WRT-416 Router
WRT-416 Router
User manual
WRT-416
Users Manual
Page 1 of 47
User manual
Copyright
Copyright 2007 by PLANET Technology Corp. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any
software described in this manual is sold or licensed "as is". Should the programs prove defective following
their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes the entire cost of all
necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the
software. Further, PLANET reserves the right to revise this publication and to make changes from time to
time in the contents hereof without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of
their respective holders.
FCC Caution
To assure continued compliance. (example-use only shielded interface cables when connecting to
computer or peripheral devices). Any changes or modifications not expressly approved by the party
responsible for compliance could void the users authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two conditions:
( 1 ) This device may not cause harmful interference, and ( 2 ) this Device must accept any interference
received, including interference that may cause undesired operation.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However,
special attention must be paid to the dangers of electric shock and static electricity when working with
electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all
Page 2 of 47
User manual
WEEE Regulation
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and
electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do
not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
Users Manual for PLANET Wireless Broadband Router
Model: WRT-416
Rev: 1.0 (October, 2007)
Part No. EM-WRT416
Page 3 of 47
User manual
Table of Contents
Chapter 1 Introduction.................................................................................................... 6
1.1 Package Content ....................................................................................................... 6
1.2 System Requirement ................................................................................................. 6
1.3 Features..................................................................................................................... 6
1.4 Wireless Performance................................................................................................ 7
Chapter 2 Hardware Installation .................................................................................... 8
2.1 Hardware Connection ................................................................................................ 8
2.2 LED Indicators ........................................................................................................... 8
2.3 Back View .................................................................................................................. 9
Chapter 3 Configuring Local Networking ................................................................... 10
3.1 Setting up TCP/IP .................................................................................................... 10
3.1.1 Windows 2000 ............................................................................................... 10
3.1.2 Windows XP/2003 ......................................................................................... 13
3.2 Additional Settings for Wireless Client ..................................................................... 16
3.3 Checking PCs IP and Connection with the Router .................................................. 17
Chapter 4 Web Configuration ...................................................................................... 19
4.1 Status....................................................................................................................... 20
4.1.1 System Status................................................................................................ 20
4.1.2 Statistics ........................................................................................................ 22
4.2 WAN Setup .............................................................................................................. 23
4.2.1 Dynamic IP Address ...................................................................................... 24
4.2.2 PPPoE ........................................................................................................... 24
4.2.3 Static IP ......................................................................................................... 25
4.2.4 PPTP ............................................................................................................. 27
4.2.5 L2TP .............................................................................................................. 28
4.3 LAN Setup................................................................................................................ 28
4.3.1 LAN Setup ..................................................................................................... 28
4.3.2 DHCP IP Address Reserving ......................................................................... 29
4.3.3 DHCP Info...................................................................................................... 29
4.4 Wireless ................................................................................................................... 30
4.4.1 Basic Settings ................................................................................................ 30
4.4.2 Security.......................................................................................................... 31
4.4.3 Filter List ........................................................................................................ 34
4.4.4 WDS .............................................................................................................. 35
4.4.5 Advanced....................................................................................................... 36
4.4.6 Association Table .......................................................................................... 36
4.5 Routing .................................................................................................................... 37
4.6 NAT.......................................................................................................................... 37
4.6.1 DMZ Host Setup ............................................................................................ 38
4.6.2 FTP Private Port ............................................................................................ 39
4.6.3 Virtual Server Setup....................................................................................... 39
4.6.4 Port Trigger.................................................................................................... 40
4.7 Fire Wall................................................................................................................... 40
4.7.1 MAC Filtering ................................................................................................. 40
4.7.2 Access Control............................................................................................... 41
4.7.3 URL Filtering.................................................................................................. 42
4.7.4 Ping................................................................................................................ 43
4.8 DDNS....................................................................................................................... 44
4.9 MISC........................................................................................................................ 44
4.9.1 Login ID & Password Setup ........................................................................... 44
4.9.2 Remote Mgmt ................................................................................................ 45
Page 4 of 47
User manual
Page 5 of 47
User manual
Chapter 1 Introduction
Thank you for purchasing WRT-410. This device features the latest innovation wireless technology making
the wireless networking world happened. This manual guides you on how to install and properly use the
WRT-410 in order to take full advantage of its features.
