Uputa Kaiser - Calc - DQ

"NORM" mode "[MODE] [MODE] [MODE] [MODE] [3]" :cancels "Fix" and "Sci" specifications.
This operation also

changes the range of the exponent display. When the results
exceed the following limits, exponent is to be displayed.
Norm 1 :- 102 > |x|, or |x| 1010
Norm 2 :- 109 > |x|, or |x| 1010
2-line display
Scientific Calculator
Owner's Manual
with
fractional, statistical,
formula memory,
equation solving
functions
Please read before using.
Safety Precautions
Be sure to read the following safety precautions before using
this calculator. Keep this manual handy for later reference.
Batteries
After removing the batteries from the calculator, put them in
a safe place where there is no danger of them getting into
the hands of small children and accidently swallowed.
Keep batteries out of the reach of children. If accidentally
swallowed, consult with a physician immediately.
Never charge batteries, try to take batteries apart, or allow
batteries to become shorted. Never expose batteries to
direct heat or dispose of them by incineration.
Misuse of batteries can cause them to leak acid that can
cause damage to nearby items and creates the possibility of
fire and personal injury.
Always make sure that a battery's positive (+) and negative
() sides are facing correctly when you load it into the
calculator.
Remove the batteries if you do not plan to use the calculator
for a long time.
Use only the type of batteries specified for this calculator in
this manual.
Disposing of the Calculator
Never dispose of the calculator by burning it. Doing so can
cause certain components to suddenly burst, creating the
danger of fire and personal injury.
The displays and illustrations (such as key markings) shown in
this Owner's Manual are for illustrative purposes only, and
may differ somewhat from the actual items they represent.
The contents of this manual are subject to change without
notice.
Handling Precautions
Be sure to press the "ON" key before using the calculator for
the first time.
Even if the calculator is operating normally, replace the
battery at least once every three years. Dead battery can leak,
causing damage to and malfunction of the calculator. Never
leave the dead battery in the calculator.
The battery that comes with this unit discharges slightly
during shipment and storage. Because of this, it may require
replacement sooner than the normal expected battery life.
Low battery power can cause memory contents to become
corrupted or lost completely. Always keep written records of
all important data.
Avoid use and storage in areas subjected to temperature
extremes. Very low temperatures can cause slow display
response,total failure of the display, and shortening of
battery life. Also avoid leaving the calculator in direct
sunlight, near a window, near a heater or anywhere else it
might become exposed to very high temperatures. Heat can
cause discoloration or deformation of the calculator's case,
and damage to internal circuitry.
Avoid use and storage in areas subjected to large amounts of
humidity and dust. Take care never to leave the calculator
where it might be splashed by water or exposed to large
amounts of humidity or dust. Such elements can damage
internal circuitry.
Never drop the calculator or otherwise subject it to strong
impact.
Never twist or bend the calculator. Avoid carrying the
calculator in the pocket of your trousers or other tight-fitting
clothing where it might be subjected to twisting or bending.
Never try to take the calculator apart.
Never press the keys of the calculator with a ball-point pen or
other pointed object.
Use a soft, dry cloth to clean the exterior of the unit. If the
calculator becomes very dirty, wipe it off with a cloth
moistened in a weak solution of water and a mild neutral
household detergent. Wring out all excess moisture before
wiping the calculator. Never use thinner, benzine or other
volatile agents to clean the calculator. Doing so can remove
printed markings and damage the case.
i
M S H A STO RCL CMPLX SD LR PAUSE D R G FIX SCI ENG
You can simultaneously check the calculation formula and its

answer. The first line displays the calculation formula. The
second line displays the answer.
Keys Layout
Mcl Scl
ALPHA
CALC
()
:
x!
d/c
a b/c
A
dx
IN
,,,
STO
A
DEC
RCL
7
4
10
x2
[b]
sin
Abs
cos
BIN
log
1
)
C
6
xn1
Rnd
Ran#
EXP
OCT
ln
[o]
tan
tan
INS
M+
DT
CL
OFF
DEL
AC
nPr
nCr
yn1
xn
xy
x
cos
sin
yn
HEX
[h]
arg
x 1
hyp
r
x3
OUT
[d]
LOGIC
i
ENG
ON
MODE
SOLVE
"Eng" mode "[MODE] [MODE] [MODE] [MODE] [MODE] [1]"

:- "ENG" symbols appears in display window when this mode is
selected.
Or you can deselect engineering display mode by pressing
"[MODE] [MODE] [MODE] [MODE] [MODE] [2]". the "ENG"
symbol will be OFF.
With the exception of the BASE-N mode, "Fix", "Sci" and
"Norm" modes can be used in combination with the manual
calculations.
Engineering display format is not available in "CMPLX" mode.
The display mode last selected is retained in memory when
the power is switched OFF.
Calculation Priority Sequence
This calculator employs true algebraic logic to calculate the
parts of a formula in the following order :1. Coordinate transformation / integration, Pol(x, y),Rec(r, ),
dx, d/dx
2. Type A functions :These functions are those in which the value is entered and
than the function key is pressed, such as x2, x1, x!, ''',
Engineering symbols.
3. Power / root, xy, x
4. Fractions, ab/c
5. Abbreviated multiplication format in front of , memory or
parenthesis, such as 2, 5A, R, etc.
6. Type B functions :These functions are those in which the function key is
pressed and then the value is entered such as , 3, log, ln, ex,
10x, sin, cos, tan, sin1, cos1, tan1, sinh, cosh, tanh, sinh1,
cosh1, tanh1, Int, Frac, Abs, (), (following in BASE-N mode
only) d, h, b, o, Neg, Not.
7. Abbreviated multiplication format in front of Type B
functions, such as, 23, A log2, etc.
8. Permutation, combination, nPr, nCr
9. ,
10. ,
11. and ( in BASE-N mode only )
12. or, xor, xnor ( in BASE-N mode only )
When functions with the same priority are used in series,
execution is performed from right to left for :- exln120
ex{ln(120)}. Otherwise, execution is from left to right.
Operations enclosed in parentheses are performed first.
Number of Stacks
There is a memory area known as a "stack" for the temporary
storage of low priority numeric values and commands (
functions, etc. ). The numeric value stack has nine levels, while
the command stack has 24. If a complex formula is employed
that exceeds the stack space available, a stack error (Stk
ERROR) message will appear on the display.
Calculations are performed in the order of the highest
calculation priority first. Once a calculation is executed, it is
cleared from the stack.
Number of Input/output Digits and Calculation Digits
The allowable input/output range (number of digits) of this
unit is 10 digits for a mantissa and 2 digits for the exponent.
Calculations, however, are performed internally with a range of
12 digits for a mantissa and 2 digits for an exponent.
Example: 3 105 7 =
[3] [EXP] [5] [] [7] [=]
[3] [EXP] [5] [] [7] []
[4] [2] [8] [5] [7] [=]
3 E 57
42857.14286
D
3 E 5742857
0.14285714
Overflow and Errors

If the operational range of the unit is exceeded, or incorrect
inputs are made, an error message will appear on the display
and subsequent operation will be impossible. This is carried
out by the error check function. The following operations will
result in errors :1. The answer, whether intermediate or final, or any value in
memory exceeds the value of 9.999999999 1099.
2. An attempt is made to perform function calculations that
exceed the input range.
3. Improper operation during statistical calculations, e.g.,
attempting to obtain x or xn without data input.
4. The capacity of the numeric value stack or the command
stack is exceeded.
5. Input errors are made, e.g. 5 3 = .
6. Improper operation with matrix, e.g. addition of two
matrices with different dimensions.
7. Not enough capacity for program storage.
When error message appears, most keys will become
inoperative. In this case, press the [AC] key to return to normal
operation. You can also press the [] or [] key to cause the
cursor to show the position of the error.
The following error messages will be displayed for the
operations listed above:case (1) to case (3)
Ma ERROR
case (4)
Stk ERROR
case (5)
Syn ERROR
case (6)
Dim ERROR
case (7)
Mem ERROR
Besides pressing [AC] when an error occurs, you can also press
[ON] key to clear the error.
Two-lines Display
SHIFT
In combination with "Fix", "Sci" or "Norm" mode, you can cause

the exponent display for the number being displayed to
change in multiples of 3 by selecting engineering display
mode in the sub-menu.
Pol(
+
DRG
Ans
[3]
122_
122
123_
Example: To change an input of cos60 to sin60 :[cos] [6] [0]

[] [] []
CMPLX
2
Press [MODE] again.
REG BASE
2
3
Press [MODE] again.

(This sub-menu will be skipped in Base-n mode.)
Deg Rad Gra

1
2
3
Press [MODE] further.
(This sub-menu will be skipped in Base-n mode.)
Fix Sci Norm

1
2
3
Press [MODE] again. (This sub-menu will be skipped in both
Complex mode and Base-n mode.)
EngOFF
2
Press "MODE" once more to leave the menu.
[sin]
Note: The five calculation modes listed above are totally

independent, and cannot be used together.
The calculation mode last selected is retained in memory
when the power is switched OFF.
Angular Measurement Modes
"DEG" mode "[MODE] [MODE] [MODE] [1]" :- specify
measurement in "degrees". "D" symbol appears in display
window.
"RAD" mode "[MODE] [MODE] [MODE] [2]" :- specify
measurement in "radians". "R" symbol appears in display
window.
"GRA" mode "[MODE] [MODE] [MODE] [3]" :- specify
measurement in "grads". "G" symbol appears in display
window.
With the exception of the BASE-N mode, these three angular
measurement modes can be used in combination with the
manual calculation modes.
Display Modes
"FIX" mode "[MODE] [MODE] [MODE] [MODE] [1]" :- specify
number of decimal places. "Fix" symbol appears in display
window.
"SCI" mode "[MODE] [MODE] [MODE] [MODE] [2]" :- specify
number of significant digits. "Sci" symbol appears in display
window.
Operation
23 [] 4.5 [] 53 [=]
25.5
56[][()]12[][()]2.5[=]
268.8
12369[] 7532 []
74103[=]
6.90368061312
4.5[EXP]75 [] [()]2.3
[EXP] [()]79 [=]
1.03503
[( ] 2 [] 3[ )][] 1
[EXP]2 [=]
500.
1[EXP]5 [] 7 [=]
(1105)7=
14285.71429
14285.71429
1[EXP]5[]7 []
(1105)714285=
14285 [=]
0.7142857
0.71428571
please note that internal calculation is calculated
in 12 digits for a mantissa and the result is
displayed and rounded off to 10 digits.
3 [] 5 [] 6 [=]
3 + 5 6 = 33
33.
7 [] 8 [] 4 [] 5 [=]
7 8 4 5 = 36
36.
1 2 3 4 5 6 1 [] 2 [] 3 [] 4 []
5 [] 6 [=]
= 6.6
6.6
100 (23) 4 = 80 100 [][( ] 2 [] 3[ )]
[] 4 [=]
80.
2 [] 3 [] [(] 4 [] 5 [=]
2 3 ( 4 5 ) = 29
29.
Closed parentheses
occurring immediately
before operation of the
[=] key may be omitted.
( 7 2 ) ( 8 5 ) = 65 [( ] 7 [] 2 [ )][( ] 8 [] 5 [=]
65.
A multiplication sign []
occurring immediately
before an open parantheses
can be omitted.
10 { 2 7 ( 3 6 )} 10 [][( ] 2 [] 7 [( ] 3 []
55.
= 55
6 [=]
23 + 4.5 53 =25.5
56(12)(2.5)=268.8
12369753274103=
6.9036806131012
(4.51075)(2.3
1079) = 1.035103
(2+3)102=500
Specifying the Format of Calculation Results

