter,
bearings, and turbine auxiliaries.
Prior inspection results. The L-0 blades were inspected approx-
imately four years prior to the failure with wet magnetic particle,
and no damage was noted on the airfoils of the blades.
Results of metallographic analysis. The failure initiated at the
trailing edge of the airfoil from a corrosion pit that was approxi-
mately 0.25 0.50 mm (0.01 0.02 inch) in size. Other corrosion
pits in the same area measured about 0.025 (0.001 inch) deep and
0.05 mm (0.002 inch) wide. No corrosive species were identified
in the blade deposits. No microstructural or fabrication anomalies
were identified in the origin area. The failure surface was found to
be basically transgranular, typically of that resulting from high
cycle fatigue. There were 54 beach marks on the fracture surface
indicating 54 transient events during a four year period during
which the bulk of the crack propagation occurred.
Results of material testing. The ultimate strength, yield strength,
elongation, and reduction in area were found to be within the OEM
specification; thus, material deficiency was determined not to be a
root cause.
Results of analysis of resonance. An analysis was performed to
determine whether blade resonance was an underlying root cause.
The analysis produced Campbell and interference diagrams and
determined that the L-0 blades were well detuned away from
natural frequencies. Verification was completed using a modal test.
The analysis was extended to determine the effect of a crack in the
blade on its resonance frequency. It was found that for a crack
length of 31.75 mm (1.25 inch), the blade was tuned in resonance
with its axial mode; however, as the crack grew beyond that point
it became detuned. As the final failure was at a crack length of 88.9
mm (3.5 inches), it was determined that blade resonance did not
cause crack propagation.
Was stalled flutter a potential root cause? The unit was base
loaded and did not operate below 50 percent load with high
condenser backpressure. For this reason stalled flutter was also
eliminated as a potential root cause.
Was unstalled flutter a potential cause? An analysis of the
potential for unstalled flutter was conducted. It was found that the
available aerodynamic damping to resist nonsynchronous vibration
response to the fourth axial mode was low. Aerodynamic damping
decreases with increased flow rates and increases with increased
backpressure. The analysis found that although the L-0 blades were
predicted to be stable under design conditions, at off-design
conditions of flow > 100 percent and backpressure < 6.68 kPa (2
inch Hg), the blades were predicted to respond strongly (become
unstable) if stimulated by nonsynchronous excitation.
Conclusions. The blade failure was a result of a progressive
failure. Corrosion pits formed, and, as the pits grew, the blade
airfoil became susceptible to significant operating stresses. A
microcrack initiated from the bottom of the pit as a result of a
combination of low cycle fatigue and stress corrosion cracking.
Once the crack reached an advanced length, it propagated by high
cycle fatigue driven by unstalled flutter. The flutter occurred as a
result of off-design operation (high flows and low backpressures).
Solutions. New (spare) rotors were installed in the line A. The
four L-0 rows of line B were refurbished. An online blade
vibration monitoring system was installed. Off-design tests to
detect zones of distress from unstalled flutter were conducted.
Over the longer term, a plan was set up to refurbish all L-0 and L-
1 blades on a 10-year reinspection cycle.
An economic evaluation should be executed in parallel with the
decision about which option to pursue. In most cases, a detail blade
assessment, such as outlined in Figure 17 (McCloskey, et al.,
1999), will be required to identify and confirm the underlying
stress source (Table 2), compare alternative fixes, and evaluate the
expected life of the chosen fix. Three generic approaches to
reducing fatigue damage are design changes, tuning, and operating
changes. The main text contains a more detailed list of generic
choices in each of these categories. The optimum choice will
depend on the source of the problem and the expected economics
of the tradeoffs. The operator may also wish to implement online
monitoring utilizing a blade vibration monitor as a means of antic-
ipating future fatigue conditions.
CORROSION FATIGUE OF LP BLADES
Corrosion fatigue is one of the leading causes of damage in the
rotating blades of steam turbines. It occurs as a result of the
combination of cyclic stresses and environmental effects. Damage
that accumulates by corrosion fatigue typically originates from
pitting or other localized corrosion. Subsequently, the developing
flaw is affected by cyclic loads leading to corrosion fatigue or, in a
few cases, by steady-state loads causing stress corrosion cracking.
Fatigue, corrosion fatigue, and stress corrosion cracking are
closely related. In rotating blades, corrosion fatigue is far more
common, while in the disc rim attachment area, SCC is
predominant. SCC and CF differ in the range of affected materials
and environments. CF affects nearly every alloy, as the crack
growth rate in any environment is typically more rapid than that in
Table 2. Detail Blade Assessment.
air; corrosion fatigue also occurs over a range of electrochemical
potentials, even active dissolution, whereas SCC occurs only in a
narrow range of potentials.
NATURE AND FEATURES OF
CORROSION FATIGUE DAMAGE
Corrosion fatigue cracks are surface initiated and are found in
conjunction with a stress concentration. In many cases in turbine
blading, corrosion fatigue will initiate from a corrosion pit.
However, CF cracks can also initiate from other types of local
damage such as:
Fretting,
Manufacturing defects,
Inclusions,
Microscopic imperfections in the material such as preferential

dissolution of persistent slip bands or by mechanical rupture of the
passive film at slip steps, or
Specific adsorption of species that locally reduce surface energy

(Macdonald, et al., 1985; Laird and Duquette, 1972).
Corrosion fatigue cracks in turbine blading materials can display
a variety of morphologies depending on the environment and stress
levels, including both transgranular and purely intergranular.
However, initiation will typically be transgranular; subsequent
propagation in turbine blading materials is also typically trans-
granular, except in a narrow stress intensity range where it is
possible for propagation to be intergranular.
The surface of the corrosion fatigue crack will typically manifest
a brittle appearance, i.e., little macroscopic evidence of
deformation, and will not be nearly so rough looking as stress
corrosion cracking. There may be some evidence of corrosion
products on the fracture, although often these may not be present.
Typical deposits include white or gray chloride, sulfate, and/or
carbonate deposits that form a local coating over the blade surfaces.
There is generally a loss of sharpness or definition of the fracture
morphology. Other features typical of corrosion fatigue include:
visible striations, crack arrest lines, and little or no branching.
Figure 27 shows developing corrosion fatigue cracks originating
from the roots of two adjacent L-1 blades. Figure 28 shows another
location in the same row in which a final overload and completed
fracture have occurred just below the platform after initiation from
the first hook. Corrosion fatigue and SCC occur under similar
circumstances and may coexist on the same fracture.
Figure 27. Corrosion Fatigue in L-1 Blade. (Crack initiation and
propagation can be seen in first hook (serration) of two blade roots
shown.)
Susceptible Units and Locations for Corrosion Fatigue
Damage by corrosion fatigue occurs in the latter rows of LP
turbines in both fossil and nuclear units starting in the phase
transition zone and extending to the exhaust. The PTZ moves
according to load changes, but is typically near the L-1 row in most
LP fossil turbines and near the L-3 and/or L-4 region of nuclear LP
turbines.
Units going to increasing cycling duty may be subject to
worsened corrosion fatigue problems as:
The blades pass through resonances more frequently since the

unit is ramped up and shutdown,
The phase transition zone shifts, potentially affecting more

stages during transients,
The general steam purity levels are significantly worse during

transients than during steady-state operation,
If the unit is shutdown as part of the cycling operations,

