Spring Isolators

Isolation Hangers
Thrust Restraints
Flexible Connectors
Isolation Bases
Rooftop Isolation Curbs
Neoprene Isolators
Fiberglass Isolators
Air Mounts

Seismic and Wind

Restraint Isolators,
Curbs, Snubbers and
Cable Restraint Kits

Vibration Isolation
Products

Vertical Pipe Riser

Isolation Guides
and Anchors

The Engineering Experience, Manufacturing,

and Testing Capabilities to
Meet Your Application Requirements

www.kineticsnoise.com/hvac

We Are Kinetics Noise Control

Celebrating our 50th year in 2008, Kinetics Noise

Control has extensive experience in the design,
manufacturing and application of innovative products
to control sound and vibration. Kinetics pioneered
development of precompressed, molded fiberglass pad
isolators that would be incorporated into a dynamic new
floor isolation system.
Kinetics Noise Control now produces the industrys
largest selection of inspired products to address
vibration and noise control, room acoustics, and
seismic restraint concerns for almost any application.
Value is added with our experienced team of engineering and customer support personnel ready to work with
you.
Our experienced staff of over twenty (20) technically
trained individuals includes ten (10) licensed Professional Engineers, five (5) holding Masters degrees and
two (2) who have earned Ph.D.s. These individuals are
spread across Engineering and Manufacturing centers
located in Columbus, Ohio (USA), Toronto, Ontario
(Canada) and Hong Kong (China). Their combined
experience spans over 400 years!

Noteworthy Projects
Lou Ruvo Brain Institute, Las Vegas NV
Indu and Raj Soin Medical Center, Beavercreek, OH
Burj Khalifa Tower Dubai
New Quito International Airport, Quito, Ecuador
City of Dreams / Grand Hyatt, Macau
Microsoft headquarters, Beijing
Victoria Harbour Tunnel Project, Hong Kong
The Venetian Hotel and Casino, Macau
Jackson Madison Tower, Jackson TN
City Center, Las Vegas, NV
Montour High School, Pittsburgh, PA
River Oak Hospital, Jackson MS
Roper St. Francis, Charleston, SC
Kaleida Healthcare, Buffalo, NY
Syracuse VA Hospital, Syracuse, NY
LAnse Creuse High School, Harrison Township, MI
Dublin Methodist Hospital, Dublin, OH
St. Anthonys Medical Center, St. Louis, MO

Spring Isolators

Free-Standing Spring Isolators - Model FDS

Highly effective for control of both high and low frequency vibration produced
by fans and pumps located in floors. The model FDS can also be used in
conjunction with wind or seismic restraint and installed outdoors. Operating
static deflections are available up to 4" (102 mm) and with load capacities to
23,200 lbs. (10,523 kg) to compensate for long span flexible floor structures.

Restrained Spring Isolators

Model FLS

Vibration isolators for mechanical equipment, when

the equipment to be isolated has significant changes
of weight during maintenance operations, and for
equipment subjected to external forces or high wind
loads. Operating static deflections are available up to
4" (102 mm) to compensate for long span flexible floor
structures and maintain a high degree of noise and
vibration isolation. Some restrained spring isolators
are designed to provide seismic restraint as well.

Restrained Spring Isolators

Model FRS

Isolate vibration produced by equipment subject to weight

change or external forces, such as air-cooled condensers,
fans, and other rooftop equipment. Support of vertical pipe
risers, where upright motion must be limited, yet the riser
isolated from the building. Operating static deflections are
available up to 2.00" (51 mm), in capacities of up to 3500
lbs. (1588 kg).

Housed Spring Isolators - Model SL and SM

Isolate high and low frequency vibration generated by floor-mounted
mechanical equipment such as air compressors and generators which
are prone to frequent start up and shut down, and equipment that
is slow to reach operating speed. The model SL is designed with a
pre-adjusted snubbing feature to reduce movement as the equipment
passes through critical speed during start-up and shut-down. Available
in deflections up to 1.84" (47 mm), and with load capacities from 35 to
3500 lbs. (16 to 1588 kg).

Fiberglass and Neoprene Isolators

Fiberglass Isolation Pads

Model KIP

Fiberglass Isolation Mounts

Model AC

Neoprene Isolation Pads

Model NP and NG

Neoprene Isolation Mounts

Model RQ and RD

KIP pads are applied in a wide range of noise, shock,

and vibration isolation uses. Recommended whenever a
consistent natural frequency under a range of loads and
permanent load support characteristics are important.
A range of densities and spring rates are available to
provide load-bearing capacities from 1 to 500 PSI (0.07
to 35 kg per sq. cm). Uniquely allow a wide range of
loading on a given isolator while maintaining a constant
natural frequency.

Ribbed neoprene isolation pads used to isolate noise,

shock, and high frequency vibration, generated by
mechanical equipment and industrial machinery located
on a grade-supported structural slab. Applications limited
to pad loadings of 60 PSI (4.2 kg/cm2) for 45 durometer
material, and 120 PSI (8.4 kg/cm2) for 65 durometer
material, and used with equipment having minimum
operating speeds of 3600 RPM.