You can change the precision of calculation results by
specifying the number of decimal places or the number of
significant digits. You can also shift the decimal place of a
displayed value three places to the left or right for one-touch
conversions of metric weights and measures.
Upon power up reset, the display format is defaulted at
"Norm1". Each time you can press "[MODE] [MODE] [MODE]
[MODE] [3]" you can choose either "Norm 1" or "Norm 2" by
keying in [1] or [2] respectively.
Norm 1 :- all values less than 102 or greater than 109 are
automatically expressed as exponents.
Norm 2 :- all values less than 109 or greater than 109 are
automatically expressed as exponents.
Note: You cannot specify the display format (Fix, Sci) while the
calculator is in Base-N mode.
Specifying the Number of Decimal Places
The calculator always performs calculations using a 10-digit
mantissa and 2-digit exponent, and results are stored in
memory as a 12-digit mantissa and 2-digit exponent no matter
how many decimal places you specify. Intermediate results
and final results are then automatically rounded off to the
number of decimal places you have specified.
It should be noted that displayed results are rounded to
the specified number of decimal places, but stored results
are normally not rounded.
To specify the number of decimal places ( Fix ), press "[MODE]
[MODE] [MODE] [MODE] [1]" and then a value indicating the
number of places (0~9). At this time, you should be able to see
"Fix" on the display. The number of decimal places specified
will remain in effect until Norm1 or Norm2 is specified as
described above or significant digits are specified using
"[MODE] [MODE] [MODE] [MODE] [2]".
Example
cos 60
sin 60
Operation
1006 = 16.66666666 100 [] 6 [=]

16.66666667
specify 4 decimal places [Mode][Mode][Mode][Mode]
[1][4]
16.6667
[Mode][Mode][Mode][Mode]
cancel specification
[3][1]
16.66666667
200[]7 [] 14[=]
400.
200714 = 400
rounded to 3 decimal [Mode][Mode][Mode][Mode]
[1][3]
places
400.000
200 [] 7[=]
28.571
The intermediate result is
automatically rounded
to the specified three
decimal places.
[]
Ans
The stored 10-digit
(upper display)
result (28.571421857) is
used when you continue
the calculation by simply
pressing [] or any other
arithmetic function key.
14[=]
400.000
(The final result is
decimal places.)
Cancel specification.
400.
[3][1]
Rounding the Intermediate Result

As the number of decimal places is specified, the intermediate
result will be automatically rounded to the specified decimal
places. However, the stored intermediate result is not rounded.
In order to match the displayed value and the stored value,
[SHIFT] [RND] can be input.
You can compare the final result obtained in the previous
example with the final result of the following example.
Example
Example: To correct an input of 369 2 to 369 2 :[3] [6] [9] [] [] [2]

[] [] [DEL]
369x2
If a character has been omitted from a formula, use the ""

and "" key to move to the position where the character
should have been input, and press [SHIFT] followed by [INS]
key. Each press of [SHIFT] [INS] will create a space for input of
one command.
Example: To correct an input of 2.362 to sin 2.362 :[2] [] [3] [6] [x2]
2
[SHIFT][INS]
[sin]
2.36 _
2.36 2
.36 2
sin .36 2
Operation
200714 = 400
rounded to 3 decimal
places
Percentage Calculations
Percentage cannot be executed in Base-N mode or CMPLX
mode.
Percentage
26% of $15.00
Premium
15% increase from
$36.20
Discount
4% discount from
$47.50
Ratio
75 is what % of 250?
Rate of change
141 is an increase of
what % from 120?
Rate of change
240 is a decrease of
what % from 300?
15 []26 [SHIFT] [%]

36.2[]15 [SHIFT] [%] []
47.5[]4 [SHIFT] [%] []
75[]250 [SHIFT] [%]
141[]120 [SHIFT] [%]
240[]300 [SHIFT] [%]
28.571
28.571
Example
14 [=]
[3][1]
Ans
(upper display)
399.994
399.994
Display
(Lower)
Operation
1006 = 16.66666666
specify 5 significant
digits
100[]6 [=]
[2][5]
[3][1]
16.66666667
1.666701
16.66666667
Shifting the Decimal Place

You can use the key [ENG] to shift the decimal point of the
displayed value three places to the left or right. Each 3-place
shift to the left is the same as dividing the value by 1000, and
each shift to the right is the same as multiplying by 1000. This
means that this function is useful when converting metric
weights and measures to other metric units.
Example
Display
(Lower)
Operation
123m456 = 56088m
= 56.088km
78g0.96 = 74.88g
= 0.07488kg
Display
(Lower)
3.9
123[]456 [=]
[ENG]
78[]0.96 [=]
[SHIFT] [ENG]
56088.
56.08803
74.88
0.0748803
41.63
45.6
30.
17.5
20.
Mcl Prog
1
2
Mcl_
Then proceed to memory clear by pressing [=].
Contents of both the variable and independent memories are
protected even when the power is turned OFF.
Variable memories
Up to 9 values can be retained in memory at the same time,
and can be recalled when desired.
Example: Input 123 into memory "A" :[AC] [1] [2] [3]
123_
[AC]
[RCL] [A]
[AC]
[RCL] [B]
B=
_
B=
AxB_
[STO] [C]
C=
[AC]
[RCL] [C]
C=
A=log2 _
[] [7] [] [1]
12x3.587.1 _
[=]
4.12x3.587.
7.6496
[RCL] [A]
A=log2
0.301029995.
A=
_
A=
123.
When formulas are input, the result of the formula's calculation

is retained in memory.
Example: Input the result of 123456 into memory "B" :[AC] [1] [2] [3] [] [4] [5] [6]
123x456_
The replay function is not cleared even when [AC] is pressed or

when power is turned OFF, so contents can be recalled even
after [AC] is pressed.
Replay function is cleared when mode or operation is
switched.
Error Position Display Function
When an ERROR message appears during operation
execution, the error can be cleared by pressing the [AC] key,
and the values or formula can be re-entered from the
beginning. However, by pressing the [] or [] key, the
ERROR message is cancelled and the cursor moves to the point
where the error was generated.
Example: 1402.3 is input by mistake
[AC] [1] [4] [] [0] []
[2] [.] [3] [=]
[] (or [] )
Example: Input 123 to independent memory.

[AC] [1] [2] [3]
_
123
123
123.
_
M=
123.
12
12.
Correct the input by pressing

[] [SHIFT] [INS] [1]
[=]
M=
Difference between [STO][M] and [M+], [Shift][M] :Both [STO] [M] and [M+], [Shift] [M] can be used to input
results into memory, however when the [STO] [M] operation is
used, previous memory contents are cleared. When either
[M+] or [Shift] [M] is used, value is added or subtracted to or
from present sum in memory.
Example: Input 456 into memory "M" using [STO] [M]
procedure. Memory already contains value of 123.
[AC] [1] [2] [3] [STO] [M]
A 3.2
456.
[RCL] [M]
Disp
848.7
[AC] [4] [5] [6] [M+]
456
38.4375
[=]
5x6
[sin] [Ans]
sin Ans _
[=]
sin Ans
Disp
30.
Disp
Disp
0.5
When interrupt operation is completed, press [=] once again to

execute.
7x8
[=]
Scientific Function
456.
123.
D
456.
[AC]
[RCL] [M]
M=
579.
Special Functions
Answer Function
This unit has an answer function that stores the result of the
most recent calculation. Once a numeric value or numeric
expression is entered and [=] is pressed, the result is stored by
this function.
To recall the stored value, press the [Ans] key. When [Ans] is
pressed, "Ans" will appear on the display, and the value can be
used in subsequent calculations.
[AC][1][2][3][][4][5][6][=]
123+456
579.
[7][8][9][][Ans]
789-Ans _
[=]
789-Ans
210.
Numeric values with 12 digits for a mantissa and 2 digits for an

exponent can be stored in the "Ans" memory. The "Ans"
memory is not erased even if the power of the unit is turned
OFF. Each time [=] , [Shift] [%] , [M+] , [Shift] [M] , and [STO]
( = A ~ F, M, X, Y ) is pressed, the value in the Ans memory is
replaced with the new value produced by the calculation
execution. When execution of a calculation results in an error,
however, the "Ans" memory retains its current value.
Note:- Contents of "Ans" memory are not altered when RCL
( = A~F, M, X, Y) is used to recall contents of variable memory.
Also, contents of "Ans" memory are not altered when variables
are input when the variable input prompt is displayed.
Omitting the multiplication sign ()
When inputting a formula as it is written, from left to right, it is
possible to omit the multiplication sign () in the following
cases : Before the following functions :sin, cos, tan, sin1, cos1, tan1, sinh, cosh, tanh, sinh1, cosh1,
tanh1, log, ln, 10x, ex, , 3, Pol(x,y), Rec(r, )
example: 2sin30, 10log1.2, 23, 2Pol(5, 12), etc.
Before fixed numbers, variales and memories :example: 2, 2AB, 3Ans, etc.
Before parentheses :example: 3(56), (A1)(B1), etc.
Continuous Calculation Function
Even if calculations are concluded with the [=] key, the result
obtained can be used for further calculations. In this case,
calculations are performed with 10 digits for the mantissa
which is displayed.
Example: To calculate 3.14 continuing after 34=12
[AC] [3] [] [4] [=]
3x4
12.
(continuing) [] [3] [] [1] [4]
Ans 3.14 _
[=]
Ans 3.14
3.821656051
Example: To calculate 133 =

