1701/15 Fieldmonitor™ Proximitor Input Monitor For Radial Vibration and Thrust Position

1701/15 FieldMonitor Proximitor Input Monitor
for Radial Vibration and Thrust Position

Bently Nevada Asset Condition Monitoring
Description
The 1701/15 FieldMonitor Proximitor Input Monitor is a 2-channel device that
accepts signals from proximity probes via its associated transducer I/O or
internal Proximitor module, conditions these signals into the appropriate
measurement units, compares them to user-programmable alarm setpoints, and
generates appropriate alarm signals for communication to the host control
system. It can also provide current values of its measured parameters to the
control system for indication and trending. Embedded self-tests permit the
monitor to assess its own integrity, and that of its connected transducers. A NOT
OK condition can be detected and annunciated when problems with the monitor
or its connected transducers exist.
The monitor can be programmed to provide any of the following measurements:
Shaft relative radial vibration
Shaft radial position (see note)
Shaft axial position (i.e., thrust position)
Note: Shaft radial position (i.e., gap voltage) is monitored simultaneously with shaft radial vibration
using the same monitor channel. However, only Alarm 1 (Alert) capabilities are provided as shaft
position measurements are normally not used for machinery protection purposes.
Specifications and Ordering Information

Part Number 141483-01
Rev. F (11/08)
Page 1 of 7
Specifications
1701/15 Proximitor Input Monitor - Radial
Vibration
Full-scale Direct
Ranges
mils pp:
0 - 3 mils
Programmable Options
0 - 5 mils
Proportional
Values:
0 - 10 mils
0 - 15 mils
Direct (Overall), Gap
0 - 20 mils
Alarms
micrometers pp:
Alarm 1 (Alert),
Alarm 2
(Danger):
0 - 100 m
0 - 125 m
Over Alarm 1 & 2 on Direct,

Over/Under Alarm 1 on Gap
0 - 150 m
0 - 200 m
Alarm Time
Delays:
0 - 250 m
0.15, 0.2, 0.3, 0.5, 0.6, 1.0, 2.0, 3.0,
5.0, 6.0, 10.0, 20.0 seconds
Latching/NonLatching
Alarms:
0 - 300 m
0 - 400 m
0 - 500 m
Non-Latching only
Full-Scale Gap
Range:
24 Volts
Trip Multiply:
None, 1.5, 2, 3
Gap Filter:
-3 db at 0.09 Hz
OK Mode:
Non-latching only
Barriers:
Always Enabled
Internal galvanically isolated barrier (requires

the 1701/06 Isolator Terminal Base)
External Zener Barrier
External galvanically isolated barrier
Timed OK
Channel Defeat:
Alarm
Hysteresis:
Supported Transducer I/O Modules

170133-050-XX
0.5% of full-scale
Internal 3300 5-metre Proximitor

transducer
Signal Processing Options

Bandwidth/Filtering
High-Pass
Corner
Frequency in Hz
170133-090-XX
transducer
1, 4
Low-Pass
Corner
Frequency in Hz
170133-014-XX
transducer
4000, 600
Rev. F (11/08)
Page 2 of 7
Control I/O
170150-070-00
Channel On/Off
Monitor Reset
Channel Inhibit
Trip Multiply: Enabled, Disabled
Internal 3300 NSv 7-metre

Proximitor transducer

transducer
Specifications at 25C (77F)
170172-050-XX
170172-090-XX
transducer
170190-01
Internal galvanically isolated
barrier
(requires the 1701/06 Isolator
Terminal Base)
Direct accuracy:
1% of full-scale max (exclusive of
filters)
Direct
resolution:
0.1% of full-scale
Gap accuracy:
20mV, -1 to -23 V
Gap Resolution:
170180-01-XX
1 mV
Proximitor / Accelerometer I/O