One WRT-416
One dipole antenna
One Ethernet cable
One AC Power Adapter
One Users Manual CD
One Quick Installation Guide
Note:
If any of the above items are missing, contact your supplier as soon as
possible.
1.3 Features
Page 6 of 47
User manual
Page 7 of 47
User manual
Before you proceed with the installation, it is necessary that you have enough information about the
WRT-416.
LED
STATE
MEANING
PWR/SYS
Green
Device power on
WAN
Green
Blinking Green
WAN activity
Green
Link is established
Blinking Green
Green
Link is established
Blinking Green
LAN 1
Page 8 of 47
User manual
Green
Link is established
Blinking Green
Green
Link is established
Blinking Green
Power (DC 9V): The receptacle where you plug in the power adapter.
WAN: Connect your modem to your router using this port with your supplied Ethernet cable. This is the only
port you can use for this procedure. This enables your router to access the Internet. The port supports 10/100
Mbps as well as straight-through and crossover Ethernet cables.
LAN Ports 1-4: These four ports connect the router to your LAN or home network using Ethernet cables. This
enables communication among clients, such as PCs, on the network. The LAN ports support either
10-BASE-T or 100-BASE-T transmission speeds as well as straight-through and crossover Ethernet cables.
Any of these four ports can also serve as an uplink port to other network devices, such as another router or
switch, which allows you to extend your network.
Reset button: Resets your router or resets the router to the default login settings.
To reset the AP to the factory defaults, press and hold the Reset button for more than five
seconds. This clears the APs user settings, including User ID, Password, IP Address, and
Subnet mask. (Warning: your original configurations will be replaced with the factory default
settings).
Antenna: The antenna used for wireless connections. You are able to rotate the antenna to gain the best
signal reception.
Page 9 of 47
User manual
You can manage the WRT-416 through the Web browser. To configure the device via Web browser, at least
one properly configured computer must be connected to the device via Ethernet (recommended) or wireless
network. The WRT-416 is configured with the default IP address of 192.168.1.1 and subnet mask of
255.255.255.0 and its DHCP server is disabled by default.
Page 10 of 47
User manual
Step 5: Choose Obtain an IP address automatically and Obtain DNS Server Address automatically, and then
press OK to close the Internet Protocol (TCP/IP) Properties window.
Page 11 of 47
User manual
Page 12 of 47
User manual
Page 13 of 47
User manual
Step 4: Highlight the icon Local Area Connection, right click your mouse, Click Properties
Page 14 of 47
User manual
Step 6: Choose Obtain an IP address automatically and Obtain DNS Server address automatically, and then
press OK to close the Internet Protocol (TCP/IP) Properties window.
Page 15 of 47
User manual
SSID: default
Authentication: Disabled
Encryption: Off
Page 16 of 47
User manual
For Windows 98/Me: Start -> Run. Type command and click OK.
For Windows 2000/XP: Start -> Run. Type cmd and click OK.
Then the connection between the router and your computer has been successfully established.
If the computer fails to connect to the router, the Command window will return the following:
Page 17 of 47
User manual
Verify your computer's network settings are correct and check the cable connection between the router and
the computer.
Page 18 of 47
User manual
Web configuration provides a user-friendly graphical user interface (web pages) to manage your WRT-416.
An AP with an assigned IP address (e.g. http://192.168.1.1) will allow you to monitor and configure (via web
browser e.g., MS Internet Explorer or Netscape).
1. Open your web browser.
2. Enter WRT-416 IP address (default IP address is http://192.168.1.1) into the address field of the web
browser. Please also make sure your PCs IP address is in the same IP range with WRT-416.
