Navsea Op 3565 Vol 1

NAVSEA OP 3565/NAVAIR 16-1-529 VOLUME 1
SIXTH REVISION
TECHNICAL MANUAL
ELECTROMAGNETIC RADIATION HAZARDS (U)(HAZARDS

TO PERSONNEL, FUEL AND OTHER
FLAMMABLE MATERIAL) (U)
DISTRIBUTION STATEMENT C
Distribution authorized to U.S. Government agencies and their contractors;
administrative/operational use; 1 February 2003. Other requests for this document
must be referred to the Naval Ordnance Safety and Security Activity (NOSSA) (N716).
WARNING
This document contains technical data whose export is restricted by the Arms Export
Control Act (Title 22, USC, Sec 2751 et. seq.) or Executive Order 12470.
Violations of these export laws are subject to severe criminal penalties.
DESTRUCTION NOTICE
Destroy by any method that will prevent disclosure of
contents or reconstruction of the document.
THIS PUBLICATION SUPERSEDES NAVSEA OP 3565/NAVAIR 16-1-529

VOLUME 1 FIFTH REVISION DATED 15 JULY 1982
PUBLISHED BY DIRECTION OF COMMANDER, NAVAL SEA SYSTEMS COMMAND
This page left intentionally blank
NAVSEA OP 3565/NAVAIR 16-1-529 VOLUME 1

SIXTH REVISION
TECHNICAL MANUAL
ELECTROMAGNETIC RADIATION HAZARDS (U)(HAZARDS

TO PERSONNEL, FUEL AND OTHER
FLAMMABLE MATERIAL) (U)
DISTRIBUTION STATEMENT C
Distribution authorized to U.S. Government agencies and their contractors;
administrative/operational use; 1 February 2003. Other requests for this document
must be referred to the Naval Ordnance Safety and Security Activity (NOSSA) (N716).
WARNING
This document contains technical data whose export is restricted by the Arms Export
Control Act (Title 22, USC, Sec 2751 et. seq.) or Executive Order 12470.
Violations of these export laws are subject to severe criminal penalties.
DESTRUCTION NOTICE
Destroy by any method that will prevent disclosure of
contents or reconstruction of the document.
THIS PUBLICATION SUPERSEDES NAVSEA OP 3565/NAVAIR 16-1-529

VOLUME 1 FIFTH REVISION DATED 15 JULY 1982
PUBLISHED BY DIRECTION OF COMMANDER, NAVAL SEA SYSTEMS COMMAND
1 FEBRUARY 2003
NAVSEA OP 3565/NAVAIR 16-1-529

VOLUME 1 SIXTH REVISION
Reproduction for nonmilitary use of the information or illustrations contained in this publication is
not permitted. This does not preclude reproduction and use of any part of this manual by
contracted agencies responsible for the training and instruction of personnel who handle and
transport military ammunition, explosives, and related hazardous materials. The policy for military
use reproduction is established for the Army in AR 380-5, for the Navy and Marine Corps in
OPNAVINST 5510.1 series, and for the Air Force in Air Force Regulations 205-1.
LIST OF EFFECTIVE PAGES
The total number of pages in this manual is 144. They are all original Revision Six pages. The
date of issue for all pages in this manual is 1 February 2003.

FOREWORD
1. The purpose of this volume is to prescribe operating procedures and precautions to prevent
injury to personnel and ignition of volatile vapors from exposure to environmental
electromagnetic radiation (EMR). The sources of this EMR include communications
transmitters, radars, electronic countermeasures transmitters, and lasers.
2. This manual provides data and information concerning nonionizing radio frequency (RF),
hazards to personnel, fuel, and other flammable material, as well as laser hazards to personnel.
3. This manual cancels and supersedes NAVSEA OP 3565/NAVAIR 16-1-529/ NAVELEX
0967-LP-624-6010 Fifth Revision of 15 July 1982, which should be destroyed. The Chief of
Naval Operations, and Commanders of the Naval Air Systems Command and Space and Naval
Warfare Systems Command, concur with this provision.
4. This manual provides technical guidance to assist commanding officers in carrying out their
responsibilities for EMR safety. The procedures and precautions prescribed herein apply in
every instance within the Naval establishment where a person or a flammable vapor mixture is
exposed to RF fields of potentially hazardous intensity. Operational Commanders may waive
compliance with any provision when essential under emergency conditions. When
noncompliance with restrictions contained herein is essential, emergency procedures are
suggested and background information is provided in order to explain and minimize the risks
involved.
5. The concept of word usage and intended meaning which has been adhered to in preparing
this manual is as follows:
"Shall" has been used only when a specified action or procedure is mandatory.
"Should" has been used only when a specified action or procedure is recommended.
"May" and "need not" have been used only when a specified action or procedure is
optional.
"Will" has been used only to indicate futurity. No requirement for compliance is implied.
6. Changes and revisions to this publication will be promulgated by Naval Sea Systems
Command (NAVSEA) in a timely manner following coordination with the other cognizant
commanders. Interim changes will be made by letter or message as advance change notices,
which will be forwarded to the commanders directly concerned. Formal changes will be
forwarded to all addresses on the controlled distribution list of this manual and, subsequently,
will be included in formal revisions. Comments or suggestions relative to material to be
included in such changes should be forwarded as specified in chapter 1.
7. Assistance in evaluating specific electromagnetic or other radiation hazards or interpreting
provisions of this manual can be obtained by contacting NAVSEA, Code 53H3.
Foreword-1/(Foreword-2 Blank)

TABLE OF CONTENTS
Chapter/Paragraph
Page
List of Figures ....................................................................................................................... iv
List of Tables ......................................................................................................................... v
Safety Summary ................................................................................................................... vi
CHAPTER 1 INTRODUCTION .......................................................................................... 1-1
1-1.
1-2.
1-2.1
1-2.2
1-2.3
1-2.4
1-2.5
1-3.
1-3.1
1-3.2
1-3.3
1-3.4
1-3.5
1-3.6
1-4.
1-5.
1-6.
1-7.
1-8.
1-9.
1-10.
1-11.
Purpose and Scope of Manual ..................................................................... 1-1

Background .................................................................................................. 1-1
RF Hazards to Personnel.............................................................................. 1-1
Laser Hazards to Personnel ......................................................................... 1-2
Ionizing Radiation ......................................................................................... 1-2
RF Hazards to Fuel....................................................................................... 1-2
RF Hazards to Ordnance .............................................................................. 1-2
Responsibilities ............................................................................................ 1-2
Naval Sea Systems Command ..................................................................... 1-2
Space and Naval Warfare Systems Command (SPAWAR) ......................... 1-2
Bureau of Medicine and Surgery (BUMED) .................................................. 1-2
Commanding Officer ..................................................................................... 1-2
Ship and Shore Supervisory Personnel ........................................................ 1-3
Ship and Shore Operating Personnel ........................................................... 1-4
Personnel Training ....................................................................................... 1-4
Precautions to Ensure the Safety of Personnel ........................................... 1-5
Radio Frequency and Laser Overexposure Reporting Requirements ......... 1-6
Definitions and Abbreviations ...................................................................... 1-6
Reference Documents ................................................................................. 1-6
Biological Effects of Electromagnetic Radiation (EMR) and
Safe Exposure Limits ................................................................................... 1-6
Calculations and Measurements of Electromagnetic Fields ........................ 1-6
Reporting Omissions/Errors in Manual ........................................................ 1-7
CHAPTER 2 HAZARDS OF ELECTROMAGNETIC RADIATION TO PERSONNEL....... 2-1

2-1.
2-1.1
2-1.2
2-2.
2-2.1
2-2.2
2-2.3
2-2.4
Introduction .................................................................................................. 2-1

General ......................................................................................................... 2-1
Background................................................................................................... 2-1
EMR Hazards to Personnel ......................................................................... 2-1
Permissible Exposure Limits (PELs)............................................................. 2-1
Warning Signs, Devices, and Controls. ........................................................ 2-5
Calculated HERP Standoff Distances........................................................... 2-7
Radio Frequency Equipment Hazards. ......................................................... 2-7

TABLE OF CONTENTS (CONTINUED)
Chapter/Paragraph
2-2.5
2-2.6
Page
Aircraft Radar Hazards. ................................................................................ 2-8

HERP Standoff Distance Tables................................................................... 2-9
CHAPTER 3 RF BURNS ................................................................................................... 3-1

3-1.
3-2.
3-2.1
3-2.2
3-2.3
3-3.
3-3.1
3-3.2
3-3.3
3-3.4
3-3.5
3-3.6
3-3.7
Scope ........................................................................................................... 3-1

RF Burns from Cargo-Handling Equipment ................................................. 3-1
General. ........................................................................................................ 3-1
RF Burn Effects. ........................................................................................... 3-1
Electrical Characteristics of Metallic Objects. ............................................... 3-1
RF Burn Hazard Reduction Techniques ...................................................... 3-3
Introduction. .................................................................................................. 3-3
Limiting Body Contact Current...................................................................... 3-3
Hook Insulators............................................................................................. 3-3
Nonmetallic Materials. .................................................................................. 3-3
Antenna Relocation. ..................................................................................... 3-3
Operational Procedures................................................................................ 3-3
RF Radiation Hazard Warning Signs............................................................ 3-4
CHAPTER 4 BIOLOGICAL RADIATION HAZARD FROM LASER DEVICES ................ 4-1

4-1.
4-2.
4-3.
4-3.2
4-3.3
4-4.
4-5.
4-6.
4-7.
4-8.
Introduction .................................................................................................. 4-1

General Precautions Applicable to All Laser Installations ........................... 4-1
Laser Classification and Labeling ................................................................ 4-4
Military Exempt Lasers. ................................................................................ 4-4
Laser Range and Building Warning Signs. ................................................... 4-5
Training ........................................................................................................ 4-5
Medical Surveillance .................................................................................... 4-5
Command Laser Safety Program ................................................................ 4-5
Calculation of Laser Safe Distances and
Permissible Laser Exposure Levels ............................................................. 4-6
Laser Technical Assistance ......................................................................... 4-6
CHAPTER 5 IONIZING RADIATION................................................................................. 5-1

5-1.
5-2.
5-3.
5-4.
5-5.
5-6.
ii
Introduction .................................................................................................. 5-1

Units of Measurement .................................................................................. 5-1
Methods of Detecting Ionizing Radiation ..................................................... 5-1
Radiac Equipment ....................................................................................... 5-1
Hazard Level ................................................................................................ 5-2
Precautions .................................................................................................. 5-2

TABLE OF CONTENTS (CONTINUED)
Chapter/Paragraph
Page
CHAPTER 6 HAZARDS OF ELECTROMAGNETIC RADIATION TO FUEL.................... 6-1
6-1.
6-2.
6-3.
6-3.1
6-3.2
6-3.3
Introduction and Background ....................................................................... 6-1

Physical Nature of Combustion .................................................................... 6-1
Handling Precautions for Fuels in an RF environment ................................ 6-4
Introduction. .................................................................................................. 6-4
Fueling Precautions. ..................................................................................... 6-4
Transmitter Restrictions. ............................................................................... 6-5
APPENDIX A DEFINITIONS AND ABBREVIATIONS....................................................... A-1

APPENDIX B REFERENCE DOCUMENTS....................................................................... B-1
APPENDIX C BIOLOGICAL EFFECTS OF ELECTROMAGNETIC
RADIATION AND SAFE EXPOSURE LIMITS............................................ C-1
APPENDIX D CALCULATIONS AND MEASUREMENTS OF
ELECTROMAGNETIC FIELDS................................................................... D-1
iii

LIST OF FIGURES
FIGURE
TITLE
PAGE
2-1
2-2
RADHAZ Warning Sign Formats............................................................................. 2-4

Aircraft Radiation Patterns .................................................................................... 2-25
A/V-8B HARRIER ........................................................................................... 2-25
C-2 GRAYHOUND .......................................................................................... 2-26
C-9B SKYTRAIN ............................................................................................. 2-27
C-20 GULFSTREAM IV .................................................................................. 2-28
C-37 GULFSTREAM V ................................................................................... 2-29
C-40A CLIPPER (BOEING 737-700) .............................................................. 2-30
C-130 HERCULES .......................................................................................... 2-31
KC-130 HERCULES ....................................................................................... 2-32
E-2C HAWKEYE ............................................................................................. 2-33
E-6A MERCURY (TACAMO) .......................................................................... 2-34
EA-6B PROWLER .......................................................................................... 2-35
F-14 (ALL MODELS) ....................................................................................... 2-36
F/A-18 (ALL MODELS) ................................................................................... 2-37
P-3C ORION ................................................................................................... 2-38
P-3C ORION ................................................................................................... 2-39
P-3C ORION ................................................................................................... 2-40
S-3B VIKING ................................................................................................... 2-41
SH-60B SEAHAWK ........................................................................................ 2-42
T-39N SABERLINER ...................................................................................... 2-43
UC-12B HURON ............................................................................................. 2-44
UC-35 CITATION ............................................................................................ 2-45
V-22 OSPREY ................................................................................................ 2-46
3-1
4-1
4-2
6-1
6-2
6-3
Electrical Equivalent of Cargo-Handling Equipment................................................ 3-2

Laser Wavelength Chart ........................................................................................ 4-2
Military Laser Exemption Label .............................................................................. 4-5
Effect of Temperature in Generating Hydrocarbon Fuel Flammable Vapors ......... 6-2
Temperature-Flammability Ranges for Fuels ......................................................... 6-3
HERF Safe Separation Distance Calculation for MOGAS/AVGAS
(Radar and Communication Systems 225 MHz and Above)................................... 6-6
HERF Safe Separation Distance Calculation for MOGAS/AVGAS
(Communication Systems Below 225 MHz) ............................................................ 6-7
Graphic Representation of Permissible Exposure Limits in
Terms of Fields and Power Density for a Controlled Environment.......................... C-6
Graphic Representation of Permissible Exposure Limits in
Terms of Fields and Power Densityfor an Uncontrolled Environment..................... C-7
Calculation of Antenna Illumination Constant ......................................................... D-6
Fresnel Region Gain Correction for Uniform Illumination (Rectangular Aperture) . D-8
Fresnel Region Gain Correction for Cosine Illumination (Rectangular Aperture) ... D-9
6-4
C-1
C-2
D-1
D-2
D-3
iv

LIST OF FIGURES (CONTINUED)
FIGURE
D-4
D-5
D-6
D-7
D-8
D-8
D-9
D-9
D-10
D-11
D-12
D-13
D-14
TITLE
PAGE
Fresnel Region Gain Correction for Cosine Square

Illumination (Rectangular Aperture) ..................................................................... D-10
Fresnel Region Gain Correction for Cosine Cubed
Fresnel Region Gain Correction for Cosine Fourth
Normalized On-Axis Power Density Curves
Circular Aperture (1-r2) ..................................................................................... D-13
Sample On-Axis Power Density Computation for a
Rectangular Aperture Antenna (Sheet 1) ............................................................ D-16
Rectangular Aperture Antenna (Sheet 2) ............................................................ D-17
Circular Aperture Antenna (Sheet 1) ................................................................... D-18
Circular Aperture Antenna (Sheet 2) ................................................................... D-19
Functions of a Right Triangle ............................................................................... D-21
Sample Use of Trigonometric Functions for Solving Problems ........................... D-22
Power Gain Ratio Versus Decibel Gain ............................................................... D-26
Power Gain Ratio Versus dBm ............................................................................ D-29
Example of a Power Density Measurement ......................................................... D-34

LIST OF TABLES
TABLES
2-1
2-2
2-3
2-4
2-5
2-6
C-1
C-2
C-3
C-4
D-1
D-2
D-3
D-4
D-5
D-6
vi
TITLE
PAGE
Shipboard Communication and Satellite Systems .................................................. 2-10

Shore-Based Communication and Satellite Systems ............................................. 2-14
Shipboard Radar and Navigation Systems ............................................................. 2-18
Shore-Based Radar and Navigation Systems ........................................................ 2-21
Aircraft Radar Systems ........................................................................................... 2-23
Aircraft Radiation Patterns ...................................................................................... 2-24
PELs for Controlled Environments (Electromagnetic Fields) . . . . . . . . . . . . . . . . . C-2
PELs for Controlled Environments (Induced and Contact Current) . . . . . . . . . . . . . C-2
PELs for Uncontrolled Environments (Electromagnetic Fields) . . . . . . . . . . . . . . . C-4
PELs for Uncontrolled Environments (Induced and Contact Current) . . . . . . . . . . . C-4
Rectangular Apertures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-6
Circular Apertures with (1-r2) Illumination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-6
Circular Aperture Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-14
Rectangular Aperture Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-14
Decibel Table: Voltage, Current, and Power Ratios . . . . . . . . . . . . . . . . . . . . . . . D-25
dBm Conversion Table ...........................................................................................D-30

SAFETY SUMMARY
Volume 1 of this publication is a safety manual which discusses the hazards of
electromagnetic radiation (RF and laser) to personnel and fuel and approved methods or
procedures for minimizing accidents. Separate warnings or cautions are not contained herein
because the entire content is a warning to the user. However, notes are supplied in the text to
emphasize unusual or special procedures or conditions. Failure to observe operating
procedures and precautions specified in this manual may result in injury to personnel from RF
or laser radiation or the ignition of fuel.
vii/(viii Blank)

CHAPTER 1
INTRODUCTION
1-1.
PURPOSE AND SCOPE OF MANUAL
1-1.1 This manual consists of two unclassified volumes to provide the data necessary for the
protection of personnel, fuels, and ordnance from radio-frequency (RF) energy (including laser
devices). Volume 1 discusses the Hazards of Electromagnetic Radiation to Personnel (HERP)
and the Hazards of Electromagnetic Radiation to Fuels (HERF) and other flammable materials.
Volume 2 discusses the Hazards of Electromagnetic Radiation to Ordnance (HERO).
1-1.2 Both volume 1 and volume 2 address the standoff distances from shipboard and shorebased transmitters required to satisfy HERP and HERO (respectively) safety criteria. In
addition, the radiation patterns and safe standoff distances from Navy/Marine Corps aircraft
radars are illustrated
1-1.3 This manual shall be used by the following types of naval activities:
Marine Corps Air Stations
Marine Corps Bases
Naval Air Facilities
Naval Air Stations
Naval Air Warfare Centers
Naval Computer and Telecommunications Facilities
Naval Laboratories
Naval Magazines
Naval Missile Ranges
Naval Ordnance Facilities
Naval Ships
Naval Shipyards
Naval Stations
Naval Surface Warfare Centers
Naval Systems Commands
Naval Weapons Stations
Submarine Support Facilities
1-2.
BACKGROUND
1-2.1 RF HAZARDS TO PERSONNEL. Radiation from antennas fed by high-powered RF

transmitters has the potential for injuring personnel present in the vicinity of the radiating
antennas. Transmitters aboard ships, on aircraft, and at shore stations are potential sources of
harmful radiation. At some frequencies, exposure to excessive levels of RF radiation will not
produce a noticeable sensation of pain or discomfort to give warning that injury may be
occurring. Radiated energy can also result in high levels of induced and contact current
1-1

through the body when in close proximity to high-power RF transmitting antennas below
100 MHz. RF hazards to personnel, permissible exposure limits, and an explanation of induced
and contact currents are contained in chapter 2. RF burns are discussed in chapter 3.
1-2.2 LASER HAZARDS TO PERSONNEL. Laser radiation of high intensity, if absorbed by
the body or eyes, may result in permanent damage. The details for laser operation, safety
precautions, and safe exposure levels are contained in chapter 4.
1-2.3 IONIZING RADIATION. Ionizing radiation sources, hazard levels, and safety
precautions are discussed in chapter 5.
1-2.4 RF HAZARDS TO FUEL. Study and research are continuing to (1) provide safe
handling distances for fuel and (2) eliminate conditions conducive to arcing during fuel handling.
Procedures to reduce the possibility of fuels being ignited by RF radiation-induced arcing are
provided in chapter 6.
1-2.5 RF HAZARDS TO ORDNANCE. Electroexplosive devices, electrically initiated
devices, and ordnance electrical systems may be affected when exposed to RF energy. The
Naval Sea Systems Command (NAVSEA) Program Executive Office sponsors testing programs
to determine weapon susceptibility to RF energy. Tests are conducted in the maximum RF
environments to which ordnance items may be exposed during a typical stockpile-to-launch
scenario. An affected system or item might have sufficient current induced by the RF field to
result in premature firing, explosion, or dudding. A listing of all Navy and Marine Corps
ordnance with HERO concerns is contained in Volume 1.
1-3.
RESPONSIBILITIES
1-3.1 NAVAL SEA SYSTEMS COMMAND. NAVSEA, in accordance with Chief of Naval
Operations directives, exercises technical direction over fleet personnel safety and is
responsible for shipboard HERP- and HERF-related data and issues. As part of NAVSEA,
Naval Ordnance Safety and Security Activity, N716, is responsible for all HERO-related data
and safety of ammunition, explosives, and other hazardous materials in the fleet and shore
establishments.
1-3.2 SPACE AND NAVAL WARFARE SYSTEMS COMMAND (SPAWAR). SPAWAR is
responsible for shore facility HERP- and HERF-related data and issues.
1-3.3 BUREAU OF MEDICINE AND SURGERY (BUMED). BUMED is responsible for
adopting scientifically established personnel exposure levels for electromagnetic and laser
radiation, reviewing personnel overexposures, and providing appropriate medical
recommendations.
1-3.4 COMMANDING OFFICER. In addition to the duties and responsibilities inherent in the
position of commanding officer as set forth in Navy regulations or as promulgated by higher
authority, the commanding officer of a ship or naval shore station is solely responsible for the
safety of his/her command. He/she must take the same active, aggressive leadership in safety
1-2

that he/she takes in other phases of command responsibility. It is the commanding officers
responsibility to require personnel of other agencies, including contractors, while on board ship
or at a facility under his/her command, to conduct their activities in accordance with established
safety rules. The commanding officer shall enforce the mandatory requirements of this manual
and shall initiate those directives and inspections necessary to evaluate compliance with the
rules and regulations prescribed herein. The absence of a safety requirement in this manual, or
in the documents referenced herein, does not necessarily indicate that safeguards are not
required. Commanding officers have the authority to impose and enforce more stringent safety
rules than those imposed by higher authority. Where no existing safety rule or regulation
applies, or where a deviation from an established mandatory safety regulation is desired, the
commanding officer shall submit to Commander, NAVSEA, Code 53H, full particulars and
detailed plans for approval. In the interim, the commanding officer shall take the necessary
action to control the hazard. Shipboard commanders may waive compliance with any provision
of this manual when essential under emergency conditions.
1-3.5 SHIP AND SHORE SUPERVISORY PERSONNEL. Supervisors shall be thoroughly
familiar with the provisions of this publication. Supervisors have no authority to waive or alter
NAVSEA and station safety regulations, nor shall they permit the violation of such safety
regulations by others. They shall act positively to eliminate any potential accident hazards
existing in operations under their jurisdiction. Aboard ship, supervisory personnel must perform
the functions of shore station safety directors. Each supervisor shall also comply with the
following regulations:
a. Explain to all personnel under his/her immediate supervision the standard safety
regulations, industrial hygiene safeguards, and precautions that they must follow and enforce
regarding the observance of all safety regulations by personnel. The supervisor shall explain
the safe distances as they apply to RF energy and lasers.
b. Instruct and train personnel under his/her immediate supervision in the work that they
are to perform, whether instruction is given directly or through experienced operators, until the
supervisor is satisfied that all personnel are capable of performing the work safely. This
instruction shall also encompass complete information concerning transmitter location,
identification, adherence to all RF and laser warning signs and placards, and observance of all
safety circles and other safety zones.
c. Ensure that personnel are qualified and certified to perform the job assigned and that
such certification is current. Report promptly to his/her immediate superior all personnel who, in
his/her opinion, are not qualified for their assigned work.
d. Investigate or assist in the investigation of all accidents involving operations,
equipment, or personnel under his/her supervision, and report or assist in the preparation of the
report on the investigations results to higher authority for appropriate action.
e. Identify all persons entering or approaching a radiation hazards (RADHAZ) area in
his/her charge, and determine their authority to enter and/or remain in the area. Exercise his/
1-3

her authority to eject any person whose presence and/or actions, in his/her opinion, are
detrimental to safety.
f. Forbid any major repairs or modification to any transmitting equipment except in
accordance with specific instructions of the commanding officer. Enforce the safety
requirements in his/her area.
g. Ascertain that all conditions in the area under his/her jurisdiction comply with orders
relating to operation shutdown. When the operation is not relieved by an incoming shift, the
supervisor shall make certain that all transmitters are shut off. When an incoming shift relieves
his/her operation or he/she is relieved for any reason, the supervisor shall make a complete
report to the relief of any situation that requires immediate attention or which should be kept
under observation.
h. Enforce observance of the safety regulations concerning personnel protective
clothing and equipment.
i. Report in writing to his/her commanding officer any requests, suggestions, and
comments he/she may have with regard to safety standards.
1-3.6 SHIP AND SHORE OPERATING PERSONNEL. Operating personnel are responsible
for understanding and strictly observing all safety standards, requirements, and precautions
applicable to their work or duty. In addition, each individual will:
a. Report to his/her supervisor any unsafe condition, personnel actions, or any
equipment or material that he/she considers unsafe.
b. Warn others whom he/she believes to be endangered by known hazards or by failure
to observe safety precautions.
c. Wear or use approved protective clothing or equipment when required.
d. Report to his/her supervisor any injury or evidence of impaired health to himself/
herself or others occurring in the course of work or duty.
e. Be prepared, in the event of an unforeseen hazardous occurrence, to give an audible
warning to the other employees and to exercise such reasonable caution as is appropriate to
the situation.
f. Report the presence of unauthorized personnel in the work area to his/her supervisor.
1-4.
PERSONNEL TRAINING
1-4.1 All personnel engaged in operations involving the use of RF transmitting equipment or
laser devices shall be familiar with all phases of work which they will be required to perform.
Included in their training will be instruction in the following:
1-4

a. RF and laser radiation hazards.
b. Sources of RF burns.
c. Detection of faulty transmitters or related equipments.
d. RADHAZ warning signs, devices, and controls.
e. Electrical characteristics of metallic objects.
f. Sources of RF hazards.
g. The characteristics of modified or new RF transmitting equipment.
h. Use of protective equipment.
i. Use of OPNAVINST 5100.23 (series), OPNAVINST 5100.19 (series), and this
manual.
1-4.2 Films dealing with RF hazards are available for training purposes through regular
channels. Film identification number for the series titled "Radio Frequency Radiation Hazards"
is MN9682. Individual films in this series are as follows:
a. MN9682a - Radio Frequency Radiation Hazards - RF Hazards and Personnel Safety.
b. MN9682d - Radio Frequency Radiation Hazards - RF Burns, Causes and Effects.
1-5.
PRECAUTIONS TO ENSURE THE SAFETY OF PERSONNEL
It is the responsibility of the commanding officer of each ship or shore station to

implement the requirements contained in this manual, including the following:
a. Ensure that procedures are established whereby RF transmitting equipment is
positively controlled and coordinated with personnel working near antennas, handling
ordnance, and conducting fueling operations. Procedures for controlling laser operations also
shall be generated.
b. Ensure that RF hazards associated with the operation of laser and radar transmitters
(in both controlled and uncontrolled environments) are known to all personnel, and that the
necessary safety precautions are implemented. See paragraph 2-2.1.2, for the definition of
controlled and uncontrolled environments.
c. Have RF RADHAZ surveys conducted to determine the appropriate safety
precautions for personnel and for operations involving fuel and ordnance. Requests for RF
hazard surveys and information relating to shipboard HERP and HERO, or shore facility HERO,
should be mailed to Commander, Dahlgren Division, Naval Surface Warfare Center,
1-5

J52/R. Needy, 17320 Dahlgren Road, Dahlgren, VA 22448-5100, or forwarded electronically to
needyri@nswc.navy.mil. Requests may also be made by calling (540) 653-3446/8594 or DSN
249-3446/8594.
Requests for RF hazard surveys or information relating to shore facility HERP should be
mailed to Space and Naval Warfare Systems Command, Code 323/W. Hammer, P.O. Box
19022, North Charleston, SC 29419-9022, or forwarded electronically to
hammerw@spawar.navy.mil. Requests may also be made by calling (843) 218-4876.
Requests for laser system evaluations or range surveys should be submitted as
described in paragraph 4-8, of this document.
d. Ensure that HERP, HERF, HERO, and laser considerations are included in all
proposed changes to station or facility operations.
1-6.
RADIO FREQUENCY AND LASER OVEREXPOSURE REPORTING REQUIREMENTS
Report all RF overexposure incidents in accordance with the requirements of

OPNAVINST 5100.19 (series) for ship personnel and OPNAVINST 5100.23 (series) for shore
personnel. Report laser overexposure incidents as per OPNAVINST 5100.27/MCO 5104.1
(series) and BUMEDINST 6470.23 (series).
1-7.
DEFINITIONS AND ABBREVIATIONS
The definitions of the terms and the meaning of the abbreviations used are listed in
appendix A.
1-8.
REFERENCE DOCUMENTS
A list of reference documents applicable to this volume is presented in appendix B.

