Dec Lab Manual

Experiment No.
3
Design of Various Code Converters
Aim:
To Design Binary to Gray ,Gray to Binary , BCD to Excess 3, Excess 3 to BCD
code converters.
Objectives:
1.
2.
3.
To understand different codes

To design various Code converters using logic gates
To understand the importance of code converters in real life applications
Theory
Binary Codes
A symbolic representation of data/ information is called code. The base or radix of the binary number is 2. Hence, it
has two independent symbols. The symbols used are 0 and 1. A binary digit is called as a bit. A binary number consists of
sequence of bits, each of which is either a 0 or 1. Each bit carries a weight based on its position relative to the binary point.
The weight of each bit position is one power of 2 greater than the weight of the position to its immediate right. e. g. of binary
number is 100011 which is equivalent to decimal number 35.
BCD Codes
Numeric codes represent numeric information i.e. only numbers as a series of 0s and 1s. Numeric codes used to
represent decimal digits are called Binary Coded Decimal (BCD) codes. A BCD code is one, in which the digits of a decimal
number are encoded-one at a time into group of four binary digits. There are a large number of BCD codes in order to
represent decimal digits0, 1, 2 9, it is necessary to use a sequence of at least four binary digits. Such a sequence of binary
digits which represents a decimal digit is called code word.
Gray Codes
It is a non-weighted code; therefore, it is not a suitable for arithmetic operations. It is a cyclic code because
successive code words in this code differ in one bit position only i.e. it is a unit distance code.
Applications of Gray Code:
In instrumentation and data acquisition systems, where linear or angular displacement is measured.
In shaft encoders, input-output devices, A/D converters and the other peripheral equipment.
Excess-3 code
It is a non-weighted code. It is also a self-complementing BCD code used in decimal arithmetic units. The Excess-3
code for the decimal number is performed in the same manner as BCD except that decimal number 3 is added to the each
decimal unit before encoding it to binary.
Code Converters
The availability of a large variety of codes for the same discrete elements of information results in the use of different
codes by different digital systems. It is some time necessary to use the output of one system as the input to the other. The
conversion circuit must be inserted between the two systems if each uses different codes for the same information. Thus a
code converter is a circuit that makes the two systems compatible even though each uses the different code.
Binary to Gray code

Truth Table:
No
Binary
Gray
G3
G2
G1
3
4
0
0
0
1
1
0
1
0
0
0
0
1
1
1
0
0
7
8
0
1
1
0
1
0
1
0
0
1
1
1
1
0
0
0
10
11
12
13
14
15
1
1
1
1
1
1
0
1
1
1
0
1
1
1
1
0
0
0
1
0
0
1
1
0
Equations:
Diagram: Logic diagram for Binary to Gray Convertor is given below:
Gray to Binary code:

Truth Table:
G0
No
Gray
Binary
G3
G2
G1
G0
2
3
4
5
0
0
0
0
0
0
1
1
1
1
1
1
1
0
0
1
0
0
0
0
0
0
1
1
1
1
0
0
0
1
0
1
6
7
8
9
0
0
1
1
1
1
1
1
0
1
0
0
1
0
0
1
0
0
1
1
1
1
0
0
1
1
0
0
0
1
0
1
10
11
1
1
1
1
1
1
1
0
1
1
0
0
1
1
0
1
12
13
14
15
1
1
1
0
0
0
1
0
0
1
1
0
1
1
1
1
1
1
0
1
1
1
0
1
Equations:
Diagram: Logic diagram Gray to Binary Converter
BCD to Excess-3 :
To convert from binary code A to binary code B, the input lines must supply the bit combination of elements as
specified by code A and the output lines must generate the corresponding bit combination of code B. A combinational circuit
performs this transformation by means of logic gates. As we want to design 4-bit code, we must use four input variables and
four output variables. Designate the four input binary variables by the symbols A,B,C,D, and the four output variables by w,
x, y, and z. The truth table relating the input and output variables is as shown. A two-level logic diagram may be obtained
directly from the Boolean expressions derived by the maps. The expressions obtained may be manipulated for the purpose of
using common gates for two or more outputs. This manipulation illustrates flexibility obtained with multiple-output systems
when implemented with three or more levels of gates.
Truth table:
Decimal
Digit
BCD
Excess-3
B3
B2
B1
B0
E3
E2
E1
E0
Equations:
z=D
y = CD+CD=CD(C+D)
x = BC+BD+BCD= B(C+D) +BCD
x = B(C+D) +B(C+D)
w= A+BC+BD=A+B(C+D)
Diagram: Logic Diagram for BCD to Excess-3 Code Converter
Excess-3 to BCD :
The truth table relating the input and output variables is as shown.
Decimal
Digit
Excess-3
BCD
E3
E2
E1
E0
B3
B2
B1
B0
Equations:
Diagram: Logic Diagram for Excess-3 to BCD Code Converter
Procedure:
1.
2.
3.
Select appropriate code converter from tab menu.

Run / execute the simulation by pressing the run button and observe the output of code converters on the output LED.
Repeat the procedure for different inputs and note down the corresponding outputs.
Results
Binary to gray, gray to binary, Binary coded decimal (BCD) to Ex-3 code converter are simulated and the truth table are
verified.
Conclusion
Using basic logic gates, universal logic gates and derived logic gates different code converters can be implemented
and simulated.

Dec Lab Manual

Uploaded by

Copyright:

Available Formats

Dec Lab Manual

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Dec Lab Manual

Uploaded by

Copyright:

Available Formats

Experiment No.

To Design Binary to Gray ,Gray to Binary , BCD to Excess 3, Excess 3 to BCD

To understand different codes

Binary to Gray code

Diagram: Logic diagram for Binary to Gray Convertor is given below:

Gray to Binary code:

Diagram: Logic diagram Gray to Binary Converter

Diagram: Logic Diagram for Excess-3 to BCD Code Converter

Select appropriate code converter from tab menu.

You might also like