If the routers LAN port has been changed with new IP address, enter the new IP address instead.
3. A User Name and Password dialog box will appear. Please enter your User Name and Password here.
The User Name and Password are guest by default. Click OK the management page.
Dont forget to change the Password in configurations Authentication to ensure the security. When
first configuring your router, it is recommended that you have an Ethernet cable connected to the router.
Performing the INITIAL configuration using a wireless connection is not secure and is not recommended.
After you have finished the initial configuration of the router, your connection will be secure and you can
safely use either a wired or wireless connection.
On every page of the Wireless Router, the left navigation bar shows the main options to configure the
system. In the right navigation screen is the summary of system status for viewing the configurations.
You can usually get context sensitive help by clicking on the Help link at the top right of the page.
To apply any settings youve altered on any page, click the Save button. Otherwise you change
settings would be lost after the Router reboot.
Page 19 of 47
User manual
4.1 Status
4.1.1 System Status
This page shows most of the basic configuration parameters of the Router. It is the first page shown after
login.
WAN Status: This section shows the WAN interface parameters of the wireless router. This includes
information such as:
Connection type (DHCP, PPPoE or Static IP)
The MAC address of WAN interface
IP/Subnet Mask
Default Gateway
Primary DNS
Backup DNS
PPPoE: In PPPoE mode, if you want to start a connection, click on the Connect button to build a
PPPoE session.
Page 20 of 47
User manual
DHCP: In DHCP mode, press "Disconnect" button to release IP address and press "Connect" button to
renew IP address.
LAN Status: This section shows the LAN interface parameters of the wireless router. This includes
information such as:
The MAC address of LAN interface
IP/Subnet Mask
DHCP Server status
Page 21 of 47
User manual
Wireless Status: This section shows the WLAN interface parameters of the wireless router. This
includes information such as:
Wireless status
Connection status
The MAC address of WLAN interface
Radio Band
SSID
Channel number
Security mode
System Information: This section shows the installed version of the firmware of the WRT-416.
4.1.2 Statistics
The statistics tab contains following items for monitoring network traffic between interface of types external
(WAN) and internal (LAN and WLAN), and display System Run Time.
Page 22 of 47
z
z
User manual
System Run Time: Display the active duration since system start up.
Statistics: You can monitor current sent & received packets counters of wireless and Ethernet
networks .To see the latest information, click Refresh button.
Page 23 of 47
User manual
z
z
Clone MAC: Your ISP may require a particular MAC address in order for you to connect to the Internet
only. This MAC address is the PCs MAC address that your ISP had originally connected your Internet
connection to. Type in your PCs MAC address in this section to replace the WAN MAC address of
WRT-416 (you have to be using that PC for the Clone MAC Address button to work).
MTU: MTU is the Maximum Transmission Unit. It specifies the largest packet size permitted for Internet
transmission. Enter your MTU number in the text-box to set the limitation. The recommended size,
entered in the Size field, is 1496. You should leave this value in the 1200 to 1500 range.
DNS: Check "DNS" and enter the IP address to specify DNS server for LAN DHCP server.
Click Apply to save these settings with the Router. The System will apply the new settings and start
rebooting right away. After reboot, the Wireless Router will enable these settings with the Router.
4.2.2 PPPoE
Some DSL-based ISPs use PPPoE (Point-to-Point Protocol over Ethernet) to establish Internet connections.
If you are connected to the Internet through a DSL line, check with your ISP to obtain all necessary
information.
Page 24 of 47
z
z
z
z
z
z
User manual
PPPoE Account: Enter the User Name provided by your ISP for the PPPoE connection
PPPoE Password: Enter the Password provided by your ISP for the PPPoE connection
Clone MAC: Your ISP may require a particular MAC address in order for you to connect to the Internet.
This MAC address is the PCs MAC address that your ISP had originally connected your Internet
connection to. Type in this MAC address in this section to replace the WAN MAC address with the MAC
address of that PC (you have to be using that PC for the Clone MAC Address button to work).