[AC] [1] [] [3] [] [3] [=]
[1] [] [3] [=]
1 3x3
1.
D
1 3
0.333333333
D
Ansx3
0.999999999
This function can be used with Type A functions ( x2, x1, x!), ,
, xy, x and ' ".
Example: Squaring the result of 786=13
[AC] [7] [8] [] [6] [=]
78 6
(continuing) [x2]
Ans 2 _
[=]
78 6
13.
13.
Replay Function
This function stores formulas that have been executed. After
execution is complete, pressing either the [] or [] key will
display the formula executed.
Pressing [] will display the formula from the beginning, with
the cursor located under the first character.
Pressing [] will display the formula from the end, with the
cursor located at the space following the last character. After
this, using the [] and [] to move the cursor, the formula can
be checked and numeric values or commands can be changed
for subsequent execution.
Example:
[AC] [1] [2] [3] [] [4] [5] [6] [=]
360.
10[SHIFT][nCr]4[=]
210.
25[SHIFT][nCr]5[]15
[SHIFT][nCr]5[=]
50127.
Random number
generation (number is
in the range of 0.000 to
0.999)
(1sin240)
= 0.766044443
1/2!1/4!1/6!1/8!
= 0.543080357
Display
(Lower)
Operation
[]2[][]5[=]
2[x2][]3[x2][]4[x2]
[]5[x2][=]
[(][]3[)][x2][=]
[(]3[SHIFT][x1][]4[SHIFT]
[x1][)][SHIFT][x1][=]
8[SHIFT][x!][=]
[SHIFT][3][(]36[]42[]
49[)][=]
[SHIFT][Ran#][=]
[MODE][MODE][MODE][1]("DEG")
[][(]1[][(][sin]40[)][x2]
[)][=]
[SHIFT][cos1][Ans][=]
2[SHIFT][x!][SHIFT][x1][]
8[SHIFT][x!][SHIFT][x1][=]
3.65028154
54.
9.
12.
40320.
42.
0.792
(random)
0.766044443
40.
0.543080357
Fractions
Fractions are input and displayed in the order of integer,
numerator and denominator.
Display
(Lower)
Operation
2[ab/c]5[]3[ab/c]1
[ab/c]4[=]
31320.
[ab/c] (conversion to decimal)
3.65
Fractions can be converted
to decimals, and then
converted back to fractions.
81113.
3456/78 = 811/13
3[ab/c]456[ab/c]78[=]
[SHIFT][d/c]
11513.
1/25781/4572
1[ab/c]2578[]1[ab/c]
4572[=]
= 6.066202547104
6.06620254704
When the total number
of characters, including
integer, numerator,
denominator and
delimiter mark exceeds
10, the input fraction is
automatically displayed
in decimal format.
1/20.5 = 0.25
1[ab/c]2[].5[=]
0.25
1/3(4/5)5/6 = 11/10 1[ab/c]3[][]4[ab/c]5
b
[]5[a /c]6[=]
1110.
1/21/31/41/5
1[ab/c]2[]1[ab/c]3[]
1[ab/c]4[]1[ab/c]5[=]
= 13/60
1360.
[(]1[ab/c]2[)][ab/c]3[=]
16.
(1/2)/3 = 1/6
1/(1/31/4) = 15/7
b
b
1[a /c][(]1[a /c]3[]
b
1[a /c]4[)][=]
157.
Example: Input 456 into memory "M" using M+. Memory

already contains value of 123.
[AC] [1] [2] [3] [STO] [M]
M=
7[SHIFT][nPr]4[]3[]
7[=]
2/531/4 = 313/20
56.
M=
8! = 40320
3(364249) = 42
Example
(3)2 = 9
1/(1/31/4) = 12
Even if "" is not input at the end of a formula, the final result
will be displayed.
Consecutive calculations containing multistatements cannot
be performed.
123 456 : 5
invalid
Calculations can be performed while an intermediate result is
displayed during execution interrupted by "".
Example: 56 78
[AC] [5] [] [6] [ALPHA] []
5x6 7x8 _
[7] [] [8]
123.
[AC]
Multistatement Function
The multistatement function (using colons to separate
formulas or statements) available in program calculations
can also be used for manual calculations.
The multistatement function allows formulas to be separated
by colons ( [ALPHA] [:] ) to make consecutive, multiple
statement calculations possible.
When [=] is pressed to execute a formula input using the
multistatement format, the formula is executed in order from
the beginning.
Inputting "" ( [ALPHA] [] ) in place of the colon will
display the calculation result up to that point during
execution.
136.
Addition/subtraction to or from sum in memory cannot be

carried out with [M+], [Shift] [M] keys in SD mode and REG
mode.
M=
25 = 3.65028154
22324252 = 54
14 10x2.3
"Disp" appears on the display when "" is used.
To clear memory contents, press [0] [STO] [M].
M=
Example
6.9xA
5040.
10[SHIFT][nPr]4[=]
Other Functions ( , x2, x1, x!, 3, Ran#)

The following operations is invalid in the BASE-N mode. When
in the BASE-N mode, carry out calculation after going back to
"COMP" mode.
14 10x2.3
3.22
Example:
6.9123 = 848.7
1233.2 = 38.4375
[AC]123 [STO] [A] 6.9 []
[ALPHA] [A] [ALPHA] []
[ALPHA] [A] [] 3.2 [=]
Taking any four out of

ten items and arranging
them in a row, how many
different arrangements
are possible?
10P4 = 5040
Using any four numbers
from 1 to 7, how many
four digit even numbers
can be formed if none of
the four digits consist of
the same number?
(3/7 of the total number
of permutations will be
even.)
7P437 = 360
If any four items are
removed from a total
of 10 items, how many
different combinations
of four items are
possible?
10C4 = 210
If 5 class officers are
being selected for a
class of 15 boys and
10 girls, how many
combinations are
possible? At least one
girl must be included
in each group.
25C515C5 = 50127
Display
(Lower)
Operation
Ma ERROR
14 0x2.3 _
[=]
123.
Independent Memory
Addition and subtraction (to and from sum) results can be
stored directly in memory. Results can also be totalized in
memory, making it easy to calculate sums. The icon "M" will be
lighted as long as M is not empty.
[AC] [4] [5] [6] [STO] [M]
Deleting memories
To delete all contents of variable memories, press [Shift] [CLR]
[1] [=].
[RCL] [M]
4.12x3.58+6.
21.1496
D
6898824.
The following operation is invalid in the BASE-N mode. When

in the BASE-N mode, carry out calculation after going back to
"COMP" mode ([MODE] [1]).
Example
4.12x3.58+6.
Recall memory data

[AC]
Example:
4.123.586.4 = 21.1496
4.123.587.1 = 7.6496
[AC] [4] [] [1] [2] []
[3] [] [5] [8] [] [6] [] [4] [=]
[] [] [] []
[AC]
Add 25, subtract 12

[2] [5] [M+] [1] [2] [SHIFT] [M]
123x456 _
6898824.
A=log2
0.301029995.
[RCL] [M]
[]
12x3.58+6.4 _
[=]
Recall memory data

[AC]
123x456
56088.
[]
When input is made in a format such as "A=log 2", where the

variable is equal to the formula, the results of the calculation
are input into the specified memory.
[M+]
[=]
56088.
Syn ERROR is generated when an attempt is made to input a

substitution formula (such as C = AB) or multistatements
(such as AB : CD), and the existing memory contents are
retained.
Example: Executing "A=log2" :[AC] [ALPHA] [A] [ALPHA] [=]

[log] [2]
123x456
56088.
Example: Input the results of AB into memory "C" :[AC] [ALPHA] [A] [] [ALPHA] [B]
Permutation and Combination

Total number of permutations nPr = n!/(nr)!
Total number of combinations nCr = n!/(r!(nr)!)
[]
56088.
If a variable expression is entered, the expression is first

calculated according to the values stored in the variable
memories used in the expression. The result is then stored in
the variable memory specified for the result.
(continuing) [] [3] [=]
Press [1] to select the command "Mcl".
[STO] [A]
[STO] [B]
Example: 123456 = 579

789579 = 210
[]
400.
400.000
When you want to clear all the memories (except independent

memory M), you can press [SHIFT][CLR] to view the CLR menu
in which "Mcl" and "Prog" are displayed.
Even after the [=] key has been pressed to calculate a result, it
is possible to use this procedure for correction. Press the []
key to move the cursor to the place where the correction is to
be made.
Operation
round the stored

intermediate result to
the specified three
decimal places
200[]7 [] 14[=]
[1][3]
200[]7 [=]
The intermediate result is
decimal places.
[SHIFT] [RND]
Memory
This calculator contains 9 standard memories. There are two
basic types of memories, i.e., "variable" memories, which are
accessed by using the [STO] and [RCL] keys in combination
with the alphabets A, B, C, D, E, F, M, X and Y. The "independent"
memories, which are accessed by using the [M+] , [Shift] [M]
and [RCL] and [M] keys. The variable memory and
independent memory utilize the same memory area.
When [SHIFT] [INS] are pressed, the space that is opened is

". The function or value assigned to the next
displayed as "
key you press will be inserted in the . To exit from the
insertion mode, move the cursors, or press [SHIFT] [INS], or
press [=].
Example
Display
(Lower)
To specify the number of significant digits (Sci.), press

"[MODE] [MODE] [MODE] [MODE] [2]" and then a value
indicating the number of significant digits (0~9) to set from 1
to 10 digits with "0" indicating 10 digits. The "Sci" indicator will
appear on the display.
If an unnecessary character has been included in a formula,

use the [] and [] keys to move to the position of the error
and press the DEL key. Each press of DEL will delete one
command ( one step ).
369xx2_
Display
(Lower)
As with the number of decimal places, displayed results are

rounded to the specified number of digits, but stored results
are normally not rounded.
If after making corrections, input of the formula is complete,

the answer can be obtained by pressing [=]. If, however, more
is to be added to the formula, advance the cursor using the
[] key to the end of the formula for input.
[] [] [] [] []
Calculation Modes
"COMP" mode "[MODE] [1]" : - general calculations, including
function calculations can be executed.
"CMPLX" mode "[MODE] [2]" :- calculations including
complex numbers can be executed.
"SD" mode "[MODE] [MODE] [1]" :- standard deviation
calculation can be executed. "SD" symbol appears in display.
"REG" mode "[MODE] [MODE] [2]" :- regression calculations
can be performed. "REG" symbol appears in display.
"BASE-N" mode "[MODE] [MODE] [3]" :- binary, octal, decimal,
hexadecimal conversion and calculations, as well as logical
operations can be carried out.
cos 60
Display
(Lower)
Specifying the Number of Significant Digits

This specification is used to automatically round intermediate
results and final results to the number of digits you have
specified.
Im
Press [MODE] once to read the first page of the main menu.
EngON
1
Corrections
To make corrections in a formula that is being input, use the
[] and [] keys to move to the position of the error and
press the correct keys.
Example: To change an input of 122 to 123 :[1] [2] [2]
Rec(
Operation Modes
When using this calculator, it is necessary to select the proper
mode to meet your requirements. This can be done by
pressing [MODE] to scroll through sub-menus. Then select the
appropriate mode by keying in the number.
SD
1
When numeric values or calculation commands are input, they

appear on the display from the left. Calculation results,
however, are displayed from the right.
% Re
Example
Input characters are limited to 79 steps. Usually, the cursor is

represented by a blinking " _ ".
[]
Before Starting Calculations
COMP
1
Number of Input Characters

This calculator features a 79-step area for calculation
execution. One function comprises one step. Each press of
numeric or , , and keys comprise one step.
Though such operations as [SHIFT] [x!] (SOLVE key) require
two key operations, they actually comprise only one function,
and, therefore, only one step. These steps can be confirmed
using the cursor. With each press of the [] or [] key, the
cursor is moved one step.
Arithmetic Operations & Parenthesis Calculations