significant degradation of the local environment can occur.
Figure 29 shows the locations most commonly affected by
corrosion fatigue. Although shrouds are typically constructed of
the same material and subjected to the same bulk environment,
corrosion fatigue tends to be less of a problem because of the lower
vibratory stresses. Indications that CF damage mechanism is active
are shown in Table 3.
Stress Type/Load Specific mitigation options
Centrifugal tensile stresses Reduce stresses in blade roots by enlarging the hook radii or other geometry
change to reduce stress concentration.* Improve hook-to-hook contact
between the roots and disc; decrease assembly tolerances.* Reduce weight
such as by use of a lighter shroud, cover, or blade (titanium, for example).*
Adopt freestanding design (eliminate shroud) to reduce weight and thus hook
stresses.
Geometric untwisting* None
Centrifugal bending stresses Not usually practical
Steam bending loads Reduce stresses in blade roots by redesign such as by enlarging the hook radii
to reduce stress concentration.
Synchronous resonance of blades
with a harmonic of theunit running speed*
Identify by analysis those blades that are within
Approximately 10 Hz of the nearest harmonic.
Redesign to reduce resonant stresses such as by optimizing the blade profile,
airfoil, and width.
Tuning strategies, such as:
Add/reduce weight to alter frequencies and resonances
Use Campbell diagram
Add structural material or Coulomb damping to alter resonance and/or reduce
resonance stresses.
Add/move tiewires or tenons to change stiffness of blade or disc, thus altering
resonances and stresses.
Nonuniform flows For synchronous vibrations:*
Identify by analysis those blades which are within 10 Hz of
the nearest harmonic.*
Redesign to reduce resonant stresses
Tuning strategies, such as:
Add/reduce weight to alter frequencies and resonances
Use Campbell and or interference diagram
Add material or Coulomb damping to reduce resonance stresses.
Add/move tiewires or tenons to change stiffness of blade or disc.*
Redesign of steam admission and discharge areas to reduce intensity of
excitation.
For nonsynchronous vibrations:
Will depend on the source
Blade torsional vibration induced
from rotor or disc
Change frequency of rotor by adding/subtracting rotor or blade weight.
Change frequency of blades by adding/subtracting weight or changing the
stiffness of the blades
Provide appropriate controls to prohibit operation outside recommended
frequencies.
Self-excitation For stall flutter:
Avoid operation of unit at extreme off-design load
conditions, specifically increase minimum load and/or
increase backpressure.
Redesign to use continuous tie strategies to provide
restraint at cover tips.
Redesign blade sections to install various damping devices
such as Z cuts in shrouds and loose tiewires.*
For unstalled flutter (not as well understood as stalled flutter):
Establish aeroelastic properties of blades to identify
marginally stable modes.
Use mixed-tuned blades (alternating blades with natural
frequencies sufficiently different from one another) to
decouple aerodynamic forces.
Apply damping devices between blade groups.
Consider derating unit to within load conditions that do not
cause excessive stresses in the blades of the latter stages.
Start-stop transients and overspeeds.* As for centrifugal tensile stresses above
Manufacture and assembly stresses* Depends on source, may require redesign.*
In the case of localized residual stresses from weld repair, heat treatment may
be useful.
Figure 28. Another Location in Same Row as Figure 27 Showing
Where Fracture and Subsequent Blade Loss Has Occurred Just
below Root of Blade.
Unit Precursors Indicating That
this Damage May Become Active
Excessive steam impurity levels (particularly of chloride,
sodium, and sulfate) and the resulting deposition are underlying
causes of corrosion fatigue. If feedwater and steam impurity levels
exceed the recommended limits, such as the result of a major
condenser leak, then corrosion fatigue damage is a possibility. Poor
shutdown procedures are a primary contributor to the aggressive
environment that can lead to corrosion fatigue. High steam cation
conductivity levels many indicate conditions that can lead to rapid
accumulation of deposits and liquid films on blade surfaces; this
may be caused by the steam bypassing the drum separation
equipment.
Effect of Corrosion Fatigue on Turbine Blades
Corrosion fatigue is one of the most damaging mechanisms
affecting the last stages of the LP turbines in both fossil and
nuclear units. Extensive damage including broken blades is typical.
Distress occurring in any of the rotating parts can cause immediate
shutdown of a unit.
MECHANISM OF CF DAMAGE
Damage starts in a localized region as a result of a process such
as fretting, the presence of manufacturing defects, inclusions, and
Figure 29. Typical Locations of Rotating Blades of Low Pressure
Turbine Affected by Localized Corrosion and Corrosion Fatigue.
Table 3. Indications CF Damage Mechanism Is Active.
pitting or other localized corrosion. Once an initial defect has
formed, a rapid decrease in the local fatigue resistance occurs,
leading to damage acceleration through the synergistic effects of
environment and stresses. Where the stresses imposed are cyclic,
either purely cyclic stresses or moderate cyclic stresses imposed on
high steady-state stresses, the resultant mechanism is termed
corrosion fatigue. High mean stresses and moderate cyclic loads in
the presence of an environment form a particularly damaging
combination.
Effect of the Local Steam Chemistry Environment on CF
Corrosion fatigue requires an aggressive local environment. The
local environment consists of two separate aspects:
Dynamic environment produced during operation. These are

local conditions produced by the natural condensation processes
that accompany steam expansion as it moves through the turbine.
Such processes as:
Precipitation of chemical compounds form the superheated
steam,
Appraisal Means Indicator
Without Opening Turbine If the unit is equipped with a blade vibration monitor, it
should be able to detect a change in single blade vibration as
a result of a growing crack.
In the absence of blade vibration monitoring, indicators will
be limited to the detection of severe corrosion fatigue
damage such as the loss of a blade or shroud. This typically
is detected by a change in the amount and phase angle of
journal bearing vibration.
With Opened Turbine NDE survey indicating the presence of corrosion fatigue
cracks
Formation of concentrated liquid films,
Evaporation, deposition, and drying of wet steam on hot
surfaces lead to the formation of potentially corrosive surface
liquid films and deposits.
Environment produced during shutdown. During shutdown,

moist, liquid, oxygenated films form on blade and disc surfaces as
a result of dew point effects. These films result directly from
inadequate shutdown practices.
There is an interaction between the two aspects of the
environment that is central to understanding the corrosion fatigue
process. Figure 30 illustrates schematically how these environ-
mental influences develop and interact, along with cyclic loads, to
produce corrosion fatigue.
Figure 30. Steam and Water Chemistry Environmental and MW
Load Influences on Corrosion Fatigue Flowchart.
The dynamically produced environment concentrates steam
impurities and allows the formation of deposits on blades and disc
surfaces. Particularly important are the formations of liquid films,
which are responsible for supplying the environment for both
corrosion fatigue and stress corrosion cracking to occur. Liquid
films concentrate anions such as chloride and sulfate and reduce
the pH of the local environment, factors that have long been shown
in laboratory tests to contribute to an increase in corrosion fatigue
damage. It should be remembered that these liquid films are also
charged or have a potential that can drive the electrochemical
corrosion fatigue process. Such charges, which change with inlet
steam purity, may be a key driver in the propagation of corrosion
fatigue cracks.
The role of oxygen in the corrosion fatigue process has been
subject to extensive investigation. In some laboratory testing,
increasing levels of oxygen in the test environment have been
found to lead to reduced levels of corrosion fatigue strength in 12
percent cromium (Cr) steels. For example, one investigation found
that the fatigue strength at 5 107 cycles in 3 percent sodium
chloride (NaCl) (deaerated) solutions at 80C (176F) was about
30 percent less than the limit in air; but about one-fourth of the air
limit for aerated 3 percent NaCl. In contrast, other researchers have
found no significant effect of an oxygenated environment on
growth of corrosion fatigue cracks in blading materials (Ebara, et
al, 1983; Holdsworth, et al., 1997). Given the apparently
conflicting results, key issues are:
Why are there differences in the results of various researchers,

but, more importantly,
How do laboratory results relate to the field environment?
What, if anything, does the operator need to do to control

oxygen levels as a partial means of controlling corrosion fatigue?
One of the most important observations from recent work, which
provides guidance for action, is that oxygen does not concentrate
in the early condensate and liquid films under dynamic (operating)
conditions. Levels in the early condensate are < 1 ppb for turbine
steam inlet levels of oxygen in the range of 30 to 250 ppb.
However, oxygen does accumulate in moist, oxygenated films
during unit shutdown if proper recommended practices are not
used.
Recent converging-diverging nozzle tests have shown that
impurities deposited from steam during onload periods (the
dynamic environment) were able to initiate corrosion pitting, a
corrosion fatigue precursor, under the unprotected wet aerated
conditions encountered while a unit is offline (Jonas, Inc.,
1998).
These results confirm that both aspects of the environment play
a key role in producing corrosion fatigue. The dynamic
environment allows for the formation of deposits and the accumu-
lation of potentially corrosive anions in charged liquid films. This
environment occurs when the dynamic stresses that drive corrosion
fatigue cracks are present. During improper shutdown, the
environment provides a source of excessive levels of oxygen along
with moisture, and thus can produce damage leading to eventual
pitting and crevice corrosion.
It has been observed that the presence of small amounts of
oxygen may even be beneficial in slowing corrosion fatigue crack
growth rates (Macdonald and Cragnolino, 1989). This is a result of
two effects:
The passivation of the alloys should be more effective.
The generation of hydrogen through the concurrent cathodic

reaction should be less.
Both effects should reduce the rate of cracking. This position is
strengthened by the observation that there is a lack of environ-
mental effect on crack growth rates for turbine steels at passive
potentials, even in highly aggressive solutions (Rungta and Begley,
1980; Macdonald, et al., 1985). There is a fine balance between
excessive levels of oxygen that can promote pitting (during
shutdown) and accelerate growing corrosion fatigue cracks (in
laboratory tests), and too little oxygen that can speed damage accu-
mulation by preventing passivation of the surface and through the
generation of hydrogen.
Clearly, there is need for the further exploration of the roles of
charged liquid films and oxygen in the bulk and condensing envi-
ronments and their specific roles in the initiation and propagation
of corrosion fatigue cracks. Our present understanding however
indicates that the most troubling aspects of oxygen occur as a result
of the formation of moist, oxygenated deposits during unit
shutdown; the optimum approach is one that controls oxygen
during shutdown and, through steam purity control, deposition and
charged liquid films during operation. This dual strategy is
discussed throughout this tutorial.
Finally, in regard to the overall effect of environment on
corrosion fatigue, it is interesting to compare how strong the envi-
ronmental effect is as compared to the increase of stress that results
from a stress concentration. It has been found in laboratory tests
that mechanical notches (with a stress concentration factor, Kt =
2.5) in pure water reduce the environmental fatigue strength of
titanium (Ti-6Al-4V) and 17-4 PH by about the same factor as an
aggressive test environment of either 22 percent NaCl or 6 percent
wt ferric chloride (FeCl
3
) (Viswanathan, et al., 1983; Bates, et al.,
1984). In contrast, for Type 403, the environmental effect in these
aggressive environments is significantly greater than the notch
effect.
Materials ResponseCorrosion
Fatigue Crack Growth Rates
Figure 31 shows how environment affects the fatigue behavior
of a 13 Cr steel (AISI Type 403) on smooth specimens. Figure 31
is typical of a wide range of materials. There is an obvious
decrease in the cyclic stress amplitude needed to cause failure
(termed the corrosion fatigue strength) for a given number of
cycles, N, with worsening environment.
Figure 31. Corrosion Fatigue Curves of Smooth Specimens of 13
Percent Chromium SS, Exposed to Different Steam and Water
Chemistry Environments.
In laboratory testing, (Bates, et al., 1984), a concentrated NaCl
solution with pH of 10 and less than 20 ppm oxygen causes a
twofold decrease in the fatigue strength in Type 403 from its
pure water value. Decreasing the pH to four or adding large
amounts of oxygen (air-saturated) each results in an additional
factor of two decrease, leading to an eightfold decrease for 22
percent NaCl, pH of four in an air-saturated solution from its
pure water value. Synergistic effects with sodium hydroxide
(NaOH) and oxides of iron, which might be typical of the operating
environment in the LP turbine, further decrease the corrosion
fatigue strength of Type 403. The decrease in fatigue strength can
be as high as 80 to 90 percent from air to an aggressive
environment.
Note that for many materials, true endurance limits can be found
only in an inert environment or vacuum, so that even the moist air
fatigue limit is considered by some researchers as reflecting
corrosion fatigue.
The same behavior is evident on notched specimens of the same
material (Figure 32). Again the allowable cyclic stress amplitude is
markedly decreased as the aggressiveness of the environment
increases. Even for air tests, the presence of a notch greatly decreases
the corrosion fatigue life for a given cyclic stress. These two figures
indicate why pitting, which forms a stress concentrator, is such a
damaging precursor to corrosion fatigue. In many iron-chromium-
nickel (Fe-Cr-Ni) alloys, resistance to corrosion fatigue is directly
related to the resistance to pitting corrosion (Speidel, 1977).
Figure 32. Corrosion Fatigue Curves of Notched Specimens of 13
Percent Chromium SS, Exposed to Different Steam and Water
There are a variety of mechanical, metallurgical, and environ-
mental variables that affect the rate of corrosion fatigue crack
growth in metals (Wei and Speidel, 1972). Some are:
Cyclic stress range, sr = smax smin. This same effect can