MTU: MTU is the Maximum Transmission Unit. It specifies the largest packet size permitted for Internet
transmission. Enter your MTU number in the text-box to set the limitation. The default value of MTU is
1492 and use 1300 while the line condition is bad.
DNS: Check "DNS" and enter the IP address to specify DNS server for LAN DHCP server.
Connection Type: Select your PPPoE connection from these options:
Connect to Internet automatically: This feature will keep your Internet connection always alive.
The Router will periodically check your Internet connection. If you are disconnected, then the
Router will automatically re-establish your connection. To use this option, click the radio button
next to Auto Connect.
Auto disconnect when idle, time out: If enabled, the router will trigger a PPPoE session for
connection to the Internet if any client PC on your WLAN/LAN sends out a request for Internet
access. However, the router automatically disconnects the PPPoE session after the WAN
connection has been idle for the amount of time you specified in the timeout box. If your Internet
account is billed based on the amount of time of your Internet connection, you probably want to
enable this option and enter an idle time value best suitable for your network. To use this option,
click the radio button next to Connect on demand.
Connect to Internet manually: The router will connect to Internet while click the Connect button
on the Web. And the WAN connection will disconnect. If you click Disconnect manually from the
Web user interface. The router will not auto-connect to the Internet. To use this option, click the
radio button next to Connect on demand.
Click Apply to save these settings with the Router. The System will apply the new settings and start
rebooting right away. After reboot, the Wireless Router will enable these settings with the Router.
4.2.3 Static IP
If you are required to use a permanent IP address to connect to the Internet, select Static IP.
Page 25 of 47
z
z
z
z
z
z
User manual
WAN IP Address: This is the Routers IP address, when seen from the Internet. Your ISP will provide
you with the IP Address you need to specify here.
Subnet Mask: This is the Routers Subnet Mask, as seen by users on the Internet (including your ISP).
Your ISP will provide you with the Subnet Mask.
Default Gateway: Your ISP will provide you with the Gateway Address, which is the ISP servers IP
address.
Physical Address Clone: Your ISP may require a particular MAC address in order for you to connect to
the Internet. This MAC address is the PCs MAC address that your ISP had originally connected your
Internet connection to. Type in this MAC address in this section to replace the WAN MAC address with
the MAC address of that PC (you have to be using that PC for the Clone MAC Address button to work).
MTU: MTU is the Maximum Transmission Unit. It specifies the largest packet size permitted for Internet
transmission. Enter your MTU number in the text-box to set the limitation. The recommended size,
entered in the Size field, is 1496. You should leave this value in the 1200 to 1500 range.
DNS: Check "DNS" and enter the IP address to specify DNS server for LAN DHCP server.
Click Apply to save these settings with the Router. The System will apply the new settings and start
rebooting right away. After reboot, the Wireless Router will enable these settings with the Router.
Page 26 of 47
User manual
4.2.4 PPTP
z
z
z
z
z
z
z
z
z
Click Apply to save these settings with the Router. The System will apply the new settings and start
rebooting right away. After reboot, the Wireless Router will enable these settings with the Router.
Page 27 of 47
User manual
4.2.5 L2TP
z
z
z
z
z
z
z
z
z
Click Apply to save these settings with the Router. The System will apply the new settings and start
rebooting right away. After reboot, the Wireless Router will enable these settings with the Router.
Page 28 of 47
z
z
User manual
IP Address/Subnet Mask: Enter the IP address and subnet mask for the Wireless Broadband Router
LAN port. All local wired/wireless devices communicate with the device through this port. By default, the
IP address and subnet mask of the LAN port is 192.168.1.1 and 255.255.255.0 respectively.
DHCP Server: The DHCP server can be ON or OFF in this screen. If you choose to set this device as a
DHCP server, it will assign IP addresses to its clients. The DHCP pool range is also changeable.
Click Apply when you have finished the configuration above. And the wireless router will be automatically
restarted if you change the LAN IP address.
