Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
92 views

Line Sensor Array

Line Sensor Array

Uploaded by

Mrinal
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
92 views

Line Sensor Array

Line Sensor Array

Uploaded by

Mrinal
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Line Sensor

Array [RKI-1032]

Users Manual
Robokits India
http://www.robokits.co.in
info@robokits.co.in

Robokits World
http://www.robokitsworld.com

http://www.robokits.co.in
http://www.robokitsworld.com

Page 1
Line Sensor Array [RKI-1032]

Thank you for purchasing Line Sensor Array. This unit has been carefully engineered and
tested to provide superior performance. This document covers the features and operation of
Line Sensor Array.
This is an easy-to-use module with 7 reflective sensors. All Photodiodes have ambient
light protection feature however sunlight/any other IR light source of same wavelength can
directly affect working of the sensor array.
It can be easily used with a microcontroller as it gives TTL compatible outputs. The
output pins can be directly connected to microcontroller pins which give active low output
when white line is detected. The main use of this module is for very fast line following.

Line Sensor Array Features

Simple interface (VCC, GND, 7 Outputs)


Open drain pulled up TTL compatible outputs
On Board 5V Regulator
Operating voltage from 5V - 12 V
7 Sensor in an array form
Indicator LEDs on top side for current status of sensor
Less sensitive to external ambient light
Can Detect color difference
Adjustment via potentiometer for best result
Reverse Polarity protection

Jumper Function

Jumper J1 can be used to select input voltage.


If you are giving input of +5V keep the jumper closed.
If you want to give more than 5V remove the jumper. This will enable the onboard 5V
regulator.
The board requires about 300ma of current. So if your 5V supply is not enough to drive
both your microcontroller board and the sensor board you can directly plug in your +VE
battery supply to VCC pin
Make sure you are not giving more than 5V to VCC pin when the jumper is closed. This
may damage the board permanently.

Interface

Pin 1 is Ground. Do not forget to short this pin with your microcontroller board ground
grid.
Pin 2 is VCC. You can supply either +5V directly from the board or battery voltage.
Please read the above section carefully before giving the voltage.
Pin 3-9 are output pins. These pins provide active low outputs. This means it will provide
Ground to microcontroller pins when the sensor is sensing light color.

http://www.robokits.co.in
http://www.robokitsworld.com

Page 2
Line Sensor Array [RKI-1032]

Board top layout

http://www.robokits.co.in
http://www.robokitsworld.com

Page 3
Line Sensor Array [RKI-1032]

Service and Support


Service and support for this product are available from Robokits India. The
(http://www.robokits.co.in) maintains current contact information for all Robokits products.

Robokits

Web

site

Limitations and Warrantees


The Line Sensor Array is intended for personal experimental and amusement use and in no case should be used where
the health or safety of persons may depend on its proper operation. Robokits provides no warrantee of suitability or
performance for any purpose for the product. Use of the product software and or hardware is with the understanding that
any outcome whatsoever is at the users own risk. Robokits sole guarantee is that the software and hardware perform in
compliance with this document at the time it was shipped to the best of our ability given reasonable care in manufacture
and testing. All products are tested for their best performance before shipping, and no warranty or guarantee is provided
on any of them. Of course the support is available on all of them for no cost.

Disclaimer
Copyright Robokits India, 2012
Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or
reproduced in any material or electronic form without the prior written consent of the copyright holder.
This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular
purpose is either made or implied.
This document provides preliminary information that may be subject to change without notice.

http://www.robokits.co.in
http://www.robokitsworld.com

Page 4
Line Sensor Array [RKI-1032]

You might also like