These documents, together with ship and station instructions and notices, technical
publications, and standard operating procedures shall be maintained in appropriate libraries.
These documents are essential for complete understanding of the safety regulations contained
herein.
1-9. BIOLOGICAL EFFECTS OF ELECTROMAGNETIC RADIATION (EMR) AND SAFE
EXPOSURE LIMITS
Appendix C describes the biological effects of EMR on the human body and the limits to
which the body can be safely exposed.
1-10. CALCULATIONS AND MEASUREMENTS OF ELECTROMAGNETIC FIELDS
The electromagnetic environment, the method for calculating power density in an
electromagnetic field, and calculation aids for use in predicting RF radiation hazards are
described in appendix D.
1-6

1-11. REPORTING OMISSIONS/ERRORS IN MANUAL
Ships, training activities, supply points, depots, Naval shipyards, and supervisors of
shipbuilding are requested to arrange for the maximum practical use and evaluation of NAVSEA
technical manuals. All errors, omissions, discrepancies, and suggestions for improvement to
NAVSEA technical manuals shall be reported to the Commander, Naval Surface Warfare
Center, Port Hueneme Division (NSWC/PHD) (Code 5E31), 4363 Missile Way, Port Hueneme,
CA 93043-4307 on NAVSEA Technical Manual Deficiency/Evaluation Report (TMDER),
NAVSEA Form 4160/1. A copy of NAVSEA TMDER Form 4160/1 is included at the end of this
publication. For activities with internet access, this form may also be completed and processed
using NSWC/PHD website: http://nsdsa.phdnswc.navy.mil. All feedback comments shall be
thoroughly investigated and originators will be advised of TMDER resolution. If you prefer to
submit a TMDER using a word file, click here
TMDER
1-7/(1-8 Blank)

CHAPTER 2
HAZARDS OF ELECTROMAGNETIC RADIATION TO PERSONNEL
2-1.
INTRODUCTION
2-1.1 GENERAL. This chapter discusses the hazards of electromagnetic radiation to

personnel (HERP), as well as the means by which such radio-frequency (RF) hazards may be
mitigated. Electromagnetic radiation (EMR), as discussed in this section, is referred to as
nonionizing radiation, a form of radiation that does not have sufficient energy to cause ionization
of atoms or molecules. Electromagnetic emissions from laser, radar, communication, and
microwave sources are examples of nonionizing radiation.
Also included in this chapter is a list of personnel safe distances associated with
currently operational Navy aircraft, as well as shipboard and shore-based RF transmitters. In
the case of aircraft, the radiation pattern of the installed radar system is also provided. The
biological hazards associated with electromagnetic (RF) radiation [as established by the
Institute of Electrical and Electronics Engineers (IEEE) C95.1 Standards Committee, adopted
by the Tri-Service Electromagnetic Radiation Panel, and presented in Department of Defense
Instruction (DODINST) 6055.11] are discussed in appendix C. As technical agent for Naval Sea
Systems Command (NAVSEA), Naval Surface Warfare Center, Dahlgren Division, Dahlgren,
Virginia, is responsible for identifying potentially hazardous shipboard areas. Space and Naval
Warfare Systems Command (SPAWAR), Charleston, South Carolina, is responsible for
identifying potential hazardous shore facility areas and for ensuring that controls necessary to
prevent biological injury to personnel are defined and implemented.
2-1.2 BACKGROUND. Radar and communication systems which use high-power RF
transmitters and high-gain antennas represent a biological hazard to personnel working on, or
in the vicinity of, these systems. The detrimental effects of overexposure to EMR are
associated with an increase in overall body temperature or a temperature rise in specific organs
of the body.
2-2.
EMR HAZARDS TO PERSONNEL
2-2.1 PERMISSIBLE EXPOSURE LIMITS (PELS).

2-2.1.1 DODINST 6055.11 lists safe limits based upon established biological effects due to RF
radiation (RFR) exposure over the frequency range of 3 kHz to 300 GHz. The biological effects
have been determined to be a function of the specific absorption rate (SAR), which is frequency
dependent and averaged over a 6-minute time period. A more detailed discussion of PELs and
SARs is presented in appendix C.
2-1

2-2.1.2 Exposure limits are specified for locations that are defined as either controlled or
uncontrolled environments. Controlled environments are areas (designated shipboard work/
equipment spaces, shipboard weather decks, and topside areas) where exposure to higherthan-normal levels of electromagnetic energy may be incurred by personnel who are aware of
the potential for such exposure. Uncontrolled environments include public areas, living
quarters, and work spaces where there is no expectation that higher electromagnetic
environments should be encountered. Shore facilities will typically have a combination of
controlled and uncontrolled environments, as defined by each command. A more detailed
discussion of exposure limit guidelines is provided in appendix C. However, since these
guidelines require further explanation and are subject to change, DODINST 6055.11 (series)
should be consulted by persons responsible for conducting RF hazard analyses.
2-2.1.3 The exposure limits for controlled environments represent scientifically derived values
to limit absorption of electromagnetic energy in the body and to restrict the magnitude of
currents induced in the body. As a result, the amount of RF energy absorbed is insufficient to
produce or cause any adverse health effects, even under repeated or long-term exposure
conditions. The controlled environmental limits are the equivalent of personnel exposure
standards for all individuals. In uncontrolled environments where access is not restricted or
controlled, lower permissible RF exposure levels have been adopted. The reduced exposure
limits permitted in uncontrolled environments reflect a consensus to minimize exposure levels
outside well-defined areas and should not be interpreted as a disregard for any known adverse
health risk. There are no shipboard topside environments defined as uncontrolled
environments; therefore, this condition/situation is not discussed in detail in this report. For
shore facilities, uncontrolled areas are determined by the local command authority.
2-2.1.4 In those cases where personnel in a controlled environment must be exposed to power
densities greater than the continuous PEL, the use of time averaging may be employed to
determine the safe stay-time. Intermittent (vice continuous) exposure times can be calculated
as described in paragraph C-5 and in DODINST 6055.11.
2-2.1.5 Induced and Contact Currents. Induced and contact current exposure limit guidelines
for controlled and uncontrolled environments are provided in tables C-2 and C-4, respectively.
However, since these guidelines require further explanation and are subject to change,
DODINST 6055.11 should be consulted by persons responsible for conducting hazard
assessments.
2-2.1.6 Induced Current PEL. When a person is freely standing (not grasping a conductive
object) in a radiated field, RF currents are induced into the body. As those induced currents
flow between the human body and ground, heat is produced, particularly in the constricted area
of the ankles. For frequencies between 100 kHz and 100 MHz, current induced through the feet
in a controlled environment is limited to 100 mA if measured through one foot, or 200 mA if
measured through both feet. The 200-mA limit through both feet assures that localized SARs
will not exceed the 20-W/kg limit for extremities.
2-2.1.7 Contact Current PEL. Contact current, or "grasping contact" current, is the current
which flows through the hand(s) when a person grasps a conductive object while in a radiated
2-2

field. The contact current (PEL) in a controlled environment is 100 mA for the hand in contact
with the ungrounded surface. This limit provides assurance that the 20-W/kg extremities limit
will not be exceeded.
The present procedure for measuring this limit of contact or "grasping contact" current for
the shipboard and shore radiation hazards (RADHAZ) survey is to measure only those items
which are grasped during their normal operation or use, such as life lines or rails. Currently, a
Type 3 RADHAZ warning sign (RF Burn) is posted in the vicinity of these items to denote a
contact-current hazard. For items which are grasped during normal operations (e.g., signal
lights), Type 5 warning signs are used to provide specific control measures. RADHAZ warning
sign formats are shown in figure 2-1.
2-2.1.8 RF Burn Criteria. The nature of RF burns, how they occur, and procedures for
minimizing their effects are contained in chapter 3 of this document, from which the following
excerpt is extracted:
An RF burn is the result of RF current flow through that portion of the body in direct contact
with a conductive object (in which an RF voltage has been induced) or at the site of a spark
discharge (no direct contact with a conductive object). Any burn injury that occurs is entirely
the result of heat produced by current flow through the resistance of the skin. Current flow
through a resistance produces heat regardless of the nature of the circuit.
As discussed in chapter 3, the established criteria is that an open-circuit voltage
exceeding 140 volts on an item in an RFR field is to be considered potentially hazardous. The
effect of the heat on a person ranges from warmth to painful burns. However, field tests have
shown that, because of the many variables involved, it is not uncommon to encounter
significantly higher voltages that will not cause an RF burn. The term "hazard" can range from
visible skin damage to a shock sensation. The specific level at which contact with RF voltages
should be classified an RF burn hazard is not a distinct one; however, 140 volts is recognized
as the PEL, and a Type 3 RADHAZ warning sign (RF Burn) is posted in the vicinity of these
items to denote an RF burn hazard. RADHAZ warning sign formats are shown in figure 2-1.
2-2.1.9 NAVSEA, Code 53H, is responsible for determining hazardous shipboard areas and
ensuring that the possibility of biological injury to personnel from RF radiation is minimized or
eliminated. Theoretical calculations and RF field-intensity and power-density measurements
are used to establish the safe distances from radar antennas. This information is then used to
determine whether or not hazardous shipboard areas exist. Radiation inhibit zones are used to
minimize the number of hazardous areas. Appropriate warning signs, warning instructions,
and/or markings shall be posted in all hazardous areas subject to entry by personnel.
2-2.1.10 For shipboard situations, weather decks, enclosed and open masts, and electronic
work spaces (at a minimum) should be considered controlled environments. For shore stations,
accessible areas beyond the stations perimeter fence lines (at a minimum) should be
considered uncontrolled environments.
2-3

FIGURE 2-1. RADHAZ Warning Sign Formats
2-4

2-2.1.11 No special RF exposure limits or additional RF exposure restrictions are imposed in
the case of pregnancy.
2-2.2 WARNING SIGNS, DEVICES, AND CONTROLS.
2-2.2.1 RADHAZ Warning Signs. RADHAZ warning signs have been developed to advise
personnel of the hazards of EMR. The format of these signs conforms with national and
international standards. The RADHAZ warning sign formats are provided, along with the
National Stock Numbers, in figure 2-1.
2-2.2.2 Variations, to include subdued signs for camouflage or tactical reasons, or to provide
improved visibility under certain lighting conditions, are authorized, provided the general layout
of the sign remains the same.
2-2.2.3 When required by military operational considerations, commanders may waive the
requirement for signs, provided personnel are informed of possible hazards by other means.
2-2.2.4 Type 1 Warning Sign. The Type 1 warning sign advises personnel of an RF hazard
and shall be posted at the boundary (PEL line) of an area, beyond which the PEL may be
exceeded (see paragraph 2-2.2.9). Personnel may pass through this area but must not linger.
If personnel are required to remain in the area, they must contact the cognizant command
authority, who will ensure that procedures are implemented to limit RF exposure to a level
below PEL. Type 1 warning signs shall never be posted in an area undefined by a PEL line.
2-2.2.5 Type 2 Warning Sign. The Type 2 warning sign excludes personnel from proceeding
past a designated point. The sign informs personnel to check with command authority before
proceeding beyond this point. This sign is normally posted at access points to RADHAZ
restricted zones, such as masts and high-power antenna platforms, and in the vicinity of
normally occupied areas which have RADHAZ barriers or personnel barriers to restrict access.
2-2.2.6 Type 3 Warning Sign. The Type 3 warning sign informs personnel that contact current
and/or RF burn hazards may exist on metallic objects in this area. The Type 3 sign is used to
denote RF hazards due to contact with metallic objects in the area and is normally posted on
the metallic object that presents the worst hazard. Personnel should be aware that this hazard
may also exist on other metallic objects in the area. An RF burn hazard may exist when either
the RF voltage or contact current PEL is exceeded. Additional RADHAZ control measures (i.e.,
Type 5 RADHAZ sign) may be required to ensure that this hazard is limited to levels that do not
exceed the PEL on metallic objects that personnel must grasp, such as signal lights and
binoculars.
2-2.2.7 Type 4 Warning Sign. The Type 4 warning sign informs personnel that an RF hazard
exists and to check with command authority prior to fueling operations. Further instructions are
then provided that may include limitation on transmitter power or silence of specific transmitting
antennas. This sign is usually placed next to a fuel storage and/or refueling station.
2-5

2-2.2.8 Type 5 Warning Sign. The Type 5 warning sign provides a blank area in which special
instructions necessary for safe operations can be specified. Often, the sign provides operators
and maintenance personnel with specific frequency and/or power limitation information for the
safe operation of the antenna systems associated with the RF transmitting equipment. The
Type 5 sign may also be used to inform personnel to contact command authority prior to
operation of equipment in order to prevent an RF hazard to the operator or other personnel.
The Type 5 sign should be posted in clear view of system operators.
2-2.2.9 PEL Line. A PEL line is used to mark a deck area where precautionary measures are
required to minimize the possibility of personnel exposure to RFR in excess of the PEL. The
PEL line is a 4-inch-wide red line (usually a circle or semicircle) painted on the deck to mark the
boundary of an area surrounding an antenna where the PEL can be exceeded. When a PEL
line is used, a Type 1 RADHAZ warning sign is posted on the PEL line to advise personnel that
a hazard may exist and that they must keep moving. Personnel outside the PEL line need not
take precautionary measures; however, when it is necessary for personnel to be within the
marked areas, they must contact appropriate personnel who will ensure that operational
procedures are implemented to limit RF exposure to a level below the PEL.
2-2.2.10 Red Warning Bands. A red warning band is used to mark a safety rail or life rail
where precautionary measures are required in order to minimize the possibility of exposure to
contact currents in excess of the PEL. The red warning band is a 4-inch-wide red line painted
on the top of the safety rail to mark the boundary of an area in proximity to an antenna where
the PEL can be exceeded. Where a red warning band is used, a Type 3 RADHAZ warning sign
is posted to advise personnel that an RF burn hazard may exist. In those cases where further
information or clarification is required, a Type 5 RADHAZ sign should be used.
2-2.2.11 Personnel Barriers. In areas where access to levels greater than 10 times the
exposure limits for controlled environments may exist, warning signs alone do not provide
sufficient protection. Devices such as flashing lights, audible signals, barriers, and/or interlocks
shall be installed to prevent inadvertent access. The specific device(s) employed will be
determined by the certifying authority based on the potential for exposure.
Personnel barriers are devices that restrict personnel access to an antenna or area
where the PEL can be exceeded. The personnel barrier may be a fixed one, such as a
permanent fenced area around an antenna. If no access to the antenna is provided, personnel
barriers are not required. If there is an access opening, a temporary barrier (i.e., nylon rope)
may be used to restrict personnel access. In this case, a Type 2 warning sign is also posted on
a placard, which is normally attached to the nylon rope.
2-2.2.12 Frequency and/or Power Management. Frequency and/or power management
restrictions may be employed to ensure that personnel are not exposed to RF energy in excess
of the authorized PEL. Such restrictions may be imposed to limit RF exposure within a
RADHAZ area defined by PEL lines, or to limit RF contact current on items that personnel are
required to grasp while performing their assigned task. The HERP/Hazards of Electromagnetic
Radiation to Fuel (HERF) Technical Report (prepared following a HERP/HERF survey) provides
2-6

specific guidance and recommended operating procedures to manage potential RF hazards.
These procedures may include one or more of the following:
a.
Refrain from using the antenna.
b.
Reduce power for the frequencies at which the PEL is exceeded.
c.
Refrain from using frequencies at which the PEL is exceeded.
Type 5 warning signs are used to provide operator or maintenance personnel with the
frequency and/or power management requirements.
2-2.3 CALCULATED HERP STANDOFF DISTANCES. The HERP standoff distances listed in
table 2-1 and table 2-4 are considered to be those distances from a transmitting antenna where
the radiated field intensity is equal to the continuous exposure (whole body) PEL for controlled
environments specified in DODINST 6055.11 (series). The standoff distances were calculated
using power density modeling programs developed by NAVSEA and based upon currently
available system electrical specifications. In most cases, these calculated distances are based
upon worst-case conditions as no system installation losses were considered.
NOTE
While phased-array antenna systems do not physically rotate, their moving
beam characteristics are equivalent to rotating-beam systems.
2-2.3.1 The HERP standoff distances noted in tables 2-1 through 2-4 are based on the
assumption that the specified system uses a fixed (nonrotating) antenna. However, with the
exception of communication systems (i.e., HF, VHF, UHF, and satellite systems), most
shipboard and land-based radar systems use rotating-beam antennas. Typically, there will be
no HERP concerns (hazards) associated with rotating-beam systems, since the intermittent
exposure time per radar sweep will result in exposures which do not exceed the continuousexposure PEL. However, since rotating-beam systems may be operated in a fixed mode during
certain evolutions, it is essential that personnel be aware of the potential hazards associated
with this mode of operation.
2-2.4 RADIO FREQUENCY EQUIPMENT HAZARDS.
2-2.4.1 Tables 2-1 through 2-5 list the most common shipboard, shore-based, and aircraft RF
transmitters capable of producing potentially harmful levels of EMR. The HERP standoff
distances specified in these tables are based on the PELs for controlled environments that
appear in appendix C. The information was modified (where noted) by actual measurements
obtained during shipboard or shore-station RF surveys. Requests for assistance in making
such measurements for ship equipment should be directed to Commander, Dahlgren Division,
Naval Surface Warfare Center, J52/R. Needy, 17320 Dahlgren Road, Dahlgren, VA
22448-5100, (540) 653-3446/8594 or DSN 249-3446, or forwarded electronically to
needyri@nswc.navy.mil. Requests pertaining to shore-based equipment should be directed to
2-7

Space and Naval Warfare Systems Command, Code 323/W. Hammer, P.O. Box 19022,
Charleston, SC 29419-9022, (843) 218-4876 or DSN 588-4876, or forwarded electronically to
hammerw@spawar.navy.mil.
2-2.4.2 Before personnel are exposed to RF energy from radar and/or communication
equipment not listed in tables 2-1 through 2-5, the HERP safe standoff distance shall be
determined. This information is normally contained in the commands HERP survey.
The HERP certification survey for modified or newly installed shipboard equipment shall
be obtained by contacting Commander, Dahlgren Division, Naval Surface Warfare Center, J52/
R. Needy, 17320 Dahlgren Road, Dahlgren, VA 22448-5100, (540) 653-3446/8594 or DSN
249-3446, or via e-mail (needyri@nswc.navy.mil). For information pertaining to shore-based
equipment, contact Space and Naval Warfare Systems Command, Code 323/W. Hammer, P.O.
Box 19022, Charleston, SC 29419-9022, (843) 218-4876 or DSN 588-4876, or via e-mail
(hammerw@spawar.navy.mil).
2-2.4.3 Operational and/or maintenance requirements that expose personnel to RF
environments in excess of the (controlled environment) PELs appearing in appendix C may be
permitted using time-averaging (vice continuous-exposure) criteria. Because of the complexity
of this calculation, the recommended procedure for shipboard equipment is to contact
Commander, Dahlgren Division, Naval Surface Warfare Center, J52/R. Needy, 17320 Dahlgren
Road, Dahlgren, VA 22448-5100, (540) 653-3446/8594 or DSN 249-3446, or via e-mail
(needyri@nswc.navy.mil). For information pertaining to shore-based equipment, contact Space
and Naval Warfare Systems Command, Code 323/W. Hammer, P.O. Box 19022, Charleston,
SC 29419-9022, (843) 218-4876 or DSN 588-4876, or via e-mail (hammerw@spawar.navy.mil).
2-2.5 AIRCRAFT RADAR HAZARDS.
2-2.5.1 Table 2-5 lists the PEL and HERP fixed-beam standoff distances associated with the
aircraft radar systems specified. Figure 2-2 depicts the radiation patterns and HERP safe
separation distances associated with these systems. Many of the listed aircraft are equipped
with landing-gear interlock (weight-on-wheels) switches which make it impossible to energize
the radar transmitter until one or more deliberate actions have been taken. All personnel who
operate or work in the vicinity of aircraft radar transmitters on deck shall be familiar with the
RADHAZ zones around the aircraft. Maintenance personnel who bypass such safety interlocks
shall ensure that safety zones are established and that personnel are alerted to the potential
hazard. Maintenance personnel shall also ensure that interlock bypass switches are returned
to their normal positions at the completion of maintenance.
2-2.5.2 Unlike most shipboard and land-based systems, aircraft radars do not typically rotate.
Rather, such systems scan (sweep) the airspace to the left and right of the aircraft centerline. In
most cases, the scan can be narrowed by the operator to just a few degrees either side of
center. Therefore, for airborne radars, the HERP fixed-beam standoff distance and scan limits
specified in table 2-5 and figure 2-2 should always be maintained during ground radar
operation.
2-8

2-3.
HERP STANDOFF DISTANCE TABLES
The HERP standoff distances appearing in tables 2-1 through 2-5 are based on the PELs
for controlled environments that appear in appendix C. Since the system operating
characteristics (frequency, average power, effective radiated power) required to calculate HERP
standoff distances are often classified, this information has not been included in tables 2-1
through 2-5.
Because a given communication system may employ a variety of antennas (monopole,
dipole, Yagi, log periodic, etc.), reference to a specific antenna type has been omitted from
tables 2-1 and 2-2. Instead, antenna gain information has been provided to aid in determining
the appropriate safe standoff distance for a particular communication system.
2-9

Table 2-1. Shipboard Communication and Satellite Systems
TRANSMITTER NAME
ANTENNA GAIN
(dBi)
PEL
(mW/cm2)
HERP SAFE
STANDOFF DISTANCE
(Meters)
(Feet)
ROTATING
BEAM
HAZARD
N/A
8400 STD
2.1
1.00
0.6
AN/ARC-159
2.1
0.75
0.9
N/A
AN/ARC-182
2.1
1.00
0.6
N/A
AN/ARC-182(V)
3.0
1.00
0.9
N/A
AN/GRC-171
2.1
1.00
0.9
N/A
AN/GRC-211
2.1
1.00
0.9
N/A
AN/GRC-226(V)4
2.1
4.50
0.3
N/A
AN/GRT-21(V)
2.1
1.00
0.9
N/A
AN/MRC-142
28.0
4.50
1.8
N/A
AN/PRC-113(V)
2.1
1.00
0.6
N/A
AN/PRC-117F
2.1
1.00
1.8
N/A
AN/PRC-119A
1.0
1.00
0.3
N/A
AN/PSC-3
6.0
1.00
0.9
N/A
AN/PSC-5
3.0
1.00
0.6
N/A
AN/SRC-22(V)
2.1
1.00
0.3
N/A
AN/SRC-40
2.1
1.00
0.3
N/A
AN/SRC-41
2.1
1.10
0.3
N/A
1.0
1.10
0.3
N/A
2.1
1.10
0.3
N/A
0.0
1.00
0.9
N/A
2.1
1.00
0.9
N/A
2.1
1.00
0.9
N/A
2.1
1.30
0.6
N/A
5.1
1.30
0.9
N/A
AN/SRC-47(V)
AN/SRC-54
AN/SRC-54B
AN/SRC-55
AN/SRC-57
AN/SRQ-4
AN/SRQ-4A
0.0
4.50
0.6
N/A
Classified
10.00
0.3
N/A
Classified
10.00
2.1
N/A
Classified
10.00
0.1
N/A
Classified
10.00
2.1
N/A
AN/TSC-93
43.5
10.00
94.5
310
N/A
AN/TSC-93B
42.5
10.00
84.1
276
N/A
AN/TSQ-129
6.0
1.40
1.5
N/A
AN/URC-100
2.1
1.00
0.3
N/A
AN/URC-101
2.1
1.00
0.3
N/A
AN/URC-107B
2.1
3.20
0.9
N/A
2.1 (2-9 MHz)
11.10
1.2
N/A
2.1 (9-30 MHz)
1.00
3.7
12
N/A
2.1 (2-30 MHz)
1.00
3.7
12
N/A
AN/URC-109 (Series)
2-10