be represented by the cyclic stress intensity, DK = f (sr and crack
size, a).
Maximum stress, smax.
Mean stress, sm = (smin + smax)/2. This effect is also expressed

by the stress ratio, R = smin/smax. Increasing the mean stress (or
the stress ratio) will decrease the number of cycles to failure.
Cyclic wave form.
Loading frequency. Decreasing frequency will reduce the

corrosion fatigue strength, likely allowing greater opportunity for
the coupled corrosion process to occur.
Environment.
Metallurgical variables: alloy composition, presence of

impurities, microstructure, and crystal structure.
Mechanical properties: strength, fracture toughness.

One means of representing the complexity of the data is the
modified Goodman diagram or Smith diagram, an example of which
is shown in Figure 33 for a 12 percent Cr turbine blade material.
Experimental data are plotted for the level of mean stress on the
abscissa and for total stress (mean stress plus or minus alternating
stress) on the ordinate. The 45 degree line represents the mean stress
line or no alternating stress. The farther the data fall away from the
mean stress line, the higher the alternating stresses that can be
withstood for a given mean stress and stay below the fatigue strength
of the material. This diagram is particularly useful for illustrating the
effect of mean stress on the corrosion fatigue strength. In Figure 33,
the open circles represent tests run in air. As shown, there is little
reduction for the alternating stress range to failure for this material
in deaerated pure water (dotted line). This behavior is consistent
with the observation that 12 percent Cr material serves very well
when used in reasonably clean environments. However, there is a
marked reduction in alternating stress levels to failure in a 22
percent NaCl (aerated) solution (filled circles).
Figure 33. Modified Goodman (Smith) Diagrams for Fatigue and
Corrosion Fatigue of 12 Percent Chromium SS for Various Steam
and Water Chemistry Environments.
Figure 34 shows that aggressive environments plus high mean
stresses (high stress ratios) lead to marked acceleration of
corrosion fatigue cracks in 12 percent Cr steel. In Figure 34, the
crack growth rate in a vacuum follows the lower curve; in more
aggressive environments, the growth rate can be several orders of
magnitude higher. Growth is also significantly higher at larger
stress ratios (higher mean stresses). Note that in both Figures 33
and 34, the tests were conducted at 60 Hz, frequencies that reflect
those similar to high cycle fatigue loads that have one, two, or three
times resonances with rotor speed.
The precipitation hardened (PH) stainless steels have somewhat
better fatigue and corrosion resistance than 12 percent Cr in
reasonably clean environments, and recent extensive testing of 13-
8 PH and 15-5 PH materials indicate they have substantially
improved corrosion resistance in aggressive environments as
compared with 12 percent Cr. They can be developed to have suffi-
ciently high strength levels for use as last stage blades. However,
there has been some concern over the susceptibility of PH steels to
SCC in aggressive chloride solutions (Denk, 1994).
Duplex (ferritic-austenitic) stainless steel has excellent
corrosion fatigue strength. One problem with the duplex stainless
steels is that commercially available grades have yield strengths
that are less than desired by blade designers (Atrens, et al., 1984).
It is possible however, given their superior corrosion performance
that they may be suitable for LP turbine blades shorter than those
required for the last stage.
Figure 34. Growth Rate of Fatigue Cracks in 12 Percent Chromium
SS as Function of Steam and Water Chemistry, and Cyclic Stress
Intensity Range.
The corrosion fatigue behavior for titanium is completely different
from 12 percent Cr, 17-4 pH, or the duplex stainless steels. Titanium
is fairly insensitive to the environments studied, i.e., there is little
change in fatigue strength between air and an aggressive environment
consisting of 22 percent NaCl (aerated). However, the resistance
decreases markedly for high mean stresses in either environment and
is actually less than for 12 percent Cr steel in some conditions. This
is shown in Figure 35, compiled from several experimental programs
(Speidel, 1983; Atrens, et al., 1983; Rust and Swaminathan, 1983).
How do results from tests conducted in common laboratory test
environments for corrosion fatigue such as 22 percent NaCl,
aerated environments, or 6 percent wt FeCl
3
, relate to actual
conditions in the LP turbine? Analyses of deposits from LP
turbines have indicated an average concentration of chloride of 5
percent (for once-through boilers), with maximum concentrations
up to 45 percent (Bates and Cunningham, 1980). Localized
conditions of high chloride and low pH can exist in liquid films in
the PTZ, and, therefore, these test environments might appear
superficially to be representative of field conditions. The two major
differences are that there is not any appreciable oxygen in the
dynamic turbine liquid film environment, and these liquid films
have a charge/potential relative to the blade material.
Figure 36 illustrates that there is a threshold stress intensity,
DKth, below which defects do not extend by fatigue. Beyond that
stress intensity, crack growth can be rapid, and, in blades, once a
crack begins to propagate, the remaining life is shortmeasured in
days or weeks.
Mechanistic Models of Corrosion Fatigue
There have been a number of mechanistic models of corrosion
fatigue proposed. Four are briefly described here: film
rupture/stabilization, mechanical/chemical dissolution, hydrogen
embrittlement, and/or strain induced corrosion cracking.
Film rupture/stabilizationThere are several variations of this

model, which ascribes accelerated crack growth to the rupturing of
protective films and subsequent reoxidation or corrosion when the
bare metal is exposed to the environment (Magnin, 1983; Ford and
Combrade, 1985). A variation of this model explains the onset of
corrosion fatigue or stress corrosion cracking as being controlled
by crack tip effects that can be explained by the superposition of an
environmental effect and a strain effect (Parkins, 1972).
Figure 35. Modified Goodman (Smith) Diagrams for Ti-6Al-4V
Alloy in Various Steam and Water Chemistry Environments.
Mechanically assisted chemical dissolutionFigure 37

illustrates the basics of this model. Vacancies, caused by
dissolution of the metal surface in a corrosive environment are
driven by a stress field and accumulate at the crack tip; such
coalescence results in incremental crack growth (Galvele, 1987).
Hydrogen assisted (or embrittlement) crackingHydrogen is

produced by the reaction of steel with water. Absorption of free
hydrogen into the metal at the crack tip has been suggested by a
number of researchers as being at the root of corrosion fatigue and
stress corrosion cracking mechanisms (Hickling, 1990; Newman and
Procter, 1990). A schematic of the process is shown in Figure 38.
Strain induced corrosion crackingSimilar to the film rupture

model, this concept involves the local disruption of protective oxide
(Kussmaul and Iskluth, 1990). Destabilization of the oxide can
occur by the environment (dissolved oxygen content, conductivity,
and temperature of the water), mechanical means (strain rate and
strain level), or by material characteristics (such as sulfur content).
ROOT CAUSES AND ACTIONS TO CONFIRM CF
Influence of Environment
The influence of the environment is pervasive. As indicated in
Figure 30, the environmental influence has two main aspects: the
dynamic environment, which occurs during operation, and the
shutdown environment.
Influence of Static and Dynamic Stresses on CF
Corrosion fatigue cracks are driven by cyclic stresses; mean
stresses produced by steady-state loads also have a significant
influence on growth rates. One of the most damaging stress combi-
nations in turbine blades is high mean stress from centrifugal
stresses and moderate cyclic loads, such as from vibration modes.
Figure 36. Cyclic Crack Growth Rate of SS as Function of Range
of Stress Intensity Factors.
Figure 37. Schematic of Mechanical/Chemical Dissolution Model
with Corrosion Generated Surface Vacancies, Migrating to Crack
Tip.
Damaging cyclic stresses can range in magnitude. Large
magnitude stresses such as result from the zero to full centrifugal
stress cycle that occurs during unit starts or overspeeds are clearly
Figure 38. Schematic of Hydrogen Embrittlement Model Showing
How Hydrogen Is Generated at Active Crack Tip and Then
Absorbed into Material.
damaging, but infrequent (low cycle). Lower magnitude, more
frequent (high cycle) stresses include those caused by:
Synchronous resonance of the blades with a harmonic of the unit

running speed,
Nonuniform flows,
Blade vibration induced from the rotor or disc,
Self-excitation such as flutter.