170180-05-XX
External -18 Volt Proximitor I/O
External Proximitor Options

I/O Module
Gap Setpoint
Resolution:
0.10 V
Power input:
-24 V, + 5 V, from 1701 Power
Supply
170180-01-XX
3300 5 mm
3300 8 mm
Power
Consumption:
1.5 Watt (not including
transducers)
330800 Proxpac
3300 XL
7200 5 mm
Setpoint
resolution:
7200 8 mm
7200 11 mm
7200 14 mm
0.5% of full-scale
Flex read/write
rate:
25 millisec (monitor to Flex
adapter)
3300 RAM
3300 XL NSv
170180-05-XX
Buffered
Output:
3000 -18 Volt
30 m (100 ft) cable at 60pF/ft, not

isolated
Output
impedance:
200

Rev. F (11/08)
Page 3 of 7
Physical
Latching/NonLatching
Alarms:
Dimensions
(HxWxD)
Non-Latching only
127 mm x 21.6 mm x 105 mm

(5 in x 0.85 in x 4.15 in)
OK Mode:
Non-Latching only
Weight:
314 g (0.69 lb)
Environmental Limits
Operating
Temperature:
-20C to + 70C (-4F to +158F)
Storage
Temperature:
Timed OK
Channel Defeat:
Always Disabled
Alarm
Hysteresis:
0.5% of full-scale
Signal Processing Options

-40C to + 85C (-40F to +185F)
Operating
Humidity:
Bandwidth/Filte
ring
Direct Filter:
5% to 95% non-condensing
relative humidity.
Storage
Humidity:
-3dB at 1.2 Hz
Gap Filter:
-3dB at 0.041 Hz
relative humidity.
1701/15 Proximitor Input Monitor - Thrust

Position
Full-scale Direct
Range
mils:
10 - 0 - 10
25 - 0 - 25
Programmable Options
30 - 0 - 30
Proportional
Values:
40 - 0 - 40
50 - 0 - 50
Direct, Gap
75 - 0 - 75
Alarms
millimeters:
Alarm 1 (Alert),
Alarm 2
(Danger):
0.250 - 0 - 0.250
0.500 - 0 - 0.500
Over/Under Alarm 1 & Alarm 2 on

Direct
0.600 - 0 - 0.600
0.800 - 0 - 0.800
Alarm Time
Delays:
1.0 - 0 - 1.0
0.15, 0.2, 0.3, 0.5, 0.6, 1.0, 2.0, 3.0,
5.0, 6.0, 10.0, 20.0 seconds
2.0 - 0 - 2.0
Full-scale Gap
Range:
24 Volts
Rev. F (11/08)
Page 4 of 7
External Proximitor Options
Normal Thrust
Direction:
170180-01-xx
Toward probe
3300 5 mm
Away from probe
3300 8 mm
Direct Zero
Position:
3300 XL
330800 Proxpac
Set using I/O data tables
7200 5 mm
Barriers:
7200 8 mm
Internal galvanically isolated barrier (requires

the 1701/06 Isolator Terminal Base)
External Zener Barrier
External galvanically isolated barrier
7200 11 mm
7200 14 mm
3300 RAM
Transducer I/O Module Options
3300 XL NSv
170133-050-XX
transducer
170133-090-XX
170180-05-xx
3000 -18 Volt
Control I/O
transducer
170133-014-XX
transducer
Channel On/Off
Monitor Reset
Channel Inhibit
Specifications at 25C (77F)

Direct accuracy:
1% of full-scale max, (exclusive of
filters)
170150-070-00
Internal 3300 NSv 7-metre
Proximitor Transducer
170172-050-XX
Transducer
Direct
Resolution:
0.1% of full-scale
Gap accuracy:
20mV, -1 to -23 V
170172-090-XX
transducer
170190-01
Gap Resolution:
1 mV
Power input:
Internal galvanically isolated

barrier (requires the 1701/06
Isolator Terminal Base)
170180-01-XX
-24 V, + 5 V, from 1701 Power

Supply
Power
Consumption:
Proximitor / Accelerometer I/O
1.5 Watt (not including

transducers)
170180-05-XX
External -18 Volt Proximitor I/O
Setpoint
resolution:
0.5% of full-scale
Rev. F (11/08)
Page 5 of 7
Flex read/write
rate:
Ordering Information
25 millisec (monitor to Flex
adapter)
Proximitor Input Monitor for Radial Vibration and Thrust