Isolate audible frequency vibration or noise produced by

small utility vent fans, vain axial fans, high speed motors
and roof mounted exhaust fans with lowest operating
speeds of 1750 RPM when mounted on a grade supported slab or pier with a bolt-down and vertical lift control
feature. The fiber glass pad offers a constant natural
frequency over a wide load range.

Isolate noise and high frequency vibration generated by

mechanical equipment located on a grade-supported
structural slab, pier or load-bearing wall. Equipment
types include close coupled pumps with motors of 5
H.P. or less, small vent sets, low pressure packaged air
handling units and wall-mounted electrical transformers.
Model RQ mounts are also selected for use in seismic
and wind load restraint applications.

Isolation Hangers, Flex Connectors and Thrust Restraints

Isolation Hangers - Models SFH, SRH, SH, FH and RH

Designed to reduce the transmission of vibration and noise from suspend mechanical equipment such as fans,
pumps, air handling units, piping and ductwork. Hanger inserts are designed for up to 50% overload capacity and for
rod misalignment over a 30-degree arc. Brackets will carry 500% overload without failure. Available to 4" deflection
and in capacities to 3,850 lbs. Spring hangers feature Kinetics patented No-Short spring cap which contains indexed
steps to correspond to standard washer diameters for the appropriate rod diameter.

Flexible Connectors
KINFLEX

Prevent stresses due to expansion and contraction and

compensate for misalignment. Absorb the continuing
movement experienced in piping systems because of
varying ambient temperatures, differences in temperature of materials being handled, and differences in
composition. Reduce objectionable noise and vibration
in piping systems, compressors, and other pulsating
equipment.

Thrust Restraint
Model HSR

Counteracts the discharge force created by fans during

operation. Always used in pairs, and best utilized when
located on the centerline of the discharge outlet of the
fan, bridging the flexible duct connector. Uses 1" and 2"
deflection springs in 35 to 3,500 lbs capacities.

Isolation Bases

Inertia Base Frames

Model CIB

Specifically designed and engineered to receive field poured concrete, inertia bases are used to provide a ridgid
mounting platform to support mechanical equipment on vibration isolators. The added mass of the concrete reduces
differential movement between driving and driven members, reduce rocking by lowering equipment center of gravity,
reduce motion of equipment during start-up and shut-down, acts to reduce reaction movement due to operating loads
on equipment, and as a noise barrier.

Structural Frame Bases

Model SFB

Used to support mechanical equipment and provide rigid

platforms for attachment of vibration isolators, without
allowing excessive differential movement between
driving and driven members. Typical uses include
support and isolation of reciprocating chillers, close
coupled pumps, vent sets, packaged air handling units,
centrifugal fans, evaporative condensers, and similar
types of equipment.

Structural Beam Bases

Model SBB

Used to support mechanical equipment provide a means

of attaching supporting isolators while maintaining a rigid
supporting surface for the isolated equipment. Typical
uses include support and isolation of absorption chillers,
hermetic centrifugal chillers, package boilers, cooling
towers, and similar types of equipment.

Rooftop Isolation Rails and Curbs

Roof Curb Rail

Model KSR

Roof Curb Isolation System

Model KSCR

Vibration Isolation Curb

KineticsCurb

Vibration Isolation Curb

Model ESR

Kinetics KSR Isolation Rails are the next generation

isolation system designed and engineered to isolate
packaged rooftop equipment from the roof structure
while providing seismic and wind restraint. Designed
for easy installation, minimum interference with equipment overhang, the Kinetics KSR goes well beyond
internal isolation by reducing casing radiated vibration
caused by turbulent air flow as well as compressor
and fan vibration.

Complete curb and isolation system with Internal seismic

and wind restraint for larger roof top equipment.
Accessible and adjustable 1, 2 or 3" deflection springs,
support hardware for supply and return duct, EPDM air
and weather-tight seals.

Affordable, easy-to-install, all-in-one roof curb AND

vibration isolation for under 20-ton packaged rooftop
units! Standard features include internal seismic and
wind restraint, supply and return support hardware and
EPDM air and weather tight seal.

Heavy-duty, complete vibration isolation curb for the

BIG rooftop unit jobs! Code compliant seismic & wind
restraint, access ports for each isolator to inspect, level,
or change springs after equipment placement. Up to 4"
deflection, powder-coated steel springs with 50% overload capacity. High-frequency noise isolation pads

Sound and Vibration Isolation Curb

Sound and Vibration Isolation Curb - Model ESSR

The Kinetics ESSR is the only isolated curb system that addresses all four noise sources associated with packaged
rooftop equipment. The ESSR incorporates all the features of our ESR vibration isolation curb with our aerodynamic
acoustical silencers; return air plenums and NOISEBLOCK STL panels. This gives you a noise control system
that addresses all the noise and vibration concerns of your packaged rooftop equipment: vibration from the rotating
equipment and casing radiation, duct-borne noise from supply and return fans, and breakout noise from the fans and
compressors into the space below.
Vibration from fans and compressors
(source 1) and vibration from casingradiated noise caused by duct turbulence
and the airborne noise of the fans and
compressors (source 2) are controlled
with Kinetics high deflection, laterally
stable coil spring isolators and high
frequency neoprene noise pads.
Duct-borne noise from the supply and
return air fans (source 3) are controlled
using an aerodynamic acoustical
silencer on the supply fan and an coustical plenum on the return air side - both
with minimal pressure drop.
Breakout noise through the bottom of
the rooftop unit (source 4) is controlled
by the NOISEBLOCK STL acoustical
panel located in the floor of the ESSR.