Determining the Extent of Damage Caused by CF
The extent of damage for corrosion fatigue will be determined
exactly as outlined for high cycle fatigue.
Background to Repairs and Immediate Actions
Most of the strategies to correct, or at least to mitigate, the root
causes of corrosion fatigue are longer term. Repair and refurbish-
ment options will be the same as those described for fatigue.
Background to Long-Term Actions
and Prevention of Repeat Damage
Figure 39 outlines most of the available strategies for
confronting a persistent problem with corrosion fatigue. Long-term
actions for dealing with both corrosion fatigue and SCC begin with
an economic and remaining life assessment of the problem.
Thereafter, strategies will generally fall into three categories:
Figure 39. Long-Term Options for Addressing Corrosion Fatigue
in Steam Turbine Blades Flowchart.
Redesigning the blade or attachment to reduce stress levels
Improving steam purity
Changing the bulk material or surface of the blade

Redesign to lower stresses, in conjunction with changes to
improve steam purity, have typically proven to be successful inter-
nationally in reducing LP blade failures by corrosion fatigue in 12
percent Cr material. If such changes are not sufficient, then
changing to a more resistant material, such as blade materials with
a higher chromium content or titanium, is generally recommended
as the next most successful option. The proper choice will depend
on the specific turbine design, the results of the economic
evaluation, and identifying which of the contributing root causes is
most severe.
Economic Analysis of CF Mitigation and Prevention
Proper selection of a long-range strategy for correction of
corrosion fatigue will use both an economic analysis and a
remaining life analysis. Suggested changes will be compared to
identify the one, which can provide the most economic long-term
solution.
LIFE ASSESSMENT OF BLADE CF
Life assessment for corrosion fatigue should provide answers to:
Do blades need to be repaired/replaced immediately or can the

unit operate with the existing damage until a more economically
favorable outage?
If the blades are replaced in-kind, what is the expected life?
If a material upgrade is contemplated, how much additional life

can be expected?
What are the most troublesome stresses, and if mitigation

includes a redesign to lower those stresses, to what degree is the
approach likely to be successful?
Assessment of blade life will typically consist of an analysis of
blade stresses followed by a fatigue analysis. For blades, a typical
assumption is that the time to initiation of a crack is the effective
life. APPENDIX A Figure A-7 shows a generic approach to blade
assessment; this approach is applicable for corrosion fatigue
damage, as well as low and high cycle fatigue.
For stress corrosion cracks, the allowable crack size is limited by
fracture toughness and overspeed, as cyclic loads such as vibratory
fatigue are not dominant. However, the allowable crack size for
corrosion fatigue is limited by the levels of vibratory stress and
other cyclic loads, and the threshold stress intensity factor.
If off-design conditions, such as operation at low load leading
to stall flutter, are a primary contributor to the cyclic loading,
the risk of cracking should be assessed for these conditions and
monitored.
Stress Reduction Options for CF
Reducing cyclic or mean stress levels can markedly decrease the
rate of corrosion fatigue growth. In the 1980s, a declining
incidence of blade failures caused by corrosion fatigue in European
and United Kingdom utilities was attributed to design improve-
ments to decrease mechanical stresses in blades, such as by the use
of:
Freestanding blades (Atrens, et al., 1983).
Continuous banding (Mayer and Besigk, 1983).
Damping design changes and the use of lacing, shrouding, or

similar systems.
A major limitation to this action is that it is normally instituted
by the blade designer and is not within the direct control of the
operator. There are general trends in turbine design toward higher
outputs, better efficiency, and better material utilization, all which
tend to increase the blade stress level and thus could result in a
reversal of this favorable trend.
There are a number of specific actions that can be taken, if
economically justified, particularly if damage is severe and/or
blade replacement is required. General approaches include:
Changing the response of the blade by design modification,
Changing the response of the blade by tuning,
Changing the damping of the blade,
Changing operating procedures, for example, avoiding extreme

off-design operation such as low load, high backpressure operation
that can help to avoid stall flutter.
Within each category are numerous choices. For example,
among the tuning options are: adding or reducing the weight of the
blade, changing to/from freestanding/shrouded blades, changing
to/from blade groupings, adding or moving tiewires or tenons, or
adding material. The choice of design change will depend on an
accurate identification of the underlying cyclic stress problem.
Analysis of blade life will be central in these considerations.
Confirmation testing of the changed design is critical to ensuring
that the change has indeed lowered the troublesome stress. Note
that although mechanical design improvements have had some
effect in decreasing failures, the situation is so complex that there
will always be some vibratory stresses active, e.g., untuned
resonances at high harmonics.
Improving the Steam Chemistry Environment
The role of the environment is dominant in corrosion fatigue. As
indicated on Figure 39, primary alternatives to control this factor
include:
Optimizing or changing chemistry,
Controlling impurity ingress,
Changing unit operating procedures, particularly for shutdowns

and startups.
It is important that a means to determine the efficacy of changes
in steam chemistry be used. Such procedures may include testing
with a converging-diverging nozzle and an early condensate
monitor so that the deposition process can be determined directly.
A final option pertaining to the environment is to improve the
surface finish of blading. Deposition and subsequent concentration
of impurities are a function of blade surface finish, so that improve-
ments may help slow the accumulation of corrosion fatigue
damage.
Change Blading Materials
McCloskey, et al. (1999), list some of the advantages and disad-
vantages of the potential materials for resistance to pitting,
corrosion fatigue, and stress corrosion cracking. Note that
switching to titanium, the most desirable upgrade, provides an
additional benefit of reducing the level of mean stresses. Mean
stresses vary with blade length and design, but are typically limited
to about 275 MPa (~40 ksi); in titanium, mean stresses for a similar
design should be around 170 MPa (~25 ksi) because of the lower
material density (Bates, et al., 1984).
Surface Modification and Coatings
for Mitigation and Prevention of CF
Shotpeening. The most common surface modification to
improve corrosion fatigue resistance is shotpeening. Shotpeening
is, on balance, beneficial. It introduces surface compressive
stresses that improve fatigue and corrosion fatigue resistance,
although it does not change the materials resistance to pitting or
generalized corrosion. It creates only a thin layer of compressive
stress and it does not slow the growth of corrosion pits. Where such
pits extend through the surface layer, the rate of crack growth by
corrosion fatigue is not diminished, as shown in Figure 40.
Shotpeening can create surface roughness, which can allow
increased deposition to occur. The benefits of shotpeening are
material dependent. For example, shotpeening has been found to
improve the fatigue strength of Ti-6Al-4V and 17-4 PH in 22
percent NaCl solution, but was only marginally helpful for Type
403 stainless steel.
Figure 40. Effects of Shotpeening on Corrosion Fatigue Properties
of 12 Percent Chromium SS for Various Steam and Water
Sacrificial Coatings. Numerous coating systems have been
evaluated for use in controlling blade corrosion (Kratz, et al., 1987;
Ortolano, 1987). Although there have been reports of successful
application of such coatings, their use is not extensive, and no
comprehensive database on the long-term performance is currently
available. Although there are ongoing developments, the most
effective coating materials for decreasing pitting and corrosion
fatigue have been found to be ion vapor deposited (IVD)
aluminum, nickel aluminide (NiAl) diffusion coating, and nickel-
cadmium (NiCd) electroplate.
CASE STUDY V
ANALYSIS AND SOLUTION OF
CORROSION FATIGUE ON A BLADE AIRFOIL
Unit and Problem Description. Twenty-three of 1120 free-
standing L-1 blades on a 600 MW fossil fuel unit were found to be
cracked. The unit had experienced about 73,000 operating hours.
The majority of the cracks were found to be at the trailing edge,
about 15 to 20 cm (6 to 8 inches) from the blade tip. Metallurgical
analysis indicated significant corrosion evidencepits and heavy
deposits were evident on the vanes. A review of unit operating
records confirmed periodic contamination from condenser leaks.
The location of cracking seemed to point to an underlying cause of
vibration; when combined with the evidence of corrosion the
failure team suspected corrosion fatigue as the underlying cause
(Figure 41).
Analyses Performed. The following steps, typical of a blade life
assessment, were performed using an FEA code to confirm the
underlying cause and choose among proposed solutions:
The geometry was defined. For this analysis, a freestanding vane

profile with axial entry and a fir tree root with four pairs of hooks
was chosen. Dimensions were specified by the user from plant
measurements.
Figure 41. Campbell Diagram of L-1 Blade for Case Study V. First
Three Natural Frequencies Show Good Separation with Harmonics
of Running Speed, but Fourth Natural Frequency (Second Bending
Mode) Is Coincident with 13th Harmonic of Running Speed.
The user specified the material (403 stainless steel) and

rotational speed (3600 rpm).
A finite element model of the blade was generated.
Steady-state stresses were calculated. An analysis of the stresses