TRANSMITTER NAME
AN/URC-131 (Series)
AN/URC-139
ANTENNA GAIN
(dBi)
PEL
(mW/cm2)
HERP SAFE
STANDOFF DISTANCE
(Meters)
(Feet)
ROTATING
BEAM
HAZARD
N/A
2.1 (2-9 MHz)
11.10
5.2
17
2.1 (9-30 MHz)
1.00
5.2
17
N/A
2.1 (2-30 MHz)
1.00
3.7
12
N/A
0.0
1.00
0.6
N/A
2.1
1.00
0.6
N/A
AN/URC-139(V)
2.1
1.00
0.6
N/A
AN/URC-80(V)5
2.1
1.00
0.6
N/A
AN/URC-80(V)6
2.1
1.00
0.6
N/A
AN/URC-86
2.1
1.00
0.6
N/A
1.7
1.00
0.9
N/A
2.1
1.00
1.2
N/A
2.1
1.00
1.2
N/A
AN/URC-93(V)1
AN/URC-93(V)2
5.0
1.00
1.8
N/A
AN/URC-93A(V)1
2.1
1.00
0.9
N/A
AN/URC-94
0.0
1.00
0.9
N/A
2.1 (2-6 MHz)
25.00
0.9
N/A
2.1 (2-30 MHz)
1.00
3.7
12
N/A
2.1 (10-30 MHz)
1.00
3.7
12
N/A
2.1 (4-12 MHz)
6.25
1.5
N/A
2.1 (4-30 MHz)
1.00
3.7
12
N/A
AN/USC-38(V)
48.5
10.00
93.0
305
N/A
AN/USC-38(V)9 FOT
46.6
10.00
0.0
N/A
Classified
10.00
23.1
76
N/A
36.5
10.00
0.0
N/A
2.1
1.00
0.9
N/A
6.0
1.00
1.5
N/A
AN/VRC-90A
0.0
1.00
0.9
N/A
AN/VRC-93(V)
0.0
1.00
0.9
N/A
AN/URT-23 (Series)
AN/USG-2 (CEC)
AN/USQ-123(V) CHBDL
AN/VRC-46
AN/VRC-94
2.1
1.00
0.9
N/A
AN/WRC-1B
2.1
1.00
1.2
N/A
12.0
1.00
1.2
N/A
2.1
1.00
0.0
N/A
AN/WSC-3(V)3
AN/WSC-3(V)6
AN/WSC-3(V)7
AN/WSC-3(V)10
5.0
1.00
0.0
N/A
12.0
1.00
1.2
N/A
1.7
1.00
0.0
N/A
2.1
1.00
0.0
N/A
5.0
1.00
0.0
N/A
12.0
1.00
1.2
N/A
2.1
1.00
0.0
N/A
2-11

TRANSMITTER NAME
AN/WSC-3(V)11
AN/WSC-3(V)14
AN/WSC-3(V)15
ANTENNA GAIN
(dBi)
PEL
(mW/cm2)
HERP SAFE
STANDOFF DISTANCE
(Meters)
(Feet)
ROTATING
BEAM
HAZARD
N/A
1.7
1.00
0.0
2.1
1.00
0.0
N/A
2.1
1.00
0.0
N/A
2.1
1.00
0.0
N/A
12.0
1.00
1.2
N/A
AN/WSC-3(V)17
12.0
1.00
1.2
N/A
AN/WSC-3A(V)3
12.0
1.00
1.2
N/A
AN/WSC-3A(V)15
12.0
1.00
1.2
N/A
AN/WSC-6(V)4 & (V)5

7-ft dish @ 350 Watts
7-ft dish @ 2000 Watts
44.9
10.00
62.9
203
N/A
44.9
10.00
191.1
627
N/A
AN/WSC-6(V)7
42.5
10.00
100.6
330
N/A
AN/WSC-6(V)9
X-BAND
C-BAND
41.2
10.00
64.0
210
38.7
10.00
39.6
130
N/A
AN/WSC-8(V)1 & (V)2
42.8
10.00
72.2
237
N/A
6.1
1.00
0.9
N/A
2.1
1.00
0.6
N/A
5.0
1.00
0.9
N/A
GM 300
0.9
1.50
0.3
N/A
GX 2330S STD
8.0
1.00
1.2
N/A
HORIZON OMNI
2.1
1.00
0.6
N/A
HORIZON TITAN
2.1
1.00
0.6
N/A
IC 751A
2.1
18.40
0.3
N/A
ICM 56
8.0
1.00
1.2
N/A
2.1
1.00
0.6
N/A
6.0
1.00
0.9
N/A
2.1
1.00
0.6
N/A
6.0
1.00
0.9
N/A
ICM 80
2.1
1.00
0.6
N/A
ICM 100
2.1
1.00
0.6
N/A
ICM 125
2.1
1.00
0.6
N/A
ICM 125A
2.1
1.00
0.6
N/A
ICM 125D
2.1
1.00
0.6
N/A
ICM 126
2.1
1.00
0.6
N/A
ICM 127
2.1
1.00
0.6
N/A
23.9
23.9
5.45
5.45
2.7
2.7
9
9
N/A
N/A
2.1
1.00
0.6
N/A
FM 2610
FM 8500
ICM 57
ICM 58
INMARSAT
MX-2400
SATURN 3S.90
JHS-32A
2-12
N/A

TRANSMITTER NAME
ANTENNA GAIN
(dBi)
PEL
(mW/cm2)
HERP SAFE
STANDOFF DISTANCE
(Meters)
(Feet)
ROTATING
BEAM
HAZARD
N/A
LST-5C
1.0
1.00
0.3
M-200 MOTOROLA
2.1
1.00
0.6
N/A
11.4
5.45
0.0
N/A
MOTOROLA TRITON
8.1
1.00
1.2
N/A
MX-8102
2.1
1.00
0.6
N/A
NRE 332
2.1
1.00
0.6
N/A
OBT
6.0
1.00
0.9
N/A
RAY JEFFERSON
2.1
1.00
0.6
N/A
RAYNAV 55
2.1
1.00
0.6
N/A
RAYTHEON 53A
2.1
1.00
0.6
N/A
RAYTHEON 77
2.1
1.00
0.6
N/A
RAYTHEON 90 (VHF FM)
2.1
1.00
0.6
N/A
6.0
1.00
0.9
N/A
2.1
1.00
0.6
N/A
RAYTHEON 202
2.1
1.00
0.6
N/A
RAYTHEON 780 (VHF FM)
2.1
1.00
0.6
N/A
RT-1319/URC
2.1
1.00
0.6
N/A
STANDARD GX2341B
2.1
1.00
0.6
N/A
2.1
1.00
0.6
N/A
8.1
1.00
1.2
N/A
STD HORIZON NOVA
6.0
1.00
0.9
N/A
STD HORIZON OMNI
6.0
1.00
0.9
N/A
STD HORIZON TITAN
2.1
1.00
0.6
N/A
2.1 (2-6 MHz)
25.00
0.9
N/A
2.1 (2-30 MHz)
1.00
3.7
12
N/A
2.1 (4-12 MHz)
6.25
1.5
N/A
2.1 (10-30 MHz)
1.00
3.7
12
N/A
TKM 507
2.1
1.00
0.6
N/A
TRITON II
6.1
1.00
0.9
N/A
TS 850S KENWOOD
2.1
1.00
1.2
N/A
MINI-INMARSAT
NERA
RAYTHEON 201
STD HORIZON
T-1322 (Series)
2-13

Table 2-2. Shore-Based Communication and Satellite Systems
TRANSMITTER NAME
ANTENNA GAIN
(dBi)
PEL
(mW/cm2)
HERP SAFE
STANDOFF DISTANCE
(Meters)
(Feet)
ROTATING
BEAM
HAZARD
AN/FRC-30
3.0
1.10
7.6
25
N/A
AN/FRC-36
3.0
1.00
0.9
N/A
AN/FRC-52
2.1
1.00
0.9
N/A
AN/FRC-52A
2.1
1.00
0.9
N/A
AN/FRC-59
2.1
1.00
0.8
N/A
AN/FRC-59A
2.1
1.00
0.8
N/A
AN/FRC-70
2.1
1.00
1.2
N/A
AN/FRC-70A
2.1
1.00
1.2
N/A
AN/FRC-83
3.0
1.00
1.2
N/A
AN/FRC-84
37.5
10.00
1.5
N/A
AN/FRC-93 (Series)
10.0
1.00
6.4
21
N/A
AN/FRC-109 (Series)
37.5
10.00
2.1
N/A
AN/FRC-143
3.0
1.00
1.5
N/A
AN/FRC-144
2.1
1.00
1.2
N/A
AN/FRC-149
40.3
10.00
2.5
N/A
AN/FRC-150
3.0
1.00
0.9
N/A
AN/FRC-153 (Series)
3.0
1.00
4.3
14
N/A
AN/FRC-162(V)8
(w/P1271 Antenna)
47.1
10.00
6.4
21
N/A
AN/FRC-162(V)8
(w/P4710D Antenna)
37.5
10.00
2.1
N/A
2.2
1.00
0.9
N/A
AN/FRC-171 (Series)
40.3
10.00
4.3
14
N/A
AN/FRC-173 (Series)
40.3
10.00
4.3
14
N/A
AN/FRN-12A
2.1
1.00
1.8
N/A
AN/FRN-24
2.1
1.00
1.2
N/A
AN/FRN-29
4.5
1.00
1.2
N/A
AN/FRN-36
2.0
1.00
1.2
N/A
AN/FRN-39
1.5
1.00
0.3
N/A
AN/FRN-44
6.0
1.00
2.0
N/A
AN/FRT-24
3.0
1.00
4.3
14
N/A
AN/FRT-39 (Series)
3.0
1.10
12.1
40
N/A
AN/FRT-40 (Series)
3.0
1.10
24.0
79
N/A
AN/FRT-83 (Series)
8.0
1.10
9.8
32
N/A
AN/FRT-84(V)
4.0
1.00
6.4
21
N/A
AN/FRT-96
5.0
1.10
15.2
50
N/A
AN/FRC-166
2-14

TRANSMITTER NAME
ANTENNA GAIN
(dBi)
PEL
(mW/cm2)
HERP SAFE
STANDOFF DISTANCE
(Meters)
(Feet)
ROTATING
BEAM
HAZARD
AN/FSC-78
63.6
10.00
2595.9
8517
N/A
AN/FSC-79
60.0
10.00
2309.0
7574
N/A
AN/GRC-27
1.5
1.00
1.2
N/A
AN/GRC-27A
1.5
1.00
1.2
N/A
AN/GRC-112
6.0
1.00
7.0
23
N/A
AN/GRC-125
2.1
1.00
0.9
N/A
AN/GRC-134
1.5
1.00
1.2
N/A
AN/GRC-135
1.5
1.00
1.2
N/A
AN/GRC-135A
1.5
1.00
1.2
N/A
AN/GRC-160
2.1
1.00
0.9
N/A
AN/GRC-164
0.0
1.00
0.3
N/A
AN/GRC-168
3.0
1.00
0.6
N/A
AN/GRC-171
1.5
1.00
0.6
N/A
AN/GRC-175
4.0
1.00
0.9
N/A
AN/GRC-177
3.0
1.00
0.9
N/A
AN/GRC-193
2.2
1.10
2.4
N/A
AN/GRC-201
38.0
10.00
31.7
104
N/A
AN/GRC-212
12.0
1.00
35.7
117
N/A
AN/GRN-20
6.0
3.20
1.5
N/A
AN/GRN-25
22.0
1.00
2.7
N/A
AN/GRN-30(V)
28.0
1.00
11.3
37
N/A
AN/GRN-31(V)
16.0
1.10
1.5
N/A
AN/GRT-3
5.5
1.00
1.8
N/A
AN/GRT-20
5.5
1.00
1.2
N/A
AN/GRT-22
1.5
1.00
0.9
N/A
56.0
10.00
1082.7
3552
N/A
2.1
1.00
0.3
N/A
38.0
7.00
78.0
256
N/A
2.1
1.00
0.9
N/A
400.0
1.00
3.4
11
N/A
AN/MRC-108 (UHF)
28.0
1.00
0.6
N/A
AN/MRC-108 (VHF)
65.0
1.00
0.9
N/A
AN/MRC-109
2.1
1.00
0.9
N/A
AN/MRC-110
2.1
1.00
0.9
N/A
AN/MRC-135
9.6
1.00
2.4
N/A
AN/MRC-138
5.0
1.00
3.4
11
N/A
AN/GSC-39(V)1, 2
AN/GSQ-159
AN/MPS-38
AN/MRC-97A
AN/MRC-108 (HF)
2-15

TRANSMITTER NAME
ANTENNA GAIN
(dBi)
PEL
(mW/cm2)
HERP SAFE
STANDOFF DISTANCE
(Meters)
(Feet)
ROTATING
BEAM
HAZARD
AN/MRN-18
2.0
3.20
0.9
N/A
AN/MSC-43
5.0
1.10
4.6
15
N/A
AN/MSC-46
58.0
10.00
501.1
1644
N/A
AN/PRC-25
2.0
1.00
0.3
N/A
AN/PRC-27
2.1
1.00
0.3
N/A
AN/PRC-41
(w/AS-1404 Antenna)
2.1
1.00
0.3
N/A
AN/PRC-41
(w/AS-1405 Antenna)
12.0
1.00
0.6
N/A
AN/PRC-75
0.0
1.00
0.3
N/A
AN/PRC-77
10.0
1.00
0.6
N/A
AN/PRC-77A
10.0
1.00
0.6
N/A
AN/PRC-104 (w/AS-2259 or
AS-271A Antenna)
2.2
1.10
0.2
N/A
AN/PRC-104
(w/AT-1011 Antenna)
5.0
1.10
0.2
N/A
AN/PRC-118
6.0
1.00
1.5
N/A
AN/TLQ-17A
7.5
1.00
5.2
17
N/A
AN/TMQ-31
-0.3
1.00
0.6
N/A
AN/TRC-75
(w/AT-1011 Antenna)
5.0
1.10
4.6
15
N/A
AN/TRC-75
(w/GRA-50 Antenna)
2.2
1.10
3.4
11
N/A
AN/TRC-97
(w/AS-1731 Antenna)
38.0
10.00
71.0
233
N/A
AN/TRC-97
(w/AS-1939 Antenna)
20.0
10.00
9.1
30
N/A
AN/TRC-97A (10 Watts)
38.0
10.00
7.3
24
N/A
AN/TRC-97A (1000 Watts)
38.0
10.00
71.0
233
N/A
2.0
1.00
0.3
N/A
AN/TRC-170(V)1
44.5
10.00
426.1
1398
N/A
AN/TRC-170(V)2, 5
Line of Sight
40.5
10.00
2.1
N/A
AN/TRC-170(V)2, 5
Troposcatter
40.5
10.00
133.8
439
N/A
AN/TRC-170(V)3
Line of Sight
36.5
10.00
1.5
N/A
AN/TRC-170(V)3
Troposcatter
36.5
10.00
84.4
277
N/A
AN/TRC-166
2-16

TRANSMITTER NAME
ANTENNA GAIN
(dBi)
PEL
(mW/cm2)
HERP SAFE
STANDOFF DISTANCE
(Meters)
(Feet)
ROTATING
BEAM
HAZARD
AN/TRC-176 (Series)
1.5
1.00
0.6
N/A
AN/TRN-33
1.5
1.00
0.9
N/A
AN/TSC-15
5.0
1.10
4.6
15
N/A
AN/TSC-54
52.0
10.00
794.1
2605
N/A
AN/TSC-85
43.5
10.00
298.4
979
N/A
AN/TSC-85(V)
43.5
10.00
298.4
979
N/A
7.5
1.10
6.4
21
N/A
AN/TSC-96(V)
10.0
1.00
1.8
N/A
AN/TXQ-3
(w/TXR-4 System)
33.5
10.00
0.6
N/A
AN/TXQ-3
(w/TXT-3 System)
33.5
10.00
4.5
14
N/A
AN/VRC-17
2.1
1.00
0.6
N/A
AN/VRC-33
2.1
1.00
0.9
N/A
AN/VRC-42
2.1
1.00
0.6
N/A
AN/VRC-43
2.1
1.00
0.9
N/A
AN/VRC-46
3.0
1.00
1.2
N/A
AN/VRC-47
2.1
1.00
0.9
N/A
AN/VRC-49
2.1
1.00
0.9
N/A
AN/VRC-51
3.0
1.00
0.9
N/A
AN/VRC-52
2.1
1.00
0.6
N/A
AN/VRC-56
2.1
1.00
0.6
N/A
AN/VRC-60
2.1
1.00
0.9
N/A
AN/VRC-64
3.0
1.00
0.9
N/A
AN/VRC-68
2.1
1.00
0.6
N/A
AN/VRC-77
2.1
1.00
0.9
N/A
AN/VRC-78
2.1
1.00
0.6
N/A
AN/VRC-82(V)1
2.1
1.00
0.9
N/A
12.5
1.00
5.5
18
N/A
AN/TSC-95
LST-5D
2-17

Table 2-3. Shipboard Radar and Navigation Systems
TRANSMITTER NAME
ANTENNA NAME
PEL
(mW/cm2)
HERP FIXED-BEAM
STANDOFF DISTANCE
(Meters)
(Feet)
ROTATING
BEAM
HAZARD
None
1352 FURUNO
1352
10.00
0.6
1510D FURUNO
XN4A
10.00
1.5
None
1731 FURUNO
1731
10.00
0.6
None
1751 FURUNO
1751
10.00
2.4
None
1830 FURUNO
1830
10.00
0.6
None
1831 FURUNO
1831
10.00
0.6
None
RSB-022
10.00
0.6
None
1930
10.00
0.6
None
1931 FURUNO
1931
10.00
0.6
None
1940 FURUNO
1940
10.00
0.6
None
2010 FURUNO
2010
10.00
7.3
24
None
2115B FURUNO
FURUNO
10.00
1.5
None
2120 FURUNO
2120
10.00
6.4
21
None
803
803
10.00
0.9
None
AS-177B/UPX
3.60
0.3
None
AS-3020/SR
3.60
0.3
None
1930 FURUNO
AN/APX-72A
3.60
0.3
None
AN/BPS-14
AS-3021/SR
AS-1640/BPS
10.00
11.2
37
None
AN/BPS-15
AS-1640B/BPS
10.00
3.0
10
None
AN/BPS-15A
AS-1640B/BPS
10.00
3.0
10
None
AN/BPS-15B
AS-1640B/BPS
10.00
3.0
10
None
AN/BPS-15C
AT-294/BPS-15
10.00
3.0
10
None
AN/BPS-15D
AS-996/BPS-9A
10.00
3.0
10
None
AN/BPS-15E
AS-1640B/BPS
10.00
3.0
10
None
AN/BPS-15F
AS-1640B/BPS
10.00
3.0
10
None
AN/BPS-16(V)1
AS-4316/BPS-16(V)
10.00
3.9
13
None
AN/BPS-16(V)2
AS-4316/BPS-16(V)
10.00
3.9
13
None
AN/SLQ-32(V)3
CW-1186
10.00
29.3
96
None
AN/SPG-60
CWI
TRACK
MK 39
10.00
10.00
280.4
112.8
920
370
None
None
AN/SPG-62
AS-3444/SPG-62
10.00
353.6
1160
None
AS-1292/TPN-8
10.00
14.3
47
None
AS-1669/SPN-35
10.00
11.0
36
None
AN/SPN-41
AS-2580/UPN
10.00
None
AN/SPN-43
AS-2785A/SPN-43A
10.00
18.3
60
None
AN/SPN-46(V)
AS-3648/SPN-46(V)
10.00
3.1
10
None
AN/SPQ-9A
AS-2367A/SPQ-9
10.00
5.5
18
None
AN/SPQ-9B
AS-4499/SPQ
10.00
44.8
147
None
AN/SPN-35
2-18

TRANSMITTER NAME
ANTENNA NAME
PEL
(mW/cm2)
HERP FIXED-BEAM
STANDOFF DISTANCE
(Meters)
(Feet)
ROTATING
BEAM
HAZARD
None
AN/SPS-10B
AS-936B/SPS
10.00
13.1
43
AN/SPS-10F
AS-936B/SPS-10B
10.00
13.1
43
None
AN/SPS-40
AS-2782/SPS-40B
1.30
58.2
191
None
AN/SPS-48C
Normal
Burnthru
AS-1686/SPS-48
10.00
10.00
319.4
356.0
1048
1168
None
None
AN/SPS-48E
AS-3752/SPS-48E
10.00
458.7
1505
None
AN/SPS-49(V)
AS-3263/SPS-49(V)
2.80
130.5
428
None
AN/SPS-55
AS-2953/SPS-55
10.00
5.5
18
None
AN/SPS-64(V)
AS-3194/SPS-64
10.00
< 1.2
<4
None
AS-936A/SPS-10B
10.00
5.8
18
None
AS-936B/SPS-10B
10.00
15.8
52
None
AN/SPS-73(V)
AS-4437/SPS-73(V)
10.00
0.9
None
AN/SPY-1A/B/D
Low Power
High Power
Burnthru
various
10.00
10.00
10.00
15.2
109.7
164.6
50
360
540
None
None
None
AS-177B/UPX
3.40
0.3
None
AS-2188/U
3.40
0.9
None
AS-3134/UPX
3.40
1.2
None
AS-177B/UPX
3.40
0.3
None
AS-2188/U
3.40
0.9
None
AS-2189/U
3.40
0.9
None
AS-177B/UPX
3.40
0.3
None
AS-2188/UPX
3.40
0.9
None
AS-2189/U
3.40
0.9
None
AS-177B/UPX
3.40
0.3
None
AS-1065/UPX
3.40
1.5
None
AS-2188A/U
3.40
0.9
None
AS-2188/U
3.40
0.9
None
AS-2189/UPX
3.40
0.9
None
AS-3134/UPX
3.40
1.2
None
AS-177B/UPX
3.60
0.3
None
AN/SPS-67(V)
AN/UPX-23
AN/UPX-25
AN/UPX-25(V)
AN/UPX-27
AN/UPX-28
AS-3134/UPX
3.60
0.3
None
AN/URN-25(V)
AS-3240/URN
3.20
1.2
None
FCR 2825 FURUNO
2825
10.00
3.4
11
None
FCR 904 FURUNO
AM 2436
10.00
0.6
None
FCR 1030 FURUNO
XN8
10.00
1.5
None
FCR 1040 FURUNO
XN12A
10.00
0.6
None
FCR 1100 FURUNO
FCR 1040A FURUNO
10.00
3.7
12
None
2-19

TRANSMITTER NAME
ANTENNA NAME
PEL
(mW/cm2)
HERP FIXED-BEAM
STANDOFF DISTANCE
(Meters)
(Feet)
ROTATING
BEAM
HAZARD
None
XN4A
10.00
3.7
12
FRC-1411
10.00
3.4
11
None
FR 1510 FURUNO
1510
10.00
0.6
None
FR 1510D FURUNO
XN3
10.00
0.6
None
FR 1942 FURUNO
RSB-0062
10.00
1.5
None
FR 2020 FURUNO
XN2
10.00
3.7
12
None
FR 2110 FURUNO
FURUNO
10.00
3.7
12
None
FR 8100D FURUNO
8100D
10.00
3.4
11
None
FR 8250D FURUNO
XN3
10.00
1.5
None
LN 66
201-760002 401
10.00
< 1.2
<4
None
M821
RSB-0067
10.00
0.3
None
MARK 15 MOD
(CIWS)
SEARCH**
10.00
10.7
83
None
TRACK
10.00
36.6
116
None
4.20
4.20
22.9
36.9
75
121
None
None
MK 53 MOD 2 SEARCH
10.00
61.6
202
None
MK 53 MOD 2 TRACK
10.00
43.6
143
None
MARK 95 MOD
(NSSMS)
MK 95 MOD
10.00
89.3
293
None
PATHFINDER
MODEL 1402
10.00
2.7
None
R 21X RAYTHEON
MB 9955
10.00
3.7
12
None
R 40X RAYTHEON
R40X
10.00
0.6
None
RAY 1206 RAYTHEON
RAY 1206
10.00
3.4
11
None
RDP 104 FURUNO
XN2
10.00
0.6
None
RF 7062 FURUNO
RF 7062
10.00
1.5
None
FCR 1411 FURUNO
MARK 23 MOD 3
TAS
Low Power
High Power
MARK 69 MOD 1
2-20
MK 48 MOD 1