If you change the private IP address and apply the changes, the PC from which you configure the
router will lose the communication to the router. To reconnect, you will need to renew the IP address of the
PC or change to an IP address compatible with the new LAN port IP address.
Page 29 of 47
User manual
4.4 Wireless
The WRT-416 implements Access Point capability, which connects wireless clients to a wired LAN. It allows
wireless stations to access network resources and share the broadband Internet connection.
z
z
z
z
Radio Band: The default setting is mixed mode [802.11B/G]. If you do not know or have both 11g and
11b devices in your network, then keep the default in mixed mode. From the drop-down manual, you
can select 802.11G if you have only 11G card. If you have only 802.11 B card, then select 802.11B.
Radio Mode: The Route has 3 modes: AP, WDS, AP+WDS. If WDS or AP+WDS is selected, please go
to WDS tab to complete related settings.
Booster Mode: Enabled this mode can enhance the throughput of data transmission.
SSID: The SSID is the network name shared among all points in a wireless network. The SSID must be
identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters
(use any of the characters on the keyboard). Make sure this setting is the same for all points in your
wireless network. For added security, you should change the default SSID (default) to a unique name.
Channel: Select the channel used for wireless communication. There are 11 overlapping channels.
Channels 1, 6 and 11are non-overlapping. The default is channel 6.
Page 30 of 47
User manual
4.4.2 Security
This wireless router provides complete wireless LAN security functions; include WEP, WPA with pre-shared
key and WPA2 with pre-shared key. With these security functions, you can prevent your wireless LAN from
illegal access. Please make sure your wireless stations use the same security function.
4.4.2.1 None
Transmit data without encryption and authentication. This is the default option.
If you select none, any data will be transmitted without Encryption and any station can access the
wireless router.
4.4.2.2 WEP
WEP (Wired Equivalent Privacy) is an encryption method used to protect your wireless data communications.
WEP uses a combination of 64-bit or 128-bit keys to provide access control to your network and encryption
security for every data transmission.
Page 31 of 47
z
z
z
z
z
z
z
User manual
Key Length
HEX Format
ASCII Format
64 Bit
10 hexadecimal digits
5 ASCII characters
128 Bit
26 hexadecimal digits
13 ASCII characters
Click Apply at the bottom of the screen to save the above configurations.
Page 32 of 47
z
z
z
z
User manual
TKIP: Temporal Key Integrity Protocol (TKIP) utilizes a stronger encryption algorithm and includes
Message Integrity Code (MIC) to provide protection against hackers.
AES: Advanced Encryption System (AES) utilizes a symmetric 128-Bit block data encryption. Its the
strongest encryption currently available.
WPA Pass Phrase: The WPA Pass Phrase is used to authenticate and encrypt data transmitted in the
wireless network. The input format is in character style and key size should be in the range between 8
and 63 characters.
Rekey Time (sec): Specifies the timer the WPA key must changes. The change is done automatically
between the server and the client. The default value is 86400.
Click Apply at the bottom of the screen to save the above configurations.
AES: Advanced Encryption System (AES) utilizes a symmetric 128-Bit block data encryption. Its the
Page 33 of 47
z
z
User manual
Click Apply at the bottom of the screen to save the above configurations.
Click Apply at the bottom of the screen to save the above configurations.
Page 34 of 47
z
z
z
z
z
z
User manual
Enable Wireless Access Control: To enable Wireless MAC Filter, select the checkbox in front of
Enable Wireless Access Control, then click the Apply button. The default is disable.
You can choose a default operation for your factual security or management consideration:
Defined items in MAC list are PERMIT to connect AP, others are DENIED.
Defined items in MAC list are DENIED to connect AP, others are PERMIT.
Click Apply when you have selected,
MAC: Enter the MAC Address of a station.
Description: Enter the Comment of station.
Click "Add, then this wireless station will be added into the Current Access Control List" below.
If you want to remove some MAC address, select them from the list and then click "Delete ".