generated by steam forces applied to the blade surface in both
tangential and axial directions was then performed. Maximum
stresses were found to be in the root. However, in this particular
case, the field failures were in the blade and thought to be caused by
the dynamic response of the blade. As a result, the steady stresses at
the failure location were recorded for subsequent analyses.
Natural frequencies and mode shapes were calculated with no

forcing applied. Damping was ignored as its effect on natural
frequency is small for freestanding blades. The effect of stress
stiffening (causing blade frequencies to be higher than would be
measured at zero rpm) was included in the calculation.
A Campbell diagram (Figure 42) was plotted to illustrate the rela-

tionship of mode frequencies to rotor speed. The effect of stress
stiffening can be seen in Figure 41 as the natural frequencies of the
blade (the roughly horizontal lines) increase as the rotor speed
increases from zero to 3600 rpm. The first two modes for the blade
were removed from natural frequencies of the rotor. However, as
shown, the second bending mode (fourth horizontal line up) was very
close to the 13 multiple of the rotor speed (thirteenth per-rev).
A plot of the modal shape for the second bending mode was
made. A nodal line representing points of zero displacement during
resonance of the mode appeared to be about 15 cm (6 inches) from
the end of the blade, which corresponded to the failure location.
Thus, stresses were confirmed to be high in this location whenever
the second bending mode was excited.
Dynamic stresses were then calculated to determine whether the

blade could withstand the resonant stresses (detuning these higher
frequencies being generally impractical as discussed above). The
second bending mode had maximum stress occurring at the blade
edge consistent with the cracked location on the blade. The
dynamic stress level was calculated to be approximately 9 to 12 ksi.
Estimated blade lifetime was calculated from a fatigue analysis.

The fatigue program used a local strain approach that allowed for the
cumulative effect of multiple strain sources such as modal resonance
and mean strains from centrifugal loading. The life was assumed to
be the time to initiation of a crack. User input includes the material,
unit history (start/stops), and operating temperature. Steady stress
amplitude, dynamic frequency, and stress amplitude determined
from prior calculations were also used in the fatigue analysis. There
was evidence of corrosion in the failure so that the effect of
environment was important. The results of the fatigue analysis were:
Figure 42. Failures of Low Pressure Steam Turbine Blade in
Tiewire Hole Due to Stress Corrosion Cracking.
Steady stresses at the failure site: 375 MPa (54.5 ksi)
Dynamic stresses at the second bending mode: 75 MPa (10.9
ksi)
Life in pure steam environment: 1.5 107 hours (infinite)
Life in aggressive environment (22 percent NaCl): 3.5 103
hours (limited)
This indicated that the combination of an aggressive environment
and the resonance or near resonance of the second bending mode
was sufficient to cause failure in a fairly short period.
Evaluation of Potential Solutions. Four alternative solutions to
fix the problem were evaluated:
1. Better control over contaminants in the environment
2. Detuning the blade to reduce dynamic stresses from second
bending mode
3. Change to a more corrosion resistance blade materialtitanium
4. Modify the blade design to reduce stresses. The modified blade
design was considered for both Type 403 stainless steel and for
titanium.
Option 1 was examined first. The primary source of contami-
nants had been condenser leakage. Steps were taken to improve
monitoring and prevent recurrence. However, it was decided not to
rely on just this option. As a result, the last two options (3 and 4)
were considered the most feasible.
The blades were replaced with the modified design using Type
403. There have been no subsequent failures.
CASE STUDY VI
ANALYSIS AND SOLUTION OF
CORROSION FATIGUE ON A BLADE AIRFOIL
Unit Background. A 400 MW reheat unit has a once-through
boiler, seawater cooling, and mixed bed condensate polishers.
Development of the Problem. During a three month period,
cooling water leakage occurred in a discontinuous, but periodic,
frequency. Cation conductivity in the condensate and feedwater
increased up to 2 mS/cm, for about 30 to 60 minutes per day. At the
end of this period, vibration was detected in the LP turbine.
Description of the Damage and Root Cause. The turbine was
uncovered and five broken, freestanding L-2 rotating blades were
found (Figure 43). According to the turbine design data, the blades
were in the phase transition zone. The blades were broken at a
position that was visible as the transition between reddish deposits
at the blade foot and blank metal in the upper part of the blade, in
other words at the phase transition on the blade. A laboratory inves-
tigation found chloride and sodium at the crack site and confirmed
corrosion fatigue as the underlying mechanism. A calculation of
vibration frequencies did not show abnormal conditions.
Figure 43. Five Broken Freestanding L-2 Blades Broken Off at
location of Phase Transition Zone.
Actions. The broken blades were replaced. The cooling water
leak was repaired and a dampening wire was introduced into the
blade design. Thus, both the environmental and stress contributors
were improved.
All these mechanisms are closely related, as shown in Figure 44,
which shows a schematic representation of the interrelationships
and the influence of materials, stresses/strains, and environment.
The regimes of load (zero, sustained/rising, and cyclic) and
environment (inert or aggressive) and the nature of the accumula-
tion of damage determines that stress corrosion cracking occurs
with steady or rising stresses and an aggressive environment;
corrosion fatigue with cyclic stresses in an aggressive environment.
Pitting is most prominently initiated during shutdown when poor
layup practices have been used, thus allowing the formation of a
moist, liquid, oxygenated environment.
DAMAGE ACCUMULATION AS A
COMBINATION OF SYNERGISTIC MECHANISMS
Most environmentally-assisted damage results from a
combination of mechanisms; a factor that complicates its analysis.
In blades, for example, damage often consists of three regions with
differing fracture morphology (Figure 45):
An initiation site, associated with a pit or other evidence of

corrosion,
A region of damage accumulation by fatigue, corrosion fatigue,

or stress corrosion cracking,
An overload fracture area.

Early damage accumulates in a highly localized area, most
commonly a corrosion pit, but which can also be caused by:
Fretting,
Figure 44. Major Material, Environment, and Stress Influences on
Stress Corrosion Cracking, Corrosion Fatigue, and High Cycle
Fatigue.
Figure 45. Failures of Axial Entry Fir Tree Blade Roots in Low
Pressure Turbine Disc Due to Stress Corrosion Cracking.
The presence of manufacturing defects,
Microscopic imperfections in the material such as preferential

dissolution of persistent slip bands or by mechanical rupture of the
passive film at slip steps, or
Specific adsorption of species that locally reduce surface energy.

Steady stresses and surface effects govern the rate of damage accu-
mulation in this regime. Specific signs of a corrosion related origin
will vary by material and local environment. For example, in failed
AISI 403 blades, there is usually a region of corrosion related inter-
granular attack prior to the initiation of crack propagation
transgranularly by fatigue. In AISI 630, evidence is typically
corrosion along intermartensitic boundaries at the initiation site.
Once a corrosion pit has formed, a rapid decrease in the local
fatigue resistance occurs, leading to an accelerating synergistic
effect of cyclic loads and environment. In this phase, growth occurs
as the defect is first affected by the relatively large stress cycles that
accompany infrequent loads such as imposed by unit start-stops.
Damage accumulates in response to these loads with or without an
environmental effect (without = low cycle fatigue; with = stress
corrosion cracking).
When the crack has grown to a sufficient size, damage begins to
accumulate from the more frequent strain cycling caused by
various vibration sources such as: synchronous vibration, nonsyn-
chronous vibration, and rotor torsional modes. Damage
accumulates at this stage by high cycle fatigue or, with environ-
mental assistance, by corrosion fatigue. The final phase is overload
failure when the section thickness can no longer withstand the
applied loads.
Although stress corrosion cracking can occur on blades, its most
significant steam turbine manifestation is in rotors and discs.
Susceptible locations long recognized as major potential problems
include: the keyway, bore, web/disc face, entry slots, steam balance
holes, and the disc rim blade attachments (steeples). Stress
corrosion cracking is surface initiated. In service situations, pitting
or crevice corrosion often precedes SCC, although field failures
have been found that did not initiate at pits. Initiation and
subsequent propagation can be either intergranular or transgranular
with respect to prior austenite grain boundaries. In rotor materials,
SCC is almost always intergranular. When the SCC is transgran-
ular, propagation typically produces flat facets that are observable
macroscopically. The cracks can appear branched (most typically)
or straight: the appearance is a function of applied stress intensity
and environment.
SCC fracture surfaces typically contain easily discernible
regions of initiation, slow propagation, and final rupture. The
region of slow growth will often exhibit corrosion products such as
iron oxides or discoloration compared to the region of final
rupture. Deposits containing sodium carbonate (Na
2
CO
3
) and/or
NaOH frequently have been found on cracked rotors. Sulfides have
also been found in some cases. Multiple, small cracks near the
origin of the main fracture are common. Fractures produced by
SCC typically appear brittle, that is, there is little or no
deformation; fracture surfaces also appear rough in comparison
with corrosion fatigue. Striations are typically not associated with
SCC cracks (Figure 46).
Figure 46. Comparison of Microscopic Photos of Corrosion
Fatigue (Transgranular) and Stress Corrosion Cracking
(Intergranular).
FIVE STAGES IN THE ACCUMULATION
OF STRESS CORROSION CRACKING DAMAGE
Stress Corrosion Cracking Process Stages
Damage starts in a localized, highly stressed region with
initiation from locations with fretting, the presence of manufac-
turing defects, pitting, or another localized corrosion process. Once
an initial defect has formed, damage accelerates through the
synergistic effects of environment and stresses. Where the stresses
imposed are steady-state, the resultant damage is termed stress
corrosion cracking. Failure occurs at stress levels that can be much
lower than those that result in macroscopic yielding. Flaws
propagate by stress corrosion cracking until the loss of section
results in fracture by overload. The mode of damage accumulation
may also change to high cycle fatigue once the stress corrosion
cracks reach a critical size, and failure can occur fairly rapidly,
driven by vibratory stresses imposed by the blades.
The process leading to failure by stress corrosion cracking
consists of five stages (APPENDIX A Figure A-9 and A-10):
1. An incubation period
2. Initiation
3. Stable crack growth by SCC
4. A period of accelerated crack growth by stress corrosion
cracking, high cycle or low cycle fatigue
5. Unstable crack growth or fracture
Stages 1 and 2 are often combined, as are stages 3 and 4,
resulting in three regimes of SCC: initiation, propagation and final
failure. APPENDIX A Figure A-9 and A-10 illustrates the five
steps schematically, indicates the size of defects typical for each
stage or the governing growth rate (da/dt), provides a range of
times for each stage of defect growth, and shows that there are
strategies for dealing with SCC throughout the various stages.
The total time to failure by stress corrosion cracking includes
both the initiation and propagation times. Initiation may be the key
step in the SCC process. General relationships between material
properties, environment, and susceptibility to SCC have been
established by numerous laboratory investigations of rotor
materials. There is a clear effect of material yield strength on time
to initiation: the higher the material yield, the more the suscepti-
bility to SCC initiation. In an analysis of the field experience,
materials with a yield strength less than 750 MPa (~110 ksi) have
been found to exhibit no SCC cracking. In high purity water
(conductivity < 0.2 mS/cm) in laboratory tests, materials show
susceptibility only as a function of yield strength and for yield
strengths in excess of about 1000 MPa (145 ksi). In this high purity
water environment there was no cracking in materials with yield
strength below 1000 MPa (145 ksi) even if the applied stresses
were greater than yield in notched specimens.
Repairs and Actions to Mitigate Stress Corrosion Cracking
There are some short-term strategies that can be used to deal
with SCC in the blade attachment. These strategies can allow the
operator some time before implementing the longer term options.
These include:
Run for a limited time with cracks until a major LP turbine