Table 2-4. Shore-Based Radar and Navigation Systems
TRANSMITTER NAME
AN/FPN-28
AN/FPN-36
AN/FPN-50
AN/FPN-63(V)
ANTENNA NAME
AS-762/AS-763
PEL
(mW/cm2)
HERP FIXED-BEAM
STANDOFF DISTANCE
(Meters)
(Feet)
ROTATING
BEAM
HAZARD
None
10.00
55.2
181
9.30
32.6
107
None
AS-866/FPN-33
10.00
21.3
70
None
AS-867/FPN-33
10.00
26.8
88
None
AS-519/GPN (Azimuth)
10.00
16.8
55
None
9.30
31.7
104
None
AS-1208/MPN (Elevation)
10.00
20.7
68
None
AS-3161/UPN (Azimuth)
10.00
21.9
72
None
AT-291/GPN (Elevation)
10.00
24.7
81
None
4.30
47.5
156
None
AS-964/GPN
AS-964/GPN
AN/FPS-8
AT-386/FPS-8
AN/FPS-16
AS-903/FPS-16
10.00
147.2
483
None
AN/FPS-16 Mod
ZZ/FPS-16 Mod
10.00
211.8
695
None
AN/FPS-16(V)
AS-903/FPS-16
10.00
73.8
242
None
AN/FPS-20Q
AT-572/FPS-20
4.20
161.0
528
None
AN/FPS-36
AS-847/FPS
4.20
43.9
144
None
AN/FPS-41
AS-2390/FPS-41
9.00
39.0
128
None
AN/FPS-68
OA-3413/FPS-68
10.00
24.1
79
None
AN/FPS-81
OA-3870/FPS-81
10.00
24.1
79
None
AN/FPS-81A
OA-3870/FPS-81
10.00
24.1
79
None
AN/FPS-105
ZZ/FPS-105
10.00
2.1
None
AN/FPS-106(V)1
OA-3870/FPS-81
10.00
24.1
79
None
AN/FPS-106(V)2
AS-2878/FPS-106
10.00
34.1
112
None
AN/FPS-114
AS-4005/FPS-114
9.60
38.7
127
None
AN/FPS-127
IAIA
8.70
2.7
None
AN/FPS-131
ZZ/TPS-76
10.00
72.8
239
None
AN/GPN-27
FA 9344
9.00
45.4
149
None
AN/GRN-9
OA-1547/URN
3.20
1.2
None
AN/GRN-9B
OA-1547/URN
3.20
1.2
None
AN/GRN-9C
OA-1547/URN
3.20
1.2
None
AS-762/AS-763
10.00
57.0
187
None
9.30
32.6
107
None
OA-642/MPN-11
(Elevation)
10.00
20.7
68
None
OA-643/MPN-11 (Azimuth)
10.00
16.8
55
None
9.30
36.9
121
None
OE-250-V/UPN (Elevation)
10.00
23.5
77
None
OE-251-V/UPN (Azimuth)
10.00
22.0
72
None
AN/MPQ-46
ZZ/1193 RX
10.00
84.4
277
None
AN/MPS-25(V)
OA-1613/FPS-16
10.00
92.7
304
None
AN/MPN-5
AN/MPN-14
AS-964/GPN
ZZ/MPN-11 (Search)
AN/MPN-23(V)
2-21

Table 2-4. Shore-Based Radar and Navigation Systems
TRANSMITTER NAME
ANTENNA NAME
PEL
(mW/cm2)
HERP FIXED-BEAM
STANDOFF DISTANCE
(Meters)
(Feet)
ROTATING
BEAM
HAZARD
None
AN/MRN-16
AS-686/URN-3
3.20
0.9
AN/MRN-18, 18A
AS-686/URN-3
3.20
0.9
None
AN/MRN-21
AS-686/URN-3
3.20
0.9
None
AN/MSQ-51
(Acquisition)
ZZ/MSQ-51
10.00
60.0
197
None
AN/MSQ-51 (Track)
OA-4453/MSQ-51
10.00
23.8
78
None
AN/TPN-8
AS-1292/TPN-8
10.00
26.2
86
None
AN/TPN-8A
AS-2284/TPN-8A
10.00
27.7
91
None
AN/TPN-22
AS-3471/TPN-22
10.00
33.8
111
None
AS-2579/UPN
10.00
2.4
None
AS-2580/UPN
10.00
4.6
15
None
AN/TPQ-10
AT-918/TPQ-10
10.00
27.1
89
None
AN/TPQ-27
AS-3279/TPQ-27
10.00
130.4
428
None
AN/TPQ-36
OE-338/TPQ-36(V)
10.00
74.4
244
None
AN/TPS-22
OA-3447/TPS-22
1.30
169.1
555
None
AN/TPS-32
AS-2536/TPS-32
9.70
900.7
2955
None
AN/TPS-34
AS-1277/TPS-34
4.20
331.9
1089
None
AN/TPS-35
OA-4905/TPS-35
4.20
32.6
107
None
AN/TPS-40
OA-1196/MPS-16
10.00
120.3
395
None
AN/TPS-43
OE-48/TPS-43
9.70
190.5
625
None
AN/TPS-59
GE-7327402G1
4.00
223.7
734
None
AN/TPS-63
AS-4021/T
4.00
59.7
196
None
AN/GPA-123
3.40
2.1
None
ZZ/TPX-49A
3.40
0.3
None
AN/TPX-42A(V)
AN/GPA-123
3.40
0.9
None
AN/TPX-42A(V)3, 5
AN/GPA-123
3.40
0.9
None
AN/TPX-42A(V)8
OE-XXX/UPX
3.40
0.9
None
AS-2579/UPN
10.00
3.4
11
None
AS-2580/UPN
10.00
6.4
21
None
AN/TPN-30
AN/TPX-42(V)3, 5
AN/TRN-28
AN/UPS-1A thru -1F
ZZ/UPS-1 TYPE 2
4.20
38.7
127
None
AN/URN-3
OA-553/URN
3.20
1.5
None
AN/URN-3A
AS-685/URN-3
3.20
0.9
None
2-22

Table 2-5. Aircraft Radar Systems
AIRCRAFT
PLATFORM
RADAR SYSTEM
HERP FIXED-BEAM
PEL
(mW/cm2)
STANDOFF
(Meters)
DISTANCE
(Feet)
ROTATING
BEAM
HAZARD
N/A
A/V-8B HARRIER
AN/APG-65
10.0
40.8
134.0
C-2 GREYHOUND
PRIMUS 870
10.0
1.2
4.0
N/A
C-9B SKYTRAIN
BENDIX/KING RDR1E
10.0
12.8
42.0
N/A
C-20 GULFSTREAM IV
PRIMUS 870
10.0
1.2
4.0
N/A
C-37 GULFSTREAM V
PRIMUS 880
10.0
3.1
10.0
N/A
C-40A CLIPPER
RAYTHEON WXR2100
10.0
14.8
49.0
N/A
C-130 HERCULES
AN/APS-133(V)3
10.0
10.2
34.0
N/A
KC-130 HERCULES
AN/APN-241
10.0
3.9
13.0
N/A
E-2C HAWKEYE
AN/APS-145
1.4
57.6
189.0
None
E-6A MERCURY
AN/APS-133(V)
10.0
10.2
34.0
N/A
F-14 (ALL MODELS)
AN/AWG-9 OR
AN/APG-71
10.0
SEE PAGE 2-36
N/A
N/A
F/A-18 (ALL MODELS)
AN/APG-65 OR
AN/APG-73
10.0
40.8
134.0
N/A
P-3C ORION
AN/APG-66
10.0
12.7
42.0
N/A
P-3C ORION
AN/APS-115B
10.0
18.8
62.0
N/A
P-3C ORION
AN/APS-137B(V)5
10.0
33.7
111.0
N/A
S-3B VIKING
AN/APS-137A(V)1
10.0
33.5
110.0
None
SH-60B SEAHAWK
AN/APS-124
10.0
17.4
57.0
None
T-39N SABERLINER
AN/APG-66N
10.0
12.7
42.0
N/A
UC-12B HURON
COLLINS WXR-270
10.0
3.3
11.0
N/A
UC-35 CITATION
PRIMUS 650
10.0
1.2
4.0
N/A
V-22 OSPREY
AN/APQ-174B
10.0
7.1
23.0
N/A
During
ground radar operation, personnel shall remain outside the area defined by the HERP safe separation distances and antenna scan angles depicted in figure 2-2.
See
paragraph D-6 for a discussion of rotating beam hazards.
2-23

Table 2-6. Aircraft Radiation Patterns
AIRCRAFT
2-24
PAGE
A/V-8B HARRIER
2-25
C-2 GREYHOUND
2-26
C-9B SKYTRAIN
2-27
C-20 GULFSTREAM IV
2-28
C-37 GULFSTREAM V
2-29
C-40A CLIPPER (BOEING 737-700)
2-30
C-130 HERCULES
2-31
KC-130 HERCULES
2-32
E-2C HAWKEYE
2-33
E-6A MERCURY (TACAMO)
2-34
EA-6B PROWLER
2-35
F-14 (ALL MODELS)
2-36
F/A-18 (ALL MODELS)
2-37
P-3C ORION
2-38
P-3C ORION
2-39
P-3C ORION
2-40
S-3B VIKING
2-41
SH-60B SEAHAWK
2-42
T-39N SABERLINER
2-43
UC-12B HURON
2-44
UC-35 CITATION
2-45
V-22 OSPREY
2-46

Aircraft
A/V-8B HARRIER
Radars
AN/APG-65
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
40.8 METERS/134.0 FEET
70
FIGURE 2-2. Aircraft Radiation Patterns
2-25

Aircraft
C-2 GRAYHOUND
Radars
HONEYWELL PRIMUS 870
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
1.2 METERS/4.0 FEET
60
FIGURE 2-2. Aircraft Radiation Patterns (Continued)
2-26

Aircraft
C-9B SKYTRAIN
Radars
BENDIX/KING RDR-1E
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
90
2-27

Aircraft
C-20 GULFSTREAM IV
Radars
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
1.2 METERS/4.0 FEET
60
2-28

Aircraft
C-37 GULFSTREAM V
Radars
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
60
2-29

Aircraft
C-40A CLIPPER (BOEING 737-700)
Radars
RAYTHEON WXR-2100
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
70
2-30

Aircraft
C-130 HERCULES
Radars
AN/APS-133(V)3
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
90
2-31

Aircraft
KC-130 HERCULES
Radars
AN/APN-241
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
135
2-32

Aircraft
E-2C HAWKEYE
Radars
AN/APS-145
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
360
2-33

Aircraft
E-6A MERCURY (TACAMO)
Radars
AN/APS-133(V)
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
90
2-34

Aircraft
EA-6B PROWLER
Radars
AN/APS-130B(V)1
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
57
2-35

Aircraft
F-14 (ALL MODELS)
Radars
AN/AWG-9 OR AN/APG-71
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
AS SHOWN
2-36

Aircraft
F/A-18 (ALL MODELS)
Radars
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
AN/APG-65 OR AN/APG-73
70
2-37

Aircraft
P-3C ORION
Radars
AN/APG-66
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
90 (NOSE AND TAIL)
2-38

Aircraft
P-3C ORION
Radars
AN/APS-115B
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
90 (NOSE AND TAIL)
2-39

Aircraft
P-3C ORION
Radars
AN/APS-137B(V)5
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
90 (NOSE AND TAIL)
2-40

Aircraft
S-3B VIKING
Radars
AN/APS-137A(V)1
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
360
2-41

Aircraft
SH-60B SEAHAWK
Radars
AN/APS-124
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
360
2-42

Aircraft
T-39N SABERLINER
Radars
AN/APG-66N
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
60
2-43

Aircraft
UC-12B HURON
Radars
COLLINS WXR-270
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
60
2-44

Aircraft
UC-35 CITATION
Radars
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
1.2 METERS/4.0 FEET
60
2-45

Aircraft
V-22 OSPREY
Radars
AN/APQ-174B
HERP SAFE
Separation Distance
ANTENNA SCAN ANGLE
70
2-46

CHAPTER 3
RF BURNS
3-1.
SCOPE
This chapter discusses radio-frequency (RF) burns, why they can occur, and the
procedures for minimizing RF burn hazards. An RF burn hazard will exist if there is a
sufficiently high induced RF voltage on a metallic object to cause pain, visible skin damage, or
involuntary reaction to a person who comes in contact with the object. The RF burn
phenomenon is distinct from hazards of electromagnetic radiation to personnel and electrical
shock.
3-2.
RF BURNS FROM CARGO-HANDLING EQUIPMENT
3-2.1 GENERAL. The use of high-frequency (HF) transmitters (1 kW and up), and the
complicated structure and rigging aboard ship, especially cargo ships, has increased the
probability of voltages being induced on various objects. The handling of metallic cargo lines
while shipboard HF transmitters are radiating can be hazardous to ships personnel. On
numerous occasions, RF voltages have been encountered on items such as crane hooks,
running rigging, booms, missile launchers, and parked aircraft. These voltages, which may be
sufficient to cause injury, are induced on the metallic items by radiation from nearby transmitting
antennas.
3-2.2 RF BURN EFFECTS. An RF burn is the result of RF current flow through that portion of
the body in direct contact with a conductive object (in which an RF voltage has been induced) or
at the site of a spark discharge (no direct contact with a conductive object). Any burn injury that
occurs is entirely the result of heat produced by current flow through the resistance of the skin.
Current flow through a resistance produces heat regardless of the nature of the circuit. The
effect of the heat on a person ranges from warmth to painful burns. The specific level at which
contact with RF voltage should be classified as an RF burn hazard is not distinct. Hazardous,
for the purpose of this section, is defined as the RF voltage that will cause a person pain or
visible skin damage, or will cause an involuntary reaction. The term "hazard" does not include
the lower voltages that cause annoyance, a stinging sensation, or moderate heating of the skin.
Naval Sea Systems Command (NAVSEA), Code 53H, has established that an open-circuit RF
voltage exceeding 140 volts on an item in an RF radiation field is to be considered hazardous.
However, field tests have shown that, because of the many variables involved, it is not
uncommon to encounter significantly higher voltages that do not result in a burn problem.
3-2.3
ELECTRICAL CHARACTERISTICS OF METALLIC OBJECTS.
3-2.3.1 All metallic items, regardless of intended use, have electrical properties of resistance,
inductance, and capacitance. These properties depend upon the material, the size and shape
of the objects, and the proximity of the objects to each other. The effect of the inductance and
capacitance is frequency dependent. A configuration of metallic objects can be represented by
3-1

an approximately equivalent electrical circuit such as that illustrated by figure 3-1, a typical
example of cargo-handling equipment. Potentially harmful voltages (current) may be generated
when radiated electromagnetic energy couples to such equipment. At radio frequencies, the
reactive components are the significant ones, and maximum voltage will be developed at a
frequency and location where the inductive (L) and capacitance (C) reactances are equal; i.e.,
where there is a resonant circuit. This behavior is characteristic of an antenna.
3-2.3.2 Metallic objects having the physical and electrical characteristics of an antenna are
commonplace aboard ships. Long lengths of metallic lines are particularly efficient interceptors
of RF energy. The amplitude of the induced RF voltage depends on:
a. The length of the line with respect to the wavelength of the exciting RF field.
b. The nearness of the line to a radiating antenna.
c. The power being radiated by the transmitting antenna.
d. The orientation of the line with respect to the transmitting antenna.
Since most shipboard antennas transmit vertically polarized fields, voltages are more likely to
be induced in vertical lines than in lines oriented in other directions.
3-2.3.3 As a practical matter, whether an induced voltage creates an RF burn hazard also
depends upon whether personnel will come into contact with the object. Generally, only the
voltage between an object and the deck is important.
3-2.3.4 Cargo ships, with their long lengths of metallic cables, are more likely to encounter the
RF burn problem than other types of ships, although the problem is not limited to that type.
Figure 3-1.
3-2
Electrical Equivalent of Cargo-Handling Equipment

3-2.3.5 When conditions conducive to RF burn hazards exist aboard ship, proper
measurements are necessary to determine the extent of the hazard. Valid data from
comprehensive tests will lead to recommendations to ensure maximum personnel safety with a
minimum of operational limitations.
3-3.
RF BURN HAZARD REDUCTION TECHNIQUES
3-3.1 INTRODUCTION. While there is no universally applicable method to completely

eliminate RF burn hazards, there are several approaches to eliminating the problem in some
cases or, in other cases, reducing it to manageable proportions. NAVSEA is continuing to
search for methods to eliminate the hazard.
3-3.2 LIMITING BODY CONTACT CURRENT. As discussed in Department of Defense
Instruction (DODINST) 6055.11, for frequencies between 100 kHz and 100 MHz, limiting body
contact current to a maximum of 100 mA will significantly reduce the likelihood of RF burns. For
frequencies between 3 kHz and 100 kHz, the contact current limit is frequency dependent.
3-3.3 HOOK INSULATORS. One method of eliminating the RF burn hazard on boom whip
and downhaul hooks is to install an insulator link between the rigging and the hook. Tests have
shown that these insulators are effective in the prevention of RF burns to the extent that contact
with the hook itself will not injure anyone, but the RF voltage and potential burn hazard above
the insulator remains unaffected. Unfortunately, numerous equipments involved in the RF burn
problem are not amenable to the use of an insulating link.
3-3.4 NONMETALLIC MATERIALS. Another approach being pursued is the use of
nonmetallic materials for applications where the RF burn hazard is a problem. Objects that can
be made of nonconducting material will not be susceptible to induced voltages. At the present,
though, there is no suitable nonmetallic substitute for the wire rope used on cargo equipment.
3-3.5 ANTENNA RELOCATION. Eliminating RF burn hazards by relocating antennas is often
tempting but seldom practical. Because so many factors are involved in designing a shipboard
antenna system, antenna relocation is not a feasible general solution to the RF burn hazard
problem. Nevertheless, antenna relocation should not be abandoned as an impossibility.
3-3.6 OPERATIONAL PROCEDURES. In some cases, the RF burn hazard can be eliminated
only through the use of restrictive operating procedures that govern the simultaneous use of
transmitters and cargo equipments. These procedures incorporate the use of techniques such
as operation of transmitters at reduced power and the prohibition of simultaneous use of certain
combinations of antennas, frequencies, and cargo-handling equipments. The use of
operational limitations will reduce the effectiveness of all equipments involved; therefore, these
limitations must not be excessively restrictive. Effective operational procedures can be
developed only after a shipboard RF burn survey has been conducted. Following this survey,
specific operational procedures must be developed by persons who have a thorough
knowledge of the operational requirements of the ship and have the authority to designate
which operations and equipments have priority over others.
3-3

3-3.7 RF RADIATION HAZARD WARNING SIGNS. In cases where RF burn hazards cannot
be eliminated, the probability of personnel coming in contact with hazardous voltages can be
reduced through the use of RF radiation hazard warning signs, as discussed in paragraph 22.2. The locations for posting the signs should be chosen with care to ensure that they will
pinpoint, as nearly as possible, the exact location of potential hazards. Indiscriminate and
excessive use of the signs will reduce their effectiveness.
3-4

CHAPTER 4
BIOLOGICAL RADIATION HAZARD FROM LASER DEVICES
4-1.
INTRODUCTION
4-1.1 The acronym "Laser" is derived from the initial letters of the words "Light Amplification by
Stimulated Emission of Radiation." The term "optical maser" was used earlier because the
original work was done with microwaves. Figure 4-1 illustrates the laser wavelength spectrum.
The biological effects of laser radiation are similar to light generated by high-intensity,
conventional ultraviolet (UV), infrared, and visible light sources such as the sun, nuclear
explosions, or arc lamps. However, the chance of eye or skin damage is greater from laser
radiation because the laser output is highly coherent (in phase), and the high intensity is
localized into a very directional beam. When laser radiation is absorbed by the body or eyes, it
is converted into heat which, in turn, causes redness, blistering, and, if intense enough, even
charring of the skin or visual impairment, which may be permanent.
4-1.2 Developments in laser technology have resulted in an increase in the use of these
devices for military applications, both for research and operational use. The widespread use of
these systems increases the probability of personnel exposure to injurious intensities of laser
radiation. Adequate safeguards are needed, since injury may occur at considerable distance.
All equipment containing lasers, and all lasers produced after 2 August 1976, must comply with
the Radiation Control for Health and Safety Act, Code of Federal Regulations (CFR) Title 21,
Subchapter J, Part 1040, unless it has an exemption from the National Center for Devices and
Radiological Health, Rockville, Maryland. The procedures for using lasers safely are contained
in American National Standards Institute (ANSI) Z136.1. The following provides some of the
essential safety requirements for use at Navy shore installations and aboard ships.
4-2.
GENERAL PRECAUTIONS APPLICABLE TO ALL LASER INSTALLATIONS
4-2.1 For a summary of hazards and sample laser safety emission control (EMCON) bills, refer
to Chief of Naval Operations Instruction (OPNAVINST) 5100.27/Marine Corps Order (MCO)
5104.1 (series), Navy Laser Hazards Control Program.
4-2.2 Unprotected personnel shall never be exposed to laser radiation in excess of the
maximum permissible exposure (MPE) levels specified in ANSI Z136.1.
4-2.3 Direct viewing of laser beams, even during optical alignment, is prohibited when levels
are greater than the MPE.
4-2.4 Optical viewing systems such as lenses, telescopes, etc., may increase the hazard to the
eye.
4-1

4-2
FIGURE 4-1. Laser Wavelength Chart

4-2.5 All involved personnel shall be trained to avoid looking directly at an operating laser or its
reflection. Personnel protective equipment (laser eye protection), specifically designed and
marked (with optical density and wavelength) for protection against radiation from the laser
system in use, shall be used when engineering or procedural controls are inadequate to
eliminate radiation levels in excess of the MPE.
4-2.6 Laser protective eyewear shall be marked with optical density values and wavelength for
which protection is afforded, and shall be issued to involved personnel. The eyewear shall
provide a snug fit. Periodic inspections of the goggles shall include:
a.
Inspection of the attenuator material for pitting, crazing, cracking, etc.
b.
Inspection of the goggle frame for mechanical integrity and leaks.
4-2.7 Only authorized personnel shall operate laser systems.

4-2.8 Spectators shall not be allowed access to the laser control area unless appropriate
supervisory approval has been obtained and protective measures taken.
4-2.9 At least two people should be present at all times when lasers are in operation so that
first aid may be rendered in the event of an injury and to prevent access by unauthorized
personnel. Where the operation allows, a countdown procedure should be followed to minimize
unnecessary exposure by donning laser eye protection and/or moving out of the path of the
laser beam.
4-2.10 Reflecting surfaces such as mirrors, bottles, windows, and metal, or other surfaces
which have a high coefficient for specular reflection, shall be eliminated from the beam path or
shall be faced and/or surrounded with diffuse substances to absorb the energy.
4-2.11 Lasers and laser beams should be contained within a suitably controlled equipment or
space so that noninvolved personnel in such an area cannot be accidentally injured. Laser
beams emitted by an unenclosed system must be terminated at the end of the beam path if the
exposure level is greater than the maximum allowable level. The backstop shall be of material
that will absorb the particular wavelength. Special care in absorbing and containing the laser
radiation must be taken, especially when the laser is emitting energy in the UV or infrared
portions of the spectrum, because an observer might receive damage to the eyes without being
aware of the reflection. Laser controls must be located to prevent operator exposure to unsafe
levels of radiation.
4-2.12 Hazardous byproducts may result from the reaction of the laser radiation (especially UV
laser radiation) with air and other substances (toxic/explosive gases, skin irritants, radiofrequency/UV/x-ray emissions, plasma).
4-2.13 The following are examples (sources) of hazards typically associated with laser
operations:
a.
High-voltage electrical hazards.
b.
Use of cryogenics.
4-3

c.
Compressed gases.
d.
Carcinogenic material.
e.
Noise.
f.
Arc lamps, filament lamps, capacitors (explosion hazards).
g.
Targets (which may shatter/explode).
h.
Ionizing radiation.
i.
Incoherent optical and UV radiation from laser discharge tubes or flash lamps.
Proper personnel protection and procedures shall be provided in the use of cryogenics.
Compressed gas bottles shall be secured. All laser discharge tubes or flash lamps, the laser
target, capacitors, and all elements of the optical train which may shatter shall be adequately
contained. All voltages in excess of 30 volts shall be guarded. All incidental radiation shall be
adequately shielded. The laser spaces shall be adequately ventilated to remove toxic gases.
All toxic materials shall be so marked and adequately controlled. Smoking, eating, or drinking
in laser beam areas should be prohibited.
4-3.
LASER CLASSIFICATION AND LABELING
4-3.1 All lasers, other than military exempt lasers, must be classified and labeled by the
manufacturers per CFR Title 21, Part 1040.10. Military exempt lasers are classified per ANSI
Z136.1. This classification system is based on laser output parameters. There are four laser
hazard classifications that determine the required extent of radiation safety controls. These
range from class I lasers that are safe for direct beam viewing under most conditions, to class
IV lasers that require the strictest controls. Laser product classification pertains to intended use
only. When a laser product is disassembled for maintenance and protective features are
removed, the laser classification may change to a more hazardous class. Details concerning
laser classification are in CFR Title 21, Part 1040.10, and ANSI Z136.1. Controls for each class
are addressed in OPNAVINST 5100.27/MCO 5104.1 (series) and its referenced instructions.
4-3.2 MILITARY EXEMPT LASERS. As per OPNAVINST 5100.27/MCO 5104.1 (series), the
Navy Laser Safety Review Board (LSRB) must approve most class III and class IV lasers, and
all military exempt lasers, prior to their use within the Department of the Navy. All lasers used
for combat, combat training, or classified in the interest of national security are eligible for this
exemption and, if so designated by the LSRB, are exempt from federal requirements applicable
to commercial products. Military exempt lasers must be labeled as shown in figure 4-2 (or as
specified by the LSRB) and, upon request, an inventory of a commands class III, class IV, and
military exempt lasers shall be sent to the Bureau of Medicine and Surgery (MED 212) per
OPNAVINST 5100.27/MCO 5104.1 (series).
4-4