4.4.4 WDS
You can set the wireless Bridge MAC here. This mode is used to connect two or more WRT-416 or
WAP-4036 wirelessly.
z
z
z
Wireless Bridge MAC: If the operating mode of your WRT-416 is "WDS" or "AP+WDS", you should
have a setting in Wireless Bridge MAC. Enter the MAC address of target access point. Moreover, the
target access point must be "WDS" or "AP+WDS" as well.
Description: Enter the Comment of station.
Current Wireless Bridge Information: You can see the basic information of all wireless bridge devices.
And you can delete any wireless bridge in the list.
Page 35 of 47
User manual
4.4.5 Advanced
This tab is used to set up the Routers advanced wireless functions. These settings should only be adjusted
by an expert administrator as incorrect settings can reduce wireless performance.
z
z
z
z
Beacon Interval: This value indicates the frequency interval of the beacon. A beacon is a packet
broadcast by the wireless router to keep the network synchronized. A beacon includes the wireless LAN
service area, a time stamp, Delivery Traffic Indicator Maps, and the Traffic Indicator Message (TIM).
The default value is 100.
RTS Threshold: This value should remain at its default setting of 2,347. Should you encounter
inconsistent data flow, only minor modifications are recommended.
DTIM Interval: This value indicates how often the Access Point sends out a Delivery Traffic Indication
Message (DTIM). Lower settings result in more efficient networking, while preventing your PC from
dropping into power saving sleep mode. Higher settings allow your PC to enter sleep mode, thus saving
power, but interferes with wireless transmissions.
Transmit Rate: The Transmit Rate is the data packets limitation this wireless router can transmit, The
wireless router will use the highest possible selected transmission rate to transmit the data packets. The
default value is Auto.
Preamble Type: It defines the length of CRC block in the frames during the wireless Communication.
"Short Preamble" is suitable for heavy traffic wireless network. "Long Preamble" provides much
communication reliability
Page 36 of 47
User manual
4.5 Routing
If the Router is connected to more than one network, it may be necessary to set up a static route between
them. A static route is a pre-determined pathway that network information must travel to reach a specific host
or network.
z
z
z
z
Type / Target / Mask / Gateway: Fill in these fields required by this Static Routing function.
Add: Fill in the all of the setting to be added and click "Add", then this Special Application setting will be
added into the "Current Routing Table" below.
Current Routing Table: This display shows the valid routing paths in Broadband Router. User can view
the information about current routing paths
If you want to remove some route entries from the Current Routing Table ", select the Route entry you
want to remove in the table and then click "Delete ".
4.6 NAT
Network Address Translation (NAT) allows multiple users at your local site to access the Internet through a
single Public IP Address. NAT provides Firewall protection from hacker attacks and has the flexibility to allow
you to map Private IP Addresses to Public IP Addresses for key services such as Websites and FTP.
Page 37 of 47
User manual
z
z
Click Apply at the bottom of the screen to save the DMZ configurations.
If there is a conflict between the Virtual Server and the DMZ setting, then Virtual Server function will
have priority over the DMZ function.
Page 38 of 47
User manual
Check port number and enter the number and then press the "Apply" button to setup Private FTP port.
The default Value is 1025.
z
z
z
z
z
z
z
Rule Name: Define a name for this rule. It's just a string.
Internal Server IP: Enter the host IP address to which the packet will be forwarded. The virtual server
can be set easily by setting the internal server IP address only. You need to give your LAN PC clients a
fixed/static IP address for Virtual Server to work properly.
Protocol: Chose TCP/UDP type for the packet you want to forward. If the rule existed in predefined
virtual server rule, you can choose the rule.
External Port: Enter the port number (The value's range is 1 to 65535) from which the packet will be on
WAN.
Internal Port: Enter the port number to which the packet will be forwarded on LAN
Press "Add" button after enter the all fields to add the rule.
Check to select the rule and press "Delete" to delete the rule.
Page 39 of 47
User manual
z
z
z
z
z
z
z
Rule Name: Define a name for this rule. It's just a string.