Arithmetic operations are performed by pressing the keys in
the same order as noted in the formula.
For negative values, press [(-)] before entering the value
For mixed basic arithmetic operations, multiplication and
division are given priority over addition and subtraction
Assuming that display mode Norm is selected.
123x456
56088.
Trigonometric functions and inverse trigonometric

functions
Be sure to set the unit of angular measurement before
performing trigonometric
function and inverse
trigonometric function calculations.
The unit of angular measurement (degrees, radians, grads) is
selected in sub-menu.
Once a unit of angular measurement is set, it remains in effect
until a new unit is set. Settings are not cleared when power
is switched OFF.
This operation is invalid in the "BASE-N" mode. When in the
"BASE-N" mode, go back to COMP mode by selecting
"COMP" in the main menu.
Example
sin 6352'41"
= 0.897859012
cos (/3 rad) = 0.5
tan (35 grad)
= 0.612800788
Operation
[sin] 63 [ ' "] 52 [ ' "]
41 [ ' "][=]
[MODE][MODE][MODE][2]("RAD")
[cos][(] [SHIFT][][]3
[)] [=]
[MODE][MODE][MODE][3]
Display
(Lower)
0.897859012
0.5
("GRA" selected)
0.612800788
[tan] [] 35 [=]
2[sin] 45 [cos] 65 [=]
0.597672477
[SHIFT][sin1] 0.5 [=]
30.
[SHIFT][cos1][(][]2 []2
0.785398163
[)][=]
0.25
[][SHIFT][][=]
1
tan 0.741
1
36.53844577
= 36.53844577
[SHIFT][tan ]0.741[=]
363218.4
= 3632' 18.4"
[SHIFT] [' "]
If the total number of digits for degrees/minutes/seconds exceed
11 digits, the higher order values are given display priority, and
any lower-order values are not displayed. However, the entire
value is stored within the unit as a decimal value.
2.5(sin10.8cos10.9) 2.5[] [(] [SHIFT] [sin1]0.8
= 6813'13.53"
[] [SHIFT] [cos1] 0.9 [)]
681313.53
[=] [SHIFT] [' "]
2sin45cos65
= 0.597672477
sin1 0.5 = 30
cos1 (2/2)
= 0.785398163 rad
= /4 rad
Logarithmic and Exponential Functions

in the BASE-N mode, carry out calculation after selecting
"COMP" mode([MODE] [1]).
Example
log1.23
= 8.9905111102
In90 = 4.49980967
log456In456
= 0.434294481
101.23 = 16.98243652
e4.5 = 90.0171313
104 e41.2 102.3
= 422.5878667
(3)4 = 81
34 = 81
5.62.3 = 52.58143837
7123 = 1.988647795
(7823)12
= 1.3051118291021
233644 = 10
(5+6.7)
23.4
= 3306232
Operation
Display
(Lower)
sinh3.6= 18.28545536
cosh1.23 = 1.856761057
tanh2.5= 0.986614298
cosh1.5sinh1.5
= 0.22313016
sinh1 30 = 4.094622224
cosh1 (20/15)
= 0.795365461
x = (tanh1 0.88) / 4
= 0.343941914
sinh1 2cosh11.5
= 1.389388923
sinh1 (2/3)tanh1(4/5)
= 1.723757406
[In] 90 [=]
[log]456[In]456 [=]
0.089905111
4.49980967
0.434294481
16.98243652
[SHIFT][10x] 1.23 [=]
90.0171313
[SHIFT][ex]4.5[=]
[SHIFT][10x]4[][SHIFT][ex]
[]4[]1.2[][SHIFT][10x]
422.5878667
2.3[=]
81.
[(][] 3 [)] [xy] 4 [=]
y
81.
[] 3 [x ] 4 [=]
52.58143837
5.6 [xy] 2.3 [=]
1.988647795
7 [SHIFT][x] 123 [=]
[(]78[]23[)][xy][]12[=] 1.30511182921
2[]3[]3[SHIFT][x]64
[]4[=]
2[]3.4[xy][(]5[]6.7[)][=]
10.
3306232.001
Operation
[hyp][sin] 3.6 [=]
[hyp][cos] 1.23 [=]
[hyp][tan] 2.5 [=]
[hyp][cos] 1.5 [][hyp]
[sin] 1.5 [=]
[hyp][SHIFT][sin1] 30 [=]
[hyp][SHIFT][cos1][(] 20
[] 15 [)][=]
[hyp][SHIFT][tan1]0.88
[]4[=]
[hyp][SHIFT][sin1]2[]
[hyp][SHIFT][cos1]1.5[=]
[hyp][SHIFT][sin1][(]2[]
3[)][][hyp][SHIFT][tan1]
[(]4[]5[)][=]
Display
(Lower)
18.28545536
1.856761057
0.986614298
0.22313016
4.094622224
0.795365461
0.343941914
1.389388923
1.723757406
Coordinate Transformation
This scientific calculator lets you convert between rectangular
coordinates and polar coordinates, i.e., P(x, y) P(r, )
Calculation results are stored in variable memory E and
variable memory F. Contents of variable memory E are
displayed initially. To display contents of memory F, press
[RCL] [F].
With polar coordinates, can be calculated within a range of
180< 180.
(Calculated range is the same with radians or grads.)
The following operation is invalid in the BASE-N mode. Before
carry out calculation, one should switch back to "COMP"
mode ([MODE] [1]).
Example
x=14 and y=20.7, what
are r and ?
x=7.5 and y=10, what
are r and rad?
r=25 and = 56, what
are x and y?
r=4.5 and =2/3 rad,
what are x and y?
Operation
[SHIFT] [k] (#key 6)
[SHIFT] [M] (#key 7)
[SHIFT] [G] (#key 8)
[SHIFT] [ T ] (#key 9)
[SHIFT] [m] (#key 5)
[SHIFT] [] (#key 4)
[SHIFT] [n] (#key 3)
[SHIFT] [p] (#key 2)
[SHIFT] [F] (#key 1)
Example
Unit
Unit Symbol
103
106
109
1012
103
106
109
1012
1015
K (kilo)
M (mega)
G (giga)
T (tera)
m (milli)
(micro)
n (nano)
p (pico)
f (femto)
Operation
Display
999k (kilo) 25k (kilo)

= 1.024M (mega)
[Mode][Mode][Mode]
[Mode][Mode][1] ("EngON")
999 [SHIFT][k][]
25 [SHIFT][k][=]
100m (milli)5 (micro) 100[SHIFT][m][]
= 500n (nano)
5[SHIFT][][=]
910 = 0.9
9[]10[=]
= 900m (milli)
[SHIFT][ENG]
[ENG]
1.024M
500.n
900.m
0.9
900.m
Degrees, Minutes, Seconds Calculations

You can perform sexagesimal calculations using degrees
(hours), minutes and seconds. And convert between
sexagesimal and decimal values.
Example
Operation
Display
21528.8
To express 2.258 degrees 2.258[' "][=]

in deg/min/sec.
To perform the calculation: 12[' "]34[' "]56[' "][]
1234'56"3.45
3.45[=]
432431.2
Degree, Radian, Gradient Interconversion

Degree, radian and gradient can be converted to each other
with the use of [SHIFT][DRG>].
Example
Define degree first
Change 20 radian to
degree
To perform the following
calculation :10 radians+25.5 gradients
The answer is expressed
in degree.
Operation
Display
20[SHIFT][DRG>][2][=]
10[SHIFT][DRG>][2]
[]25.5[SHIFT][DRG>][3]
[=]
20r
1145.91559
10r25.5g
595.9077951
[log] 1.23 [=]
Performing Hyperbolic and Inverse Hyperbolic Functions

the user is in the BASE-N mode, he/she should go back to
"COMP" mode ([MODE] [1]) before carrying out calculation.
Example
Engineering Symbol Calculations

This unit allows engineering calculations utilizing engineering
symbols.
The Eng mode is specified by pressing [MODE] [MODE]
[MODE] [MODE] [MODE] [1] in COMP mode, LR mode, and SD
mode ("ENG" symbol appears on display). To exit from this
mode, press [MODE] [MODE] [MODE] [MODE] [MODE] [2].
Operation
[SHIFT][Pol(]14 [,]20.7[)][=]
[RCL][F][SHIFT][' "]
[SHIFT][Pol(]7.5[,][]10[)][=]
[RCL][F]
[SHIFT][Rec(]25 [,]56[)][=]
[RCL][F]
[SHIFT][Rec(]4.5[,][(]2[]
3[][SHIFT][][)][)][=]
[RCL][F]
Display
(Lower)
24.98979792(r)
555542.2()
Scientific Constants
A total of 40 commonly used scientific constants, such as the
speed of light in a vaccum and Planck's constant are built-in for
quick and easy look-up. Simply input the number that
corresponds to the scientific constant (see the table below for a
complete list of available constants) you want to look-up and it
appears instantly on the display.
To select this constant
Input this number
proton mass (mp)

neutron mass (mn)
electron mass (me)
muon mass (m)
Bohr radius (a0)
Planck constant (h)
nuclear magneton (N)
Bohr magneton (B)
Planck constant, rationalized (h)
fine structure constant ()
classical electron radius (re)
Compton wavelenght (c)
proton gyromagnetic ratio (p)
proton Compton wavelength (cp)
neutron Compton wavelength (cn)
Rydberg constant (R)
atomic mass unit (u)
proton magnetic moment (p)
electron magnetic moment (e)
neutron magnetic moment (n)
muon magnetic moment ()
Faraday constant (F)
elementary charge (e)
Avogadro constant (NA)
Boltzmann constant (k)
molar volume of ideal gas (Vm)
molar gas constant (R)
speed of light in vaccum (C0)
first radiation constant (C1)
second radiation constant (C2)
Stefan-Boltzmann constant ()
electric constant (0)
magnetic constant (0)
magnetic flux quantum (0)
standard acceleration of gravity (g)
conductance quantum (G0)
characteristic impedance of vaccum (Z0)
Celsius temperature (t)
Newtonian constant of gravitation (G)
standard atmosphere (atm)
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Example: To determine how much total energy a person

weighing 65kg has (E = mc2 = 5.8419086621018)
[6] [5]
[SHIFT] [CONST]
enter the corresponding number
[2] [8]
65_
CONST__
CONST28
12.5(r)
0.927295218()
[=]
65C0
13.97982259(x)
20.72593931(y)
[x2]
6 5 C 02
[=]
6 5 C 02
5.84190866218
2.25(x)
3.897114317(y)
Metric Conversion
A total of 20 different conversion pairs are bulit-in to provide
quick and easy conversion to and from metric units. For details,
please refer to the following table.
Number
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
Conversion
incm
cmin
ftm
mft
ydm
myd
milekm
kmmile
n milem
mn mile
acrem2
m2acre
gal (US) l
l gal (US)
gal (UK) l
l gal (UK)
pckm
kmpc
km/hm/s
m/skm/h
Number
Conversion
ozg
goz
lbkg
kglb
atmpa
paatm
mmHgPa
PammHg
hpkW
kWhp
kgf/cm2Pa
Pakgf/cm2
kgfm J
J kgfm
lbf/in2kPa
kPalbf/in2
FC
CF
Jcal
calJ
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Example: To convert 31 inches to centimeters

Key in [3] [1] [CONV]
C ON V _ _
Input the conversion number 01

[0] [1] [=]
[=]
Performing calculations
The following procedures are used to perform the various
standard deviation calculations.
Key operation
Result
3 1i n c m
Standard deviation and mean calculations are performed as

shown below:
Population standard deviation n = ((xix)2/n)
where i = 1 to n
Sample standard deviation n1 = ((xix)2/(n-1))
where i = 1 to n
Mean x = (x)/n
78.74
Example
Binary, Octal, Decimal, Hexadecimal Calculations

Binary, octal, decimal, hexadecimal calculations, conversions
and logical operations are performed in BASE-N mode (press
[MODE] [MODE] [3])
The number system (2, 8, 10, 16) is set by pressing [BIN],
[OCT], [DEC], [HEX] respectively. A corresponding symbol
"b", "o", "d" or "H" appears on the display.
Number systems are specified for specific values by pressing
the numbers system designator (BIN, OCT, DEC, HEX),
immediately followed by the value.
General function calculations cannot be performed in the
BASE-N mode.
Only integers can be handled in the BASE-N mode. If a
calculation produces a result that includes a decimal value,
the decimal portion is cut off.
If values not valid for the particular number system are used,
an error message will appear.
Number system
Valid values
Binary
Octal
Decimal
Hexadecimal
0,1
0,1,2,3,4,5,6,7
0,1,2,3,4,5,6,7,8,9
0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F
Population standard deviation, xn