CAUTION FOR MILITARY EXEMPT LASERS

This electronic product has been exempted from FDA radiation safety performance
standards prescribed in the Code of Federal Regulations, Title 21, Chapter I, Subchapter J, pursuant to Exemption No. 76EL-01DOD issued on July 26, 1976. This
product should not be used without adequate protective devices or procedures.
FIGURE 4-2. Military Laser Exemption Label

4-3.3 LASER RANGE AND BUILDING WARNING SIGNS. Warning signs, as specified in
section 4.7 of ANSI Z136.1, shall be posted at the entrances to laser ranges and buildings in
accordance with sections 4.3.9, 4.3.10, 4.3.11, and 4.3.12 of ANSI Z136.1.
4-3.4 For all invisible radiation (less than 400 nanometers or greater than 700 nanometers) the
word "invisible" shall precede the word "radiation" on all warning signs and labels. Each class
II, III, and IV laser product which is not military exempt must state the maximum power output of
laser radiation, the pulse duration when appropriate, and the laser medium or emitted
wavelength on the warning label attached to the device.
4-3.5 Laser safety warning signs for posting at laser facilities and at laser ranges are stocked at
the Naval Inventory Control Point, Naval Publication and Forms Branch, 700 Robbins Avenue,
Philadelphia, PA 19111-5098. For information concerning these forms, contact (215) 697-2626
or DSN 442-2626.
4-4.
TRAINING
All personnel in areas using lasers shall be informed about the potential hazard
associated with accidental exposure to this form of radiation. In particular, the extraordinary
danger of eye damage due to the optical amplification and efficient absorption by this organ
shall be emphasized. Class III and IV lasers may also cause skin damage or damage to
material by fire or explosion due to rapid heating from a focused beam. At a minimum, laser
safety training shall include the requirements of OPNAVINST 5100.27/MCO 5104.1 (series).
4-5.
MEDICAL SURVEILLANCE
Bureau of Medicine and Surgery Instruction (BUMEDINST) 6470.23 (series) gives

medical surveillance requirements and casualty management procedures for personnel
exposed to laser radiation.
4-6.
COMMAND LASER SAFETY PROGRAM
4-6.1 When required [based upon type of laser(s) employed], each command should establish
a laser safety program and appoint a laser safety officer as per OPNAVINST 5100.27/MCO
5104.1 (series) and ANSI Z136.1.
4-5

4-6.2 When required, a laser safety officer shall be appointed to coordinate the safety aspects
of lasers and their use. This appointment shall be contingent on the successful completion of
laser safety officer training as described in OPNAVINST 5100.27/MCO 5104.1 (series).
4-7. CALCULATION OF LASER SAFE DISTANCES AND PERMISSIBLE LASER
EXPOSURE LEVELS
Methods to calculate laser safe distances and permissible laser exposure levels are
specified in appendix B of ANSI Z136.1. As per OPNAVINST 5100.27/MCO 5104.1 (series),
only certified Laser Safety Specialists may make such calculations. The Navys primary point of
contact for making these calculations is Naval Surface Warfare Center, Dahlgren Division
(G71). See paragraph 4-8.1 for laser technical assistance information.
4-8.
LASER TECHNICAL ASSISTANCE
4-8.1 Interested parties may obtain technical assistance and advice regarding laser safety by
accessing the official Navy Web site (www.navylasersafety.com) or by contacting:
a. For medical and industrial laser operations: Navy Environmental Health Center,
620 John Paul Jones Circle, Suite 1100, Portsmouth, VA 23708-2103, (757) 953-0700,
(757) 621-1967, DSN 377-0700, or DSN 377-1967.
b. For laser systems and certification surveys of laser firing ranges (funding for
services shall be provided by the requesting command):
1. Laser Hazard Evaluations and Range Surveys: Commander, Naval Surface
Warfare Center, Dahlgren Division (G71), 17320 Dahlgren Road, Dahlgren, VA 22448-5100,
(540) 653-1060/1149, DSN 249-1060/1149, fax (540) 653-8453, www.navylasersafety.com.
2. Laser Range Surveys: Commander, Naval Surface Warfare Center, Corona
Division (SE41), P.O. Box 5000, Corona, CA 92878-5000, (909) 273-4142 or DSN 933-4142.
c. For laser bioeffects and medical research issues, or assistance in evaluating laserinduced injuries, contact the Naval Health Research Center-Detachment Brooks AFB, 8301
Navy Road, Brooks AFB, TX 78235-5365, (210) 536-4699/6552, DSN 240-4699/6552, or fax
(210) 536-6439/6528.
d. For guidance on laser exposure limits and health issues, contact the Non-Ionizing
Radiation Health Branch, Bureau of Medicine and Surgery (MED 212), 2300 E Street NW,
Washington, DC 20372-5300, (202) 762-3444, DSN 762-3444, or fax (202) 762-0931.
4-8.2 Naval Sea Systems Command (SEA-00T) is the technical lead agent for all Navy/Marine
Corps laser safety. Naval Surface Warfare Center, Dahlgren Division (G71), is the lead Navy
technical laboratory for all technical issues pertaining to lasers used in, by, and for the Navy and
Marine Corps.
4-6

CHAPTER 5
IONIZING RADIATION
5-1.
INTRODUCTION
Ionizing radiation is the electromagnetic or particulate emanations produced by radiation

sources. These emanations can cause ionization; that is, the ejection of electrons from atoms.
Ionization within the cells or tissues of the body can occur as the result of exposure to alpha
particles, beta particles (electrons), neutrons, protons, or other atomic or subatomic particles, or
of exposure to gamma rays, x-rays, or other electromagnetic waves capable of ejecting
electrons from atoms.
5-2.
UNITS OF MEASUREMENT
a. Electron Volt (eV) - A unit of energy equal to the energy gained by an electron in
passing from a point of low potential to a point one volt higher in potential. One eV equals
1.602x10-12 ergs (1.602x10-19 joules) of energy.
b. Rem - An equilibration of the dose of ionizing radiation to the body in terms of its
estimated biological effect, relative to an absorbed dose of 1 roentgen of high-voltage x-rays.
The rem shall be the unit of dose for record purposes.
c. Roentgen (R) - That amount of x- or gamma radiation which will produce 2.083x109
ion pairs in 1 cc of air under standard conditions. For the purpose of these regulations, 1
roentgen of x- or gamma radiation is considered to deliver 1 rad.
d. Rad - A unit of absorbed ionizing radiation equal to 100 ergs of energy per gram.
5-3.
METHODS OF DETECTING IONIZING RADIATION
Ionizing radiation cannot be detected by the senses. It can be detected only by devices
which respond to the ionizing properties of radiation. These detecting devices include Geiger
counters, scintillation counters, ionization chambers (including pocket dosimeters), phosphors,
transformation reaction counters (including photographic emulsions), and free radical counters.
5-4.
RADIAC EQUIPMENT
The purpose of radiac equipment is to detect and indicate the amount of radioactivity
present in a given area. The type of radioactivity detected (alpha and beta particles, x-ray,
gamma radiation, fast and slow neutrons) is determined by the type of radiac equipment used.
Radiac equipments vary from small, portable, battery-operated sets to large, integrated
monitoring systems requiring associated electronic equipment. Basically, radiac equipments
contain one or a combination of the following:
5-1

a. Radiac Detector - A device that is sensitive to radioactivity of free nuclear particles
and reacts in a manner that can be interpreted or measured by various means.
b. Radiacmeter - A device that detects the presence of radioactivity and indicates the
dose rate or total dose.
c. Computer-Indicator - A device that computes and indicates radiac data received from
the radiac detector or detectors.
5-5.
HAZARD LEVEL
All personnel working in high-intensity levels of radioactivity must exercise caution to

prevent bodily damage. While the radiation from radioactive substances cannot be seen or felt,
prolonged or extensive exposure may result in serious damage. One-tenth of a roentgen per
week (0.1 R/week or 100 mR/week) is considered to be the maximum permissible exposure.
5-6.
PRECAUTIONS
5-6.1. Safety precautions and instructions on handling radioactive material are contained in
Naval Medical Command (NAVMED) Publication P-5055, Radiation Health Protection Manual,
and various National Institute of Standards and Technology handbooks.
5-6.2. Precautions should be taken not to attempt any measurement of ionic radiation while
located in a radio-frequency (RF) electromagnetic field. Radiac detectors are susceptible to
electromagnetic fields and will produce an erroneous reading which could be mistaken for ionic
radiation. The reverse is also true. Do not attempt to measure RF radiation while in the
environment of ionic radiation.
5-6.3. The accumulated dose of radiation to the whole body, head and trunk, active bloodforming organs, genitals, or lens of the eye shall not exceed 3 rem in any calendar quarter nor 5
(N-18) rem total lifetime dose, where N equals the present age in years.
5-2

CHAPTER 6
HAZARDS OF ELECTROMAGNETIC RADIATION TO FUEL
6-1.
INTRODUCTION AND BACKGROUND
6-1.1. A fuel-handling operation is defined as the act of transferring fuel from one container to
another. This includes, but is not limited to, fueling aircraft, vehicles, or equipment from a pump
or a portable container; transferring fuel from a storage container to a fuel truck; and transferring
fuel from a pump to a portable container. While fixed shore-station antennas are usually located
a sufficient distance from fuel pumps and fuel storage areas in order to prevent a hazard, care
should be taken to ensure that fueling operations involving transfer of fuel from a portable
container to a vehicle or equipment (such as lawnmowers, generators, construction equipment,
etc.) do not occur within the prescribed safe separation distances for shore-station transmitters
if main-beam illumination of the area is possible. In addition, mobile and handheld transmitters
should not be operated within the minimum safe separation distance from any fuel-handling
operation.
6-1.2. The possibility of accidentally igniting fuel vapors by radio frequency (RF)-induced arcs
during fuel-handling operations in proximity to high-powered communication and radar
transmitting antennas has been the subject of extensive study and research. Tests aboard
ships and in laboratories have shown that, while it is possible to ignite volatile fuel-vapor
mixtures by induced RF energy, the probability of ignition during normal fueling procedures is
remote, given the number of conditions that must exist simultaneously in order to support
combustion.
6-1.3. The probability of accidental ignition has been reduced in recent years by the following:
a. Location of transmitting antennas away from fueling stations and vents.
b. Introduction of pressurized fueling systems on aircraft.
c. The move to almost exclusive use of JP-5 aircraft fuels aboard ship.
Even though the potential fuel hazard from electromagnetic radiation may not be as great as
formerly believed and has been reduced by the foregoing measures, it is still present when
handling the more volatile JP-4 fuel, motor vehicle gasoline (MOGAS), or aviation gasoline
(AVGAS). Personnel handling fuels afloat and ashore should be aware of this potential hazard,
which is more fully described herein.
6-2.
PHYSICAL NATURE OF COMBUSTION
6-2.1. The probability of ignition of fuel vapors by RF-induced arcs is small, since the following
conditions must occur simultaneously for ignition to take place:
6-1

a. A flammable fuel-air mixture must be present within range of the induced arcing.
b. The arc must contain a sufficient amount of energy to cause ignition.
c. The gap across which the arc occurs must be a certain minimum distance.
6-2.2. The limits of flammability of MOGAS are between 1.25 percent and 7.6 percent by
volume of gasoline vapor in the air. Handling of gasoline under normal operating conditions
does not produce a flammable atmosphere except close to fuel vents, open fuel inlets, or spilled
gasoline. With no ventilation, flammable gasoline vapors, being heavier than air, may travel or
spill down an inclined surface, such as that provided by a wing or fuselage of an aircraft, before
becoming diluted. However, if air movement (wind) is present, the gasoline vapor is diluted and
dispersed rapidly, reducing the zone of possible ignition. The flammability of hydrocarbon fuels
is also influenced by temperature. Figure 6-1 shows the effect on flammable ranges due to
increasing fuel temperatures. Figure 6-2 shows the temperature-flammability regions for
different types of commonly used fuels.
FIGURE 6-1. Effect of Temperature in Generating Hydrocarbon Fuel Flammable Vapors

6-2

FIGURE 6-2. Temperature-Flammability Ranges for Fuels

6-2.3. The presence of an odor of gasoline is not a reliable indicator of flammability since the
effect of odorous substances varies among observers. However, in comparative tests of
6-3

individual response, it was found that the odor of gasoline was quite perceptible at
concentrations of less than 1 percent of the lower flammability limit. At 100 percent, a very
strong odor existed; at 125 percent, the gas-air mixture was noticeably irritating to the eyes and
nasal passages.
6-2.4. Although tests conducted under laboratory conditions to determine the minimum arc
energy necessary to cause ignition have been inconclusive, it is known that the arc energy is a
determining factor for ignition of fuel-air mixtures. From actual measurements of voltages and
currents on aircraft located on a carrier deck near an energized transmitting antenna, it was
found that a volt-ampere product of 50 or more was required to ignite gasoline in an explosive
vapor test device. Measurements also have been made on various fueling configurations to
relate the required 50 volt-ampere ignition energy to the surrounding electric field intensity.
Field intensity can, in turn, be related to the radiated power and distance from an antenna.
6-2.5. A minimum spark gap of about 0.5 millimeter (0.02 inch) is required for ignition of a fuelair mixture. In terms of fueling operations, this generally requires a metal-to-metal contact and
subsequent withdrawal to produce a drawn arc of sufficient length to ignite a fuel-air mixture.
Ensuring that the static ground wires, tie-down cables, and other metallic connections to the
aircraft or motor vehicle are properly made before fueling or defueling operations commence,
and are not disturbed until after the operation is finished, will greatly reduce the possibility of
accidental ignition.
6-3.
HANDLING PRECAUTIONS FOR FUELS IN AN RF ENVIRONMENT
6-3.1 INTRODUCTION. It is assumed that personnel engaged in fueling operations will be

familiar with and observe the safety precautions contained in applicable Naval Sea Systems
Command/Naval Air Systems Command instructions and directives.
Three hydrocarbon-based fuels are currently used throughout the Navy: marine diesel,
aviation jet fuel (JP-5/JP-8), and MOGAS. Of these, only MOGAS is considered to present a
shipboard hazards of electromagnetic radiation to fuel (HERF) concern during fuel-handling
operations.
6-3.2 FUELING PRECAUTIONS. The total elimination of RF-induced arc hazards to fuels
probably cannot be achieved, particularly aboard ship, without placing unacceptable restrictions
on flight and ship operations. Although precise criteria have not been fully developed, the
following guidance, applicable to fueling operations both afloat and ashore, will minimize the
risk of accidental ignition. This guidance shall govern in the event of conflict with other
directives.
a. Do not energize any transmitter (radar or communications) on the aircraft or motor
vehicle being fueled or on adjacent aircraft or motor vehicles.
b. Do not make or break any electrical, static ground wire, tie-down connection, or any
other metallic connection to the aircraft or motor vehicle while it is being fueled. Make the
connections before fueling commences; break them afterwards.
6-4

6-3.3 TRANSMITTER RESTRICTIONS. JP-5 and marine diesel fuels are used and stored in
large quantities aboard ships and at shore stations. There are no HERF issues associated with
these fuels since their vapor pressures are low enough that, under ordinary temperatures, there
is virtually no chance of fire from an RF-induced arc. However, highly volatile MOGAS is also
handled and stored aboard most Navy ships and at shore facilities.
The following precautions and RF transmitter restrictions are required (1) during
shipboard fuel-handling operations involving MOGAS and (2) during shore-based fuel-handling
operations involving MOGAS and/or AVGAS.
6-3.4. Radar and communication systems which operate at or above 225 MHz, and which are
capable of mainbeam illumination of fuel-handling areas with a peak power density of 5 W/cm2
(5000 mW/cm2) or greater, shall:
a. cease transmitting during fueling operations,
b. be inhibited from illuminating these areas by suitable cutout devices or operational
procedures, or
c. be located a sufficient distance from fueling areas such that the power density (in the
fueling area) is less than 5 W/cm2.
Figure 6-3 provides a means to calculate the minimum distance required to achieve a
power density of 5 W/cm2. A separation distance in excess of this number should be
established to ensure that the power density in the fueling area is less than 5 W/cm2.
6-3.4.1 For fixed, mobile, and aircraft communication systems which operate below 225 MHz:
a. Antennas radiating 250 watts or less shall be installed no less than 50 feet from
fueling operations/fuel-handling areas.
b. Antennas radiating more than 250 watts shall be separated from fueling/fuel-handling
areas such that the power density in the fueling area is no greater than would exist at 50 feet
from an antenna radiating 250 watts (0.009 mW/cm2).
If the required separation distance/power density cannot be achieved, the transmitter shall be
shut down during fueling/fuel-handling operations.
Figure 6-4 provides the means to calculate the separation distance required to achieve a
power density equivalent to that existing 50 feet from an antenna radiating 250 watts
(0.009 mW/cm2).
6-3.4.2 For handheld communication transmitters, antennas radiating 10 watts or less shall
remain at least 10 feet away from fueling/fuel-handling operations.
6-5

The following equation may be used to calculate the distance from a transmitting antenna where the power
density will be approximately 5 W/cm2. A separation distance greater than that calculated should be established
to ensure that the power density in the fueling area will be less than 5 W/cm2.
PGPG - = -----------D = --------------4PD 792.7

where:
D = distance (meters),
P = peak transmitter power (watts),
gain (in dBi) ),
,
G = antenna gain ratio= (10antenna 10
= numeric value of 3.14159 (pi),

PD = desired power density (in W/m2) = 5 W/cm2 = 50,000 W/m2.
Example
Calculate how far the antenna for the AN/SPS-48E radar (2905-3058 MHz) must be from the fueling area to
ensure that the (main beam) power density in the fueling area does not exceed 5 W/cm2.
P = 2,500,000 watts
Antenna Gain = 38.6 dBi
)
antenna gain ratio=(1038.6
10
= ( 103.86) = 7244.4
2, 500, 000 ( 7244.4 )

D = ---------------------------------------------------792.7
18, 110, 899, 000
D = ---------------------------------------------792.7
134576.7
D = ---------------------- = 169.8 meters 3.28 = 557.0feet (see note)
792.7
NOTE: This derived value represents the minimum distance from the main beam of the SPS-48E radar required
to achieve a power density of 5 W/cm2. In the case of shipboard radar systems, since the main beam does not
typically illuminate own-ship fueling areas or weather decks, power densities in these areas will be less than 5 W/
cm2. However, during operations with other surface units (i.e., UNREP, plane guard), emission control
procedures may be required between participating units to ensure that the (main beam) power density existing at
topside fuel-handling areas is less than 5 W/cm2 during fueling operations.
Ashore, the location of fixed and mobile radar/communication systems relative to fueling/fuel-handling areas must
be determined/controlled to ensure that the main beam power density in those areas is less than 5 W/cm2 during
fuel-handling operations. RF hazard surveys may be requested as discussed in paragraph 1-5.c., of this manual.
FIGURE 6-3. HERF Safe Separation Distance Calculation for MOGAS/AVGAS

(Radar and Communication Systems 225 MHz and Above)
6-6

The following equation may be used to calculate the separation distance required to achieve a power density
equivalent to that existing 50 feet from an antenna radiating 250 watts (equivalent to 0.009 mW/cm2 or
0.09 W/m2).
PGPG - = ----------D = --------------1.06

4PD
where:
D = distance (meters),
P = peak transmitter power (watts),
gain (in dBi) ),
G = antenna gain ratio= (10antenna 10
,
= numeric value of 3.14159 (pi),

PD = desired power density (in W/m2) = 0.09 W/m2.
Example
Calculate how far an antenna for the AN/URC-131 transmitter (2-30 MHz) must be from the fueling area to ensure
that the power density in the fueling area does not exceed 0.09 W/m2. A greater separation distance will provide
an increased margin of safety.
P = 1,000 watts
Antenna Gain = 2.1 dBi
antenna gain ratio=(102.1
)
10
= ( 10.21) = 1.62
1, 000 ( 1.62 )
D = ---------------------------------1.06
1620
D = ---------------1.06
40.25
D = ------------- = 37.9 meters 3.28 = 124.5feet
1.06
FIGURE 6-4. HERF Safe Separation Distance Calculation for MOGAS/AVGAS

(Communication Systems Below 225 MHz)
6-7/(6-8 Blank)

APPENDIX A
DEFINITIONS AND ABBREVIATIONS
A-1. INTRODUCTION.
This appendix contains definitions of terms and abbreviations related to radio-frequency
(RF) radiation hazards to personnel, volatile flammable liquids, and ordnance. In addition, the
terms and abbreviations used in the laser radiation hazard coverage are contained herein.
A-2. DEFINITIONS.
Antenna - That part of a transmitting or receiving system which is designed to radiate or to
receive electromagnetic waves.
Antenna, Dipole - A straight radiator, usually fed in the center, and producing a maximum
of radiation in the plane normal to its axis. The length specified is the overall length. Common
usage considers a dipole antenna to be a metal radiating structure which supports a line current
distribution similar to that of a thin straight wire a half wavelength long, so energized that the
current has two nodes, one at each of the far ends.
Antenna Directivity - The ratio of the maximum radiation intensity to the average radiation
intensity produced at a given distance from a given transmitting antenna. The directivity of an
antenna is the same whether the antenna is used as a receiving antenna or a transmitting antenna.
Antenna Gain, Relative - The ratio of the power gain of an antenna relative to a standard
reference antenna. The relative gain may be in dB or it may be numeric. The standard antenna
is usually a half-wave dipole or an isotropic antenna. The latter is preferred even though such
an antenna does not exist. (See Isotropic Antenna.)
Antenna Regions - The defined spatial areas surrounding a radiating antenna.
Arc - An electrical discharge of relatively long duration which may be brought about by
separating current-carrying electrodes or may result from a spark discharge between initially
separated electrodes, provided that the energy source is sufficient to maintain the arc.
Attenuation - A decrease in signal magnitude in transmission from one point to another
expressed as a ratio or in decibels.
Attenuator - A device for reducing the amplitude of electromagnetic energy without
introducing appreciable distortion.
Average Power (W) - The time-average rate of energy transfer:
1 2
W = -------------- W ( t ) dt .
t2 t1 1
A-1

For radar calculations, average power (W) = peak power x pulse width x pulse repetition
frequency.
Averaging Time (Tavg) - The appropriate time period over which exposure is averaged for
purposes of determining compliance with a permissible exposure limit.
Beam - A flow of electromagnetic radiation or of particles that is essentially unidirectional.
Beamwidth - The angular width between half-power points on the major lobe of an antenna
radiation pattern for a specified plane.
Computer-Indicator - A device that computes and indicates radiac data received from the
radiac detector or detectors.
Continuous Exposure - Exposure for durations exceeding the corresponding averaging
time. Exposure for less than the averaging time is called short-term exposure.
Continuous Wave - Waves, the successive oscillations of which are identical under steadystate conditions.
Controlled Environment - A location where exposure to electromagnetic energy in excess
of the permissible exposure limits (PELs) specified for the general population may be incurred
by persons who are aware of the potential for such exposure. Examples of controlled
environments include radar and communication equipment spaces and the flight deck and
weather decks of a ship. PELs for controlled environments are listed in tables C-1 and C-2.
Cryogenics - Relating to the production of very cold temperatures.
Decibel (dB) - A dimensionless unit which is a measure of the ratio of two powers. The
number of decibels, n, corresponding to the ratio of powers P1 and P2 is as follows:
P1
n = 10log 10 ------ .
P2
If conditions are such that the ratio of current I1/I2 or voltages V1/V2 (or analogous quantities) is
the square root of the corresponding power ratio, then the number of dB by which the
corresponding powers differ is expressed by the following equations:
P1
I1
n = 10log 10 ------ = 20 log 10 ---- or
P2
I2
P1
V1
n = 10log 10 ------ = 20 log 10 ------ .
P2
V2
Depth of Penetration - For a plane electromagnetic wave incident on the boundary of a
medium, the distance from the boundary into the medium along the direction of propagation in
the medium, at which the field strengths of the wave have been reduced to 1/e (e=2.7183) of the
boundary values.
A-2

Duty Cycle - The ratio of pulse duration to the pulse period of a periodic pulse train. A duty
factor of 1.0 corresponds to continuous-wave operation.
Effective Area - The effective area of an antenna in any specified direction is equal to the
square of the wavelength multiplied by the power gain (or directive gain) in that direction and
divided by 4. That is:
2
G
A = ---------- .
4
Electric Field (E) - A state of the region in which stationary charged bodies are subject to
forces by virtue of their charges.
Electric Field Strength (E) - The magnitude of the electric field vector. The electric field
strength represents the magnitude of the electric force (F) on a positive test charge (q) at a point
divided by the charge:
F
E = --- .
q
Electric field strength is expressed in units of V/m.
Electromagnetic Energy - The energy in an electromagnetic wave or field.
Electromagnetic Environment (EME) - The composite electromagnetic field generated by
natural and manmade sources.
Electromagnetic Radiation (EMR) - Emission of energy in the form of electromagnetic
waves in any portion of the electromagnetic spectrum.
Electromagnetic Wave (EMW) - A wave characterized by variations of electric and magnetic
fields. EMWs are known as radio waves, heat rays, light rays, etc., depending on the frequency
at which the field varies.
Electron Volt (eV) - A unit of energy equal to the energy gained by an electron in passing
from a point of low potential to a point one volt higher in potential. One eV equals 1.602x10-12
ergs (1.602x10-19 joules) of energy.
Electronic Equipment - Equipment which produces useful internal signals, or serves
functionally by generating, transmitting, receiving, storing, processing, or using information in the
broadest sense. Examples are communications, radar, sonar, countermeasures, navigation,
computers, test equipment, etc.
10-7
Erg - The unit of work and of energy in the centimeter-gram-second systems. The erg is
joule.
Exposure - The subjection of a person to electric, magnetic, or electromagnetic fields or to

contact currents other than those originating from physiological processes in the body and other
natural phenomena.
A-3