overhaul can be scheduled.
A variety of mechanical repairs.
Weld repairs. In fossil units, all three options are routine; in

nuclear units, the typical actions have been either mechanical
repair or replacement with a new disc/rotor with essentially no use
of weld repairs, although this is changing as weld repairing in
nuclear units becomes accepted.
Run until the next major overhaul. It may be safe to run until the
next major overhaul even with cracking in the disc rim attachment.
Depending on the particular circumstances, some significant
defects may be tolerated.
A couple of practical points about how stress corrosion cracks
grow may make this option quite rational. First, stress redistribu-
tion occurs as the compliance of the joint changes with a growing
crack. Thus, there may be some unloading around the largest
defects, which can temporarily allow that defect to slow or stop
growing. Second, as noted previously, the rate at which stress
corrosion cracks grow is relatively independent of applied stress
intensity, and thus of flaw size. Therefore, a crack growing by SCC
will not tend to accelerate with increasing length. However, it is
important to remember that once the flaw reaches a sufficient
length such that the damage mode shifts to high cycle fatigue, then
failure can occur in a very short time, and the rate at which damage
occurs is a strong function of crack length.
A remaining life assessment is needed to make the decision
about whether to continue to run with a known defect in the disc
rim attachment area. Unfortunately such assessments cannot
typically be performed within a reasonable period after cracks are
first found. As a result, unless existing assessments are on hand, it
is more likely that such assessments will need to be considered as
central to the long-term and accordingly are discussed with the
other long-term options below.
An owner can prepare for the eventual discovery of cracks in the
disc rim attachment by performing ahead of time the appropriate
stress, fracture mechanics, and probabilistic analyses, based on the
best available data. In this manner, acceptable flaw sizes can be
determined, and those calculations used during inspections to
determine whether immediate action is required. Also, the owner
can lay out what short-term or long-term options will be pursued
as a function of the severity of cracking that is found.
Mechanical Repairs
Field proven mechanical repairs have included:
Flaw removal by grinding, light machining, or skim cutting.

This is the most common means to remove shallow indications.
Skim cutting typically is not an option on finger root attachment
types because of high stresses, particularly with significant crack
depths. Skim cutting is typically followed by polishing to provide
a smooth surface finish and may be followed by shotpeening to
produce surface compressive residual stresses. Shotpeening is also
typically used after machining new dovetail/steeple surfaces. If the
fit up between the blade and steeples is changed, the contact
stresses may increase.
Machine larger radii in the profile to reduce the stress concen-

tration. This will also remove shallow cracks.
Blade removal. One or more blades may be removed, with a

complementary set removed 180 degrees away to maintain
balance, to eliminate loading of cracked sections. This is a useful
alternative if damage is localized to a few blades. Deblading of an
entire row has been used when cracking is extensive around the
circumference. In this case baffles or blocks are installed to
simulate the pressure drop across the row. This is an interim
measure taken until a more permanent fix can be employed.
Disc removal. In some discs with severe SCC in the rim

attachment and keyway, the affected disc is removed and replaced
by a steel or titanium pressure plate (also called pressure block
or dummy block) to maintain the pressure drop across the
section. This is also an interim measure.
For side-entry blades, consider drop notch modification.

Existing blades can be reused.
Install spacers over the notched portion of the rim to reduce

centrifugal stresses at the initiation site.
Two other mechanical repairs fall into the category of activities
that can be conducted during current outage if the replacement
blades are available. These are:
For straddle-mount blades, consider the long shank blades

option. New blades are required. This involves remachining a new
attachment region in the disc below the affected area and installing
blades with longer shanks. This has also been termed the steeple
drop approach (Figure 47). It modifies the existing steeple,
removing SCC damage, and reblading with long shank blades.
The results of computational analysis of stresses, flaw growth
(through fracture mechanics) by low cycle fatigue and high cycle
fatigue and SCC, and remaining life assessment have indicated that
the approach can significantly increase the life of the SCC-
damaged disc and reduce the need for rotor replacement.
Reblade with titanium blades to lower centrifugal stresses.

Combinations of these various mechanical options have been
utilized. For example, one operator chose to use titanium blades for
locations with shallow cracks, titanium blocks (devaned blades) for
deeper cracks, and long shank blades for those cracks that were too
deep. A stress and fracture mechanics analysis was performed prior
to the inspection in order to establish the allowable flaw size ranges
for each option.
Figure 47. Long Shank or Drop Notch Blade/Disc
Modification to Mitigate Need for Replacement or Repair Welding
of Disc/Rotor.
Another operator used skim cutting, polishing, and shotpeening
of shallow defects with selective use of titanium blades to reduce
centrifugal stresses in some of the dressed out areas as a short-term
solution. Over the longer term, they will replace the affected rotors
with upgraded designs.
Note that the mechanical methods that rely on replacement-in-
kind will not improve the susceptibility of the affected area to
further SCC attack. They will likely provide, at best, only the same
life as the original part. In order to improve the lifetime of the
mechanical repair over the original, an improvement in some
condition contributing to the problem will be needed such as to
stresses (for example by changing the fit up), surface conditions, or
environment.
Weld Repair and Surface Modifications to Mitigate or Prevent SCC
Welding is commonly used to repair rim attachment area
damage in fossil units, and has recently been successfully
employed in foreign and domestic nuclear units. Weld buildups can
provide improved performance to the original rotor, primarily by
using a weld material that has superior resistance to SCC. One such
material is 12 percent chromium (Figure 48). Damaged shrunk-on
discs can be repaired in situ or unstacked and repaired off the rotor
or replaced. Damaged rims of integral rotors can be machined off
and repaired by adding a shrunk-on disc or by welding. Repair
welding of rotors, specifically the rim attachment area, is covered
extensively in McCloskey, et al. (1999).
There are a number of surface modifications that logically make
sense in responding to SCC. These include:
Shotpeening to lower surface residual stresses or introduce

compressive stresses.
Use of a corrosion resistant rim or overlay. At least one manu-

facturer is recommending long-term replacement of selected
attachments with the more resistant 12 percent Cr, and weld repair
with 12 percent Cr material. This is a relatively recent option
(Figure 49).
Sacrificial coatings seem like a natural option, but are not suffi-
ciently developed for this application at this time. But OEMs and
other organizations are working on cost-effective remedial
processes.
Longer Term Actions to Prevent SCC
SCC can be prevented in new construction by:
Specifying low yield strength material. How low depends on

other factors such as optimization of the environment along with
the level of operating and residual stresses. However, typical spec-
ifications might call for rotor materials to have yield strengths less
than 900 MPa (~130 ksi).
Using fabrication processes that provide deep compressive

stresses at the rotor surface. Heat treatment, rolling and honing,
and shotpeening have been combined, for example, to induce
surface compressive stresses of about 300 MPa (~43 ksi), which
extend into the material several centimeters.
Figure 48. Steam Turbine Rotor Weld Repair Classifications.
Keeping operating stresses as reasonable fractions of the

material yield strength. Again, the limitation on maximum
operating stresses needed to prevent SCC initiation and
propagation depends on the probable environment, but ranges from
0.6 to 0.9 times the yield strength of the material.
Protecting the turbine, particularly during shutdown, from