Sample standard deviation, xn1
Mean, x
Sum of square of data, x2
Sum of data, x
Number of data, n
[SHIFT][xn]
[SHIFT][xn1]
[SHIFT][x]
[RCL][A]
[RCL][B]
[RCL][C]
3 1i n c m _
Deleting input data

There are various ways to delete value data, depending on
how and where it was entered.
Example 1 40 [DT] 20 [DT] 30 [DT] 50 [DT]
To delete 50, press [SHIFT] [CL] (= M+ key).
Example 2 40 [DT] 20 [DT] 30 [DT] 50 [DT]
To delete 20, press 20 [SHIFT] [CL].
Example 3 30 [DT] 50 [DT] 120 [SHIFT] [;]
To delete 120 [SHIFT] [;] , press [AC].
Example 4 30 [DT] 50 [DT] 120 [SHIFT] [;] 31
To delete 120 [SHIFT] [;] 31, press [AC].
Example 5 30 [DT] 50 [DT] 120 [SHIFT] [;] 31 [DT]
To delete 120 [SHIFT] [;] 31 [DT], press [SHIFT] [CL].
Example 6 50 [DT] 120 [SHIFT] [;] 31 [DT] 40 [DT] 30 [DT]
To delete 120 [SHIFT] [;] 31 [DT], press 120 [SHIFT] [;] 31
[SHIFT] [CL].
Example 7 [] 10 [DT] [] 20 [DT] [] 30 [DT]
To delete [] 20 [DT], press [] 20 [=] [Ans] [SHIFT] [CL].
Example 8 [] 10 [DT] [] 20 [DT] [] 30 [DT]
To delete [] 20 [DT], press [] 20 [SHIFT] [;] [] 1 [DT].
Operation
Number of digits displayed

Up to 10 digits
Up to 10 digits
Up to 10 digits
Up to 8 digits
P(t)
t2
e dt
1 t
2 -
Calculation range (in BASE-N mode)

Binary
Positive : 0111111111x 0
Negative : 1111111111x 1000000000
Octal
Positive : 3777777777x0
Negative : 7777777777x4000000000
Decimal
Positive : 2147483647x0
Negative : 1x2147483648
Hexadecimal Positive : 7FFFFFFFx0
Negative : FFFFFFFFx80000000
Sub-menu for BASE-N operation
In the sub-menu, you can select operators AND, OR, XNOR, XOR,
NOT, and NEG, as well as the number system identifier "d", "h",
"b" and "o".
Press [LOGIC] consecutively to scroll through the menu.
Press [LOGIC] once.
t = xxx
n
X or N o t N e g
1
2
3
b
3
1
2
3
4
5
6
7
8
9
10
Example
Binary, Octal, Decimal, Hexadecimal Conversions

Conversion Using Number System Mode Key
Calculation results can be converted to any specified number
system by using the corresponding number system mode key.
How is 2210 expressed in
binary, octal and
hexadecimal number
system?
Operation
[MODE][MODE][3]
[DEC]
22[=]
[BIN]
[OCT]
[HEX]
Display
b
d
22d
10110b
26o
16h
Conversion using number system specification key

Value from a different number system input when a specific
number system mode is being used.
Example
Operation
[MODE][MODE][3][DEC]
What are the decimal
values for 2A16 and 2748? [LOGIC][LOGIC][LOGIC][2]2A[=]
[LOGIC][LOGIC][LOGIC][4]274
[=]
What are the hexadecimal [HEX]
values for 12310 and 10102? [LOGIC][LOGIC][LOGIC][1]123[=]
[LOGIC][LOGIC][LOGIC][3]1010[=]
What are the octal values [OCT]
for 1516 and 11002?
What are the binary values [BIN]
for 3610 and 2C16?
[LOGIC][LOGIC][LOGIC][2]2C[=]
Display
(Lower)
d
42d
d
188d
h
7bh
Ah
o
25o
14o
b
100100b
101100b
Basic Arithmetic Operations Using Binary, Octal, Decimal,

Hexadecimal Values
Example
101112110102
= 1100012
B4716DF16
= A6816
1238ABC16 = 37AF416
= 22808410
1F2D1610010 = 788110
= 1EC916
765481210
= 334.333333310
= 5168
1234101EF16248
= 23528
= 125810
Operation
[MODE][MODE][3]
[BIN]
10111[]11010[=]
[HEX]
B47[]DF[=]
[OCT]123[=][HEX][]ABC[=]
[DEC]
[HEX]1F2D[=][DEC][]100[=]
[HEX]
[OCT]
7654[=][DEC][]12[=]
[OCT]
[OCT]
[LOGIC][LOGIC][LOGIC][1]1234
[][LOGIC][LOGIC][LOGIC][2]
1EF[]24[=]
[DEC]
Display
h
b
110001b
31h
A68h
37AF4h
228084d
7881d
1EC9h
17311o
334d
516o
o
2352o
1258d
Negative Expressions
Example
Operation
How is 1100102
[MODE][MODE][3]
expressed as a negative? [BIN]
[LOGIC][LOGIC][3]
110010[=]
[OCT]
How is 728 expressed
[LOGIC][LOGIC][3]
as a negative?
72[=]
How is 3A16 expressed [HEX]
[LOGIC][LOGIC][3]
as a negative?
3A[=]
Display
h
b
1111001110b
o
7777777706o
h
FFFFFFC6h
Logical Operations
Logical operations are performed through logical products
(and), logical sums (or), negative (Not), exclusive logic sums
(xor), and negation of exclusive logical sums (xnor).
Example
1916 AND 1A16 = 1816
11102 AND 368 = 11102
238 OR 618 = 638
12016 OR 11012 = 12D16
10102 AND (A16 OR 716)
= 10102
516 XOR 316 = 616

2A16 XNOR 5D16
= FFFFFF8816
Negation of 12348
Negation of 2FFFED16
Operation
[MODE][MODE][3]
[HEX]
19[LOGIC][1]1A[=]
[BIN]
1110[LOGIC][1][LOGIC][LOGIC]
[LOGIC][4]36[=]
[OCT]
23[LOGIC][2]61[=]
[HEX]
120[LOGIC][2][LOGIC][LOGIC]
[LOGIC][3]1101[=]
[BIN]
1010[LOGIC][1][(][LOGIC]
[LOGIC][LOGIC][2]A[LOGIC][2]
[LOGIC][LOGIC][LOGIC][2]
7[)][=]
[HEX]
5[LOGIC][LOGIC][1]3[=]
[HEX]
2A[LOGIC][3]5D[=]
[OCT]
[LOGIC][LOGIC][3]1234[=]
[HEX]
[LOGIC][LOGIC][3]
2FFFED[=]
t2
e dt
1 t
2 0
R(t)
t2
e dt
1 +
2 0
158.5
160.5
163.3
167.5
170.2
173.3
175.5
178.6
180.4
186.7
1
1
2
2
3
4
2
2
2
1
Operation
Display
[MODE][MODE][1] (SD Mode)

0.
[SHIFT][CLR][1][=] (Memory cleared)
160.5
158.5[DT]160.5[DT]
163.3
163.3[DT][DT]
167.5
167.5[DT][DT]
170.2
170.2[DT][DT][DT]
173.3
173.3[DT][DT][DT][DT]
175.5
175.5[DT][DT]
178.6
178.6[DT][DT]
186.7
180.4[DT][DT]186.7[DT]
20.
[RCL][C](Number of data)
Perform the single3440.1
variable statistical
[RCL][B](Sum of data)
592706.09
calculations.
[RCL][A](Sum of square of data)
172.005
[SHIFT][x][=](Mean)
7.041624457
[SHIFT][xn][=](Population SD)
7.224554257
[SHIFT][xn1][=](Sample SD)
-1.633855948
Normalized variate t
160.5[SHIFT][DISTR][4][=]
-1.6339
for 160.5cm.
0.496334336
Normalized variate t
175.5[SHIFT][DISTR][4][=]
0.4963
for 175.5cm
Percentage of the
[SHIFT][DISTR][1]0.4963[)]
students fall in the
[][SHIFT][DISTR][1][]
0.63902
range 160.5 to 175.5cm 1.6339[)]
(63.9%)
Percentile of 175.5cm [SHIFT][DISTR][3]0.4963[)]
0.30984
tall student
[=]
(31.0 percentile)
Input data as shown
in the above table
o
4
After selecting the operator, press [LOGIC] once more to exit.
Example
Q(t)
Example: The following table shows the results of

measurements of the height of 20 college students. Determine
what percentage of the students fall in the range of 160.5cm
to175.5cm. Also, in what percentile does the 175.5cm tall
student fall?
Class No.
Height (cm)
Frequency
A nd O r X n o r
1
2
3
h
2
1.982142857
Input a value from 1 to 4 to select the probabilty distribution

calculation you want to perform.
Number system
d
1
52.
8.
427.
22805.
53.375
1.316956719
1.407885953
P ( Q( R( t
1 2 3 4
Binary
Octal
Decimal
Hexadecimal
Press [LOGIC] further.
0.
Probability Distribution Calculation

You can calculate probabiltiy distributions for single-variable
statistics by pressing [SHIFT] [DISTR] in the SD mode.
Press [SHIFT] [DISTR] which produces the screen shown
below:-
Negative numbers in binary, octal, hexadecimal are expressed

as two's complements.
Number of digits displayed in each number system
Press [LOGIC] again.
Display
[MODE][MODE][1] (SD Mode)