Position
1701/15-01
30 m (100 ft) cable at 60pF/ft, not

isolated
Hazardous Area Approvals
Buffered
Output:
North America
Output
impedance:
Ex nA IIC T4
200
Class I, Zone 2
Physical Dimensions
Class I, Div 2
(HxWxD):
Groups A, B, C, D
127 mm x 21.6 mm x 105mm
T4 @ -30C = Ta = +70C
(5 in x 0.85 in x 4.15 in)
Per drawing # 139255
Weight:
314 g (0.69 lb)
Certification
Number
CSA 1166985
Environmental Limits
Operating
Temperature:
European/ATEX
II 3G EEx nA [L] IIC T4
-20C to + 70C (-4F to +158F)
LCIE 00ATEX6016X
T4 @ -30C = Ta = +70C
Storage
Temperature:
-40C to + 85C (-40F to +185F)
II 1/3 G EEx nA[ia] ia IIC T4
Operating
Humidity:
LCIE 00ATEX6017X
relative humidity
T4 @ -30C = Ta = +70C
Brazil
Br-Ex nA [nL] IIC T4
Storage
Humidity:
MC, AEX-8304-X
relative humidity
T4 @ -30C = Ta = +70C

Rev. F (11/08)
Page 6 of 7
Dimensional Drawing
21.6
(0.85)
105.3
(4.15)
126.9 (5.00)
Dimensions are in millimetres (inches)
Bently Nevada, FieldMonitor, Proximitor and NSv are trademarks of General Electric Company.
Copyright 1999. Bently Nevada LLC.
1631 Bently Parkway South, Minden, Nevada USA 89423
Phone: 775.782.3611
Fax: 775.215.2873
www.ge-energy.com/bently
All rights reserved.
Rev. F (11/08)
Page 7 of 7

1701/15 Fieldmonitor™ Proximitor Input Monitor For Radial Vibration and Thrust Position

Uploaded by

Copyright:

Available Formats

1701/15 Fieldmonitor™ Proximitor Input Monitor For Radial Vibration and Thrust Position

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

1701/15 Fieldmonitor™ Proximitor Input Monitor For Radial Vibration and Thrust Position

Uploaded by

Copyright:

Available Formats

1701/15 FieldMonitor Proximitor Input Monitor

for Radial Vibration and Thrust Position

Shaft relative radial vibration

Shaft radial position (see note)

Shaft axial position (i.e., thrust position)

Specifications and Ordering Information

Direct (Overall), Gap

Over Alarm 1 & 2 on Direct,

Internal galvanically isolated barrier (requires

Supported Transducer I/O Modules

Internal 3300 5-metre Proximitor

Signal Processing Options

Internal 3300 NSv 7-metre

Internal 7200 5-metre Proximitor

Specifications at 25C (77F)

Proximitor / Accelerometer I/O

External Proximitor Options

3000 -18 Volt

30 m (100 ft) cable at 60pF/ft, not

Specifications and Ordering Information

127 mm x 21.6 mm x 105 mm

Signal Processing Options

1701/15 Proximitor Input Monitor - Thrust

Over/Under Alarm 1 & Alarm 2 on

External Proximitor Options

Away from probe

Set using I/O data tables

Internal galvanically isolated barrier (requires

Transducer I/O Module Options

Specifications at 25C (77F)

Internal galvanically isolated

-24 V, + 5 V, from 1701 Power

Proximitor / Accelerometer I/O

1.5 Watt (not including

Proximitor Input Monitor for Radial Vibration and Thrust

30 m (100 ft) cable at 60pF/ft, not

Hazardous Area Approvals

(5 in x 0.85 in x 4.15 in)

Per drawing # 139255

-20C to + 70C (-4F to +158F)

II 1/3 G EEx nA[ia] ia IIC T4

Specifications and Ordering Information

Dimensions are in millimetres (inches)

You might also like