damaging environments.
Figure 49. Roadmap of Turbine Disc/Rotor Weld Repair.
APPENDIX A
Figure A-1. Turbine Steam Path Damage Report, Page 1.
Figure A-4. Turbine Steam Path Damage Investigation Flowchart.
Figure A-5. Determination as to Whether Steam Path Damage Mechanism Is Either Fatigue, Corrosion Fatigue, or Stress Corrosion
Cracking Flowchart.
Figure A-6. Contributions of Dynamic/Static Stresses, Structure, Excitation, Damping, Material Properties, and Steam/Water Chemistry
Environment on Blade Life.
Figure A-7. Generic Flowchart for Turbine Blade Remaining Life Assessment.
Figure A-9. Five Stages (Steps) of Damage Accumulation by Stress Corrosion Cracking in Discs and Blades (A).
Figure A-8. Typical Tenon and Lashing Wire Rotating Blade Configurations.
Figure A-10. Five Stages (Steps) of Damage Accumulation by Stress Corrosion Cracking in Discs and Blades (B).
REFERENCES
Atrens, A., Meyer, H., Faber, G., and Schneider, K., 1984, Steam
Turbine Blades, Corrosion in Power Generating Equipment,
New York, New York: Plenum Press, pp. 299-328.
Atrens, A., Mller, M., Meyer, H., Faber, G., and Speidel, M. O.,
1983, BBC Experience with Low-Pressure Steam-Turbine
Blades, Corrosion Fatigue of Steam Turbine Blade Materials,
New York, New York: Pergamon Press, pp. 4-50 - 4-76.
Bates, R. C. and Cunningham, J. W., 1980, Corrosion Fatigue of
Turbine Blading Materials in Operational Environments,
Second Annual Report of EPRI Project RP912.
Bates, R. C., Cunningham, J. W., Dowling, N. E., Heymann, F. J.,
Jonas, O., Kunsman, L. D., Pebler, A. R., Swaminathan, V. P.,
Willertz, L. E., and Rust, T. M., 1984, Corrosion Fatigue of
Steam Turbine-Blading Alloys in Operational Environments,
Final Report CS-2932, EPRI, Palo Alto, California.
Bernal, J. D., 1970, Science and Industry in the Nineteenth
Century, Bloomington, Indiana: Indiana University Press.
Campbell, W.,1924, The Protection of Steam Turbine Disk Wheels
from Axial Vibration, ASME Proceedings, Cleveland, Ohio.
Denk, J., 1994, Low Pressure Steam Turbine Integrity, Materials
for Advanced Power Engineering Part I, Dordrecth, The
Netherlands: Kluwer Academic Publishers, pp. 157-170.
Dewey, R. P., McCloskey, T. H., and Rieger, N. F., 1983, Analysis
of Steam Turbine Blade Failures in the Utility Industry, Paper
83-JPGC-PWR-20, American Society of Mechanical
Engineers, New York, New York.
Ebara, R., et al., 1983, Influence of Dissolved Oxygen Content
and Stress Concentration Factor on Corrosion Fatigue Strength
of Turbine Moving Blade Materials, 1981 Workshop
Proceedings, Palo Alto, California, Corrosion Fatigue of Steam
Turbine Blade Materials, New York, New York: Pergamon
Press.
Evans, D. H., 1993, Comparison of Unstalled Flutter Predictions
and Field Measurements for Steam Turbine Blades, Stress
Technology, Inc., Proceedings of the Steam and Combustion
Turbine-Blading Conference and Workshop1992, Orlando,
Florida, Proceedings TR-102061, EPRI, Palo Alto, California,
pp. 4-85 - 4-99.
Ford, F. P. and Combrade, P., 1985, Electrochemical Reaction
Rates on Bare Surfaces and Their Use in a Crack Prediction
Model for the Low Alloy Steel/Water System, Proceedings of
the Second IAEA Specialists Meeting on Subcritical Growth,
Sendai, Japan.
Galvele, J. R., 1987, A Stress Corrosion Cracking Mechanism Based
on Surface Mobility, Corrosion Science, 27, (1), pp. 1-33.
Hesler, S. H. and Marshall, J. E., 1993, Diagnosis and Correction
of Recurring Failures in L-2 Turbine Stage, Stress
Technology, Inc., Proceedings of the Steam and Combustion
Turbine-Blading Conference and Workshop1992, Orlando,
Florida, Proceedings TR-102061, EPRI, Palo Alto, California,
pp. 1-61 - 1-80.
Hickling, J., 1990, Strain Induced Corrosion Cracking:
Relationships to Stress Corrosion Cracking/Corrosion Fatigue
and Importance for Nuclear Plant Service Life, Proceedings
Third IAEA Specialists Meeting on Subcritical Crack Growth,
NUREG/CP-0112, ANL-90/22, II, Moscow, Russia.
Holdsworth, S. R., Nougaret, M., Roberts, B. W., and Thorton, D.
V., 1997, Laboratory Stress Corrosion Cracking Experience
in Steam Turbine Disc Steels, Proceedings: Steam Turbine
Stress Corrosion Workshop, Final Report TR-108982, EPRI,
Palo Alto, California, pp. 45-59.
Jonas, Inc., et al., 1998, Steam, Chemistry, and Corrosion, Final
Report TR-108184, EPRI, Palo Alto, California.
Kundur, P., 1993, Power System Stability and Control, New York,
New York: McGraw-Hill, Inc.
Kussmaul, K. and Iskluth, B., 1990, Environmentally Assisted
Crack Growth in a Low Alloy Boiler Steel in High
Temperature Water Containing Oxygen, Nuclear Engineering
and Design, 119, pp. 415-430.
Kratz, J. L., Ortolano, R. J., and Kramer, L. D., 1987, Corrosion-
Resistant Coatings for Low-Pressure Steam Turbines, Final
Report CS-5013, EPRI, Palo Alto, California.
Laird, C. and Duquette, D. J., 1972, Mechanisms of Fatigue Crack
Nucleation, Corrosion Fatigue: Chemistry, Mechanics and
Microstructure, Houston, Texas: National Association of
Corrosion Engineers, pp. 88-117.
Latcovich, J. A., Jr., 1997, Steam Turbine Generator Inspection
OutagesAn Insurers Perspective and Approach, in Fifth
EPRI Steam Turbine/Generator Workshop, Lake Buena Vista,
Florida, EPRI, Charlotte, North Carolina.
Macdonald, D. D. and Cragnolino, G. A., 1989, Corrosion of
Steam Cycle Materials, The ASME Handbook on Water
Technology for Thermal Systems, The American Society of
Mechanical Engineers, New York, New York, pp. 659-1029.
Macdonald, D. D., Szklarska-Smialowska, Z., and Moccari, A.,
1985, Stress Corrosion Cracking and Corrosion Fatigue in
Steam Turbine Materials, Interim Report NP-4074M, EPRI,
Palo Alto, California.
Magnin, T., 1983, An Approach to the Mechanisms of Corrosion
Fatigue Damage, Memoires et Etudes Scientifiques Revue de
Metallurgies, LS7857/7Feb90/js.
Mayer, K. H. and Besigk, C., 1983, Influence of Design,
Manufacture and Operation on the Useful Life of Corrosion-
Stressed Turbine Blades, 1981 Workshop Proceedings, Palo
Alto, California, Corrosion Fatigue of Steam Turbine Blade
Materials, New York, New York: Pergamon Press, pp. 5-19 - 5-
36.
McCloskey, T. H. and Pollard, M., 1995, Development and
Implementation of a Turbine-Generator Outage Interval
Extension Strategy, ASME International Joint Generation
Conference, Minneapolis, Minnesota.
McCloskey, T., Dooley, B., and McNaughton W., 1999, Turbine
Steam Path Damage: Theory and Practice, EPRI Report, TR-
108943 Volumes 1-2.
Nedeljkovic, S. I., Rozelle, P. F., and Seth, B. B., 1991, Design
and Verification of Mixed-Tuned Titanium Freestanding Low
Pressure Steam Turbine Blades, Design, Repair, and
Refurbishment of Steam Turbines, 1991 International Joint
Power Generation Conference, San Diego, California, PWR-
Vol. 13, American Society of Mechanical Engineers, New
York, New York, pp. 203-208.
Newman, R. C. and Procter, R. P. M., 1990, Stress Corrosion
Cracking: 1965-1990, British Corrosion Journal, 25, (4), pp.
259-269.
Ortolano, R. J., 1987, Guide for the Use of Corrosion-Resistant
Coatings on Steam Turbine Blades, Final Report CS-5481,
EPRI, Palo Alto, California.
Parkins, R. N., January 1972, Stress Corrosion Spectrum, British
Corrosion Journal, 7.
Rieger, N. F. and McCloskey, T. H., 1988, Turbine Blade Life
Assessment, International Conference on Life Assessment
and Extension, The Hague, The Netherlands, pp. 219-233.
Roemer, M. J., Dewey, R. P., Atkinson, B., Mauney, D. A., and
McCloskey, T. H., 1997, Turbine-Generator Maintenance
Outage Optimization: Probability/Risk Assessment of Net
Present Value, Proceedings of the International Joint Power
Generation Conference: Volume 2: Power, Denver, Colorado,
PWR-Vol. 32, American Society of Mechanical Engineers,
New York, New York.
Rozelle, P. F., Evans, D. H., and Seth, B. B., 1989, Development
and Application of a Blade Vibration Monitor, Latest
Advances in Steam Turbine Design, Blading, Repairs,
Condition Assessment and Condenser Interaction, 1989 Joint
Power Generation Conference, Dallas, Texas, PWR-Vol. 7,
American Society of Mechanical Engineers, New York, New
York, pp. 37-45.
Rungta, R. and Begley, J. A., 1980, Effect of Cathodic Potential
on Corrosion Fatigue Crack Growth Rates of a Ni-Cr-Mo-V
Turbine Disc Steel in Room Temperature Caustic
Environment, Metallurgical Transactions, 11A, (5), pp. 821-
830.
Rust, T. M., Seth, B. B., and Thompson, T. L., 1990, Application
of Titanium to Low Pressure Transition Stage Turbine Blading
at TU Electric, Titanium Steam.
Rust, T. M. and Swaminathan, V. P., 1983, Corrosion Fatigue
Testing of Steam Turbine Blading Alloys, 1981 Workshop
Press, pp. 3-107 - 3-134.
Sanders, W. P. and Southall, W. R., 1993, A Guide to the
Mechanical Condition Assessment in the Turbine Steam Path,
Proceedings of the Steam and Combustion Turbine-Blading
Conference and Workshop1992, Orlando, Florida,
Proceedings TR-102061, EPRI, Palo Alto, California, pp. 2-3 -
2-20.
Somm, E., 1976, Problems in the Development of Last Stage
Blades for Large Steam Turbines, Trans. Inst. of Fluid Flow
Machinery of the Polish Academy of Science, 70-72, Third
Scientific Conference on Steam Turbines of Great Output, pp.
55-79.
Speidel, M. O., 1977, Corrosion Fatigue in Fe-Cr-Ni Alloys,
Stress Corrosion Cracking and Hydrogen Embrittlement of
Iron-Base Alloys, Houston, Texas: National Association of
Corrosion Engineers, pp. 1071-1103.
Speidel, M. O., 1983, Corrosion-Fatigue of Steam Turbine Blade
Materials, 1981 Workshop Proceedings, Palo Alto, California,
Corrosion Fatigue of Steam Turbine Blade Materials, New
York, New York: Pergamon Press, pp. 1-1 - 1-23.
Stodola, A. and Lowenstein, L.,1905, The Steam Turbine, D. Van
Nostrand Company, Boston, Massachusetts: Stanhope Press.
Tsundoa, E., Mimuro, H., Hisa, S., Sakakida, H., and Mori, S.,
1989, Torsional Vibration Evaluation Technique for Large-
Capacity Steam Turbine, Proceedings of the American Power
Conference, 51, Illinois Institute of Technology, Chicago,
Illinois, pp. 109-114.
Viswanathan, R., Wittig, J. E., and Syrett, B. C., 1983, Corrosion
Fatigue of 17-4 PH Turbine Blade Steel in Chloride
Environments, 1981 Workshop Proceedings, Palo Alto,
California, Corrosion Fatigue of Steam Turbine Blade
Materials, New York, New York: Pergamon Press, pp. 4-202 -
4-214.
Wei, R.P. and Speidel, M. O., 1972, Phenomenological Aspects of
Corrosion Fatigue, Critical Introduction, Corrosion Fatigue:
Chemistry, Mechanics and Microstructure, Houston, Texas:
National Association of Corrosion Engineers, pp. 379-380.
BIBLIOGRAPHY
Burton, W. and Ortolano, R., 1992, Field Telemetry Testing of
Long-Arc, Low-Pressure Turbine Blading, Final Report TR-
100216, EPRI, Palo Alto, California.
Ford, F. P., 1979, Relationship Between Mechanics of
Environmental Cracking and Design Criteria, ICM3, 2,
Cambridge, England.
Ford, F. P. and Emigh, P. W., 1985, The Prediction of the
Maximum Corrosion Fatigue Crack Propagation Rate in the
Low Alloy Steel De-Oxygenated Water System at 288C,
Corrosion Science, 25, (8/9), pp. 673-692.
Gandy, D., et al., 1997, State-of-the-Art Weld Repair Technology
for Rotating Components, Final Report TR-107021 V1&V2,
EPRI, Palo Alto, California.
Hickling, J. and Blind, D., 1986, Strain-Induced Corrosion Crack-
ing of Low-Alloy Steels in LWR SystemsCase Histories and
Identification of Conditions Leading to Susceptibility,
Nuclear Engineering and Design, 91, pp. 305-330.
Hxtermann, E., December 1979, Blade Damages in Steam
Turbines: Evaluation of VGB Statistics from 1973 to 1977 and
Basic Comments, VGB Kraftwekstechnik 59, (12).
Kilroy, R. E., Jr., Hershey, T. G., Nowak, E. J., Alice, J. A., and
Peterson, R., 1997, A 12% Chrome Weld Repair Increases
Stress Corrosion Cracking Resistance of LP Finger Type Rotor
Dovetails, Proceedings of the International Joint Power
Generation Conference: Volume 2: Power, International Joint
Power Generation Conference, Denver, Colorado, PWR-Vol.
32, American Society of Mechanical Engineers, New York,
New York, pp. 243-250.
McCloskey, T. H., et al., 1997, Risk Assessment of LP Turbine
DovetailsProbabilistic Modeling of Stress Corrosion
Cracking, International Joint Power Generation Conference,
Denver, Colorado.
Omprakash, V., Lam, T. C. T., Gruwell, D., and McCloskey, T. H.,
1994, Life Extension Strategies of Cracked Disk Attachment
for Low Pressure Steam Turbines, Advances in Steam Turbine
Technology for the Power Generation Industry, 1994
International Joint Power Generation Conference, Phoenix,
Arizona, PWR-Vol. 26, American Society of Mechanical
Engineers, New York, New York, pp. 159-164.
Sarlashkar, A.V. and Lam, T. C. T., 1996, Blade Root Attachment
Evaluation Low-Cycle Fatigue Estimates Based on
Probabilistic Approach, Proceedings of the 1996 International
Joint Power Generation Conference, Volume 2: Power,
American Society of Mechanical Engineers, New York, New
York, pp. 511-516.
Speidel, M. O. and Magdowski, R., 1997, Major Influences on the
Growth Rates of Stress Corrosion Cracks in Steam Turbine
Rotor and Blade Materials, Proceedings: Steam Turbine
Stress Corrosion Workshop, Final Report TR-108982, EPRI,
Palo Alto, California, pp. 157-165.
Stodola, A. and Lowenstein, L., 1945, Steam and Gas Turbines,
1927, New York, New York: McGraw Hill Company, Reprinted
1945, New York, New York: Peter Smith.
Suhr, R. W., 1983, Corrosion Fatigue of a 12CrNiMo Alloy in
Steam and the Effect of Oxygen Content, 1981 Workshop
Press, pp. 4-99 - 4-110.