[SHIFT][CLR][1][=] (Memory cleared)
55[DT]54[DT]51[DT]
55[DT]53[DT][DT]54[DT]
52[DT]
What is deviation of the [RCL][C](Number of data)
unbiased variance, and [RCL][B](Sumof data)
the mean of the above [RCL][A](Sum of square of data)
data?
[SHIFT][x][=](Mean)
[SHIFT][xn][=](Population SD)
[SHIFT][xn1][=](Sample SD)
[SHIFT][xn1]
[x2][=](Sample variance)
Data 55, 54, 51, 55, 53,
53, 54, 52
Display
d
h
18h
11000b
1110b
16o
63o
33h
12dh
100101101b
1010b
Ah
6h
6h
FFFFFF88h
7777777610o
7777776544o
FFFFFd64h
FFd00013h
Statistical Calculations
This unit can be used to make statistical calculations including
standard deviation in the "SD" mode, and regression
calculation in the "REG" mode.
Standard Deviation
In the "SD" mode, calculations including 2 types of standard
deviation formulas, mean, number of data, sum of data, and
sum of square can be performed.
Data input
1. Press [MODE] [MODE] [1] to specify SD mode.
2. Press [SHIFT] [CLR] [1] [=] to clear the statistical memories.
3. Input data, pressing [DT] key (= [M+]) each time a new piece
of data is entered.
Example Data: 10, 20, 30
Key operation: 10 [DT] 20 [DT] 30 [DT]
When multiples of the same data are input, two different
entry methods are possible.
Example 1 Data: 10, 20, 20, 30
Key operation: 10 [DT] 20 [DT] [DT] 30 [DT]
The previously entered data is entered again each time the
DT is pressed without entering data (in this case 20 is
re-entered).
Example 2 Data: 10, 20, 20, 20, 20, 20, 20, 30
Key operation: 10 [DT] 20 [SHIFT] [;] 6 [DT] 30 [DT]
By pressing [SHIFT] and then entering a semicolon followed
by value that represents the number of items the data is
repeated (6, in this case) and the [DT] key, the multiple data
entries (for 20, in this case) are made automatically.
Regression Calculation
In the REG mode, calculations including linear regression,
logarithmic regression, exponential regression, power
regression, quadratic regression and inverse regression can be
performed.
Linear regression
Linear regression calculations are carried out using the
following formula:
y = A + Bx.
Data input
Press [MODE] [MODE] [2] [1] to specify linear regression
under the "REG" mode.
Press [Shift] [Scl] [1] [=] to clear the statistical memories.
Input data in this format: <x data> [,] <y data> [DT]
When multiples of the same data are input, two different
entry methods are possible:
Example 1 Data: 10/20, 20/30, 20/30, 40/50
Key operation: 10 [,] 20 [DT]
20 [,] 30 [DT] [DT]
40 [,] 50 [DT]
The previously entered data is entered again each time the
[DT] key is pressed (in this case 20/30 is re-entered).
Example 2 Data: 10/20, 20/30, 20/30, 20/30, 20/30, 20/30, 40/50
Key operation: 10 [,] 20 [DT]
20 [,] 30 [SHIFT] [;] 5 [DT]
40 [,] 50 [DT]
By pressing [SHIFT] and then entering a semicolon followed
by a value that represents the number of times the data is
repeated (5, in this case) and the [DT] key, the multiple data
entries (for 20/30, in this case) are made automatically.
Deleting input data
There are various ways to delete value data, depending on
how and where it was entered.
Example 1
10 [,] 40 [DT]
20 [,] 20 [DT]
30 [,] 30 [DT]
40 [,] 50
To delete 40 [,] 50, press [AC]
Example 2
10 [,] 40 [DT]
20 [,] 20 [DT]
30 [,] 30 [DT]
40 [,] 50 [DT]
To delete 40 [,] 50 [DT], press [SHIFT][CL]
Example 3
To delete 20 [,] 20 [DT], press 20 [,] 20 [SHIFT][CL]
Example 4
[] 10 [,] 40 [DT]
[] 40 [,] 50 [DT]
To delete[]10[,]40[DT], press[]10[=][Ans][,]40[SHIFT][CL]
Key Operations to recall regression calculation results
Key operation
Result
[SHIFT][A][=]
[SHIFT][B][=]
[SHIFT][C][=]
[SHIFT][r][=]
[SHIFT][x][=]
[SHIFT][y][=]
[SHIFT][yn]
[SHIFT][yn1]
[SHIFT][y]
[SHIFT][xn]
[SHIFT][xn1]
[SHIFT][x]
[RCL][A]
[RCL][B]
[RCL][C]
[RCL][D]
[RCL][E]
[RCL][F]
Constant term of regression A

Regression coefficient B
Regression coefficient C
Correlation coefficient r
Estimated value of x
Estimated value of y
Population standard deviation, yn
Sample standard deviation, yn1
Mean, y
Population standard deviation, xn
Sample standard deviation, xn1
Mean, x
Sum of square of data, x2
Sum of data, x
Number of data, n
Sum of square of data, y2
Sum of data, y
Sum of data, xy
The regression formula is y = A + Bx. The constant term of

regression A, regression coefficient B, correlation r, estimated
value of x, and estimated value of y are calculated as shown
below:
A = ( yx )/n
B = ( nxyxy ) / ( nx2(x )2)
r = ( nxyxy ) / (( nx2(x )2)( ny2(y )2))
y = A + Bx
x = ( yA) / B
Operation
Temperature and length [MODE][MODE][2][1]

of a steel bar
("REG" then select linear regression)
Temp
Length
[SHIFT][CLR][1][=]
10C
1003mm 10[,]1003[DT]
15C
1005mm 15[,]1005[DT]
20C
1010mm 20[,]1010[DT]
25C
1011mm 25[,]1011[DT]
30C
1014mm 30[,]1014[DT]
Using this table, the
[SHIFT][A][=](Constant term A)
regression formula and [SHIFT][B][=]
correlation coefficient (Regression coefficient B)
can be obtained. Based [SHIFT][r][=]
(Correlation coefficient r)
on the coefficient
formula, the length of 18[SHIFT][y](Length at 18C)
the steel bar at 18C
1000[SHIFT][x](Temp at 1000mm)
and the temperature
[SHIFT][r][x2][=]
(Critical coefficient)
at 1000mm can be
estimated. Furthermore [(][RCL][F][][RCL][C][]
the critical coefficient [SHIFT][x][][SHIFT][y][)][]
(r2) and covariance can [(][RCL][C][]1[)][=](Covariance)
also be calculated.
The logarithmic regression formula y = A + Blnx. As x is input,
In(x) will be stored instead of x itself. Hence, we can treat the
logarithmic regression formula same as the linear regression
formula. Therefore, the formulas for constant term A,
regression coefficient B and correlation coefficient r are
identical for logarithmic and linear regression.
Example
Operation
Display
0.
10.
15.
20.
25.
30.
997.4
0.56
0.982607368
1007.48
4.642857143
0.965517241
35.
Display
xi
yi
[MODE][MODE][2][2]
29
1.6
("REG" then select Log regression)
50
23.5
[SHIFT][CLR][1][=]
0.
74
38
29[,]1.6[DT]
29.
103
46.4
50[,]23.5[DT]
50.
118
48.9
74[,]38[DT]
74.
The logarithmic
103.
regression of the above 103[,]46.4[DT]
118[,]48.9[DT]
118.
data, the regression
formula and correlation [SHIFT][A][=](Constant term A)
111.1283976
coefficient are obtained. [SHIFT][B][=](Regression coefficient B) 34.0201475
Furthermore, respective [SHIFT][r][=](Correlation coefficient r) 0.994013946
estimated values y and
37.94879482
80[SHIFT][y](y when xi=80)
x can be obtained for
224.1541313
xi = 80 and yi = 73 using 73[SHIFT][x](x when yi=73)
the regression formula.
A number of logarithmic regression calculation results differ

from those produced by linear regression. Note the following:
Linear regression
Logarithmic regression
x
x2
xy
Inx
(Inx)2
yInx
If we assume that lny = y and lnA = a', the exponential
regression formula y = AeBx (ln y = ln A +Bx) becomes the
linear regression formula y =a' + bx if we store In(y) instead of y
itself. Therefore, the formulas for constant term A, regression
coefficient B and correlation coefficient r are identical for
exponential and linear regression.
A number of exponential regression calculation results differ
from those produced by linear regression. Note the following:
Linear regression
Exponential regression
y
y2
xy
Iny
(Iny)2
xIny
Example
Operation
xi
yi
[MODE][MODE][2][3]
6.9
21.4
("REG" then select EXP regression)
12.9
15.7
[SHIFT][CLR][1][=]
19.8
12.1
6.9[,]21.4[DT]
26.7
8.5
12.9[,]15.7[DT]
35.1
5.2
19.8[,]12.1[DT]
Through exponential
regression of the above 26.7[,]8.5[DT]
35.1[,]5.2[DT]
coefficient are obtained. [SHIFT][B][=]
(Regression coefficient B)
Furthermore, the
regression formula is
[SHIFT][r][=]
used to obtain the
respective estimated
values of y and x, when 16[SHIFT][y](y when xi=16)
20[SHIFT][x](x when yi=20)
xi = 16 and yi = 20.
Display
0.
6.9
12.9
19.8
26.7
35.1
30.49758743
0.049203708
0.997247352
13.87915739
8.574868046
If we assume that lny = y, lnA =a' and ln x = x, the power
regression formula y = AxB (lny = lnA + Blnx) becomes the
linear regression formula y = a' + bx if we store In(x) and In(y)
instead of x and y themselves. Therefore, the formulas for
constant term A, regression coefficient B and correlation
coefficient r are identical with the power and linear regression.
A number of power regression calculation results differ from
those produced by linear regression. Note the following:
Linear regression
Power regression
Inx
(Inx)2
Iny
(Iny)2
InxIny
Example
Operation
Display
xi = 40 and yi = 1000.
6587.674584
20.2622568
0.998906254
Inverse regression
Power regression calculations are carried out using the
following formula:
y = A + ( B/x )
Data input
Press [MODE] [MODE] [2] [] [2] to specify inverse regression
Press [SHIFT] [CLR] [1] [=] to clear the statistical memories.
Input data in this format: <x data>,<y data> [DT]
To make multiple entries of the same data, follow procedures
described for linear regression.
Deleting input data
To delete input data, follow the procedures described for linear
regression
If 1/x is stored instead of x itself, the inverse regression formula
y = A + ( B/x ) becomes the linear regression formula y = a + bx.
Therefore, the formulas for constant term A, regression
coefficient B and correlation coefficient r are identical with the
power and linear regression.
A number of inverse regression calculation results differ from
those produced by linear regression. Note the following:
Linear regression
Inverse regression
(1/x)
(1/x)2
(y/x)
Example
Operation
Store a Formula in Memory

Press [PROG] to enter the programming mode. The twenty
memory names (0~9, A~J) will appear on the screen and the
memory capacity available will be shown on the lower right of
the display.
D
P 0123456789
900
You can use [] or [] to select a formula memory name. The
currently selected formula memory is indicated by its name
flashing on the display. The [] and [] keys move the
selection over to the left and right. After selecting the desired
formula memory, press [=] key. The display should appear as
shown below if that formula memory is empty. Otherwise, the
formula stored in that memory will be recalled and the user
can do editing.
WRT
The "0" at the lower right shows how many steps there are
between the present position of the cursor and the beginning
of the formula. Since we have not input anything yet, this
number indicated zero steps in memory.
Now, we try to input the formula "Y = X2 + 3X 12" into the
memory.
[ALPHA] [Y] [ALPHA] [=] [ALPHA] [X] [x2]
Y=X 2 +3X12 _
[] [3] [ALPHA] [X] [] [1] [2]
10
Press [PROG] to store the formula.
WRT
The lower line will show the number of steps input. The
maximum number of step inputs for each formula can't
exceed 79. At the end of formula input, you can press [PROG]
to go back to memory programming menu. Say, we have the
formula in memory "0".
D
P 0 123456789
890
The memory "0" is shown in inverted display on the LCD to
indicate that the memory P0 contains a formula. And the lower
right of the LCD shows the number of steps left for
programming.
Recall a Formula Memory
Press [PROG] to enter the memory programming mode. The
memories which contain formulae are indicated by their
names being displayed in inverted color.
P 0 123456789
875
You can move the cursor to locate the desired program. Then
press [=]. For example, we retrieve program P5 in which
123456 are stored.
WRT
123+456
Since the cursor stays at the beginning of the formula, hence

the lower right of the LCD shows zero step. As you move the
cursor to the right, the number of steps displayed will be
updated at the same time.
123+456 _
WRT
In the meantime, the user can edit the formula by character

inserting, deleting or replacing.
Delete a Formula Memory
Select the desired program memory as described above. Say,
P6 is selected. Press [=] to retrieve the program. Let "123456"
is stored.
WRT
123x456
P 0 12345 6789
882
The inverted display at the location of "6" is restored to normal
to indicate that the program P6 is empty now.
Executing a Formula in Memory
Press [PROG] to open the program memory menu. Same in
program writing mode, you can choose the desired program
by moving the cursor with the use of [] or []. Then press
[SHIFT] [CALC] to execute the program. Say P0 is selected. The
formula stored is "Y = X2 + 3X 12".
X?
WRT
0
D
WRT
Y=X 2 +3X12
58
Program Data All Clear

