VValidationDate).

22740 22740;22741 1 epoxy

Technical Data Sheet
Jotachar JF750
Product description
This is a two component solvent free amine cured epoxy intumescent coating. Specially designed as intumescent
coating to provide fire protection for steel in hydrocarbon pool and jet fires for different types of structures and
equipment. No additional reinforcing mesh is required. To be used as mid coat as part of a complete system in
atmospheric environments. Suitable on approved primers on carbon steel, aluminium and stainless steel
substrates.
Approvals and certificates
BS 476 Part 21 Hydrocarbon Pool Fire curve for structural and divisional fire protection
ISO 22899 Jet Fire Standard for structural and divisional fire protection
NORSOK M-501, System 5A, Rev. 6
ISO 20340 Cyclic Durability Testing
Resistance to Blast Over Pressure
Certified and approved by Lloyds Register of Shipping
Det Norske Veritas Type Approval
ANSI/UL 1709
Colours
grey
Typical use
Typically used in the oil, gas and energy industries. Suitable for both offshore and onshore environments.
In line with all epoxy intumescent technologies, the product is suitable for use on pipe work, vessels or
equipment operating up to 80 C. Should it be necessary to install on substrates operating at higher
temperatures, please contact your local Jotun office for more information.
Additional certificates and approvals may be available on request.
Other
1
Product data
Property Test/Standard Description
Solids by volume
VOC-USA / VOC Hong Kong EPA Method 24
The provided data is typical for factory produced products, subject to slight variation depending on colour.
g/l
100
Flash point ISO 3679 Method 1 100 C
0
All data is valid for mixed paint.
% ISO 3233
Recommended film thickness per coat
Minimum
Maximum
Dry film thickness Wet film thickness Film thickness and
spreading rate
Theoretical
spreading rate
2000 2000 0,5
10000 10000 0,1
(m) (m) (m/l)
Date of issue: 1 August 2014 Page: 1/4 by Jotun Group
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotachar JF750
Typical 6000 6000 0,2
Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.
Surface preparation summary table
Substrate Minimum Recommended
Coated surfaces Clean, dry and undamaged
compatible coating (ISO 12944-4 6.
1)
Clean, dry and undamaged
compatible coating (ISO 12944-4 6.
1)
Surface preparation
Application methods
The product can be applied by
Spray: Use two component heated plural spray unit or modified airless spray (with heating
equipment). See Application Guide.
Note: All pumps used for the application of this product must be certified by Jotun.
Trowel: See Application Guide.
Application
Product mixing ratio (by volume)
Mixing ratio by weight: 1:1
Individual components must have been stored for 24 hours at 25 to 30 C (77 to 86 F). Stir/mix thoroughly
with a power agitator before application.
Jotachar JF750 Comp A 1 part(s)
part(s) 1 Jotachar JF750 Comp B
Thinner/Cleaning solvent
Thinner:
Cleaning solvent:
Jotun Thinner No. 29
Jotun Thinner No. 7
Thinning is typically 5 % by volume for modified airless spray and manual application.
Nozzle tip (inch/1000):
Pressure at nozzle (minimum):
Guiding data for airless spray
31-41
175 bar/2500 psi
Date of issue: 1 August 2014 Page: 2/4 by Jotun Group
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotachar JF750
Drying and Curing time
Surface (touch) dry
Walk-on-dry
6 h 3 h 1 h 1 h
24 h 12 h 6 h 3 h
24 h 12 h 6 h 3 h
Substrate temperature 5 C 15 C 23 C 40 C
Dried/cured for service
Dried to over coat, minimum 6 h 3 h 2 h 1 h
Drying and curing times are determined under controlled temperatures and relative humidity below 85%, and
within the DFT range of the product.
Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.
Dried to over coat, minimum: The shortest time allowed before the next coat can be applied.
Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness. Dry sand sprinkled on the surface can be brushed off without sticking to or causing damage to the
surface.
Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.
Induction time and Pot life
Pot life 45 min 30 min
Paint temperature 15 C 23 C
Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.
Previous coat:
Subsequent coat:
zinc epoxy, inorganic zinc silicate, epoxy, epoxy mastic
crosslinked acrylic, polyurethane, polysiloxane, epoxy
Primers used under this product must be approved by Jotun. Approved primers today include: Barrier Plus,
Penguard Primer, Penguard Tie Coat 100, Jotamastic 90, Penguard Express ZP, Penguard Pro. See Application
Guide.
Packaging (typical)
The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.
Volume Size of containers
(litres)
Jotachar JF750 Comp B 20 / 10 kg
Jotachar JF750 Comp A 20 / 10 kg 20
20
Date of issue: 1 August 2014 Page: 3/4 by Jotun Group
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotachar JF750
Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.
Shelf life at 23 C
12
12
Jotachar JF750 Comp A
Jotachar JF750 Comp B
Storage temperature not to exceed 35 C.
month(s)
month(s)
In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.
Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.
Health and safety
Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.
Colour variation
Products primarily meant for use as primers and antifoulings may have slight color variations from batch to
batch. Such products may fade and chalk when exposed to sunlight and weathering.
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.
If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.
Disclaimer
Date of issue: 1 August 2014 Page: 4/4 by Jotun Group
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com