Troubleshooting ST Path Damage Mechanisms

Uploaded by

Copyright:

Available Formats

Troubleshooting ST Path Damage Mechanisms

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Troubleshooting ST Path Damage Mechanisms

Uploaded by

Copyright:

Available Formats

Thomas H.

(Tom) McCloskey, formerly

Understanding the mechanism and root cause of each incident is

By understanding what causes a problem to occur, it should be

A formalized companywide program for correction, prevention,

Emphasis on the importance of a corporate directive reflecting

Emphasis on training and commitment of personnel. It is not

An emphasis on the importance of a multifunctional team, i.e.,

A recognition that the long-term view of damage prevention is

Training of key personnel (operators, chemists, maintenance

The necessary technical understanding and the solutions needed

A commitment to determining the correct underlying cause of

Remaining life assessment for damage components is a critical

A detailed nondestructive evaluation (NDE) inspection of a

Established shutdown procedures such as to provide a dehumid-

A formal corporate directive or a philosophy statement to

Forming a multidisciplinary team. The turbine condition

The comprehensive reporting and trending of steam path

Attention to indicators that damage is accumulating,

Evaluation of unit precursors to turbine damage,

Optimizing inspection and outage intervals,

Identifying the appropriate root cause of damage,

Determining the residual life of damaged turbine components,

Applying permanent engineering solutions to problems

Maintaining established procedures and careful control over

Monitor turbine performance. This may include all existing

Determine whether specific damage indicators are starting to

Determine whether precursors to turbine damage are occurring

If conditions arise that require turbine work, the T-CAT should

Anticipate and be able to respond quickly to any turbine

Establish the optimal interval between turbine outages (refer to

Anticipate and be able to respond to any damage found during

Review spares policy and establish the optimum inventory.

Determine what ramifications to other parts of the unit may be

Capital cost of repair or replacement. This can typically be

Cost of outage, including replacement power costs.

Cost of ongoing maintenance for a particular option. This may

Requirement for and cost of periodic inspection or monitoring of

Changes in outage schedule. Run (with existing damage) and

Increases in unit output or improvements in efficiency, if relevant.

Improvements in operating flexibility and/or unit reliability.

Benefits of decreased emissions levels, if relevant.

Identification of components that will limit turbine-generator

Periodic check and accurate assessment of current machinery

Application of methods for tracking and monitoring the critical

Risk and decision analysis based on probability of failure for

Assessment of operation and maintenance practices and the

Level 1Industry risk data can be combined with unit-specific

Level 2Specific component performance and integrity can be

Level 3Applies online sensor inputs to assess the conse-

Maintenance budget limits.

Forced outage rate limits.

Safety limit, expressed as probability of failure or risk limits.

Cumulative damage or performance degradation,

NPV incremental and cumulative cost of degradation by turbine

Automate the performance of risk/decision analysis with proba-

Shutdown and startup

Making alignment changes to rotors and couplings with the