Press [SHIFT] [CLR] to view the CLR menu. Then key in [2] to
select the program reset function. The unit will ask if you really
want to erase all the program data by showing the message
"Reset Prog?" as shown below.
Reset Prog?
To confirm the program data erasure, press [=]. Or you can

press any other keys to exit and restore the previous display.
As the program data has been reset, the display will show
"Prog Deleted".
Prog Deleted
Complex Number Calculation

Press [MODE] [2] to enter the "CMPLX" mode for calculations
that include complex numbers. In "CMPLX" mode, only
variables A, B, C and M can be used. The others are used for
storing the imaginary parts of values.
Operation
xi = 10 and yi = 9.
6.144200627
6.533575318
0.950169099
Quadratic Regression
Quadratic regression calculations are carried out using the
following formula:
y = A + Bx + Cx2
Data input
Press [MODE] [MODE] [2] [] [3] to specify quadratic
regression under the "REG" mode.
Deleting input data
regression.
linear regression calculations.
The regression formula is y = A + Bx + Cx2 where A, B, C are
regression coefficients.
C = [(nx2(x)2) (nx2yx2y )(nx3x2x) (nxy
xy)][(nx2(x)2) (nx4(x2)2)(nx3x2x)2]
B = [nxyxyC (nx3x2x)](nx2(x)2)
A = (yBxCx2) / n
To read the value of x3, x4 or x2y, you can recall memory
[RCL] M, Y and X respectively.
0.
6.
8.i
5.
53.13010235
where a is the starting point

b is the ending point
n is the value such that the number divisions N=2n
Integration calculation is performed using Simpson's rule to
determine function f(x). Because of this, partition of the
integrated area is necessary, however if the number of
divisions is not specified, the unit automatically sets N
according to the formula. To specify the number of divisions
for N=2n, n can be an integer from 1 to 9.
y = f(x)
[dx] [2] [ALPHA] [X] [x2] []

[3] [ALPHA] [X] [] [4] [,] (f(x) input)
(2x 2 +3x+4, _
[1] [,] [5] [,] (a,b
2 +3x+4,1,5, _
[=]
input)
0.
b?
Let "b" be 2.
[2] [=]
n?
Enter [3] for "n", then press [=].

The answer expression will be
executed.
=(x+2)x y 4/4
0.
0.
D
If you want to find the integration for the same expression

again, you can press [=] during the display of the answer
expression to go back to the following state.
a?
1.
+3x+4,1,5,6) _
D
Expression Integration
The following is a list of the built-in expression integration
formulae:
xndx = xn+1/(n+1)
dx/x = ln |x|
axdx = ax/ln a
(ax+b)ndx = (ax+b)n+1/a(n+1) where n1
(ax+b)1dx = (1/a) ln |ax+b|
eaxdx = (1/a)eax
baxdx = (1/a)bax/ln b
xeaxdx = (eax/a2) (ax1)
ln ax dx = x ln ax x
xn ln ax dx = xn+1/(n+1) ln axxn+1/(n+1)2 where n1
x1 ln ax dx = (1/2) (ln ax2)
Example :- Solving the quadratic equation x22x3=0

Press [EQU] then press [2], you will be asked to input the
coefficient a.
a?
Enter a as "1" by pressing [1][=].

You will proceed to the input of b.
b?
Enter "2" for b by keying in [2][=].

Then go to the entry for c.
c?
Enter "3" for c.
0.
0.
0.
3_
Press [=] to confirm the entry and the equation solving starts.
Solving...
When the roots are available, the display will show x1 first then
x2 as below.
X 1=
CMPLX
Since x1 is an imaginary number, the icon "CMPLX" will flash

and you can read the imaginary part by pressing
[SHIFT][REIM].
CMPLX
X 1=
1.414213562
Press [=] or [] to read next root.
X 2=
CMPLX
1.
In this case, x2 is also an imaginary number.

Press [SHIFT][REIM] to read
the imaginary part.
CMPLX
X 2=
1.414213562
If you want to enter another values for a, b, c, you can press [=]
to restart the coefficient input procedures. Or you can open
the main menu to select another type of equations or stop
solving function by pressing [AC].
Matrix Calculations
In matrix calculation, you can perform the following
operations on matrices of up to 3 rows and 3 columns, i.e.
addition, subtraction, multiplication, transpose, invert, scalar
product, determinant and absolute value.
There are four matrix memories, A, B, C and Matrix ANS. These
four matrices exist all the time and even when the calculator is
turned off.
To start matrix calculation, you can press [MAT]. The following
menu will be displayed.
Numerical Differentiation
You can activate "Differentiation" function by pressing [d/dx]
and input differentials using the following format.
Four operations are available. They are Edit, Sel, Det and Trn. To
switch to "Trn", press [] once.
Edit Sel Det

1
2
3
Trn
4
[d/dx] f(x) [,] a [,] x

where f(x) is the function expression
a is the point at which the user wants to determine
the derivative, and
x is the increase / dedcrease of x
Central difference is used for calculating the derivative which
is expressed as:f'(a)=(f(a+x)f(ax))/2x
Example: To determine the derivative at point x = 3 for the
function y=x3+4x2+x6 when the increase / decrease of x is
defined as x = 15
[SHIFT] [d/dx] [ALPHA] [X]
[SHIFT] [X3][][4] [ALPHA][X] [X2]
d/dx(x 3 +4x 2 _
[] [ALPHA] [X] [] [6] [,]
x 3 +4x 2 +x6, _
"Edit" allows you to edit matrix A, B or C.

"Sel" lets you select one matrix among A, B, C and ANS and
define all the elements
"Det" for finding the determinant of the selected matrix.
"Trn" for transposing the selected matrix.
How to define a matrix
First, select "Edit" in the main menu. You will be asked to select
one the matrices among A, B and C.
A
1
[=]
d/dx(x 3 +4x 2 +
52.
Solve Function
The solve feature lets you solve an expression using variable
values you want without the need to transform or simplify the
expression. For example, in the expression "B=AX5", you can
define A, B to findX, or define A, X to find B, or define B, X to find A.
Newton's method is used for solving functions, in which, error
can occur. Certain expressions or initial values may result in
error without convergence of results. If an expression does not
include an equal sign "=", the Solve function produces a
solution for expression = 0.
0.
You can enter the value for the number of rows. Only 1 to 3 is
allowed. If the number other than 1 to 3 is entered, an error
message ("Dim ERROR") will be displayed. After the entry of
the number of rows, you can move to the input of the number
of columns.
n?
x6,3,1E5) _
C
3
m?
+4x +x6,3, _
input x, i.e.
[1] [EXP] [SHIFT] [()] [5] [)]
B
2
After selection of matrix, you will be asked to define the

dimension of the selected matrix.
Input the point x=a for which you want to determine the
derivative.
[3] [,]
2
0.
Same as "m", only 1 to 3 is allowed for input.

Once the dimension of the selected matrix has been defined,
you will be asked to input the value of all the elements (axy) in
the matrix where x ranges from 1 to m and y from 1 to n. The
display is shown below:-
M a t A 11
0.
If you want to go back to the main menu, press [MAT] again.

How to perform matrix calculation
Example: To multiply Matrix A by Matrix B, where
1
4
2
1
Matrix B =
2
Matrix A =
2
0
5
0
4
3
1
You can enter a formula or retrieve a formula from the formula

memory. For example, if the formula is:y=ax2+6x9
First, define Matrix A

Press [MAT] [1] [1] to select
Matrix A
m?
[AC] [ALPHA] [Y] [=] [ALPHA] [A]

[ALPHA] [X] [X2] [+] [6]
[ALPHA] [X] [] [9]
Input [3] [=] for "m"
n?
Input [2] [=] for "n"

(A is a 32 matrix)
M a t A 11
Y=AX 2 +6X9 _
D
After entering the formula, you can press [SOLVE] to start

function solving. You will be asked for the values of all
variables in the formula. To define the variable, you can input
the value and press [=] for confirmation and proceed to next
variable. Or you can skip entering the value by pressing [=].
[SOLVE]
If you want to leave Y=0, you can
press [=] directly without entering
any values. And the display will
show the next variable, A.
Y?
A?
0.
0.
Set A = 2 by entering [2]
Press [=] to proceed to the last

variable "X"
X?
0.
If you want, you can also skip the

Y=AX 2 +6X9
input for X by pressing [=].
After the entry for the last
variable, the formula will be displayed again on the upper line
of the display. The cursor will stay at the first variable of the
formula. If it is the variable you want to solve for, press
[SOLVE]. But if it is not the desired variable, press [] or [] to
locate the variable you want. For example, you want to solve X
for the formula above.
D
[] []
Y=AX 2 +6X9
Press [=] to display the value of

the left expression.
1.098076211
D
Left expr=
Press [=] again to display the

value of the right expression.
0.
Rgt expr=
0.
If you want to restart the function solving for the same

formula, you can press [=] once more to recycle the solving
procedure. You will be asked again to input the value for all
the variables. If you want to exit from solving function, press
[AC].
To use the "SOLVE" function by retreiving a formula from the
formula memory, press [PROG], [SHIFT] [CALC], [SOLVE], then
enter the value for each variable when asked.
Lin Quad Cub

1
2
3
0.
0.
0.
Then input all the elements for Matrix A:[1] [=] [2] [=] [4] [=] [0] [=] [] [2] [=] [5] [=] [AC]
Second, define Matrix B
Matrix B
m?
Input [2] [=] for "m"
n?
Input [3] [=] for "n"

(B is a 23 matrix)
M a t B 11
0.
0.
0.
Then input all the elements for Matrix B:[] [1] [=] [0] [=] [3] [=] [2] [=] [] [4] [=] [1] [=] [AC]
Matrix A
MatA_
Then input []
MatAx_

Matrix B
MatAxMatB_
Press [=] to start the execution. The display will show the first
element of the ANS matrix.
M a t A n s 11
Press [SOLVE] to calculate the value of X. The answer will be

displayed as follow:[SOLVE]
3.
By pressing either one of the four direction arrows , you can

scroll through all the elements of anwer. In this case the
answer is shown below:-
3 8
4
0
12 20
5
12
1
In the similar way, you can carry out subtraction, multiplication,

scalar product calculation and matrix invert. For absolute
value, use [Abs] key in front of the matrix. For doing transpose
and determinant, select "Trn" and "Det" respectively in the
main menu and the answer display will show "TrnMatAns"
and "DetMatAns" on the upper line accordingly.
Previous Calculation Recall
Latest 20 calculations will be saved in the last calculation
memory and be able to recall using [] or [] key buttons.
The maximum total size is 400 characters.
(Note :- Answer for these latest 20 calculations will not be
stored. )
When the up-arrow is present on the right side of the LCD, it
indicates that there are previous calculations available in the
last calculation memory. You can press [] to retrieve and
show the previous calculation on the screen. The answer will
be calculated instantly and displayed as well. At the same
time, the down-arrow will be ON to indicate that more recent
calculations are stored in the last calculation memory.
Let the current display be
1+2
Press [] to read the previous

calculation.
1 0 0 2 _
2-unknown linear equations :-
Then you can press [] to go

back to the more recent
calculation.
1+2_
3-unknow linear equations :-
Replacing the Battery