Far-Field Region - That region of the field of an antenna where the angular field distribution
is essentially independent of the distance from the antenna. In this region (also called the freespace region), the field has a predominantly plane-wave character; i.e., locally uniform
distributions of electric field strength and magnetic field strength in planes transverse to the
direction of propagation which decay inversely (1/r) with distance r from the antenna. For aperture
antennas, the far-field region is also referred to as the Fraunhofer region. Refer to appendix D.
Field Intensity - The measure of the magnitude of an electromagnetic field. For
communication frequencies (200 kHz to 1.0 GHz), field intensity is a measurement of the electrical
field component expressed in V/m. For radar frequencies (200 MHz to 100 GHz), field intensity
is a measurement of the average power density expressed in mW/cm2.
Flammable - A relative term that applies to liquids, gases, and solids, indicating that they
are easily ignited in air.
Flammable Limits (Flammability Limits) - The minimum and maximum concentration of a
vaporized material in air which will propagate flame if ignited. The difference between the upper
and lower flammability limit is known as the flammable or explosive range. The limits are usually
expressed in terms of percentage of vapor by volume in air.
Fraunhofer Region - See Far-Field Region.
Frequency Spectrum - Range of frequencies of electromagnetic energy from both natural
phenomena and manmade sources; generally extends from less than 0.001 Hz to greater than
1022 Hz. The radio-frequency spectrum is, loosely, that portion of the total spectrum used for
information communication.
Fresnel Region - See Near-Field Region.
Hertz (Hz) - The unit of frequency, one cycle per second.
Horn Antenna - An antenna having the shape of a tube whose cross-sectional area
increases toward the open end through which radio waves pass.
Infrared - Electromagnetic waves in the approximate frequency range of 3x1011 to 4x1014
Hz (wavelength: 700 nm to 1 mm).
Ionizing Radiation - Electromagnetic waves with sufficient energy to produce ions; usually
x-ray frequencies and higher.
Isotropic Antenna - A hypothetical (lossless) antenna having equal radiation intensity in all
directions. Isotropic antennas do not exist physically but represent a convenient means of
expressing directional properties of actual antennas.
Joule - The unit of energy in the metric system. One joule is equivalent to 1 watt/second.
Magnetic Field Strength (H) - A field vector that is equal to the magnetic flux density divided
by the permeability of the medium. Magnetic field strength is expressed in units of A/m.
Magnetic Flux Density (B) - A field vector quantity that results in a force (F) acting on a
charge(s) (q) moving with velocity (v). Magnetic flux density (B) is defined by the following
equation:
A-4

F
--- = ( v B ) .
q
Magnetic flux density is expressed in units of tesla (T). One tesla is equal to 104 gauss (G).
Main Beam of Radar - The "main beam" as used herein refers to the solid angular arc
describing the maximum radiation lobe of the radar, outside of which the power level is at least
20 dB below the maximum power level radiated.
Maximum Permissible Exposure (MPE) for Lasers - The maximum radiation (for a given
laser) to which a person can be exposed without adverse biological effect to the eye or skin. The
MPE is determined by three factors: laser wavelength, laser energy during exposure, and duration
of the exposure. MPE values for the eyes and skin are listed in table 5 and table 7 of ANSI
Z136.1-2000.
Microwaves - A term used rather loosely to identify radio waves in the frequency range of
300 MHz to 300,000 MHz.
Near-Field Region - A region generally in proximity to an antenna or other radiating structure
in which the electric and magnetic fields do not have a substantially plane-wave character, but
vary considerably from point to point. The near-field region is further subdivided into the reactive
near-field region, which is closest to the radiating structure and contains most or nearly all of the
stored energy, and the radiating near-field region, where the radiation field predominates over
the reactive field but lacks substantial plane-wave character and is complicated in structure. For
aperture antennas, the near-field region is also referred to as the Fresnel region. Refer to
appendix D.
NOTE
For most antennas, the outer boundary of the reactive near-field
region is commonly taken to exist at a distance of one-half
wavelength from the antenna surface.
Permissible Exposure Limit (PEL) - The peak electric and magnetic field strengths (or
associated plane-wave equivalent power densities) and the induced and contact currents to which
a person may be exposed without harmful effects, even under repeated or long-term exposure
conditions. In controlled environments, the PEL is based on maintaining exposure below a
specific absorption rate (SAR) of 0.4 W/kg. That level incorporates a safety factor of 10 below a
SAR of 4 W/kg that is considered a threshold, above which there is an increasing possibility of
adverse biological effects, but at or below which there is no established evidence of any adverse
health effects. In uncontrolled environments, where personnel access is not restricted, lower
levels (equivalent to a SAR of 0.08 W/kg) have been adopted.
Polarization - Term used to describe the orientation of a time-varying electric or magnetic
field vector. If the vector is confined to a plane containing the direction of propagation as an axis
but remains constant in magnitude, the wave is circularly polarized. If the amplitude does not
remain constant, so that the end of the vector traces out an ellipse, the wave is elliptically
polarized.
A-5

Power Density (S) - Power per unit area normal to the direction of propagation, usually
expressed in units of watts per square meter (W/m2) or, for convenience, units such as milliwatts
per square centimeter (mW/cm2) or microwatts per square centimeter (W/cm2). For plane
waves, power density, electric field strength (E), and magnetic field strength (H) are related by
the impedance of free space; i.e., 377.
Power Density, Peak - The maximum instantaneous power density occurring when power
is transmitted.
Power Density, Plane-Wave Equivalent - A commonly used term associated with any
electromagnetic wave, equal in magnitude to the power density of a plane wave having the same
electric (E) or magnetic (H) field strength.
Rad - A unit of absorbed ionizing radiation equal to 100 ergs of energy per gram.
Radar - Equipment which radiates directional electromagnetic waves and uses the
reflection of such waves from distant objects to determine their existence or position. The name
is derived from the initial letters of the expression RAdio Detection And Ranging. As used in this
manual, radar includes countermeasures, navigational, and other similar types of electronic
equipment.
Radiac - An acronym derived from the words "RadioActivity, Detection, Indication And
Computation" and used as an all-encompassing term to designate various types of radiological
measuring instruments or equipment.
Radiac Detector - A device that is sensitive to radioactivity of free nuclear particles and
reacts in a manner that can be interpreted or measured by various means.
Radiacmeter - A device that detects the presence of radioactivity and indicates the dose
rate or total dose.
Radiated Field - That portion of the total electromagnetic field produced by a currentcarrying conductor or aperture, the magnitude of whose electric or magnetic vector varies
inversely as the distance from the conductor, and the energy of which is propagated away from
the conductor. This region is made up of two distinct parts: the Fresnel or near-field region and
the Fraunhofer or far-field region. The distinction between near-field and far-field regions has no
practical meaning for small radiators but is extremely important for large antennas.
Radiation Hazards (RADHAZ) - Radio-frequency electromagnetic fields of sufficient
intensity to produce harmful biological effects in humans, cause spark ignition of volatile
combustibles, or actuate electroexplosive devices.
Radio Frequency (RF) - A frequency between 3 kHz and 300 GHz used for radio and radar
transmission.
NOTE
Although the RF spectrum is formally defined in terms of frequency
as extending from 0 to 3000 GHz, for purposes of this standard, the
frequency range of interest is 3 kHz to 300 GHz.
A-6

Rem - An equilibration of the dose of ionizing radiation to the body in terms of its estimated
biological effect, relative to an absorbed dose of 1 roentgen of high-voltage x-rays. The rem shall
be the unit of dose for record purposes.
RF Burn - A radio-frequency (RF) burn hazard exists if there is sufficient induced RF voltage
on a metallic object to cause pain, visible skin damage, or involuntary reaction to a person who
comes in contact with the object. The RF burn phenomenon is distinct from electrical shock and
is the result of heating of the skin by RF currents.
Roentgen (R) - That amount of x- or gamma radiation which will produce 2.083 x 109 ion
pairs in 1 cc of air under standard conditions. For the purpose of these regulations, 1 roentgen
of x- or gamma radiation is considered to deliver 1 rad.
Root Mean Square (rms) - The effective value, or the value associated with joule heating,
of a periodic electromagnetic wave. The rms value is obtained by taking the square root of the
mean of the squared value of a function.
Shielding - A housing, screen, or other object, usually conductive, that substantially reduces
the magnitude of electric or magnetic fields on one side thereof, upon devices or circuits on the
other side.
Spark - An electrical discharge of relatively short duration between initially separate
electrodes; the discharge may be repetitive.
Spatial Average - The root mean square of the field over an area equivalent to the vertical
cross section of the adult human body, as applied to the measurement of electric or magnetic
fields in the assessment of whole-body exposure. The spatial average is measured by scanning
(with a suitable measurement probe) a planar area equivalent to the area occupied by a standing
adult human (projected area). In most instances, a simple vertical, linear scan of the fields over
a 2-meter height (approximately 6 feet), through the center of the projected area, will be sufficient
for determining compliance with the permissible exposure limits.
Specific Absorption Rate (SAR) - The time derivative of the incremental energy (dW)
absorbed by (dissipated in) an incremental mass (dm) contained in a volume (dV) of a given
density ():
d dW
d dW
SAR = ----- -------- = ----- ---------- .
dt dm dt dV
SAR is expressed in units of watts per kilogram (W/kg).
Specular Reflection - A mirrorlike reflection.
Static Region - The region around a current-carrying conductor where the magnitude of the
electromagnetic field varies inversely as the cube of the distance from the conductor, the energy
of which returns to the conductor when the current ceases. The static region is part of the near
field of an antenna.
Thermal Effect - Generally refers to the heating effects of electromagnetic radiation on
materials and people.
A-7

Ultraviolet - Electromagnetic waves in the approximate frequency range of 7x1014 to 3x1016
Hz (wavelength: 180 nm to 400 nm).
Uncontrolled Environment - Locations where personnel access is uncontrolled, and where
radio-frequency (RF) exposures do not exceed the permissible exposure limits specified in tables
C-3 and C-4. Such locations generally represent living quarters, workplaces, and public access
areas where personnel do not expect to encounter higher levels of RF energy.
Volatile - A relative term which indicates the tendency of a liquid or solid to assume the
vapor state (evaporate).
Wavelength () - Of a monochromatic wave, the distance between two points of
corresponding phase of two consecutive cycles in the direction of propagation. The wavelength
() of an electromagnetic wave (EMW) is related to the frequency (f) and velocity (v) by the
expression =v/f. In free space, the velocity of an EMW is equal to the speed of light; i.e.,
approximately 3x108 m/s.
Whole-Body Irradiation - Pertains to the case in which the entire body is exposed to the
incident electromagnetic energy or in which the cross section of the body is smaller than the cross
section of the incident radiation beam.
X-Radiation - Electromagnetic radiation of short wavelength (less than 100 D), usually
produced by the bombardment of a metal target by high-energy electrons.
A-3. ABBREVIATIONS.
A/m - Amperes per Meter
ANSI - American National Standards Institute
AVGAS - Aviation Gasoline
BLK - Block
BUMED - Bureau of Medicine and Surgery
BUMEDINST - Bureau of Medicine and Surgery Instruction
cc - Cubic Centimeter
CFR - Code of Federal Regulations
cm - Centimeter
cm2 - Square centimeters
CO2 - Carbon Dioxide
dB - Decibel
dBd - dB Relative to Dipole Antenna
A-8

dBi - dB Relative to Isotropic Antenna
dBm - Decibel Referred to 1 Milliwatt
dBW - Decibel Referred to 1 Watt
DoD - Department of Defense
DODINST - Department of Defense Instruction
DSN - Defense Switching Network
E-field - Electric Field
EMCON - Emission Control
EMR - Electromagnetic Radiation
EMW - Electromagnetic Wave
eV - Electron Volt
f - Frequency
FDA - Food and Drug Administration
FM - Frequency Modulation
ft - Feet
GHz - Gigahertz (1,000 MHz to 109 Hz)
HERF - Hazards of Electromagnetic Radiation to Fuel
HERO - Hazards of Electromagnetic Radiation to Ordnance
HERP - Hazards of Electromagnetic Radiation to Personnel
HF - High Frequency (3-30 MHz)
H-field - Magnetic Field
HP - Hewlett Packard
hr - Hour
Hz - Hertz
IEEE - Institute of Electrical and Electronics Engineers
kg - Kilogram
kHz - Kilohertz (103 Hz)
A-9

kW - Kilowatt (103 watts)
Laser - Light Amplification by Stimulated Emission of Radiation
LSRB - Laser Safety Review Board
m or M - Meter(s)
mA - Milliampere (10-3 ampere)
MCO - Marine Corps Order
MHz - Megahertz (106 Hz)
min - Minutes
MK - Mark
mm - Millimeter
MOGAS - Motor Gasoline (i.e., automotive gasoline)
MPE - Maximum Permissible Exposure
mR - Milliroentgen
MW - Megawatt (106 watts)
mW - Milliwatt (10-3 watt)
mW/cm2 - Milliwatts per Square Centimeter
N2 - Nitrogen
N/A - Not Applicable
NAVAIR - Naval Air Systems Command
NAVMEDINST - Naval Medical Command Instruction
NAVSEA - Naval Sea Systems Command
nm - Nanometer
NSN - National Stock Number
OPNAV - Chief of Naval Operations
OPNAVINST - Chief of Naval Operations Instruction
PD - Power Density
A-10

PEL - Permissible Exposure Limit
R - Roentgen
Radar - RAdio Detection And Ranging
RADHAZ - Radiation Hazards
Radiac - RadioActivity, Detection, Indication And Computation
rev - Revolutions
RF - Radio Frequency
RFR - Radio Frequency Radiation
rms - Root Mean Square
rpm - Revolutions per Minute
SAR - Specific Absorption Rate
sec - Second(s)
SECNAV - Secretary of the Navy
SPAWAR - Space and Naval Warfare Systems Command
TAF - Time Averaging Factor
TAI - Time Average Interval
TX - Transmitter
TXPD - TX Power Density
UHF - Ultrahigh Frequency (300 MHz to 3 GHz)
VHF - Very High Frequency (30 to 300 MHz)
V/m - Volts per Meter
W - Watt
w/ - With
W/kg - Watts per Kilogram
A-4. SYMBOLS.
@ - At
- Alpha particle
A-11

D - Angstrom
- Density, resistivity
- Micro (10-6)
- Ohm
- 3.14159 (pi)
- Varies directly as; is proportional to
- Wavelength
= - Equals
- Is identical with
B- Is approximately equal to
~ - Is similar to
< - Is less than
> - Is greater than
# - Is less than or equal to
- Plus or minus
% - Percent
- Degree(s)
" - Inches
A-12

APPENDIX B
REFERENCE DOCUMENTS
ANSI Document
Z136.1-2000
American National Standard for the Safe Use of Lasers
BUMED Instructions
6470.23 (series)
Medical Management of Non-Ionizing Radiation

Casualties
CFR (Code of Federal Regulations)

Title 21, Subchapter J,
Regulations for the Administration and Enforcement of
Parts 1040.10 to 1040.30 the Radiation Control for Health and Safety Act of 1968
DoD Instruction
6055.11
Protection of DoD Personnel from Exposure to Radio

Frequency Radiation and Military Exempt Lasers
IEEE Standard
IEEE C95.1
1999 Edition
Safety Levels with Respect to Human Exposure to

Radio Frequency Electromagnetic Fields, 3 kHz to
300 GHz
NAVMED Instruction
P-5055
Radiation Health Protection Manual
OPNAV Instructions
5100.19 (series)
Navy Occupational Safety and Health (NAVOSH)

Program Manual for Forces Afloat
5100.23 (series)
Navy Occupational Safety and Health (NAVOSH)

Program Manual
5100.27/MCO 5104.1
Navy Laser Hazards Control Program

(series)
SECNAV Instructions
5100.14 (series)
Military Exempt Lasers
B-1/(B-2 Blank)

APPENDIX C
BIOLOGICAL EFFECTS OF ELECTROMAGNETIC RADIATION AND SAFE
EXPOSURE LIMITS
C-1.
INTRODUCTION
This appendix describes the biological effects of electromagnetic radiation (EMR) on the
human body over the frequency range of 0.003 Hz (3 kHz) to 300 GHz. The limits to which the
body can safely be exposed are specified in tables C-1 through C-4 and figures C-1 and C-2.
C-2.
FUNDAMENTAL PHYSICAL RELATIONSHIPS
Biological tissue exposed to radio-frequency (RF) energy is heated by means of

molecular agitation. Dielectric heating of biological tissue by the absorption of RF energy is the
fundamental principle of the microwave oven. It is this potential for heat generation, as well as
the possibility for tissue damage, that prompted the development of RF exposure limits.
The basic dosimetric parameter for RF exposure is the (whole-body) specific absorption
rate (SAR). The SAR is defined as the amount of energy, absorbed over an exposure time
period, divided by the total mass of the body. SAR is expressed in units of watts per kilogram
(W/kg). As specified in Department of Defense Instruction (DODINST) 6055.11, the SAR for
human exposure is set at a threshold of 0.4 W/kg for controlled environments and 0.08 W/kg for
uncontrolled environments. These levels represent a safety factor of 10. At 4 W/kg and above,
the chances for adverse biological effects increase, but below this threshold, there is no
established evidence of harm to humans.
Whole-body SAR is frequency dependent, and the resonance frequency is about
70 MHz. This resonance occurs at frequencies for which the length of the body is
approximately one-half of the free-space wavelength. The average SAR is highest when the
incident RF electric field (E-field) is nearly parallel to the human body. When a person is
standing on a perfect ground plane, his electrical length appears twice as tall compared to free
space, thus lowering the resonant frequency to one-half of free space. For incident magnetic
fields (H-fields), SAR is greater when the cross section of the body is perpendicular to the
incident H-field.
Because SAR is not a field measurement and can be measured only with laboratory-type
equipment, derived equivalent limits that are measurable with commercially available
instruments are used to determine the permissible exposure limits (PELs). PELs for controlled
and uncontrolled environments are specified in tables C-1 through C-4 and graphically as
figures C-1 and C-2. These derived equivalent limits are measurable in terms of root-meansquare (rms) E-field and H-field strengths and plane-wave equivalent power densities (S).
C-1

E-field and H-field strengths are expressed in volts per meter (V/m) and amperes per meter (A/
m), respectively, while plane-wave equivalent power densities are expressed in milliwatts per
square centimeter (mW/cm2).
Table C-1. PELs for Controlled Environments (Electromagnetic Fields)
FREQUENCY
RANGE
(MHz)
ELECTRIC
FIELD STRENGTH
(E) (V/m)
MAGNETIC
FIELD STRENGTH
(H) (A/m)
POWER
DENSITY (S)
E-FIELD, H-FIELD
(mW/cm2)
AVERAGING
TIME
2
|E| , |H|2, or S
(MINUTES)
0.003-0.1
614
163
(100, 1000000)
0.1-3.0
614
16.3/f
(100, 10000/f2)
3-30
1842/f
16.3/f
(900/f2, 10000/f2)
30-100
61.4
16.3/f
(1.0, 10000/f2)
100-300
61.4
0.163
1.0
300-3000
--
--
f/300
3000-15000
--
--
10
15000-300000
--
--
10
616000/f1.2
NOTES:
f is the frequency in MHz. The exposure values in terms of electric and magnetic field strengths are the
mean values obtained by spatially averaging the squares of the fields over an area equivalent to the vertical cross section of the human body (projected area).
These plane-wave equivalent power density values, although not appropriate for near-field conditions,
are commonly used as a convenient comparison with PELs at higher frequencies and are displayed on
some instruments in use.
Table C-2. PELs for Controlled Environments (Induced and Contact Current*, **)
FREQUENCY
RANGE
(MHz)
MAXIMUM INDUCED CURRENT (mA)
MAXIMUM CONTACT
CURRENT (mA)
THROUGH BOTH FEET
THROUGH EACH FOOT
THROUGH ONE HAND
0.003-0.
2000f
1000f
1000f
0.1-100
200
100
100
NOTES:
* f is the frequency in MHz. The current limits given may not adequately protect against startle reactions
and burns caused by transient discharges when contacting an energized object.
**In a controlled environment, access should be restricted to limit the rms RF body current (based on the
appropriate averaging time) as follows:
1) For freestanding individuals (no contact with metallic objects), RF current induced in the human body, as measured through each foot, should not exceed the following values:
C-2

NOTES (Continued):
I = 1000f mA ( for0.003 < f 0.1MHz )
where
I is the average over any 1-second period,
is the frequency in MHz.
~
I = 100f mA ( for0.1 < f 100MHz ) subject to a ceiling limit of 500 mA
~
where I is the rms current during any 6-minute period.

2) For conditions of possible contact with metallic objects, where making or breaking the contact does not result in
any momentary spark discharge or high skin-surface current density causing startle reaction, pain, burns, or
other skin injury, maximum RF currents through an impedance equivalent to that of the human body for conditions of grasping contact as measured with a contact current meter shall not exceed the following values:
I = 1000f mA ( for0.003 < f 0.1MHz )
where
~ = 100f mA ( for 0.1 < f < 100MHz ) subject to a ceiling limit of 500 mA
I
where ~
I is the rms current during any 6-minute period.
T
1
I --- I dt
T
( f 100kHz , T= 1 second)
and
T
~
1 2
I --T- I dt
1
--2
( f > 100kHz , T= 360 seconds)
The means for complying with this current limit can be determined by the user of the PEL as appropriate. The use
of protective gloves, the prohibition of metallic objects, or training of personnel may be sufficient to assure
compliance with this aspect of the PEL in controlled environments.
C-3

Table C-3. PELs for Uncontrolled Environments (Electromagnetic Fields)

FREQUENCY
RANGE
(MHz)
ELECTRIC
FIELD
STRENGTH
(E) (V/m)
MAGNETIC
FIELD
STRENGTH
(H) (A/m)
POWER
DENSITY (S)
E-FIELD, H-FIELD
(mW/cm2)
AVERAGING TIME
|E|2,S or |H|2,
(MINUTES)
FREQUENC
Y
RANGE
(MHz)
0.003-0.1
614
163
(100, 1000000)
0.1-1.34
614
16.3/f
(100, 10000/2)
1.34-3.0
823.8/f
16.3/f
(180/f2, 10000/f2)
f2/0.3
3-30
823.8/f
16.3/f
(180/f2, 10000/f2)
30
30-100
27.5
158.3/f1.668
(0.2, 940000/f3.336)
30
0.0636f1.337
100-300
27.5
0.0729
0.2
30
30
300-3000
--
--
f/1500
30
--
3000-15000
--
--
f/1500
90000/f
--
15000-300000
--
--
10
616000/f1.2
--
NOTES:
f is the frequency in MHz. The exposure values in terms of electric and magnetic field strengths are the
mean values obtained by spatially averaging the squares of the fields over an area equivalent to the vertical cross section of the human body (projected area).
These plane-wave equivalent power density values, although not appropriate for near-field conditions,
are commonly used as a convenient comparison with PELs at higher frequencies and are displayed on
some instruments in use.
Table C-4. PELs for Uncontrolled Environments (Induced and Contact Current*, **)
FREQUENCY
RANGE
(MHz)
MAXIMUM INDUCED CURRENT (mA)
MAXIMUM CONTACT
CURRENT (mA)
THROUGH BOTH FEET
THROUGH EACH FOOT
THROUGH ONE HAND
0.003-0.1
900f
450f
450f
0.1-100
90
45
45
NOTES:
* f is the frequency in MHz. The current limits given may not adequately protect against startle reactions
and burns caused by transient discharges when contacting an energized object.
** In an uncontrolled environment, where individuals unfamiliar with the phenomenon of induced RF currents may have access, it is recommended that precautions be taken to limit induced currents to values
not normally perceptible to individuals, as well as to prevent the possibility of RF burns.
C-4

NOTES (Continued):
1) For freestanding individuals (no contact with metallic objects), RF current induced in the human body, as measured through each foot, should not exceed the following values:
I = 450f mA ( for 0.003< f 0.1MHz )

where

~
I = 45 mA ( for 0.1< f < 100MHz )
subject to a ceiling limit of 220 mA
where ~
I is the rms current during any 6-minute period.
2) For conditions of possible contact with metallic objects, where making or breaking the contact does not result in
any momentary spark discharge or high skin-surface current density causing startle reaction, pain, burns, or
other skin injury, maximum RF currents through an impedance equivalent to that of the human body for conditions of grasping contact as measured with a contact current meter shall not exceed the following values:
I = 450f mA ( for 0.003< f 0.1MHz )

where

~
I = 45 mA ( for 0.1< f < 100MHz )
subject to a ceiling limit of 220 mA
where I is the rms current during any 6-minute period.

T
1
I --- I dt
( f 100kHz , T = 1 second)
and
T
~
1 2
I --T- I dt
1--2
( f > 100kHz , T = 360 seconds).
C-5
C-6
Reproduced with permission of IEEE.
FIGURE C-1.
Graphic Representation of Permissible Exposure Limits in Terms of Fields and Power Density for a
Controlled Environment
Reproduced with permission of IEEE.