Air Mounts
Air Vibration Isolation Mounts
Model KAM and CAM

Kinetics air mounts are pneumatic, elastomeric vibration

mounts. The CAM is available in four (4) sizes supporting
loads up to 7,500 lbs. The KAM is available in seven (7)
sizes with capacities from 500 to 22,000 lbs. per mount.
Both models are optionally available with automatic leveling
controls and custom mounting to meet your specific needs.
Typical applications include mechanical equipment and
industrial process equipment requiring low natural
frequency isolation, as well as protecting sensitive
equipment from disturbing floor-borne vibration.

Seismic Cable Restraint

Cable Restraint Kits - Models KSCU, KSWC and KSCC

Kinetics cable restraint kits are available with bulk cable or prepackaged kits with 15' cable lengths.The prepackaged
kits are up to 1/4" cable diameter and the bulk kits up to 1/2" cable diameter. These kits are designed to meet the
latest building codes and come with the necessary brackets to meet all the applicable installations in the field.

Ductwork

Piping

Equipment

Hanging Rod Stiffener Clamp - Model KHRC

Clamp is required to brace threaded rod used to suspend piping, ductwork, and/or hanging equipment in a seismic application. It is designed to
easily and securely attach steel stiffening bracing angles to the threaded
rod, using common hand tools without disassembling the hanging rod.

Seismic Restraint Isolators and Snubbers

Modular/Restraint Isolator
Model FMS - U.S. Patent No. 7,028,969

Because of the extreme design flexibility of the modular concept, Kinetics

Model FMS Isolators can be used effectively for large, heavy pieces of
equipment in highly active seismic or wind prone areas as well as for more
common applications in less active areas without financial consequence.
Ideal for equipment mounted on structural frame or concrete inertia bases.
Because of the minimal vertical travel and near constant operating height,
the FMS isolator is excellent for use on cooling towers, chillers, boilers
or other equipment where the potential for wide weight variations during
service is anticipated.

Restrained Spring Isolators

Model FLSS

Vertically restrained spring isolators designed for higher

seismic and wind forces. The housings are fabricated
to limit vertical movement of the isolated equipment
if equipment loads are reduced or if the equipment is
subjected to large external forces such as high winds or
seismic events. The housings also provide a constant
free and operating height to facilitate installation.

Restrained Spring Isolators

Model FHS

Vibration isolation with seismic and wind restraint

capabilities for mechanical equipment. Featuring
all-directional restraint with vertical limit stops, fieldinterchangeable spring coils, galvanized housing and
polyester powder coated coils and a constant free
height and operating height.

Seismic Snubbers - Model HS Series

Seismic snubbers are designed for use in locations subject to earthquakes

or other external forces which could displace vibration isolated equipment.
Rugged, heavy-duty products which have been designed to resist imposed
forces from external sources yet remain out of contact during normal operation so that vibration will not be transmitted to the building.

Seismic Restraint Mounting Brackets

Seismic Restraint Mounting Brackets
Model KSMS and KSMF
Model KSMS seismic and wind restraint
brackets are used to solid-mount equipment to the building structure. It can be
bolted or welded to the equipment, and is
attached to the structure by anchoring to
concrete or bolting to steel.
KSMS
Model KSMF seismic and wind restraint
brackets are used to solid-mount equipment to a roof curb. It can be bolted to the
equipment and the roof curb.

KSMF

Vertical Pipe Riser Isolation Guides and Anchors

Spring Riser Guide

Model KRG

Model KRG riser guide and isolator provides flexible

support for a pipe riser by allowing it to expand and
contract vertically while limiting its movement horizontally. The KRG is available with or without spring
isolation. The deflection offered is 1", 2" and 4". The
capacity range is from 35 lbs. to 23,000lbs.

Pipe Anchor
Model KPA

Model KPA pipe anchors are used to secure the position

of a vertical or horizontal riser. The anchors are selected
based on the amount of force the pipe will transfer into
the structure a specific point of attachment. Anchor
capacities range from 2,500 lbs. to 20,000 lbs. and must
be used in pairs.

Contact Us

Kinetics Noise Control Corporate Headquarters

6300 Irelan Place, Dublin, OH 43017
Phone: 1-800-959-1229
Email: sales@kineticsnoise.com

Locations
Toronto

Las Vegas

3570 Nashua Drive

Mississauga, ON
L4V 1L2
Phone: 905-670-4922

6611 Schuster Street

Las Vegas, NV 89118
Phone 702-263-6501

Hong Kong
Unit E, 9/F World Tech Centre
95 How Ming Street
Kwun Tong, Kowloon
Phone: (852) 2191 2488