Dim figures on the display of the calculator indicate that
battery power is low. Continued use of the calculator when the
battery is low can result in improper operation. Replace the
battery as soon as possible when display figures become dim.
If you select [1] (Linear), you can select further between two
unknowns and three unknowns.
Unknowns?
2
3
After you have made the selection, the calculator will ask you
for the corresponding coefficients.
a1xb1y = c1
a2xb2y = c2
a1xb1yc1z = d1
a2xb2yc2z = d2
a3xb3yc3z = d3
After you has been asked and enter all coefficients, the first
answer will be displayed as below.
X=
1.5
The icon "" will be ON if there are still further answers. You
can press [=] or [] to read the next answer.
Y=
(2x 2 +3x+4,1
134.6666667
The solving function for quadratic equation and cubic

equation is similar to linear equations. After the entry for all
the coefficients, the variable "x" will be calculated and the
answer will be displayed. For quadratic equations, there will be
two answers, i.e., x1 and x2 available as the maximum. For cubic
equations, there will be three answers, i.e., x1 , x2 and x3
available as the maximum.
Or you can press [] or [] to search for another expression

for integration. On the other hand, if you want to exit from
expression integration, press [AC] during the display of the
answer expression.
Once the user presses [EQU] to enter equation solving mode,

the display will show all these three choices.
N equal parts
Examples of operation
Example Calculate the following: 15 (2x23x4)dx
[MODE][1]
_
(specify "COMP" mode)
[6] [)] (n
a?
Equation Solving Function

Three choices are provided for users to select. They are : Linear equation
Quadratic equation
Cubic equation
Input of function f(x) and integration calculation

Press [dx] to specify integration calculation.
Input the formula for the function f(x), then input integral
partitions [a, b].
Note:- f(x) can use the variable X only. Anything other than
X, i.e., A ~ F, Y are treated as a constant, and its memory
contents are applied.
Next input n and finish by inputting a parenthesis. Input of n
and parenthesis can be omitted. When input of n is omitted,
N (where N=2n) is automatically set.
Press [=] to execute calculation. Results are displayed in a
few seconds or a number of minutes.
input)
Press [SHIFT][CALC] to start.

You will be asked for the values
of all variables involved.
X=
Integration Calculation
Integration calculation can be carried out by entering the
integral calculus formula in the following format :[dx] f(x) [,] a [,] b [,] n
Display
0.
2.
3.
4.
5.
6.
7.272727273
11.28526646
Display
[MODE] [2] (CMPLX Mode)

(2+3i)+(4+5i)
[(]2[]3[i][)][][(]4[]5
[i][)][=]
[SHIFT][ReIm]
Find the absolute value [SHIFT][Abs][(]3[]4[i][)][=]
of (3+4i)
Determine the argument [SHIFT][arg][(]3[]4[i][)][=]
(3+4i)
xi
yi
[MODE][MODE][2][][2]
2
2
("REG" then select Inv regression)
3
3
[SHIFT][CLR][1][=]
4
4
2[,]2[DT]
5
5
3[,]3[DT]
6
6
4[,]4[DT]
Through inverse
regression of the above 5[,]5[DT]
6[,]6[DT]
Furthermore, the
[SHIFT][r][=]
used to obtain the
Press [PROG] to confirm the deletion and go back to

programming menu as below.
Example
Press [dx] and followed by [=] to start expression integration

function. The first integration expression in the list will be
displayed. You can press [] or [] to search the expression
you want. Then you can press [CALC] to calculate the answer
expression. You will be asked for the value of all variables such
as a, b and n. After the input of the last variable, the answer
expression will be shown on the upper display.
Example: Determine the integration of (ax+b)ndx
Fetch the desired expression
(ax+b) n dx
by pressing [dx] [=] [] [] []
Press [AC] to clear all entries in this program memory.

WRT
dx/(x ln ax) = ln |ln ax|

cos ax dx = (1/a) sin ax
sin ax dx = (1/a) cos ax
sin2 ax dx = (x/2)(sin 2ax)/4a
cos2 ax dx = (x/2)+(sin 2ax)/4a
sin ax cos bx dx = (cos(a+b)x/(2(a+b))+cos(ab)x/(2(ab)))
where a2b2
sin ax sin bx dx = sin(ab)x/(2(ab))sin(a+b)x/(2(a+b))
where a2b2
cos ax cos bx dx = sin(ab)x/(2(ab))+sin(a+b)x/(2(a+b))
where a2b2
sin ax cos ax dx = (cos 2ax)/4a
(cos ax / sin ax) dx = (1/a) ln |sin ax|
(sin ax / cos ax) dx = (1/a) ln |cos ax|
xsin ax dx = sin ax/a2 (xcos ax)/a
xcos ax dx = (cos ax)/x2 + (xsin ax)/a
sinh ax dx = (cosh ax)/a
cosh ax dx = (sinh ax)/a
sinh2 ax dx = (cosh 2ax)/4ax/2
cosh2 ax dx = (sinh 2ax)/4a+x/2
xsinh ax dx = x(cosh ax)/a(sinh ax)/a2
xcosh ax dx = x(sinh ax)/a(cosh ax)/a2
tanh ax dx = (ln cosh ax)/a
coth ax dx = (ln |sinh ax|)/a
tanh2 ax dx = x(tanh ax)/a
coth2 ax dx = x(coth ax)/a
Enter the value for "a" Say, 1

[1] [=]
You can press [=] again to recycle the formula execution.
0.
28.
30.
33.
35.
38.
0.238801072
2.771866153
x
x2
xy
Display
Formula Memory Function

This calculator has a built-in formula memory area of 900
steps, that allows the user to store a maximum of 20 formulae.
Key in [7] [=]
xi
yi
28
2410
("REG" then select Pwr regression)
30
3033
[SHIFT][CLR][1][=]
33
3895
28[,]2410[DT]
35
4491
30[,]3033[DT]
38
5717
33[,]3895[DT]
Through power
regression of the above 35[,]4491[DT]
38[,]5717[DT]
Furthermore, the
[SHIFT][r][=]
used to obtain the
Operation
xi
yi
29
1.6
("REG" then select Quad regression)
50
23.5
[SHIFT][CLR][1][=]
0.
74
38
29[,]1.6[DT]
29.
103
46.4
50[,]23.5[DT]
50.
118
48
74[,]38[DT]
74.
Through power
103.
regression of the above 103[,]46.4[DT]
118[,]48[DT]
118.
35.59856934
1.495939413
Furthermore, the
6.7162966703
[SHIFT][C][=]
used to obtain the
(Regression coefficient C)
13.38291067
47.14556728
20[SHIFT][x](x1 when yi=20)
xi = 16 and yi = 20.
175.5872105
[SHIFT][x](x2 when yi=20)
Power regression
Power regression calculations are carried out using the
following formula: y = AxB (lny = lnA + Blnx)
Data input
Press [MODE] [MODE][2] [] [1] to specify power regression
Deleting input data
regression.
x
x2
y
y2
xy
Example
Exponential regression
Exponential regression calculations are carried out using the
following formula:
y = AeBx (ln y = ln A +Bx)
Data input
Press [MODE] [MODE] [2] [3] to specify exponential
regression under the "REG" mode.
Deleting input data
regression.
linear regression calculations.
Example
Logarithmic regression
Logarithmic regression calculations are carried out using the
following formula:
y = A + Blnx
Data input
Press [MODE] [MODE] [2] [2] to specify logarithmic
regression under "REG" mode.
Input data in this format: <x data>, <y data> [DT]
Deleting input data
regression.
1.5
If Y is the last answer, the icon "" will be lighted instead. You
can scroll back to the answer X by pressing []. Or you can
press [=] to restart the input of all coefficients.
To exit from "EQU" function, you can press [AC] anytime
except in the input state for coefficients.
Quadratic equation :-
ax2bxc = 0
Cubic equation :-
ax3bx2cxd = 0
3.
To replace the battery: Remove the two screws that hold the back cover in place and
then remove the back cover,
Remove the old battery,
Wipe off the side of the new battery with a dry, soft cloth.
Load it into the unit with the positive(+) side facing up.
Replace the battery cover and secure it in place with the two
screws.
Press [ON] to turn power on.
Auto Power Off

Calculator power automatically turns off if you do not
perform any operation for about six minutes. When this
happens, press [ON] to turn power back on.
Specifications
Power supply: single CR2025 battery
Operating temperature: 0 ~ 40C (32F ~ 104F)

Uputa Kaiser - Calc - DQ

Uploaded by

Copyright:

Available Formats

Uputa Kaiser - Calc - DQ

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Uputa Kaiser - Calc - DQ

Uploaded by

Copyright:

Available Formats

"NORM" mode "[MODE] [MODE] [MODE] [MODE] [3]" :cancels "Fix" and "Sci" specifications.

This operation also

Please read before using.

You can simultaneously check the calculation formula and its

"Eng" mode "[MODE] [MODE] [MODE] [MODE] [MODE] [1]"

Overflow and Errors

In combination with "Fix", "Sci" or "Norm" mode, you can cause

Example: To change an input of cos60 to sin60 :[cos] [6] [0]

Press [MODE] again.

Press [MODE] again.

Deg Rad Gra

Fix Sci Norm

Press "MODE" once more to leave the menu.

Note: The five calculation modes listed above are totally

Specifying the Format of Calculation Results

1006 = 16.66666666 100 [] 6 [=]

Rounding the Intermediate Result

Example: To correct an input of 369 2 to 369 2 :[3] [6] [9] [] [] [2]

If a character has been omitted from a formula, use the ""

15 []26 [SHIFT] [%]

Shifting the Decimal Place

When formulas are input, the result of the formula's calculation

The replay function is not cleared even when [AC] is pressed or

Example: Input 123 to independent memory.

Correct the input by pressing

[AC] [4] [5] [6] [M+]

When interrupt operation is completed, press [=] once again to

Numeric values with 12 digits for a mantissa and 2 digits for an

(continuing) [] [3] [] [1] [4]

Example: To calculate 133 =

Example: Input 456 into memory "M" using M+. Memory

Addition/subtraction to or from sum in memory cannot be

"Disp" appears on the display when "" is used.

To clear memory contents, press [0] [STO] [M].

Other Functions ( , x2, x1, x!, 3, Ran#)

Taking any four out of

[AC] [4] [5] [6] [STO] [M]

The following operation is invalid in the BASE-N mode. When

Recall memory data

Add 25, subtract 12

Recall memory data

When input is made in a format such as "A=log 2", where the

Syn ERROR is generated when an attempt is made to input a

Example: Executing "A=log2" :[AC] [ALPHA] [A] [ALPHA] [=]

Permutation and Combination

If a variable expression is entered, the expression is first

(continuing) [] [3] [=]

Press [1] to select the command "Mcl".

Example: 123456 = 579

When you want to clear all the memories (except independent

round the stored

When [SHIFT] [INS] are pressed, the space that is opened is

To specify the number of significant digits (Sci.), press

If an unnecessary character has been included in a formula,

As with the number of decimal places, displayed results are

If after making corrections, input of the formula is complete,

Specifying the Number of Significant Digits

When numeric values or calculation commands are input, they