FIGURE C-2.
C-7
Graphic Representation of Permissible Exposure Limits in Terms of Fields and Power Densityfor an
Uncontrolled Environment

C-3.
THERMAL EFFECTS
The heat produced by RF radiation may adversely affect live tissue. If the body cannot
dissipate this heat energy as fast as it is produced, the internal temperature of the body will rise.
Under extreme RF exposure conditions, this may result in damage to the tissue and possible
death.
The depth of penetration and coincident heating effects of RF energy on the human
tissue are frequency dependent. A transition region exists between 1 and 3 GHz. Below
1 GHz, the RF energy penetrates to the deep body tissues; above 3 GHz, the heating effect
occurs closer to the surface. At the higher frequencies, the body has an inherent warning
system in the sensory elements located in the skin. At RF frequencies between 1 and 3 GHz,
the thermal effects are subjected to varying degrees of penetration.
The bodys ability to dissipate heat successfully depends upon many related factors,
such as environmental air circulation rate, clothing, RF power density, and duration of exposure
(time). Temperature regulation in the human body is accomplished primarily through the action
of sweat glands (cooling through evaporation) and by heat exchange resulting from peripheral
circulation of blood.
If RF exposure is not prolonged and within the time exposure limits specified in
DODINST 6055.11, the internal core temperature of the body will remain normal. Where areas
of the body are cooled by an adequate flow of blood through the vascular system, there is less
likelihood of tissue damage resulting from abnormal temperatures.
C-4.
NONTHERMAL EFFECTS
References are sometimes made to nonthermal biological effects of EMR. This means
that the observed effect was not related to the biological heating of tissues.
The guidelines and limits stipulated in DODINST 6055.11 are based on short-term
thermal effects. The various technical and health experts who contributed towards the
development of these guidelines and limits have concluded that no reliable scientific data exist
that support nonthermal (other than shock) EMR effects. In addition, no verified reports exist of
injury or adverse effects on the health of humans who have been exposed to electromagnetic
fields within the limits of frequency and SAR specified in DODINST 6055.11.
C-5.
TIME-AVERAGED EXPOSURE
For controlled environments, personnel exposure levels higher than those shown in table
C-1 are permitted if the average exposure, over a 6-minute time interval, does not exceed PEL.
This is true for frequencies from 0.003 MHz to 15 GHz (15000 MHz). For frequencies above 15
GHz, the averaging time interval is frequency dependent. Similarly, in uncontrolled
environments, averaging time varies by frequency, as shown in table C-3.
C-8

The following example, representative of a common workplace safety concern, is
provided to help understand the concept of time-averaged RF exposure limits, as well as the
method by which such limits are calculated.
A worker wishes to conduct maintenance in an area close to a transmitting antenna. The
radiated power density in the desired work area has been surveyed (measured) and found to
exceed PEL by a factor of two. The transmitter cannot be silenced, nor can the transmitted
power be reduced. Given the following conditions, determine if maintenance personnel can
safely enter the area and, if so, for how long.
TX Frequency is 200 MHz
TX Power Density (TXPD) is 2 mW/cm2
PEL at 200 MHz is 1 mW/cm2
Time Average Interval (TAI) is 6 Min
Calculated Time Averaging Factor (TAF) = PEL/TXPD
TAF = (1 mW/cm2)/(2 mW/cm2) = 0.5
Calculated new Time Average Interval (TAI)
TAI = TAF*TAF or (6)*(0.5), which equals 3 Min
Based upon the above calculation, workers are permitted to conduct maintenance
operations in the RF hazard area for 3 minutes, after which they must leave the area for a
minimum of 3 additional minutes before returning.
C-9/(C-10 Blank)

APPENDIX D
CALCULATIONS AND MEASUREMENTS OF ELECTROMAGNETIC FIELDS
SECTION I. CALCULATIONS OF POWER DENSITY IN ELECTROMAGNETIC FIELDS
D-1.
INTRODUCTION
D-1.1 Section I discusses the electromagnetic environment and calculations of power density
in an electromagnetic field. This is followed by an introduction to calculation aids, and various
tables and examples that can be used in the prediction of radio-frequency (RF) radiation
hazards.
D-1.2 Electromagnetic radiation (EMR) is the emission of energy from a source in the form of
an electromagnetic wave. EMR is not visible nor is it detected reliably by any biological
response. EMR intensity must be measured by instruments or approximated by calculation.
This section provides procedures and tabular material which aid in calculating the power
density radiated from large-aperture antennas.
D-1.3 These computations enable the supervisor or any other designated personnel to derive
power density as power flow per unit area expressed in milliwatts per square centimeter (mW/
cm2). From these calculations, safe distances can be determined to reduce the possibilities of
personnel exposure to excessive EMR or accidental ignition of ordnance materials or fuels.
D-1.4 Calculations may be conducted in either the metric or English system of units as long
as consistency is maintained. Both centimeters (cm) and meters are commonly used to
calculate power density in mW/cm2 or watts per square meter (W/m2). The correction factor
graphs are presented with distance in wavelengths, which gives a dimensionless number that
can be used with all units. Units shown in examples are selected as typical applications.
D-2.
THE ELECTROMAGNETIC ENVIRONMENT
D-2.1 The spatial regions of radiation associated with any arbitrary antenna are known as the
near-field region (which generally contains two subregions: the static near-field region and
induction, or radiating, near-field region) and the far-field region (or radiation region). For
aperture antennas, the near-field and far-field regions are also known as the Fresnel and
Fraunhofer regions, respectively, because the Scalar Diffraction Theory is used to determine
the fields generated from these antennas. There is also a third region of radiation, the
intermediate region, which is a region of transition between the near- and far-field regions. The
fields in the intermediate region are generally complex and are, therefore, difficult to determine.
However, the spatial extent of the intermediate radiation region is generally small compared to
the extent of the near- and far-field regions; therefore, the intermediate region is generally
ignored in determining electromagnetic field quantities, or it is included as part of the near field.
D-1

The far-fi\eld region of an antenna is traditionally defined as the region around an antenna
where the phase front of a spherical electromagnetic wave over a planar aperture does not
exceed 8 radians (22.5). The far-field region begins at a distance from the antenna given
by the Friis Free-Space Transmission Formula:
2
2L
r --------
where is the wavelength of the radiation. For wire, monopole, and dipole antennas, L is
taken as the electrical length of the antenna (e.g., for a monopole or a half-wavelength dipole
antenna, L = 2 ). For an aperture antenna, L is generally taken as the largest linear
dimension of the aperture.
In the far-field region of the antenna, the magnitudes of the electric and magnetic fields vary
inversely with the distance from the antenna ( E , H 1 r ). Furthermore, the ratio of the electric
field magnitude to the magnetic field magnitude ( E H ), also called the wave impedance, has a
constant value of 377 ohms ( ) .
Because of the inverse relation between the electric/magnetic field magnitudes and the
distance from the antenna, the power radiated from the antenna can be envisioned as being
distributed over a spherical shell at that distance such that:
GP
S = -----------2
4r
where:
S = power density of the radiation (in W/m2 or mW/cm2),
P = total power transmitted from the antenna [in watts (W) or milliwatts (mW)],
G = far-field gain (power ratio) of the antenna, and
r = distance from the antenna (meters or cm).
The gain, G, is generally known for an antenna since the parameter is specified in the
documentation provided by the antenna manufacturer or calibration lab. However, if the gain of
an antenna is not known, it can be calculated to an acceptable degree of accuracy by the
following, provided the antenna azimuth and elevation beamwidths are known or measured:
4
G ------------- az el
where:
az = azimuth angle beamwidth, in radians,
el = elevation angle beamwidth, in radians, and
180
1 radian = ----------- .
D-2

From the gain and radiation wavelength, another useful quantity, the effective area of the
antenna (the area of the antenna beam-forming surface), Ae, can be calculated:
2
G
A e = ---------- .
4
In the real world, measurements of radiation from an emitting antenna source are conducted
using another antenna with its own characteristics. If Aer and Gr are the effective area and gain
of the measurement antenna, respectively, then we expect the total power Pr received by the
measurement antenna to be:
2
P r = SAer
Gt Pt Gr
= -----------2 ------------
4r 4
or
2
Gt Gr Pt
P r = ----------------------2
( 4r )
where:
Gt = gain of the transmitting antenna, and
Pt = total power transmitted from transmitting antenna.
Therefore, alternatively:
P
4P
S = -------r = -----------2-r .
Aer
G
r
Again, S can be expressed in mW/cm2 or W/m2.

With the power density S known, it becomes a relatively simple matter (in the far field) to
determine the magnitudes of the electric and magnetic fields. The power density, electric field,
and magnetic field are related by:
S = EH sin ,
where:
= angle between the electric and magnetic field amplitude directions.
Since, in the far field, EMR propagates as a transverse wave (=90 or /2 radians), and
since the magnetic and electric fields are related to each other by the wave impedance, we
have:
D-3

2
E
2
S = ------ W m
Z
or
2
S = ZH W m
where:
E = electric field intensity in volts per meter,
H = magnetic field intensity in amperes per meter, and
Z = wave impedance = 377.
Note that 1 W/m2 = 0.1 mW/cm2.
D-2.2 In the near-field region of an antenna (also known as the Fresnel region for aperture
antennas), determination of electromagnetic field characteristics is more complicated. The
electric and magnetic fields are generally dependent on the source of the radiation and can vary
with both angular position and distance around an antenna. Furthermore, the wave impedance
of the radiation is no longer a constant value, as it was in the far-field (Fraunhofer) region. In
general, a source antenna that has a high terminal voltage, high impedance, and low driver
current will generate a high electric field in the near field which varies as 1/r3 (r being, once
again, the distance between the antenna and measurement point), while the magnetic field
varies as 1/r2; the wave impedance of such an antenna will be much greater than 377, on the
order of thousands of ohms. However, a source antenna that has low terminal voltage, low
impedance, and high driver current will generate a higher magnetic field in the near-field region
which varies as 1/r3, while the electric field varies as 1/r2. The wave impedance of an antenna
where the magnetic field is the dominant radiation component will typically be one to two orders
of magnitude below the far-field wave impedance. Note that, as the distance from an antenna is
increased, the variation of the electric and magnetic fields with distance will approach the
characteristic 1/r dependence associated with the far-field region. Furthermore, as distance
from the antenna is increased, the wave impedance will asymptotically approach the constant
value of 377.
Because the antenna gain and beamwidth are degraded in the near-field region, the
power density will be modified such that:
GP
S = -----------2 N
4r
where N is the near-field correction factor, and G, P, and r are as previously defined.
Again, since we are making measurements in the real world, the possibility exists that
fields from a radiating source could be measured in the near-field region of the receiving
antenna used for the measurements. Therefore, a correction factor for the measurement
antenna may have to be used such that:
D-4

2
P r = SAer
Gt Gr Pt
- N t Nr
= ----------------------2
( 4r )
or
Pr
4P r
S = ------- = -----------------2Aer
Nr Gr
where:
Nt = near-field correction factor for the source antenna, and
Nr = near-field correction factor for the measurement antenna.
The other parameters in the above equations are as previously defined.
The near-field correction factor, N, is dependent on several parameters, namely:
a. Mismatch (Voltage Standing Wave Ratio) loss derived from the reflection at the antenna
feed port because of impedance mismatch.
b. RF losses between the antenna and the antenna feed point or measurement point.
c. Spillover loss, which takes into account energy spillover beyond the edge of a reflector
antenna into the backlobes of the antenna.
d. Illumination efficiency, which is the ratio of the directivity of an antenna to the directivity of
a uniformly illuminated antenna of the same aperture size.
e. Phase error loss, or loss resulting from the fact that the antenna aperture is not a uniform
phase surface.
Parameters a. and b. above are generally applicable to all antennas and are usually
determined by measurement. Parameter c. is applicable to reflector antennas and is also
usually determined by measurement. Parameters d. and e. are generally applicable to aperture
antennas and can be calculated, to a reasonable approximation, using the methods outlined in
the following paragraphs.
D-2.3 For aperture antennas, the near-field correction factor depends on the type of antenna
illumination and the distance from the antenna. If the antenna illumination is unknown, it can be
estimated by the following formulas.
D-2.4 After calculating R, as shown in figure D-1, the illumination can be estimated from
tables D-1 and D-2. This estimate is then checked by calculating the antenna efficiency.
Illuminations above cos4 or (1-r2)4 are purposely omitted since the gain reduction in the Fresnel
region would be almost negligible.
D-5

R = 5.84 10 5 ( f ) ( BW ) (L or D in meters),
R = 5.84 10 7 ( f ) ( BW ) (L or D in cm), or
R = 1.78 10 7 ( f ) ( BW ) (L or D in feet),
where:
R = constant for estimating illumination,
= frequency in megahertz (MHz),
BW = beamwidth in degrees (horizontal or vertical) at 3 dB points,
L = horizontal or vertical dimension of a rectangular aperture antenna, and
D = diameter of a circular aperture antenna.
Figure D-1. Calculation of Antenna Illumination Constant
Table D-1. Rectangular Apertures
0.88 to 1.20
1.20 to 1.45
ESTIMATED
ILLUMINATION
uniform
cos
1.45 to 1.66
cos2
0.667
1.66 to 1.93
cos3
0.575
1.93 to 2.03
cos4
0.515
LIMITS OF R
Fh or Fv
1.000
0.810
NOTE:
F = F h Fv
Table D-2. Circular Apertures with (1-r2) Illumination
1.02 to 1.27
ESTIMATED
ILLUMINATION
uniform
1.00
1.27 to 1.47
(1-r2) Taper
0.75
1.47 to 1.65
(1-r2)2 Taper
0.56
1.65 to 1.81
(1-r2)3
Taper
0.44
>1.81
(1-r2)4
Taper
0.36
LIMITS OF R
D-2.5 When the constant (R) is found to be borderline between two orders of illumination, the
higher order should be checked for antenna efficiency first, because the power density in the
D-6

Fresnel region will be greater and, therefore, more hazardous to personnel. If the choice of the
higher illumination causes the efficiency to be too high, then the next lower order can be tried.
The antenna efficiency can be checked by the equation:
2
G()
K = ------------------4 ( A )F
where:
K = antenna efficiency,
A = antenna aperture area (same units as ), and
F = factor depending on antenna illumination.
The numerical factor (F) is tabulated in tables D-1 and D-2 adjacent to the type of antenna
illumination. An efficiency (K) within the limits of 0.0017 to 1.0 is reasonable.
D-3. CALCULATION OF THE ON-AXIS POWER DENSITY FROM LARGE-APERTURE
ANTENNAS IN THE FRESNEL REGION
D-3.1 RECTANGULAR ANTENNAS. After the illumination has been determined, the Fresnel
gain correction factors for both the horizontal and vertical planes can be found using the
appropriate aperture dimension. Graphic curves of gain versus distance have been provided
for finding the gain correction factors within the Fresnel region of antennas, depending on the
type of illumination of the antenna. Graphs showing uniform, cos, cos2, cos3, and cos4
illumination are given by figures D-2 through D-6. On each of these graphs, the abscissa is the
distance from the antenna in wavelengths, and the ordinate is the gain reduction in decibels
(dB) within the Fresnel region. The aperture dimension, L, on the graphs is in wavelengths.
The Fresnel gain is always less than the far-field gain and is determined by subtracting the
appropriate gain reduction for both horizontal and vertical planes from the far-field gain.
Therefore, by the use of this reduced gain in the far-field equation, the power density in the
Fresnel region can be calculated.
D-3.2 CIRCULAR ANTENNAS. After the illumination has been determined, the Fresnel
region power density can be determined by calculating the far-field distance (d=2D2/ meters),
calculating the power density at this point by the Friis Free-Space Transmission Formula:
PG
PD = ----------------24 ( d )
and by multiplying this power density by the gain correction factor given in figure D-7 for the
desired distance (d) and antenna illumination.
D-7
D-8
Figure D-2. Fresnel Region Gain Correction for Uniform Illumination (Rectangular Aperture)

D-9
Figure D-3. Fresnel Region Gain Correction for Cosine Illumination (Rectangular Aperture)
D-10
Figure D-4. Fresnel Region Gain Correction for Cosine Square Illumination (Rectangular Aperture)

D-11
Figure D-5. Fresnel Region Gain Correction for Cosine Cubed Illumination (Rectangular Aperture)
D-12
Figure D-6. Fresnel Region Gain Correction for Cosine Fourth Illumination (Rectangular Aperture)

Figure D-7. Normalized On-Axis Power Density Curves

Circular Aperture (1-r2)
D-13

D-4.
CALCULATION OF POWER DENSITY OF SIDELOBES
Under certain circumstances, it may be necessary to calculate the power density at a

location to the side of a radar antenna main beam. If the antenna in question does not have its
aperture distribution defined in its fundamental characteristics, the aperture distribution
parameters can be established by using tables D-3 and D-4. Table D-3 defines the directivity
patterns for circular aperture from (1-r2)0 through (1-r2)2 illumination, while table D-4 defines the
directivity patterns of rectangular aperture from uniform through cos2 illumination. Because the
sidelobe is less than the main beam, the power density is given as:
PG
PD = ----------------2- ( SL ) ,
4 ( d )
where:
SL = gain degradation of the first sidelobes.
The angular displacement in degrees of the first sidelobes is also listed in tables D-3 and D-4.
Table D-3. Circular Aperture Distribution
HALF-POWER
BEAMWIDTH
IN DEGREES
ANGULAR
DISPLACEMENT
TO FIRST ZERO
IN DEGREES
INTENSITY
OF FIRST
SIDELOBE
DB BELOW
MAXIMUM
ANGULAR
DISPLACEMENT
TO FIRST
SIDELOBE
IN DEGREES
2 0
58.9 ---D
69.8 ---D
17.6
97.4 ---D
2 1
72.7 ---D
93.6 ---D
24.6
119.8 ---D
2 2
84.3 ---D
116.2 ---D
30.6
139.3 ---D
TYPE OF
ILLUMINATION
(1 r )
(1 r )
(1 r )
NOTE: D = Aperture diameter in the same units as .
Table D-4. Rectangular Aperture Distribution

HALF-POWER
BEAMWIDTH
IN DEGREES
ANGULAR
DISPLACEMENT
TO FIRST ZERO
IN DEGREES
INTENSITY
OF FIRST
SIDELOBE
DB BELOW
MAXIMUM
ANGULAR
DISPLACEMENT
TO FIRST
SIDELOBE
IN DEGREES
Uniform
50.8 --L
57.3 --L
13.2
83.8 --L
Cosine
68.8 --L
85.9 --L
23
113.5 --L
Cosine Squared
83.2 --L
114.6 --L
32
137.3 --L
TYPE OF
ILLUMINATION
NOTE: L = Vertical or horizontal length of aperture in the same units as .
D-14

D-5.
SAMPLE ON-AXIS POWER DENSITY COMPUTATION
D-5.1 For rectangular aperture antennas, the preceding procedures are illustrated by the
calculation of near-field power density of an imaginary AN/SPS-00 radar as shown in figure D-8.
For circular aperture antennas, the calculation of near-field power density is illustrated in figure
D-9 for a hypothetical antenna with a circular aperture.
D-5.2 For rectangular aperture antennas, the near-field gain correction factor (N) is the sum
of the vertical and horizontal gain correction factors in dB. These factors are derived from the
graphs in figures D-2 through D-6, which show the near-field gain correction in dB as a function
of the antenna dimension (either vertical or horizontal) in wavelengths and the distance (d) from
the antenna in wavelengths. For circular aperture antennas, the near-field numerical gain
correction factors are derived from the graph in figure D-7.
D-6.
DETERMINING THE HAZARD FROM A ROTATING BEAM
D-6.1 Although the on-axis power density of a radar beam may exceed the PELs specified in
tables C-1 and C-3, there may be no hazard if the beam is being rotated or scanned. Duration
of exposure, as well as power density, is a factor in determining the RF hazard. The time factor
is recognized by specifying the PEL in two ways: for example, 10 mW/cm2 for continuous
exposure, and 1 mW-hr/cm2 in any given 0.1-hour interval. Since a continuous 10 mW/cm2 for
0.1 hour produces energy of 1 mW-hr/cm2, these limits are identical for the case of continuous
exposure. The latter limit, though, expresses the fact that higher power densities up to 100
mW/cm2 are permissible for intermittent exposure. To illustrate the use of this criterion for a
rotating antenna, assume the following radiation characteristics:
Maximum power density on axis
50 mW/cm2
Beamwidth
10 degrees
Rotation speed
6 rpm
D-15

1. The assumed characteristics of the AN/SPS-00 antennas are as follows:
a. Antenna width = 0.991 meters (3.25 ft) = 29
b. Antenna height = 0.177 meters (0.58 ft) = 5.2
c. Gain (far-field) = 29.3 dB = 851 gain ratio
d. Center frequency = 8825 MHz
e. Beamwidth = 3.0 horizontal and 13 vertical
f. Power = 13.1 W (average power at 0.5 sec pulse width)
300
g. = ------------ = 0.034 meter (0.11 ft)
8825
2
2L
h. Far field --------- where L is the longest linear dimension of antenna (meters)
2 ( 0.991 ) ----------------------= 57.8 meters.

0.034
i.
R, the constant for estimating illumination, is found by:

5
R = 5.84 10 ( f ) ( BW ) (L in meters)
Where:
= frequency in MHz,
BW = beamwidth in degrees (horizontal or vertical) at 3 dB points, and
L = horizontal or vertical dimension in meters (feet).
For horizontal illumination:
5
R = 5.84 10 ( 8825 ) ( 3.0 ) ( 0.991 )

R = 1.53 - estimated illumination is cos2 (from table D-1).
For vertical illumination:
5
R = 5.84 10 ( 8825 ) ( 13 ) ( 0.177 )

R = 1.19 - estimated illumination is uniform (from table D-1).
Figure D-8. Sample On-Axis Power Density Computation for a Rectangular
Aperture Antenna (Sheet 1)
D-16

2. Antenna efficiency (K) is checked by using values from table D-1 of:
Fh = 0.667 and F v = 1.0
F = F h F v = 0.667
2
G( )
851 ( 0.034 )
K = ------------------- = -------------------------------------------------------------------------4 ( A )F
4 ( 3.14 ) ( 0.991 ) ( 0.177 ) ( 0.667 )
K = 0.67 verifying estimated illuminations.
3. N is the sum of the horizontal and vertical correction factors obtained from figure D-4 for cos2
and figure D-2 for uniform illumination. At 1 meter (3.28 ft) or 29, the horizontal gain reduction
is approximately 9.0 dB; the vertical gain reduction at 1 meter is 0.1 dB.
Therefore,
N ( dB ) = ( 9.0dB ) + ( 0.1dB )
= 9.1dB.
1
N ( ratio ) = antilog ( 0.91 ) = ------- .
8.1
PD at 1 meter
PG
= ----------------2- ( N )
4 ( d )
13.1 ( 851 ) 1
= -----------------------2- ------8.1
12.56 ( 1 )
= 109 W m
= 109 W m
2
2
= 109 mW cm .
Figure D-8. Sample On-Axis Power Density Computation for a Rectangular

Aperture Antenna (Sheet 2)
D-17

1. The assumed characteristics of a hypothetical circular aperture antenna are as follows:

a. Aperture diameter (D) = 2 meters
b. Gain (far-field) (G) = 21 dB = 126 (numerical gain)
c. Center frequency () = 5000 MHz
d. Beamwidth = 3
e. Power (P) = 50 W (average)
300
f. Wavelength () = --------- = 0.06 meters
f
2
2D
g. Far-field distance = ---------- = 133.33 meters
h. Antenna illumination constant (R) = 5.84 10 ( f ) ( beamwidth ) ( D )

5
= 5.84 10 ( 5000 ) ( 3 ) ( 2 )
= 1.752 .
i. Using table D-2, the value of R, 1.752, indicates a circular aperture antenna with an
estimated (1-r2)3 taper illumination. The corresponding antenna illumination factor (F), also
from table D-2, is equal to 0.44.
2
G
2. Antenna efficiency (K) = -------------4AF
2
126 ( 0.06 )
= -------------------------------------------2
4 ( D 4 ) ( 0.44 )
126 ( 0.0036 )= ------------------------------2
2
( 2 ) ( 0.44 )
= 0.026 .
Figure D-9. Sample On-Axis Power Density Computation for a

Circular Aperture Antenna (Sheet 1)
D-18

3. N is the circular aperture gain correction obtained from figure D-7. Since our hypothetical
antenna was found to have a (1-r2)3 taper illumination, the curve specified for =3 would be
applicable. Therefore, the power density at a point 5 meters away from the antenna would
be as follows:
a. With d=5m, the normalized distance (with respect to the far-field distance) X is
calculated as:
2
2D
5
X = d ---------- = ------------- = 0.0375 .
133.3
b. From figure D-7, N is found to have a value of 100 for the =3 curve at X=0.0375.
c. Therefore, at a distance of 5 meters, the power density is given by:
PD = N (PD at far - field distance)
GP
= N ------------------------------22
4 ( 2D )
( 100 ) ( 126 ) ( 50 )= -------------------------------------2
4 ( 133.3 )
= 2.82 W m
or 0.282 mW cm .
Figure D-9. Sample On-Axis Power Density Computation for a

Circular Aperture Antenna (Sheet 2)
D-6.2 If this antenna was not rotating while transmitting, the permissible exposure time in a
continuous power density of 50 mW/cm2 is:
1
- = 0.02 hour
T ( hr ) = -----------------------------------2
PD ( mW cm )
and about 1 minute out of each 6 minutes would be permitted in the beam.
D-6.3 When the antenna is rotating at 6 rpm, it will make one revolution each 10 seconds
(0.167 minute), and a point will be exposed to the beam 10/360ths (beamwidth over 360) of this
period. The actual exposure time for each revolution is 0.278 second or 0.0046 minute. In 0.1
hour, there will be 36 revolutions (6 rev/min x 6 min), so that in this 6 minutes, the total exposure
time is 0.167 minute. The total energy/cm2 is thus (50 mW/cm2)(0.167 min) (1 hr/60 min) or
0.139 mW-hr/cm2. This is below the permissible intermittent exposure level of 1.0 mW-hr/cm2;
D-19

thus, the radar is not hazardous as long as it is rotating, even though the on-axis power density
exceeds the safe limit for continuous exposure.
D-7.
DETERMINING THE HAZARD FROM A SCANNING BEAM
Power density from a scanning antenna can be approximated by a method similar to that
for the rotating antenna. As a rule of thumb, the fixed-beam power density of a scanning
antenna can be reduced by a factor of twice the beamwidth divided by the scan angle. That is:
2 BW
PD ( S ) = ------------------ PD ( F )
SA
where:
PD(S)
PD(F)
BW
SA
D-8.
= power density while scanning,