Trigger Protocol: Chose TCP/UDP type for the packet you want to trigger. If the rule existed in
predefined virtual server rule, you can choose the rule.
Trigger Port: Enter the port number (The value's range is 1 to 65535) from which the packet will be on
WAN.
Forward Protocol: Chose TCP/UDP type for the packet you want to forward. If the rule existed in
predefined virtual server rule, you can choose the rule.
Forward Port: Enter the port number to which the packet will be forwarded on LAN
Press "Add" button after enter the all fields to add the rule.
Check to select the rule and press "Delete" to delete the rule.
Page 40 of 47
User manual
wired client. The user has the flexibility to customize your own control policy based on these options:
Figure 56
z
z
z
z
z
z
Enable MAC Filtering: To enable MAC Filtering, click the check box. The default is disable.
You can choose a default operation for your factual security or management consideration:
Defined items in MAC list are DENIED to access internet, others are PERMIT
Defined items in MAC list are PERMIT to access internet, others are DENIED
Click Apply when you have selected,
MAC: Enter the MAC Address of a station.
Description: Enter the Comment of station.
Click "Add. Then this wired station will be added into the Current Access Control List" below.
If you want to remove some MAC address, select the MAC address from the list and then click "Delete ".
Page 41 of 47
User manual
Enable Access Control: To filter the outgoing packets for security or management consideration by IP
Address, either permitting or blocking access, Enable Access Control is checked.
You can choose a default operation for your factual security or management consideration:
The Undefined items beside the Rule list are PERMIT to access internet DENIED to access internet.
The Undefined items beside the Rule list are DENIED to access internet DENIED to access internet.
Rule Name: Enter the rule name which you want, it is just only a string.
Source IP: Enter the IP address of a station which is you want to setting.
Predefined Applications: Chose the Predefined rule in the list to be allowed or forbade accessing Internet.
Protocol & Port: Chose protocol type (TCP/UDP) and enter the single port number or the port range to allow
or forbid.
Action: You can choose the rule is be allowed or denied accessing Internet.
Page 42 of 47
User manual
URLs/Keywords: Enter the specified URL site for security or management consideration by
URLs/Keywords, either permitting or blocking access.
4.7.4 Ping
This page defines rules to prevent WRT-416 WAN and LAN port being scanned.
Page 43 of 47
User manual
4.8 DDNS
DDNS allows you to map the static domain name to a dynamic IP address. You must get an account,
password and your static domain name from the DDNS service providers.
Figure 62
z
z
User ID/Password/Host Name: Enter your registered domain name and your username and password
for this service.
Information: The status of the DDNS service connection is displayed here. To see the latest DDNS
status, click Refresh button.
4.9 MISC
4.9.1 Login ID & Password Setup
In factory setting, the default password is guest, and that for user is also password. You can change the
default password to ensure that no one can adjust your settings without permission. Every time you change
your password, please record the password and keep it at a safe place.
Page 44 of 47
z
z
User manual
If you forget your password, youll have to reset the router to the factory default (Password is guest)
with the reset button (see routers front panel).
z
z
When you want to access the web-based management from a remote site, enter http:// WAN IP
Address:8080. (e.g:http://210.66.155.71:8080).
Page 45 of 47
User manual
Page 46 of 47
User manual
Appendix : Specification
Standard
Frequency Band
2.400~2.4835GHz
Transfer Rate
802.11g: 54/48/36/24/18/12/9/6Mbps
802.11b: 11/5.5/2/1Mbps
OFDM, CCK, QPSK and BPSK
Modulation
Antenna
Transmit Power
15dBm2dBm
Wireless Operating
Range
Sensitivity
Interface
LED Indicators
6; PWR/SYS,LAN(1~4),WAN
Power
9V DC, 700mA
Temperature
0 ~ 40C (Operating)
Humidity
Dimension
186mm*29mm*119mm
Weight
300g
Emission
Page 47 of 47