= fixed power density,
= beamwidth in degrees, and
= scan angle in degrees.
INTRODUCTION TO CALCULATION AIDS
The data in this paragraph includes tables and graphs which will be of assistance in the
calculation of RF radiation hazards. Explanations regarding the use of the various tables are
presented prior to the tables when such explanations are deemed necessary.
D-8.1 The relation between the frequency and wavelength of EMR is a relatively simple one.
For radiation propagating at a frequency and wavelength , we have the following relation:
V = f
where:
V = the velocity of the electromagnetic wave.
Since an electromagnetic waves velocity is constant in free space (V = speed of light in
vacuum 3x108 m/s), the wavelength can be calculated for any given frequency as:
= 300 f meters or
= 30000 f cm
where:
= frequency in MHz.
D-20

D-8.2 TRIGONOMETRIC FUNCTIONS OF A RIGHT TRIANGLE. In the right triangle shown
in figure D-10, the trigonometric functions of angle A are defined as follows:
sin A = a c ,
cos A = b c , and
tan A = a b .
The following relations derived from figure D-10 may also be useful when solving
problems:
2
c = a + b (Pythagorean Theorem),
sin2 A +
sec A =
csc A =
cot A =
cos 2 A = 1 ,
1 ( cos A ) = c b (Secant Function),
1 sin A = c a (Cosecant Function),
1 tan A = b a Cotangent Function),
cos 2 A = cos 2 A sin 2 A , and

sin 2 A = 2 sin A cos A .
Figure D-10. Functions of a Right Triangle

D-8.3 USE OF TRIGONOMETRIC FUNCTIONS IN SOLVING PROBLEMS. Refer to
figure D-11, which illustrates the use of trigonometric functions in solving problems.
D-21

Given:
As shown above, a radar set in which the antenna has a radiation pattern that
covers a vertical angle of 60, with the beam center elevated +20 from the
horizontal plane. The center of the antenna is 2 meters above the base of a
pedestal, which is mounted on a 5-meter tower.
To find:
Whether any part of the main beam will illuminate a person who is 1.8 meters tall
and who is on the ground at a distance of 30 meters.
Solution: Lower edge of beam = +20-(1/2 x 60)

= -10
a
tan 10 = --b
a = b tan 10 = 30 0.1763 = 5.3 meters
The center of the antenna above ground (tower + pedestal) is 7 meters (5 meters +
2 meters), and the clearance of the beam above ground at 30 meters is 7 meters 5.3 meters, or 1.7 meters. Therefore, a 1.8-meter person would have 1.8 meters 1.7 meters, or 0.1 meter, of his body illuminated by the radar beam.
Figure D-11. Sample Use of Trigonometric Functions for Solving Problems
D-22

D-8.4
THE DECIBEL.
D-8.4.1 The decibel is part of a larger unit called a bel. As originally used, the bel
represented a power ratio of 10 to 1 between the strength of two sounds. To gain a better
understanding of the bel, consider three sounds of unequal power intensity. If the power
intensity of the second sound is 10 times the power intensity of the first, its power level is said to
be 1 bel above that of the first. If the third sound has a power intensity which is 10 times that of
the second, its level is 1 bel above that of the second. But, since the third sound is 100 times as
intense as the first, its level is 2 bels above that of the first. Thus, a power ratio of 100 to 1 is
represented by 2 bels; a power ratio of 1000 to 1, by 3 bels; a power ratio of 10,000 to 1, by 4
bels; etc. It is readily seen, therefore, that the concept of bels represents a logarithmic
relationship, since the base 10 logarithm of 100 equals 2 (corresponding to 2 bels), the
logarithm of 1000 equals 3 (corresponding to 3 bels), etc. The exact relationship is given by the
formula:
P
Bels = log -----2P1
P2
where ------ represents the power ratio.
P1
D-8.4.2 This logarithmic characteristic of the bel makes it a very convenient means for
expressing power ratios. Since the bel is a rather large unit, however, its use may prove
inconvenient. Usually, therefore, a smaller unit, the dB, is used. Ten dB equals 1 bel. A 10-to-1
power ratio, which is represented by 1 bel, is also represented by 10 dB; a 100-to-1 ratio (2
bels) is represented by 20 dB; a 1000-to-1 ratio (3 bels) is represented by 30 dB, etc. The
formula for bels may be rewritten to give a result in dB merely by multiplying by 10. Thus, the
formula becomes:
P
dB = 10 log -----2- .
P1
For example, assume that it is necessary to find the attenuation ratio of an RF attenuator which
is to be used to measure transmitter power output. On test, it is found that 60,000 W of RF
input to the attenuator produces an output of 6 mW. To find the attenuation ratio, use the
equation:
P2
Attenuation ratio = -----P1
60, 000
= -----------------0.006
= 10, 000, 000.
This ratio can be expressed much more conveniently in terms of dB.
D-23

P
dB = 10 log -----2P1
, 000= 10 log 60
----------------0.006
= 10 log 10, 000, 000
= 70 dB .
In this case, the attenuation ratio is 70 dB. In other words, P 2 is said to be 70 dB up with
respect to P 1 . In all instances where P 2 is numerically greater than P 1 , as in the above
example, the final result is expressed as a positive quantity. When P 2 is smaller than P1 , the
numerical result is the same, but it is expressed as a negative quantity in dB. If, for example,
P 2 is .006 W and P 1 is 60,000 W, then:
P
dB = 10 log -----2P1
0.006 = 10 log ----------------60, 000
= 10 log 0.0000001
= 70.
In this case, P 2 is said to be 70 dB down with respect to P 1 .
D-8.4.3 Voltage and current ratios may also be expressed in terms of dB, provided that the
resistance (or impedance) remains constant. For equal resistances, the formulas are:
E
dB = 20 log -----2- and
E1
I
dB = 20 log ---2- .
I1
The difference in the multiplying factor in these formulas (20 rather than 10, as in the case of
power ratios) arises from the fact that power is proportional to voltage or current squared, and
when a number is squared, the logarithm of that number is doubled. For power ratios, the dB
value is 10 times the logarithm of the ratio. For voltage or current ratios, the dB value is 20
times the logarithm of the ratio.
D-8.4.4 Conversions from voltage, current, or power ratios to dB may be readily made by
referring to table D-5. Conversions may also be made by means of the graph shown in
figure D-12.
D-24

Table D-5. Decibel Table: Voltage, Current, and Power Ratios

MINUS
VOLTAGE OR
CURRENT RATIO
(EQUAL IMPEDANCE)
1.00000
0.98900
0.97700
0.96600
0.95500
0.94400
0.93300
0.92300
0.91200
0.90200
0.89100
0.84100
0.79400
0.75000
0.70800
0.66800
0.63100
0.59600
0.56200
0.53100
0.50100
0.47300
0.44700
0.42200
0.39800
0.37600
0.35500
0.33500
0.31600
0.28200
0.25100
0.22400
0.20000
0.17800
0.15900
0.14100
0.12600
0.11200
0.10000
0.03160
0.01000
0.00316
dB
POWER
RATIO
1.00000
0.97700
0.95500
0.93300
0.91200
0.89100
0.87100
0.85100
0.83200
0.81300
0.79400
0.70800
0.63100
0.56200
0.50100
0.44700
0.39800
0.35500
0.31600
0.28200
0.25100
0.22400
0.20000
0.17800
0.15900
0.14100
0.12600
0.11200
0.10000
0.07940
0.06310
0.05010
0.03980
0.03160
0.02510
0.02000
0.01590
0.01260
0.01000
0.00100
0.00010
0.00001
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10.0
11.0
12.0
13.0
14.0
15.0
16.0
17.0
18.0
19.0
20.0
30.0
40.0
50.0
PLUS
VOLTAGE OR
CURRENT RATIO
(EQUAL IMPEDANCE)
1.000
1.012
1.023
1.035
1.047
1.059
1.072
1.084
1.096
1.109
1.122
1.189
1.259
1.334
1.413
1.496
1.585
1.679
1.778
1.884
1.995
2.113
2.239
2.371
2.512
2.661
2.818
2.985
3.162
3.550
3.980
4.470
5.010
5.620
6.310
7.080
7.940
8.910
10.000
31.600
100.000
316.000
POWER
RATIO
1.000
1.023
1.047
1.072
1.096
1.122
1.148
1.175
1.202
1.230
1.259
1.413
1.585
1.778
1.995
2.239
2.512
2.818
3.162
3.548
3.981
4.467
5.012
5.623
6.310
7.079
7.943
8.913
10.000
12.600
15.900
20.000
25.100
31.600
39.800
50.100
63.100
79.400
100.000
1000.000
10000.000
100000.000
D-25

Figure D-12. Power Gain Ratio Versus Decibel Gain

D-26

D-8.5
THE DBM.
D-8.5.1 It should be clearly understood that the term decibel does not, in itself, indicate
power, but rather a ratio of, or comparison between, two power values. It is very often
desirable, however, to express a single level or quantity of power, voltage, or current in dB, as,
for example, in transmission line work or in connection with the input or output of an amplifier.
This can be done by using a fixed power level as a reference. The original standard reference
level was 6 mW (0.006 W), but to simplify calculations, a 1-mW standard (dBm) has been
adopted and will be used hereafter as the reference level. [Some manufacturers use 1 W
(dBW) as a standard.]
D-8.5.2 When 1 mW is used as a reference level, the ratio is expressed in dBms. The
abbreviation dBm indicates dB relative to a 1-mW standard. Thus, a pulsed radar transmitter
having an average power output of 100 W is said to have an average power output of 50 dBm.
The conversion from power to dBm can be made as follows:
P
Average power ( dBm ) = 10 log -----2P1
(where P 1 is the reference value of 0.001 W),
100 Average power ( dBm ) = 10 log -----------0.001
= 10 log 100,000
= 50 dBm .
D-8.5.3 Conversions from power to dBm can be made more readily by means of the graph
shown in figure D-13. Reasonable care should be exercised in reading the graph, using the
appropriate dBm scale for power in milliwatts, watts, kilowatts, or megawatts.
D-8.6 CONVERSION OF POWER OR DBM TO MICROVOLTS ACROSS 50, 72, OR
600 OHMS.
D-8.6.1 Both the dB and the dBm are power ratios; their adaptation to voltage or current ratios
is meaningful only if the impedance is the same for both values of voltage (or current) in the
ratio. For example, the formula for the ratio, expressed in dB, of two voltages, E2 and E1, is as
follows:
E
dB = 20 log -----2- .
E1
D-27

D-8.6.2 To calculate the voltage gain of an amplifier when the input impedance differs from
the output, use the following formula:
E2
Z
dB = 20 log ------ + 10 log -----1
E1
Z2
where:
E1 = input voltage,
E2 = output voltage,
Z1 = input impedance, and
Z2 = output impedance.
D-8.6.3 In calculations involving power in transmission lines, it is often necessary to convert
extremely small amounts of power to dBm or to convert either of these values to voltage, in
microvolts, which would appear across a load impedance of 50, 72, or 600 ohms. Conversions
from dBm or power in picowatts to microvolts across 50, 72, or 600 ohms, or vice versa, may be
made directly by means of table D-6.
D-28

Figure D-13. Power Gain Ratio Versus dBm
D-29

Table D-6. dBm Conversion Table

dBm
0
-3
-6
-9
-12
-15
-18
-21
-24
-27
-30
-33
-36
-39
-42
-45
-48
-51
-54
-57
-60
-63
-66
-69
-72
-75
-78
-81
-84
-87
-90
-93
-96
-99
-102
-105
-107
D-30
MICROVOLTS
ACROSS
50 OHMS
223,607.000
158,314.000
112,094.000
79,358.000
56,192.000
39,780.000
28,174.000
19,932.000
14,112.000
9,990.000
7,073.000
5,009.000
3,546.000
2,511.000
1,776.000
1,258.000
890.000
630.000
446.000
316.000
223.607
158.314
112.094
79.358
56.192
39.780
28.174
19.932
14.112
9.990
7.073
5.009
3.546
2.511
1.776
1.257
0.999
MICROVOLTS
ACROSS
72 OHMS
268,328.000
189,976.000
134,513.000
95,230.000
67,431.000
47,736.000
33,809.000
23,919.000
16,934.000
11,988.000
8,487.000
6,011.000
4,256.000
3,013.000
2,132.000
1,509.000
1,068.000
756.000
536.000
379.000
268.328
189.976
134.513
95.230
67.431
47.736
33.809
23.919
16.934
11.988
8.487
6.011
4.256
3.013
2.132
1.509
1.199
MICROVOLTS
ACROSS
600 OHMS
774,596.700
548,379.400
388,265.400
274,845.400
194,576.500
137,738.900
97,519.200
69,034.800
48,873.300
34,597.700
24,494.900
17,341.300
12,276.800
8,691.400
6,153.000
4,355.700
3,083.800
2,183.100
1,545.500
1,094.000
774.597
548.379
388.265
274.845
194.576
137.739
97.519
69.035
48.873
34.598
24.495
17.341
12.277
8.691
6.153
4.356
3.460
PICOWATTS
1,000,000,000.00000
501,200,000.00000
251,250,000.00000
125,900,000.00000
63,100,000.00000
31,620,000.00000
15,850,000.00000
7,943,000.00000
3,981,000.00000
1,995,000.00000
1,000,000.00000
501,200.00000
251,200.00000
125,900.00000
63,100.00000
31,620.00000
15,850.00000
7,943.00000
3,981.00000
1,995.00000
1,000.00000
501.20000
251.25000
125.90000
63.10000
31.62000
15.85000
7.94300
3.98100
1.99500
1.00000
0.50120
0.25120
0.12590
0.06310
0.03162
0.01995

SECTION II. MEASUREMENTS OF ELECTROMAGNETIC FIELDS
D-9.
INTRODUCTION
This section provides guidance in the selection of test equipment and procedures for
performing power measurements of RF energy.
D-10. INSTRUMENTATION FOR POWER MEASUREMENTS
Instruments for field measurements of RF power density are generally either a
broadband radiation hazard meter or an RF power meter with a calibrated antenna.
D-10.1 RADIATION HAZARD METERS. Radiation hazard meters are made specifically to
detect and measure potentially hazardous electromagnetic energy radiating or leaking from RF
or microwave sources. Meters of this type are made by several manufacturers, but all have
similar characteristics of being small, portable, and indicating average power in mW/cm2.
Some have optional combinations of antennas and power ranges which permit measurements
in the frequency range of 10 MHz to 18 GHz over the power range of 0.2 to 200 mW/cm2.
D-10.1.1 Radiation hazard meters are designed for simplicity of operation. It is important,
however, that the user become familiar with the manufacturers instructions to be aware of any
instrument limitations. The antennas, or probes, are characteristically easily damaged. They
have both a maximum average power and a maximum peak power rating. Depending upon the
duty cycle, it may be possible to damage the antenna by high peak power without exceeding the
average power limit. In most cases, damage can occur even if the instrument is in the "off"
position or the antenna is not connected.
D-10.1.2 Another precaution is to be aware of the response time of the instrument. The
response time is the time required for the meter indication to reach 90 percent of its final steadystate value. If the radiating antenna is rotating rapidly or the instrument antenna is moved
quickly, the reading may be significantly below the correct value.
D-10.1.3 Changes in the state-of-the-art and Navy requirements may result in changes of
recommended instrumentation. Those activities having a need for instrumentation should
consult their test equipment allowance list. For additional information relative to suitable
instrumentation, contact Naval Sea Systems Command (SEA-04H), Washington, DC.
D-10.2 POWER METER AND ANTENNA METHOD. Power density can also be measured
using an RF power meter, a calibrated antenna, and suitable attenuation. This measurement
technique is somewhat cumbersome; however, since laboratory-type components can be used,
it is possible to make accurate measurements over wide frequency and power ranges. The
basic RF power meter measures power in mW. When an antenna is connected to the power
meter and the capture area (effective area) of the antenna is known, then the power density in
mW/cm2 can be obtained.
D-10.2.1 Power Meter. RF power meters, such as the Hewlett Packard (HP) Model 432B, may
be used for power density measurements. These instruments, or commercial equivalents, are
D-31

required for the maintenance of many radars and are readily available. They typically are
capable of operating from internal batteries, have a 50-ohm input, and have multiple power
ranges with full-scale readings from 10 W to 10 mW.
D-10.2.2 Antennas. Power-density measurements can only be made if the effective area of
the test antenna is known or can be determined. In most cases, the test antenna will be a
standard gain waveguide horn, although any type can be used if its characteristics are known.
When the effective area of an antenna is not known, it can be computed from:
2
G
A ( eff ) = ---------4
or, for a resonant dipole, the effective area may be determined by:
8
1.175 10 A ( eff ) = --------------------------2

f
where:
A (eff) = effective area in cm2,

G = gain of antenna (power ratio),
= wavelength in cm, and
= frequency in MHz.
D-10.2.3 Attenuators. For most instruments, it will be necessary to attenuate the signal picked
up by the antenna so it will not exceed the limits of the power meter. The attenuation can be
obtained using either a directional coupler with appropriate termination or an in-line attenuator.
In either case, both the frequency and the power ratings must be correct. The typical 2-watt
coaxial attenuators supplied with power meters, signal generators, etc., may not be suitable
because of their lower power ratings. The required power rating for either a directional coupler
termination or an in-line attenuator can be approximated by multiplying the expected power
density by the effective area of the antenna. Coaxial cables used to interconnect the RF
components will attenuate the signal, and this attenuation becomes a part of the total
attenuation.
D-10.3 POWER DENSITY MEASUREMENTS. Power density measurements may be made
using a power meter such as the HP Model 432B and the following general method of
operation:
a. Determine the frequencies at which the measurements are to be made. Select the
proper horn antenna or dipole antenna elements and directional coupler or attenuator according
to frequency band designation. To avoid damage to the meter, use an attenuator or directional
coupler having the maximum attenuation for initial measurement.
D-32

b. Interconnect the antenna and power meter using coaxial cables and attenuators as
required.
c. Orient the pickup antenna for maximum reading on the meter.
d. Take reading as required.
NOTE
Make sure the pickup antenna is positioned such that it has the same
polarization as the radiating antenna. In the event the radiating antenna is
circularly polarized and the test antenna is not, the reading should be
doubled.
Certain power meters are not designed to operate in high RF fields. In
some cases, RF energy may penetrate the equipment case and prevent
the meter from reading zero with no input. It may be necessary to either
wrap the meter in aluminum foil for additional shielding or use a long
coaxial cable to the antenna and place the meter in a reduced field.
D-10.4 EXAMPLE POWER MEASUREMENT. An example of power-density measurement is
illustrated in figure D-14.
D-33

Assume the following data:

a. Radar Frequency - 3250 MHz
b. Pickup Antenna - Waveline Horn Model 299
c. Connecting Cables - 10 feet of RG-9A/U
d. Directional Coupler - Narda Model 3003-20
e. Power Meter - HP Model 432B
f. Meter Reading - 1.5 mW
From the proper charts and curves, the following data was obtained:
a. Effective area of pickup antenna at 3250 MHz - 213 cm2
(obtained from graph of Waveline Horn Model 299)
b. Directional coupler attenuation at 3250 MHz - 20 dB
(obtained from table for Narda Directional Coupler 3003-20)
c. Cable attenuation at 3250 MHz - 1.8 dB
(obtained from graph for RG-9A/U cable)
Total attenuation = cable attenuation + directional coupler attenuation = 20 dB + 1.8 dB = 21.8
dB. From figure D-12, 21.8 dB = a power ratio of 151.4. Therefore,
Ratio x Meter Reading (mW)
Power Density = Power
Effective Area of Pickup Antenna
151.4 1.5mW= -----------------------------------2

213cm
= 1.06mW cm
Figure D-14. Example of a Power Density Measurement
D-34
To expedite a response also mail a copy to: Director, Naval Surface Warfare Center, Indian Head Division Detachment
Earle, 201 Highway 34 South, Colts Neck, NJ 07722-5023, Attn: Code E421.
IF YOU PREFER TO FILL THIS FORM ONLINE CLICK ANYWHERE ON THIS TITLE
IF YOU WOULD LIKE A COPY OF THIS TMDER IN MICROSOFT WORD FORMAT CLICK ANYWHERE ON THIS TITLE
(Insert Classification of TMDER Here) CLASSIFICATION
Ref: NAVSEAINST 4160.3A

NAVSEA S0005-AA-GYD-030/TMMP
NAVSEA/SPAWAR TECHNICAL MANUAL DEFICIENCY/EVALUATION REPORT (TMDER)

INSTRUCTION: Continue on 8 1/2" x 11" paper if additional space is needed.
1. USE THIS REPORT TO INDICATE DEFICIENCIES, PROBLEMS, AND RECOMMENDATIONS RELATION TO PUBLICATIONS.
2. FOR CLASSIFIED TMDERS, SEE OPNAVINST 5510H FOR MAILING CLASSIFIED TMDERS.
2. VOL/PART
1. PUB NO.
NAVSEA OP 3565
3. REV. NO./DATE OR TM
CH. NO./DATE
4. SYSTEM/EQUIPMENT IDENTIFICATION
Sixth Rev/1 February 2003

6. REPORT CONTROL NUMBER
5. TITLE
ELECTROMAGNETIC RADIATION HAZARDS (U) (HAZARDS TO

PERSONNEL, FUEL AND OTHER FLAMMABLE MATERIAL) (U)
7. RECOMMENDED CHANGES TO PUBLICATION
PAGE
NO.
A
PARAGRAPH
B
8. ORIGINATORS NAME AND WORK

CENTER (Please Print)
C. RECOMMENDED CHANGES AND REASONS
9. DATE
10. DSN/COMM NO.
12. SHIP HULL NO. AND/OR STATION ADDRESS (Do Not Abbreviate)
NAVSEA 4160/1 (REV 8-95)(Destroy Old Stock)
11. TRANSMITTED TO
PLEASE CLOSE WITH TAPE - DO NOT STAPLE - THANK YOU
FOLD HERE
------------------------------------------------------------------------------------------------------------------------------------------DEPARTMENT OF THE NAVY
=================
Official Business
COMMANDER
NSDSA CODE 5B00
NAVSURFWARCENDIV
4363 MISSILE WAY
PORT HUENEME, CA 93043-4307
------------------------------------------------------------------------------------------------------------------------------------------FOLD HERE
NAVSEA 4160/1 (REV 8/95) BACK

Navsea Op 3565 Vol 1

Uploaded by

Copyright:

Available Formats

Navsea Op 3565 Vol 1

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Navsea Op 3565 Vol 1

Uploaded by

Copyright:

Available Formats

What is the purpose of this technical manual?

What is the purpose of this technical manual?

What information does this manual provide regarding electromagnetic radiation hazards?

What information does this manual provide regarding electromagnetic radiation hazards?

NAVSEA OP 3565/NAVAIR 16-1-529 VOLUME 1

ELECTROMAGNETIC RADIATION HAZARDS (U)(HAZARDS

THIS PUBLICATION SUPERSEDES NAVSEA OP 3565/NAVAIR 16-1-529

This page left intentionally blank

NAVSEA OP 3565/NAVAIR 16-1-529 VOLUME 1

ELECTROMAGNETIC RADIATION HAZARDS (U)(HAZARDS

THIS PUBLICATION SUPERSEDES NAVSEA OP 3565/NAVAIR 16-1-529

NAVSEA OP 3565/NAVAIR 16-1-529

This page left intentionally blank

NAVSEA OP 3565/NAVAIR 16-1-529

This page left intentionally blank

NAVSEA OP 3565/NAVAIR 16-1-529

Purpose and Scope of Manual ..................................................................... 1-1

CHAPTER 2 HAZARDS OF ELECTROMAGNETIC RADIATION TO PERSONNEL....... 2-1

Introduction .................................................................................................. 2-1

NAVSEA OP 3565/NAVAIR 16-1-529

Aircraft Radar Hazards. ................................................................................ 2-8

CHAPTER 3 RF BURNS ................................................................................................... 3-1

Scope ........................................................................................................... 3-1

CHAPTER 4 BIOLOGICAL RADIATION HAZARD FROM LASER DEVICES ................ 4-1

Introduction .................................................................................................. 4-1

CHAPTER 5 IONIZING RADIATION................................................................................. 5-1

Introduction .................................................................................................. 5-1

NAVSEA OP 3565/NAVAIR 16-1-529

Introduction and Background ....................................................................... 6-1

APPENDIX A DEFINITIONS AND ABBREVIATIONS....................................................... A-1

NAVSEA OP 3565/NAVAIR 16-1-529

RADHAZ Warning Sign Formats............................................................................. 2-4

Electrical Equivalent of Cargo-Handling Equipment................................................ 3-2

NAVSEA OP 3565/NAVAIR 16-1-529

Fresnel Region Gain Correction for Cosine Square

NAVSEA OP 3565/NAVAIR 16-1-529

Shipboard Communication and Satellite Systems .................................................. 2-10

NAVSEA OP 3565/NAVAIR 16-1-529

This page left intentionally blank

NAVSEA OP 3565/NAVAIR 16-1-529

PURPOSE AND SCOPE OF MANUAL

1-2.1 RF HAZARDS TO PERSONNEL. Radiation from antennas fed by high-powered RF

NAVSEA OP 3565/NAVAIR 16-1-529

NAVSEA OP 3565/NAVAIR 16-1-529

NAVSEA OP 3565/NAVAIR 16-1-529

NAVSEA OP 3565/NAVAIR 16-1-529

PRECAUTIONS TO ENSURE THE SAFETY OF PERSONNEL

It is the responsibility of the commanding officer of each ship or shore station to

NAVSEA OP 3565/NAVAIR 16-1-529

RADIO FREQUENCY AND LASER OVEREXPOSURE REPORTING REQUIREMENTS

Report all RF overexposure incidents in accordance with the requirements of

DEFINITIONS AND ABBREVIATIONS

A list of reference documents applicable to this volume is presented in appendix B.

NAVSEA OP 3565/NAVAIR 16-1-529

This page left intentionally blank

NAVSEA OP 3565/NAVAIR 16-1-529

2-1.1 GENERAL. This chapter discusses the hazards of electromagnetic radiation to

EMR HAZARDS TO PERSONNEL

2-2.1 PERMISSIBLE EXPOSURE LIMITS (PELS).

NAVSEA OP 3565/NAVAIR 16-1-529